diff --git "a/data_local/delucionqa_chunked_docs.json" "b/data_local/delucionqa_chunked_docs.json"
new file mode 100644--- /dev/null
+++ "b/data_local/delucionqa_chunked_docs.json"
@@ -0,0 +1 @@
+["Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to", "equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is", "how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.", "Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Drag & Drop Menu Bar The Uconnect features and services in the main menu bar are easily customized for your preference.", "The Uconnect features and services in the main menu bar are easily customized for your preference.  Simply follow these steps: press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Note: This feature is only available if the vehicle is in PARK.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the", "to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the", "select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF", "one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the", "equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power", "equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Key Left Vehicle Feature If a valid key fob is no longer detected inside the vehicle while the vehicle\u2019s ignition system is in the ON/RUN or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument cluster display along with an interior chime.  An exterior audible and visual alert will also be activated to warn the driver.  The vehicle\u2019s horn will rapidly chirp three times along with a single flash of the vehicle\u2019s exterior lights.  Note: The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  Front door removal front door removal \u00b9 use this qr code to access your digital experience.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted", "doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  To remove the front doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nut from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin located under the rear seat.  Hinge pin nut remove the plastic wiring access door under the instrument panel by sliding the plastic panel along the door frame toward the seats until the tabs are detached.  Wiring access door note: do not force open; this will break the plastic cover.  Pull up on the red locking tab to unlock the wiring harness.  Closed wiring harness 1 \u2014 red locking tab 2 \u2014 wiring harness lever (closed position) push and hold down the black security tab under the wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014 wiring", "wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014 wiring harness lever (open position) 2 \u2014 black security tab with the wiring harness open, pull straight downward on the wiring connector to unplug.  Store the wiring connector in the lower door basket.  With the door in the open position, remove the check screw from the door check attachment on the body side (using a #T40 Torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  See note below if the check arm gets pushed into the door while the door is off.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.", "operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Note: When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the", "Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "US/CANADA Exposure to Radio Frequency Radiation The radiated output power of the internal wireless radio is far below the FCC and IC radio frequency exposure limits.  Nevertheless, the wireless radio will be used in such a manner that the radio is 8 inches (20 cm) or further from the human body.  The internal wireless radio operates within guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community.  The radio manufacturer believes the internal wireless radio is safe for use by consumers.  The level of energy emitted is far less than the electromagnetic energy emitted by wireless devices such as mobile phones.  However, the use of wireless radios may be restricted in some situations or environments, such as aboard airplanes.  If you are unsure of restrictions, you are encouraged to ask for authorization before turning on the wireless radio \"\u21e8general information\" .  Connected Vehicles Privacy of any wireless and wired communications cannot", "information\" .  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to", "equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.", "As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Connected Vehicles Privacy of any", "the Vehicle Security Light in the instrument cluster will flash.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.", "Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:  ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will", "START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.", "that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).", "Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety", "any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province,", "including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where", "Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html frequently asked questions about installing child restraints with seat belts what is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child", "anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward-facing child restraint, up to the recommended weight limit of the child restraint.  Can the rear-facing child restraint touch the back of the front passenger seat?  Yes contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.  Can the rear head restraints be removed?  Yes the center head restraint can be removed if it interferes with the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint?  No do not twist the buckle stalk in a seating position with an alr retractor.  Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the", "and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.  Use this simple 5-step test to decide whether the child can use the vehicle\u2019s seat belt alone: Can the child sit all the way back against the back of the vehicle seat?  Do the child\u2019s knees bend comfortably over the front of the vehicle seat while the child is still sitting all the way back?  Does the shoulder belt cross the child\u2019s shoulder between the neck and arm?  Is the lap part of the belt as low as possible, touching the child\u2019s thighs and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to any of these questions was \u201cno,\u201d then the child still needs to use a booster seat in this vehicle.  If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s squirming or slouching can move the belt out of position.  If the shoulder belt contacts the", "squirming or slouching can move the belt out of position.  If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.  WARNING: Never allow a child to put the shoulder belt under an arm or behind their back.  In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.  A child must always wear both the lap and shoulder portions of the seat belt correctly.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.", "is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL", "fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is", "center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Warm up the engine before", "vehicle's obd ii system is ready and you can proceed to the i/m station.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds", "do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.", "Door Frame Installation Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten fasteners target torque specification for torx fasteners maximum minimum 44.2 in-lb (5 n\u00b7m) 53.1 in-lb (6 n\u00b7m) 35.4 in-lb (4 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of", "door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step five step five insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  To remove the half-doors, repeat the installation steps in reverse order.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to", "from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate", "not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  If the check arm is stuck inside the door, follow these instructions to install the check arm.  To reinstall the door(s), perform the previous steps in the reverse order.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  To install the front door exterior mirrors on the half-doors, proceed as follows: To install the front or rear half-doors, proceed as follows: Locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place Tool Into Service Hole Of Plug To Remove Using the tool, slowly pull upwards from the center of the plug to remove.  Upon first", "To Remove Using the tool, slowly pull upwards from the center of the plug to remove.  Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  Only adjust the door to fit correctly against the striker.  DO NOT adjust the striker, as this could affect the positioning of the full door.  Half-Door Installation To install the front or rear half-doors, proceed as follows: Remove the full doors from the vehicle.  For front door removal, see For rear door removal, see Locate the upper and lower hinge pins on the lower half-door, and lower them into the body hinges on the vehicle.  Note: the upper hinge pin is longer, which can be used to assist in guiding the door into place during installation.  Lower half-door hinge pins insert the upper and lower hinge pin screws into the body hinges.  Tighten the screws using a #T50 Torx", "the upper and lower hinge pin screws into the body hinges.  Tighten the screws using a #T50 Torx head driver to 3.8 ft\u00b7 lb / 5.2 N\u00b7m.  Caution: do not close the door before reattaching the door check to the body.  Damage may occur to the door check.  Do not overtighten Torx fasteners, damage to the vehicle\u2019s parts will occur.  Hinge pins can break if overtightened during door install (Max Torque: 6.0 ft\u00b7 lb/8.1 N\u00b7m).  Attach the cloth strap of the lower half-door to the metal hook just inside the vehicle.  Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap connect the wiring harness on the lower half-door to the connection just inside the vehicle.  Note: for front doors, make sure the wiring harness is closed completely.  Front door wiring harness 1 \u2014 open wiring harness 2 \u2014 closed wiring harness replace wiring access doors.  When the half-doors are shipped with the vehicle, the lower half-doors will have plugs in the post holes that must be removed prior to upper half-door installation.  To remove these", "in the post holes that must be removed prior to upper half-door installation.  To remove these plugs, proceed as follows: locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place tool into service hole of plug to remove using the tool, slowly pull upwards from the center of the plug to remove.  Making sure the window on the upper half-door is completely zipped closed, insert the upper half-door into the lower half-door by placing the posts into the post holes.  Lower the upper half-door into post holes push down firmly on the inside of the upper half-door until it is fully seated in the lower half.  Push Down To Fully Seat Upper Half-Door", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service", "is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors", "a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software,", "into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact", "you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by", "updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but", "engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.", "the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Opening The Hood Release both of the outside hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Note: Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.", "When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Note: depending on the vehicle\u2019s options, feature settings may vary.  To Activate Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.  WARNING: Leaving the Cruise Control system on when not in use is dangerous.  You could accidentally set the system or cause it to go faster than you want.  You could lose control and have an accident.  Always ensure the system is off when you are not using it.  STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery:", "we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan", "hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the", "image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check", "to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  Normal Starting Observe the instrument cluster lights when starting the engine.  Always apply the parking brake.", "Observe the instrument cluster lights when starting the engine.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  Note: a delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  Caution: if the water in fuel indicator light remains on, do not start the engine before you drain the water from the fuel filters to avoid engine damage.  The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Note: Normal starting of either a cold or a warm engine is", "turned off.  Release the parking brake.  Note: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades", "conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Stopping The Engine After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Note: Refer to the following chart for proper engine shutdown.  Note: Under certain conditions the Stop/Start system may be temporarily disabled and the engine fan will run after the engine is turned off to protect the engine.  These conditions are under high load and high temperature conditions.", "Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.", "in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If You Stall Or Begin To Lose Headway If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally", "REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of", "more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If the engine stalls or you lose", "the risk of a rollover, which may result in severe injury.  If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight", "it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.", "The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Retrieve funnel from under the right rear seat.  Fuel Funnel Location Refueling Funnel Remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting Funnel Ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from", "an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  The vehicle may be equipped with a refueling funnel.", "the clutch to overheat and cause a fire.  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  The engine may be switched off even if the warning light is on: repeated interruptions of the regeneration process could cause an early deterioration of engine oil.  For this reason it is always advisable to wait for the symbol to go off before turning off the engine, following the previously mentioned instructions.  Do not complete the DPF regeneration process when the vehicle is stopped.  See the following steps for refueling: Emergency Gas Can Refueling Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil", "periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note:", "reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow", "is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in", "warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.", "If Engine Fails To Start If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  WARNING: Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged", "engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly CAUTION: To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more", "the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  Engine is not started.  Some electrical devices are available (power windows, etc.  FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  Do Not Operate The Engine", "another brand of gasoline before considering service for the vehicle.  Do Not Operate The Engine With Failed Parts All engine failures give some warning before the parts fail.  Be on the alert for changes in performance, sounds, and visual evidence that the engine requires service.  Some important clues are: engine misfiring or vibrating severely sudden loss of power unusual engine noises fuel, oil or coolant leaks sudden change, outside the normal operating range, in the engine operating temperature excessive smoke oil pressure drop shifting fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the", "released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.", "To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries", "system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster", "in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The Autostop Mode, The Following Must Occur: Conditions That Will Cause The Engine To Start Automatically While In Autostop Mode: To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: Conditions that will cause the engine to start automatically while in STOP/START AUTOSTOP ACTIVE mode, the engine will start automatically when: This indicator light will illuminate when the Stop/Start function is in \u201cAutostop\u201d mode.  The Stop/Start feature is enabled after every normal engine start.  It will remain in", "mode.  The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  While in an Autostop, the Climate Control system may automatically adjust airflow to maintain cabin comfort.  Customer settings will be maintained upon return to an engine running condition.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This light alerts the driver that the vehicle is in the neutral mode", "If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The", "the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye", "Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction", "shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause", "when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the", "pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.", "of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist", "fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric topDo not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing", "use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your", "perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the", "and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use", "with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You", "Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Android Auto\u2122 allows you to access and stream your favorite music with apps like YouTube Music, iHeartRadio, and Spotify.  Using your smartphone\u2019s data plan, you can stream endless music on the road.  Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the", "a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  To use Android Auto\u2122 on your car display, you\u2019ll need an", "bar changes to the Android Auto\u2122 icon.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: The Android Auto\u2122 App displays", "your apps.  To use Android Auto\u2122, perform the following procedure: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a", "icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your", "data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you", "data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .", "4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front wheels.  The four-wheel drive system will be automatically engaged when the vehicle senses a loss of traction.  This range provides additional traction for varying road conditions.  2H Two-Wheel Drive High Range \u2014 This range is for normal street and highway driving on dry, hard surfaced roads.  4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front wheels.  The four-wheel drive system will be automatically engaged when the vehicle senses a loss of traction.  This range provides additional traction for varying road conditions.  4H Four-Wheel Drive High Range \u2014 This range maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction for loose, slippery road surfaces only.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together,", "the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L 4H The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.", "For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government", "ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction", "traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.  Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  Temperature Grades The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of", "grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.  Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.", "Cruise Control When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  The Cruise Control buttons are located on the right side of the steering wheel.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  Do not use in hilly terrain or with heavy loads.  When using the Cruise Control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.  Use Cruise Control in flat terrain and with", "disengage until you can get back to cruising speed.  Use Cruise Control in flat terrain and with light loads to maximize fuel efficiency.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise", "vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.", "Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information Placard", "tire size, and cold tire inflation pressures specified on the Tire And Loading Information Placard To determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on gawrs, vehicle loading, and trailer towing, see \"\u21e8vehicle loading\" .  Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading", "pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on GAWRs, vehicle loading, and trailer towing, see Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The", "driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.", "When using the AutoStick shift control, select the highest gear that allows for adequate performance and avoids frequent downshifts.  For example, choose \u201c5\u201d if the desired speed can be maintained.  Choose \u201c4\u201d or \u201c3\u201d if needed to maintain the desired speed.  To prevent excess heat generation, avoid continuous driving at high RPM.  Return to a higher gear or vehicle speed when grade and road conditions allow.  Pushing the set (+) , or set (-) button once will result in a 1 km/h speed adjustment.  Each subsequent tap of the button results in an adjustment of 1 km/h.  If the button is continually pushed, the set speed will continue to adjust in 10 km/h increments until the button is released, then the new set speed will be established.  Pushing the set (+) , or set (-) button once will result in a 1 km/h speed adjustment.  Each subsequent tap of the button results in an adjustment of 1 km/h.  If the button is continually pushed, the set speed will continue to adjust in 10 km/h increments until the button is", "continually pushed, the set speed will continue to adjust in 10 km/h increments until the button is released,The new set speed is reflected in the instrument cluster display.  To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster", "speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is", "ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speed", "To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  To remove the center head restraint, raise it as far as it can go.  Then, push the adjustment button and the release button at the base of each post while pulling the head restraint up.  A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  To raise the head restraint, pull upward on the head restraint.  To lower the head restraint,", "To raise the head restraint, pull upward on the head restraint.  To lower the head restraint, push the adjustment button located on the base of the head restraint, and push downward on the head restraint.  The release button does not need to be pushed to adjust the head restraint.  To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then, adjust it to the appropriate height using the adjustment button.  For information on child seat tether routing, see A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the", "occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  Do not drive the vehicle without the rear seat head restraints installed while passengers are occupying the rear seat.  In a collision, people riding in this area without the head restraints installed are more likely to be seriously injured or killed.  A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  Front Head Restraints To", "instructions prior to operating the vehicle or occupying a seat.  Front Head Restraints To raise the head restraint, pull upward on the head restraint.  To lower the head restraint, push the adjustment button located on the base of the head restraint, and push downward on the head restraint.  The release button does not need to be pushed to adjust the head restraint.  To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  WARNING: A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.", "ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  Note: Do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head.", "With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeHow long does it take to remotely start my vehicle?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will remote start your vehicle more quickly.  However its range is limited.  For example, when you are leaving the stadium after the game, you can use the Vehicle Branded App to remote start your vehicle and have the inside of", "the game, you can use the Vehicle Branded App to remote start your vehicle and have the inside of your vehicle comfortable by the time you get to it.  Will my vehicle be safe if I lose my wireless device?  People sometimes lose their wireless devices, which is why security measures have been engineered into the Vehicle Branded App.  Asking for your username, password and SiriusXM Guardian\u2122 Security PIN help to ensure that nobody can start your vehicle if they happen to find your device.  Can someone drive off with my vehicle using the App?  nob Driving your vehicle still requires the keys to be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the interior before you arrive.  Can I stop a vehicle that is being driven with the cancel Remote Vehicle Start command?  nob If the vehicle is in motion, the cancel Remote Vehicle Start button will not stop the vehicle.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work", "all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeThis remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  With Remote Start, the engine will only run for 15 minutes.", "Remote Start system.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, see These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.", "If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized", "In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d This warning light will turn on when there's a fault with the EPS system When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes", "and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  Push the SWAY BAR switch to disconnect or connect the sway bar.  The Sway Bar Indicator Light (located in the instrument cluster) will illuminate when the bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when activation conditions are not met.  The stabilizer/sway bar should remain in on-road mode during normal driving conditions.  The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.  If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response", "with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off CAUTION:", "are safe, pull over and let vehicle idle for a few moments until the light turns off CAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen", "out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with", "wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.", "for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Electric Power Steering (EPS) Fault Warning Light This warning light will turn on when there's a fault with the EPS system WARNING: Continued operation with reduced assist could pose a safety risk to yourself and others.  Service should be obtained as soon as possible.  If the \u201cPOWER STEERING HOT\u201d message and an", "Service should be obtained as soon as possible.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offIf the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  The heated steering wheel button is located on the center of", "is applying the brakes autonomously.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering", "and cause a fire.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  This warning light will turn on when there's a fault with the EPS system The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.", "The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  Upper Center None Time Current Econ Compass Range to Empty Trip A Distance Audio Average Econ Trip B Distance Outside Temp Menu Title Speedometer Adjustable Upper Anchorage If the compression is increased too much on the front upper corner of the rear doors, deformation of the seal will occur.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the", "Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the", "Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the", "or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "To enter the \u201cPartial Off\u201d mode, momentarily push the ESC OFF button and the ESC OFF Indicator Light will illuminate.  To turn the ESC on again, momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Automatic Headlight System will turn the headlights on or off according to ambient light levels.  To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation.  When the system is on, the headlight time delay feature is also on.  This means the headlights will stay on for up to 90 seconds (programmable through the uconnect settings \"\u21e8uconnect settings\" ) after you place the ignition into the off position.  To turn the automatic system off, move the", ") after you place the ignition into the off position.  To turn the automatic system off, move the headlight switch out of the AUTO position.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Reduce power to unnecessary loads if possible: Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets", "Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s exterior and interior lights.  When the \u201cDaytime Running Lights\u201d feature is selected, the daytime running lights can be turned on or off.  This feature is only allowed by law in the country of the vehicle purchase.  Depending on the vehicle\u2019s options, feature settings may vary.  Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your", "on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices", "use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  Interior Courtesy Lights When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn", "panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.", "Trac-Lok Rear Axle \u2014 If Equipped The Trac-Lok rear axle provides a constant driving force to both rear wheels and reduces wheel spin caused by the loss of traction at one driving wheel.  If traction differs between the two rear wheels, the differential automatically proportions the usable torque by providing more torque to the wheel that has traction.  Trac-Lok is especially helpful during slippery driving conditions.  With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction.  WARNING: On vehicles equipped with a limited-slip differential, never run the engine with one rear wheel off the ground.  The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of your vehicle.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum", "and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not", "same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to", "to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on", "road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road", "there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.", "4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together,", "the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any", "drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H", "rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.", "each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  2H (Two-Wheel Drive High Range) 4H (Four-Wheel Drive High Range) N (Neutral) 4L (Four-Wheel Drive Low Range) In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal", "4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L", "To Turn On The Engine Using The ENGINE START/STOP Button The transmission must be in PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage automatically after 10 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Stop the vehicle.  Shift the transmission into PARK, if possible.  If not, shift the transmission to NEUTRAL.  Push and hold the ENGINE START/STOP button until the engine turns off.  Wait approximately 30 seconds.  Restart the engine.  Shift into the desired gear range.  If the problem is no longer detected, the transmission will return to", "into the desired gear range.  If the problem is no longer detected, the transmission will return to normal operation.  To Turn On The Engine Using The ENGINE START/STOP Button  Normal Starting Observe the instrument cluster lights when starting the engine.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  Note: a delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  Caution: if the water in fuel indicator light remains on, do not start the engine before you drain the water from the fuel filters to avoid engine damage.  The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting,", "after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Note: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving", "weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Stopping The Engine After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Note: Refer to the following chart for proper engine shutdown.  Note: Under certain conditions the Stop/Start system may be temporarily disabled and the engine fan will run after the engine is turned off to protect the engine.  These conditions are under high load and high", "the engine is turned off to protect the engine.  These conditions are under high load and high temperature conditions.", "Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer", "15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.", "Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light", "can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.", "FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) NEUTRAL (N)  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear", "the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.", "Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant will return to the radiator from the coolant expansion bottle/recovery tank if so equipped.  The cap should be inspected and", "from the coolant expansion bottle/recovery tank if so equipped.  The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.  WARNING: Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  Potential signs of vehicle overheating: Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do", "scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.", "Key Left Vehicle Feature If a valid key fob is no longer detected inside the vehicle while the vehicle\u2019s ignition system is in the ON/RUN or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument cluster display along with an interior chime.  An exterior audible and visual alert will also be activated to warn the driver.  The vehicle\u2019s horn will rapidly chirp three times along with a single flash of the vehicle\u2019s exterior lights.  Note: The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Key Left Vehicle Feature If a valid key fob is no longer detected inside the vehicle while the vehicle\u2019s ignition system is in the ON/RUN or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument", "or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument cluster display along with an interior chime.  An exterior audible and visual alert will also be activated to warn the driver.  The vehicle\u2019s horn will rapidly chirp three times along with a single flash of the vehicle\u2019s exterior lights.  Note: The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Off Road+ Indicator Light \u2014 If Equipped This indicator light will illuminate when Off Road+ has been activated.  Sway Bar Indicator Light \u2014 If Equipped This indicator light will illuminate when the front sway bar is disconnected.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and", "which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic", "subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .", "Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d", "and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.", "of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear", "Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as", "bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and", "up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up", "the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear", "can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.", "START The engine will start.  Note: In case the ignition switch does not change with the push of the START/STOP ignition button, the key fob may have a low or depleted battery.  In this situation, a backup method can be used to operate the ignition switch.  Put the nose side of the key fob (side with the mechanical flip key) against the START/STOP ignition button and push to operate the ignition switch.  CAUTION: Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.  WARNING: When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.", "is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the Keyless Enter \u2018n Go\u2122 Ignition in the ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat buildup may cause serious injury or death.  CAUTION: An unlocked vehicle is an invitation for thieves.  Always remove key fob from the vehicle and lock all doors when leaving the vehicle unattended.  Note: When opening the driver's door with the ignition in the ON/RUN (engine not running) position, a chime will sound to remind you to place the ignition in the OFF position.  In addition to the chime, the message will display \u201cIgnition Or Accessory On\u201d in the cluster.  Key Left Vehicle Feature If a", "the message will display \u201cIgnition Or Accessory On\u201d in the cluster.  Key Left Vehicle Feature If a valid key fob is no longer detected inside the vehicle while the vehicle\u2019s ignition system is in the ON/RUN or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument cluster display along with an interior chime.  An exterior audible and visual alert will also be activated to warn the driver.  The vehicle\u2019s horn will rapidly chirp three times along with a single flash of the vehicle\u2019s exterior lights.  Note: The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or", "Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do", "in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "Crossing Logs To cross a log, approach it at a slight angle (approximately 10 to 15 degrees).  This allows one front tire to be on top of the log while the other just starts to climb the log.  While climbing the log, modulate your brake and accelerator to avoid spinning the log out from under your tires.  Then ease the vehicle off the log using your brakes.  CAUTION: Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high-centered.  Before You Cross Any Type Of Water As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and", "can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Crossing A Ravine, Gully, Ditch, Washout Or Rut When crossing a ravine, gully, ditch, washout or a large rut, the angled approach is the key to maintaining your vehicle's mobility.  Approach these obstacles at a 45-degree angle and let each tire go through the obstacle independently.  You need to use caution when crossing large obstacles with steep sides.  Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover.  If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires.  Use the removed dirt to fill the rut ahead of the turnout you just created.  You should now be able to drive out", "dirt to fill the rut ahead of the turnout you just created.  You should now be able to drive out following the trench you just created at a 45-degree angle.  WARNING: There is an increased risk of rollover when crossing an obstacle, at any angle, with steep sides.", "Non-Locking Storage Wall The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  There is also an option to remove the wall by removing the four bolts that connect the storage wall to the floor.  Non-Locking Storage Wall The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  There is also an option to remove the wall by removing the four bolts that connect the storage wall to the floor.  Rear Wall Storage Bin To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  Note: The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  The Locking Storage Bin has two keyed locks on the front of", "to limit access to items behind seat.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.", "If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for serviceIn unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature", "whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the", "procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an", "reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns", "will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a", "clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service,", "overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is", "Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  If the vehicle is overheating, it will need to be serviced by an authorized dealer.", "EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to", "but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than", "was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.", "and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start", "10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M", "during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident,", "compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's", "illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "To enter the \u201cPartial Off\u201d mode, momentarily push the ESC OFF button and the ESC OFF Indicator Light will illuminate.  To turn the ESC on again, momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Automatic Headlight System will turn the headlights on or off according to ambient light levels.  To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation.  When the system is on, the headlight time delay feature is also on.  This means the headlights will stay on for up to 90 seconds (programmable through the uconnect settings \"\u21e8uconnect settings\" ) after you place the ignition into the off position.  To turn the automatic system off, move the", ") after you place the ignition into the off position.  To turn the automatic system off, move the headlight switch out of the AUTO position.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Reduce power to unnecessary loads if possible: Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets", "Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s exterior and interior lights.  When the \u201cDaytime Running Lights\u201d feature is selected, the daytime running lights can be turned on or off.  This feature is only allowed by law in the country of the vehicle purchase.  Depending on the vehicle\u2019s options, feature settings may vary.  Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your", "on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices", "use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn", "panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  Interior Courtesy Lights When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time", "the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.", "Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate", "provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.", "on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.", "Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be", "Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire dealer or original", "those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result", "what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw", "accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  Tires Examine tires for excessive tread wear and uneven wear patterns.  Check for stones, nails, glass, or other objects lodged in the tread or sidewall.  Inspect the tread for cuts and cracks.  Inspect sidewalls for cuts, cracks, and bulges.  Check the lug nut/bolt torque for tightness.  Check the tires (including spare) for proper cold", "Check the lug nut/bolt torque for tightness.  Check the tires (including spare) for proper cold inflation pressure.", "To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security", "Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped)Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the", "armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open", "arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second", "action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.", "When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is", "the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an", "brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the", "the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  If the headlights or parking lights are left on after the ignition is placed in the OFF position, the vehicle will chime when the driver\u2019s door is opened.  Vehicle parking brake is applied Stability event occurs Gear selector is moved out of DRIVE Engine overspeed occurs Clutch pedal is pressed (manual transmission only) Vehicle is operating at a low RPM (manual transmission only) Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five", "brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  release the parking brake  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System", "system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If", "monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake", "it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.", "Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  The rearview mirror can be adjusted up, down, left, and right.  The mirror", "for on-road use.  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  Manual Mirror Adjustment If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the", "reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Ignoring the Rearview Mirror light could mean you will not have SOS Call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  When cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray", "cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on the mirror.", "Off-Road Driving Tips  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled", "you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface", "should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?", "Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or", "with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of", "and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match", "Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl", "or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.", "Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect", "against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.", "vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code", "leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants", "are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the", "the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric topDo not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Place the vehicle in a warm", "installation can cause water to leak into the vehicle's interior.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  From the Sunrider\u00ae Position, remove straps if previously secured.  Step One Failure to follow the next steps could result in damage to the soft top or vehicle.  Using the side link, lift and push the soft top toward the front of the vehicle, manually guiding the top into the closed position.  Step Two Step Two From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Step Three Pull the handle back upward while squeezing the hook, locking the latch into place.  Step Four It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water", "it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information Placard To determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on gawrs, vehicle loading, and trailer towing, see \"\u21e8vehicle loading\" .  Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not", "on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on GAWRs, vehicle loading, and trailer towing, see Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed", "axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  All cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb", "transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  (1) Locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.\u201d on your vehicle's placard.", "Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose", "the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.", "and power steering, and fill as needed.  Check function of all interior and exterior lights.  PARKING BRAKE Before exiting the vehicle, make sure that the parking brake is fully applied.  Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or FIRST gear.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to", "selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  WARNING: Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  CAUTION: If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  You or others could be injured", "Have the brake system serviced by an authorized dealer immediately.  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied.  The parking brake should always be applied when the driver is not in the vehicle, especially on an incline.  Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle,", "parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the", "in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.", "For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government", "ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction", "traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.  DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces", "stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.", "The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  Drivetrain Menu 2WD/4WD Drivetrain  Drivetrain The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  The following information is displayed: steering angle in degrees status of transfer case status of front axles \u2014 if equipped status of the rear axles \u2014 if equipped.  Drivetrain The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  The following information is displayed: steering angle in degrees status of transfer case status of front axles \u2014 if equipped status of the rear axles \u2014 if equipped drivetrain front wheel angle: displays the graphical and numerical value of calculated average front wheel angle from the steering wheel orientation.  Transfer Case Lock Status: displays \u201cLock\u201d graphic only during 4WD High, 4WD Auto, or 4WD Low status.  Axle Lock And Sway Bar Status (if equipped): displays front and rear or rear only axle locker graphic, and sway bar connection graphic with", "displays front and rear or rear only axle locker graphic, and sway bar connection graphic with text message (connected or disconnected).", "The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  Power Window Switches Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel", "10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.  Feature description controls \u2014 if equipped press the controls button to access vehicle-specific features like heated seats and steering wheel.  Apps press the apps button to access a list of the available mobile apps.  Climate press the climate button to enter climate mode and access the climate control functions.  Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF.  Climate Control OFF Button Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  Recirculation Button Push the Recirculation button on the faceplate to change the system between recirculation mode and outside air mode.  The Recirculation indicator and the A/C indicator (if equipped) illuminate when the", "air mode.  The Recirculation indicator and the A/C indicator (if equipped) illuminate when the Recirculation button is pressed.  Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.  Recirculation can be used in all modes except for Defrost.  Recirculation may be unavailable if conditions exist that could create fogging on the inside of the windshield.  The A/C can be deselected manually without disturbing the mode control selection.  Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur.  Extended use of this mode is not recommended.  On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode to improve window clearing operation.  Recirculation is disabled automatically if this mode is selected.  Attempting to use Recirculation while in this mode causes the LED on the control button to blink and then turn off.  Recirculation Button Press and release this button on the", "button to blink and then turn off.  Recirculation Button Press and release this button on the touchscreen, or push the button on the faceplate to change the system between recirculation mode and outside air mode.  The Recirculation indicator and the A/C indicator illuminate when the Recirculation button is pressed.  Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.  Recirculation can be used in all modes Recirculation may be unavailable (button on the touchscreen grayed out) if conditions exist that could create fogging on the inside of the windshield.  The A/C can be deselected manually without disturbing the mode control selection.  Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur.  Extended use of this mode is not recommended.  Recirculation mode may automatically adjust to optimize customer experience for warming, cooling, dehumidification, etc.  POWER WINDOWS \u2014 IF EQUIPPED The power windows", "for warming, cooling, dehumidification, etc.  POWER WINDOWS \u2014 IF EQUIPPED The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The top left switch controls the left front window and the top right switch controls the right front window.  The bottom left switch controls the left rear window and the bottom right switch controls the right rear window.  WARNING: Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  Note: The power window switches will remain active for up to 10 minutes after the", "injury or death.  Note: The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Preparations For Jacking Park on a firm, level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking", "operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  With extended use the Hazard Warning Flashers may wear down your battery.  The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue", "When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Hazard Warning Flashers Button The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  This is an emergency", "the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.  turn on the Hazard Warning Flashers.  Apply the parking brake firmly and shift an automatic transmission in PARK; a manual transmission to REVERSE.  Block the wheel diagonally opposite the wheel to be raised.  Never start or run the engine with the vehicle on a jack.  Do not let anyone sit in the vehicle when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.  Only use the jack in the positions indicated and for lifting this vehicle during a tire change.  If working on or near a roadway, be extremely careful of", "this vehicle during a tire change.  If working on or near a roadway, be extremely careful of motor traffic.  To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  Yellow indicator lights 4wd indicator light \"\u21e84wd indicator light \u2014 if equipped\" 4wd low indicator light \"\u21e84wd low indicator light \u2014 if equipped\" 4wd part time indicator light \"\u21e84wd part time indicator light \u2014 if equipped\" axle locker fault indicator light \"\u21e8axle locker fault indicator light \u2014 if equipped\" rear axle lock indicator light \"\u21e8rear axle lock indicator light \u2014 if equipped\" front and rear axle lock indicator light \"\u21e8front and rear axle lock indicator light \u2014 if equipped\" forward collision warning off indicator light \"\u21e8forward collision warning off indicator light \u2014 if equipped\" neutral indicator light \"\u21e8neutral indicator light \u2014 if equipped\" sway bar indicator light \"\u21e8sway", "neutral indicator light \"\u21e8neutral indicator light \u2014 if equipped\" sway bar indicator light \"\u21e8sway bar indicator light \u2014 if equipped\" off road+ indicator light \"\u21e8off road+ indicator light \u2014 if equipped\" cargo light on indicator light \"\u21e8cargo light on indicator light\" wait to start indicator light \"\u21e8wait to start indicator light \u2014 if equipped\" low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \"\u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped\" water in fuel indicator light \"\u21e8water in fuel indicator light \u2014 if equipped\" selec speed control (ssc) indicator light \u2014 if equipped this light will turn on when selec speed control is activated.  Selec Speed Control is available in 4WD Low ONLY.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear", "forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  Yellow indicator lights 4wd indicator light  \u21e84wd indicator light \u2014 if equipped  4wd low indicator light  \u21e84wd low indicator light \u2014 if equipped  4wd part time indicator light  \u21e84wd part time indicator light \u2014 if equipped  axle locker fault indicator light  \u21e8axle locker fault indicator light \u2014 if equipped  rear axle lock indicator light  \u21e8rear axle lock indicator light \u2014 if equipped  front and rear axle lock indicator light  \u21e8front and rear axle lock indicator light \u2014 if equipped  forward collision warning off indicator light", "and rear axle lock indicator light \u2014 if equipped  forward collision warning off indicator light  \u21e8forward collision warning off indicator light \u2014 if equipped  neutral indicator light  \u21e8neutral indicator light \u2014 if equipped  sway bar indicator light  \u21e8sway bar indicator light \u2014 if equipped  off road+ indicator light  \u21e8off road+ indicator light \u2014 if equipped  cargo light on indicator light  \u21e8cargo light on indicator light  wait to start indicator light  \u21e8wait to start indicator light \u2014 if equipped  low diesel exhaust emissions additive adblue\u00ae (urea) indicator light  \u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped  water in fuel indicator light  \u21e8water in fuel indicator light \u2014 if equipped  green indicator lights 4wd auto indicator light  \u21e84wd auto indicator light \u2014 if equipped  front fog indicator light  \u21e8front fog indicator light \u2014 if equipped  parking/headlights on indicator light  \u21e8parking/headlights on indicator light  stop/start active indicator light  \u21e8stop/start", "light  \u21e8parking/headlights on indicator light  stop/start active indicator light  \u21e8stop/start active indicator light \u2014 if equipped  turn signal indicator lights  \u21e8turn signal indicator lights  rear seat belt fastened indicator light.", "Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death", "be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated", "de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Your vehicle may be equipped with a secondary battery used to power the", "to provide starting.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps", "or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.", "Remote Start Windshield Wiper De-Icer Activation \u2014 If Equipped When Remote Start is active and the outside ambient temperature is less than 33\u00b0F (0.6\u00b0C), the Windshield Wiper De-Icer will activate.  Exiting Remote Start will resume previous operation.  If the Windshield Wiper De-Icer was active, the Windshield Wiper De-Icer timer and operation will continue.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.", "could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  Remote Start Front Defrost Activation \u2014 If Equipped When Remote Start is active, and the outside ambient temperature is 40\u00b0F (4.5\u00b0C) or below, the system will automatically activate front defrost for 15 minutes or less.  The time is dependent on the ambient temperature.  Once the timer expires, the system will automatically adjust the settings", "the ambient temperature.  Once the timer expires, the system will automatically adjust the settings depending on ambient conditions.  See \u201cRemote Start Comfort Systems \u2014 If Equipped\u201d in the next section for detailed operation.", "Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel", "only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damageIf climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway", "Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good", "using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  CAUTION: If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage Diesel Fuel Specifications This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine", "tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump", "at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).", "Rolling Code Devices To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Note: The \u201cLEARN\u201d or \u201cTRAIN\u201d button is not the button you normally use to operate the device.  To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Before programming a device to one of your HomeLink\u00ae buttons,", "may vary slightly by manufacturer.  Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  You have 30 seconds in which to initiate rolling code final step 2, after completing rolling code final step 1.  Identifying Whether You Have A Rolling Code Or Non-Rolling Code Device Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.", "Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch", "use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or", "A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious", "is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Maps Push and hold the VR button on the steering wheel until the beep or tap the Microphone icon to ask Apple\u00ae Siri to take you to a desired destination by voice.  You can also touch the Navigation icon in Apple CarPlay\u00ae to access Apple\u00ae Maps.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.", "Apple CarPlay\u00ae Voice Command Apple CarPlay\u00ae allows you to use your voice to interact with Siri through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your iPhone\u00ae and a number of its apps onto your Uconnect touchscreen.  Connect your iPhone\u00ae 5 or higher to one of the media USB ports, using the factory-provided Lightning cable, and press the new Apple CarPlay\u00ae icon that replaces your Phone icon on the main menu bar to begin Apple CarPlay\u00ae.  Push and hold the vr button on the steering wheel, or press and hold the home button within apple carplay\u00ae, to activate siri, which recognizes natural voice commands to use a list of your iphone\u00ae features: phone music messages maps \u2014 if equipped additional apps \u2014 if equipped note: feature availability depends on your carrier and mobile phone maker.  Some Apple CarPlay\u00ae features may not be available in every region and/or language.  Note: Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered", "Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered in the US and other countries.  Apple\u00ae terms of use and privacy statements apply.  Apple carplay\u00ae apple carplay\u00ae \u00b9 use this qr code to access your digital experience.  Uconnect works seamlessly with Apple CarPlay\u00ae, the smarter, more secure way to use your iPhone\u00ae in the car, and stay focused on the road.  Use your Uconnect Touchscreen display, the vehicle's knobs and controls, and your voice with Siri to get access to Apple Music\u00ae, Maps, Messages, and more.  To use Apple CarPlay\u00ae, make sure you are using iPhone\u00ae 5 or later, have Siri enabled in Settings, ensure your iPhone\u00ae is unlocked for the very first connection only, and then use the following procedure: Connect your iPhone\u00ae to one of the media USB ports in your vehicle.  Note: be sure to use the factory-provided lightning cable that came with your phone, as aftermarket cables may not work.  Once the device is connected and recognized, the Phone icon on the", "cables may not work.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Apple CarPlay\u00ae Icon.  Note: apple carplay\u00ae is set to launch immediately.  You can also launch it by pressing the Apple CarPlay\u00ae icon on the touchscreen.  Apple carplay\u00ae and lte data coverage 1 \u2014 lte data coverage 2 \u2014 apple carplay\u00ae icon once apple carplay\u00ae is up and running on your uconnect system, the following features can be utilized using your iphone\u00ae data plan: phone music messages maps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Apple CarPlay\u00ae features may or may not be available in every region and/or language.  Note: To use Apple CarPlay\u00ae, make sure that cellular data is turned on, and that you are in an area with cellular coverage.  Your data and cellular coverage is shown on the left side of the radio screen.  Data plan rates apply.  Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Apple CarPlay\u00ae.  Anywhere using your mobile device and Vehicle Branded App From your computer on the Owner\u2019s Site (not available on all functions) Contacting SiriusXM Guardian\u2122 Customer Care (not available on all functions) Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.", "function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Closing The Hood To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.", "rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  WARNING: Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.", "Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on GAWRs, vehicle loading, and trailer towing, see Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.", "capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.", "GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  For further information on GAWRs, vehicle loading, and trailer towing, see  Gross Axle Weight Rating (GAWR)", "information on GAWRs, vehicle loading, and trailer towing, see  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to", "this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation.  The entire vehicle should first be weighed on a commercial scale to ensure that the GVWR has not been exceeded.  The weight on the front and rear of the vehicle should then be", "the GVWR has not been exceeded.  The weight on the front and rear of the vehicle should then be determined separately to be sure that the load is properly distributed over the front and rear axle.  Weighing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.  If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met.  Store the heavier items down low and be sure that the weight is distributed equally.  Stow all loose items securely before driving.  Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate.  WARNING: Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR.  If you do, parts on your vehicle can break, or it can change the way your vehicle handles.  This could cause you to lose control.  Overloading can shorten the life of your vehicle.", "Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.  Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d The buttons on the right side of the steering wheel operate the ACC system.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged ACC Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following appears in the instrument cluster display:  Driver Assist \u2014 If Equipped The Driver Assist menu displays the status of the ACC system.  Push and release the up or down arrow button", "Assist menu displays the status of the ACC system.  Push and release the up or down arrow button until the driver assist menu is displayed in the instrument cluster display.", "The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Locking Storage Bin (Closed View) Locking Storage Bin  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be", "bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  Locking Storage Bin  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.", "vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.", "To use the mid position, open the tailgate and lower it to near mid position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  Tailgate In Mid Position  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014", "the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located", "provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.", "DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If", "must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne", "corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.", "lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following", "display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122", "auto\u2122.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the", "first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your", "your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android", "factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is", "and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apps The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be", "and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the", "Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Description SmartWatch Integration puts the Vehicle Branded App right on your Apple\u00ae Watch or Android\u2122 Wear.  To get started,", "puts the Vehicle Branded App right on your Apple\u00ae Watch or Android\u2122 Wear.  To get started, follow these steps: Download the Vehicle Branded App from the App Store\u00ae or Google Play.  Log onto the app from your smartphone using the username and password you created when you first set up your account.  Make sure your watch and smartphone are connected through Bluetooth\u00ae.  The Vehicle Branded App should appear on your SmartWatch.  Once the app is downloaded on your SmartWatch, you can enjoy these features: Lock or unlock your vehicle by tapping the remote lock button in the app and entering your security PIN.  Remote start or stop your vehicle.  View important vehicle stats, such as fuel level, vehicle location, tire pressure warning, and more.", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and", "seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information:", "canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html frequently asked questions about installing child restraints with seat belts what is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward-facing child restraint, up to the recommended weight limit of the child restraint.  Can the rear-facing child restraint touch the back of the front passenger seat?  Yes contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.  Can the rear head restraints be removed?  Yes the center head restraint can be removed if it interferes with the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt", "the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint?  No do not twist the buckle stalk in a seating position with an alr retractor.  Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.  Use this simple 5-step test to decide whether the child can use the vehicle\u2019s seat belt alone: Can the child sit all the way back against the back of the vehicle seat?  Do the child\u2019s knees bend comfortably over the front of the vehicle seat while the child is still sitting all the way back?  Does the shoulder belt cross the child\u2019s shoulder between the neck and arm?  Is the lap part of the belt as low as possible, touching the child\u2019s thighs and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to", "and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to any of these questions was \u201cno,\u201d then the child still needs to use a booster seat in this vehicle.  If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s squirming or slouching can move the belt out of position.  If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.  WARNING: Never allow a child to put the shoulder belt under an arm or behind their back.  In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.  A child must always wear both the lap and shoulder portions of the seat belt correctly.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with", "systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.", "If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning", "you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder", "parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  Brake System Warning Light The red Brake System Warning Light will turn on when the", "immediately.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction", "mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force", "equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake", "checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to", "Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera", "Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable", "into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on", "The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable", "into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen", "\u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while", "in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Guide the top of the quarter panel cover assembly up into the retainer.  Step One Failure to follow", "Guide the top of the quarter panel cover assembly up into the retainer.  Step One Failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the Soft Top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step Two It is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step Three From either side, guide the rear window into the retainer while keeping the window level.  Step Four Engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step Five Engage the vertical retainers up the right and", "window is secured in the lower retainer.  Step Five Engage the vertical retainers up the right and left side of the rear window.  Step Six Tuck the rear window under the soft top fabric and press firmly.  Step Seven Engage the rear window retainers in the lower right and left corners.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step Two 1 \u2014 Outside Panel Lock 2 \u2014 Rear Panel Lock 3 \u2014 Front Panel Lock Unlatch the left side header panel latch located at the top of the windshield.  Step Three Remove the left side panel.  Repeat the preceding steps to remove the right side panel.  Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while", "retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage", "the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.", "Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Natural Speech Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Natural speech allows the user to speak commands in phrases or complete sentences.  The system filters out certain non-word utterances and sounds such as \u201cah\u201d and \u201ceh.\u201d The system handles fill-in words such as \u201cI would like to\u201d.  The system handles multiple inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you", "identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you want to call?\u201d in the case where a phone call was requested but the specific name was not recognized.  The system utilizes continuous dialog.  When the system requires more information from the user, it will ask a question to which the user can respond without pushing the Voice Command button on the steering wheel.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear", "the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of", "of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature", "Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.", "Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.  Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d The buttons on the right side of the steering wheel operate the ACC system.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged ACC Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following appears in the instrument cluster display:  Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d", "Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d The buttons on the right side of the steering wheel operate the ACC system.  When the SET (+) or the SET (-) button (located on the steering wheel) is pushed, the display will read \u201cACC SET.\u201d Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following appears in the instrument cluster display: Push the ACC ON/OFF button (located on the steering wheel) until one of the following displays in the instrument cluster display: The Driver Assist menu displays the status of the ACC system.  When driving with ACC engaged and following a vehicle, the system will provide an additional acceleration up to the ACC set speed to assist in passing the vehicle.  This additional acceleration is triggered when the driver utilizes the left turn signal and will only be active when passing on the left hand side.  To turn the system off, push and release the Adaptive Cruise Control", "on the left hand side.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d While ACC with Stop is holding your vehicle at a standstill, if the driver seat belt is unbuckled or the driver door is opened, the ACC with Stop system will cancel and the brakes will release.  A cancel message will display on the instrument cluster display and produce a warning chime.  Driver intervention will be required at this moment.  The specified following distance for ACC can be set by varying the distance setting between four bars (longest), three bars (long), two bars (medium) and one bar (short).  Using this distance setting and the vehicle speed, ACC calculates and sets the distance to the vehicle ahead.  This distance setting displays in the instrument cluster display.", "If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you", "prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides", "a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is", "may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  FOLDING WINDSHIELD The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element provides.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving", "the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  WARNING: Carefully follow these warnings to help protect against personal injury: Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these", "fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "The ACC screen may display once again if any ACC activity occurs, which may include any of the following: This feature will only activate when the following conditions are met: The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: Once SSC is enabled it will activate automatically once the following conditions are met: The following conditions must be met in order for HSA to activate:  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: If the ABS Warning", "also may experience the following normal characteristics when the ABS activates: If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN", "If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To", "by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply", "most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the", "portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.", "Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  The ABS is designed to function with the Original Equipment Manufacturer (OEM) tires.  Modification may result in degraded ABS performance.  Your vehicle is equipped with an advanced Electronic Brake Control (EBC) system.  This system includes Anti-Lock Brake", "with an advanced Electronic Brake Control (EBC) system.  This system includes Anti-Lock Brake System (ABS), Brake Assist System (BAS), Electronic Brake Force Distribution (EBD), Electronic Roll Mitigation (ERM), Electronic Stability Control (ESC), Hill Start Assist (HSA), and Traction Control System (TCS).  These systems work together to enhance both vehicle stability and control in various driving conditions.", "REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engineThis allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from", "monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an", "cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a", "between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The Autostop Mode, The Following Must Occur: Conditions That Will Cause The Engine To Start Automatically While In Autostop Mode: To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: Conditions that will cause the engine to start automatically while in STOP/START AUTOSTOP ACTIVE mode, the engine will start automatically when: This indicator light will illuminate when the Stop/Start function is in \u201cAutostop\u201d mode.  The", "when: This indicator light will illuminate when the Stop/Start function is in \u201cAutostop\u201d mode.  The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  While in an Autostop, the Climate Control system may automatically adjust airflow to maintain cabin comfort.  Customer settings will be maintained upon return to an engine running condition.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow", "the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This light alerts the driver that the vehicle is in the neutral mode  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message", "The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an", "illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.  SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of", "on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is", "the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke", "and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s", "equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.", "2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.", "Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam", "the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.  Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Automatic Dimming Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  This mirror automatically adjusts for", "be adjusted to center on the view through the rear window.  This mirror automatically adjusts for headlight glare from vehicles behind you.  The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Note: The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  Automatic High Beam Headlamp Control \u2014 If Equipped The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automatically controlling the high beams through the use of a camera mounted on the vehicle\u2019s header.  This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.  Note: the automatic high beam headlamp control can be turned on or", "vehicle is out of view.  Note: the automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.", "Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial", "tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Wheel And Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels", "mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Your wheels are susceptible to deterioration caused by salt, sodium chloride, magnesium chloride, calcium chloride, etc., and other road chemicals used to melt ice or control dust on dirt roads.  Use a soft cloth or sponge and mild soap to wipe away promptly.  Do not use harsh chemicals or a stiff brush.  They can damage the wheel\u2019s protective coating that helps keep them from corroding and tarnishing.  When cleaning extremely dirty wheels, including excessive brake dust, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels.  Mopar\u00ae Wheel Treatment or Mopar\u00ae Chrome Cleaner, or their equivalent, is recommended or select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels.  CAUTION: Avoid products", "select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels.  CAUTION: Avoid products or automatic car washes that use acidic solutions or strong alkaline additives or harsh brushes.  Many aftermarket wheel cleaners and automatic car washes may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  CAUTION: Do not use scouring pads, steel wool, a bristle brush, metal polishes, or oven cleaner.  These products may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  Note: If you intend parking or storing your vehicle for an extended period after cleaning the wheels with wheel cleaner, drive your vehicle and apply the brakes to remove the water droplets from the brake components.  This activity will remove the red rust on the brake rotors and prevent vehicle", "brake components.  This activity will remove the red rust on the brake rotors and prevent vehicle vibration when braking.  ENGINE FLUIDS AND LUBRICANTS CAUTION: Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant", "inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Note: If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.", "WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been", "the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it", "tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.", "To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument", "Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions", "must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote", "have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).", "the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset", "engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic", "before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote", "the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  To Accelerate For Passing While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is", "the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  Do not use in hilly terrain or with heavy loads.  When using the Cruise Control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.  Use Cruise Control in flat terrain and with light loads to maximize fuel efficiency.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d", "Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Recommended Distribution Hitch Adjustment An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  Outside Air Intake Make sure the air intake, located directly in front of the windshield, is free of", "Air Intake Make sure the air intake, located directly in front of the windshield, is free of obstructions, such as leaves.  Leaves collected in the air intake may reduce airflow, and if they enter the air distribution box, they could plug the water drains.  In Winter months, make sure the air intake is clear of ice, slush, and snow.", "Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines", "of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification", "call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L", "meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round", "fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  Open the fuel filler door.  Fuel Filler Door Remove the diesel fuel filler cap by rotating it counterclockwise.  Fuel and Diesel Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the vehicle with fuel.  When the nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel", "excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel filler door.  FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is", "provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  Caution: if the water in fuel indicator light remains on, do not start engine before you drain the water from the fuel filter(s) to avoid engine damage \"\u21e8draining fuel/water separator filter \u2014 diesel engine\" .  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most", "diesel engine\" .  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of", "or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using", "to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API", "3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).", "Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Uconnect 4C/4C NAV with 8.4-inch Display Uconnect 4C/4C NAV With 8.4-inch Display Automatic Climate Controls Uconnect 4C/4C NAV With 8.4-inch Display Touchscreen And Faceplate Buttons  Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  UCONNECT", "the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  UCONNECT VOICE RECOGNITION Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.", "Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To", "the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: for the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  The engine is allowed to crank as long as 25 seconds.  If the engine fails to start during this period, please wait at", "to crank as long as 25 seconds.  If the engine fails to start during this period, please wait at least two minutes for the starter to cool before repeating start procedure.  If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filters to avoid engine damage", "Fastener Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  To remove the Fastener Bin: Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Note: The soft top fasteners do not go in the Fastener Bin.  Rear Wall Storage Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  Fastener Bin Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Installing The Soft Top Install the belt rail on the rear of", "from the bottom of the Fastener Bin.  Installing The Soft Top Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque specification for torx fastener maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  Damage to the retainers will occur.  Step one 1 \u2014 corner fasteners 2 \u2014 rear fasteners install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Caution: failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the", "the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step four using the provided #t50 torx head driver and ratchet, install and tighten the torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step five torque specification for torx fasteners maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Step five before driving the vehicle with the top in the sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners.  Step Six Note:", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Closing The Hood To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.", "rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  WARNING: Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.", "What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to", "are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Wheel And Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Your wheels are susceptible to deterioration caused by salt, sodium chloride, magnesium chloride, calcium chloride, etc., and other road chemicals used to melt ice or control dust on dirt roads.  Use a soft", "etc., and other road chemicals used to melt ice or control dust on dirt roads.  Use a soft cloth or sponge and mild soap to wipe away promptly.  Do not use harsh chemicals or a stiff brush.  They can damage the wheel\u2019s protective coating that helps keep them from corroding and tarnishing.  When cleaning extremely dirty wheels, including excessive brake dust, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels.  Mopar\u00ae Wheel Treatment or Mopar\u00ae Chrome Cleaner, or their equivalent, is recommended or select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels.  CAUTION: Avoid products or automatic car washes that use acidic solutions or strong alkaline additives or harsh brushes.  Many aftermarket wheel cleaners and automatic car washes may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  CAUTION: Do not use", "Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  CAUTION: Do not use scouring pads, steel wool, a bristle brush, metal polishes, or oven cleaner.  These products may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  Note: If you intend parking or storing your vehicle for an extended period after cleaning the wheels with wheel cleaner, drive your vehicle and apply the brakes to remove the water droplets from the brake components.  This activity will remove the red rust on the brake rotors and prevent vehicle vibration when braking.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial", "tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such", "coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.", "Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the", "before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper", "and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait", "the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.", "Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat buildup may cause serious injury or death.  It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.  In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.  Be sure everyone in your vehicle is in a seat and using a seat belt properly.  60/40 Split Folding Rear Seat The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped)WARNING: The seatback is not intended to be used for storing cargo when folded flat, and only folds to allow access to the cargo area behind the", "for storing cargo when folded flat, and only folds to allow access to the cargo area behind the seat.  Do not operate the vehicle with unsecured cargo on the second row folded seatback.  Note: Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.  In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.  Be sure everyone in your vehicle is in a seat and using a seat belt properly.  The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to", "lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  This vehicle has front air bags and lap/shoulder belts for both the driver and front passenger.  The front air bags are a supplement to the seat belt restraint systems.  The driver front air bag is mounted in the center of the steering wheel.  The passenger front air bag is mounted in the instrument panel, above the glove compartment.  The words \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d are embossed on the air bag covers.  This vehicle has an Occupant Classification System (\u201cOCS\u201d) in the front passenger seat.  The OCS is designed to activate or deactivate the Passenger Advanced Front Air Bag depending on the occupant\u2019s seated weight.  It is designed to deactivate the Passenger Advanced Front Air Bag for an unoccupied seat and for occupants whose seated weight classifies them in a category other than a properly seated adult.  This could be a child, teenager, or even an adult.  Cargo must be", "than a properly seated adult.  This could be a child, teenager, or even an adult.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.", "Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To", "location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut", "To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.", "The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.", "160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to", "(with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Turn off the Fuel Filter Heater, Turn off the HVAC Blower Motor, Close the HVAC Circulation Door Cut off battery power to the: Engine Electric Motor (if equipped) Electric power steering Brake booster Electric park brake Automatic transmission gear selector Horn Front wiper  Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in", "be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or", "is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life", "plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Extreme Cold Weather The cartridge block heater clips into the", "authorized dealer) is recommended.  Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.", "SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey", "through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS", "in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s", "into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call,", "You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.  Sos call system limitations vehicles sold in mexico do not have sos call system capabilities.  SOS or other emergency line operators in Mexico may not answer or respond to SOS system calls.  If the SOS Call system detects a malfunction, any of the following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message", "buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d an in-vehicle audio message will state \u201cvehicle device requires service.  Please contact an authorized dealer.\u201d even if the sos call system is fully functional, factors beyond fca us llc\u2019s control may prevent or stop the sos call system operation.  These include, but are not limited to, the following factors: the ignition is in the off position the vehicle\u2019s electrical systems are not intact the sos call system software and/or hardware are damaged during a crash the vehicle battery loses power or becomes disconnected during a vehicle crash lte (voice/data) or 4g (data) network and/or global positioning satellite signals are unavailable or obstructed equipment malfunction at the sos operator facility operator error by the sos operator lte (voice/data) or 4g (data) network congestion weather buildings, structures, geographic terrain, or", "(voice/data) or 4g (data) network congestion weather buildings, structures, geographic terrain, or tunnels warning: ignoring the rearview mirror light could mean you will not have sos call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be", "to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber.  Never place anything on or near the vehicle\u2019s LTE (voice/data) or 4G (data) and GPS antennas.  You could prevent LTE (voice/data) or 4G (data) and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable LTE (voice/data) or 4G (data) network connection and a GPS signal is required for the SOS Call system to function properly.  Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press", "Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the", "km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam", "in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up", "trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  Front View Camera When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.", "ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be", "may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades seeCAUTION: Never use Non-Detergent Oil or", "occur.  For the recommended viscosity and quality grades seeCAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.", "Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety", "any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province,", "including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where", "Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html frequently asked questions about installing child restraints with seat belts what is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child", "anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward-facing child restraint, up to the recommended weight limit of the child restraint.  Can the rear-facing child restraint touch the back of the front passenger seat?  Yes contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.  Can the rear head restraints be removed?  Yes the center head restraint can be removed if it interferes with the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint?  No do not twist the buckle stalk in a seating position with an alr retractor.  Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the", "and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.  Use this simple 5-step test to decide whether the child can use the vehicle\u2019s seat belt alone: Can the child sit all the way back against the back of the vehicle seat?  Do the child\u2019s knees bend comfortably over the front of the vehicle seat while the child is still sitting all the way back?  Does the shoulder belt cross the child\u2019s shoulder between the neck and arm?  Is the lap part of the belt as low as possible, touching the child\u2019s thighs and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to any of these questions was \u201cno,\u201d then the child still needs to use a booster seat in this vehicle.  If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s squirming or slouching can move the belt out of position.  If the shoulder belt contacts the", "squirming or slouching can move the belt out of position.  If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.  WARNING: Never allow a child to put the shoulder belt under an arm or behind their back.  In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.  A child must always wear both the lap and shoulder portions of the seat belt correctly.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.", "is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  Vehicle info push and release the up or down arrow button until the vehicle info menu icon is displayed in the instrument cluster display.  Push and release the left or right arrow button to scroll through the information submenus and push and release the ok button to select or reset the resettable submenus.  Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become", "been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  When the Display button is pressed on the touchscreen, the system will display the options related to the theme (if equipped), brightness, and color of the touchscreen.  The available settings are: note: depending on the vehicle\u2019s options, feature settings may vary.  MAX A/C Button Press and release the MAX A/C button on the touchscreen to change the current setting to the coldest output of air.  MAX A/C sets the control for maximum cooling performance.  The MAX A/C indicator illuminates when MAX A/C is on.  Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.  Note: The MAX A/C button is only available on the touchscreen.", "Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after", "disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Maintenance-Free Battery Your vehicle is equipped with a", "wheel well for the front passenger wheel.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt", "the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If", "batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Closing The Hood To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.", "rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  WARNING: Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.", "In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance", "abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.", "API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to", "you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov .  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c.20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause", "an authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.", "ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the", "duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and", "climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Diesel Fuel Specifications This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for", "to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with", "for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  CAUTION: If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage  ENGINE", "NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty", "and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.", "To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independentlyBe sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped)  To fold the seat bottom upward, proceed as follows: The rear seat bottoms can be folded upward into the Stadium Position to create more storage space on the vehicle\u2019s floor, and to access the under seat storage bins (if equipped).  The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The", "60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped) Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Lift upward on each section of the seat bottom.  Lift From Beneath Seat (Left Side Shown) Raise the seat bottom upward into the Stadium Position.  60/40 Split Folding Rear Seat The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.", "The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped)WARNING: The seatback is not intended to be used for storing cargo when folded flat, and only folds to allow access to the cargo area behind the seat.  Do not operate the vehicle with unsecured cargo on the second row folded seatback.  Note: Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.  In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not", "seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.  Be sure everyone in your vehicle is in a seat and using a seat belt properly.", "If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire", "will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.", "while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across", "the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the gvwr \"\u21e8vehicle loading\" .  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating", "and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.", "Upper Door Adjustment After installation of the half-doors, if water leaks or wind noise is observed, the seal of the upper half-door to the door opening may need to be adjusted.  To determine if the upper half-door needs to be adjusted, proceed as follows: Determine which door is affected.  Open the affected door and hold a dollar-size piece of paper along the top of the door opening against the vehicle near where the leak/noise was observed.  Make sure half of the paper is above the area where the door seal contacts the door opening, while the other half is below.  Close the door on the paper, then pull the paper upward.  If the paper moves with little to no effort, the upper half-door will need to be adjusted in that area to increase seal compression.  Performing A Paper Test There is another optional test that can be performed using a flashlight and the help of another person.  One person should be inside the vehicle, and move the flashlight around the periphery of the door seal, shining outward.  The", "the vehicle, and move the flashlight around the periphery of the door seal, shining outward.  The other person should stand outside of the vehicle and check for light passing by the seal.  If light is seen through the seal area, the door will need to be adjusted.  To adjust the seal compression, proceed as follows: Open the door and lift the upper half-door up and away from the lower half.  Lay the upper half-door on a clean, dry surface.  Using an 8 mm open-end wrench (not provided), loosen the nut located inside the bottom of the upper half-door post, closest to where the \u201cpaper test\u201d detected a gap.  Nut location inside bottom of post using a 3 mm allen wrench (not provided), rotate the screw on the side of the post counterclockwise (while holding the wrench on the loosened bolt) to increase the seal compression.  If needed, rotate clockwise to reduce seal compression.  Rotate screw for seal compression 1 \u2014 3 mm allen wrench 2 \u2014 8 mm open-end wrench tighten the nut inside the bottom of the post using the", "3 mm allen wrench 2 \u2014 8 mm open-end wrench tighten the nut inside the bottom of the post using the wrench and make sure the screw head is flush to the post.  Reinstall the upper half-door.  Screw head flush to post close the door and repeat the \u201cpaper test\u201d.  Repeat the adjustment procedure if needed.  If needed, add the provided shim to a lower half-door pocket to seal the upper half-door to the roof: lift upper half-door up and away from lower half.  Clean the bottom of the door pocket.  Remove upper half-door & clean bottom of door pocket slide the shim onto a pencil or similar tool.  Remove the paper backing from the adhesive side of the shim and place the shim with pencil into the pocket.  Press the shim firmly to the bottom of the pocket, and remove the pencil once the shim is firmly in place.  Press shim firmly into bottom of pocket 1 \u2014 remove paper backing from shim 2 \u2014 slide pencil through hole in shim 3 \u2014 press pencil with shim into pocket replace upper half-door.  Note: If the compression is", "shim 3 \u2014 press pencil with shim into pocket replace upper half-door.  Note: If the compression is increased too much on the front upper corner of the rear doors, deformation of the seal will occur.  Half-Door Installation To install the front or rear half-doors, proceed as follows: Remove the full doors from the vehicle.  For front door removal, see For rear door removal, see Locate the upper and lower hinge pins on the lower half-door, and lower them into the body hinges on the vehicle.  Note: the upper hinge pin is longer, which can be used to assist in guiding the door into place during installation.  Lower half-door hinge pins insert the upper and lower hinge pin screws into the body hinges.  Tighten the screws using a #T50 Torx head driver to 3.8 ft\u00b7 lb / 5.2 N\u00b7m.  Caution: do not close the door before reattaching the door check to the body.  Damage may occur to the door check.  Do not overtighten Torx fasteners, damage to the vehicle\u2019s parts will occur.  Hinge pins can break if overtightened during", "fasteners, damage to the vehicle\u2019s parts will occur.  Hinge pins can break if overtightened during door install (Max Torque: 6.0 ft\u00b7 lb/8.1 N\u00b7m).  Attach the cloth strap of the lower half-door to the metal hook just inside the vehicle.  Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap connect the wiring harness on the lower half-door to the connection just inside the vehicle.  Note: for front doors, make sure the wiring harness is closed completely.  Front door wiring harness 1 \u2014 open wiring harness 2 \u2014 closed wiring harness replace wiring access doors.  When the half-doors are shipped with the vehicle, the lower half-doors will have plugs in the post holes that must be removed prior to upper half-door installation.  To remove these plugs, proceed as follows: locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place tool into service hole of plug to remove using the tool,", "recommended) in the service hole.  Place tool into service hole of plug to remove using the tool, slowly pull upwards from the center of the plug to remove.  Making sure the window on the upper half-door is completely zipped closed, insert the upper half-door into the lower half-door by placing the posts into the post holes.  Lower the upper half-door into post holes push down firmly on the inside of the upper half-door until it is fully seated in the lower half.  Push Down To Fully Seat Upper Half-Door  Half-doors \u2014 if equipped half-doors \u2014 if equipped \u00b9 use this qr code to access your digital experience.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  CAUTION: Do not run half-doors through an automatic car wash.  This may result in scratches and wax buildup on the windows.  Careless handling and storage of the half-doors may", "in scratches and wax buildup on the windows.  Careless handling and storage of the half-doors may damage the seals resulting in water leaks into the interior of the vehicle.  The upper half-doors must be positioned properly to ensure sealing.  Improper installation can cause water leaks into the interior of the vehicle.  Store the zipper pulls of the upper half-door windows at the upper B-pillar area for both front and rear doors to avoid damage to the windows when not in use.  Do not attempt to operate the half-door zipper in temperatures of 41\u00b0F (5\u00b0C) or below.  Damage to the window may occur.", "Off-Road Driving Tips  DRIVING TIPS Off-Road Driving Tips Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result", "features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.", "Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada).  Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage Owner's Manuals, Radio Manuals and Warranty Information Books can be ordered through Archway at: To order the following manuals, you may use either the website or the phone numbers listed below.  Owner's Manuals If you do not read the entire Owner\u2019s Manual, you may miss important information.  Observe all Cautions and Warnings.  Owner's Manuals These Owner's Manuals have been prepared with the assistance", "and Warnings.  Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada) symbols key if you do not read the entire owner\u2019s manual, you may miss important information.  Observe all Cautions and Warnings.  Service Manuals These comprehensive Service Manuals provide a complete working knowledge of the vehicle, system, and/or components and is written in straightforward language with illustrations, diagrams, and charts.", "To engage REVERSE gear from the NEUTRAL position, lift the REVERSE ring, located below the knob and move the gear selector all the way left and then forward.  If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  To shift the gears, fully press the clutch pedal and place the gear selector into the desired gear position (the diagram for the engagement of the gears is displayed on the handle of the selector).  The gear position will be displayed in the instrument cluster.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to", "front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  Yellow indicator lights 4wd indicator light \"\u21e84wd indicator light \u2014 if equipped\" 4wd low indicator light \"\u21e84wd low indicator light \u2014 if equipped\" 4wd part time indicator light \"\u21e84wd part time indicator light \u2014 if equipped\" axle locker fault indicator light \"\u21e8axle locker fault indicator light \u2014 if equipped\" rear axle lock indicator light \"\u21e8rear axle lock indicator light \u2014 if equipped\" front and rear axle lock indicator light \"\u21e8front and rear axle lock indicator light \u2014 if equipped\" forward collision warning off indicator light \"\u21e8forward collision warning off indicator light \u2014 if equipped\" neutral indicator light \"\u21e8neutral indicator light \u2014 if equipped\" sway bar indicator light \"\u21e8sway bar indicator light \u2014 if equipped\" off road+ indicator light \"\u21e8off road+ indicator light \u2014 if equipped\" cargo", "light \u2014 if equipped\" off road+ indicator light \"\u21e8off road+ indicator light \u2014 if equipped\" cargo light on indicator light \"\u21e8cargo light on indicator light\" wait to start indicator light \"\u21e8wait to start indicator light \u2014 if equipped\" low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \"\u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped\" water in fuel indicator light \"\u21e8water in fuel indicator light \u2014 if equipped\" selec speed control (ssc) indicator light \u2014 if equipped this light will turn on when selec speed control is activated.  Selec Speed Control is available in 4WD Low ONLY.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.", "Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a", "electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of", "and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Frequency Operated Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your", "To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.  FOBIK-Safe only executes in vehicles with Passive Entry.  There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made by a valid Passive Entry key fob while a door is open.  A lock request is made by the Passive Entry door handle while a door is open.  A lock request is made by the door panel switch while the door is open.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  Note: The vehicle will only unlock the doors", "described in this section remains active/functional.  Note: The vehicle will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle.  The vehicle will not unlock the doors when any of the following conditions are true: A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are manually locked using the door lock knobs.  Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.", "Transmission function is monitored electronically for abnormal conditions.  If a condition is detected that could result in transmission damage, Transmission Limp Home mode is activated.  In this mode, the transmission may operate only in certain gears, or may not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some situations, the transmission may not re-engage if the engine is turned off and restarted.  The Malfunction Indicator Light (MIL) may be illuminated.  A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary.  It is important to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only manufacturer's specified transmission fluid It is important to maintain the transmission fluid at the correct level using the recommended fluid.  Using a transmission fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission", "fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  Using a lower gear while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  This action will also provide better engine braking.  Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle When frequent transmission shifting occurs (such as when", "Towing For Towing A Disabled Vehicle When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing a heavy trailer), use the AutoStick shift control to select a lower gear Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to", "or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  During cold weather, you may experience increased effort in shifting until the transmission fluid warms up.  This is normal.  Routine fluid and filter changes are not required.  However, change the fluid and filter if the fluid becomes contaminated (with water, etc.  ), or if the transmission is disassembled for any reason.  Automatic Transmission \u2014 If Equipped  Transmission Limp Home Mode Transmission function is monitored electronically for abnormal conditions.  If a condition is detected that could result in transmission damage, Transmission Limp Home mode is activated.  In this mode, the transmission may operate only in certain gears, or may not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some", "not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some situations, the transmission may not re-engage if the engine is turned off and restarted.  The Malfunction Indicator Light (MIL) may be illuminated.  A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary.  In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following steps: Even if the transmission can be reset, we recommend that you visit an authorized dealer at your earliest possible convenience.  An authorized dealer has diagnostic equipment to assess the condition of your transmission.  If the transmission cannot be reset, authorized dealer service is required.  Stop the vehicle.  Shift the transmission into PARK, if possible.  If not, shift the transmission to NEUTRAL.  Push and hold the ENGINE START/STOP button until the engine turns off.  Wait approximately 30", "Push and hold the ENGINE START/STOP button until the engine turns off.  Wait approximately 30 seconds.  Restart the engine.  Shift into the desired gear range.  If the problem is no longer detected, the transmission will return to normal operation.  Note: In cases where the instrument cluster message indicates the transmission may not re-engage after engine shutdown, perform this procedure only in a desired location (preferably, at an authorized dealer).", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press", "Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the", "km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam", "in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD", "Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button", "is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an", "SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too", "gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat,", "the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce", "off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on,", "while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system", "vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.", "If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the", "parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  When the parking brake is applied", "illuminate, have the light inspected by an authorized dealer.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  If the headlights or parking lights are left on after the ignition is placed in the OFF position, the vehicle will chime when the driver\u2019s door is opened.  Vehicle parking brake is applied Stability event occurs Gear selector is moved out of DRIVE Engine overspeed occurs Clutch pedal is pressed (manual transmission only) Vehicle is operating at a low RPM (manual transmission only) Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before", "crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  release the parking brake  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.", "in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not", "properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on", "functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been", "a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.", "Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset", "section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main", "WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will", "Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely", "two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.", "instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If", "if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.", "may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or", "will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the", "when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the", "with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It", "a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel", "is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d,", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.", "Potential signs of vehicle overheating: Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant", "Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine", "heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four", "will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the", "Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It", "with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to", "with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you", "off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool;", "upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service", "To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security", "Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped)Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the", "armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open", "arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second", "action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.", "Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts", "Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners", "careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it", "bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  Bumper end caps are removable on steel bumpers only.  The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 Bolt #2 Remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be", "lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step Two 1 \u2014 Hex Bolt Cover Installed 2 \u2014 Hex Bolt Cover Removed Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step Six Secure the windshield by passing a cinch strap through", "tie-down bumpers (if equipped).  Step Six Secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Do Not Overtighten!  Damage to the windshield could result.  Open the fuel filler door.  Fuel Filler Door Remove the fuel cap by rotating it counterclockwise.  Fuel Filler Cap Fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is", "\"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if", "below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.", "Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery", "If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see", "both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a", "the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect,", "death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  The positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Your vehicle may be equipped with a secondary battery used", "a \u201cfast charger\u201d to provide starting.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not", "not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.", "In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L 4H The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only", "at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  4H This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.", "surfaced roads.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the", "components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.", "WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been", "the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that", "WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.", "Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.  Do not open or close the Sunrider\u00ae top while driving.  Operating the top while driving could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice", "according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the", "heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the", "pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.", "Off-Road Driving Tips  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.", "areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire", "match those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could", "than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw", "accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is", "center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.", "The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force", "equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of", "maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Anti-Lock Brake System (ABS) The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking", "time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the abs activates: abs motor noise or clicking sounds (you may continue to hear for a short time after the stop) brake pedal pulsations a slight drop of the brake pedal at the end of the stop note: the abs is designed to function with the original equipment manufacturer (oem) tires.  Modification may result in degraded ABS performance.  WARNING: The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of", "or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS", "user\u2019s safety or the safety of others.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Anti-Lock Brake System (ABS) Warning Light This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  If the ABS light remains on or turns on", "position and may stay on for as long as four seconds.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying", "help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  If the ABS Warning Light remains on or comes on while", "the likelihood of ABS activation(s).  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be", "can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  The ABS is designed to function with the Original Equipment Manufacturer (OEM) tires.  Modification may result in degraded", "function with the Original Equipment Manufacturer (OEM) tires.  Modification may result in degraded ABS performance.  Your vehicle is equipped with an advanced Electronic Brake Control (EBC) system.  This system includes Anti-Lock Brake System (ABS), Brake Assist System (BAS), Electronic Brake Force Distribution (EBD), Electronic Roll Mitigation (ERM), Electronic Stability Control (ESC), Hill Start Assist (HSA), and Traction Control System (TCS).  These systems work together to enhance both vehicle stability and control in various driving conditions.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn", "alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals:", "the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.", "minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system", "from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or", "(CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, see These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the", "Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeThis remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN", "disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish", "this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  When Remote Start is active, and the outside ambient temperature is 40\u00b0F (4.5\u00b0C) or below, the system will automatically activate front defrost for 15 minutes or less.  The time is dependent on the ambient temperature.  Once the timer expires, the system will automatically adjust the settings depending on ambient conditions.  See \u201cRemote Start Comfort Systems \u2014 If Equipped\u201d in the next section for detailed operation.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15", "Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.", "your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil", "to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no", "completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator", "within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To", "this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will", "(805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on", "system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water", "free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  CAUTION: If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage Diesel Fuel Specifications This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill", "diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces", "Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use", "or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low", "or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use", "diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We", "must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that", "Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  Open the fuel filler door.  Fuel Filler Door Remove the diesel fuel filler cap by rotating it counterclockwise.  Fuel and Diesel Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the vehicle with fuel.  When the nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel filler door.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or", "Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan", "For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel", "requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust", "the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to", "ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Safety Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.  WARNING: Improperly inflated tires are dangerous and can cause collisions.  Underinflation increases tire flexing and can result in overheating and tire failure.  Overinflation reduces a tire's ability to cushion shock.  Objects on the road and chuckholes can cause damage that result in tire failure.  Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.  Unequal tire pressures can cause steering problems.  You could lose control of your vehicle.  Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.  Always drive with each tire", "to the other can cause the vehicle to drift to the right or left.  Always drive with each tire inflated to the recommended cold tire inflation pressure.  Note: Unequal tire pressures from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure from side to side may cause the vehicle to drift left or right.  FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out", "vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.", "Crossing A Ravine, Gully, Ditch, Washout Or Rut When crossing a ravine, gully, ditch, washout or a large rut, the angled approach is the key to maintaining your vehicle's mobility.  Approach these obstacles at a 45-degree angle and let each tire go through the obstacle independently.  You need to use caution when crossing large obstacles with steep sides.  Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover.  If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires.  Use the removed dirt to fill the rut ahead of the turnout you just created.  You should now be able to drive out following the trench you just created at a 45-degree angle.  WARNING: There is an increased risk of rollover when crossing an obstacle, at any angle, with steep sides.  When crossing a ravine, gully, ditch, washout or a large rut, the angled approach is the key to maintaining your vehicle's mobility.", "washout or a large rut, the angled approach is the key to maintaining your vehicle's mobility.  Approach these obstacles at a 45-degree angle and let each tire go through the obstacle independently.  You need to use caution when crossing large obstacles with steep sides.  Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover.  If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires.  Use the removed dirt to fill the rut ahead of the turnout you just created.  You should now be able to drive out following the trench you just created at a 45-degree angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something", "rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION:", "abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.", "Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the", "form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited", "This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system", "of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use", "or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling,", "to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential seeBulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes", "Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Fuel Oxidation Stability \u2014 Must Use Fuel Within Six Months Of Manufacture Biodiesel fuel has poor oxidation stability which can result in long term storage problems.  Fuel produced to approved ASTM standards, if stored properly, provides for protection against fuel oxidation for up to six months.", "To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note:", "(NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Note: depending on the vehicle\u2019s options, feature settings may vary.  Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and", "Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the", "ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will", "the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC positionIf the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle", "is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.", "Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution", "of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of", "all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.", "The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Retrieve funnel from under the right rear seat.  Fuel Funnel Location Refueling Funnel Remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting Funnel Ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from", "an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Emergency Gas Can Refueling Most gas cans will not", "cause the clutch to overheat and cause a fire.  Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of", "or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  REFUELING IN EMERGENCY \u2013 IF EQUIPPED The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Note: In certain cold conditions, ice may prevent the fuel door from opening.  If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button.  Do not pry on the door.  Emergency Gas Can Refueling Most gas cans will not", "inside release button.  Do not pry on the door.  Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of", "or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)", "Redundant Air Bag Warning Light If a fault with the Air Bag Warning Light is detected, which could affect the Supplemental Restraint System (SRS), the Redundant Air Bag Warning Light will illuminate on the instrument panel.  The Redundant Air Bag Warning Light will stay on until the fault is cleared.  In addition, a single chime will sound to alert you that the Redundant Air Bag Warning Light has come on and a fault has been detected.  If the Redundant Air Bag Warning Light comes on intermittently or remains on while driving have an authorized dealer service the vehicle immediately.  See \"\u21e8air bag warning light\" for more information regarding the redundant air bag warning light.  The warning display will turn on indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an", "is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with", "dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  This warning light will illuminate when the Stop/Start system is not functioning properly and service is required.  Contact an authorized dealer for service.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is", "Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The Air Bag Warning Light will turn on for four to eight", "have the problem diagnosed and corrected.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Ignoring the Air Bag Warning Light in", "an authorized dealer service the air bag system immediately.  Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bags to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Placing an object on the floor under the front passenger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision.  Do not place any objects on the floor under the front passenger seat.  If there is a fault present in the OCS, both the PAD Indicator Light and the Air Bag Warning Light will illuminate to show that the Passenger Advanced Front Air Bag is deactivated.  Should this occur, the Passenger Advanced Front Air Bag will remain deactivated until the fault is cleared.  This indicates that you should take the vehicle to an authorized dealer for", "the fault is cleared.  This indicates that you should take the vehicle to an authorized dealer for service immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light will illuminate whenever the ocs is unable to classify the front passenger seat status.  A malfunction in the OCS may affect the operation of the air bag system.  If the air bag warning light does not come on, or stays on after you start the vehicle, or it comes on as you drive, take the vehicle to an authorized dealer for service immediately.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will", "switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.", "Fastener Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  To remove the Fastener Bin: Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Note: The soft top fasteners do not go in the Fastener Bin.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  To remove the Fastener Bin: Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Your vehicle is equipped with a", "Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  Remove the grommets under the front seat (one left and one right).  Carpet Split Then pull the carpet out, to the rear and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin (if equipped), by removing the four bolts that hold it to the floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then lift the assembly out from under the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear Retainers Remove carpet from the vehicle.  When reinstalling the carpet, perform these", "Rear Retainers Remove carpet from the vehicle.  When reinstalling the carpet, perform these steps in reverse order making sure that the carpet is tucked under the scuffs, B-pillar, console, and then refasten the grommets.  Inside the bin are three removable dividers to set up storage that works best for you.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  The rear wall netting can be accessed the same way as the rear wall storage bin.  If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  Rear Wall Storage Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of", "is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  Fastener Bin Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.", "Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Lowering the windshield before completing the", "windshield is raised prior to installing the tops.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center", "windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Raise the hood slightly, and place a hand palm-side down in the center of the", "the lifted position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Release both of the outside hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  1 \u2014 Pull For Windshield Washer 2 \u2014 Rotate For Wiper Operation 3 \u2014 Push Up For Mist The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.", "Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.  When TSC is functioning, the ESC Activation/Malfunction Indicator Light will flash, the engine power may be reduced, and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying.  TSC is disabled when the ESC system is in the \u201cPartial Off\u201d or \u201cFull Off\u201d modes.  Note: TSC cannot stop all trailers from swaying.  Always use caution when towing a trailer and follow the trailer tongue weight recommendations.  See \"\u21e8trailer towing\" for further information.  WARNING: If TSC activates while driving, slow the vehicle", "towing\" for further information.  WARNING: If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway.  Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To", "or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.", "Door Latch Alignment If the door does not center align between the latch and the striker, proceed as follows: Loosen (do not remove) the four bolts on the door hinges using the provided #T50 Torx head driver.  Hinge bolt locations with the bolts loose, hold the door in the almost closing position, and check that the latch and striker align.  With the latch and striker aligned, proceed to close the door softly and tighten the hinge bolts to 20.3 ft\u00b7 lb / 27.5 N\u00b7m (Max Torque: 27.3 ft\u00b7 lb / 37 N\u00b7m).  CAUTION: Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  Note: Only adjust the door to fit correctly against the striker.  DO NOT adjust the striker, as this could affect the positioning of the full door.  Upper Door Adjustment After installation of the half-doors, if water leaks or wind noise is observed, the seal", "Adjustment After installation of the half-doors, if water leaks or wind noise is observed, the seal of the upper half-door to the door opening may need to be adjusted.  To determine if the upper half-door needs to be adjusted, proceed as follows: Determine which door is affected.  Open the affected door and hold a dollar-size piece of paper along the top of the door opening against the vehicle near where the leak/noise was observed.  Make sure half of the paper is above the area where the door seal contacts the door opening, while the other half is below.  Close the door on the paper, then pull the paper upward.  If the paper moves with little to no effort, the upper half-door will need to be adjusted in that area to increase seal compression.  Performing A Paper Test There is another optional test that can be performed using a flashlight and the help of another person.  One person should be inside the vehicle, and move the flashlight around the periphery of the door seal, shining outward.  The other person", "and move the flashlight around the periphery of the door seal, shining outward.  The other person should stand outside of the vehicle and check for light passing by the seal.  If light is seen through the seal area, the door will need to be adjusted.  To adjust the seal compression, proceed as follows: Open the door and lift the upper half-door up and away from the lower half.  Lay the upper half-door on a clean, dry surface.  Using an 8 mm open-end wrench (not provided), loosen the nut located inside the bottom of the upper half-door post, closest to where the \u201cpaper test\u201d detected a gap.  Nut location inside bottom of post using a 3 mm allen wrench (not provided), rotate the screw on the side of the post counterclockwise (while holding the wrench on the loosened bolt) to increase the seal compression.  If needed, rotate clockwise to reduce seal compression.  Rotate screw for seal compression 1 \u2014 3 mm allen wrench 2 \u2014 8 mm open-end wrench tighten the nut inside the bottom of the post using the wrench and", "wrench 2 \u2014 8 mm open-end wrench tighten the nut inside the bottom of the post using the wrench and make sure the screw head is flush to the post.  Reinstall the upper half-door.  Screw head flush to post close the door and repeat the \u201cpaper test\u201d.  Repeat the adjustment procedure if needed.  If needed, add the provided shim to a lower half-door pocket to seal the upper half-door to the roof: lift upper half-door up and away from lower half.  Clean the bottom of the door pocket.  Remove upper half-door & clean bottom of door pocket slide the shim onto a pencil or similar tool.  Remove the paper backing from the adhesive side of the shim and place the shim with pencil into the pocket.  Press the shim firmly to the bottom of the pocket, and remove the pencil once the shim is firmly in place.  Press shim firmly into bottom of pocket 1 \u2014 remove paper backing from shim 2 \u2014 slide pencil through hole in shim 3 \u2014 press pencil with shim into pocket replace upper half-door.  Note: If the compression is increased too", "pencil with shim into pocket replace upper half-door.  Note: If the compression is increased too much on the front upper corner of the rear doors, deformation of the seal will occur.  Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  How To Engage The Automatic Locking Mode Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  This indicator will illuminate when a door is ajar/open and not fully closed.", "To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then, adjust it to the appropriate height using the adjustment button.  For information on child seat tether routing, see A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  Do not drive the vehicle without the rear seat head restraints", "the vehicle or occupying a seat.  Do not drive the vehicle without the rear seat head restraints installed while passengers are occupying the rear seat.  In a collision, people riding in this area without the head restraints installed are more likely to be seriously injured or killed.  A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate", "put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  To remove the center head restraint, raise it as far as it can go.  Then, push the adjustment button and the release button at the base of each post while pulling the head restraint up.  A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  To raise the head restraint, pull upward on the head restraint.  To lower the head restraint, push the adjustment button located on the base of the head restraint, and push downward on the head restraint.  The release button does not need to be pushed to adjust the head restraint.  Front Head Restraints", "The release button does not need to be pushed to adjust the head restraint.  Front Head Restraints To raise the head restraint, pull upward on the head restraint.  To lower the head restraint, push the adjustment button located on the base of the head restraint, and push downward on the head restraint.  The release button does not need to be pushed to adjust the head restraint.  To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  WARNING: A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the", "compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  Note: Do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head.", "Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.  If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill,", "hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you", "straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a", "at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.", "Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  Do Not Operate The Engine With Low Oil Pressure If the Low Oil Pressure Warning Light turns on while driving, stop the vehicle and shut down the engine as soon as", "Pressure Warning Light turns on while driving, stop the vehicle and shut down the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the lamp.  If the lamp is still illuminated, shut the engine off, contact an authorized dealer, and do not operate the vehicle until the cause is corrected.  If the lamp is no longer illuminated, the engine can be operated, but should be taken to an authorized dealer as soon as possible for further inspection.  Note: Do not operate the vehicle until the cause is corrected.  This light does not show how much oil is in the engine.  The engine oil level must be checked under the hood.  CAUTION: If oil pressure falls to less than normal readings, shut the engine off immediately.  Failure to do so could result in immediate and severe engine damage.  Checking Oil Level To ensure proper engine lubrication, the engine oil must be maintained at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best", "at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off.  Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.  There are four possible dipstick types: Crosshatched zone.  Crosshatched zone marked SAFE.  Crosshatched zone marked with MIN at the low end of the range and MAX at the high end of the range.  Crosshatched zone marked with dimples at the MIN and the MAX ends of the range.  Adding 1 qt (1 L) of oil when the reading is at the low end of the dipstick range will raise the oil level to the high end of the range marking.  Note: Always maintain the oil level within the crosshatch markings on the dipstick.  CAUTION: Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure.  This could damage your engine.  Warm up the engine before placing it under load.  Do not operate the engine at", "damage your engine.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  This warning light will illuminate, and a chime will sound, to indicate", "an authorized dealer.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do Not Operate The Engine With Low Oil Pressure If the Low Oil Pressure Warning Light turns on while driving, stop the vehicle and shut down the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the lamp.  If the lamp is still illuminated, shut the engine off, contact an authorized dealer,", "the lamp.  If the lamp is still illuminated, shut the engine off, contact an authorized dealer, and do not operate the vehicle until the cause is corrected.  If the lamp is no longer illuminated, the engine can be operated, but should be taken to an authorized dealer as soon as possible for further inspection.  Note: Do not operate the vehicle until the cause is corrected.  This light does not show how much oil is in the engine.  The engine oil level must be checked under the hood.  CAUTION: If oil pressure falls to less than normal readings, shut the engine off immediately.  Failure to do so could result in immediate and severe engine damage.", "This vehicle is equipped with an Intelligent Battery Sensor (IBS) to perform additional monitoring of the electrical system and status of the vehicle battery.  1 \u2014 Supplemental Negative Battery Cable 2 \u2014 Main Negative Battery Cable 3 \u2014 Main Negative Battery Terminal 4 \u2014 Intelligent Battery Sensor (IBS) In cases when the IBS detects charging system failure, or the vehicle battery conditions are deteriorating, electrical load reduction actions will take place to extend the driving time and distance of the vehicle.  This is done by reducing power to or turning off non-essential electrical loads.  Battery Saver On, Battery Saver Mode Message, And Electrical Load Reduction Actions (If Equipped) This vehicle is equipped with an Intelligent Battery Sensor (IBS) to perform additional monitoring of the electrical system and status of the vehicle battery.  In cases when the IBS detects charging system failure, or the vehicle battery conditions are deteriorating, electrical load reduction actions will take place to", "vehicle battery conditions are deteriorating, electrical load reduction actions will take place to extend the driving time and distance of the vehicle.  This is done by reducing power to or turning off non-essential electrical loads.  Load reduction is only active when the engine is running.  It will display a message if there is a risk of battery depletion to the point where the vehicle may stall due to lack of electrical supply, or will not restart after the current drive cycle.  When load reduction is activated, the message \u201cBattery Saver On Some Systems May Have Reduced Power\u201d will appear in the instrument cluster.  These messages indicate the vehicle battery has a low state of charge and continues to lose electrical charge at a rate that the charging system cannot sustain.  The electrical loads that may be switched off (if equipped), and vehicle functions which can be affected by load reduction: heated seat/vented seats/heated wheel rear defroster and heated mirrors hvac system 115 volt ac power", "seat/vented seats/heated wheel rear defroster and heated mirrors hvac system 115 volt ac power inverter system audio and telematics system loss of battery charge may indicate one or more of the following conditions: the charging system cannot deliver enough electrical power to the vehicle system because the electrical loads are larger than the capability of the charging system.  The charging system is still functioning properly.  Turning on all possible vehicle electrical loads (e.g.  HVAC to max settings, exterior and interior lights, overloaded power outlets +12 Volt, 115 Volt AC, USB ports) during certain driving conditions (city driving, towing, frequent stopping).  Installing options like additional lights, upfitter electrical accessories, audio systems, alarms and similar devices.  Unusual driving cycles (short trips separated by long parking periods).  The vehicle was parked for an extended period of time (weeks, months).  The battery was recently replaced and was not charged completely.  The battery", "(weeks, months).  The battery was recently replaced and was not charged completely.  The battery was discharged by an electrical load left on when the vehicle was parked.  The battery was used for an extended period with the engine not running to supply radio, lights, chargers, +12 Volt portable appliances like vacuum cleaners, game consoles and similar devices.  Note: The charging system is independent from load reduction.  The charging system performs a diagnostic on the charging system continuously.  If the battery charge warning light is on it may indicate a problem with the charging system \"\u21e8battery charge warning light\" .  The ACC screen may display once again if any ACC activity occurs, which may include any of the following: This feature will only activate when the following conditions are met: The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may", "Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: Once SSC is enabled it will activate automatically once the following conditions are met: The following conditions must be met in order for HSA to activate:", "AutoPark will engage when all of these conditions are met: AutoPark will be disabled when operating the vehicle in 4WD LOW.  Autopark will engage only when vehicle speed is 1.2 mph (1.9 km/h) or less.  AutoPark will be disabled when operating the vehicle in 4WD LOW.  The message \u201c autopark disabled \u201d will be displayed in the instrument cluster.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an", "could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer", "must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Opening The Hood Release both of the outside hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood", "hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Note: Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If", "of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.", "The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring Height (H) Attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the", "approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  Service Forward Collision Warning (FCW) Light \u2014 If Equipped This warning light will illuminate to indicate a fault in the Forward Collision Warning System.", "This warning light will illuminate to indicate a fault in the Forward Collision Warning System.  Contact an authorized dealer for service Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.", "Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  It is the owner's responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system, please contact an authorized dealer.  Mixing engine coolant types is not recommended and can result in cooling system damage.  If HOAT and OAT coolant are mixed in an emergency, have an authorized", "in cooling system damage.  If HOAT and OAT coolant are mixed in an emergency, have an authorized dealer drain, flush, and refill with OAT coolant (conforming to MS.90032) as soon as possible.  Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been", "compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and", "into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Please review these recommendations for using Organic Additive Technology (OAT) engine coolant that meets the requirements of the manufacturer Material Standard MS.90032.  When adding engine coolant (antifreeze): The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  The tongue weight of the trailer The weight of any other type of cargo or equipment put in or on your vehicle The weight of the driver", "weight of any other type of cargo or equipment put in or on your vehicle The weight of the driver and all passengers For further information on GAWRs, vehicle loading, and trailer towing, see If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OAT coolant (conforming to MS.90032).  It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the Run Flat mode.  Disposal Of Used Coolant Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  Selection Of Coolant For further information Note: Mixing of engine", "assistance immediately.  Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not", "with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  ENGINE FLUIDS AND LUBRICANTS CAUTION: Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer", "flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Note: If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT)", "Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.", "engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.", "Maintenance Plan Refer to the maintenance plan for the required maintenance intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to prevent premature wear.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Maintenance Plan \u2014 Diesel Fuel Up To B5 Biodiesel Refer to the Maintenance Plans for required maintenance.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly", "ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Drain And Refill For the proper maintenance intervals  Maintenance Plan \u2014 Diesel Fuel Up To B5 Biodiesel Refer to the Maintenance Plans for required maintenance.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Maintenance Plan Refer to the maintenance plan for the required maintenance intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to", "intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to prevent premature wear.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.", "1 \u2014 Power Distribution Center (Fuses) 6 \u2014 Brake Fluid Reservoir Cap 2 \u2014 Battery 7 \u2014 Engine Air Cleaner Filter 3 \u2014 Engine Oil Dipstick 8 \u2014 Power Steering Fluid Reservoir Cap 4 \u2014 Engine Oil Fill 9 \u2014 Washer Fluid Reservoir Cap 5 \u2014 Engine Coolant Pressure Cap 1 \u2014 Battery 6 \u2014 Power Distribution Center (Fuses) 2 \u2014 Engine Oil Fill 7 \u2014 Power Steering Reservoir Cap 3 \u2014 Coolant Pressure Reservoir Cap 8 \u2014 Engine Oil Dipstick 4 \u2014 Brake Fluid Reservoir Cap 9 \u2014 Engine Air Cleaner Filter 5 \u2014 Washer Fluid Reservoir Cap Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Adding Washer Fluid The fluid reservoir is located in the engine compartment.  Be sure to check the fluid level at regular intervals.  Fill the reservoir with windshield washer", "Be sure to check the fluid level at regular intervals.  Fill the reservoir with windshield washer solvent only (not radiator antifreeze).  When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades; this will help blade performance.  To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate.  This rating information can be found on most washer fluid containers.  WARNING: Commercial windshield washer solvents are flammable.  They could ignite and burn you.  Care must be exercised when filling or working around the washer solution.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the", "Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off CAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.", "driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds", "REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the", "colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The", "or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Electric Power Steering (EPS) Fault Warning Light This warning light will turn on when there's a fault with the EPS system WARNING: Continued operation with reduced assist could pose a safety risk to yourself and others.  Service should be obtained as soon as possible.", "Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require", "coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  It is the owner's responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.  Some vehicles require special tools to add coolant properly.  Failure to fill these", "is operated.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system, please contact an authorized dealer.  Mixing engine coolant types is not recommended and can result in cooling system damage.  If HOAT and OAT coolant are mixed in an emergency, have an authorized dealer drain, flush, and refill with OAT coolant (conforming to MS.90032) as soon as possible.  Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant", "emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is", "damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Please review these recommendations for using Organic Additive Technology (OAT) engine coolant", "Please review these recommendations for using Organic Additive Technology (OAT) engine coolant that meets the requirements of the manufacturer Material Standard MS.90032.  When adding engine coolant (antifreeze): The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  The tongue weight of the trailer The weight of any other type of cargo or equipment put in or on your vehicle The weight of the driver and all passengers For further information on GAWRs, vehicle loading, and trailer towing, see If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OAT coolant (conforming to MS.90032).  It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the Run Flat mode.  Disposal Of Used Coolant Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To", "Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant", "an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  ENGINE FLUIDS AND LUBRICANTS CAUTION: Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine", "coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Note: If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel", "to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.", "There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  To reinstall the door(s), perform the previous steps in the reverse order.  Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop", "is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  Prior to off-road usage, the side steps should be removed to prevent damage.  There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt", "nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly With the help of a second person, set the Sunrider\u00ae top onto the top of the vehicle making sure to align the holes at the front and rear of the side rails.  Lower Sunrider\u00ae Onto The Vehicle Swing the front frame bracket around the side of the rail, and insert the door rail attachment bolt (provided bolt without spacer) from underneath.  Tighten with a #40 Torx head driver until snug.  Attach Front Door Rail Bolt Insert the rear door rail attachment bolt (provided bolt with spacer) from underneath.  Tighten with #40 Torx head driver until snug.  Attach Rear Door Rail Bolt Repeat", "from underneath.  Tighten with #40 Torx head driver until snug.  Attach Rear Door Rail Bolt Repeat steps 3 and 4 on the other side of the vehicle.  The recommended torque specification for the front and rear door rail attachment bolts is 8.8 ft-lb (12 N\u00b7m).  Attach the rear clamp at the rear center of the Sunrider\u00ae top using the two provided rear clamp attachment bolts.  Tighten with #40 Torx head driver until snug.  Rear Clamp Location The recommended torque specification for the rear clamp attachment bolts is 3.7 ft-lb (5 N\u00b7m).  From inside the vehicle, lift and pull the Sunrider\u00ae top forward using the integrated handle on the front header of the top.  Manually guide the top into the closed position.  Push Sunrider\u00ae Top Forward From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Pull the handle back upward while squeezing the hook, locking the latch into place.  Repeat on the other side.  Engage Both Header Latches Lug Nut/Bolt Torque **Lug Nut/Bolt", "place.  Repeat on the other side.  Engage Both Header Latches Lug Nut/Bolt Torque **Lug Nut/Bolt Size Lug Nut/Bolt Socket Size 130 ft-lb (176 N\u00b7m) M14 x 1.50 mm 22 mm After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  Side Step Removal \u2014 If Equipped There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener locations (one side) remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side", "Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side steps should be removed to prevent damage.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying", "this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced", "a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly", "not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.", "securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  External racks do not increase the total load carrying capacity of the vehicle.  Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, does not exceed the maximum vehicle load capacity.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full", "operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred,", "will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.", "operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped)Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a", "arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately", "Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.", "A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into", "the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Press and release this button to turn the Climate Control ON/OFF.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  To Turn Off The Engine Using The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C", "The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control will turn off, but Stability Control will remain active.  Hold the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner", "the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  A/C Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Note: For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the", "seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.", "Jack Location The jack and tools are stored under the right rear seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat.  Removing the wing bolt release the tool bag straps from the jack and remove tools from bag.  Jack and tool bag remove tool kit and assemble tools.  Jack And Tool Bag There are two ways to assemble the tools: Note: If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  CAUTION: The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools,", "and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools, always reinstall them in the original carrier and location.  While driving you may experience abrupt stopping, rapid acceleration or sharp turns.  A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an", "being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Side Step Removal \u2014 If Equipped There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener locations (one side) remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and", "each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side steps should be removed to prevent damage.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.", "lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.", "Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates", "and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs", "needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android", "the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its", "calls.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To", "Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the", "your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc. Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .", "Push and release the up or down arrow button until the fuel economy icon is highlighted in the instrument cluster display.  Push and hold the ok button to reset average fuel economy feature.  Toggle left or right to select a display with or without current fuel economy information.  Fuel Economy The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located  Vehicle info push and release the up or down arrow button until the vehicle info menu icon is displayed in the instrument cluster display.  Push and release the left or right arrow button to scroll through the information submenus and push and release the ok button to select or reset the resettable submenus.  The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is locatedSee the following", "symbol points to the side of the vehicle where the fuel filler door is locatedSee the following steps for refueling: If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a", "See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the", "Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can", "lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  To Reset The Manual Park Release: Pull upward on the tether strap, releasing it from the \u201clocked\u201d position.  Lower the Manual Park Release lever downward into its original position.  Original tether position tuck the tether strap into the base of the", "into its original position.  Original tether position tuck the tether strap into the base of the console, and reinstall the cover.  Extended Park Starting Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Note: Extended Park condition occurs when the vehicle has not been started or driven for at least 30 days.  CAUTION: To prevent damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.", "Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When", "if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so", "in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being", "be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx", "the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  60/40 Split Folding Rear Seat The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped)WARNING: The seatback is not intended to be used for storing cargo when folded flat, and only folds to allow access to the cargo area behind the seat.  Do not operate the vehicle with unsecured cargo on", "allow access to the cargo area behind the seat.  Do not operate the vehicle with unsecured cargo on the second row folded seatback.  Note: Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.  In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.  Be sure everyone in your vehicle is in a seat and using a seat belt properly.  The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  This vehicle has", "seatback.  Both seatbacks should be locked to limit access to items behind seat.  This vehicle has front air bags and lap/shoulder belts for both the driver and front passenger.  The front air bags are a supplement to the seat belt restraint systems.  The driver front air bag is mounted in the center of the steering wheel.  The passenger front air bag is mounted in the instrument panel, above the glove compartment.  The words \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d are embossed on the air bag covers.  This vehicle has an Occupant Classification System (\u201cOCS\u201d) in the front passenger seat.  The OCS is designed to activate or deactivate the Passenger Advanced Front Air Bag depending on the occupant\u2019s seated weight.  It is designed to deactivate the Passenger Advanced Front Air Bag for an unoccupied seat and for occupants whose seated weight classifies them in a category other than a properly seated adult.  This could be a child, teenager, or even an adult.  Cargo must be securely tied down before driving your vehicle.", "child, teenager, or even an adult.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.", "Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact", "background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected,", "will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to", "hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect", "two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.", "in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.", "PARKING BRAKE Before exiting the vehicle, make sure that the parking brake is fully applied.  Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or FIRST gear.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic", "to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  WARNING: Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake", "be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  CAUTION: If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the", "as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit", "could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally", "unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  When the parking brake is", "and fill as needed.  Check function of all interior and exterior lights.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the Brake Warning Light", "or that there is a problem with the Anti-Lock Brake System reservoir.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.", "ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are", "in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the", "starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:", "Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also", "under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  Bed Rail Tie Down Locations Your vehicle is equipped with the child restraint", "in the truck bed.  Bed Rail Tie Down Locations Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.  The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer", "provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Supplemental Seat-Mounted Side Air Bags (SABs) are located in the outboard side of the front seats.  The SABs are marked with a \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d on a label or on the seat trim on the outboard side of the seats.  Four auxiliary switches are located in the lower switch bank of the instrument panel and can be used to power various electrical devices.  1 \u2014 Retainers 2 \u2014 Fuel Filter Protective Cover The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.", "Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Maps Push and hold the VR button on the steering wheel until the beep or tap the Microphone icon to ask Apple\u00ae Siri to take you to a desired destination by voice.  You can also touch the", "icon to ask Apple\u00ae Siri to take you to a desired destination by voice.  You can also touch the Navigation icon in Apple CarPlay\u00ae to access Apple\u00ae Maps.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the", "to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the", "touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.", "To fold the seat bottom upward, proceed as follows: The rear seat bottoms can be folded upward into the Stadium Position to create more storage space on the vehicle\u2019s floor, and to access the under seat storage bins (if equipped).  The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped) Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Lift upward on each section of the seat", "the folded webbing and the seat belt is no longer twisted.  Lift upward on each section of the seat bottom.  Lift From Beneath Seat (Left Side Shown) Raise the seat bottom upward into the Stadium Position.  Rear Seat Stadium Position The rear seat bottoms can be folded upward into the Stadium Position to create more storage space on the vehicle\u2019s floor, and to access the under seat storage bins (if equipped).  To fold the seat bottom upward, proceed as follows: Lift upward on each section of the seat bottom.  Lift from beneath seat (left side shown) raise the seat bottom upward into the stadium position.  Stadium Position To return the seat bottom to the normal position, push downward on the raised seat bottom.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independentlyBe sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The", "are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped)", "If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.", "tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for", "Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons", "Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed", "is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from", "Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  Towing Requirements To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended: WARNING: Improper towing can lead to a collision.  Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel.  When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.  You could lose control of your vehicle and have a collision.  When hauling cargo, or towing a trailer, do not overload your vehicle or trailer.  Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or", "or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.  Safety chains must always be used between your vehicle and trailer.  Always connect the chains to the frame or hook retainers of the vehicle hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be parked on a grade.  When parking, apply the parking brake on the tow vehicle.  Put the tow vehicle transmission in PARK.  Always block or \"chock\" the trailer wheels.  GCWR must not be exceeded.  Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: gvwr gtw gawr tongue weight rating for the trailer hitch utilized caution: do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven.  The engine, axle or other parts could be damaged.  Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do", "the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.  This helps the engine and other parts of the vehicle wear in at the heavier loads.", "Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW", "temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring Height (H) Attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Trailer And Tongue Weight Never exceed the maximum tongue weight stamped on your bumper or trailer hitch.  Consider the following items when computing the weight on the", "on your bumper or trailer hitch.  Consider the following items when computing the weight on the rear axle of the vehicle: the tongue weight of the trailer the weight of any other type of cargo or equipment put in or on your vehicle the weight of the driver and all passengers note: remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.", "BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load", "cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from", "The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.", "The BSM system notifies the driver of objects in the detection zones by illuminating the BSM Warning Light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume.  See \"\u21e8blind spot modes\" for further information.  The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.  The BSM system will issue an alert during these types of zone entries.  When the BSM system is turned off there will be no visual or audible alerts from either the BSM or RCP systems.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft", "12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft (3 m) beyond the rear fascia/bumper of the vehicle.  The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas.  BSM Radar Location (Left Side Shown) The BSM system will store the current operating mode when the vehicle is shut off.  Each time the vehicle is started the previously stored mode will be recalled and used.  Blind Spot Monitoring (BSM) \u2014 If Equipped The BSM system uses two radar sensors, located inside the taillights, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.)  that enter the blind spot zones from the rear/front/side of the vehicle.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate", "mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft (3 m) beyond the rear fascia/bumper of the vehicle.  The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas.  The BSM system can become blocked if snow, ice, mud, or other road contaminations accumulate on the rear fascia/bumper where the radar sensors are located.  The system may also detect a blockage if the vehicle is operated in areas with extremely low radar returns, such as a desert, or parallel to a large elevation drop.  If a blockage is detected, a \u201cBlind Spot Temporarily Unavailable, Wipe Rear Corners\u201d message will display in the instrument", "a \u201cBlind Spot Temporarily Unavailable, Wipe Rear Corners\u201d message will display in the instrument cluster, both mirror lights will illuminate, and BSM and RCP alerts will be disabled.  This is normal operation.  The system will automatically resume function when the condition clears.  To minimize system blockage, do not block the area of the rear fascia/bumper where the radar sensors are located with foreign objects (bumper stickers, bicycle racks, etc.)  and keep it clear of road contaminations.  The BSM system notifies the driver of objects in the detection zones by illuminating the BSM Warning Light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume.  See \"\u21e8blind spot modes\" for further information.  The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.  The BSM system will issue an alert during these types of zone entries.  Note: The BSM system DOES NOT alert", "system will issue an alert during these types of zone entries.  Note: The BSM system DOES NOT alert the driver about rapidly approaching vehicles that are outside the detection zones.  The BSM system detection zone DOES NOT change if your vehicle is towing a trailer.  Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change.  If the trailer or other object (i.e., bicycle, sports equipment) extends beyond the side of your vehicle, this may result in the BSM Warning Light remaining illuminated the entire time the vehicle is in a forward gear.  See \"\u21e8uconnect settings\" for more information.  The Blind Spot Monitoring (BSM) system may experience dropouts (blinking on and off) of the side mirror warning indicator lights when a motorcycle or any small object remains at the side of the vehicle for extended periods of time (more than a couple of seconds).  ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster", "ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster displayIt provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.", "Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New", "and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage.", "accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet", "plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of", "vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Power Inverters \u2014 If Equipped There is a 115 V (400 W) maximum inverter outlet located on the back of the center console to convert Direct Current (DC) to Alternating Current (AC).  This outlet can power cellular phones, electronics and other low power devices requiring power up to 400 W. Certain video game consoles exceed this power limit, as will most power tools.  There may also be a second 115 V (400 W) maximum exterior power inverter located on the rear right side of the truck bed near the tailgate.  This inverter can be turned on by the Instrument Panel Power Inverter switch located to the left of the steering wheel.  This inverter can power cellular phones, electronics and other low power devices requiring power up to 400 W. Certain video game consoles exceed this limit, as will most power tools.  The", "power up to 400 W. Certain video game consoles exceed this limit, as will most power tools.  The indicator light on the power inverter switch will be illuminated when the inverter is turned on.  The power inverter is designed with built-in overload protection.  If the power rating of 400 W is exceeded, the power inverter automatically shuts down.  Once the electrical device has been removed from the outlet, the inverter should automatically reset.  Note: 400 W is the maximum for the inverter, not each outlet.  If two outlets are in use, 400 W is shared among the devices plugged in.  Note: The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  There", "when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners,", "the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.", "Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather.  To clear the windows, select Defrost or Mix mode and increase the front blower speed.  Do not use the Recirculation mode without A/C for long periods, as fogging may occur.  Do not use abrasive cleaning components, solvents, steel wool, or other aggressive material to clean the lenses.  The lenses in front of the instruments in this vehicle are molded in clear plastic.  When cleaning the lenses, care must be taken to avoid scratching the plastic.  Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as", "the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsTo minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.  To remove road dirt, wash with a mild soap solution followed by rinsing.  If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  If the \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the windshield and forward-facing camera inspected at an authorized dealer.", "obstruction, have the windshield and forward-facing camera inspected at an authorized dealer.  All glass surfaces should be cleaned on a regular basis with Mopar\u00ae Glass Cleaner, or any commercial household-type glass cleaner.  Never use an abrasive type cleaner.  Use caution when cleaning the inside rear window equipped with electric defrosters or windows equipped with radio antennas.  Do not use scrapers or other sharp instruments that may scratch the elements.  The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems are experienced.  This inspection should include the following points:  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer", "activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.", "Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the", "start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon", "the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Your vehicle is equipped with a sophisticated Onboard Diagnostic", "prevent vehicle registration.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will", "to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following:", "To Manually Turn On The Stop/Start System Push the Stop/Start Off switch (located on the switch bank).  The light on the switch will turn off.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the", "time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabledNote: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn On The Stop/Start System Push the Stop/Start Off switch (located on the switch bank).  The light on the switch will turn off.", "If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD", "(ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each", "braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot", "afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  The ABS is designed to function with the Original Equipment Manufacturer (OEM) tires.  Modification may result in degraded ABS performance.  Your vehicle is equipped with an advanced Electronic Brake Control (EBC) system.  This system includes Anti-Lock Brake System (ABS), Brake Assist System (BAS), Electronic Brake Force Distribution (EBD), Electronic Roll Mitigation (ERM), Electronic Stability Control (ESC), Hill Start Assist (HSA), and Traction Control System (TCS).  These systems work together to enhance both vehicle stability and control in various driving conditions.  The ABS is activated during braking when", "stability and control in various driving conditions.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS)", "may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency", "vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Anti-Lock Brake System (ABS) The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.", "cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the abs activates: abs motor noise or clicking sounds (you may continue to hear for a short time after the stop) brake pedal pulsations a slight drop of the brake pedal at the end of the stop note: the abs is designed to function with the original equipment manufacturer (oem) tires.  Modification may result in degraded ABS performance.  WARNING: The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting", "may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of", "in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Anti-Lock Brake System (ABS) Warning Light This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long", "on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.", "Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may", "the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap", "pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED) Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil", "as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause", "change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.", "law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in", "If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will", "Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact", "(UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "Emergency Tow Hooks \u2014 If Equipped If your vehicle is equipped with tow hooks, they are mounted in the front and the rear fascia/bumpers.  Note: Depending on vehicle trim level, rear tow hooks may vary.  WARNING: Do not use a chain for freeing a stuck vehicle.  Chains may break, causing serious injury or death.  Stand clear of vehicles when pulling with tow hooks.  Tow straps may become disengaged, causing serious injury.  CAUTION: Tow hooks are for emergency use only, to rescue a vehicle stranded off road.  Tow straps are recommended when towing the vehicle, chains may cause vehicle damage.  The tow hooks must not be used to move the vehicle off the road or where there are obstacles.  Do not use the tow hooks for tow truck hookup or highway towing.  Do not use the tow hooks to pull a vehicle onto a flatbed truck.  Do not use the tow hooks to free a stuck vehicle Damage to your vehicle may occur if these guidelines are not followed Manual Front Seatback Recline Adjustment To recline the seat, pull on the", "are not followed Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Rear Wall Storage Bin To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  Note: The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  To Reset The Manual Park Release: Pull upward on the tether strap, releasing it from the", "seat.  To Reset The Manual Park Release: Pull upward on the tether strap, releasing it from the \u201clocked\u201d position.  Lower the Manual Park Release lever downward into its original position.  Original tether position tuck the tether strap into the base of the console, and reinstall the cover.", "To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired", "times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide", "retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.", "VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both", "the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the", "If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your", "involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm", "one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system", "is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door.  Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.  Inflation pressure is measured in units of PSI (pounds per square inch) or kPa (kilopascals).  Maximum inflation pressure the maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire.  The maximum inflation pressure is molded into the sidewall.  Recommended cold tire inflation pressure the manufacturer\u2019s recommended cold tire inflation pressure as shown on the tire placard.  Tire placard a label permanently attached to the vehicle describing the vehicle\u2019s loading capacity, the original equipment tire sizes and the recommended cold tire inflation pressures.  Tire pressures change by approximately 1 psi (7 kPa) per 12\u00b0F (7\u00b0C)", "cold tire inflation pressures.  Tire pressures change by approximately 1 psi (7 kPa) per 12\u00b0F (7\u00b0C) of air temperature change.  Keep this in mind when checking tire pressure inside a garage, especially in the Winter.  Jacking and tire changing \u00b9 use this qr code to access your digital experience.  Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: At Every Oil Change Interval As Indicated By Oil Change Indicator System: Change oil and filter.  Rotate the tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on.  Inspect battery and clean and tighten terminals as required.  Inspect the CV/Universal joints.  Inspect brake pads, shoes, rotors, drums, hoses and parking brake.  Inspect engine cooling system protection and hoses.  Inspect exhaust system.  Inspect engine air cleaner filter if using in dusty or off-road conditions, replace engine air cleaner filter if necessary.  Inspect all door latches for presence", "conditions, replace engine air cleaner filter if necessary.  Inspect all door latches for presence of grease, reapply if necessary.  Do not continue driving with one or more flat tires as handling may be compromised.  Stop the vehicle, avoiding sharp braking and steering.  If a tire puncture occurs, repair immediately using the dedicated tire repair kit and contact an authorized dealer as soon as possible.  Consult an authorized tire dealer for tire repairs and additional information.  In the Selectable Tire Fill Alert application, which is located in the apps menu of the Uconnect system, you will be able to select a pressure setting for both the front and rear axle tire pressures by scrolling through a pressure range from XX to 15 psi in 1 psi increments for each axle setting.  After inspecting or adjusting the tire pressure, always reinstall the valve stem cap.  This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.  Check the inflation pressure of each tire,", "the valve stem, which could damage the valve stem.  Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.  Safety Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.  WARNING: Improperly inflated tires are dangerous and can cause collisions.  Underinflation increases tire flexing and can result in overheating and tire failure.  Overinflation reduces a tire's ability to cushion shock.  Objects on the road and chuckholes can cause damage that result in tire failure.  Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.  Unequal tire pressures can cause steering problems.  You could lose control of your vehicle.  Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.", "from one side of the vehicle to the other can cause the vehicle to drift to the right or left.  Always drive with each tire inflated to the recommended cold tire inflation pressure.  Note: Unequal tire pressures from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure from side to side may cause the vehicle to drift left or right.  FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of", "Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.", "Turn Signal Indicator Lights When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Note: A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.  Check for an inoperative outside light bulb if either indicator flashes at a rapid rate.  When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Lightly push the multifunction lever up or down, without moving beyond the", "the horn will chirp.  Lightly push the multifunction lever up or down, without moving beyond the detent, and the turn signal will flash three times then automatically turn off.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Turn Signal Indicator Lights When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Note: A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.  Check for an inoperative outside light bulb if either indicator flashes at a rapid rate.  Turn Signals Move the multifunction lever up or down to activate the turn signals.  The arrows on", "Turn Signals Move the multifunction lever up or down to activate the turn signals.  The arrows on each side of the instrument cluster flash to show proper operation.  Note: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.", "When activated, OFF ROAD+ is designed to improve the user experience when using specific Off Road driving modes.  To activate Off Road+, push the OFF ROAD+ switch in the switch bank.  The vehicle\u2019s performance will improve depending on which Four-Wheel Drive (4WD) mode is activated.  OFF ROAD+ Switch If equipped with Off Road+ and if Off Road+ is active when \"Full Off\" mode is enabled by the driver, ESC will not switch to \"Partial Off\" mode at any speed and will remain in \"Full Off\" mode until Off Road+ is exited or ESC is re-enabled by the driver.  OFF ROAD+ \u2014 If Equipped When activated, OFF ROAD+ is designed to improve the user experience when using specific Off Road driving modes.  To activate Off Road+, push the OFF ROAD+ switch in the switch bank.  The vehicle\u2019s performance will improve depending on which Four-Wheel Drive (4WD) mode is activated.  When off road+ is active, the following features will activate: the off road+ telltale will illuminate in the instrument cluster display a mode specific", "activate: the off road+ telltale will illuminate in the instrument cluster display a mode specific message will display the instrument cluster display off road pages will launch on the radio head-unit (if equipped) the off road camera will launch (if equipped) once in off road+, the vehicle will begin to behave in different ways depending on the 4wd mode in use.  The following enhancements will occur when using OFF ROAD+.  Note: OFF ROAD+ will not function in Two-Wheel Drive High (2H) mode.  If the button is pushed while in 2H mode, the cluster display will show the message \u201cOFF ROAD+ Unavailable Shift to 4WD\u201d.  Off Road+ Indicator Light \u2014 If Equipped This indicator light will illuminate when Off Road+ has been activated.", "Hill Climbing Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches", "trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of", "more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside", "ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all", "preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls,", "Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a", "brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using", "stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the", "or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire", "will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to", "top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to", "so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx", "the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Editing Your Notifications Notifications are an important element of your SiriusXM Guardian\u2122 account.  For example, any time you use your remote services (such as Remote Door Unlock), you can elect to receive a text message, push notification, and/or E-mail to notify you of the event.  To set up the notifications, please follow these instructions.  Log on to your owner\u2019s account at https://www.mopar.com/en-us.html (us residents) and select \u201cdashboard\u201d, or www.mopar.ca (canadian residents), select \u201cmy vehicle\u201d and then \u201cdashboard\u201d.  Click the Edit/Edit Profile button.  Once there, select \u201cSiriusXM Guardian\u2122\u201d where you can edit Notification Preferences.  You can enter a mobile phone and/or email address to notify you, and you can customize the types of messages.  Favorites Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  You can exit the Favorites Menu by a press of the X button.  The Favorites feature enables", "You can exit the Favorites Menu by a press of the X button.  The Favorites feature enables you to set a favorite artist or song that is currently playing.  The radio then uses this information to alert you when either the favorite artist or song is being played at any time by any of the SiriusXM\u00ae Channels.  The maximum number of favorites that can be stored in the Radio is 50.  Favorite artist: while the song is playing, to set a favorite artist, press the favorites button on the touchscreen and then the favorite artist button on the touchscreen.  Favorite song: while the song is playing, to set a favorite song, press the favorites button on the touchscreen and then the favorite song button on the touchscreen.  Using your owner\u2019s site your owner\u2019s site website https://www.mopar.com/en-us.html (us residents), or www.mopar.ca (canadian residents) provides you with all the information you need, all in one place.  You can track your service history, find recommended accessories for your vehicle, watch videos", "You can track your service history, find recommended accessories for your vehicle, watch videos about your vehicle's features, and easily access your manuals.  It is also where you can manage your SiriusXM Guardian\u2122 account.  This section will familiarize you with the key elements of the website that will help you get the most of your SiriusXM Guardian\u2122 connected services.  For customers in the United States, press the Sign In/Register button and enter your email address and password.  For customers in Canada, press the My Vehicle button.  Select from \u201cDashboard\u201d, \u201cVehicle Health Report\u201d, and \u201cRecalls\u201d.  The website will then prompt you to log in using your email address and password.  Edit/edit profile: to manage the details of your siriusxm guardian\u2122 account, such as your contact information, password and siriusxm guardian\u2122 pin, click on the edit/edit profile button to access the details of your account.  Connected services status: this statement will indicate your siriusxm guardian\u2122-equipped vehicle.", "Connected services status: this statement will indicate your siriusxm guardian\u2122-equipped vehicle.  Remote commands: for vehicles with an active siriusxm guardian\u2122 subscription, press one of these icons and enter your four-digit siriusxm guardian\u2122 security pin to remotely start (if equipped), lock/unlock doors or sound the horn and flash the lights.", "This is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer.  They want to know if you need assistance.  If an authorized dealer is unable to resolve the concern, you may contact FCA US LLC's Customer Assistance center.  FCA US LLC and its authorized dealers are vitally interested in your satisfaction.  We want you to be happy with our products and services.  Warranty service must be done by an authorized dealer.  We strongly recommend that you take the vehicle to an authorized dealer.  They know your vehicle the best, and are most concerned that you get prompt and high quality service.  FCA US LLC's authorized dealers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner.  This is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason", "is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer.  They want to know if you need assistance.  If an authorized dealer is unable to resolve the concern, you may contact FCA US LLC's Customer Assistance center.  We recommend seeing an authorized dealer for service.  An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  If the transmission cannot be reset, authorized dealer service is required.  WARRANTY INFORMATION See the Warranty Information for the terms and provisions of FCA US LLC warranties applicable to this vehicle and market.  Refer to www.mopar.com/om for further information.  See the Warranty Information for", "and market.  Refer to www.mopar.com/om for further information.  See the Warranty Information for the terms and provisions of FCA Canada Inc.warranties applicable to this vehicle and market.  Refer to www.owners.mopar.ca/en for further information.  Use this QR code to access your digital experience.", "Snow Tires Some areas of the country require the use of snow tires during the Winter.  Snow tires can be identified by a \u201cmountain/snowflake\u201d symbol on the tire sidewall.  If you need snow tires, select tires that are equivalent in size and type to the original equipment tires.  Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle.  Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h).  For speeds above 75 mph (120 km/h), refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures.  While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires.  Some states prohibit studded tires; therefore, local laws should be checked before using these tire types.  When stuck in mud, sand,", "therefore, local laws should be checked before using these tire types.  When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles", "is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your", "to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious", "when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.", "Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Biodiesel fuel may gel or solidify at low ambient temperatures, which may pose problems for both storage and operation.  Precautions can be necessary at low ambient temperatures, such as storing the fuel in a heated building or a heated storage tank, or using cold temperature additives.  Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Materials Added To Fuel Besides using", "economy, reduce emissions, and maintain vehicle performance.  Materials Added To Fuel Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Designated TOP TIER Detergent Gasoline contains a higher level of detergents to further aide in minimizing engine and fuel system deposits.  When available, the usage of TOP TIER Detergent Gasoline is recommended.  Visit www.toptiergas.com for a list of top tier detergent gasoline retailers.  Indiscriminate use of fuel system cleaning agents should be avoided.  Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients.  These can harm fuel system gasket and diaphragm materials.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline", "CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against", "tampering with the emissions control system can result in civil penalties being assessed against you.", "Secondary Method For Oil Change Reset Procedure Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Note: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.  If necessary, repeat this procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will", "may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the", "will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Secondary Method For Oil Change Reset Procedure Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Note: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.  If necessary, repeat this procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator", "in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil", "oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.", "your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil", "to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no", "completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator", "within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To", "this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will", "(805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on", "system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to", "of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances", "(if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle", "repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio.  This condition may be", "on in your vehicle can cause erratic or noisy performance from your radio.  This condition may be lessened or eliminated by repositioning the mobile phone within the vehicle.  This condition is not harmful to the radio.  If your radio performance does not satisfactorily improve from repositioning the mobile phone, it is recommended that the volume be turned down or off during mobile phone operation when not using the Uconnect system.  Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors.  Installing some form of aftermarket window tinting that affects radio wave signals.  Lots of snow or ice around the wheels or wheel housings.  Using tire chains on the vehicle.  Using wheels/tires not equipped with TPMS sensors.  The radio unit is acting as the amplifier for audio output from the Auxiliary device.  Therefore, if the volume control on the Auxiliary device is set too low, there will be insufficient audio signal for the radio unit to play the", "device is set too low, there will be insufficient audio signal for the radio unit to play the music on the device.", "BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load", "cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will", "load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on GAWRs, vehicle loading, and trailer towing, see Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not", "rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.", "The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  Front View Camera When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted", "the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering", "image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are", "for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera", "on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the", "exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other", "Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle", "Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.", "then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "Preserving The Bodywork  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to", "are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.", "If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).", "When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Child-Protection Door Lock Location  Child-Protection Door Lock System \u2014 Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a", "a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove the sealing plug for access, and use a flat-blade screwdriver (or mechanical key) to rotate the dial to the lock or unlock position.  Note: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a", "and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Note: Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the", "is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).", "Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.  Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue", "is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.", "Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Note: Vehicle speeds shown in the preceding chart are for 2H and 4H only.  Vehicle speeds in 4L would be significantly less.  Manual transmission shift speeds in mph (km/h) engine speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.6l accel.  15 (24) 24 (39) 50 (80) 65 (104) 70 (112) cruise 10 (16) 19 (31) 40 (64) 55 (88) 65 (105) 8\u2013speed automatic transmission the transmission gear range (prndm) is displayed both beside the gear selector and in the instrument cluster.  To select a gear range, push the lock button on the gear selector and move the selector rearward or forward.  To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.  You", "the transmission out of PARK, the engine must be running and the brake pedal must be pressed.  You must also press the brake pedal to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is stopped or moving at low speeds.  Select the DRIVE range for normal driving.  The electronically controlled transmission adapts its shift schedule based on driver inputs, along with environmental and road conditions.  The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt.  This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers).  Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped.  Be sure to keep your foot on the brake pedal when shifting between these gears.  The transmission gear selector provides PARK, REVERSE, NEUTRAL, DRIVE and MANUAL (AutoStick) shift positions.  Manual shifts can be made using the AutoStick shift control.  Toggling the gear", "shift positions.  Manual shifts can be made using the AutoStick shift control.  Toggling the gear selector forward (-) or rearward (+) while in the MANUAL (AutoStick) position (beside the DRIVE position) will manually select the transmission gear, and will display the current gear in the instrument cluster Note: In the event of a mismatch between the gear selector position and the actual transmission gear (for example, driver selects PARK while driving), the position indicator will blink continuously until the selector is returned to the proper position, or the requested shift can be completed.  Note: If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  Recommended Vehicle Shift", "(into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Note: Vehicle speeds shown in the preceding chart are for 2H and 4H only.  Vehicle speeds in 4L would be significantly less.  With the vehicle rolling at 1 to 3 mph (2 to 5 km/h), shift an automatic transmission into NEUTRAL (N), or press the clutch pedal on a manual transmission.  While the vehicle is coasting at 1 to 3 mph (2 to 5 km/h), shift the transfer case lever firmly to the desired position.  Do not pause with the transfer case in N (Neutral).  Once the shift is completed, place the automatic transmission into DRIVE or release the clutch pedal on a manual transmission.  To utilize your manual", "into DRIVE or release the clutch pedal on a manual transmission.  To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Manual Transmission Shift Speeds in MPH (KM/H) Engine Speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.6L Accel.  15 (24) 24 (39) 50 (80) 65 (104) 70 (112) Cruise 10 (16) 19 (31) 40 (64) 55 (88) 65 (105) The transmission will automatically downshift as the vehicle slows (to prevent engine lugging) and will display the current gear.  The transmission will automatically downshift to FIRST gear when coming to a stop.  After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or THIRD gear, in 4L range).  Tapping (+) (at a stop) will allow starting in", "FIRST or SECOND gear (or THIRD gear, in 4L range).  Tapping (+) (at a stop) will allow starting in SECOND gear.  Starting out in SECOND or THIRD gear can be helpful in snowy or icy conditions.  If a requested downshift would cause the engine to overspeed, that shift will not occur.  The system will ignore attempts to upshift at too low of a vehicle speed.  Holding the gear selector in the (-) position will downshift the transmission to the lowest gear possible at the current speed.  Transmission shifting will be more noticeable when AutoStick is enabled.  The system may revert to automatic shift mode if a fault or overheat condition is detected.", "NEUTRAL (N) Use this range when the vehicle is standing for prolonged periods with the engine running.  Apply the parking brake and shift the transmission into PARK if you must exit the vehicle.  WARNING: Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.  These are unsafe practices that limit your response to changing traffic or road conditions.  You might lose control of the vehicle and have a collision.  CAUTION: Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle N (Neutral) Neutral \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicleWARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages", "without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  Five-position transfer case \u2014 if equipped the transfer case provides five positions: 2h (two-wheel drive high range) 4h auto (four-wheel drive auto high range) 4h part time (four-wheel drive part time high range) n (neutral) 4l (four-wheel drive low range) for additional information on the appropriate use of each transfer case position, see the following information:.  N (Neutral) Neutral \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicleWARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position", "or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.  See Recreational Towing for further information WARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic", "and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.", "SYNC Button Press the SYNC button on the touchscreen to toggle the Sync feature on/off.  The SYNC indicator illuminates when SYNC is on.  SYNC is used to synchronize the passenger temperature setting with the driver temperature setting.  Changing the passenger temperature setting while in SYNC will automatically exit this feature.  Note: The SYNC button is only available on the touchscreen.  Press the settings button on the touchscreen.  Press the paired phones or audio sources button.  Press to select the particular phone or the particular audio device.  A pop-up menu will appear; press \u201cConnect Phone\u201d.  Press the X to exit out of the Settings screen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing", "is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The MAX A/C button is only available on the touchscreen.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsThe SYNC button is only available on the touchscreen.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the", "for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Press the Phone button.  Press the Dial/Keypad button on the touchscreen.  The Touch-Tone screen will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press \u201cDial/Call\u201d.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM", "Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.", "Safety Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.  WARNING: Improperly inflated tires are dangerous and can cause collisions.  Underinflation increases tire flexing and can result in overheating and tire failure.  Overinflation reduces a tire's ability to cushion shock.  Objects on the road and chuckholes can cause damage that result in tire failure.  Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.  Unequal tire pressures can cause steering problems.  You could lose control of your vehicle.  Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.  Always drive with each tire inflated to the recommended cold tire inflation pressure.  Note: Unequal tire pressures from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure", "from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure from side to side may cause the vehicle to drift left or right.  FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.", "turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  Temperature Grades The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire", "wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.  Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.  For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire", "a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead", "the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was", "which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.", "Connected Services Vehicle Finder FAQs Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic,", "disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob", "to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media", "stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201dWARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an", "related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.", "Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately \"\u21e8air bag warning light\" .  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning", "as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bags to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Placing an object on", "you drive, have an authorized dealer service the air bag system immediately.  Placing an object on the floor under the front passenger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision.  Do not place any objects on the floor under the front passenger seat.  If there is a fault present in the OCS, both the PAD Indicator Light and the Air Bag Warning Light will illuminate to show that the Passenger Advanced Front Air Bag is deactivated.  Should this occur, the Passenger Advanced Front Air Bag will remain deactivated until the fault is cleared.  This indicates that you should take the vehicle to an authorized dealer for service immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light", "Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light will illuminate whenever the ocs is unable to classify the front passenger seat status.  A malfunction in the OCS may affect the operation of the air bag system.  If the air bag warning light does not come on, or stays on after you start the vehicle, or it comes on as you drive, take the vehicle to an authorized dealer for service immediately.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  Redundant Air Bag Warning Light If a fault with the Air Bag Warning Light is detected, which could", "Redundant Air Bag Warning Light If a fault with the Air Bag Warning Light is detected, which could affect the Supplemental Restraint System (SRS), the Redundant Air Bag Warning Light will illuminate on the instrument panel.  The Redundant Air Bag Warning Light will stay on until the fault is cleared.  In addition, a single chime will sound to alert you that the Redundant Air Bag Warning Light has come on and a fault has been detected.  If the Redundant Air Bag Warning Light comes on intermittently or remains on while driving have an authorized dealer service the vehicle immediately.  See \"\u21e8air bag warning light\" for more information regarding the redundant air bag warning light.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.", "The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C),", "allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full", "operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "There are four possible dipstick types: Always maintain the oil level within the crosshatch markings on the dipstick.  Adding 1 qt (1 L) of oil when the reading is at the low end of the dipstick range will raise the oil level to the high end of the range marking.  1 \u2014 Power Distribution Center (Fuses) 6 \u2014 Brake Fluid Reservoir Cap 2 \u2014 Battery 7 \u2014 Engine Air Cleaner Filter 3 \u2014 Engine Oil Dipstick 8 \u2014 Power Steering Fluid Reservoir Cap 4 \u2014 Engine Oil Fill 9 \u2014 Washer Fluid Reservoir Cap 5 \u2014 Engine Coolant Pressure Cap 1 \u2014 Battery 6 \u2014 Power Distribution Center (Fuses) 2 \u2014 Engine Oil Fill 7 \u2014 Power Steering Reservoir Cap 3 \u2014 Coolant Pressure Reservoir Cap 8 \u2014 Engine Oil Dipstick 4 \u2014 Brake Fluid Reservoir Cap 9 \u2014 Engine Air Cleaner Filter 5 \u2014 Washer Fluid Reservoir Cap Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and", "of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  To order a hard copy of your service or diagnostic procedure manuals, visit: www.techauthority.com (us and canada).", "Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety", "any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province,", "including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where", "Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html frequently asked questions about installing child restraints with seat belts what is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child", "anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward-facing child restraint, up to the recommended weight limit of the child restraint.  Can the rear-facing child restraint touch the back of the front passenger seat?  Yes contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.  Can the rear head restraints be removed?  Yes the center head restraint can be removed if it interferes with the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint?  No do not twist the buckle stalk in a seating position with an alr retractor.  Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the", "and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.  Use this simple 5-step test to decide whether the child can use the vehicle\u2019s seat belt alone: Can the child sit all the way back against the back of the vehicle seat?  Do the child\u2019s knees bend comfortably over the front of the vehicle seat while the child is still sitting all the way back?  Does the shoulder belt cross the child\u2019s shoulder between the neck and arm?  Is the lap part of the belt as low as possible, touching the child\u2019s thighs and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to any of these questions was \u201cno,\u201d then the child still needs to use a booster seat in this vehicle.  If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s squirming or slouching can move the belt out of position.  If the shoulder belt contacts the", "squirming or slouching can move the belt out of position.  If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.  WARNING: Never allow a child to put the shoulder belt under an arm or behind their back.  In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.  A child must always wear both the lap and shoulder portions of the seat belt correctly.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.", "is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned", "operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates", "temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine", "for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be", "when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool;", "upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  NORMAL OPERATION \u2014 DIESEL ENGINE Observe the following when the diesel engine is operating: All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater", "the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped)", "during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014", "1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service", "is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors", "a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software,", "into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  All cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Remove the two screws that pass through the bed sheet metal.  Tail Lamp Screws Pull the", "(136 kg).  Remove the two screws that pass through the bed sheet metal.  Tail Lamp Screws Pull the outboard side of the lamp rearward, far enough to unsnap the two receptacles on the outboard side of the lamp housing, from the two plastic snap post retainers in the outer box side panel.  Once removed, locate and rotate the appropriate socket a quarter turn counterclockwise, then remove it from the housing.  Pull the bulb straight from the socket to replace.  To install a new bulb, reverse the procedure above.  With the bag opened completely, fold the fabric divider downward and lay the rear window in the bottom of the bag.  Step One Fold the divider upward, covering the rear window.  Step Two Lay the first quarter panel cover assembly all the way to the right side and the second quarter panel cover assembly on the left side.  Secure both using the two hook-and-loop fastener straps on each side.  The quarter panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step Three 1 \u2014", "panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step Three 1 \u2014 Left Quarter Panel Cover Assembly 2 \u2014 Right Quarter Panel Cover Assembly Close the storage bag and store in a safe location.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the", "boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward", "side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  Press the settings button on the touchscreen.  Press the paired phones or audio sources button.  Press to select the particular phone or the particular audio device.  A pop-up menu will appear; press \u201cConnect Phone\u201d.  Press the X to exit out of the Settings screen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The MAX A/C button is only available on", "you to toggle up or down through the available settings.  The MAX A/C button is only available on the touchscreen.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsThe SYNC button is only available on the touchscreen.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of", "to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Press the Phone button.  Press the Dial/Keypad button on the touchscreen.  The Touch-Tone screen will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press \u201cDial/Call\u201d.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or", "press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the", "To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.", "will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.", "The engine is allowed to crank as long as 25 seconds.  If the engine fails to start during this period, please wait at least two minutes for the starter to cool before repeating start procedure.  If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filters to avoid engine damageInstall a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible", "pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damageThe system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  The transmission must be in PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage", "once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage automatically after 10 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Extended Park Starting Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Note: Extended Park condition occurs when the vehicle has not been started or driven for at least 30 days.  CAUTION: To prevent damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15", "damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeThis remote function requires your vehicle to be equipped with a factory-installed Remote Start system.", "On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the", "seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  Vacation/storage for information on maintaining the climate control system when the vehicle is being stored for an extended period of time, see \"\u21e8storing the vehicle\" .  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the", "the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Press and release this button to turn the Climate Control ON/OFF.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  To Turn Off The Engine Using The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control", "(A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control will turn off, but Stability Control will remain active.  Hold the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and", "Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.", "Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an", "information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system", "personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL", "your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.", "Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  When crossing a ravine, gully, ditch, washout or a large rut, the angled approach is the key to maintaining your vehicle's mobility.  Approach these obstacles at a 45-degree angle and let each tire go through the obstacle independently.  You need to use caution when crossing large obstacles with steep sides.  Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover.  If you get caught in a rut,", "at an angle great enough to put the vehicle at risk of a rollover.  If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires.  Use the removed dirt to fill the rut ahead of the turnout you just created.  You should now be able to drive out following the trench you just created at a 45-degree angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your", "a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with", "When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and", "of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.", "Identifying Whether You Have A Rolling Code Or Non-Rolling Code Device Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  You have 30 seconds in which to initiate rolling code final step 2, after completing rolling code final step 1.  Rolling Code Devices To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices", "if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Note: The \u201cLEARN\u201d or \u201cTRAIN\u201d button is not the button you normally use to operate the device.  Identifying Whether You Have A Rolling Code Or Non-Rolling Code Device Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  Non-rolling Code Devices Most devices manufactured before 1995 will not have a rolling code.  These devices will also not have a \u201cLEARN\u201d or \u201cTRAIN\u201d button.", "If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire", "will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to", "top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to", "so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx", "the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the", "form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited", "This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system", "of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use", "or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling,", "to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of", "of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.", "Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The", "for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated", "store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting", "approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedureWARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel", "in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Fuel System Cautions CAUTION: Follow these guidelines to maintain", "cause serious injury or death.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system", "the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic", "with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system", "is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the", "could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with", "For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press", "Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the", "km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that", "while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to", "Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.", "Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset", "section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main", "WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will", "Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac)", "the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe", "READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND", "function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.  Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and", "to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.", "STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can", "(ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both", "well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Lockout Service Whether the keys are locked in your vehicle or frozen locks are keeping you from getting on your way, help is just a phone call away.  This service is limited to providing access to the vehicle\u2019s seating area.  It does not cover the cost of replacement keys.  VEHICLE MAINTENANCE An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions", "Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  WARNING: You can be badly injured working on or around a motor vehicle.  Only do service work for which you have the knowledge and the proper equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a", "Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of", "are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK", "to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle", "handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.", "The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door opener Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  HomeLink\u00ae replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting, or home security systems.  The HomeLink\u00ae unit is powered by your vehicle\u2019s 12 Volt battery.  The HomeLink\u00ae buttons that are located in the overhead console or sunvisor designate the three different HomeLink\u00ae channels.  To operate HomeLink\u00ae, push and release any of the programmed HomeLink\u00ae buttons.  These buttons will activate the devices they are programmed to with each press of the corresponding HomeLink\u00ae button.  The HomeLink\u00ae indicator light is located above the center button.  Place the ignition in the ON/RUN position.  Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program", "hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program while keeping the HomeLink\u00ae indicator light in view.  Continue to press and hold the HomeLink\u00ae button, while you press and release (cycle) your hand-held transmitter every two seconds until HomeLink\u00ae has successfully accepted the frequency signal.  The indicator light will flash slowly and then rapidly when fully trained.  Watch for the HomeLink\u00ae indicator to change flash rates.  When it changes, it is programmed.  It may take up to 30 seconds or longer in rare cases.  The garage door may open and close while you are programming.  Press and hold the programmed HomeLink\u00ae button and observe the indicator light.  If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink\u00ae button is pressed.  To program the two remaining HomeLink\u00ae buttons, repeat each step for each remaining button.  DO NOT erase the channels.  Programming HomeLink\u00ae To A Garage", "each step for each remaining button.  DO NOT erase the channels.  Programming HomeLink\u00ae To A Garage Door Opener To program any of the HomeLink\u00ae buttons to activate your garage door opener motor, proceed as follows: Place the ignition switch into the ON/RUN position.  Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program, while keeping the HomeLink\u00ae indicator light in view.  Push and hold the HomeLink\u00ae button you want to program while you push and hold the garage door opener transmitter button you are trying to replicate.  Continue to hold both buttons and observe the HomeLink\u00ae indicator light.  The HomeLink\u00ae indicator light will flash slowly and then rapidly.  Once this happens, release both buttons.  Note: All HomeLink\u00ae buttons are programmed using this procedure.  You do not need to erase all channels when programming additional buttons.  Note: Make sure the garage door opener motor is plugged in before moving on to the rolling", "Note: Make sure the garage door opener motor is plugged in before moving on to the rolling code/non-rolling code final steps.  Programming HomeLink\u00ae To A Miscellaneous Device The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door openerBe sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  Note: Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission, which may not be long enough for HomeLink\u00ae to pick up the signal during programming.  Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner.  The procedure may need to be performed multiple times to successfully pair the device to your HomeLink\u00ae buttons.  Before You Begin Programming HomeLink\u00ae For efficient programming and accurate transmission of the radio-frequency signal, it is recommended that a new battery be placed", "accurate transmission of the radio-frequency signal, it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink\u00ae system.  Make sure your hand-held transmitter is programmed to activate the device you are trying to program your HomeLink\u00ae button to.  Ensure that your vehicle is parked outside of the garage before you begin programming.  It is recommended that you erase all the channels of your HomeLink\u00ae before you use it for the first time.  Programming HomeLink\u00ae To A Garage Door Opener To program any of the HomeLink\u00ae buttons to activate your garage door opener motor, proceed as follows: Place the ignition switch into the ON/RUN position.  Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program, while keeping the HomeLink\u00ae indicator light in view.  Push and hold the HomeLink\u00ae button you want to program while you push and hold the garage door opener transmitter button you are", "you want to program while you push and hold the garage door opener transmitter button you are trying to replicate.  Continue to hold both buttons and observe the HomeLink\u00ae indicator light.  The HomeLink\u00ae indicator light will flash slowly and then rapidly.  Once this happens, release both buttons.  Note: All HomeLink\u00ae buttons are programmed using this procedure.  You do not need to erase all channels when programming additional buttons.  Note: Make sure the garage door opener motor is plugged in before moving on to the rolling code/non-rolling code final steps.", "The ignition switch must be in the ACC or ON/RUN position to adjust the power mirrors.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the", "unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP", "is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  START The engine will start.  Note: In case the ignition switch does not change with the push of the START/STOP ignition button, the key fob may have a low or depleted battery.  In this situation, a backup method can be used to operate the ignition switch.  Put the nose side of the key fob (side with the mechanical flip key) against the START/STOP ignition button and push to operate the ignition switch.  CAUTION: Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to", "the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.  WARNING: When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the Keyless Enter \u2018n Go\u2122 Ignition in the ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat buildup may cause serious injury or death.", "inside parked vehicles in hot weather.  Interior heat buildup may cause serious injury or death.  CAUTION: An unlocked vehicle is an invitation for thieves.  Always remove key fob from the vehicle and lock all doors when leaving the vehicle unattended.  Note: When opening the driver's door with the ignition in the ON/RUN (engine not running) position, a chime will sound to remind you to place the ignition in the OFF position.  In addition to the chime, the message will display \u201cIgnition Or Accessory On\u201d in the cluster.  ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push", "once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:", "Removing the soft top removing the soft top \u00b9 use this qr code to access your digital experience.  Fully lower the soft top to the Sunrider\u00ae positionCaution: failure to follow the next steps could result in damage to the soft top or vehicle.  Using the provided #T50 Torx head driver and ratchet, unscrew the two Torx head fasteners on the inside of each top mechanism.  Step two utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle\u2019s sport bar and trim.  Store the soft top in a safe, clean, and dry location.  Remove the door frames.  The rear door frames must be removed before the front door framesUsing the provided #T50 Torx head driver and ratchet, unscrew the six Torx head fasteners on both rear corners and the back of the cab, then remove the belt rail.  Note: folding down the rear seats is recommended to provide easier access to the fasteners.  Step five 1 \u2014 corner fasteners 2 \u2014 rear fasteners.  Lowering the soft top \u00b9 use this qr code to access your digital", "fasteners 2 \u2014 rear fasteners.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Fully lower the soft top to the Sunrider\u00ae positionFailure to follow the next steps could result in damage to the soft top or vehicle.  Using the provided #T50 Torx head driver and ratchet, unscrew the two Torx head fasteners on the inside of each top mechanism.  Step Two Utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle\u2019s sport bar and trim.  Store the soft top in a safe, clean, and dry location.  Remove the door frames.  The rear door frames must be removed before the front door framesUsing the provided #T50 Torx head driver and", "frames must be removed before the front door framesUsing the provided #T50 Torx head driver and ratchet, unscrew the six Torx head fasteners on both rear corners and the back of the cab, then remove the belt rail.  Folding down the rear seats is recommended to provide easier access to the fasteners.  Step Five 1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage", "top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.", "Electronic Sway Bar Disconnect \u2014 If Equipped Your vehicle may be equipped with an electronic disconnecting stabilizer/sway bar.  This system allows greater front suspension travel in off-road situations.  This system is controlled by the SWAY BAR switch located on the instrument panel (to the right of the steering column).  Push the SWAY BAR switch to disconnect or connect the sway bar.  The Sway Bar Indicator Light (located in the instrument cluster) will illuminate when the bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when activation conditions are not met.  The stabilizer/sway bar should remain in on-road mode during normal driving conditions.  To disconnect the stabilizer/sway bar, shift to either 4H or 4L and push the SWAY BAR switch to obtain the off-road position The Sway Bar Indicator Light will flash until the stabilizer/sway bar has been fully disconnected.  To return to on-road mode, push the SWAY BAR switch again.  WARNING: Ensure the", "disconnected.  To return to on-road mode, push the SWAY BAR switch again.  WARNING: Ensure the stabilizer/sway bar is reconnected before driving on hard surfaced roads or at speeds above 18 mph (29 km/h); a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  Under certain circumstances, the front stabilizer/sway bar enhances vehicle stability and assists with vehicle control.  The system monitors vehicle speed and will attempt to reconnect the stabilizer/sway bar at speeds over 18 mph (29 km/h).  This is indicated by a flashing or solid Sway Bar Indicator Light.  Once vehicle speed is reduced below 14 mph (22 km/h), the system will once again attempt to return to off-road mode.  Note: The stabilizer/sway bar may be torque locked due to left and right suspension height differences.  This condition is due to driving surface differences or vehicle loading.  In order for the stabilizer/sway bar to disconnect/reconnect, the right and left halves", "loading.  In order for the stabilizer/sway bar to disconnect/reconnect, the right and left halves of the bar must be aligned.  This alignment may require that the vehicle be driven onto level ground or rocked from side to side.  WARNING: If the stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not attempt to drive the vehicle over 18 mph (29 km/h).  Driving faster than 18 mph (29 km/h) with a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  Sway Bar Fault Warning Light \u2014 If Equipped This light will illuminate when there is a fault in the sway bar disconnect system Sway Bar Indicator Light \u2014 If Equipped This indicator light will illuminate when the front sway bar is disconnected.  Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt", "to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.  When TSC is functioning, the ESC Activation/Malfunction Indicator Light will flash, the engine power may be reduced, and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying.  TSC is disabled when the ESC system is in the \u201cPartial Off\u201d or \u201cFull Off\u201d modes.  Note: TSC cannot stop all trailers from swaying.  Always use caution when towing a trailer and follow the trailer tongue weight recommendations.  See \"\u21e8trailer towing\" for further information.  WARNING: If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway.  Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted", "provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.", "Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.  Opening To open the tailgate,", "close the tailgate, lift upward until both sides latch into place.  Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014", "the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the", "it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.", "The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are", "turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings", "seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The engine must be running for the heated steering wheel to operate.  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or", "is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.", "Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an", "information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system", "personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL", "your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.", "In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L 4H The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only", "at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  4H This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front", "surfaced roads.  4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front wheels.  The four-wheel drive system will be automatically engaged when the vehicle senses a loss of traction.  This range provides additional traction for varying road conditions.", "Under seat storage \u2014 if equipped your vehicle may be equipped with two options for under seat storage: non-locking storage wall under seat locking storage bin locking storage bin if equipped, the locking storage bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor", "Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out", "seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Rear Seat Stadium Position The rear seat bottoms can be folded upward into the Stadium Position to create more storage space on the vehicle\u2019s floor, and to access the under seat storage bins (if equipped).  To fold the seat bottom upward, proceed as follows: Lift upward on each section of the seat bottom.  Lift from beneath seat (left side shown) raise the seat bottom upward into the stadium position.  Stadium Position To return the seat bottom to the normal position, push downward on the raised seat bottom.", "Shifting Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Transmission function is monitored electronically for abnormal conditions.  If a condition is detected that could result in transmission damage, Transmission Limp Home mode is activated.  In this mode, the transmission may operate only in certain gears, or may not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some situations, the transmission may not re-engage if the engine is", "and the engine may stall.  In some situations, the transmission may not re-engage if the engine is turned off and restarted.  The Malfunction Indicator Light (MIL) may be illuminated.  A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary.  It is important to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only manufacturer's specified transmission fluid It is important to maintain the transmission fluid at the correct level using the recommended fluid.  Using a transmission fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is", "the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  Using a lower gear while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  This action will also provide better engine braking.  Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing a heavy trailer), use the AutoStick shift control to select a lower gear Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting", "a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  During cold weather, you may experience increased effort in shifting until the transmission fluid warms up.  This is normal.  Routine fluid and", "effort in shifting until the transmission fluid warms up.  This is normal.  Routine fluid and filter changes are not required.  However, change the fluid and filter if the fluid becomes contaminated (with water, etc.  ), or if the transmission is disassembled for any reason.  FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  Do Not Operate The Engine With Failed Parts All engine failures give some warning before the parts fail.  Be on the alert for changes in", "Parts All engine failures give some warning before the parts fail.  Be on the alert for changes in performance, sounds, and visual evidence that the engine requires service.  Some important clues are: engine misfiring or vibrating severely sudden loss of power unusual engine noises fuel, oil or coolant leaks sudden change, outside the normal operating range, in the engine operating temperature excessive smoke oil pressure drop shifting fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or", "is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.", "Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Important Safety Precautions Please", "the seat belt, which could result in serious injury or death.  Important Safety Precautions Please pay close attention to the information in this section.  It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.  Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: Children 12 years old and under should always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint Never allow children to slide the shoulder belt behind them or under their arm.  You should read the instructions provided with your child restraint to make sure that you are using it", "should read the instructions provided with your child restraint to make sure that you are using it properly.  All occupants should always wear their lap and shoulder belts properly.  The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate.  Do not lean against the door or window.  If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.  If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see \"\u21e8if you need assistance\" for customer service contact information.  WARNING: Never place a rear-facing child restraint in front of an air bag.  A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.  Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing", "Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing child restraint in the rear seat.  If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle.  Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will", "the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Folding The Rear Seats To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently To raise the seatback to the proper position, manually lift the seatback until it locks into place.  To return the head restraint to the proper position, manually lift up until it locks into place.  If interference from the cargo area behind the seat prevents the seatback from fully locking, you will have difficulty returning the seats to their proper position.  Note: Each rear seatback can be locked in an upright position using the vehicle key.  Each seatback must be unlocked to release for", "locked in an upright position using the vehicle key.  Each seatback must be unlocked to release for folding.  Note: The vehicle is equipped with stow clips located on the lower trim, next to the rear seats.  Use these clips to hold the seat belt out of the path of the seatback when it is being folded and raised.  Stow clip location you may experience deformation in the seat cushion from the seat belt buckles if the seats are left folded for an extended period of time.  This is normal.  By simply unfolding the seats to the open position, the seat cushion will return to its normal shape over time.  WARNING: Be certain that the seatback is securely locked into position.  Perform a \u201cpush - pull - push\u201d check to confirm the seat is fully locked.  If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers.  A red indicator on the pull strap will be displayed if the seatback is not securely locked.  An improperly latched seat could cause", "will be displayed if the seatback is not securely locked.  An improperly latched seat could cause serious injury.  Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, adjacent to the anchorage symbols on the seatback.  They are just visible when you lean into the rear seat to install the child restraint.  You will easily feel them if you run your finger along the gap between the seatback and seat cushion.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn", "alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals:", "the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.", "Off-Road Driving Tips  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock", "every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be", "use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also", "under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while", "for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches", "toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed", "in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer", "plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can", "damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage", "continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could", "ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  Pitch & Roll The Pitch & Roll page displays the vehicle\u2019s current pitch (angle up and down) and roll (angle side to side) in degrees.  The Pitch & Roll gauges provide a visualization of the current vehicle angle.  How It Works Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your", "and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.  Vehicle info push and release the up or down arrow button until the vehicle info menu icon is displayed in the instrument cluster display.  Push and release the left or right arrow button to scroll through the information submenus and push and release the ok button to select or reset the resettable submenus.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized", "appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about", "www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone", "In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security", "is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Manual Seat Height Adjustment The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.  Lumbar Support The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  Manual Seat Height Adjustment The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.  Adjustable Upper Shoulder Belt Anchorage In the driver and outboard front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt", "seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck.  Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.  As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position.  After you release the anchorage button, try to move it up or down to make sure that it is locked in position.  Note: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature.  This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release button.  To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position.  WARNING: Wearing your seat belt incorrectly could make your injuries in a collision much worse.  You", "Wearing your seat belt incorrectly could make your injuries in a collision much worse.  You might suffer internal injuries, or you could even slide out of the seat belt.  Follow these instructions to wear your seat belt safely and to keep your passengers safe, too.  Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and not resting on your neck.  The retractor will withdraw any slack in the shoulder belt.  Misadjustment of the seat belt could reduce the effectiveness of the safety belt in a crash.  Always make all seat belt height adjustments when the vehicle is stationary.  The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  In the driver and outboard front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck.  Push or squeeze the", "be adjusted upward or downward to position the seat belt away from your neck.  Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.", "STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can", "(ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both", "well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Lockout Service Whether the keys are locked in your vehicle or frozen locks are keeping you from getting on your way, help is just a phone call away.  This service is limited to providing access to the vehicle\u2019s seating area.  It does not cover the cost of replacement keys.  VEHICLE MAINTENANCE An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions", "Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  WARNING: You can be badly injured working on or around a motor vehicle.  Only do service work for which you have the knowledge and the proper equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will", "system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result", "to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Vacation/storage for information on maintaining the climate control system when the vehicle is being stored for an extended period of time, see \"\u21e8storing the vehicle\" .", "Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio.  This condition may be lessened or eliminated by repositioning the mobile phone within the vehicle.  This condition is not harmful to the radio.  If your radio performance does not satisfactorily improve from repositioning the mobile phone, it is recommended that the volume be turned down or off during mobile phone operation when not using the Uconnect system.  Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors.  Installing some form of aftermarket window tinting that affects radio wave signals.  Lots of snow or ice around the wheels or wheel housings.  Using tire chains on the vehicle.  Using wheels/tires not equipped with TPMS sensors.  The radio unit is acting as the amplifier for audio output from the Auxiliary device.  Therefore, if the volume control on the Auxiliary device is set too low, there will be", "device.  Therefore, if the volume control on the Auxiliary device is set too low, there will be insufficient audio signal for the radio unit to play the music on the device.  Sos call system limitations vehicles sold in mexico do not have sos call system capabilities.  SOS or other emergency line operators in Mexico may not answer or respond to SOS system calls.  If the SOS Call system detects a malfunction, any of the following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d an in-vehicle audio message will state \u201cvehicle device requires service.  Please contact an authorized dealer.\u201d even if the sos call system is fully functional, factors beyond fca us llc\u2019s control may prevent or stop the sos call system operation.  These include, but are not", "fca us llc\u2019s control may prevent or stop the sos call system operation.  These include, but are not limited to, the following factors: the ignition is in the off position the vehicle\u2019s electrical systems are not intact the sos call system software and/or hardware are damaged during a crash the vehicle battery loses power or becomes disconnected during a vehicle crash lte (voice/data) or 4g (data) network and/or global positioning satellite signals are unavailable or obstructed equipment malfunction at the sos operator facility operator error by the sos operator lte (voice/data) or 4g (data) network congestion weather buildings, structures, geographic terrain, or tunnels warning: ignoring the rearview mirror light could mean you will not have sos call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the", "turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber.  Never place anything on or near the vehicle\u2019s LTE (voice/data) or 4G (data) and GPS antennas.  You could prevent LTE (voice/data) or 4G (data) and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable LTE (voice/data) or 4G (data) network connection and a GPS", "placing an emergency call.  An operable LTE (voice/data) or 4G (data) network connection and a GPS signal is required for the SOS Call system to function properly.  Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time", "Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Apple CarPlay\u00ae.  Anywhere using your mobile device and Vehicle Branded App From your computer on the Owner\u2019s Site (not available on all functions) Contacting SiriusXM Guardian\u2122 Customer Care (not available on all functions) Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.", "The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door opener Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  HomeLink\u00ae replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting, or home security systems.  The HomeLink\u00ae unit is powered by your vehicle\u2019s 12 Volt battery.  The HomeLink\u00ae buttons that are located in the overhead console or sunvisor designate the three different HomeLink\u00ae channels.  To operate HomeLink\u00ae, push and release any of the programmed HomeLink\u00ae buttons.  These buttons will activate the devices they are programmed to with each press of the corresponding HomeLink\u00ae button.  The HomeLink\u00ae indicator light is located above the center button.  Place the ignition in the ON/RUN position.  Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program", "hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program while keeping the HomeLink\u00ae indicator light in view.  Continue to press and hold the HomeLink\u00ae button, while you press and release (cycle) your hand-held transmitter every two seconds until HomeLink\u00ae has successfully accepted the frequency signal.  The indicator light will flash slowly and then rapidly when fully trained.  Watch for the HomeLink\u00ae indicator to change flash rates.  When it changes, it is programmed.  It may take up to 30 seconds or longer in rare cases.  The garage door may open and close while you are programming.  Press and hold the programmed HomeLink\u00ae button and observe the indicator light.  If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink\u00ae button is pressed.  To program the two remaining HomeLink\u00ae buttons, repeat each step for each remaining button.  DO NOT erase the channels.  Programming HomeLink\u00ae To A Garage", "each step for each remaining button.  DO NOT erase the channels.  Programming HomeLink\u00ae To A Garage Door Opener To program any of the HomeLink\u00ae buttons to activate your garage door opener motor, proceed as follows: Place the ignition switch into the ON/RUN position.  Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program, while keeping the HomeLink\u00ae indicator light in view.  Push and hold the HomeLink\u00ae button you want to program while you push and hold the garage door opener transmitter button you are trying to replicate.  Continue to hold both buttons and observe the HomeLink\u00ae indicator light.  The HomeLink\u00ae indicator light will flash slowly and then rapidly.  Once this happens, release both buttons.  Note: All HomeLink\u00ae buttons are programmed using this procedure.  You do not need to erase all channels when programming additional buttons.  Note: Make sure the garage door opener motor is plugged in before moving on to the rolling", "Note: Make sure the garage door opener motor is plugged in before moving on to the rolling code/non-rolling code final steps.  Programming HomeLink\u00ae To A Miscellaneous Device The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door opener Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  Note: Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission, which may not be long enough for HomeLink\u00ae to pick up the signal during programming.  Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner.  The procedure may need to be performed multiple times to successfully pair the device to your HomeLink\u00ae buttons.  Identifying Whether You Have A Rolling Code Or Non-Rolling Code Device Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the", "Device Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  Before You Begin Programming HomeLink\u00ae For efficient programming and accurate transmission of the radio-frequency signal, it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink\u00ae system.  Make sure your hand-held transmitter is programmed to activate the device you are trying to program your HomeLink\u00ae button to.  Ensure that your vehicle is parked outside of the garage before you begin programming.  It is recommended that you erase all the channels of your HomeLink\u00ae before you use it for the first time.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too", "gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat,", "the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce", "off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on,", "while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system", "vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.", "Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  The MIL will flash for about 10 seconds and then return to being fully", "service is required.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will", "come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running,", "before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can", "position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because", "vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must", "the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the", "i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.  Methylcyclopentadienyl Manganese Tricarbonyl (MMT) In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasolines to", "In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasolines to increase octane.  Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT.  Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles.  The manufacturer recommends that gasoline without MMT be used in your vehicle.  The MMT content of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gasoline retailer whether the gasoline contains MMT.  MMT is prohibited in Federal law and California reformulated gasoline.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or", "void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause", "may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are", "gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.", "Carbon Monoxide Warnings WARNING: Carbon monoxide (CO) in exhaust gases is deadly.  Follow the precautions below to prevent carbon monoxide poisoning: Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when", "is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Exhaust gases can injure or kill.  They contain carbon monoxide (CO), which is colorless and odorless.  Breathing it can make you unconscious and can eventually poison you.  To avoid breathing (CO), follow these safety tips: Carbon monoxide (CO) in exhaust gases is deadly.  Follow the precautions below to prevent carbon monoxide poisoning: Exhaust gases can injure or kill.  They contain carbon monoxide (CO), which is colorless and odorless.  Breathing it can make you unconscious and can eventually poison you.  To avoid breathing CO see A hot exhaust system can start a fire if you park over materials that can burn, such as grass or leaves, and those items that come into contact with your exhaust system.  Do not park or operate your vehicle in areas where", "come into contact with your exhaust system.  Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.  For further information For further information For further information The VIN is found on the left front corner of the A-pillar, visible from outside of the vehicle through the windshield.  Android\u2122 is a trademark of Google Inc. es posible que este equipo o dispositivo no cause interferencia perjudicial y este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operaci\u00f3n no deseada.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is", "never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.", "Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can", "Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  push the VR button, After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s", "system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  push the VR button, After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform", "commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.", "Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the", "form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background", "for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of", "\u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Setting name description voice response length this setting will change the response length for the voice recognition system.  The \u201cBrief\u201d setting provides a shortened audio description from the system.  The \u201cDetailed\u201d setting provides the full audio description from the system.  Show command list this setting will allow you to turn the command list on or off.  The \u201cAlways\u201d setting will always show the Command List.  The \u201cWith Help\u201d setting will show the Command List and provide a brief description of what the command does.  The \u201cNever\u201d setting will turn the Command List off.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune", "the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.", "Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.", "will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To", "and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.", "There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Prior to off-road usage, the side steps should be removed to prevent damage.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in", "Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Side Step", "assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Side Step Removal \u2014 If Equipped There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener locations (one side) remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side steps should be removed to prevent damage.  Side Step Removal \u2014 If Equipped There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four", "the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener locations (one side) remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side steps should be removed to prevent damage.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been", "or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.", "Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button,", "volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold", "which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Natural Speech Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Natural speech allows the user to speak commands in phrases or complete sentences.  The system filters out certain non-word utterances and sounds such as", "or complete sentences.  The system filters out certain non-word utterances and sounds such as \u201cah\u201d and \u201ceh.\u201d The system handles fill-in words such as \u201cI would like to\u201d.  The system handles multiple inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you want to call?\u201d in the case where a phone call was requested but the specific name was not recognized.  The system utilizes continuous dialog.  When the system requires more information from the user, it will ask a question to which the user can respond without pushing the Voice Command button on the steering wheel.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c", "cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  push the VR button, After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear", "the VR button, After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.", "Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.", "in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly", "accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If You Stall Or Begin To Lose Headway If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: If the engine stalls or you lose headway or cannot make it to the top of a steep", "to lock.  WARNING: If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  If the engine stalls or you lose", "with caution, maintaining your momentum as you climb the hill.  If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail", "if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.", "Adding Diesel Exhaust Fluid The DEF gauge (located on the instrument cluster display) will display the level of DEF remaining in the tankNote: Driving conditions (altitude, vehicle speed, load, etc.)  will affect the amount of DEF that is used in your vehicle.  System Overview This vehicle is equipped with a Diesel Exhaust Fluid (DEF) injection system and a Selective Catalytic Reduction (SCR) catalyst to meet the emission requirements.  The def injection system consists of the following components: def tank def pump def injector electronically-heated def lines nox sensors temperature sensors scr catalyst the def injection system and scr catalyst enable the achievement of diesel emissions requirements; while maintaining outstanding fuel economy, drivability, torque and power ratings.  For system messages and warnings see Note: Your vehicle is equipped with a DEF injection system.  You may occasionally hear an audible clicking noise from under the vehicle at a stop.  This is normal operation.  The DEF pump", "audible clicking noise from under the vehicle at a stop.  This is normal operation.  The DEF pump will run for a period of time after engine shutdown to purge the DEF system.  This is normal operation and may be audible from the rear of the vehicle.  DEF Fill Procedure Remove cap from DEF fill inlet (located in fuel door).  Fuel and diesel exhaust fluid fill location 1 \u2014 diesel fuel filler 2 \u2014 diesel exhaust fluid filler insert def fill adapter/nozzle into def fill inlet.  Note: the def gauge may take up to five seconds to update after adding a gallon or more of diesel exhaust fluid (def) to the def tank.  If you have a fault related to the DEF system, the gauge may not update to the new level.  See an authorized dealer for service.  The DEF gauge may also not immediately update after a refill if the temperature of the DEF fluid is below 12\u00b0F (-11\u00b0C).  The DEF line heater will possibly warm up the DEF fluid and allow the gauge to update after a period of run time.  Under very cold conditions, it is possible", "allow the gauge to update after a period of run time.  Under very cold conditions, it is possible that the gauge may not reflect the new fill level for several drives.  Excessive overfilling of the DEF tank can result in a MIL lamp/fault code and inaccurate level readings.  Refilling with nozzles you can fill up at any def distributor.  Proceed as follows: insert the def nozzle in the filler, start refilling and stop refilling at the first shut-off (the shut-off indicates that the def tank is full).  Do not proceed with the refilling, to prevent spillage of DEF.  Extract the nozzle.  Refilling with containers proceed as follows: check the expiration date.  Read the advice for use on the label before pouring the content of the bottle into the DEF tank.  If systems which cannot be screwed in (e.g.  Tanks) are used for refilling, after the indication appears on the instrument panel display \"\u21e8instrument cluster display\" fill the def tank with no more than 2 gal (8 l).  If containers which can be screwed to the", "fill the def tank with no more than 2 gal (8 l).  If containers which can be screwed to the filler are used, the reservoir is full when the DEF level in the container stops pouring out.  Do not proceed further.  Caution: to avoid def spillage, and possible damage to the def tank from overfilling, do not \u201ctop off\u201d the def tank after filling.  DO NOT OVERFILL.  DEF will freeze below 12\u00baF (-11\u00baC).  The DEF system is designed to work in temperatures below the DEF freezing point, however, if the tank is overfilled and freezes, the system could be damaged.  When DEF is spilled, clean the area immediately with water and use an absorbent material to soak up the spills on the ground.  Do not attempt to start your engine if DEF is accidentally added to the diesel fuel tank as it can result in severe damage to your engine, including but not limited to failure of the fuel pump and injectors.  Never add anything other than DEF to the tank \u2013 especially any form of hydrocarbon such as diesel fuel, fuel system additives,", "DEF to the tank \u2013 especially any form of hydrocarbon such as diesel fuel, fuel system additives, gasoline, or any other petroleum-based product.  Even a very small amount of these, less than 100 parts per million or less than 1 oz.  per 78 gal (295 L) will contaminate the entire DEF system and will require replacement.  If owners use a container, funnel or nozzle when refilling the tank, it should either be new or one that has only been used for adding DEF.  Mopar\u00ae provides an attachable nozzle with its DEF for this purpose.  Stop filling the DEF tank immediately when any of the following happen: DEF stops flowing from the fill bottle into the DEF fill inlet, DEF splashes out the fill inlet, or a DEF pump nozzle automatically shuts off.  Reinstall cap onto DEF fill inlet.  Note: For the correct DEF fluid type see Adding Diesel Exhaust Fluid The DEF gauge (located on the instrument cluster display) will display the level of DEF remaining in the tank Note: Driving conditions (altitude, vehicle speed, load,", "the level of DEF remaining in the tank Note: Driving conditions (altitude, vehicle speed, load, etc.)  will affect the amount of DEF that is used in your vehicle.  Diesel Exhaust Fluid Diesel Exhaust Fluid (DEF) sometimes known simply by the name of its active component, UREA, is a key component of Selective Catalytic Reduction (SCR) systems, which help diesel vehicles meet stringent emission regulations.  DEF is a liquid reducing agent that reacts with engine exhaust in the presence of a catalyst to convert smog-forming Nitrogen Oxides (NOx) into harmless nitrogen and water vapor.  For further information", "REFUELING IN EMERGENCY \u2013 IF EQUIPPED The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Note: In certain cold conditions, ice may prevent the fuel door from opening.  If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button.  Do not pry on the door.  See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you", "flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine", "will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24", "by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  If Engine Fails To Start If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  WARNING: Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.", "flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly CAUTION: To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  Normal Starting Observe the instrument cluster lights when starting the engine.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  Note: a delay of the start of up to", "brake pedal while pushing the ENGINE START/STOP button once.  Note: a delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  Caution: if the water in fuel indicator light remains on, do not start the engine before you drain the water from the fuel filters to avoid engine damage.  The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Note: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF", "pumping or pressing the accelerator pedal.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load", "OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Stopping The Engine After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Note: Refer to the following chart for proper engine shutdown.  Note: Under certain conditions the Stop/Start system may be temporarily disabled and the engine fan will run after the engine is turned off to protect the engine.  These conditions are under high load and high temperature conditions.", "On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the", "seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not", "shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Press and release this button to turn the Climate Control ON/OFF.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  To Turn Off The Engine Using The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control will turn off, but Stability Control will remain active.  Hold the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC", "the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to", "turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  A/C Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Note: For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.", "Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle", "X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the", "the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is", "will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF", "touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.", "Setting Name Description Language This setting will change the language of the Uconnect system and Instrument Cluster Display.  The available languages are \u201cEnglish\u201d, \u201cFran\u00e7ais\u201d, and \u201cEspa\u00f1ol\u201d.  Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Press the Media button on the touchscreen to begin.  Change the source to \u201cBluetooth\u00ae\u201d.  Press the Bluetooth\u00ae button on the touchscreen to display the Paired Audio Devices screen.  Press the Add Device button on the touchscreen.  If there is no device currently connected with the system, a pop-up will appear.  Search for available devices on your Bluetooth\u00ae-enabled audio device.  When prompted on the device, confirm the PIN shown on the Uconnect screen.  Uconnect Phone will display an in-process screen while the system is connecting.  When the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite device.  Selecting \u201cYes\u201d will make this device the highest priority.", "or not this is your favorite device.  Selecting \u201cYes\u201d will make this device the highest priority.  This device will take precedence over other paired devices within range.  Uconnect Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  Setting name description language this setting will change the language of the uconnect system and instrument cluster display.  The available languages are \u201cEnglish\u201d, \u201cFran\u00e7ais\u201d, and \u201cEspa\u00f1ol\u201d.  Natural Speech Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Natural speech allows the user to speak commands in phrases or complete sentences.  The system filters out certain non-word utterances and sounds such as \u201cah\u201d and \u201ceh.\u201d The system handles fill-in words such as \u201cI would like to\u201d.  The system handles multiple inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For", "inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you want to call?\u201d in the case where a phone call was requested but the specific name was not recognized.  The system utilizes continuous dialog.  When the system requires more information from the user, it will ask a question to which the user can respond without pushing the Voice Command button on the steering wheel.  When the Language button is pressed on the touchscreen, the system displays the different language options.  Once an option is selected, the system will display in the chosen language.  The available setting is: note: depending on the vehicle\u2019s options, feature settings may vary.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu", "press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.", "Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect", "against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.", "vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code", "leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants", "are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the", "the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric topDo not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  If the temperature is below", "installation can cause water to leak into the vehicle's interior.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on", "of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle", "the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "Adaptive Cruise Control (ACC) Ready Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.  Monitoring battery level status led light red 40% or lower yellow 40% to 70% green 70% to 100% electronic stability control (esc) active warning light \u2014 if equipped this warning light will indicate when the electronic stability control system is active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and", "30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.  Adaptive Cruise Control (ACC) Set Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.  Adaptive Cruise Control (ACC) Ready Indicator Light", "control has been turned on, but not set.  Adaptive Cruise Control (ACC) Ready Indicator Light \u2014 If Equipped With a Premium Instrument Cluster This light will turn on when the vehicle equipped with Adaptive Cruise Control (ACC) has been turned on, but not set.", "Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be", "these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the", "upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside),", "Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.", "or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels", "top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the", "first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five", "up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.", "Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C.These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  For the recommended", "acceleration, cornering, hydroplaning, or peak traction characteristics.  For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet", "highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests,", "wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.", "Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle.  These kinds of hitches are commonly used to tow small and medium sized trailers.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle", "Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the", "used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  When using a fascia/bumper mounted ball on any model, the trailer weight is limited to 3,500 lb (1,588 kg), 30 ft 2 (2.79 m 2 ) frontal area, and 350 lb (159 kg) tongue weight.  The trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie.  the GVWR), and the", "must be considered as part of the combined weight of occupants and cargo (ie.  the GVWR), and the GVWR should never exceed the weight referenced on the Tire And Loading Information Placard", "The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring Height (H) Attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the", "approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  Service Forward Collision Warning (FCW) Light \u2014 If Equipped This warning light will illuminate to indicate a fault in the Forward Collision Warning System.", "This warning light will illuminate to indicate a fault in the Forward Collision Warning System.  Contact an authorized dealer for service Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.", "System Overview This vehicle is equipped with a Diesel Exhaust Fluid (DEF) injection system and a Selective Catalytic Reduction (SCR) catalyst to meet the emission requirements.  The def injection system consists of the following components: def tank def pump def injector electronically-heated def lines nox sensors temperature sensors scr catalyst the def injection system and scr catalyst enable the achievement of diesel emissions requirements; while maintaining outstanding fuel economy, drivability, torque and power ratings.  For system messages and warnings see Note: Your vehicle is equipped with a DEF injection system.  You may occasionally hear an audible clicking noise from under the vehicle at a stop.  This is normal operation.  The DEF pump will run for a period of time after engine shutdown to purge the DEF system.  This is normal operation and may be audible from the rear of the vehicle.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control", "localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  Trailer Sway Control (TSC) TSC", "standards required by the Environmental Protection Agency.  Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.  When TSC is functioning, the ESC Activation/Malfunction Indicator Light will flash, the engine power may be reduced, and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying.  TSC is disabled when the ESC system is in the \u201cPartial Off\u201d or \u201cFull Off\u201d modes.  Note: TSC cannot stop all trailers from swaying.  Always use caution when towing a trailer and follow the trailer tongue weight recommendations.  See \"\u21e8trailer towing\" for further information.  WARNING: If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway.", "Connected Services Roadside Assistance FAQs What is the phone number for roadside assistance call?  The phone number is: us: 1-800-521-2779 canada: 1-800-363-4869 if i am subscribed to siriusxm guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance.  No, however your new vehicle may include Roadside Assistance Call services.  What to Do If your vehicle requires jump start assistance, out of gas/fuel delivery, tire service, lockout service or towing as a result of a mechanical breakdown, dial toll-free: USA: 1-800-521-2779/Canada: 1-800-363-4869.  Provide your name, Vehicle Identification Number (VIN) required for covered services, license plate number, and your location, including the telephone number from which you are calling.  Briefly describe the nature of the problem and answer a few simple questions.  You will be given the name of the service provider and an estimated time of arrival.  If you feel you are in an unsafe situation, please let us know.  With your consent,", "of arrival.  If you feel you are in an unsafe situation, please let us know.  With your consent, we will contact local police or safety authorities.  Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  What is the phone number for roadside assistance call?  The phone number is: US: 1-800-521-2779 Canada: 1-800-363-4869 If I am subscribed to SiriusXM Guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance?  No, however your new vehicle may include Roadside Assistance Call services.  FCA US LLC reserves the right to modify the terms or discontinue the Roadside Assistance Program at any time.  The Roadside Assistance", "the terms or discontinue the Roadside Assistance Program at any time.  The Roadside Assistance program is subject to restrictions and conditions of use, which are determined solely by FCA US LLC.  If Unable to Contact Roadside Assistance", "In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  EMISSIONS INSPECTION", "diesel emissions standards required by the Environmental Protection Agency.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or", "ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently", "is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button", "and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an", "Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a", "to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate", "OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.", "Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A", "vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all", "system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not", "you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON", "engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.", "Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry (If Equipped) The Passive Entry system is a feature that allows you to lock and unlock the vehicle\u2019s door(s) and tailgate without having to push the key fob lock or unlock buttons.  Note: Passive Entry may be programmed on/off through Uconnect Settings The key fob may not be detected by the vehicle Passive Entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may interfere with the key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.  Passive Entry Unlock initiates Headlight Illumination On Approach (low beams, license plate lamp, parking lights) for whichever duration is set within the Uconnect Settings between 0, 30, 60 or 90 seconds.  Passive Entry Unlock also initiates two flashes of the turn signal lights.  If wearing gloves, if it has been raining/snowing, or there is salt/dirt covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a", "covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.  The doors may unlock when water is sprayed on the Passive Entry door handles if the key fob is located outside of the vehicle within 5 ft (1.5 m) of the handle.  If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will relock and, if equipped, will arm the Vehicle Security system.  Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry (If Equipped) The Passive Entry system is a feature that allows you to lock and unlock the vehicle\u2019s door(s) and tailgate without having to push the key fob lock or unlock buttons.  Note: Passive Entry may be programmed on/off through Uconnect Settings The key fob may not be detected by the vehicle Passive Entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may interfere with the key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.", "key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.  Passive Entry Unlock initiates Headlight Illumination On Approach (low beams, license plate lamp, parking lights) for whichever duration is set within the Uconnect Settings between 0, 30, 60 or 90 seconds.  Passive Entry Unlock also initiates two flashes of the turn signal lights.  If wearing gloves, if it has been raining/snowing, or there is salt/dirt covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.  The doors may unlock when water is sprayed on the Passive Entry door handles if the key fob is located outside of the vehicle within 5 ft (1.5 m) of the handle.  If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will relock and, if equipped, will arm the Vehicle Security system.  Frequency Operated Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive", "Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.  FOBIK-Safe only executes in vehicles with Passive Entry.  There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made by a valid Passive Entry key fob while a door is open.  A lock request is made by the Passive Entry door handle while a door is open.  A lock request is made by the door panel switch while the door is open.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  Note: The", "system, the key fob protection described in this section remains active/functional.  Note: The vehicle will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle.  The vehicle will not unlock the doors when any of the following conditions are true: A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are manually locked using the door lock knobs.  Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.  To Lock The Vehicle\u2019s Doors With one of the vehicle\u2019s Passive Entry key fobs within 5 ft (1.5 m) of the driver or passenger front door handles, pushing the Passive Entry lock button will lock the vehicle doors.  Note: When pushing the door handle lock button, DO NOT grab the door handle.  This could unlock the door(s).  Note: After pushing the door handle button, the driver must wait three seconds before locking or", "Note: After pushing the door handle button, the driver must wait three seconds before locking or unlocking the doors, using any Passive Entry door handle.  This is done to allow the driver to check if the vehicle is locked by pulling the door handle without the vehicle unlocking.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in \u201cPreventing Inadvertent Locking Of Passive Entry Key Fob In Vehicle\u201d remains active/functional.  The Passive Entry system will not operate if the key fob battery is depleted  Frequency Operated Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.  FOBIK-Safe only executes in vehicles with Passive Entry.  There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made", "situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made by a valid Passive Entry key fob while a door is open.  A lock request is made by the Passive Entry door handle while a door is open.  A lock request is made by the door panel switch while the door is open.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  Note: The vehicle will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle.  The vehicle will not unlock the doors when any of the following conditions are true: A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are", "outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are manually locked using the door lock knobs.  Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.", "brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the", "to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second", "to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  Interior Courtesy Lights When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right)", "the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  To enter the \u201cPartial Off\u201d mode, momentarily push the ESC OFF button and the ESC OFF Indicator Light will illuminate.  To turn the ESC on again, momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door", "momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Automatic Headlight System will turn the headlights on or off according to ambient light levels.  To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation.  When the system is on, the headlight time delay feature is also on.  This means the headlights will stay on for up to 90 seconds (programmable through the uconnect settings \"\u21e8uconnect settings\" ) after you place the ignition into the off position.  To turn the automatic system off, move the headlight switch out of the AUTO position.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the", "The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Reduce power to unnecessary loads if possible: Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed", "settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s exterior and interior lights.  When the \u201cDaytime Running Lights\u201d feature is selected, the daytime running lights can be turned on or off.  This feature is only allowed by law in the country of the vehicle purchase.  Depending on the vehicle\u2019s options, feature settings may vary.  Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to", "lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other", "systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "Cooling System WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or", "has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is", "the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Place Hand In Hood Opening  Cooling System WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can", "fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Halogen Headlamps \u2014 If Equipped See the following steps to replace: Open hood and support using prop rod.  Remove the front grille.  Turn the retainers along the top a quarter turn counterclockwise and remove.  Pull the bottom of the grille away, starting at one side and working toward the other.  Remove the three screws holding the headlamp to the vehicle.  Remove lamp from the vehicle.  Remove the lamp from the collar.  Grab the bulb and turn a quarter turn counterclockwise.  Pull the bulb from the housing.  Push connector locking tab to the unlock position.  Remove connector from bulb.  Push connector onto new bulb base, and push the connector locking tab to the lock position.  Reinstall bulb housing.  Rotate the bulb a quarter turn clockwise.  CAUTION: Do not touch the new bulb with your fingers.  Oil contamination will severely shorten bulb life.  If", "not touch the new bulb with your fingers.  Oil contamination will severely shorten bulb life.  If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.  Note: We recommend seeing an authorized dealer for service.  Opening The Hood Release both of the outside hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Note: Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.", "Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to", "of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances", "(if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle", "repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Frequency Operated Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your", "To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.  FOBIK-Safe only executes in vehicles with Passive Entry.  There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made by a valid Passive Entry key fob while a door is open.  A lock request is made by the Passive Entry door handle while a door is open.  A lock request is made by the door panel switch while the door is open.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  Note: The vehicle will only unlock the doors", "described in this section remains active/functional.  Note: The vehicle will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle.  The vehicle will not unlock the doors when any of the following conditions are true: A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are manually locked using the door lock knobs.  Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.", "Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is", "turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Lightly push the multifunction lever up or down, without moving beyond the detent, and the turn signal will flash three times then automatically turn off.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.", "Fastener Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  To remove the Fastener Bin: Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Note: The soft top fasteners do not go in the Fastener Bin.  Rear Wall Storage Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  Fastener Bin Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  The Locking Storage Bin can be removed by unfastening the four", "the bottom of the Fastener Bin.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  To remove the Fastener Bin: Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  Remove the grommets under the front seat (one left and one right).  Carpet Split Then pull the carpet out, to the rear and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin", "and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin (if equipped), by removing the four bolts that hold it to the floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then lift the assembly out from under the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear Retainers Remove carpet from the vehicle.  When reinstalling the carpet, perform these steps in reverse order making sure that the carpet is tucked under the scuffs, B-pillar, console, and then refasten the grommets.  Inside the bin are three removable dividers to set up storage that works best for you.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  The rear wall netting can be accessed the same way as the rear wall storage", "the floor are removed.  The rear wall netting can be accessed the same way as the rear wall storage bin.  If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.", "Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This", "does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard", "hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine", "service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as", "your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Synthetic Engine Oils Your engine was designed for synthetic engine oils, only use synthetic API approved engine oils.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The", "(API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.", "Adaptive Cruise Control (ACC) Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC ACC will allow you to keep Cruise Control engaged in light to moderate traffic conditions without the constant need to reset your speed.  ACC utilizes a radar sensor and a forward-facing camera designed to detect a vehicle directly ahead of you to maintain a set speed.  Note: If the ACC sensor detects a vehicle ahead, ACC will apply limited braking or accelerate (not to exceed the original set speed) automatically to maintain a preset following distance, while matching the speed of the vehicle ahead.  Any chassis/suspension or tire size modifications to the vehicle will affect the performance of the Adaptive Cruise Control and Forward Collision Warning system.  Fixed Speed", "the performance of the Adaptive Cruise Control and Forward Collision Warning system.  Fixed Speed Cruise Control (ACC not enabled) will not detect vehicles directly ahead of you.  Always be aware of the feature selected WARNING: Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The acc system: does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be", "a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  You should turn the ACC system off and do not use: When driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.e., in highway construction zones).  When entering a turn lane or highway off-ramp; when driving on roads that are winding, icy, snow-covered, slippery, or have steep uphill or downhill slopes.  When towing a trailer up or down steep slopes.  When circumstances do not allow safe driving at a constant speed.  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.", "use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system:  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The", "major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.", "Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the", "windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the", "EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present", "will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a", "engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  When Remote Start is active, and the outside ambient temperature is 40\u00b0F (4.5\u00b0C) or below, the system will automatically activate front defrost for 15 minutes or less.  The time is dependent on the ambient temperature.  Once the timer expires, the system will automatically adjust the", "on the ambient temperature.  Once the timer expires, the system will automatically adjust the settings depending on ambient conditions.  See \u201cRemote Start Comfort Systems \u2014 If Equipped\u201d in the next section for detailed operation.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  These features will stay on through the duration of Remote Start, or until the ignition", "button.  These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.  To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations", "is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining", "uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.", "the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.", "Windshield Washers To use the washer, pull the lever toward you and hold until desired spray is reached.  If the lever is pulled while in the delay range, the wiper will start and continue to operate for two or three wipe cycles after the lever is released.  Then, the intermittent interval previously selected will resume.  If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles.  Then, the wipers will turn off.  Note: As a protective measure, the washer will stop if the switch is held for more than 20 seconds.  Once the switch is released the washer will resume normal operation.  WARNING: Sudden loss of visibility through the windshield could lead to a collision.  You might not see other vehicles or other obstacles.  To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a", "Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  Mist Push upward on the wiper", "damage to the wiper motor may occur when the vehicle is restarted.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.", "Rim Size This is the rim size that is appropriate for the tire size listed.  Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with", "= rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire.  This is the rim size that is", "the maximum permissible cold tire inflation pressure for this tire.  This is the rim size that is appropriate for the tire size listed.  P (Passenger) \u2014 Metric tire sizing is based on US design standards.  P-Metric tires have the letter \u201cP\u201d molded into the sidewall preceding the size designation.  Example: P215/65R15 95H.  European \u2014 Metric tire sizing is based on European design standards.  Tires designed to this standard have the tire size molded into the sidewall beginning with the section width.  The letter \u201cP\u201d is absent from this tire size designation.  Example: 215/65R15 96H.  LT (Light Truck) \u2014 Metric tire sizing is based on US design standards.  The size designation for LT-Metric tires is the same as for P-Metric tires except for the letters \u201cLT\u201d that are molded into the sidewall preceding the size designation.  Example: LT235/85R16.  Temporary spare tires are designed for temporary emergency use only.  Temporary high pressure compact spare tires have the letter \u201cT\u201d or \u201cS\u201d molded into the sidewall", "Temporary high pressure compact spare tires have the letter \u201cT\u201d or \u201cS\u201d molded into the sidewall preceding the size designation.  Example: T145/80D18 103M.  High flotation tire sizing is based on US design standards and it begins with the tire diameter molded into the sidewall.  Example: 31x10.5 R15 LT. The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in", "tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl", "load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire full size spare \u2014 if equipped the full size spare is for temporary emergency use only.  This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not.  This spare tire may have limited tread life.  When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced.  Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity.", "Adding Washer Fluid The fluid reservoir is located in the engine compartment.  Be sure to check the fluid level at regular intervals.  Fill the reservoir with windshield washer solvent only (not radiator antifreeze).  When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades; this will help blade performance.  To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate.  This rating information can be found on most washer fluid containers.  WARNING: Commercial windshield washer solvents are flammable.  They could ignite and burn you.  Care must be exercised when filling or working around the washer solution.  1 \u2014 Power Distribution Center (Fuses) 6 \u2014 Brake Fluid Reservoir Cap 2 \u2014 Battery 7 \u2014 Engine Air Cleaner Filter 3 \u2014 Engine Oil Dipstick 8 \u2014 Power Steering Fluid Reservoir Cap 4 \u2014 Engine Oil Fill 9 \u2014 Washer Fluid Reservoir Cap 5 \u2014", "8 \u2014 Power Steering Fluid Reservoir Cap 4 \u2014 Engine Oil Fill 9 \u2014 Washer Fluid Reservoir Cap 5 \u2014 Engine Coolant Pressure Cap 1 \u2014 Battery 6 \u2014 Power Distribution Center (Fuses) 2 \u2014 Engine Oil Fill 7 \u2014 Power Steering Reservoir Cap 3 \u2014 Coolant Pressure Reservoir Cap 8 \u2014 Engine Oil Dipstick 4 \u2014 Brake Fluid Reservoir Cap 9 \u2014 Engine Air Cleaner Filter 5 \u2014 Washer Fluid Reservoir Cap Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Fluid Level Check Check the fluid level by removing the fill plug.  The fluid level should be between the bottom of the fill hole and a point not more than 3/16 of an inch (4.76 mm) below the bottom of the hole.  Add fluid, if necessary, to maintain the proper level.  Fluid Level Check The fluid level should be", "Add fluid, if necessary, to maintain the proper level.  Fluid Level Check The fluid level should be to the bottom edge of the fill hole when the vehicle is in a level position.  Fluid Level Check \u2014 Brake Master Cylinder The fluid level of the master cylinder should be checked whenever the vehicle is serviced, or immediately if the Brake System Warning Light is on.  If necessary, add fluid to bring level within the designated marks on the side of the reservoir of the brake master cylinder.  Be sure to clean the top of the master cylinder area before removing cap.  With disc brakes, fluid level can be expected to fall as the brake pads wear.  Brake fluid level should be checked when pads are replaced.  If the brake fluid is abnormally low, check the system for leaks.  For further information WARNING: Use only manufacturer recommended brake fluid Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance.  The proper type of brake fluid for your vehicle is also", "system and/or impair its performance.  The proper type of brake fluid for your vehicle is also identified on the original factory installed hydraulic master cylinder reservoir.  To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container.  Keep the master cylinder reservoir cap secured at all times.  Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point.  This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure.  This could result in a collision.  Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire.  Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces.  Do not allow petroleum based fluid to contaminate the brake fluid.  Brake seal components could be damaged, causing partial or complete brake failure.", "brake fluid.  Brake seal components could be damaged, causing partial or complete brake failure.  This could result in a collision.", "Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be", "these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the", "upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside),", "Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.", "or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels", "top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Remove both front panels Open both front doors.  Using the provided #50 Torx head driver and ratchet, remove the two Torx head", "both front doors.  Using the provided #50 Torx head driver and ratchet, remove the two Torx head screws that secure the hard top at the B-pillar (near the top of the front doors).  Step Three If equipped, remove the lower interior soft trim panel (attached by the hook-and-loop fastener) by pulling the panel away from the trim.  Step Four Remove the Torx head fasteners that secure the hard top to the vehicle: two along the interior body side, rearward of the back doors, followed by the four fasteners along the back of the vehicle cab using the #T50 Torx head driver.  Step Five 1 \u2014 Vehicle Cab Torx Head Fasteners 2 \u2014 Body side Torx Head Fasteners Locate the wire harness on the left rear inside corner of the vehicle.  To access the harness, remove the plastic cover by pushing the cover to the side, and sliding it off.  Do not force open; this will break the plastic cover.  Step Six To release the wire harness, pull back on the red latch (1), then push down on the black button (2) while pulling the harness out.", "back on the red latch (1), then push down on the black button (2) while pulling the harness out.  Step Seven 1 \u2014 Red Latch 2 \u2014 Black Button Remove the hard top from the vehicle.  Install the provided edge protectors along the bottom edges of the hard top, and place the hard top on a soft surface to prevent damage.  The removal of the Hard Top requires four adults located on each corner.  Failure to follow this caution could damage the Hard Top.  Store the wire harness by removing the storage cover on the quarter trim.  Use the mechanical key blade to pry the cover open.  Step Nine Tuck the wire harness inside the storage compartment, and replace the cover.", "If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you", "prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides", "a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is", "may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  FOLDING WINDSHIELD The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element provides.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving", "the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  WARNING: Carefully follow these warnings to help protect against personal injury: Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these", "fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "Disposal Of Used Coolant Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh", "in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  ENGINE FLUIDS AND LUBRICANTS CAUTION: Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic", "coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Note: If the vehicle is exposed to extreme cold", "engine coolant (antifreeze) is not recommended.  Note: If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  It is the owner's responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.", "freezing according to the temperatures occurring in the area where the vehicle is operated.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system, please contact an authorized dealer.  Mixing engine coolant types is not recommended and can result in cooling system damage.  If HOAT and OAT coolant are mixed in an emergency, have an authorized dealer drain, flush, and refill with OAT coolant (conforming to MS.90032) as soon as possible.  Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system", "a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease", "Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Please review these", "Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Please review these recommendations for using Organic Additive Technology (OAT) engine coolant that meets the requirements of the manufacturer Material Standard MS.90032.  When adding engine coolant (antifreeze): The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  The tongue weight of the trailer The weight of any other type of cargo or equipment put in or on your vehicle The weight of the driver and all passengers For further information on GAWRs, vehicle loading, and trailer towing, see If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OAT coolant (conforming to MS.90032).  It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the Run Flat mode.  Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine", "of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill", "is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.", "See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you", "See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.", "will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Jack Location The jack and tools are stored under the right rear seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools", "seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat.  Removing the wing bolt release the tool bag straps from the jack and remove tools from bag.  Jack and tool bag remove tool kit and assemble tools.  Jack And Tool Bag There are two ways to assemble the tools: Note: If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  CAUTION: The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools, always reinstall them in the original carrier and location.  While", "After using the jack and tools, always reinstall them in the original carrier and location.  While driving you may experience abrupt stopping, rapid acceleration or sharp turns.  A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.", "ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are", "in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the", "starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to", "ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or", "it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.", "Connected Services Roadside Assistance FAQs What is the phone number for roadside assistance call?  The phone number is: us: 1-800-521-2779 canada: 1-800-363-4869 if i am subscribed to siriusxm guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance.  No, however your new vehicle may include Roadside Assistance Call services.  What to Do If your vehicle requires jump start assistance, out of gas/fuel delivery, tire service, lockout service or towing as a result of a mechanical breakdown, dial toll-free: USA: 1-800-521-2779/Canada: 1-800-363-4869.  Provide your name, Vehicle Identification Number (VIN) required for covered services, license plate number, and your location, including the telephone number from which you are calling.  Briefly describe the nature of the problem and answer a few simple questions.  You will be given the name of the service provider and an estimated time of arrival.  If you feel you are in an unsafe situation, please let us know.  With your consent,", "of arrival.  If you feel you are in an unsafe situation, please let us know.  With your consent, we will contact local police or safety authorities.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.", "Replacing The Battery In The Key Fob The recommended replacement battery is CR2450.  Remove the back cover of the key fob by inserting a flat-blade screwdriver into the slot on the bottom of the fob.  Apply light pressure until the cover unsnaps being careful not to damage the seal.  Proceed counterclockwise (in the order shown in the following image) to loosen the remaining snaps until the battery cover can be removed.  1-3 \u2013 back cover pry points remove the depleted battery by inserting a small flat-blade screwdriver into the battery removal slot and sliding the battery forward and upward being careful not to damage the electronic board underneath.  Battery replacement install the new battery into the key fob, making sure the positive (+) side is facing up.  Slide the battery until it is seated securely below the tabs.  Reassemble the back cover making sure it is properly aligned before snapping it back in place.  Note: Customers are recommended to use a battery obtained from Mopar\u00ae.  Aftermarket coin", "in place.  Note: Customers are recommended to use a battery obtained from Mopar\u00ae.  Aftermarket coin battery dimensions may not meet the original OEM coin battery dimensions.  Perchlorate material \u2014 special handling may apply.  See www.dtsc.ca.gov/hazardouswaste/perchlorate for further information.  Do not touch the battery terminals that are on the back housing or the printed circuit board.  When a key fob battery is low, a warning will be indicated on the vehicle\u2019s instrument cluster, and the fob LED will no longer illuminate with a button push.  WARNING: The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop", "and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.", "facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical", "integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  The battery in your vehicle is located in the right rear of the engine compartment.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  The Power Distribution Center is located", "on the passenger side under the instrument panel.  The Power Distribution Center is located in the engine compartment near the battery.  This center contains cartridge fuses, mini fuses, and relays.  The PDC top cover is labeled with each serviceable fuse/relay location, function, and size.", "Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  WARNING: Fast spinning tires can be dangerous.  Forces generated by excessive wheel speeds may cause tire damage or failure.  A tire could explode and injure someone.  Do not spin your vehicle's wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.  Off-Road Driving Tips  When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your", "dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and", "automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the", "any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.", "Materials Added To Fuel Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Designated TOP TIER Detergent Gasoline contains a higher level of detergents to further aide in minimizing engine and fuel system deposits.  When available, the usage of TOP TIER Detergent Gasoline is recommended.  Visit www.toptiergas.com for a list of top tier detergent gasoline retailers.  Indiscriminate use of fuel system cleaning agents should be avoided.  Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients.  These can harm fuel system gasket and diaphragm materials.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.", "to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Biodiesel fuel may gel or solidify at low ambient temperatures, which may pose problems for both storage and operation.  Precautions can be necessary at low ambient temperatures, such as storing the fuel in a heated building or a heated storage tank, or using cold temperature additives.  Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from", "fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition", "and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  Methylcyclopentadienyl Manganese Tricarbonyl (MMT) In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasolines to increase octane.  Gasoline", "metallic additive that is blended into some gasolines to increase octane.  Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT.  Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles.  The manufacturer recommends that gasoline without MMT be used in your vehicle.  The MMT content of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gasoline retailer whether the gasoline contains MMT.  MMT is prohibited in Federal law and California reformulated gasoline.", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.", "brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the", "to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second", "to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWRWARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make", "of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  For further information on GAWRs, vehicle loading, and trailer towing, see", "When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD", "REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted", "the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to", "is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High,", "view is pressed.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.", "Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the", "Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the", "or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.  INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the", "vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.", "Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Note: Vehicle speeds shown in the preceding chart are for 2H and 4H only.  Vehicle speeds in 4L would be significantly less.  To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Make certain that the load is secured in the trailer and that it will not shift during travel.  When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.  You could lose control of", "load shifts can occur that may be difficult for the driver to control.  You could lose control of your vehicle and have a collision.  When hauling cargo, or towing a trailer, do not overload your vehicle or trailer.  Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.  Safety chains must always be used between your vehicle and trailer.  Always connect the chains to the frame or hook retainers of the vehicle hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be parked on a grade.  When parking, apply the parking brake on the tow vehicle.  Put the tow vehicle transmission in PARK.  Always block or \"chock\" the trailer wheels.  GCWR must not be exceeded.  Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: GVWR GTW GAWR Tongue weight rating for the trailer", "the following four ratings are not exceeded: GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing a heavy trailer), use the AutoStick shift control to select a lower gear Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Note: Vehicle speeds shown in the preceding chart are for 2H and 4H only.  Vehicle speeds in 4L would be significantly less.  Manual transmission shift speeds in mph (km/h)", "Vehicle speeds in 4L would be significantly less.  Manual transmission shift speeds in mph (km/h) engine speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.6l accel.  15 (24) 24 (39) 50 (80) 65 (104) 70 (112) cruise 10 (16) 19 (31) 40 (64) 55 (88) 65 (105) 8\u2013speed automatic transmission the transmission gear range (prndm) is displayed both beside the gear selector and in the instrument cluster.  To select a gear range, push the lock button on the gear selector and move the selector rearward or forward.  To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.  You must also press the brake pedal to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is stopped or moving at low speeds.  Select the DRIVE range for normal driving.  The electronically controlled transmission adapts its shift schedule based on driver inputs, along with environmental and road conditions.  The transmission electronics are self-calibrating; therefore, the first few shifts on a new", "The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt.  This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers).  Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped.  Be sure to keep your foot on the brake pedal when shifting between these gears.  The transmission gear selector provides PARK, REVERSE, NEUTRAL, DRIVE and MANUAL (AutoStick) shift positions.  Manual shifts can be made using the AutoStick shift control.  Toggling the gear selector forward (-) or rearward (+) while in the MANUAL (AutoStick) position (beside the DRIVE position) will manually select the transmission gear, and will display the current gear in the instrument cluster Note: In the event of a mismatch between the gear selector position and the actual transmission gear (for example, driver selects PARK while driving), the position indicator will blink continuously", "(for example, driver selects PARK while driving), the position indicator will blink continuously until the selector is returned to the proper position, or the requested shift can be completed.  Note: If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action", "function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After", "Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected", "conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Service ACC/FCW Warning If the system turns off, and the instrument cluster display reads \u201cACC/FCW Unavailable Service Required\u201d or \u201cCruise/FCW Unavailable Service Required\u201d, there may be an internal system fault or a temporary malfunction that limits ACC functionality.  Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.  If this occurs, try activating ACC again later, following an ignition cycle.  If the problem persists, see an authorized dealer.  Your vehicle may be equipped with a protective cover that is to be used whenever the windshield is folded down in order to protect the ACC/FCW sensor.  To install the cover, refer to the following instructions: If the \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the radar sensor realigned at an authorized dealer.  The \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d warning will display and a chime", "dealer.  The \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d warning will display and a chime will sound when conditions temporarily limit system performance.  Always keep the sensor clean.  Carefully wipe the sensor lens with a soft cloth.  Be cautious not to damage the sensor lens.  Do not remove any screws from the sensor.  Doing so could cause an ACC system malfunction or failure and require a sensor realignment.  If the sensor or front end of the vehicle is damaged due to a collision, see an authorized dealer for service.  Do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles.  Doing so could cause an ACC system failure or malfunction.  If the \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d warning is active, Fixed Speed Cruise Control is still available.  The \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d warning will display and a chime will sound when conditions temporarily limit system performance.  This most often occurs at times of poor", "when conditions temporarily limit system performance.  This most often occurs at times of poor visibility, such as in snow or heavy rain and fog.  The ACC system may also become temporarily blinded due to obstructions, such as mud, dirt, or ice on windshield and fog on the inside of glass.  In these cases, the instrument cluster display will read \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d and the system will have degraded performance.  If the instrument cluster displays \u201cACC/FCW Limited Functionality\u201d or \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d momentarily, there may be a condition that limits FCW functionality.  Although the vehicle is still drivable under normal conditions, the active braking may not be fully available.  Once the condition that limited the system performance is no longer present, the system will return to its full performance state.  If the problem persists, see an authorized dealer.  If the system turns off, and the instrument cluster display reads \u201cACC/FCW", "an authorized dealer.  If the system turns off, and the instrument cluster display reads \u201cACC/FCW Unavailable Service Required\u201d or \u201cCruise/FCW Unavailable Service Required\u201d, there may be an internal system fault or a temporary malfunction that limits ACC functionality.  Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.  If this occurs, try activating ACC again later, following an ignition cycle.  If the problem persists, see an authorized dealer.  This message can sometimes be displayed while driving in adverse weather conditions.  The ACC/FCW system will recover after the vehicle has left these areas.  Under rare conditions, when the camera is not tracking any vehicles or objects in its path this warning may temporarily occur.  Changing the FCW status to \u201cOnly Warning\u201d prevents the system from providing limited active braking, or additional brake support if the driver is not braking adequately in the event of a potential frontal collision, but maintains the", "driver is not braking adequately in the event of a potential frontal collision, but maintains the audible and visual warnings.  Changing the FCW status to \u201cOff\u201d prevents the system from providing autonomous braking, or additional brake support if the driver is not braking adequately in the event of a potential frontal collision.  The system will retain the last setting selected by the driver after ignition shut down.  FCW may not react to irrelevant objects such as overhead objects, ground reflections, objects not in the path of the vehicle, stationary objects that are far away, oncoming traffic, or leading vehicles with the same or higher rates of speed.  FCW will be disabled like ACC, with the unavailable screens.  Driver Assist \u2014 If Equipped The Driver Assist menu displays the status of the ACC system.  Push and release the up or down arrow button until the driver assist menu is displayed in the instrument cluster display.", "To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c.20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately", "your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov .  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the", "has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved", "is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not", "5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.", "Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.  Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle.  These kinds of hitches are commonly used to tow small and medium sized trailers.  Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.  Trailer hitch classification definitions class max.  Trailer hitch industry standards class i - light duty 2,000 lb (907 kg) class ii - medium duty 3,500 lb (1,587 kg) class iii - heavy duty 6,000 lb (2,722 kg) class iv - extra heavy duty 10,000 lb", "lb (1,587 kg) class iii - heavy duty 6,000 lb (2,722 kg) class iv - extra heavy duty 10,000 lb (4,535 kg) refer to the \u201ctrailer towing weights (maximum trailer weight ratings)\u201d chart for the maximum gross trailer weight (gtw) towable for your given drivetrain in this section.  All trailer hitches should be professionally installed on your vehicle.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch", "and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.", "The ignition switch must be in the ACC or ON/RUN position to adjust the power mirrors.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the", "unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP", "is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: The message will stay active until the ignition is placed in the ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster", "START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  To insert an Auxiliary device, gently insert the Auxiliary device cable into the AUX port.  If you insert an Auxiliary device with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system will automatically time out and the ignition will cycle to the OFF position after 30", "The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn", "is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, see These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.", "If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is", "center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator,", "After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough", "not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up", "high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.", "Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A", "vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all", "system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not", "you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition", "for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition", "or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.", "If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  OFF ROAD+ will not function in Two-Wheel Drive High (2H) mode.  If the button is pushed while in 2H mode, the cluster display will show the message \u201cOFF ROAD+ Unavailable Shift to 4WD\u201d.  The ASSIST button is used to automatically connect you to any one of the following support centers: Once the 4G Wi-Fi Hotspot is purchased, you can change its name and the password by selecting the Wi-Fi Hotspot App and pressing the Setup Wi-Fi Hotspot button.  You can also view the connected devices from the app screen by pressing the View Connected Devices button.  If equipped, the ASSIST Button is used for contacting", "pressing the View Connected Devices button.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  1 \u2014 Assist Button 2 \u2014 SOS Button The driver should NEVER use the 4G Wi-Fi Hotspot while driving the vehicle as doing so may result in an accident involving serious injury or death.  ASSIST AND SOS SYSTEM \u2014 IF EQUIPPED If equipped, the overhead console contains an ASSIST and an SOS button.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the", "ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  ASSIST AND SOS SYSTEM \u2014 IF EQUIPPED If equipped, the overhead console contains an ASSIST and an SOS button.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering", "traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  Off Road+ Display \u2014 If Equipped When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will", "messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: 2h: off road+ unavailable, shift to 4wd 4h: 4wd high off road+ active 4l: 4wd low off road+ active adaptive cruise control (acc) and cruise control are not available when using off road+.  If either option is selected, a dedicated message will display indicating that the features are not usable concurrently.  Messages are as follows: 4h: cruise control \u2014 cruise control unavailable in off road+ 4h: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in off road+ 4l: cruise control \u2014 cruise control unavailable in 4wd low 4l: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in 4wd low note: the behavior of electronic stability control while in off road+ varies depending on the 4wd status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also,", "4wd status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also, holding the ESC OFF button for five seconds will turn off ESC.  In 4WD Low, Electronic Stability Control automatically shuts off regardless of the Off Road Status.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons", "The Jeep\u00ae wireless speaker is located behind the right rear passenger seat.  In order to access the Jeep\u00ae wireless speaker, the seat will need to be folded down or tilted forward.  A feature of the Jeep\u00ae wireless speaker is the ability for the Jeep\u00ae wireless speaker to connect to devices using Bluetooth\u00ae.  Follow these simple steps to connect a Bluetooth\u00ae-enabled device to the Jeep\u00ae wireless speaker: To remove the Jeep\u00ae wireless speaker, pull on the strap located on top of the mount for the speaker.  When the strap is pulled, the Jeep\u00ae wireless speaker can easily be lifted from the mount.  Jeep\u00ae Wireless Speaker Location The Jeep\u00ae wireless speaker is located behind the right rear passenger seat.  In order to access the Jeep\u00ae wireless speaker, the seat will need to be folded down or tilted forward.  To remove the Jeep\u00ae wireless speaker, pull on the strap located on top of the mount for the speaker.  When the strap is pulled, the Jeep\u00ae wireless speaker can easily be lifted from the mount.  When placing the", "strap is pulled, the Jeep\u00ae wireless speaker can easily be lifted from the mount.  When placing the Jeep\u00ae wireless speaker back in the mount, simply put the speaker back in the mount.  Then push/rotate forward on the front of the speaker until the speaker locks in place.  Charging The Speaker Before using the Jeep\u00ae wireless speaker for the first time, fully charge your Jeep\u00ae wireless speaker until the battery indicator light stays solid green.  The Jeep\u00ae wireless speaker in-vehicle dock is the most ideal way to fully charge the speaker with the ignition in ON/RUN or ACC.  The speaker can also be charged with a power adapter.  To charge the Jeep\u00ae wireless speaker with a power adapter, insert the power adapter into a wall outlet.  Next, plug the power adapter into the Jeep\u00ae wireless speaker charging port on the back of the speaker.  Note: Jeep\u00ae wireless speaker will not charge within vehicle dock while the ignition is fully off.  Note: Power adapter needed for the Jeep\u00ae wireless speaker has to have a range of", "is fully off.  Note: Power adapter needed for the Jeep\u00ae wireless speaker has to have a range of 14 VDC to 16.5 VDC, with a minimum of 2.7A and a barrel connector dimension of 5.5 mm by 2.5 mm.  Power adapter is not included.", "Safety Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.  WARNING: Improperly inflated tires are dangerous and can cause collisions.  Underinflation increases tire flexing and can result in overheating and tire failure.  Overinflation reduces a tire's ability to cushion shock.  Objects on the road and chuckholes can cause damage that result in tire failure.  Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.  Unequal tire pressures can cause steering problems.  You could lose control of your vehicle.  Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.  Always drive with each tire inflated to the recommended cold tire inflation pressure.  Note: Unequal tire pressures from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure", "from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure from side to side may cause the vehicle to drift left or right.  FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.", "turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of", "load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure", "abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Temperature Grades The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not", "The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.  Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.", "Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety", "any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html frequently asked questions about installing child restraints with seat belts what is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor", "is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward-facing child restraint, up to the recommended weight limit of the child restraint.  Can the rear-facing child restraint touch the back of the front passenger seat?  Yes contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.  Can the rear head restraints be removed?  Yes the center head restraint can be removed if it interferes with the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint?  No do not twist the buckle stalk in a seating position with an alr retractor.  Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and", "Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.  Use this simple 5-step test to decide whether the child can use the vehicle\u2019s seat belt alone: Can the child sit all the way back against the back of the vehicle seat?  Do the child\u2019s knees bend comfortably over the front of the vehicle seat while the child is still sitting all the way back?  Does the shoulder belt cross the child\u2019s shoulder between the neck and arm?  Is the lap part of the belt as low as possible, touching the child\u2019s thighs and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to any of these questions was \u201cno,\u201d then the child still needs to use a booster seat in this vehicle.  If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s", "belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s squirming or slouching can move the belt out of position.  If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.  WARNING: Never allow a child to put the shoulder belt under an arm or behind their back.  In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.  A child must always wear both the lap and shoulder portions of the seat belt correctly.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to", "12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter", "hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  Important Safety Precautions Please pay close attention to the information in this section.  It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.  Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: Children 12 years old and under should always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be", "with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint Never allow children to slide the shoulder belt behind them or under their arm.  You should read the instructions provided with your child restraint to make sure that you are using it properly.  All occupants should always wear their lap and shoulder belts properly.  The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate.  Do not lean against the door or window.  If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.  If the air bag system in", "the space between occupants and the door and occupants could be injured.  If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see \"\u21e8if you need assistance\" for customer service contact information.  WARNING: Never place a rear-facing child restraint in front of an air bag.  A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.  Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing child restraint in the rear seat.  If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle.", "To Arm The System Follow these steps to arm the Vehicle Security system: Make sure the vehicle\u2019s ignition is placed in the OFF position.  Perform one of the following methods to lock the vehicle: push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zonePush the lock button on the key fob.  If any doors are open, close them.  Note: The Vehicle Security system will not arm if you lock the doors using the manual door lock.  To Arm The System Follow these steps to arm the Vehicle Security system: Make sure the vehicle\u2019s ignition is placed in the OFF position.  Perform one of the following methods to lock the vehicle: push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone Push the", "Passive Entry door handle with a valid key fob available in the same exterior zone Push the lock button on the key fob.  If any doors are open, close them.  Note: The Vehicle Security system will not arm if you lock the doors using the manual door lock.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic,", "disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two", "but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle", "When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Conditions that will cause the engine to start automatically while in stop/start autostop active mode, the engine will start automatically when: actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode stop/start autostop active time exceeds five minutes battery voltage drops too low vehicle is moving faster than 5 mph (8 km/h) stop/start off switch is pressed transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold (ess models only) to start the engine while in autostop mode while in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is pressed.  The transmission will automatically re-engage upon engine restart.  Conditions that will cause the engine to start automatically while in autostop mode: the transmission selector is moved out of drive to maintain cabin temperature comfort actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to", "cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode hvac system temperature or fan speed is manually adjusted battery voltage drops too low stop/start off switch is pushed a stop/start system error occurs stop/start autostop active time exceeds five minutes transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold.  Conditions that will cause the engine to start automatically while in stop/start autostop active mode, the engine will start automatically when: actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode stop/start autostop active time exceeds five minutes battery voltage drops too low vehicle is moving faster than 5 mph (8 km/h) stop/start off switch is pressed transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold (ess models only).  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.", "The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine", "will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24", "by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).", "When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.", "jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or", "with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash", "other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.", "connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the", "post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.", "Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201dWARNING:", "Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201dWARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may", "safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle", "unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for", "switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned", "operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates", "temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine", "for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be", "when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool;", "upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a", "indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the", "switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.", "What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be", "cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  What", "as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations", "effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Wheel And Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Your wheels are susceptible to deterioration caused by salt, sodium chloride, magnesium chloride, calcium chloride, etc., and other road chemicals used to melt ice or control dust on dirt roads.  Use a soft cloth or sponge and mild soap to wipe away promptly.  Do not use harsh chemicals or a stiff brush.  They can damage the wheel\u2019s protective coating that helps keep them from corroding and tarnishing.  When cleaning extremely dirty wheels, including", "helps keep them from corroding and tarnishing.  When cleaning extremely dirty wheels, including excessive brake dust, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels.  Mopar\u00ae Wheel Treatment or Mopar\u00ae Chrome Cleaner, or their equivalent, is recommended or select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels.  CAUTION: Avoid products or automatic car washes that use acidic solutions or strong alkaline additives or harsh brushes.  Many aftermarket wheel cleaners and automatic car washes may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  CAUTION: Do not use scouring pads, steel wool, a bristle brush, metal polishes, or oven cleaner.  These products may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner", "is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  Note: If you intend parking or storing your vehicle for an extended period after cleaning the wheels with wheel cleaner, drive your vehicle and apply the brakes to remove the water droplets from the brake components.  This activity will remove the red rust on the brake rotors and prevent vehicle vibration when braking.", "If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  When parking on a hill, apply the parking brake before shifting the transmission to PARK.  As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel", "Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce,", "the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.", "requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the", "headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start", "the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the", "system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.", "Feature description controls \u2014 if equipped press the controls button to access vehicle-specific features like heated seats and steering wheel.  Apps press the apps button to access a list of the available mobile apps.  Climate press the climate button to enter climate mode and access the climate control functions.  Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF.  Climate Control OFF Button Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  Feature description controls \u2014 if equipped press the controls button to access vehicle-specific features like heated seats and steering wheel.  Apps press the apps button to access a list of the available mobile apps.  Climate press the climate button to enter climate mode and access the climate control functions \"\u21e8climate controls\" .  Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF.", "Maintenance Plan Refer to the maintenance plan for the required maintenance intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to prevent premature wear.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Maintenance Plan \u2014 Diesel Fuel Up To B5 Biodiesel Refer to the Maintenance Plans for required maintenance.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly", "ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Drain And Refill For the proper maintenance intervals  Maintenance Plan \u2014 Diesel Fuel Up To B5 Biodiesel Refer to the Maintenance Plans for required maintenance.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Maintenance Plan Refer to the maintenance plan for the required maintenance intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to", "intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to prevent premature wear.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.", "AutoStick AutoStick is a driver-interactive transmission feature providing manual shift control, giving you more control of the vehicle.  AutoStick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance.  This feature can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.  Operation To activate AutoStick mode, move the gear selector into the MANUAL (M) position (beside the DRIVE position).  The current transmission gear will be displayed in the instrument cluster.  In AutoStick mode, you can use the gear selector (in the MANUAL position) to manually shift the transmission.  Tapping the gear selector forward (-) while in the MANUAL (M) position will downshift the transmission to the next lower gear.  Tapping the selector rearward (+) will command an upshift.  In AutoStick mode, the transmission will shift up or down when (+/-) is manually", "an upshift.  In AutoStick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result.  It will remain in the selected gear until another upshift or downshift is chosen, except as follows: The transmission will automatically downshift as the vehicle slows (to prevent engine lugging) and will display the current gear.  The transmission will automatically downshift to FIRST gear when coming to a stop.  After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or THIRD gear, in 4L range).  Tapping (+) (at a stop) will allow starting in SECOND gear.  Starting out in SECOND or THIRD gear can be helpful in snowy or icy conditions.  If a requested downshift would cause the engine to overspeed, that shift will not occur.  The system will ignore attempts to upshift at too low of a vehicle speed.  Holding the gear selector in", "system will ignore attempts to upshift at too low of a vehicle speed.  Holding the gear selector in the (-) position will downshift the transmission to the lowest gear possible at the current speed.  Transmission shifting will be more noticeable when AutoStick is enabled.  The system may revert to automatic shift mode if a fault or overheat condition is detected.  To disengage AutoStick mode, return the gear selector to the DRIVE position.  You can shift in or out of the AutoStick position at any time without taking your foot off the accelerator pedal.  Note: When Hill Descent Control is enabled, AutoStick is not active.  WARNING: Do not downshift for additional engine braking on a slippery surface.  The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury.  When using the AutoStick shift control, select the highest gear that allows for adequate performance and avoids frequent downshifts.  For example, choose \u201c5\u201d if the desired speed can be maintained.  Choose", "frequent downshifts.  For example, choose \u201c5\u201d if the desired speed can be maintained.  Choose \u201c4\u201d or \u201c3\u201d if needed to maintain the desired speed.  To prevent excess heat generation, avoid continuous driving at high RPM.  Return to a higher gear or vehicle speed when grade and road conditions allow.  Pushing the set (+) , or set (-) button once will result in a 1 km/h speed adjustment.  Each subsequent tap of the button results in an adjustment of 1 km/h.  If the button is continually pushed, the set speed will continue to adjust in 10 km/h increments until the button is released, then the new set speed will be established.  Pushing the set (+) , or set (-) button once will result in a 1 km/h speed adjustment.  Each subsequent tap of the button results in an adjustment of 1 km/h.  If the button is continually pushed, the set speed will continue to adjust in 10 km/h increments until the button is released,The new set speed is reflected in the instrument cluster display.", "Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  When vehicle speed becomes too high to display the pitch and roll, \u201c- -\u201d will display in place of the numbers, and the graphic will be grayed out.  A message indicating the necessary speed for the feature to become available will also display.  The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  When the Display button is pressed on the touchscreen, the system will display the options related to the theme (if equipped), brightness, and color of the touchscreen.  The available settings are: Depending on the vehicle\u2019s options, feature settings may vary.  Touchscreen The Automatic Dimming feature can be turned on or off through", "settings may vary.  Touchscreen The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Push the blue button on the faceplate or touchscreen or press and slide the temperature bar towards the blue arrow button on the touchscreen for cooler temperature settings.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directions When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the", "begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: Become familiar with the Uconnect features and applications in this vehicle before you drive on the roadway so using Uconnect will be more intuitive and will not require prolonged viewing of the screen while you are driving.  When driving, looking at the touchscreen should only be done by a glance when safe to do so.  If prolonged viewing of the screen is required, choose a safe and secure location where you can pull over and park safely to do so.  Stop use immediately if a problem occurs.  Failure to do so may cause injury or damage to the product.  See an authorized dealer for repair.  Ensure the volume level of the system is set to a level that still allows you to hear outside traffic and emergency vehicles.  When making a selection, only press one button at a time to enter the desired menu.", "vehicles.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase", "are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster", "Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to", "buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.", "Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  WARNING: Fast spinning tires can be dangerous.  Forces generated by excessive wheel speeds may cause tire damage or failure.  A tire could explode and injure someone.  Do not spin your vehicle's wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.  When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering,", "grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D)", "push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely", "and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Downhill Before driving down a steep hill, you need to determine if it is too steep for a safe descent.  What is the surface traction?  Is the grade too steep to maintain a slow, controlled descent?  Are there obstacles?  Is it a straight descent?  Is there plenty of distance at the base of the hill to regain control if the vehicle descends too fast?  If you feel confident", "at the base of the hill to regain control if the vehicle descends too fast?  If you feel confident in your ability to proceed, then make sure you are in 4L and proceed with caution.  Allow engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: Do not descend a steep grade in NEUTRAL.  Use vehicle brakes in conjunction with engine braking.  Descending a grade too fast could cause you to lose control and be seriously injured or killed.  Off-Road Driving Tips", "The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  To install the sunrider\u00ae soft top, proceed as follows: lowering the soft top \u00b9 use this qr code to access your digital experience.  Lowering The Soft Top Into The Sunrider\u00ae Position: From the Sunrider\u00ae Position, remove straps if previously secured.  Step One Failure to follow the next steps could result in damage to the soft top or vehicle.  Using the side link, lift and push the soft top toward the front of the vehicle, manually guiding the top into the closed position.  Step Two Step Two From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Step Three Pull the handle back upward while squeezing the hook, locking the latch into place.  Lowering the soft top into the sunrider\u00ae position: lowering the soft top \u00b9 use this qr code to access your digital experience.  Fold both sun visors forward against", "top \u00b9 use this qr code to access your digital experience.  Fold both sun visors forward against the windshield.  Release the header latches from the crossbar by pulling the handle downward.  Make sure the hook is fully disengaged from its receiver.  Step two from both the left and right sides, lift up on the #1 bow of the soft top to begin the operation.  It is recommended to utilize two people for this procedure.  Step three move to the side of the vehicle and use the side link to fold the soft top rearward.  Step four secure the top in this position by using the two hook-and-loop fasteners provided in the center console.  Step Five Note: The vehicle can be driven in the Sunrider\u00ae Position with the rear window and quarter panel cover assemblies fully installed or completely removed.  CAUTION: Quarter panel cover assemblies and rear window must be either all in or all out.  Removing the soft top removing the soft top \u00b9 use this qr code to access your digital experience.  Fully lower the soft top to the", "the soft top \u00b9 use this qr code to access your digital experience.  Fully lower the soft top to the Sunrider\u00ae positionCaution: failure to follow the next steps could result in damage to the soft top or vehicle.  Using the provided #T50 Torx head driver and ratchet, unscrew the two Torx head fasteners on the inside of each top mechanism.  Step two utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle\u2019s sport bar and trim.  Store the soft top in a safe, clean, and dry location.  Remove the door frames.  The rear door frames must be removed before the front door framesUsing the provided #T50 Torx head driver and ratchet, unscrew the six Torx head fasteners on both rear corners and the back of the cab, then remove the belt rail.  Note: folding down the rear seats is recommended to provide easier access to the fasteners.  Step five 1 \u2014 corner fasteners 2 \u2014 rear fasteners.", "Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d", "and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.", "of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear", "Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as", "bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and", "up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up", "the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear", "can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.", "Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d", "and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.", "of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear", "Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as", "bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.", "Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Follow the recommended maintenance intervals as shown in the Maintenance Schedule in this section.  For the proper maintenance intervals The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.  Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message  SCHEDULED SERVICING \u2014 GASOLINE ENGINE", "other than an authorized dealer, to reset the message  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will", "cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.", "The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  Power Door Lock Switch Push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone Push the lock button on the key fob.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked", "injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control", "will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Rear Seat Unoccupied Indicator Light \u2014 If Equipped This light indicates when the rear passenger seats are unoccupied, and will illuminate in the upper right portion of the instrument cluster display, momentarily replacing the configurable corner information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back", "by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are", "to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure", "using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the", "will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Trailer And Tongue Weight Never exceed the maximum tongue weight stamped on your bumper or trailer hitch.  Consider the following items when computing the weight on the rear axle of the vehicle: the tongue weight of the trailer the weight of any other type of cargo or equipment put in or on your vehicle the weight of the driver and all passengers note: remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is", "weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids,", "Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.", "Installing The Rear Window And Quarter Panel Cover Assemblies If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: Guide the top of the quarter panel cover assembly up into the retainer.  Step one caution: failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the soft top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide the rear window into the retainer while keeping the window level.  Step four engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the", "window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step five engage the vertical retainers up the right and left side of the rear window.  Step six tuck the rear window under the soft top fabric and press firmly.  Step seven engage the rear window retainers in the lower right and left corners.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do", "level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be", "or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Installing The Rear Window And Quarter Panel Cover Assemblies If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: Guide the top of the quarter panel cover assembly up into the retainer.  Step one caution: failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the soft top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide the rear window into the retainer while keeping the window level.  Step four engage the", "side, guide the rear window into the retainer while keeping the window level.  Step four engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step five engage the vertical retainers up the right and left side of the rear window.  Step six tuck the rear window under the soft top fabric and press firmly.  Step seven engage the rear window retainers in the lower right and left corners.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  CAUTION: Manual Sliding Rear Window \u2014 If Equipped To open the rear sliding window, push the release button inward while sliding the window into the open position.  Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps", "And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom,", "on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Installing The Rear Window And Quarter Panel Cover Assemblies If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: Guide the top of the quarter panel cover assembly up into the retainer.  Step one caution: failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the soft top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the", "of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide the rear window into the retainer while keeping the window level.  Step four engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step five engage the vertical retainers up the right and left side of the rear window.  Step six tuck the rear window under the soft top fabric and press firmly.  Step seven engage the rear window retainers in the lower right and left corners.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or", "Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  CAUTION: Soft Top Rear Window Storage Bag \u2014 If Equipped To safely store the soft top rear window, proceed as follows: With the bag opened completely, fold the fabric divider downward and lay the rear window in the bottom of the bag.  Step one fold the divider upward, covering the rear window.  Step two lay the first quarter panel cover assembly all the way to the right side and the second quarter panel cover assembly on the left side.  Secure both using the two hook-and-loop fastener straps on each side.  Note: the quarter panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step three 1 \u2014 left quarter panel cover assembly 2 \u2014 right quarter panel cover assembly close the storage bag and store in a safe location.", "Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWRWARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do", "and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  On-Road Driving Tips Utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications.  Specific design characteristics give them a higher center of gravity than conventional passenger cars.  An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems.  They are not designed for cornering at the same speeds as conventional passenger cars any more than low-slung sports cars are designed to perform satisfactorily in off-road conditions.  Avoid sharp turns or abrupt maneuvers.  As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover.  Driving Across An Incline If", "vehicle correctly may result in loss of control or vehicle rollover.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying", "this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced", "a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly", "not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.", "System Malfunction If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  In following situations the engine will not stop: driver\u2019s seat belt is not buckled outside temperature is less than 10\u00b0f (\u201312\u00b0c) or greater than 109\u00b0f (43\u00b0c) actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode engine has not reached normal operating temperature battery is discharged when driving in reverse hood is open transfer case is in 4l or n (neutral) driver's seat is not occupied or driver door is open vehicle is at", "case is in 4l or n (neutral) driver's seat is not occupied or driver door is open vehicle is at high altitude the vehicle is on a steep grade forward gear is engaged steering angle is beyond threshold system fault is present hvac is set to max a/c it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has", "is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about", "check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system", "steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal", "to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  In following situations the engine will not stop: driver\u2019s seat belt is not buckled outside temperature is less than 10\u00b0f (\u201312\u00b0c) or greater than 109\u00b0f (43\u00b0c)", "seat belt is not buckled outside temperature is less than 10\u00b0f (\u201312\u00b0c) or greater than 109\u00b0f (43\u00b0c) actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode engine has not reached normal operating temperature battery is discharged when driving in reverse hood is open transfer case is in 4l or n (neutral) driver's seat is not occupied or driver door is open vehicle is at high altitude the vehicle is on a steep grade forward gear is engaged steering angle is beyond threshold system fault is present hvac is set to max a/c it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  To Start The Engine While In Autostop Mode When the gear selector is in NEUTRAL, the engine will start when the clutch pedal is pressed (does not require complete/full pedal press).  The vehicle will go into STOP/START SYSTEM NOT READY mode", "not require complete/full pedal press).  The vehicle will go into STOP/START SYSTEM NOT READY mode until the vehicle speed is greater than 5 mph (8 km/h).", "Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to", "of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Lock press this button to lock your vehicle.  Vehicle start press this button to start your vehicle.  Horn & lights press this button to sound the horn and activate your lights.  Unlock press this button to unlock your vehicle.  Cancel vehicle", "horn and activate your lights.  Unlock press this button to unlock your vehicle.  Cancel vehicle start press this button to cancel remote start.  Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.", "When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1", "Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided", "the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners Loosen the fasteners from the engine air cleaner filter cover using a suitable tool.  Engine Air Cleaner Filter Cover 1 \u2014 Fasteners 2 \u2014 Engine Air Cleaner Filter Cover Lift the engine air cleaner filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from the housing assembly.  engine air cleaner filter cover  Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For", "Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque Specification For Torx Fastener Maximum Minimum 119.5 in-lb (13.5", "torque specifications.  Torque Specification For Torx Fastener Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  Damage to the retainers will occur.  Step One Install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step Four Using the provided #T50 Torx head driver and ratchet, install and tighten the Torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the", "by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step Five Torque Specification For Torx Fasteners Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Step Five Before driving the vehicle with the top in the Sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners Step Six  Installing The Soft Top Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque specification for torx fastener maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.", "n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  Damage to the retainers will occur.  Step one 1 \u2014 corner fasteners 2 \u2014 rear fasteners install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Caution: failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step four using the provided #t50 torx head driver and ratchet, install and tighten the torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the", "until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step five torque specification for torx fasteners maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Step five before driving the vehicle with the top in the sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners.  Step Six Note:", "The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  Bed Rail Tie Down Locations Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.  The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction", "between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Supplemental Seat-Mounted Side Air Bags (SABs) are located in the outboard side of the front seats.  The SABs are marked with a \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d on a label or on the seat trim on the outboard side of the seats.  Four auxiliary switches are located in the lower switch bank of the instrument panel and can be used to power various electrical devices.  1 \u2014 Retainers 2 \u2014 Fuel Filter Protective Cover The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of", "secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should", "load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  Lower Anchors And Tethers For CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.  BED RAIL TIE DOWN SYSTEM \u2014 IF", "restraint.  Please see the following table for more information.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout", "the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.", "Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see \"\u21e8draining fuel/water separator filter \u2014 diesel engine\" .  Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential seeBulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.", "into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Fuel Oxidation Stability \u2014 Must Use Fuel Within Six Months Of Manufacture Biodiesel fuel has poor oxidation stability which can result in long term storage problems.  Fuel produced to approved ASTM standards, if stored properly, provides for protection against fuel oxidation for up to six months.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or", "Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent", "or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range", "Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively", "or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor", "than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  Do Not Operate The Engine With Failed Parts All engine failures give some warning before the parts fail.  Be on the alert for changes in performance, sounds, and visual evidence that the engine requires service.  Some important clues are: engine misfiring or vibrating severely sudden loss of power unusual engine noises fuel, oil or coolant leaks sudden change, outside the normal operating range, in the engine operating temperature excessive smoke oil pressure drop shifting fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is", "when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle", "missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and", "(MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily", "suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  For further information on GAWRs, vehicle loading, and trailer towing, see  The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the", "passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWRThe GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  For further information on GAWRs, vehicle loading, and trailer towing, see Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options", "GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.", "Feature description controls \u2014 if equipped press the controls button to access vehicle-specific features like heated seats and steering wheel.  Apps press the apps button to access a list of the available mobile apps.  Climate press the climate button to enter climate mode and access the climate control functions.  Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF.  Climate Control OFF Button Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.  Feature description controls \u2014 if equipped press the controls button to access vehicle-specific features like heated seats and steering wheel.  Apps press the apps button to access a list of the available mobile apps.  Climate press the climate button to enter climate mode and access the climate control functions \"\u21e8climate", "press the climate button to enter climate mode and access the climate control functions \"\u21e8climate controls\" .", "Conditions that will cause the engine to start automatically while in stop/start autostop active mode, the engine will start automatically when: actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode stop/start autostop active time exceeds five minutes battery voltage drops too low vehicle is moving faster than 5 mph (8 km/h) stop/start off switch is pressed transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold (ess models only) to start the engine while in autostop mode while in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is pressed.  The transmission will automatically re-engage upon engine restart.  Conditions that will cause the engine to start automatically while in autostop mode: the transmission selector is moved out of drive to maintain cabin temperature comfort actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to", "cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode hvac system temperature or fan speed is manually adjusted battery voltage drops too low stop/start off switch is pushed a stop/start system error occurs stop/start autostop active time exceeds five minutes transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold.  Conditions that will cause the engine to start automatically while in stop/start autostop active mode, the engine will start automatically when: actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode stop/start autostop active time exceeds five minutes battery voltage drops too low vehicle is moving faster than 5 mph (8 km/h) stop/start off switch is pressed transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold (ess models only).  To Start The Engine While In Autostop Mode While in a forward gear, the engine will start when the", "To Start The Engine While In Autostop Mode While in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is pressed.  The transmission will automatically re-engage upon engine restart.", "Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try", "the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions:", "familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in", "Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your", "dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely", "the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedureWARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these", "with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is", "If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.", "enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedureWARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The", "high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Priming If The", "\"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with", "agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.", "The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the", "is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below", "to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect", "Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  Installing The Soft Top Install the belt rail on the", "this caution could damage the hard top.  Installing The Soft Top Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque specification for torx fastener maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  Damage to the retainers will occur.  Step one 1 \u2014 corner fasteners 2 \u2014 rear fasteners install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Caution: failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto", "Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step four using the provided #t50 torx head driver and ratchet, install and tighten the torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step five torque specification for torx fasteners maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Step five before driving the vehicle with the top in the sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners.  Step Six Note:  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on", "Step Six Note:  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners", "protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.", "Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.  Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Three-Position Tailgate The", "tailgate is dampened to provide a slower, more controlled lowering.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to", "Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).", "Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an", "information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system", "personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL", "your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.", "Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The", "for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated", "store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a", "occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedureWARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in", "and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine", "the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products", "which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.", "Fuel Filler Cap The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Open the fuel filler door.  Fuel filler door remove the fuel cap by rotating it counterclockwise.  Fuel filler cap fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the", "is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light (MIL) to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  CAUTION: Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Note: When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure", "tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  After fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged.  If the system detects a malfunction, the \u201cgASCAP\u201d message will display in the odometer display.  Tighten the gas cap until a \"clicking\" sound is heard.  This is an indication that the gas cap is properly tightened.  Push the odometer reset button to turn the message off.  If the problem persists, the message will appear the next time the vehicle is started.  This might indicate a", "persists, the message will appear the next time the vehicle is started.  This might indicate a damaged cap.  If the problem is detected twice in a row, the system will turn on the MIL.  Resolving the problem will turn the MIL off.  The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal", "the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the", "belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure", "One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners Loosen the fasteners from the engine air cleaner filter cover using a suitable tool.  Engine Air Cleaner Filter Cover 1 \u2014 Fasteners 2 \u2014 Engine Air Cleaner Filter Cover Lift the engine air cleaner filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from the housing assembly.  engine air cleaner filter cover", "The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  Interior Courtesy Lights When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right)", "the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  To enter the \u201cPartial Off\u201d mode, momentarily push the ESC OFF button and the ESC OFF Indicator Light will illuminate.  To turn the ESC on again, momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door", "momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Automatic Headlight System will turn the headlights on or off according to ambient light levels.  To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation.  When the system is on, the headlight time delay feature is also on.  This means the headlights will stay on for up to 90 seconds (programmable through the uconnect settings \"\u21e8uconnect settings\" ) after you place the ignition into the off position.  To turn the automatic system off, move the headlight switch out of the AUTO position.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the", "The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Reduce power to unnecessary loads if possible: Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed", "settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s exterior and interior lights.  When the \u201cDaytime Running Lights\u201d feature is selected, the daytime running lights can be turned on or off.  This feature is only allowed by law in the country of the vehicle purchase.  Depending on the vehicle\u2019s options, feature settings may vary.  Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to", "lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other", "systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road", "lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5", "fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a", "Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to", "Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Door Frame Installation Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten fasteners target torque specification for torx fasteners maximum minimum 44.2 in-lb (5 n\u00b7m) 53.1 in-lb (6 n\u00b7m) 35.4 in-lb (4 n\u00b7m) caution: do", "torx fasteners maximum minimum 44.2 in-lb (5 n\u00b7m) 53.1 in-lb (6 n\u00b7m) 35.4 in-lb (4 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step five step five insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the", "each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.", "Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  From the Sunrider\u00ae Position, remove straps if previously secured.  Step One Failure to follow the next steps could result in damage to the soft top or vehicle.  Using the side link, lift and push the soft top toward the front of the vehicle, manually guiding the top into the closed position.  Step Two Step Two From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Step Three Pull the handle back upward while squeezing the hook, locking the latch into place.  Step Four It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and", "while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Soft Top Rear Window Storage Bag \u2014 If Equipped To safely store the soft top rear window, proceed as follows: With the bag opened completely, fold the fabric divider downward and lay the rear window in the bottom of the bag.  Step one fold the divider upward, covering the rear window.  Step two lay the first quarter panel cover assembly all the way to the right side and the second quarter panel cover assembly on the left side.  Secure both using the two hook-and-loop fastener straps on each side.  Note: the quarter panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step three 1 \u2014 left quarter panel cover assembly 2 \u2014 right quarter panel cover assembly", "assembly.  Step three 1 \u2014 left quarter panel cover assembly 2 \u2014 right quarter panel cover assembly close the storage bag and store in a safe location.  Installing The Rear Window And Quarter Panel Cover Assemblies If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: Guide the top of the quarter panel cover assembly up into the retainer.  Step one caution: failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the soft top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide the rear window into the retainer while keeping the window level.  Step four", "either side, guide the rear window into the retainer while keeping the window level.  Step four engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step five engage the vertical retainers up the right and left side of the rear window.  Step six tuck the rear window under the soft top fabric and press firmly.  Step seven engage the rear window retainers in the lower right and left corners.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.", "Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set", "the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.", "To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c.20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately", "your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov .  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the", "has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved", "is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not", "5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.", "Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  1 \u2014 Upper Console Storage Latch 2 \u2014 Lower Console Storage Latch To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock", "the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.", "The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is", "will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering", "not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel", "as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The engine must be running for the heated steering wheel to operate.", "When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route", "ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no", "to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  Mud Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get", "debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any", "The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These", "to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it", "for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the", "Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  The instrument cluster display features a driver interactive displayThe Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The instrument cluster display will show the current ACC system settings.  The Instrument Cluster Display is located in the center of the instrument cluster.  The information it displays depends on ACC system status.  Instrument Cluster Display Control Buttons The instrument cluster has an SSC icon and the SSC switch has a light that offers feedback to the driver about the state SSC is in.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside", "of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument", "the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  To close the tailgate, lift upward until both sides latch into place.  Opening To open the tailgate, pull the release handle located on the center of the tailgate", "place.  Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.", "Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with", "vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not", "you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced", "control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the", "The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could", "Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or", "for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10", "Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.", "Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug", "surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x", "socket.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.  WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.", "Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.", "the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This warning light will indicate when", "the heater/air conditioning (hvac) air flow will be reduced.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display If an obstacle is detected in the center front region, the display will show a", "cluster display If an obstacle is detected in the center front region, the display will show a single solid arc in the center front region with no chime.  As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and a fast sound tone will be heard and will change from fast, to continuous.  Instrument cluster descriptions tachometer indicates the engine speed in revolutions per minute (rpm x 1000).  Caution: do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature gauge the temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You", "limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Caution: driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument cluster display the instrument cluster display features a driver interactive display.  Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer indicates vehicle speed.  Speedometer push and release the up or down arrow button until", "indicates vehicle speed.  Speedometer push and release the up or down arrow button until the speedometer menu icon is displayed in the instrument cluster display.  Push and release the ok button to toggle between mph and km/h.  Favorite menus speedometer vehicle info off road \u2014 if equipped (show/hide) driver assist \u2014 if equipped (show/hide) fuel economy (show/hide) trip info (show/hide) stop / start \u2014 if equipped audio (show/hide) messages screen setup vehicle settings \u2014 if equipped.  Instrument cluster descriptions tachometer indicates the engine speed in revolutions per minute (rpm x 1000).  Caution: do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature gauge the temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a", "indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Caution: driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument cluster display the instrument cluster display features a driver interactive display.  Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of", "when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer indicates vehicle speed.", "Engine Oil Filter Selection A full-flow type disposable oil filter should be used for replacement.  The quality of replacement filter varies considerably.  We recommend using a Mopar\u00ae engine oil filter, if a Mopar\u00ae engine oil filter is unavailable only use filters that meet or exceed SAE/USCAR-36 Filter performance requirements.  Engine Oil Filter Replacement Residual oil in the housing may spill from the housing when the new filter is installed if the residual oil is not either removed from the housing or enough time has not elapsed to allow the oil to drain back into the engine.  When servicing the oil filter on this engine, open the filter cap approximately six turns until the cap o-ring is visible and stop.  Wait five minutes with the cap in this position to allow dirty engine oil to drain back into the engine.  After five minutes, the cap and filter assembly can be removed and discarded.  Engine Oil Filter The engine oil filter should be replaced with a new filter at every engine oil change.  Engine Oil", "The engine oil filter should be replaced with a new filter at every engine oil change.  Engine Oil Filter Selection A full-flow type disposable oil filter should be used for replacement.  The quality of replacement filter varies considerably.  We recommend using a Mopar\u00ae engine oil filter, if a Mopar\u00ae engine oil filter is unavailable only use filters that meet or exceed SAE/USCAR-36 Filter performance requirements.  Inspect engine air cleaner filter if using in dusty or off-road conditions, replace engine air cleaner filter if necessary.  The engine oil filter should be replaced with a new filter at every engine oil change.  A full-flow type disposable oil filter should be used for replacement.  The quality of replacement filter varies considerably.  We recommend using a Mopar\u00ae engine oil filter, if a Mopar\u00ae engine oil filter is unavailable only use filters that meet or exceed SAE/USCAR-36 Filter performance requirements.  Engine Oil Filter Replacement", "Automatic High Beam Headlamp Control \u2014 If Equipped The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automatically controlling the high beams through the use of a camera mounted on the vehicle\u2019s header.  This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.  Note: the automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.  This mirror automatically adjusts for headlight glare", "cause the system to function improperly.  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.  High/Low Beam Switch The High/Low Beam switch is located within the multifunction lever on", "High/Low Beam Switch The High/Low Beam switch is located within the multifunction lever on the left side of the steering wheel.  High beam headlights can be used for improved visibility in low lit areas when there is no oncoming traffic.  Otherwise, it is recommended to use the low beam headlights to reduce glare to other vehicles.  With the headlight switch activated, push the multifunction lever toward the instrument panel to switch the headlights to high beams.  The lever will return to the centered position.  To return the headlights to low beam, pull the lever toward the steering wheel, or push the lever toward the instrument panel.", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check", "to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following", "If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the", "take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for", "main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Lockout Service Whether the keys are locked in your vehicle or frozen locks are keeping you from getting on your way, help is just a phone call away.  This service is limited to providing access to the vehicle\u2019s seating area.  It does not cover the cost of replacement keys.  VEHICLE MAINTENANCE An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions control systems", "attempting any procedure yourself.  Note: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  WARNING: You can be badly injured working on or around a motor vehicle.  Only do service work for which you have the knowledge and the proper equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.", "Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts", "Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners", "careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it", "bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx", "arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Bumper end caps are removable on steel bumpers only.  The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket", "bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 Bolt #2 Remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step Two 1 \u2014 Hex Bolt Cover Installed 2 \u2014 Hex Bolt Cover Removed Using the provided 15 mm socket, remove the two hex bolts and remove", "2 \u2014 Hex Bolt Cover Removed Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step Six Secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Do Not Overtighten!  Damage to the windshield could result.  Open the fuel filler door.  Fuel Filler Door Remove the fuel cap by rotating it counterclockwise.  Fuel Filler Cap Fully insert the", "Filler Door Remove the fuel cap by rotating it counterclockwise.  Fuel Filler Cap Fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.", "Driving Through Water Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher", "the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  CAUTION: Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  Before You Cross Any Type Of Water As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth,", "get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Crossing Puddles, Pools, Flooded Areas Or Other Standing Water Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle", "want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.  CAUTION: Muddy waters can reduce the cooling system effectiveness by depositing debris onto the radiator.  Crossing Puddles, Pools, Flooded Areas Or Other Standing Water Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.  CAUTION: Muddy waters can reduce the cooling system effectiveness by depositing debris onto the radiator.  Driving Through Water Extreme care should be", "effectiveness by depositing debris onto the radiator.  Driving Through Water Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate", "5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  CAUTION: Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water Flowing water can be extremely dangerous.  Never attempt to cross a fast running stream or river even in shallow water.  Fast", "dangerous.  Never attempt to cross a fast running stream or river even in shallow water.  Fast moving water can easily push your vehicle downstream, sweeping it out of control.  Even in very shallow water, a high current can still wash the dirt out from around your tires putting you and your vehicle in jeopardy.  There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the vehicle's running ground clearance.  You should never attempt to cross flowing water which is deeper than the vehicle's running ground clearance.  Even the slowest current can push the heaviest vehicle downstream and out of control if the water is deep enough to push on the large surface area of the vehicle's body.  Before you proceed, determine the speed of the current, the water's depth, approach angle, bottom condition and if there are any obstacles.  Then cross at an angle heading slightly upstream using the low and slow technique.  WARNING: Never drive through fast moving deep", "slightly upstream using the low and slow technique.  WARNING: Never drive through fast moving deep water.  It can push your vehicle downstream, sweeping it out of control.  This could put you and your passengers at risk of injury or drowning.  Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L", "gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  As you approach any type of water, you", "may not be covered by the New Vehicle Limited Warranty.  As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are", "an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.", "To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped)Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security", "Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.", "system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for", "the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF", "Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY", "system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be", "may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  Connected Services Send & Go FAQs \u2014 If Equipped How long does it take to send the route and destination to my vehicle?  Depending on various conditions, it can take up to three minutes for the request to get through to your vehicle.  Can I cancel a route I sent to my vehicle?  Yes, once you enter your vehicle, and start the engine, the pop-up message stating that you have a new route will appear.  There is an exit button on the pop-up that will cancel the route if selected.  Can I select a different route than the most recent one I sent to my vehicle?  Yes, once you enter the vehicle, and start the engine, the pop-up message offers a \u201cLocations\u201d option.  Once \u201cLocations\u201d is selected, you can choose from a list of recently sent destinations.  Power-Up After switching the ignition key from OFF to either the ON/RUN or ACC position, or", "Power-Up After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil", "occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy", "significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Introduction To Connected Vehicle Services One of the many benefits of your vehicle\u2019s Uconnect system is that you can now take advantage of SiriusXM Guardian\u2122 connected services.  To unlock the full potential of SiriusXM Guardian\u2122 in your vehicle, you first need to activate SiriusXM Guardian\u2122 connected services.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.", "Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Note: SiriusXM Guardian\u2122 involves the collection, transmission and use of data from your vehicle  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.", "oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.", "This is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer.  They want to know if you need assistance.  If an authorized dealer is unable to resolve the concern, you may contact FCA US LLC's Customer Assistance center.  FCA US LLC and its authorized dealers are vitally interested in your satisfaction.  We want you to be happy with our products and services.  Warranty service must be done by an authorized dealer.  We strongly recommend that you take the vehicle to an authorized dealer.  They know your vehicle the best, and are most concerned that you get prompt and high quality service.  FCA US LLC's authorized dealers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner.  This is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason", "is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer.  They want to know if you need assistance.  If an authorized dealer is unable to resolve the concern, you may contact FCA US LLC's Customer Assistance center.  We recommend seeing an authorized dealer for service.  An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  If the transmission cannot be reset, authorized dealer service is required.  Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us)", "with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada) symbols key if you do not read the entire owner\u2019s manual, you may miss important information.  Observe all Cautions and Warnings.  Service Manuals These comprehensive Service Manuals provide a complete working knowledge of the vehicle, system, and/or components and is written in straightforward language with illustrations, diagrams, and charts.", "Adaptive Cruise Control (ACC)/Forward Collision Warning (FCW) Sensor Protective Cover \u2014 If Equipped Your vehicle may be equipped with a protective cover that is to be used whenever the windshield is folded down in order to protect the ACC/FCW sensor.  To install the cover, refer to the following instructions: Secure the top part of the cover so that it hinges to the header.  Swing the cover down and push on it so that it covers the opening.  Check to make sure the cover is secured properly.  Note: Be sure to remove the cover before returning the windshield to the normal position.  Store the cover in the cargo area.  Your vehicle may be equipped with a protective cover that is to be used whenever the windshield is folded down in order to protect the ACC/FCW sensor.  To install the cover, refer to the following instructions: If the \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the radar sensor", "than once on every trip) without any snow, rain, mud, or other obstruction, have the radar sensor realigned at an authorized dealer.  The \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d warning will display and a chime will sound when conditions temporarily limit system performance.  Always keep the sensor clean.  Carefully wipe the sensor lens with a soft cloth.  Be cautious not to damage the sensor lens.  Do not remove any screws from the sensor.  Doing so could cause an ACC system malfunction or failure and require a sensor realignment.  If the sensor or front end of the vehicle is damaged due to a collision, see an authorized dealer for service.  Do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles.  Doing so could cause an ACC system failure or malfunction.  If the \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d warning is active, Fixed Speed Cruise Control is still available.  The \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d warning will", "is still available.  The \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d warning will display and a chime will sound when conditions temporarily limit system performance.  This most often occurs at times of poor visibility, such as in snow or heavy rain and fog.  The ACC system may also become temporarily blinded due to obstructions, such as mud, dirt, or ice on windshield and fog on the inside of glass.  In these cases, the instrument cluster display will read \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d and the system will have degraded performance.  If the instrument cluster displays \u201cACC/FCW Limited Functionality\u201d or \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d momentarily, there may be a condition that limits FCW functionality.  Although the vehicle is still drivable under normal conditions, the active braking may not be fully available.  Once the condition that limited the system performance is no longer present, the system will return to its full performance state.  If the", "performance is no longer present, the system will return to its full performance state.  If the problem persists, see an authorized dealer.  If the system turns off, and the instrument cluster display reads \u201cACC/FCW Unavailable Service Required\u201d or \u201cCruise/FCW Unavailable Service Required\u201d, there may be an internal system fault or a temporary malfunction that limits ACC functionality.  Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.  If this occurs, try activating ACC again later, following an ignition cycle.  If the problem persists, see an authorized dealer.  This message can sometimes be displayed while driving in adverse weather conditions.  The ACC/FCW system will recover after the vehicle has left these areas.  Under rare conditions, when the camera is not tracking any vehicles or objects in its path this warning may temporarily occur.  Changing the FCW status to \u201cOnly Warning\u201d prevents the system from providing limited active braking, or additional", "status to \u201cOnly Warning\u201d prevents the system from providing limited active braking, or additional brake support if the driver is not braking adequately in the event of a potential frontal collision, but maintains the audible and visual warnings.  Changing the FCW status to \u201cOff\u201d prevents the system from providing autonomous braking, or additional brake support if the driver is not braking adequately in the event of a potential frontal collision.  The system will retain the last setting selected by the driver after ignition shut down.  FCW may not react to irrelevant objects such as overhead objects, ground reflections, objects not in the path of the vehicle, stationary objects that are far away, oncoming traffic, or leading vehicles with the same or higher rates of speed.  FCW will be disabled like ACC, with the unavailable screens.  Service ACC/FCW Warning If the system turns off, and the instrument cluster display reads \u201cACC/FCW Unavailable Service Required\u201d or \u201cCruise/FCW Unavailable Service Required\u201d,", "display reads \u201cACC/FCW Unavailable Service Required\u201d or \u201cCruise/FCW Unavailable Service Required\u201d, there may be an internal system fault or a temporary malfunction that limits ACC functionality.  Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.  If this occurs, try activating ACC again later, following an ignition cycle.  If the problem persists, see an authorized dealer.", "To Start The Engine While In Autostop Mode While in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is pressed.  The transmission will automatically re-engage upon engine restart.  To Activate The Autostop Mode, The Following Must Occur: Conditions That Will Cause The Engine To Start Automatically While In Autostop Mode: To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: Conditions that will cause the engine to start automatically while in STOP/START AUTOSTOP ACTIVE mode, the engine will start automatically when: This indicator light will illuminate when the Stop/Start function is in \u201cAutostop\u201d mode.  The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  While in an Autostop,", "other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  While in an Autostop, the Climate Control system may automatically adjust airflow to maintain cabin comfort.  Customer settings will be maintained upon return to an engine running condition.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This light alerts the driver that the vehicle is in the neutral mode  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and", "speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air", "to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  If you get hung up or high-centered on an object,", "jacking on locations other than those indicated.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.", "get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand,", "brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change", "changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.", "The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or", "large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  External racks do not increase the total load carrying capacity of the vehicle.  Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, does not exceed the maximum vehicle load capacity.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  The Roof Luggage Rack is designed to allow for carrying an", "sport bar, and body, or fully removed.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight", "roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.", "Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on", "may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Seat Belt Reminder Warning Light This warning light indicates when the driver or passenger seat belt is unbuckled.  When the ignition is first placed in the ON/RUN or ACC/ON/RUN position and if the driver\u2019s seat belt is unbuckled, a chime will sound and the light will turn on.  When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound Service 4WD Warning Light \u2014 If Equipped This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning", "If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.", "The BSM system notifies the driver of objects in the detection zones by illuminating the BSM Warning Light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume.  See \"\u21e8blind spot modes\" for further information.  The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.  The BSM system will issue an alert during these types of zone entries.  When the BSM system is turned off there will be no visual or audible alerts from either the BSM or RCP systems.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft", "12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft (3 m) beyond the rear fascia/bumper of the vehicle.  The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas.  BSM Radar Location (Left Side Shown) The BSM system will store the current operating mode when the vehicle is shut off.  Each time the vehicle is started the previously stored mode will be recalled and used.  Blind Spot Monitoring (BSM) \u2014 If Equipped The BSM system uses two radar sensors, located inside the taillights, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.)  that enter the blind spot zones from the rear/front/side of the vehicle.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate", "mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft (3 m) beyond the rear fascia/bumper of the vehicle.  The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas.  The BSM system can become blocked if snow, ice, mud, or other road contaminations accumulate on the rear fascia/bumper where the radar sensors are located.  The system may also detect a blockage if the vehicle is operated in areas with extremely low radar returns, such as a desert, or parallel to a large elevation drop.  If a blockage is detected, a \u201cBlind Spot Temporarily Unavailable, Wipe Rear Corners\u201d message will display in the instrument", "a \u201cBlind Spot Temporarily Unavailable, Wipe Rear Corners\u201d message will display in the instrument cluster, both mirror lights will illuminate, and BSM and RCP alerts will be disabled.  This is normal operation.  The system will automatically resume function when the condition clears.  To minimize system blockage, do not block the area of the rear fascia/bumper where the radar sensors are located with foreign objects (bumper stickers, bicycle racks, etc.)  and keep it clear of road contaminations.  The BSM system notifies the driver of objects in the detection zones by illuminating the BSM Warning Light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume.  See \"\u21e8blind spot modes\" for further information.  The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.  The BSM system will issue an alert during these types of zone entries.  Note: The BSM system DOES NOT alert", "system will issue an alert during these types of zone entries.  Note: The BSM system DOES NOT alert the driver about rapidly approaching vehicles that are outside the detection zones.  The BSM system detection zone DOES NOT change if your vehicle is towing a trailer.  Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change.  If the trailer or other object (i.e., bicycle, sports equipment) extends beyond the side of your vehicle, this may result in the BSM Warning Light remaining illuminated the entire time the vehicle is in a forward gear.  See \"\u21e8uconnect settings\" for more information.  The Blind Spot Monitoring (BSM) system may experience dropouts (blinking on and off) of the side mirror warning indicator lights when a motorcycle or any small object remains at the side of the vehicle for extended periods of time (more than a couple of seconds).  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center", "rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  Manual Mirror Adjustment If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror", "small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Ignoring the Rearview Mirror light could mean you will not have SOS Call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  When cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on", "mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on the mirror.", "Brake/Transmission Shift Interlock (BTSI) System This vehicle is equipped with a BTSI system that holds the transmission gear selector in PARK unless the brakes are applied.  To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.  The brake pedal must also be pressed to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is stopped or moving at low speeds.  Brake/Transmission Shift Interlock (BTSI) System This vehicle is equipped with a BTSI system that holds the transmission gear selector in PARK unless the brakes are applied.  To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.  The brake pedal must also be pressed to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is stopped or moving at low speeds.  Ignition Park Interlock This vehicle is equipped with an Ignition Park Interlock system which requires the transmission to be in PARK before the ignition can be turned to the OFF position.  This", "the transmission to be in PARK before the ignition can be turned to the OFF position.  This helps the driver avoid inadvertently leaving the vehicle without placing the transmission in PARK.  This system also locks the transmission in PARK whenever the ignition is in the OFF position.  Note: The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  AUTOMATIC TRANSMISSION \u2014 IF EQUIPPED You must press and hold the brake pedal while shifting out of PARK.  WARNING: Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure", "trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a", "a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or", "the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  CAUTION: Shift into or out of PARK or REVERSE only after the vehicle has come to a complete stop.  Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed.  Before shifting into any gear, make sure your foot is firmly pressing the brake pedal.  ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the", "cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Ignition Park Interlock This vehicle is equipped with an Ignition Park Interlock system which requires the transmission to be in PARK before the ignition can be turned to the OFF position.  This helps the driver avoid inadvertently leaving the vehicle without placing the transmission in PARK.  This system also locks the transmission in PARK whenever the ignition is in the OFF position.  Note: The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  Power-Up After switching the ignition key from OFF to either the ON/RUN or ACC position, or", "Power-Up After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press", "Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the", "km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam", "in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD", "Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button", "is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an", "SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.", "To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when", "20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set", "ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speed  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed", "show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which", "sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.", "Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect", "against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.", "vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Place the vehicle in a warm area.  Pull steadily on the top", "to leak into the vehicle's interior.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  From the Sunrider\u00ae Position, remove straps if previously secured.  Step One Failure to follow the next steps could result in damage to the soft top or vehicle.  Using the side link, lift and push the soft top toward the front of the vehicle, manually guiding the top into the closed position.  Step Two Step Two From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Step Three Pull the handle back upward while squeezing the hook, locking the latch into place.  Step Four It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's", "opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING:", "(5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional", "not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric topDo not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet", "prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Preparations For Jacking Park on a firm, level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking", "operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers should not remain in the vehicle when the vehicle is being jacked in position.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating", "not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.", "Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a", "6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition", "voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both", "it to work with Android Auto\u2122.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 \u00b9 use this qr code to access your digital experience.  While using Android Auto\u2122, Google Maps\u2122 provides voice-guided:  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.", "new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.", "cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  While using Android Auto\u2122, Google Maps\u2122 provides voice-guided: Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data", "on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Plugging in a smartphone device", "devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE", "USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into", "the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.", "Window Lockout Switch The window lockout switch allows you to disable the window controls on the rear passenger doors.  To disable the window controls, rotate the switch downward.  To enable the window controls, rotate the switch upward.  Child-Protection Door Lock System \u2014 Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove the sealing plug for access, and use a flat-blade screwdriver (or mechanical key) to rotate the dial to the lock or unlock position.  Note: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test", "it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Note: Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  Auto-Down Feature The driver door power window switch and the front passenger door power window", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.", "In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  In some localities, it", "diesel emissions standards required by the Environmental Protection Agency.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the", "driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  This vehicle is equipped with a Diesel Exhaust Fluid (DEF) injection system and a Selective Catalytic Reduction (SCR) catalyst to meet the emission requirements.  Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the", "container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light (MIL) to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these", "monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you", "test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd", "you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.", "Vehicle Identification Number Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.  Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of", "A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.  To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  You have 30 seconds in which to initiate rolling code final step 2, after completing rolling code final step 1.", "If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire", "will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Using the provided #T40 Torx head driver and", "fasteners.  Damage to the vehicle\u2019s parts will occur.  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque Specification For Torx Fastener Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  Damage to the retainers will occur.  Step One Install the door frames.  Start with", "Torx fasteners.  Damage to the retainers will occur.  Step One Install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step Four Using the provided #T50 Torx head driver and ratchet, install and tighten the Torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step Five Torque Specification For Torx", "torque specifications.  Repeat on the opposite side.  Step Five Torque Specification For Torx Fasteners Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Step Five Before driving the vehicle with the top in the Sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners Step Six  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the", "and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "The ACC screen may display once again if any ACC activity occurs, which may include any of the following: This feature will only activate when the following conditions are met: The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: Once SSC is enabled it will activate automatically once the following conditions are met: The following conditions must be met in order for HSA to activate:  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: If the ABS Warning", "also may experience the following normal characteristics when the ABS activates: If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN", "If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To", "by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervalsYour vehicle is equipped with dual hydraulic brake systems.  If either of the two hydraulic systems lose normal capability, the remaining system will still function.  However, there will be some loss of overall braking effectiveness.  You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.  If the driver does not take action based upon these progressive warnings, then the system will provide a limited level", "not take action based upon these progressive warnings, then the system will provide a limited level of active braking to help slow the vehicle and mitigate the potential forward collision.  If the driver reacts to the warnings by braking and the system determines that the driver intends to avoid the collision by braking but has not applied sufficient brake force, the system will compensate and provide additional brake force as required.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).", "you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user's safety or the safety of others.  Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure", "vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The ACC system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.", "To ensure proper engine lubrication, the engine oil must be maintained at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Check engine oil level Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage Check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed Check function of all interior and exterior lights  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal", "(IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel", "or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Checking Oil Level To ensure proper engine lubrication, the engine oil must be maintained at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off.  Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.  There are four possible dipstick types: Crosshatched zone.  Crosshatched zone marked SAFE.  Crosshatched zone marked with MIN at the low end of the range and MAX at the high end of the range.  Crosshatched zone marked with dimples at the MIN and the MAX ends of the range.  Adding 1 qt (1 L) of oil when the reading is at the low end of the dipstick range will raise the oil level to the high end of the range marking.  Note: Always maintain the oil level within the crosshatch", "to the high end of the range marking.  Note: Always maintain the oil level within the crosshatch markings on the dipstick.  CAUTION: Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure.  This could damage your engine.  Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not", "as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.", "STOP/START SYSTEM \u2014 AUTOMATIC TRANSMISSION (IF EQUIPPED) The Engine Stop/Start (ESS) function is developed to reduce fuel consumption.  The system will stop the engine automatically during a vehicle stop if the required conditions are met.  Releasing the brake pedal or pressing the accelerator pedal will automatically restart the engine.  ESS vehicles have been upgraded with a heavy-duty starter, enhanced battery, and other upgraded engine parts, to handle the additional engine starts.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  STOP/START SYSTEM \u2014 MANUAL TRANSMISSION (IF EQUIPPED) The Engine Stop/Start (ESS) function is developed to reduce fuel consumption.  The system will stop the engine automatically during a vehicle stop if the required conditions are met.  Pressing the clutch pedal will automatically restart the vehicle.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  Electronic Stability Control (ESC) Active Warning Light", "system be disabled during off-road use.  Electronic Stability Control (ESC) Active Warning Light \u2014 If Equipped This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the", "The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.", "FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your", "in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you", "That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning:", "holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Natural Speech Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Natural speech allows the user to speak commands in phrases or complete sentences.  The system filters out certain non-word utterances and sounds such as \u201cah\u201d and \u201ceh.\u201d The system handles fill-in words such as \u201cI would like to\u201d.  The system handles multiple inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you", "identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you want to call?\u201d in the case where a phone call was requested but the specific name was not recognized.  The system utilizes continuous dialog.  When the system requires more information from the user, it will ask a question to which the user can respond without pushing the Voice Command button on the steering wheel.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two", "its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few", "works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly", "noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general", "structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: The following basic Voice Commands can be given at any point while using your Uconnect system.  Uconnect Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  Uconnect Phone is a voice-activated, hands-free, in-vehicle communications system.  It allows you to dial a phone number with your mobile phone.  Uconnect Phone will automatically connect to the highest priority paired phone and/or Audio Device within range.  If you need to choose a particular phone or audio device follow these steps: uconnect can announce incoming text messages.  Push the vr button or phone button and say: the phone feature is driven through your bluetooth\u00ae \u201chands-free profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables", "profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.", "Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  Engine start-up in very low ambient temperature", "time.  Wait 10 to 15 seconds before trying again.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant", "a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.", "To Turn On The Engine Using The ENGINE START/STOP Button The transmission must be in PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage automatically after 10 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for serviceIn unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should", "engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined", "Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to", "cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: The message will stay active until the ignition is placed in the ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to", "(instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  To insert an Auxiliary device, gently insert the Auxiliary device cable into the AUX port.  If you insert an Auxiliary device with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system will automatically time out", "on, the unit will switch to AUX Mode and begin to play.  The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.", "Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  Manual Mirror Adjustment If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an", "located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Ignoring the Rearview Mirror light could mean you will not have SOS Call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer", "of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  When cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on the mirror.  Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.  Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.  Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror.  The Outside Mirrors are located on the front driver and passenger side doors, and are adjusted manually or by power adjustment (if", "on the front driver and passenger side doors, and are adjusted manually or by power adjustment (if equipped).  If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.", "VEHICLE IDENTIFICATION NUMBER (VIN) The VIN is found on the left front corner of the A-pillar, visible from outside of the vehicle through the windshield.  Note: It is illegal to remove or alter the VIN plate.  Vehicle Identification Number Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.  Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle", "driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.", "BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load", "cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails,", "in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  Lower Anchors And Tethers For CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are", "seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in", "slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.", "It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is", "may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a", "to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or", "or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201dWARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including", "if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.", "come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with", "in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Potential signs of vehicle overheating: Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs,", "operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine", "brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear", "until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions:", "and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the", "with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Brake System Warning Light The red Brake System Warning Light", "Flashers may wear down your battery.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.", "Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When", "if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The", "of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the", "up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax", "etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak", "Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "Off-Road Driving Tips  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels,", "in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover", "is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good", "no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over", "ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur", "including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.", "Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune", "gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  Methylcyclopentadienyl Manganese Tricarbonyl (MMT) In Gasoline MMT is a manganese-containing metallic additive that is blended into some", "(MMT) In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasolines to increase octane.  Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT.  Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles.  The manufacturer recommends that gasoline without MMT be used in your vehicle.  The MMT content of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gasoline retailer whether the gasoline contains MMT.  MMT is prohibited in Federal law and California reformulated gasoline.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing", "and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system", "Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains", "of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.", "Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special", "paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you", "holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high", "have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.  Protection From", "by these type of products may not be covered by your New Vehicle Limited Warranty.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.", "ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are", "in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:  ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  To Turn Off", "to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC positionIf the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF", "pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.", "For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM", "reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost", "engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.", "Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids", "Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with", "for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine", "requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a", "conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3", "Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of", "(DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  Open the fuel filler door.  Fuel Filler Door Remove the diesel fuel filler cap by rotating it counterclockwise.  Fuel and Diesel Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the vehicle with fuel.  When the nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel filler door.", "Drivetrain The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  The following information is displayed: steering angle in degrees status of transfer case status of front axles \u2014 if equipped status of the rear axles \u2014 if equipped front and rear axle lock indicator light \u2014 if equipped this light indicates when the front, rear, or both axles have been locked.  The telltale will display the lock icon on the front and rear axles to indicate the current lock status.  Drivetrain Front Wheel Angle: displays the graphical and numerical value of calculated average front wheel angle from the steering wheel orientation.  Transfer Case Lock Status: displays \u201cLock\u201d graphic only during 4WD High, 4WD Auto, or 4WD Low status.  Axle Lock And Sway Bar Status (if equipped): displays front and rear or rear only axle locker graphic, and sway bar connection graphic with text message (connected or disconnected).  Drivetrain The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  The", "Drivetrain The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  The following information is displayed: steering angle in degrees status of transfer case status of front axles \u2014 if equipped status of the rear axles \u2014 if equipped drivetrain front wheel angle: displays the graphical and numerical value of calculated average front wheel angle from the steering wheel orientation.  Transfer Case Lock Status: displays \u201cLock\u201d graphic only during 4WD High, 4WD Auto, or 4WD Low status.  Axle Lock And Sway Bar Status (if equipped): displays front and rear or rear only axle locker graphic, and sway bar connection graphic with text message (connected or disconnected).  Steering angle in degrees Status of Transfer Case Status of Front Axles \u2014 If Equipped Status of the Rear Axles \u2014 If Equipped 1 \u2014 Steering Angle 2 \u2014 Lock Icon 3 \u2014 Sway Bar 4 \u2014 Front Axle Locker Status 5 \u2014 Rear Axle Locker Status This light indicates when the front, rear, or both axles have been locked.  The telltale will display", "light indicates when the front, rear, or both axles have been locked.  The telltale will display the lock icon on the front and rear axles to indicate the current lock status.", "US/CANADA Exposure to Radio Frequency Radiation The radiated output power of the internal wireless radio is far below the FCC and IC radio frequency exposure limits.  Nevertheless, the wireless radio will be used in such a manner that the radio is 8 inches (20 cm) or further from the human body.  The internal wireless radio operates within guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community.  The radio manufacturer believes the internal wireless radio is safe for use by consumers.  The level of energy emitted is far less than the electromagnetic energy emitted by wireless devices such as mobile phones.  However, the use of wireless radios may be restricted in some situations or environments, such as aboard airplanes.  If you are unsure of restrictions, you are encouraged to ask for authorization before turning on the wireless radio \"\u21e8general information\" .  Rolling Code Devices To determine if your device has a rolling code, a good", "information\" .  Rolling Code Devices To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Note: The \u201cLEARN\u201d or \u201cTRAIN\u201d button is not the button you normally use to operate the device.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with", "Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners", "features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a", "for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob", "systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.  Stationary Objects And Vehicles ACC does not react to stationary objects or vehicles.  For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane.  It will consider this stopped vehicle a stationary object as it did not previously detect movement from it.  Always be attentive and ready to apply the brakes if necessary.  Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.", "There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Prior to off-road usage, the side steps should be removed to prevent damage.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in", "Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  There are", "assemblies in the soft top rear window storage bag (if equipped), or a safe location.  There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  To reinstall the door(s), perform the previous steps in the reverse order.  Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is", "for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  Prior to off-road usage, the side steps should be removed to prevent damage.  Side Step Removal \u2014 If Equipped There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener locations (one side) remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road", "to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side steps should be removed to prevent damage.", "Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15,", "r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure", "load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire full size spare \u2014 if equipped the full size spare is for temporary emergency use only.  This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not.  This spare tire may have limited tread life.  When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced.  Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity.  Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and", "Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.", "The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Locking Storage Bin (Closed View) Locking Storage Bin  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be", "bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  Locking Storage Bin  Rear Wall Storage Bin The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  If equipped, the Locking Storage Bin is located below the rear", "fastener bin below the rear seat.  If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.", "Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the", "experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Fully lower the soft top to the Sunrider\u00ae positionFailure to follow the next steps could result in damage to the soft top or vehicle.  Using the provided #T50 Torx head driver and ratchet, unscrew the two Torx head fasteners on the inside of each top mechanism.  Step Two Utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle\u2019s sport bar and trim.  Store the soft top in a safe, clean, and dry location.  Remove the door frames.  The rear door frames must be removed before the front door framesUsing the provided #T50 Torx head driver and ratchet, unscrew the six Torx head fasteners on both rear corners and the back of the cab, then", "and ratchet, unscrew the six Torx head fasteners on both rear corners and the back of the cab, then remove the belt rail.  Folding down the rear seats is recommended to provide easier access to the fasteners.  Step Five 1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top", "cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.", "To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note:", "(NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Note: depending on the vehicle\u2019s options, feature settings may vary.  Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and", "Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the", "ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC positionIf the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will", "the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will", "transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If", "if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.", "may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or", "will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the", "when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the", "with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It", "a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel", "is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d,", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the", "driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will", "Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering", "pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the", "and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow", "Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.  The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window", "switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  Power Window Switches Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to", "for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as", "the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is", "up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "Draining Fuel/Water Separator Filter \u2014 Diesel Engine The fuel/water separator housing is located inside the left frame rail in front of the fuel tank.  The best access to this water drain valve is from under the vehicle.  If necessary remove the fuel filter protective cover to access the water drain valve.  If water is detected in the water separator while the engine is running, or while the ignition switch is in the ON position, the Water In Fuel Indicator Light will illuminate and an audible chime will be heard.  At this point you should stop the engine and drain the water from the filter housing.  Within 10 minutes of vehicle shutdown, turn the filter drain valve (located on the bottom of the filter housing) counterclockwise to drain fuel/water; allow the accumulated water to drain.  Leave the drain valve open until all water and contaminants have been removed.  When clear fuel is visible, close the drain valve by turning it clockwise.  Upon proper draining of the water from fuel filter assembly, the", "valve by turning it clockwise.  Upon proper draining of the water from fuel filter assembly, the Water In Fuel Indicator Light will remain illuminated for approximately 10 seconds.  If the water was drained while the engine was running, the Water In Fuel Indicator Light may remain on for approximately three minutes.  If more than two ounces or 60 ml of fuel have been drained, follow the directions for Priming If The Engine Has Run Out Of Fuel CAUTION: Do not drain the fuel/water separator filter when the engine is running.  Diesel fuel will damage blacktop paving surfaces.  Drain the filter into an appropriate container.  Note: Care should be taken in disposing of used fluids from your vehicle.  Used fluids, indiscriminately discarded, can present a problem to the environment.  Contact an authorized dealer, service station, or government agency for advice on recycling programs and for where used fluids and filters can be properly disposed of in your area.  Draining Fuel/Water Separator Filter \u2014 Diesel Engine", "can be properly disposed of in your area.  Draining Fuel/Water Separator Filter \u2014 Diesel Engine The fuel/water separator housing is located inside the left frame rail in front of the fuel tank.  The best access to this water drain valve is from under the vehicle.  If necessary remove the fuel filter protective cover to access the water drain valve.  If water is detected in the water separator while the engine is running, or while the ignition switch is in the ON position, the Water In Fuel Indicator Light will illuminate and an audible chime will be heard.  At this point you should stop the engine and drain the water from the filter housing.  Within 10 minutes of vehicle shutdown, turn the filter drain valve (located on the bottom of the filter housing) counterclockwise to drain fuel/water; allow the accumulated water to drain.  Leave the drain valve open until all water and contaminants have been removed.  When clear fuel is visible, close the drain valve by turning it clockwise.  Upon proper draining of", "When clear fuel is visible, close the drain valve by turning it clockwise.  Upon proper draining of the water from fuel filter assembly, the Water In Fuel Indicator Light will remain illuminated for approximately 10 seconds.  If the water was drained while the engine was running, the Water In Fuel Indicator Light may remain on for approximately three minutes.  If more than two ounces or 60 ml of fuel have been drained, follow the directions for Priming If The Engine Has Run Out Of Fuel CAUTION: Do not drain the fuel/water separator filter when the engine is running.  Diesel fuel will damage blacktop paving surfaces.  Drain the filter into an appropriate container.  Note: Care should be taken in disposing of used fluids from your vehicle.  Used fluids, indiscriminately discarded, can present a problem to the environment.  Contact an authorized dealer, service station, or government agency for advice on recycling programs and for where used fluids and filters can be properly disposed of in your area.  Fuel", "programs and for where used fluids and filters can be properly disposed of in your area.  Fuel Filter Replacement \u2014 Diesel Engine Ensure engine is turned off.  Remove the fuel filter protective cover to access the fuel filter assembly.  Fuel filter assembly 1 \u2014 retainers 2 \u2014 fuel filter protective cover place drain pan under the fuel filter assembly.  Open the water drain valve, and let any accumulated water and fuel drain.  Close the water drain valve.  Fuel filter assembly 1 \u2014 water drain valve wipe clean the underside of the filter housing to prevent contamination from entering fuel system during service.  Remove the fuel filter cap and filter from the housing using a socket.  Rotate counterclockwise for removal.  Fuel filter assembly 1 \u2014 fuel filter cap 2 \u2014 socket adapter remove the used fuel filter cartridge from the cap and dispose of according to your local regulations.  Wipe clean the sealing surfaces of the cap and housing.  Caution: take care when handling the new fuel filter to prevent", "surfaces of the cap and housing.  Caution: take care when handling the new fuel filter to prevent contamination from entering the fuel system.  Lubricate o-ring on the cap with clean engine oil.  Install the new fuel filter cartridge onto the cap.  Insert the cap and filter into the housing with clockwise rotation, use a socket to tighten.  After engine start, verify the fuel filter cap does not leak.  Note: Using a fuel filter that does not meet FCA US LLC filtration and water separating requirements can severely impact fuel system life and reliability.  CAUTION: Diesel fuel will damage blacktop paving surfaces.  Drain the filter into an appropriate container.  Do not prefill the fuel filter when installing a new fuel filter.  There is a possibility debris could be introduced into the fuel filter during this action.  It is best to install the filter dry and allow the in-tank lift pump to prime the fuel system.  Fuel/Water Separator Filter Do not drain the fuel/water separator filter when the engine is", "Fuel/Water Separator Filter Do not drain the fuel/water separator filter when the engine is running.  Diesel fuel will damage blacktop paving surfaces.  Drain the filter into an appropriate container.  If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage", "Volume & On/Off Control Push the VOLUME & On/Off control knob to turn on and off the Uconnect system.  The electronic volume control turns continuously (360 degrees) in either direction, without stopping.  Turning the VOLUME & On/Off control knob clockwise increases the volume, and counterclockwise decreases it.  When the audio system is turned on, the sound will be set at the same volume level as last played.  Steering Wheel Audio Controls The remote sound system controls are located on the rear surface of the steering wheel at the three and nine o\u2019clock positions.  The right-hand control is a rocker-type switch with a push button in the center and controls the volume and mode of the sound system.  Pushing the top of the rocker switch will increase the volume, and pushing the bottom of the rocker switch will decrease the volume.  Pushing the right-hand control\u2019s center button will make the radio switch between the various modes available (AM/FM/SXM or Media, etc.).  The left-hand control is a rocker-type", "the various modes available (AM/FM/SXM or Media, etc.).  The left-hand control is a rocker-type switch with a push button in the center.  The function of the left-hand control is different depending on which mode you are in.  The following describes the left-hand control operation in each mode:  Adjustable Chime Volume Settings The Front and Rear chime volume settings are programmable.  The settings may be programmed through the Uconnect systemThe chime volume settings include low, medium, and high.  The factory default volume setting is medium.  ParkSense will retain its last known configuration state through ignition cycles.", "Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure", "30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are", "pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  See the following steps for refueling: The vehicle may be equipped with a", "serious injury or death.  See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose", "the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.", "and power steering, and fill as needed.  Check function of all interior and exterior lights.  AUTOMATIC TRANSMISSION \u2014 IF EQUIPPED You must press and hold the brake pedal while shifting out of PARK.  WARNING: Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to", "and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock", "always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  CAUTION: Shift into or out of PARK or REVERSE only after the vehicle has come to a complete stop.  Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed.  Before shifting into any gear, make sure your foot is firmly pressing the brake pedal.  PARK (P) This range supplements the parking brake by locking the", "firmly pressing the brake pedal.  PARK (P) This range supplements the parking brake by locking the transmission.  The engine can be started in this range.  Never attempt to use PARK while the vehicle is in motion.  Apply the parking brake when exiting the vehicle in this range.  When parking on a hill, apply the parking brake before shifting the transmission to PARK.  As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  When exiting the vehicle, always: apply the parking brake shift the transmission into park turn the ignition off remove the key fob from the vehicle the following indicators should be used to ensure that you have properly engaged the transmission into the park position: when shifting into park, push the lock button on the gear selector and firmly move the gear selector all the way forward until it stops and is fully seated.  Look at the transmission gear position display and verify that it indicates the PARK position", "Look at the transmission gear position display and verify that it indicates the PARK position (P), and is not blinking.  With the brake pedal released, verify that the gear selector will not move out of PARK.  Note: On four-wheel drive vehicles, be sure that the transfer case is in a drive position.  WARNING: Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely", "indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the", "transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  CAUTION: Before moving the transmission gear selector out of PARK, you must start the engine, and also press the brake pedal.  Otherwise, damage to the gear selector could result.  DO NOT race the engine when shifting from PARK or NEUTRAL", "to the gear selector could result.  DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain.", "Door Frame Installation Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten fasteners target torque specification for torx fasteners maximum minimum 44.2 in-lb (5 n\u00b7m) 53.1 in-lb (6 n\u00b7m) 35.4 in-lb (4 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of", "door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step five step five insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  To remove the half-doors, repeat the installation steps in reverse order.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to", "from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate", "not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  If the check arm is stuck inside the door, follow these instructions to install the check arm.  To reinstall the door(s), perform the previous steps in the reverse order.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  To install the front door exterior mirrors on the half-doors, proceed as follows: To install the front or rear half-doors, proceed as follows: Locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place Tool Into Service Hole Of Plug To Remove Using the tool, slowly pull upwards from the center of the plug to remove.  Upon first", "To Remove Using the tool, slowly pull upwards from the center of the plug to remove.  Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  Only adjust the door to fit correctly against the striker.  DO NOT adjust the striker, as this could affect the positioning of the full door.  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.", "door frame.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door", "Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The rear door frames must be removed first, followed by the front door frames.  Loosen (do not remove) the four bolts on the door hinges", "first, followed by the front door frames.  Loosen (do not remove) the four bolts on the door hinges using the provided #T50 Torx head driver.  Hinge Bolt Locations Do not adjust the body mounted hinges, or any part of the door latch, as modifications to these parts will affect installation of the full door.  With the bolts loose, the door can be moved forward by pushing the door handle toward the front of the vehicle, and/or upward by grabbing the door handle and lifting towards the roof.  Once the gaps between the door and vehicle body are uniform around the entire door, tighten the door hinge bolts to 20.3 ft\u00b7 lb / 27.5 N\u00b7m (Max Torque: 27.3 ft\u00b7 lb / 37 N\u00b7m).  Lift upward on each section of the seat bottom.  Lift From Beneath Seat (Left Side Shown) Raise the seat bottom upward into the Stadium Position.  Stadium Position If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top If your vehicle is equipped with a soft top, the top must be lowered", "installation of the hard top If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Determine which door is affected.  Open the affected door and hold a dollar-size piece of paper along the top of the door opening against the vehicle near where the leak/noise was observed.  Make sure half of the paper is above the area where the door seal contacts the door opening, while the other half is below.  Close the door on the paper, then pull the paper upward.  If the paper moves with little to no effort, the upper half-door will need to be adjusted in that area to increase seal compression.  Performing A Paper Test Push Upward On Middle Of Upper Half Door To Remove", "The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended: A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  A long break-in period is not required for the engine and drivetrain (transmission and axle) in", "A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.", "recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which", "type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.", "Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain", "Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  CAUTION: If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage", "On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the", "seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not", "shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Press and release this button to turn the Climate Control ON/OFF.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  To Turn Off The Engine Using The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control will turn off, but Stability Control will remain active.  Hold the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC", "the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to", "turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the", "(A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine", "normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the", "ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.", "Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam", "the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.  Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Automatic Dimming Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  This mirror automatically adjusts for", "be adjusted to center on the view through the rear window.  This mirror automatically adjusts for headlight glare from vehicles behind you.  The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Note: The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  Automatic High Beam Headlamp Control \u2014 If Equipped The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automatically controlling the high beams through the use of a camera mounted on the vehicle\u2019s header.  This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.  Note: the automatic high beam headlamp control can be turned on or", "vehicle is out of view.  Note: the automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.", "Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Important Safety Precautions Please", "the seat belt, which could result in serious injury or death.  Important Safety Precautions Please pay close attention to the information in this section.  It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.  Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: Children 12 years old and under should always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint Never allow children to slide the shoulder belt behind them or under their arm.  You should read the instructions provided with your child restraint to make sure that you are using it", "should read the instructions provided with your child restraint to make sure that you are using it properly.  All occupants should always wear their lap and shoulder belts properly.  The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate.  Do not lean against the door or window.  If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.  If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see \"\u21e8if you need assistance\" for customer service contact information.  WARNING: Never place a rear-facing child restraint in front of an air bag.  A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.  Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing", "Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing child restraint in the rear seat.  If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle.  Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  The front passenger seat", "the desired position is reached and the seatback will lock into place.  The front passenger seat is unoccupied or has very light objects in it.  The front passenger seat is occupied by a rear-facing child restraint.  The front passenger seat is occupied by a child, including a child seated in a forward-facing child restraint or booster seat.  The front passenger seat is occupied by a small passenger, including a child or small adult.  The front passenger is not properly seated or his or her weight is taken off of the seat for a period of time.  Turn off the vehicle and have the adult passenger step out of the vehicle.  Remove any extra materials from the passenger seat, such as cushions, pads, seat covers, seat massagers, blankets, extra clothing, etc.  Place the seatback in the full upright position.  Have the adult passenger sit in the center of the seat, with the passenger\u2019s feet comfortably on or near the floor, and with their back against the seatback.  Restart the vehicle and have the passenger remain", "floor, and with their back against the seatback.  Restart the vehicle and have the passenger remain in this seated position for two to three minutes after restarting the vehicle.  The outboard front passenger seat BeltAlert is not active when the outboard front passenger seat is unoccupied.  BeltAlert may be triggered when an animal or other items are placed on the outboard front passenger seat or when the seat is folded flat (if equipped).  It is recommended that pets be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts, and cargo is properly stowed.  The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped) Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not", "locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  Be certain that the seatback is securely locked into position.  Perform a \u201cpush - pull - push\u201d check to confirm the seat is fully locked.  If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers.  A red indicator on the pull strap will be displayed if the seatback is not securely locked.  An improperly latched seat could cause serious injury.", "The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be", "rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds,", "your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional", "vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.", "JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in", "pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical", "in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the", "connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these", "in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.  Note: Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle while making connections.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack,", "alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two", "Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and", "Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have", "discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.", "Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset", "section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start", "The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will", "Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.", "If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used", "the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered", "fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank", "escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light", "cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's", "do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see \"\u21e8draining fuel/water separator filter \u2014 diesel engine\" .", "See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a", "See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the", "Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can", "lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  To Reset The Manual Park Release: Pull upward on the tether strap, releasing it from the \u201clocked\u201d position.  Lower the Manual Park Release lever downward into its original position.  Original tether position tuck the tether strap into the base of the", "into its original position.  Original tether position tuck the tether strap into the base of the console, and reinstall the cover.  Extended Park Starting Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Note: Extended Park condition occurs when the vehicle has not been started or driven for at least 30 days.  CAUTION: To prevent damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.", "Automatic Operation Push the AUTO button on the faceplate, or the AUTO button on the touchscreen on the Automatic Temperature Control (ATC) Panel.  Next, adjust the temperature that you would like the system to maintain by adjusting the driver and passenger temperature control buttons.  Once the desired temperature is displayed, the system will achieve and automatically maintain that comfort level.  When the system is set up for your comfort level, it is not necessary to change the settings.  You will experience the greatest efficiency by simply allowing the system to function automatically.  To provide you with maximum comfort in the Automatic mode during cold start-ups, the blower fan will remain on low until the engine warms up.  The blower will increase in speed and transition into Auto mode.  Note: It is not necessary to move the temperature settings for cold or hot vehicles.  The system automatically adjusts the temperature, mode, and blower speed to provide comfort as quickly as possible.  The", "adjusts the temperature, mode, and blower speed to provide comfort as quickly as possible.  The temperature can be displayed in U.S. Or metric units by selecting the u.s./metric customer-programmable feature within uconnect settings \"\u21e8uconnect settings\" .  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Weather control settings hot weather and vehicle interior is very hot set the mode control to (panel mode), (max a/c) on, and blower on high.  Roll down the windows for a minute to flush out the hot air.  Adjust the controls as needed to achieve comfort.  Warm weather turn (a/c) on and set the mode control to (panel mode).  Cool sunny operate in (bi-level mode).  Cool & humid conditions set the mode control to (mix mode) and turn on (a/c) to keep windows clear.  Cold weather set the mode control to (floor mode).  If windshield fogging starts to occur,", "clear.  Cold weather set the mode control to (floor mode).  If windshield fogging starts to occur, move the control to (mix mode).  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is", "an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid", "could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.", "Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard Top Panel(s) Storage Bag \u2014", "that are used when the hard top is not installed on the vehicle.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top", "the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or", "vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure", "the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the", "in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric", "with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.", "This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  This warning light indicates the Electronic Stability Control (ESC) is off.  The ESC OFF Indicator Light indicates that the Electronic Stability Control (ESC) is in a reduced mode.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.", "is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  The behavior of Electronic Stability Control while in Off Road+ varies depending on the 4WD status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also, holding the ESC OFF button for five seconds will turn off ESC.  In 4WD Low, Electronic Stability Control automatically shuts off regardless of the Off Road Status.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be", "the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not attempt to drive the vehicle over 18 mph (29 km/h).  Driving faster than 18 mph (29 km/h) with a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  The ESC Activation/Malfunction Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN mode.  It should go out with the engine running.  If the ESC Activation/Malfunction Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  This warning light will turn on when there's a fault with the EPS system  Electronic Stability Control (ESC) Active", "will turn on when there's a fault with the EPS system  Electronic Stability Control (ESC) Active Warning Light \u2014 If Equipped This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is", "position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.  Monitoring battery level status led light red 40% or lower yellow 40% to 70% green 70% to 100% electronic stability control (esc) active warning light \u2014 if equipped this warning light will indicate when the electronic stability control system is active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem", "greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.  Adaptive Cruise Control (ACC) Set Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.", "Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an", "information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system", "personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL", "your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.", "ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System.  This feature is a communication network that takes effect in the event of an impact \"\u21e8enhanced accident response system\" .  ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System.  This feature is a communication network that takes effect in the event of an impact Enhanced accident response system in the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the occupant restraint controller (orc) will determine whether to have the enhanced accident response system perform the following functions: cut off fuel to the engine (if equipped) cut off battery power to the electric motor (if equipped) flash hazard lights as long as the battery has power turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the", "which remain on as long as the battery has power or for 15 minutes from the intervention of the enhanced accident response system unlock the power door locks your vehicle may also be designed to perform any of these other functions in response to the enhanced accident response system: turn off the fuel filter heater, turn off the hvac blower motor, close the hvac circulation door cut off battery power to the: engine electric motor (if equipped) electric power steering brake booster electric park brake automatic transmission gear selector horn front wiper note: after an accident, remember to cycle the ignition to the stop (off/lock) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset", "fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.  Automatic SOS \u2014 If Equipped Automatic SOS is a hands-free safety service that can immediately connect you with help in the event that your vehicle\u2019s airbags deploy.  Please refer to your provided radio", "you with help in the event that your vehicle\u2019s airbags deploy.  Please refer to your provided radio supplement for complete information.", "The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.", "driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  Off-Road Driving Tips  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of", "You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and", "too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the", "setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic mode \"\u21e8automatic operation\" .  A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected,", "increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  To Deactivate A soft tap on the brake pedal, pushing the CANC (cancel) button, or normal brake pressure while slowing the vehicle will deactivate the Cruise Control without erasing the set speed from memory.  The following conditions will also deactivate the cruise control without erasing the set speed from memory: vehicle parking brake is applied stability event occurs gear selector is moved out of drive engine overspeed occurs clutch pedal is pressed (manual transmission only) vehicle is operating at a low rpm (manual transmission only) pushing the on/off button or placing the ignition in the off position, erases the set speed from memory.  Recirculation Button Push the Recirculation button on the faceplate", "the set speed from memory.  Recirculation Button Push the Recirculation button on the faceplate to change the system between recirculation mode and outside air mode.  The Recirculation indicator and the A/C indicator (if equipped) illuminate when the Recirculation button is pressed.  Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.  Recirculation can be used in all modes except for Defrost.  Recirculation may be unavailable if conditions exist that could create fogging on the inside of the windshield.  The A/C can be deselected manually without disturbing the mode control selection.  Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur.  Extended use of this mode is not recommended.  On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode to improve window clearing operation.  Recirculation is disabled automatically if this mode is selected.  Attempting to use", "operation.  Recirculation is disabled automatically if this mode is selected.  Attempting to use Recirculation while in this mode causes the LED on the control button to blink and then turn off.", "FOLDING WINDSHIELD The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element provides.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded", "belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  WARNING: Carefully follow these warnings to help protect against personal injury: Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raising The Windshield Release the strap that secured the windshield in the", "cause personal injury.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshieldUsing the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Cleaning Instructions During", "make sure the windshield is raised prior to installing the tops.  Cleaning Instructions During windshield down applications, dust/dirt can accumulate in the cover and block the camera lens.  Use a microfiber cloth to clean the camera lens, module, and inside cover, being careful not to damage or scratch the module.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a", "driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will", "longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may", "and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.", "Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Console Storage Compartment The center console has both an upper and lower", "the floor are removed.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by", "Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as", "The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.", "Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d The buttons on the right side of the steering wheel operate the ACC system.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged ACC Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following appears in the instrument cluster display:  To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.", "To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d WARNING: Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous.  You could accidentally set the system or cause it to go faster than you want.  You could lose control and have a collision.  Always leave the system off when you are not using it.  Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.", "Intermittent Wipers Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.  Rotate the end of the lever to the first detent position for one of four intermittent settings.  The delay cycle can be set anywhere between 1 to 18 seconds.  Note: The wiper delay times depend on vehicle speed.  If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled.  Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.  Rotate the end of the lever to the first detent position for one of four intermittent settings.  The delay cycle can be set anywhere between 1 to 18 seconds.  Intermittent Wipers Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  Windshield Washers To use the", "past the intermittent settings for high-speed wiper operation.  Windshield Washers To use the washer, pull the lever toward you and hold until desired spray is reached.  If the lever is pulled while in the delay range, the wiper will start and continue to operate for two or three wipe cycles after the lever is released.  Then, the intermittent interval previously selected will resume.  If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles.  Then, the wipers will turn off.  Note: As a protective measure, the washer will stop if the switch is held for more than 20 seconds.  Once the switch is released the washer will resume normal operation.  WARNING: Sudden loss of visibility through the windshield could lead to a collision.  You might not see other vehicles or other obstacles.  To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.", "Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an", "information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system", "personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL", "your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.", "What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the", "start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from", "with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery", "disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Battery Saver On, Battery Saver Mode Message, And Electrical Load Reduction Actions (If Equipped) This vehicle is equipped with an Intelligent Battery Sensor (IBS) to perform additional monitoring of the electrical system and status of the vehicle battery.  In cases when the IBS detects charging system failure, or the vehicle battery conditions are deteriorating, electrical load reduction actions will take place to extend the driving time and distance of the vehicle.  This is done by reducing power to or turning off non-essential electrical loads.  Load reduction is only active when the engine is running.  It will display a message if there is a risk of battery depletion to the point where the vehicle may stall due to lack of electrical supply, or will not restart after the current drive", "the vehicle may stall due to lack of electrical supply, or will not restart after the current drive cycle.  When load reduction is activated, the message \u201cBattery Saver On Some Systems May Have Reduced Power\u201d will appear in the instrument cluster.  These messages indicate the vehicle battery has a low state of charge and continues to lose electrical charge at a rate that the charging system cannot sustain.  The electrical loads that may be switched off (if equipped), and vehicle functions which can be affected by load reduction: heated seat/vented seats/heated wheel rear defroster and heated mirrors hvac system 115 volt ac power inverter system audio and telematics system loss of battery charge may indicate one or more of the following conditions: the charging system cannot deliver enough electrical power to the vehicle system because the electrical loads are larger than the capability of the charging system.  The charging system is still functioning properly.  Turning on all possible vehicle electrical", "The charging system is still functioning properly.  Turning on all possible vehicle electrical loads (e.g.  HVAC to max settings, exterior and interior lights, overloaded power outlets +12 Volt, 115 Volt AC, USB ports) during certain driving conditions (city driving, towing, frequent stopping).  Installing options like additional lights, upfitter electrical accessories, audio systems, alarms and similar devices.  Unusual driving cycles (short trips separated by long parking periods).  The vehicle was parked for an extended period of time (weeks, months).  The battery was recently replaced and was not charged completely.  The battery was discharged by an electrical load left on when the vehicle was parked.  The battery was used for an extended period with the engine not running to supply radio, lights, chargers, +12 Volt portable appliances like vacuum cleaners, game consoles and similar devices.  Note: The charging system is independent from load reduction.  The charging system performs a diagnostic on the", "system is independent from load reduction.  The charging system performs a diagnostic on the charging system continuously.  If the battery charge warning light is on it may indicate a problem with the charging system \"\u21e8battery charge warning light\" .", "Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To", "floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.  Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten", "the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.", "To engage REVERSE gear from the NEUTRAL position, lift the REVERSE ring, located below the knob and move the gear selector all the way left and then forward.  If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  To shift the gears, fully press the clutch pedal and place the gear selector into the desired gear position (the diagram for the engagement of the gears is displayed on the handle of the selector).  The gear position will be displayed in the instrument cluster.  Operation To activate AutoStick mode, move the gear selector into the MANUAL (M) position (beside the DRIVE position).  The current transmission gear will be displayed in the instrument cluster.  In AutoStick mode,", "The current transmission gear will be displayed in the instrument cluster.  In AutoStick mode, you can use the gear selector (in the MANUAL position) to manually shift the transmission.  Tapping the gear selector forward (-) while in the MANUAL (M) position will downshift the transmission to the next lower gear.  Tapping the selector rearward (+) will command an upshift.  In AutoStick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result.  It will remain in the selected gear until another upshift or downshift is chosen, except as follows: The transmission will automatically downshift as the vehicle slows (to prevent engine lugging) and will display the current gear.  The transmission will automatically downshift to FIRST gear when coming to a stop.  After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or", "as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or THIRD gear, in 4L range).  Tapping (+) (at a stop) will allow starting in SECOND gear.  Starting out in SECOND or THIRD gear can be helpful in snowy or icy conditions.  If a requested downshift would cause the engine to overspeed, that shift will not occur.  The system will ignore attempts to upshift at too low of a vehicle speed.  Holding the gear selector in the (-) position will downshift the transmission to the lowest gear possible at the current speed.  Transmission shifting will be more noticeable when AutoStick is enabled.  The system may revert to automatic shift mode if a fault or overheat condition is detected.  To disengage AutoStick mode, return the gear selector to the DRIVE position.  You can shift in or out of the AutoStick position at any time without taking your foot off the accelerator pedal.  Note: When Hill Descent Control is enabled, AutoStick is not active.  WARNING: Do not downshift for", "Note: When Hill Descent Control is enabled, AutoStick is not active.  WARNING: Do not downshift for additional engine braking on a slippery surface.  The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.", "Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.", "Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately \"\u21e8air bag warning light\" .  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning", "as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bags to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Placing an object on", "you drive, have an authorized dealer service the air bag system immediately.  Placing an object on the floor under the front passenger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision.  Do not place any objects on the floor under the front passenger seat.  If there is a fault present in the OCS, both the PAD Indicator Light and the Air Bag Warning Light will illuminate to show that the Passenger Advanced Front Air Bag is deactivated.  Should this occur, the Passenger Advanced Front Air Bag will remain deactivated until the fault is cleared.  This indicates that you should take the vehicle to an authorized dealer for service immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light", "Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light will illuminate whenever the ocs is unable to classify the front passenger seat status.  A malfunction in the OCS may affect the operation of the air bag system.  If the air bag warning light does not come on, or stays on after you start the vehicle, or it comes on as you drive, take the vehicle to an authorized dealer for service immediately.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check", "Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Air Bag Warning Light This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on", "stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  Air Bag Warning Light The Occupant Restraint Controller (ORC) monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position.  If the ignition switch is in the OFF position or in the ACC position, the air bag system is not on and the air bags will not inflate.  The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or it becomes disconnected prior to deployment.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light,", "If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is detected that could affect the air bag system.  The diagnostics also record the nature of the malfunction.  While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  Note: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint", "the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled.  In this condition the air bags may not be ready to inflate for your protection.  have an authorized dealer service the air bag system immediately.  WARNING: Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.", "Manual Seat Height Adjustment The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.  Manual Front Seat Forward/Rearward Adjustment The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  WARNING: Adjusting a seat while driving may be dangerous.  Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death.  Seats should be adjusted before fastening the seat belts and while the", "serious injury or death.  Seats should be adjusted before fastening the seat belts and while the vehicle is parked.  Serious injury or death could result from a poorly adjusted seat belt.  Lumbar Support The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  Manual Seat Height Adjustment The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.  Adjustable Upper Shoulder Belt Anchorage In the driver and outboard front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck.  Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that", "squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.  As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position.  After you release the anchorage button, try to move it up or down to make sure that it is locked in position.  Note: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature.  This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release button.  To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position.  WARNING: Wearing your seat belt incorrectly could make your injuries in a collision much worse.  You might suffer internal injuries, or you could even slide out of the seat belt.  Follow these instructions to wear your seat", "or you could even slide out of the seat belt.  Follow these instructions to wear your seat belt safely and to keep your passengers safe, too.  Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and not resting on your neck.  The retractor will withdraw any slack in the shoulder belt.  Misadjustment of the seat belt could reduce the effectiveness of the safety belt in a crash.  Always make all seat belt height adjustments when the vehicle is stationary.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.", "your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Secondary Method For Oil Change Reset Procedure Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the", "pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Note: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.  If necessary, repeat this procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be", "(805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in", "with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means", "Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000", "follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a", "dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both", "the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the", "If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your", "involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm", "one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system", "is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a", "Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  When the Display button is pressed on the touchscreen, the system will display the options related to the theme (if equipped), brightness, and color of the touchscreen.  The available settings are: note: depending on the vehicle\u2019s options, feature settings may vary.  MAX A/C Button Press and release the MAX A/C button on the touchscreen to change the current setting to the coldest output of air.  MAX A/C sets the control for maximum cooling performance.  The MAX A/C indicator illuminates when MAX A/C is on.  Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.  Note:", "the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.  Note: The MAX A/C button is only available on the touchscreen.", "Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada) symbols key if you do not read the entire owner\u2019s manual, you may miss important information.  Observe all Cautions and Warnings.  Service Manuals These comprehensive Service Manuals provide a complete working knowledge of the vehicle, system, and/or components and is written in straightforward language with illustrations, diagrams, and charts.  Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage Owner's Manuals, Radio Manuals and Warranty Information Books", "Vehicle delivery date and mileage Owner's Manuals, Radio Manuals and Warranty Information Books can be ordered through Archway at: To order the following manuals, you may use either the website or the phone numbers listed below.  Owner's Manuals If you do not read the entire Owner\u2019s Manual, you may miss important information.  Observe all Cautions and Warnings.  Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada).", "Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all", "system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a", "testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you", "ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the", "going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the", "The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "The Uconnect system is a sophisticated electronic device.  Do not let young children use the system.  Permanent hearing loss may occur if you play your music or sound system at loud volumes.  Exercise caution when setting the volume on the system.  Keep drinks, rain and other sources of moisture away from the system.  Besides damage to the system, moisture can cause electric shocks as with any electronic device.  It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.  Uconnect Phone is a voice-activated, hands-free, in-vehicle communications system.  It allows you to dial a phone number with your mobile phone.  Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling contacts", "Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling contacts from Phonebooks displayed on the touchscreen.  Setting Favorite Contact phone numbers so they are easily accessible on the Main Phone screen.  Viewing and Calling contacts from Recent Call logs.  Reviewing your recent Incoming SMS Messages.  Pairing up to 10 phones/audio devices for easy access to connect to them quickly.  Your mobile phone\u2019s audio is transmitted through your vehicle\u2019s audio system; the system will automatically mute your radio when using the Uconnect Phone.  For uconnect customer support: us visit uconnectphone.com or call 877-855-8400 canada visit uconnectphone.com or call 800-465-2001 (english) or (french) call 800-387-9983 uconnect phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile", "conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  Note: Your phone must be capable of SMS messaging via Bluetooth\u00ae for messaging features to work properly.  WARNING: ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the Uconnect features and applications in this vehicle.  Only use Uconnect when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Safe Usage Of The Uconnect System The", "may result in an accident involving serious injury or death.  Safe Usage Of The Uconnect System The Uconnect system is a sophisticated electronic device.  Do not let young children use the system.  Permanent hearing loss may occur if you play your music or sound system at loud volumes.  Exercise caution when setting the volume on the system.  Keep drinks, rain and other sources of moisture away from the system.  Besides damage to the system, moisture can cause electric shocks as with any electronic device.  Note: Many features of this system are speed dependent.  For your own safety, it is not possible to use some of the touchscreen features while the vehicle is in motion.  Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling contacts from Phonebooks displayed on the touchscreen.  Setting Favorite Contact phone numbers so they are easily accessible on the Main Phone screen.  Viewing and Calling contacts from Recent Call logs.  Reviewing your recent Incoming SMS Messages.", "Viewing and Calling contacts from Recent Call logs.  Reviewing your recent Incoming SMS Messages.  Pairing up to 10 phones/audio devices for easy access to connect to them quickly.  Your mobile phone\u2019s audio is transmitted through your vehicle\u2019s audio system; the system will automatically mute your radio when using the Uconnect Phone.  For uconnect customer support: us visit uconnectphone.com or call 877-855-8400 canada visit uconnectphone.com or call 800-465-2001 (english) or (french) call 800-387-9983 uconnect phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been", "wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  Note: Your phone must be capable of SMS messaging via Bluetooth\u00ae for messaging features to work properly.  WARNING: ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the Uconnect features and applications in this vehicle.  Only use Uconnect when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Multiple Devices Connecting To The Uconnect System \u2014 If Equipped It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text", "CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.  Note: Apple CarPlay\u00ae and Android Auto\u2122 can only be launched from the front and center console USB ports.", "Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be", "these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the", "upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside),", "Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.", "or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels", "top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Remove both front panels Open both front doors.  Using the provided #50 Torx head driver and ratchet, remove the two Torx head", "both front doors.  Using the provided #50 Torx head driver and ratchet, remove the two Torx head screws that secure the hard top at the B-pillar (near the top of the front doors).  Step Three If equipped, remove the lower interior soft trim panel (attached by the hook-and-loop fastener) by pulling the panel away from the trim.  Step Four Remove the Torx head fasteners that secure the hard top to the vehicle: two along the interior body side, rearward of the back doors, followed by the four fasteners along the back of the vehicle cab using the #T50 Torx head driver.  Step Five 1 \u2014 Vehicle Cab Torx Head Fasteners 2 \u2014 Body side Torx Head Fasteners Locate the wire harness on the left rear inside corner of the vehicle.  To access the harness, remove the plastic cover by pushing the cover to the side, and sliding it off.  Do not force open; this will break the plastic cover.  Step Six To release the wire harness, pull back on the red latch (1), then push down on the black button (2) while pulling the harness out.", "back on the red latch (1), then push down on the black button (2) while pulling the harness out.  Step Seven 1 \u2014 Red Latch 2 \u2014 Black Button Remove the hard top from the vehicle.  Install the provided edge protectors along the bottom edges of the hard top, and place the hard top on a soft surface to prevent damage.  The removal of the Hard Top requires four adults located on each corner.  Failure to follow this caution could damage the Hard Top.  Store the wire harness by removing the storage cover on the quarter trim.  Use the mechanical key blade to pry the cover open.  Step Nine Tuck the wire harness inside the storage compartment, and replace the cover.", "Battery Charge Warning Light This warning light will illuminate when the battery is not charging properly.  If it stays on while the engine is running, there may be a malfunction with the charging system.  Contact an authorized dealer as soon as possible.  This indicates a possible problem with the electrical system or a related component.  Battery Charge Warning Light This warning light will illuminate when the battery is not charging properly.  If it stays on while the engine is running, there may be a malfunction with the charging system.  Contact an authorized dealer as soon as possible.  This indicates a possible problem with the electrical system or a related component.  Red warning lights air bag warning light \"\u21e8air bag warning light\" brake warning light \"\u21e8brake warning light\" battery charge warning light \"\u21e8battery charge warning light\" door open warning light \"\u21e8door open warning light\" electric power steering (eps) fault warning light \"\u21e8electric power steering (eps) fault warning light\" electronic", "steering (eps) fault warning light \"\u21e8electric power steering (eps) fault warning light\" electronic throttle control (etc) warning light \"\u21e8electronic throttle control (etc) warning light\" engine coolant temperature warning light \"\u21e8engine coolant temperature warning light\" hood open warning light \"\u21e8hood open warning light\" oil pressure warning light \"\u21e8oil pressure warning light\" oil temperature warning light \"\u21e8oil temperature warning light\" seat belt reminder warning light \"\u21e8seat belt reminder warning light\" rear seat belt reminder warning light \"\u21e8rear seat belt reminder indicator light \u2014 if equipped with a base instrument cluster\" transmission temperature warning light \"\u21e8transmission temperature warning light \u2014 if equipped\" vehicle security warning light \"\u21e8vehicle security warning light \u2014 if equipped\" loose fuel filler cap warning light \u2014 if equipped this warning light will illuminate when the fuel filler cap is loose.  Properly close the filler cap to disengage the light.  If the light does not turn off,", "is loose.  Properly close the filler cap to disengage the light.  If the light does not turn off, please see an authorized dealer.  The charging system is independent from load reduction.  The charging system performs a diagnostic on the charging system continuously.  If the Battery Charge Warning Light is on it may indicate a problem with the charging system This warning light will illuminate when the battery is not charging properly.  If it stays on while the engine is running, there may be a malfunction with the charging system.  Contact an authorized dealer as soon as possible.  Red Warning Lights Air Bag Warning Light \"\u21e8Air Bag Warning Light\" Brake Warning Light \"\u21e8Brake Warning Light\" Battery Charge Warning Light \"\u21e8Battery Charge Warning Light\" Door Open Warning Light \"\u21e8Door Open Warning Light\" Electric Power Steering (EPS) Fault Warning Light \"\u21e8Electric Power Steering (EPS) Fault Warning Light\" Electronic Throttle Control (ETC) Warning Light \"\u21e8Electronic Throttle Control (ETC) Warning Light\" Engine", "Throttle Control (ETC) Warning Light \"\u21e8Electronic Throttle Control (ETC) Warning Light\" Engine Coolant Temperature Warning Light \"\u21e8Engine Coolant Temperature Warning Light\" Hood Open Warning Light \"\u21e8Hood Open Warning Light\" Oil Pressure Warning Light \"\u21e8Oil Pressure Warning Light\" Oil Temperature Warning Light \"\u21e8Oil Temperature Warning Light\" Seat Belt Reminder Warning Light \"\u21e8Seat Belt Reminder Warning Light\" Rear Seat Belt Reminder Warning Light \"\u21e8Rear Seat Belt Reminder Indicator Light \u2014 If Equipped With A Base Instrument Cluster\" Transmission Temperature Warning Light \"\u21e8Transmission Temperature Warning Light \u2014 If Equipped\" Vehicle Security Warning Light \"\u21e8Vehicle Security Warning Light \u2014 If Equipped\" This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced", "is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  With extended use the Hazard Warning Flashers may wear down your battery.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a", "indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  This warning light will illuminate when the Stop/Start system is not functioning properly and service is required.  Contact an authorized dealer for service.  This warning light will turn on when there's a fault with the EPS system The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.", "AUTOMATIC TRANSMISSION \u2014 IF EQUIPPED You must press and hold the brake pedal while shifting out of PARK.  WARNING: Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not", "to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked", "and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  CAUTION: Shift into or out of PARK or REVERSE only after the vehicle has come to a complete stop.  Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed.  Before shifting into any gear, make sure your foot is firmly pressing the brake pedal.  Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle", "brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift", "or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned", "of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  You or others could be injured or killed if you leave the", "of all interior and exterior lights.  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied.  The parking brake should always be applied when the driver is not in the vehicle, especially on an incline.  Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the", "and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or", "in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.", "Replacing The Battery In The Key Fob The recommended replacement battery is CR2450.  Remove the back cover of the key fob by inserting a flat-blade screwdriver into the slot on the bottom of the fob.  Apply light pressure until the cover unsnaps being careful not to damage the seal.  Proceed counterclockwise (in the order shown in the following image) to loosen the remaining snaps until the battery cover can be removed.  1-3 \u2013 back cover pry points remove the depleted battery by inserting a small flat-blade screwdriver into the battery removal slot and sliding the battery forward and upward being careful not to damage the electronic board underneath.  Battery replacement install the new battery into the key fob, making sure the positive (+) side is facing up.  Slide the battery until it is seated securely below the tabs.  Reassemble the back cover making sure it is properly aligned before snapping it back in place.  Note: Customers are recommended to use a battery obtained from Mopar\u00ae.  Aftermarket coin", "in place.  Note: Customers are recommended to use a battery obtained from Mopar\u00ae.  Aftermarket coin battery dimensions may not meet the original OEM coin battery dimensions.  Perchlorate material \u2014 special handling may apply.  See www.dtsc.ca.gov/hazardouswaste/perchlorate for further information.  Do not touch the battery terminals that are on the back housing or the printed circuit board.  When a key fob battery is low, a warning will be indicated on the vehicle\u2019s instrument cluster, and the fob LED will no longer illuminate with a button push.  WARNING: The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop", "and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.", "facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical", "integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  The battery in your vehicle is located in the right rear of the engine compartment.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  The Power Distribution Center is located", "on the passenger side under the instrument panel.  The Power Distribution Center is located in the engine compartment near the battery.  This center contains cartridge fuses, mini fuses, and relays.  The PDC top cover is labeled with each serviceable fuse/relay location, function, and size.", "Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts", "After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.", "the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.", "A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  A/C Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Note: For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned", "For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause", "performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic mode \"\u21e8automatic operation\" .", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The rear seatback can be locked using the vehicle key to", "this caution could damage the hard top.  The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  This vehicle has front air bags and lap/shoulder belts for both the driver and front passenger.  The front air bags are a supplement to the seat belt restraint systems.  The driver front air bag is mounted in the center of the steering wheel.  The passenger front air bag is mounted in the instrument panel, above the glove compartment.  The words \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d are embossed on the air bag covers.  This vehicle has an Occupant Classification System (\u201cOCS\u201d) in the front passenger seat.  The OCS is designed to activate or deactivate the Passenger Advanced Front Air Bag depending on the occupant\u2019s seated weight.  It is designed to deactivate the Passenger Advanced Front Air Bag for an unoccupied seat and for occupants whose", "to deactivate the Passenger Advanced Front Air Bag for an unoccupied seat and for occupants whose seated weight classifies them in a category other than a properly seated adult.  This could be a child, teenager, or even an adult.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation.  The entire vehicle should first be weighed on a commercial scale to ensure that the GVWR has not been exceeded.  The weight on the front and rear of the vehicle should then be determined separately to be sure that the load is", "the front and rear of the vehicle should then be determined separately to be sure that the load is properly distributed over the front and rear axle.  Weighing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.  If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met.  Store the heavier items down low and be sure that the weight is distributed equally.  Stow all loose items securely before driving.  Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate.  WARNING: Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR.  If you do, parts on your vehicle can break, or it can change the way your vehicle handles.  This could cause you to lose control.  Overloading can shorten the life of your vehicle.", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the", "menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING:", "display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and", "mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Rear Seat Unoccupied Indicator Light \u2014 If Equipped This light indicates when the rear passenger seats are unoccupied, and will illuminate in the upper right portion of the instrument cluster display, momentarily replacing the configurable corner information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the", "information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed", "mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the", "vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR", "clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected", "time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If", "if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.", "may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory", "smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The", "engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse", "maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle", "or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.", "The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom", "Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage", "The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium", "below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.", "Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  If the \u201cSERVICE POWER STEERING\u201d", "Normal operation will resume once the system is allowed to cool.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function.  However, the effort required to brake the vehicle will be much greater than that required with the power system operating.  If the stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the", "stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not attempt to drive the vehicle over 18 mph (29 km/h).  Driving faster than 18 mph (29 km/h) with a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  When the condition that deactivated the system is no longer present, the system will return to the \u201cAdaptive Cruise Control Off\u201d state and will resume function by simply reactivating it.  There may be situations where the Hill Start Assist (HSA) will not activate and slight rolling may occur, such as on minor hills or with a loaded vehicle, or while pulling a trailer.  HSA is not a substitute for active driving involvement.  It is always the", "while pulling a trailer.  HSA is not a substitute for active driving involvement.  It is always the driver\u2019s responsibility to be attentive to distance to other vehicles, people, and objects, and most importantly brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision or serious personal injury.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized", "on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off CAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial", "it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may", "are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offCAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.", "To use the mid position, open the tailgate and lower it to near mid position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  Tailgate In Mid Position  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014", "the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located", "provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.", "Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the", "you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you", "is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  Getting High-Centered If you get hung up or", "every effort to cross the large rocks with your tires.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION:", "abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on", "Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.", "WARRANTY INFORMATION See the Warranty Information for the terms and provisions of FCA US LLC warranties applicable to this vehicle and market.  Refer to www.mopar.com/om for further information.  See the Warranty Information for the terms and provisions of FCA Canada Inc.warranties applicable to this vehicle and market.  Refer to www.owners.mopar.ca/en for further information.  Use this QR code to access your digital experience.  Who is Covered You are covered by Roadside Assistance services if you are a purchaser for use of the vehicle.  Roadside Assistance services last for five years or 60,000 miles on the odometer, whichever occurs first, calculated from the start date of the Basic Limited Warranty, as set forth in your Warranty Information book.  1 1.  Towing services provided through Cross Country Motor Club, Inc. Medford, MA 02155, except in AK,CA, HI, OR, WI, and WY, where services are provided by Cross Country Motor Club of California, Inc., Thousand Oaks, CA 91360.  Who is Covered You are covered", "Country Motor Club of California, Inc., Thousand Oaks, CA 91360.  Who is Covered You are covered by Roadside Assistance services if you are a purchaser for use of the vehicle.  Roadside Assistance services last for five years or 60,000 miles on the odometer, whichever occurs first, calculated from the start date of the Basic Limited Warranty, as set forth in your Warranty Information book.  1 1.  Towing services provided through Cross Country Motor Club, Inc.Medford, MA 02155, except in AK,CA, HI, OR, WI, and WY, where services are provided by Cross Country Motor Club of California, Inc., Thousand Oaks, CA 91360.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.", "your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil", "to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no", "completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator", "within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To", "this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will", "(805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on", "system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect", "against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.", "vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code", "leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants", "are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the", "the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric topDo not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top \u00b9 use", "installation can cause water to leak into the vehicle's interior.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top", "Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.", "Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1)", "and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  All cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  (1) Locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.\u201d on your vehicle's placard.  Opening To open the tailgate, pull the release handle located on the center of the tailgate", "Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two", "box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed,", "tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.", "Press the settings button on the touchscreen.  Press the paired phones or audio sources button.  Press to select the particular phone or the particular audio device.  A pop-up menu will appear; press \u201cConnect Phone\u201d.  Press the X to exit out of the Settings screen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The MAX A/C button is only available on the touchscreen.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and", "scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsThe SYNC button is only available on the touchscreen.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Press the Phone button.  Press the Dial/Keypad button on the touchscreen.  The Touch-Tone screen will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press", "will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press \u201cDial/Call\u201d.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  Overview Bluetooth\u00ae Streaming Audio or Bluetooth\u00ae Mode is entered by pairing a Bluetooth\u00ae device, containing music, to the Uconnect system.  Before proceeding, the Bluetooth\u00ae device must be paired to the Uconnect Phone to communicate with the Uconnect system.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark", "menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and", "the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow", "pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.", "Daytime Running Lights (DRLs) \u2014 If Equipped The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  Note: For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  Vehicles sold in Canada are equipped with a headlight switch with an AUTO", "(manual transmission).  Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  \"R\" means radial construction, or \"D\" means diagonal or bias construction Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered in the US and other countries.  Apple\u00ae terms of use and privacy statements apply.  Vehicles", "in the US and other countries.  Apple\u00ae terms of use and privacy statements apply.  Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic", "active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  BeltAlert can be activated or deactivated by an authorized dealer.  FCA US LLC does not recommend deactivating BeltAlert.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service", "is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors", "a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software,", "into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact", "you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by", "updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but", "engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.", "the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable", "The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the", "Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the", "Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "Replacing the wiring connector into the wiring harness to reinstall the wiring connector on the vehicle\u2019s door into the harness just inside the vehicle, proceed as follows: with light finger pressure, seat the wiring connector straight into the wiring harness until the wiring harness lever starts to lower with the latching pin.  Connecting the wiring harness 1 \u2014 seat connector straight into harness 2 \u2014 wiring harness lever starts to lower caution: failure to correctly reconnect the wiring connector into the harness will result in damage that is not covered by the new vehicle warranty.  After the harness lever has started to move with the pressure of seating the wiring connector, continue by lowering the wiring harness lever to the fully closed position.  Fully closed position push the red locking tab downward to lock into place.  Attach the cloth strap of the door onto the metal hook just inside the vehicle.  Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap replace wiring access doors.  Note: Make sure", "Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap replace wiring access doors.  Note: Make sure there is plenty of slack on the wiring connector during installation.  Close the door slightly to provide more slack if needed.  Note: When reinstalling the door check arm attachment screw, screw torque should be between 11.76 ft\u00b7lb / 16 N\u00b7m and 27.9 ft\u00b7lb / 38 N\u00b7m.  Rear door removal rear door removal \u00b9 use this qr code to access your digital experience.  To remove the rear doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nuts from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin under the rear seat.  Hinge pin nut slide the front seat(s) fully forward.  Pry open and remove the plastic wiring access door from the bottom of the B-pillar.  Wiring access door unplug the wiring connector.  Note: squeeze the tab on the base of the wiring harness.  This will unlock the connector tab,", "Note: squeeze the tab on the base of the wiring harness.  This will unlock the connector tab, allowing the wiring connector to be unplugged.  Unhook the wire harness strap from the hook on the body side.  Store the wire connector in the lower basket of the door.  Wiring connector with the door in the open position, remove the check bolt from the door check attachment on the body (using a #t40 torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  To reinstall the door(s), perform the previous steps in the reverse order.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear", "this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  WARNING: To avoid personal injury be sure to keep your arms, hands, fingers and all objects clear of the check arm area during the removal and installation procedures.  Note: The upper hinge has a longer pin, which can be used to assist in guiding the door into place when reinstalling.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb", "CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Installing The Rear Window And Quarter Panel Cover Assemblies If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: Guide the top of the quarter panel cover assembly up into the retainer.  Step one caution: failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the soft top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide", "corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide the rear window into the retainer while keeping the window level.  Step four engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step five engage the vertical retainers up the right and left side of the rear window.  Step six tuck the rear window under the soft top fabric and press firmly.  Step seven engage the rear window retainers in the lower right and left corners.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.", "Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  Manual", "for child seats and/or passengers.  An improperly latched seat could cause serious injury.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Important Safety Precautions Please pay close attention to the information in this section.  It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.  Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: Children 12 years old and under should always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big", "always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint Never allow children to slide the shoulder belt behind them or under their arm.  You should read the instructions provided with your child restraint to make sure that you are using it properly.  All occupants should always wear their lap and shoulder belts properly.  The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate.  Do not lean against the door or window.  If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and", "occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.  If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see \"\u21e8if you need assistance\" for customer service contact information.  WARNING: Never place a rear-facing child restraint in front of an air bag.  A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.  Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing child restraint in the rear seat.  If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle.  Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.", "the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to", "will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Hazard Warning Flashers Button The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the", "or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Warning CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks 1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Button  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Hazard Warning Flashers Button With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit", "the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.  turn on the Hazard Warning Flashers.  Apply the parking brake firmly and shift an automatic transmission in PARK; a manual transmission to REVERSE.  Block the wheel diagonally opposite the wheel to be raised.  Never start or run the engine with the vehicle on a jack.  Do not let anyone sit in the vehicle when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get", "when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.  Only use the jack in the positions indicated and for lifting this vehicle during a tire change.  If working on or near a roadway, be extremely careful of motor traffic.  To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.", "Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose", "the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.", "and power steering, and fill as needed.  Check function of all interior and exterior lights.  PARKING BRAKE Before exiting the vehicle, make sure that the parking brake is fully applied.  Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or FIRST gear.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to", "selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  WARNING: Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  CAUTION: If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  See the following steps to use", "Have the brake system serviced by an authorized dealer immediately.  See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle", "Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and", "it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear", "the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Start by removing the rear window first.  Use the two straps located on the bottom of each", "Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the", "the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Guide the top of the quarter panel cover assembly up into the retainer.  Step One Failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the Soft Top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step Two It is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step Three From either side, guide the rear window into the retainer while keeping the window level.  Step Four Engage the retainer along the bottom of the rear", "while keeping the window level.  Step Four Engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step Five Engage the vertical retainers up the right and left side of the rear window.  Step Six Tuck the rear window under the soft top fabric and press firmly.  Step Seven Engage the rear window retainers in the lower right and left corners.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step Two 1 \u2014 Outside Panel Lock 2 \u2014 Rear Panel Lock 3 \u2014 Front Panel Lock Unlatch the left side header panel latch located at the top of the windshield.  Step Three Remove the left side panel.  Repeat the preceding steps to remove the right side panel.", "Do not use abrasive cleaning components, solvents, steel wool, or other aggressive material to clean the lenses.  The lenses in front of the instruments in this vehicle are molded in clear plastic.  When cleaning the lenses, care must be taken to avoid scratching the plastic.  Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsTo minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.  To remove road", "of scratching the lenses and reducing light output, avoid wiping with a dry cloth.  To remove road dirt, wash with a mild soap solution followed by rinsing.  If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  If the \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the windshield and forward-facing camera inspected at an authorized dealer.  All glass surfaces should be cleaned on a regular basis with Mopar\u00ae Glass Cleaner, or any commercial household-type glass cleaner.  Never use an abrasive type cleaner.  Use caution when cleaning the inside rear window equipped with electric defrosters or windows equipped", "caution when cleaning the inside rear window equipped with electric defrosters or windows equipped with radio antennas.  Do not use scrapers or other sharp instruments that may scratch the elements.  The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems are experienced.  This inspection should include the following points:  Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic.  When cleaning the lenses, care must be taken to avoid scratching the plastic.  Clean with a wet soft cloth.  A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.  If soap is used, wipe clean with a clean damp cloth.  Dry with a soft cloth.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the", "required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash", "with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.", "If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all", "the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low", "It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and", "injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can", "windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold", "the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervalsYour vehicle is equipped with dual hydraulic brake systems.  If either of the two hydraulic systems lose normal capability, the remaining system will still function.  However, there will be some loss of overall braking effectiveness.  You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.  If the driver does not take action based upon these progressive warnings, then the system will provide a limited level of active braking to help slow the vehicle and mitigate the potential forward collision.  If the driver reacts to the warnings by braking and the system determines that the driver intends to avoid the collision by braking but has not applied sufficient brake force, the system will compensate and provide additional brake force as required.  The BAS is designed to", "the system will compensate and provide additional brake force as required.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting", "afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user's safety or the safety of others.  Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The ACC system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped", "system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems.  If either of the two hydraulic systems lose normal capability, the remaining system will still function.  However, there will be some loss of overall braking effectiveness.  You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.  In the event power assist is lost", "or stop, and potential activation of the Brake Warning Light.  In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function.  However, the effort required to brake the vehicle will be much greater than that required with the power system operating.  Brake System In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervals WARNING: Riding the brakes can lead to brake failure and possibly a collision.  Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.  You would not have your full braking capacity in an emergency.  Brake Assist System (BAS) The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and", "detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  WARNING: The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous", "The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user's safety or the safety of others.  Brake System In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervals WARNING: Riding the brakes can lead to brake failure and possibly a collision.  Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.  You would not have your full braking capacity in an emergency.", "Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWRWARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do", "and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.", "If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for serviceIn unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature", "whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the", "procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an", "reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain", "for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Note: depending on the vehicle\u2019s options, feature settings may vary.  Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and", "off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.", "frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still", "the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.", "Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  When the Display button is pressed on the touchscreen, the system will display the options related to the theme (if equipped), brightness, and color of the touchscreen.  The available settings are: note: depending on the vehicle\u2019s options, feature settings may vary.  MAX A/C Button", "settings are: note: depending on the vehicle\u2019s options, feature settings may vary.  MAX A/C Button Press and release the MAX A/C button on the touchscreen to change the current setting to the coldest output of air.  MAX A/C sets the control for maximum cooling performance.  The MAX A/C indicator illuminates when MAX A/C is on.  Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.  Note: The MAX A/C button is only available on the touchscreen.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c", "if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.", "In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this", "to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeHow long does it take to remotely start my vehicle?  Depending on various conditions, it can take three minutes or more for the request to get", "vehicle?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will remote start your vehicle more quickly.  However its range is limited.  For example, when you are leaving the stadium after the game, you can use the Vehicle Branded App to remote start your vehicle and have the inside of your vehicle comfortable by the time you get to it.  Will my vehicle be safe if I lose my wireless device?  People sometimes lose their wireless devices, which is why security measures have been engineered into the Vehicle Branded App.  Asking for your username, password and SiriusXM Guardian\u2122 Security PIN help to ensure that nobody can start your vehicle if they happen to find your device.  Can someone drive off with my vehicle using the App?  nob Driving your vehicle still requires the keys to be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the", "be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the interior before you arrive.  Can I stop a vehicle that is being driven with the cancel Remote Vehicle Start command?  nob If the vehicle is in motion, the cancel Remote Vehicle Start button will not stop the vehicle.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal", "Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.", "Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and", "it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear", "the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Start by removing the rear window first.  Use the two straps located on the bottom of each", "Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the", "the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Guide the top of the quarter panel cover assembly up into the retainer.  Step One Failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the Soft Top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step Two It is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step Three From either side, guide the rear window into the retainer while keeping the window level.  Step Four Engage the retainer along the bottom of the rear", "while keeping the window level.  Step Four Engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step Five Engage the vertical retainers up the right and left side of the rear window.  Step Six Tuck the rear window under the soft top fabric and press firmly.  Step Seven Engage the rear window retainers in the lower right and left corners.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step Two 1 \u2014 Outside Panel Lock 2 \u2014 Rear Panel Lock 3 \u2014 Front Panel Lock Unlatch the left side header panel latch located at the top of the windshield.  Step Three Remove the left side panel.  Repeat the preceding steps to remove the right side panel.", "Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the", "start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: The message will stay active until the ignition is placed in the ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP", "ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  To insert an Auxiliary device, gently insert the Auxiliary device cable into the AUX port.  If you insert an Auxiliary device with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system", "with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is", "which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on", "obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Different colored zones indicate the distance to the rear of the vehicle.  The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.", "speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously", "speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  Manual Activation Of The Rear View Camera  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will", "view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in", "pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical", "in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the", "connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these", "in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.  Note: Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle while making connections.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack,", "alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two", "Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and", "Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have", "discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.", "See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you", "See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking", "engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch", "and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center", "Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  This mirror automatically adjusts for headlight glare", "cupholders, and front door handles).  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.", "ParkSense Sensors The four ParkSense sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 79 inches (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.  The six ParkSense sensors, located in the front fascia/bumper, monitor the area in front of the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 47 inches (120 cm) from the front fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.  The ParkSense Park Assist system provides visual and audible indications of the distance between the rear and/or front fascia/bumper and a detected obstacle when backing up or moving forward (e.g.  during a parking maneuver).  For system limitations and usage precautions, see", "forward (e.g.  during a parking maneuver).  For system limitations and usage precautions, see ParkSense will turn off the Front Park Assist audible alert (chime) after approximately three seconds when an obstacle has been detected, the vehicle is stationary, and the brake pedal is applied.  ParkSense can be active only when the gear selector is in REVERSE or DRIVE.  If ParkSense is enabled at one of these gear selector positions, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above.  A warning will appear in the instrument cluster display indicating the vehicle is above ParkSense operating speed.  The system will become active again if the vehicle speed is decreased to less than approximately 6 mph (9 km/h).  The ParkSense Warning screen is located within the instrument cluster display It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.  ParkSense is only a parking aid", "and/or front fascia/bumper and the detected obstacle.  ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles.  Parking curbs might be temporarily detected or not detected at all.  Obstacles located above or below the sensors will not be detected when they are in close proximity.  The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected.  It is recommended that the driver looks over his/her shoulder when using ParkSense.  Setting Name Description Forward Collision Warning Sensitivity This setting will change the distance at which the Forward Collision Warning (FCW) alert sounds.  The \u201cMedium\u201d setting will have the FCW system signal when an object is in view, and the possibility of a collision is detected.  The \u201cNear\u201d setting will have the FCW system signal when the object is closer to the vehicle.  The \u201cFar\u201d setting will have the FCW system signal when an object is at a far distance from the", "The \u201cFar\u201d setting will have the FCW system signal when an object is at a far distance from the vehicle.  Forward Collision Warning This setting will turn the Forward Collision Warning system on or off.  The \u201cOff\u201d setting will deactivate the FCW system.  The \u201cWarning Only\u201d setting will provide only an audible chime when a collision is detected.  The \u201cWarning + Active Braking\u201d setting will provide an audible chime and apply some brake pressure when a collision is detected.  ParkSense This setting will change the type of ParkSense alert when a close object is detected and can provide both an audible chime and a visual display when an object is detected.  Front ParkSense Volume This setting adjusts the volume of the Front ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Rear ParkSense Volume This setting adjusts the volume of the Rear ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Blind Spot Alert This setting will change the type of alert provided when an", "\u201cMedium\u201d, and \u201cHigh\u201d.  Blind Spot Alert This setting will change the type of alert provided when an object is detected in a vehicle\u2019s blind spot.  The \u201cOff\u201d setting will turn off Blind Spot Alert.  The \u201cLights\u201d setting will activate the Blind Spot Alert lights on the outside mirrors.  The \u201cLights & Chime\u201d setting will activate both the lights on the outside mirrors and an audible chime.  Hill Start Assist This setting will turn the Hill Start Assist system on or off.  ParkView Backup Camera Active Guidelines This setting will turn the ParkView Backup Camera Active Guidelines on or off.  ParkView Backup Camera Delay This setting will add a timed delay to the ParkView Backup Camera when shifting out of REVERSE.  Fixed ParkView Backup Camera Guidelines This setting will turn the Fixed ParkView Backup Camera Guidelines on or off.  Front Camera Gridlines This setting will turn the Front Camera Gridlines on or off.  Tire Fill Assist This setting will turn Tire Fill Assist on or off.  ParkSense Warning Display The", "Tire Fill Assist This setting will turn Tire Fill Assist on or off.  ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster displayIt provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.", "When To Use 4L Range When off-road driving, shift into 4L for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low speed pulling power.  This range should be limited to extreme situations such as deep snow, mud, steep inclines, or sand where additional low speed pulling power is needed.  Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4L range.  CAUTION: Do not use 4L range when operating the vehicle on dry pavement.  Driveline hardware damage can result.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street", "in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument", "to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the", "provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the", "4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.", "Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the", "the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact.  Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.  This feature notifies the user when the placard tire pressure is attained while inflating or deflating the tire.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof", "to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  The functions described are for when the Jeep\u00ae wireless speaker is undocked from the vehicle.  When plugged into the docking station, the Jeep\u00ae wireless speaker functions as part of the vehicle\u2019s sound system.  The Jeep\u00ae wireless speaker is IP67 waterproof certified with design in mind to withstand rainfall, waterjets, splashing and being submerged in up to 3 ft (1 m) of water for up to 30 minutes.", "When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  Avoid", "Before getting out of the vehicle, be sure to check that there is no one left inside.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Child-Protection Door Lock System \u2014 Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove the sealing plug for access, and use a flat-blade screwdriver (or mechanical key) to rotate the dial to the lock or unlock position.  Note: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection", "the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Note: Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  When the Child-Protection Door Lock system is engaged, the door can be", "is no one left inside.  When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Child-Protection Door Lock Location", "Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app", "available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a", "plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Apps The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear", "Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular", "you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Description SmartWatch Integration puts the Vehicle Branded App right on your", "on the touchscreen.  Description SmartWatch Integration puts the Vehicle Branded App right on your Apple\u00ae Watch or Android\u2122 Wear.  To get started, follow these steps: Download the Vehicle Branded App from the App Store\u00ae or Google Play.  Log onto the app from your smartphone using the username and password you created when you first set up your account.  Make sure your watch and smartphone are connected through Bluetooth\u00ae.  The Vehicle Branded App should appear on your SmartWatch.  Once the app is downloaded on your SmartWatch, you can enjoy these features: Lock or unlock your vehicle by tapping the remote lock button in the app and entering your security PIN.  Remote start or stop your vehicle.  View important vehicle stats, such as fuel level, vehicle location, tire pressure warning, and more.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was", "smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into", "the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your", "data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or", "The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 \u00b9 use this qr code to access your digital experience.  While using Android Auto\u2122, Google Maps\u2122 provides voice-guided:", "Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact", "background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected,", "will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands", "using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait", "while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice", "natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the", "vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure", "it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always", "inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children", "in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on", "or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the", "location accessible to children.  A child could operate power windows, other controls, or move the vehicle.", "Off-Road Driving Tips  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled", "you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface", "should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?", "Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too", "gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat,", "the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating,", "off immediately and call for service.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as", "the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take", "the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the", "system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service", "Before You Cross Any Type Of Water As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the", "through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if", "ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current", "you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.  Crossing Puddles, Pools, Flooded Areas Or Other Standing Water Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it", "contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.  CAUTION: Muddy waters can reduce the cooling system effectiveness by depositing debris onto the radiator.  Driving Through Water Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing", "to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  CAUTION: Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be", "cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water Flowing water can be extremely dangerous.  Never attempt to cross a fast running stream or river even in shallow water.  Fast moving water can easily push your vehicle downstream, sweeping it out of control.  Even in very shallow water, a high current can still wash the dirt out from around your tires putting you and your vehicle in jeopardy.  There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the vehicle's running ground clearance.  You should never attempt to cross flowing water which is deeper than", "running ground clearance.  You should never attempt to cross flowing water which is deeper than the vehicle's running ground clearance.  Even the slowest current can push the heaviest vehicle downstream and out of control if the water is deep enough to push on the large surface area of the vehicle's body.  Before you proceed, determine the speed of the current, the water's depth, approach angle, bottom condition and if there are any obstacles.  Then cross at an angle heading slightly upstream using the low and slow technique.  WARNING: Never drive through fast moving deep water.  It can push your vehicle downstream, sweeping it out of control.  This could put you and your passengers at risk of injury or drowning.", "Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not", "had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  For normal service, periodic fluid level checks are not required.  When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected.  If gear oil leakage is suspected, inspect the fluid level.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within", "will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Intentional tampering with emissions control systems can result in civil penalties being assessed against you.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery", "not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m", "This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  EMISSIONS", "The I/M station can fail your vehicle because the MIL is on with the engine running.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not", "is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently", "is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button", "and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.", "Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a", "electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access,", "may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will", "and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to", "your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual", "increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.", "and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics", "All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48", "and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The", "vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This indicator light will illuminate for approximately two seconds when the ignition is turned to the ON/RUN position.  Its duration may be longer based on colder operating conditions.  Vehicle will not initiate start until telltale is no longer displayed.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in", "Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The message will stay active until the ignition is placed in the ON/RUN position.  Anti-Lock Brake System (ABS) Warning Light This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.", "in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The warning display will turn on indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The Air Bag Warning Light will turn on", "you if the light comes on again after initial startup.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  This warning light will illuminate when the Stop/Start system is not functioning properly and service is required.  Contact an authorized dealer for service.  This warning light monitors the ABS.  The light will turn on when the ignition is", "for service.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC", "Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.", "WARNING LIGHTS AND MESSAGES The warning/indicator lights will illuminate in the instrument panel together with a dedicated message and/or acoustic signal when applicable.  These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner\u2019s Manual, which you are advised to read carefully in all cases.  Always refer to the information in this chapter in the event of a failure indication.  All active telltales will display first if applicable.  The system check menu may appear different based upon equipment options and current vehicle status.  Some telltales are optional and may not appear.  Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which", "Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  Upper Center None Time Current Econ Compass Range to Empty Trip A Distance Audio Average Econ Trip B Distance Outside Temp Menu Title Speedometer Adjustable Upper Anchorage If the compression is increased too much on the front upper corner of the rear doors, deformation of the seal will occur.", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Apple CarPlay\u00ae.  Anywhere using your mobile device and Vehicle Branded App From your computer on the Owner\u2019s Site (not available on all functions) Contacting SiriusXM Guardian\u2122 Customer Care (not available on all functions) Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.", "function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control", "the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.", "and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  Android Auto\u2122", "command your vehicle.  Other operating systems may be supported in the future.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your", "You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Android Auto\u2122 allows you to access and stream your favorite music with apps like YouTube Music, iHeartRadio, and Spotify.  Using your smartphone\u2019s data plan, you can stream endless music on the road.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your", "its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be", "in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  While using Android Auto\u2122, Google Maps\u2122 provides voice-guided: Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used", "organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is", "to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.", "If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offIf the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and", "steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate", "Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  This warning light will turn on when there's a fault with the EPS system The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which", "instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offThe heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on", "only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Press the heated", "Light is illuminated, you could cause the clutch to overheat and cause a fire.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  When the SET (+) or the SET (-) button (located on the steering wheel) is pushed, the display will read \u201cACC SET.\u201d The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which", "instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d This warning light will turn on when there's a fault with the EPS system When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds,", "Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  Push the SWAY BAR switch to disconnect or connect the sway bar.  The Sway Bar Indicator Light (located in the instrument cluster) will illuminate when the bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when activation conditions are not met.  The stabilizer/sway bar", "during activation transition, or when activation conditions are not met.  The stabilizer/sway bar should remain in on-road mode during normal driving conditions.  The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.  If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.", "Materials Added To Fuel Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Designated TOP TIER Detergent Gasoline contains a higher level of detergents to further aide in minimizing engine and fuel system deposits.  When available, the usage of TOP TIER Detergent Gasoline is recommended.  Visit www.toptiergas.com for a list of top tier detergent gasoline retailers.  Indiscriminate use of fuel system cleaning agents should be avoided.  Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients.  These can harm fuel system gasket and diaphragm materials.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are", "gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels", "standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility", "performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  Methylcyclopentadienyl Manganese Tricarbonyl (MMT) In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasolines to increase octane.  Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT.  Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles.  The manufacturer recommends that gasoline without MMT be used in your vehicle.  The MMT content of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gasoline retailer whether the gasoline contains MMT.  MMT is prohibited in Federal law and California reformulated gasoline.", "UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch", "on the Uconnect system.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays", "When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Depending on the vehicle\u2019s options, feature settings may vary.  Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Depending on the vehicle\u2019s options, feature settings may vary.", "Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking", "engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the", "on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the", "interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy", "switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.", "This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48", "and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The", "vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This indicator light will illuminate for approximately two seconds when the ignition is turned to the ON/RUN position.  Its duration may be longer based on colder operating conditions.  Vehicle will not initiate start until telltale is no longer displayed.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in", "Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The message will stay active until the ignition is placed in the ON/RUN position.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the", "the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Seat Belt Reminder Warning Light This warning light indicates when the driver or passenger seat belt is unbuckled.  When the ignition is first placed in the ON/RUN or ACC/ON/RUN position and if the driver\u2019s seat belt is unbuckled, a chime will sound and the light will turn on.  When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound Service 4WD Warning Light \u2014 If Equipped This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it", "to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.", "Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts", "Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow", "the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down", "nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.", "the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive", "the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose", "If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.", "Green Indicator Lights 4WD Auto Indicator Light \"\u21e84WD Auto Indicator Light \u2014 If Equipped\" Front Fog Indicator Light \"\u21e8Front Fog Indicator Light \u2014 If Equipped\" Parking/Headlights On Indicator Light \"\u21e8Parking/Headlights On Indicator Light\" Stop/Start Active Indicator Light \"\u21e8Stop/Start Active Indicator Light \u2014 If Equipped\" Turn Signal Indicator Lights \"\u21e8Turn Signal Indicator Lights\" Rear Seat Belt Fastened Indicator Light \"\u21e8Rear Seat Belt Fastened Indicator Light \u2014 If Equipped With A Premium Instrument Cluster\" If equipped, the overhead console contains an ASSIST and an SOS button.  Center Light Status Description Off No call activated Green Active call in progress Red System error The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  Monitoring battery level status led light red 40% or lower yellow 40% to 70% green 70% to 100% electronic stability control", "status led light red 40% or lower yellow 40% to 70% green 70% to 100% electronic stability control (esc) active warning light \u2014 if equipped this warning light will indicate when the electronic stability control system is active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is", "the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.  Adaptive Cruise Control (ACC) Set Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.  Adaptive Cruise Control (ACC) Ready Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.", "Lumbar Support The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  Lumbar Support Control Knob Turning the temperature control knob clockwise increases the heating temperature and turning the temperature control knob counterclockwise decreases the heating temperature.  Lumbar Support The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  Heater Only Turning the temperature control knob clockwise increases the heating temperature and turning the temperature control knob counterclockwise decreases the heating temperature.", "Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Drag & Drop Menu Bar The Uconnect features and services in the main menu bar are easily customized for your preference.", "The Uconnect features and services in the main menu bar are easily customized for your preference.  Simply follow these steps: press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Note: This feature is only available if the vehicle is in PARK.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the", "to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the", "select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF", "one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.", "Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque Specification For Torx Fastener Maximum Minimum 119.5 in-lb (13.5 N\u00b7m)", "specifications.  Torque Specification For Torx Fastener Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  Damage to the retainers will occur.  Step One Install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step Four Using the provided #T50 Torx head driver and ratchet, install and tighten the Torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or", "clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step Five Torque Specification For Torx Fasteners Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Step Five Before driving the vehicle with the top in the Sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners Step Six  Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the", "the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield,", "position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to", "door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The rear door frames must be removed first, followed by the front door frames.  Loosen (do not remove) the four bolts on the door hinges using the provided #T50 Torx head driver.  Hinge Bolt Locations Do not adjust the body mounted", "using the provided #T50 Torx head driver.  Hinge Bolt Locations Do not adjust the body mounted hinges, or any part of the door latch, as modifications to these parts will affect installation of the full door.  With the bolts loose, the door can be moved forward by pushing the door handle toward the front of the vehicle, and/or upward by grabbing the door handle and lifting towards the roof.  Once the gaps between the door and vehicle body are uniform around the entire door, tighten the door hinge bolts to 20.3 ft\u00b7 lb / 27.5 N\u00b7m (Max Torque: 27.3 ft\u00b7 lb / 37 N\u00b7m).  Lift upward on each section of the seat bottom.  Lift From Beneath Seat (Left Side Shown) Raise the seat bottom upward into the Stadium Position.  Stadium Position If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\"", "the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Determine which door is affected.  Open the affected door and hold a dollar-size piece of paper along the top of the door opening against the vehicle near where the leak/noise was observed.  Make sure half of the paper is above the area where the door seal contacts the door opening, while the other half is below.  Close the door on the paper, then pull the paper upward.  If the paper moves with little to no effort, the upper half-door will need to be adjusted in that area to increase seal compression.  Performing A Paper Test Push Upward On Middle Of Upper Half Door To Remove", "Rear Defrost Button Press and release the Rear Defrost Control button on the touchscreen, or push and release the button on the faceplate to turn on the rear window defroster and the heated outside mirrors (if equipped).  The Rear Defrost indicator illuminates when the rear window defroster is on.  The rear window defroster automatically turns off after 10 minutes.  CAUTION: Failure to follow these cautions can cause damage to the heating elements: Use care when washing the inside of the rear window.  Do not use abrasive window cleaners on the interior surface of the window.  Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.  Labels can be peeled off after soaking with warm water.  Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.  Keep all objects a safe distance from the window.  Heated Mirrors \u2014 If Equipped These mirrors are heated to melt frost or ice.  This feature will be activated whenever you turn on the", "mirrors are heated to melt frost or ice.  This feature will be activated whenever you turn on the rear window defroster (if equipped) \"\u21e8climate controls\" .  Winter Operation To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used.  Use of the Air Recirculation mode during Winter months is not recommended, because it may cause window fogging.", "Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash", "If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped", "and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the", "to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.", "The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and", "or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The", "to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo", "cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Hazard Warning Flashers Button The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when", "side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Warning CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks 1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If", "Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Hazard Warning Flashers Button With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not", "also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.  turn on the Hazard Warning Flashers.  Apply the parking brake firmly and shift an automatic transmission in PARK; a manual transmission to REVERSE.  Block the wheel diagonally opposite the wheel to be raised.  Never start or run the engine with the vehicle on a jack.  Do not", "opposite the wheel to be raised.  Never start or run the engine with the vehicle on a jack.  Do not let anyone sit in the vehicle when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.  Only use the jack in the positions indicated and for lifting this vehicle during a tire change.  If working on or near a roadway, be extremely careful of motor traffic.  To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.", "The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is", "an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will", "vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the", "battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as", "the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you", "a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.", "NEUTRAL (N) Use this range when the vehicle is standing for prolonged periods with the engine running.  Apply the parking brake and shift the transmission into PARK if you must exit the vehicle.  WARNING: Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.  These are unsafe practices that limit your response to changing traffic or road conditions.  You might lose control of the vehicle and have a collision.  CAUTION: Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle N (Neutral) Neutral \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicleWARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages", "without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  Five-position transfer case \u2014 if equipped the transfer case provides five positions: 2h (two-wheel drive high range) 4h auto (four-wheel drive auto high range) 4h part time (four-wheel drive part time high range) n (neutral) 4l (four-wheel drive low range) for additional information on the appropriate use of each transfer case position, see the following information:.  N (Neutral) Neutral \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicleWARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position", "or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  Neutral indicator light \u2014 if equipped this light alerts the driver that the vehicle is in the neutral mode \"\u21e8automatic transmission \u2014 if equipped\" .", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to", "this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before", "it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your", "flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.", "N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.  See Recreational Towing for further information WARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll,", "both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) NEUTRAL (N)  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.", "Apple CarPlay\u00ae Voice Command Apple CarPlay\u00ae allows you to use your voice to interact with Siri through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your iPhone\u00ae and a number of its apps onto your Uconnect touchscreen.  Connect your iPhone\u00ae 5 or higher to one of the media USB ports, using the factory-provided Lightning cable, and press the new Apple CarPlay\u00ae icon that replaces your Phone icon on the main menu bar to begin Apple CarPlay\u00ae.  Push and hold the vr button on the steering wheel, or press and hold the home button within apple carplay\u00ae, to activate siri, which recognizes natural voice commands to use a list of your iphone\u00ae features: phone music messages maps \u2014 if equipped additional apps \u2014 if equipped note: feature availability depends on your carrier and mobile phone maker.  Some Apple CarPlay\u00ae features may not be available in every region and/or language.  Note: Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered", "Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered in the US and other countries.  Apple\u00ae terms of use and privacy statements apply.  Apple carplay\u00ae apple carplay\u00ae \u00b9 use this qr code to access your digital experience.  Uconnect works seamlessly with Apple CarPlay\u00ae, the smarter, more secure way to use your iPhone\u00ae in the car, and stay focused on the road.  Use your Uconnect Touchscreen display, the vehicle's knobs and controls, and your voice with Siri to get access to Apple Music\u00ae, Maps, Messages, and more.  To use Apple CarPlay\u00ae, make sure you are using iPhone\u00ae 5 or later, have Siri enabled in Settings, ensure your iPhone\u00ae is unlocked for the very first connection only, and then use the following procedure: Connect your iPhone\u00ae to one of the media USB ports in your vehicle.  Note: be sure to use the factory-provided lightning cable that came with your phone, as aftermarket cables may not work.  Once the device is connected and recognized, the Phone icon on the", "cables may not work.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Apple CarPlay\u00ae Icon.  Note: apple carplay\u00ae is set to launch immediately.  You can also launch it by pressing the Apple CarPlay\u00ae icon on the touchscreen.  Apple carplay\u00ae and lte data coverage 1 \u2014 lte data coverage 2 \u2014 apple carplay\u00ae icon once apple carplay\u00ae is up and running on your uconnect system, the following features can be utilized using your iphone\u00ae data plan: phone music messages maps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Apple CarPlay\u00ae features may or may not be available in every region and/or language.  Note: To use Apple CarPlay\u00ae, make sure that cellular data is turned on, and that you are in an area with cellular coverage.  Your data and cellular coverage is shown on the left side of the radio screen.  Data plan rates apply.  Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Apple CarPlay\u00ae.  Anywhere using your mobile device and Vehicle Branded App From your computer on the Owner\u2019s Site (not available on all functions) Contacting SiriusXM Guardian\u2122 Customer Care (not available on all functions) Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.", "function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Closing The Hood To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.", "rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  WARNING: Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.", "The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d  The obd ii system may not be ready if your vehicle was", "Diagnostic System (OBD II) Cybersecurity\u201d  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully", "Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  ONLY an authorized service technician should connect equipment", "that the system is now ready.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.", "The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the", "is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine", "To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the", "of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going", "it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.", "Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Vehicle must be at a stop and the gear selector", "windshield is raised prior to installing the tops.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Release both of the outside hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  1 \u2014 Pull For Windshield Washer 2 \u2014 Rotate For Wiper Operation 3 \u2014 Push Up For Mist The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.", "can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.  FOLDING WINDSHIELD The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element provides.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Raise", "low range operation preferred if you are driving off-road with the windshield folded down.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  WARNING: Carefully follow these warnings to help protect against personal injury: Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from", "before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshieldUsing the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.", "the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Cleaning Instructions During windshield down applications, dust/dirt can accumulate in the cover and block the camera lens.  Use a microfiber cloth to clean the camera lens, module, and inside cover, being careful not to damage or scratch the module.", "Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  If you get hung up or high-centered on an object,", "jacking on locations other than those indicated.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.", "get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand,", "brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Preparations For Jacking Park on a firm, level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side", "level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  Turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers should not remain in the vehicle when the vehicle is being jacked in position.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn", "alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals:", "the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.", "indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this", "oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Secondary Method For Oil Change Reset Procedure Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Note: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.  If necessary, repeat this procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take", "change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the", "necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.", "Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may", "the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure", "30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are", "pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  If you store quantities of fuel, good maintenance of the stored fuel is also", "injury or death.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster", "ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void", "from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop", "due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If", "system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  Based on engine operation conditions, the oil change", "possible, within the next 500 miles (805 km).  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  Use only the manufacturer\u2019s recommended fluid For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type", "seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  See Engine Fluids and Lubricants for the correct engine oil viscositySynthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Lubricant should be approximately 1/8 inch (3 mm) below the bottom edge of the oil fill hole.  Use only the manufacturer\u2019s recommended fluid Trac-Lok is especially helpful during slippery driving conditions.  With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction.  Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure build-up or your tire pressure will be too low.  1 \u2014", "operation.  DO NOT reduce this normal pressure build-up or your tire pressure will be too low.  1 \u2014 Coolant Temperature 2 \u2014 Oil Temperature 3 \u2014 Battery Voltage 4 \u2014 Transmission Temperature 5 \u2014 Oil Pressure Operation in ambient temperature below 32\u00b0F (0\u00b0C) may require special considerations.  The following charts suggest these options:", "Description Family Drive Alerts help promote safer driving and give you peace of mind when your loved ones are out on the road.  You can set boundary limits, monitor driving speed, and pinpoint your vehicle\u2019s location any time, any place.  Use the vehicle branded app to set alerts: boundary alert receive a notification the moment your vehicle is driven either out of or into a geographic boundary that you set.  Curfew alert receive a notification when your car is being driven outside of the curfew time.  Speed alert receive a notification whenever your car exceeds a speed limit you set.  Valet alert receive a notification if and when your vehicle is driven outside a quarter-mile radius of a valet drop-off zone.  Event Data Recorder (EDR) This vehicle is equipped with an event data recorder (EDR).  The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle\u2019s systems", "or hitting a road obstacle, data that will assist in understanding how a vehicle\u2019s systems performed.  The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.  The edr in this vehicle is designed to record such data as: how various systems in your vehicle were operating; whether or not the driver and passenger safety belts were buckled/fastened; how far (if at all) the driver was pressing the accelerator and/or brake pedal; and, how fast the vehicle was traveling.  These data can help provide a better understanding of the circumstances in which crashes and injuries occur.  To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed.  In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.  Note: EDR data are recorded by your vehicle only if a", "they have access to the vehicle or the EDR.  Note: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are recorded.  However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full", "drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.", "When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.", "jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or", "with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash", "other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.", "connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the", "post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.", "Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Drag & Drop Menu Bar The Uconnect features and services in the main menu bar are easily customized for your preference.", "The Uconnect features and services in the main menu bar are easily customized for your preference.  Simply follow these steps: press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Note: This feature is only available if the vehicle is in PARK.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the", "to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the", "select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF", "one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.", "Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.  Do not open or close the Sunrider\u00ae top while driving.  Operating the top while driving could cause the driver to lose", "the Sunrider\u00ae top while driving.  Operating the top while driving could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.  Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the", "driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.  Safety Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.  WARNING: Improperly inflated tires are dangerous and can cause collisions.  Underinflation increases tire flexing and can result in overheating and tire failure.  Overinflation reduces a tire's ability to cushion shock.  Objects on the road and chuckholes can cause damage that result in tire failure.  Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.  Unequal tire pressures can cause steering problems.  You could lose control of your vehicle.  Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.  Always drive with each tire", "to the other can cause the vehicle to drift to the right or left.  Always drive with each tire inflated to the recommended cold tire inflation pressure.  Note: Unequal tire pressures from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure from side to side may cause the vehicle to drift left or right.  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  Manual Mirror Adjustment If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  This feature allows you to tilt the steering column upward or", "or removal of an obstruction.  This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Ignoring the Rearview Mirror light could mean you will not have SOS Call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  When the vehicle is started,", "dealer service the Occupant Restraint Control system immediately.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  When cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on the mirror.", "ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemApple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is", "while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Depending on your vehicle\u2019s specifications, the USB port may contain playback capabilities and will allow you to play music from your smartphone device or USB devices through your vehicle\u2019s sound system.  1 \u2014 Reset Button 2 \u2014 Battery Status Button 3 \u2014 Service/Diagnostic Port (Non-charging, Non-customer use port) 4 \u2014 Type A USB Charging Port 5 \u2014 Battery Status LED 6 \u2014 Speaker Charging Port 7 \u2014 AUX Port The Smart Charging USB ports provide power to your device up to an hour after the vehicle is turned off.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and", "may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your", "technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.", "Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking", "engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch", "and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center", "Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Dimmer Control The dimmer control is part of the", "illuminated cupholders, and front door handles).  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).", "Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers", "to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to", "may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.", "The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  Do Not Use Mechanical Key  Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.  Your vehicle is", "comes as an assembly, and is not removable.  This can damage the silicone shield.  Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic", "subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be", "Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When", "if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so", "in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being", "be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx", "the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a", "electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access,", "may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will", "and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key", "unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the", "floor are removed.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Console Storage Compartment The center console has both an", "the bin to the floor are removed.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove", "Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Locking Storage Bin (Closed View) Locking Storage Bin", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive", "are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.", "If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature", "whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  If the vehicle is overheating, it will need to be serviced by an authorized dealer.  If the light turns on while driving, safely pull", "will need to be serviced by an authorized dealer.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for serviceIn unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating", "four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  Do not open hot engine cooling system.", "pedal and repeat the \u201cNormal Starting\u201d procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If", "headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this", "engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure.  This could damage your engine.  Engine misfiring or vibrating severely Sudden loss of power Unusual engine noises Fuel, oil or coolant leaks Sudden change, outside the normal operating range, in the engine operating temperature Excessive smoke Oil pressure drop If there is a malfunction in the Stop/Start system, the system will not shut down the", "pressure drop If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display", "Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  Engine start-up in very low ambient temperature", "time.  Wait 10 to 15 seconds before trying again.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant", "a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.", "Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center", "or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside", "of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument", "the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup", "cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside", "ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all", "preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls,", "Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a", "brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using", "stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the", "or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the", "form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background", "for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold", "cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by", "the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Get started the", "have incoming text messages read out loud, and place and receive hands-free calls.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.", "Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not", "Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed", "system going into a stop/start ready state under more extreme conditions of the items listed previously.  Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.", "Jack Location The jack and tools are stored under the right rear seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat.  Removing the wing bolt release the tool bag straps from the jack and remove tools from bag.  Jack and tool bag remove tool kit and assemble tools.  Jack And Tool Bag There are two ways to assemble the tools: Note: If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  CAUTION: The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools,", "and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools, always reinstall them in the original carrier and location.  While driving you may experience abrupt stopping, rapid acceleration or sharp turns.  A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an", "being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Gasoline instrument clusters gasoline instrument clusters \u00b9 use this qr code to access your digital experience.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the", "moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  WARRANTY INFORMATION See the Warranty Information for the terms and provisions of FCA US LLC warranties applicable to this vehicle and market.  Refer to www.mopar.com/om for further information.  See the Warranty Information for the terms and provisions of FCA Canada Inc. warranties applicable to", "the Warranty Information for the terms and provisions of FCA Canada Inc. warranties applicable to this vehicle and market.  Refer to www.owners.mopar.ca/en for further information.  Use this QR code to access your digital experience.", "If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  To close the tailgate, lift upward until both sides latch into place.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Tailgate In Mid Position If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable", "If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To use the mid position, open the tailgate and lower it to near mid position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  The tailgate is dampened to provide a slower, more controlled lowering.  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the", "If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.", "What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage", "check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any", "hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision", "applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is", "it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Hazard Warning Flashers Button The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF", "the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Warning CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut", "CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks 1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button", "If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is", "center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator,", "After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough", "not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is", "an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed", "Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the", "you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or", "with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of", "and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match", "Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl", "or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  To ensure proper engine lubrication, the engine oil must be maintained at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Check engine oil level Check windshield washer fluid level Check the tire pressures and look for unusual wear or", "oil level Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage Check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed Check function of all interior and exterior lights  Fluid Level Check Check the fluid level by removing the fill plug.  The fluid level should be between the bottom of the fill hole and a point not more than 3/16 of an inch (4.76 mm) below the bottom of the hole.  Add fluid, if necessary, to maintain the proper level.", "Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the", "code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire full size spare \u2014 if equipped the full size spare is for temporary emergency use only.  This tire may look like", "\u2014 if equipped the full size spare is for temporary emergency use only.  This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not.  This spare tire may have limited tread life.  When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced.  Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity.  Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Rim Size This is the rim size that is appropriate for the tire size listed.  Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h,", "capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the", "to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire.", "Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  Do Not Use Mechanical Key  Key Fob Your vehicle is", "compartments (if equipped), and rear seatbacks.  Do Not Use Mechanical Key  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be", "may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .", "To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries", "system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster", "in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.", "active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely", "in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "The warning display will turn on indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN", "on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  This warning light will illuminate when the Stop/Start system is not functioning properly and service is required.  Contact an authorized dealer for service.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The", "is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has", "ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use", "to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The red Brake System Warning Light will turn on when", "and may stay on for as long as four seconds.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  This warning light will", "dealer as soon as possible to have the problem diagnosed and corrected.  This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however,", "If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This indicator light will illuminate for approximately two seconds when the ignition is turned to the ON/RUN position.  Its duration may be longer based on colder operating conditions.  Vehicle will not initiate start until telltale is no longer displayed.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning", "The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The message will stay active until the ignition is placed in the ON/RUN position.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Preparations For Jacking Park on a firm, level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking", "operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers should not remain in the vehicle when the vehicle is being jacked in position.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating", "not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.", "When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  After fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged.  If the system detects a malfunction, the \u201cgASCAP\u201d message will display in the odometer display.  Tighten the gas cap until a \"clicking\" sound is heard.  This is an indication that the gas cap is properly tightened.  Push the odometer reset button to turn the message off.  If the problem persists, the message will appear the next time the vehicle is started.  This might indicate a damaged cap.  If the problem is detected twice in a row, the system will turn on the MIL.  Resolving the problem will turn the MIL off.  The fuel", "in a row, the system will turn on the MIL.  Resolving the problem will turn the MIL off.  The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Fuel System Messages The following chart contains a list of different messages that may appear in the instrument cluster, depending on different system or fuel conditions.  Use the descriptions to interpret what the message means and determine the best action to take.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it", "the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d This warning light will turn on when there's a fault with the EPS system When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive", "Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  Push the SWAY BAR switch to disconnect or connect the sway bar.  The Sway Bar Indicator Light (located in the instrument cluster) will illuminate when the bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when", "bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when activation conditions are not met.  The stabilizer/sway bar should remain in on-road mode during normal driving conditions.  The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.  If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.", "Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  Bumper end caps are removable on steel bumpers only.  The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 Bolt #2 Remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Before completing the following steps: if your vehicle", "Repeat this procedure on the other side.  Before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step Two 1 \u2014 Hex Bolt Cover Installed 2 \u2014 Hex Bolt Cover Removed Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting", "trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step Six Secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Do Not Overtighten!  Damage to the windshield could result.  Open the fuel filler door.  Fuel Filler Door Remove the fuel cap by rotating it counterclockwise.  Fuel Filler Cap Fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  Lowering the windshield before", "gasoline nozzle, reinstall fuel cap and close the fuel filler door.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx", "the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to", "(two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the", "the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.", "Soft Top Rear Window Storage Bag \u2014 If Equipped To safely store the soft top rear window, proceed as follows: With the bag opened completely, fold the fabric divider downward and lay the rear window in the bottom of the bag.  Step one fold the divider upward, covering the rear window.  Step two lay the first quarter panel cover assembly all the way to the right side and the second quarter panel cover assembly on the left side.  Secure both using the two hook-and-loop fastener straps on each side.  Note: the quarter panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step three 1 \u2014 left quarter panel cover assembly 2 \u2014 right quarter panel cover assembly close the storage bag and store in a safe location.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert", "latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward", "in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store", "Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal", "that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior", "header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush", "the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.", "Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet", "clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.  Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for", "front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Rear Carpet Remove the grommets under the front seat (one left and one right).  Carpet split then pull the carpet out, to the rear and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin (if equipped), by removing the four bolts that hold it to the floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and", "floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then lift the assembly out from under the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear retainers remove carpet from the vehicle.  When reinstalling the carpet, perform these steps in reverse order making sure that the carpet is tucked under the scuffs, B-pillar, console, and then refasten the grommets.  Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket", "Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS", "or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress", "the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.", "The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Retrieve funnel from under the right rear seat.  Fuel Funnel Location Refueling Funnel Remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting Funnel Ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from", "an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel", "the clutch to overheat and cause a fire.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners", "for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not", "has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners Loosen the fasteners from the engine air cleaner filter cover using a suitable tool.  Engine Air Cleaner Filter Cover 1 \u2014 Fasteners 2 \u2014 Engine Air Cleaner Filter Cover Lift the engine air cleaner filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from the housing assembly.  engine air cleaner filter cover  The vehicle may be equipped with a refueling funnel.  Vehicles", "engine air cleaner filter cover  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  The engine may be switched off even if the warning light is on: repeated interruptions of the regeneration process could cause an early deterioration of engine oil.  For this reason it is always advisable to wait for the symbol to go off before turning off the engine, following the previously mentioned instructions.  Do not complete the DPF regeneration process when the vehicle is stopped.  See the following steps for refueling: Emergency Gas Can Refueling Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil", "periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.", "Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering", "pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode", "process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  In following situations the engine will not stop: driver\u2019s seat belt is not", "if they are fulfilled.  In following situations the engine will not stop: driver\u2019s seat belt is not buckled outside temperature is less than 10\u00b0f (\u201312\u00b0c) or greater than 109\u00b0f (43\u00b0c) actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode engine has not reached normal operating temperature battery is discharged when driving in reverse hood is open transfer case is in 4l or n (neutral) driver's seat is not occupied or driver door is open vehicle is at high altitude the vehicle is on a steep grade forward gear is engaged steering angle is beyond threshold system fault is present hvac is set to max a/c it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  To Start The Engine While In Autostop Mode When the gear selector is in NEUTRAL, the engine will start when the clutch pedal is pressed (does not require", "selector is in NEUTRAL, the engine will start when the clutch pedal is pressed (does not require complete/full pedal press).  The vehicle will go into STOP/START SYSTEM NOT READY mode until the vehicle speed is greater than 5 mph (8 km/h).  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  In following situations the engine will not stop: driver\u2019s seat belt is not buckled outside temperature is less than 10\u00b0f (\u201312\u00b0c) or greater than 109\u00b0f (43\u00b0c) actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode engine has not reached normal operating temperature battery is discharged when driving in reverse hood is open transfer case is in 4l or n (neutral) driver's seat is not occupied or driver door is open vehicle is at high altitude the vehicle is on a steep grade forward gear is engaged steering angle is beyond threshold system fault is", "is on a steep grade forward gear is engaged steering angle is beyond threshold system fault is present hvac is set to max a/c it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Possible Reasons The Engine Does", "to normal, turn the engine off immediately and call for service Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed", "(neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the", "menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING:", "display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and", "mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Rear Seat Unoccupied Indicator Light \u2014 If Equipped This light indicates when the rear passenger seats are unoccupied, and will illuminate in the upper right portion of the instrument cluster display, momentarily replacing the configurable corner information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the", "information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed", "mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the", "vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR", "clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected", "time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "Shifting Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  To engage REVERSE gear from the NEUTRAL position, lift the REVERSE ring, located below the knob and move the gear selector all the way left and then forward.  If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the", "the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  To shift the gears, fully press the clutch pedal and place the gear selector into the desired gear position (the diagram for the engagement of the gears is displayed on the handle of the selector).  The gear position will be displayed in the instrument cluster.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle", "all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If You Stall Or Begin To Lose Headway If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill", "immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If", "or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.", "AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic mode \"\u21e8automatic operation\" .  A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass,", "through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  To Deactivate A soft tap on the brake pedal, pushing the CANC (cancel) button, or normal brake pressure while slowing the vehicle will deactivate the Cruise Control without erasing the set speed from memory.  The following conditions will also deactivate the cruise control without erasing the set speed from memory: vehicle parking brake is applied stability event occurs gear selector is moved out of drive engine overspeed occurs clutch pedal is pressed (manual transmission only) vehicle is operating at a low rpm (manual transmission only) pushing the on/off button or placing the ignition", "operating at a low rpm (manual transmission only) pushing the on/off button or placing the ignition in the off position, erases the set speed from memory.  Recirculation Button Push the Recirculation button on the faceplate to change the system between recirculation mode and outside air mode.  The Recirculation indicator and the A/C indicator (if equipped) illuminate when the Recirculation button is pressed.  Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.  Recirculation can be used in all modes except for Defrost.  Recirculation may be unavailable if conditions exist that could create fogging on the inside of the windshield.  The A/C can be deselected manually without disturbing the mode control selection.  Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur.  Extended use of this mode is not recommended.  On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode", "On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode to improve window clearing operation.  Recirculation is disabled automatically if this mode is selected.  Attempting to use Recirculation while in this mode causes the LED on the control button to blink and then turn off.  A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or", "the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.", "Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical", "illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.  It may cause burns even at low temperatures, especially if used for long periods of time.  Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion.  This may cause the seat heater to overheat.  Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  The engine must be running for the heated steering wheel to operate.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle", "Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme", "HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating", "screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred,", "on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offThe heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will", "wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Press the", "Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  When the SET (+) or the SET (-) button (located on the steering wheel) is pushed, the display will read \u201cACC SET.\u201d The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.", "AUX/USB Control The Media Hub is located on the instrument panel, below the climate controls.  Behind the media hub access door, the Media Hub contains one AUX port, a Type C USB port and one standard USB port.  Both USB ports allow you to play music from smartphones or USB devices through the vehicle\u2019s sound system.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or The Smart Charging USB ports provide power to your device up to an hour after the vehicle is turned off.  For example, if a device is plugged into the Type A USB port and another device is plugged into the Type C USB port, a message will appear and allow you to select which device to use.  Located inside the center console, a second USB port allows you to only charge USB devices.  Depending on your vehicle\u2019s specifications, the USB port may contain playback capabilities and will allow you to play music from", "the USB port may contain playback capabilities and will allow you to play music from your smartphone device or USB devices through your vehicle\u2019s sound system.  A third and fourth USB port are located behind the center console, above the power inverter.  Both ports are charge only.  When a new device or smartphone is plugged into the USB ports, one of the following message will display depending on the device being utilized: \u201cA new device is now connected.  Previous connection was lost\u201d.  \u201c(Phone Name) now connected.  Previous connection was lost\u201d.  \u201cAnother device is in use through the same USB port.  Please disconnect the first device to use the second device\u201d.  Note: Once a device is connected to the USB port, it will begin charging and is ready for use with the system.  Type C and Type A charge-only USB ports can be used at the same time but cannot be used simultaneously while playing media.  When both Type C and Type A charge-only USB ports are in use they will be charged at a reduced rate.  Both ports", "C and Type A charge-only USB ports are in use they will be charged at a reduced rate.  Both ports share a single data connection.  The user cannot switch between Type A and Type C. Note: Charge unsupported devices with the Charge Only USB ports.  If an unsupported device is plugged into a Media USB port, a message will display on the touchscreen that the device is not supported by the system.  WARNING: Do not plug in or remove the external device while driving.  Failure to follow this warning could result in a collision.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service", "connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The Media Hub is located on the instrument panel, below the climate controls.  Behind the media hub access door, the Media Hub contains one AUX port, a Type C USB port and one standard USB port.  Both USB ports allow you to play music from smartphones or USB devices through the vehicle\u2019s sound system.  A third and fourth USB port are located behind the center console, above the power inverter.  Both ports are charge only.  Located inside the center console, a second USB port allows", "inverter.  Both ports are charge only.  Located inside the center console, a second USB port allows you to only charge USB devices.  AUX/USB Control The Media Hub is located on the instrument panel, below the climate controls.  Behind the media hub access door, the Media Hub contains one AUX port, a Type C USB port and one standard USB port.  Both USB ports allow you to play music from smartphones or USB devices through the vehicle\u2019s sound system.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or The Smart Charging USB ports provide power to your device up to an hour after the vehicle is turned off.  For example, if a device is plugged into the Type A USB port and another device is plugged into the Type C USB port, a message will appear and allow you to select which device to use.  Located inside the center console, a second USB port allows you to only charge USB", "device to use.  Located inside the center console, a second USB port allows you to only charge USB devices.  Depending on your vehicle\u2019s specifications, the USB port may contain playback capabilities and will allow you to play music from your smartphone device or USB devices through your vehicle\u2019s sound system.  A third and fourth USB port are located behind the center console, above the power inverter.  Both ports are charge only.  When a new device or smartphone is plugged into the USB ports, one of the following message will display depending on the device being utilized: \u201cA new device is now connected.  Previous connection was lost\u201d.  \u201c(Phone Name) now connected.  Previous connection was lost\u201d.  \u201cAnother device is in use through the same USB port.  Please disconnect the first device to use the second device\u201d.  Note: Once a device is connected to the USB port, it will begin charging and is ready for use with the system.  Type C and Type A charge-only USB ports can be used at the same time but cannot be", "the system.  Type C and Type A charge-only USB ports can be used at the same time but cannot be used simultaneously while playing media.  When both Type C and Type A charge-only USB ports are in use they will be charged at a reduced rate.  Both ports share a single data connection.  The user cannot switch between Type A and Type C. Note: Charge unsupported devices with the Charge Only USB ports.  If an unsupported device is plugged into a Media USB port, a message will display on the touchscreen that the device is not supported by the system.  WARNING: Do not plug in or remove the external device while driving.  Failure to follow this warning could result in a collision.", "Fuel Filler Cap The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Open the fuel filler door.  Fuel filler door remove the fuel cap by rotating it counterclockwise.  Fuel filler cap fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the", "is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light (MIL) to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  CAUTION: Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Note: When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure", "tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  After fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged.  If the system detects a malfunction, the \u201cgASCAP\u201d message will display in the odometer display.  Tighten the gas cap until a \"clicking\" sound is heard.  This is an indication that the gas cap is properly tightened.  Push the odometer reset button to turn the message off.  If the problem persists, the message will appear the next time the vehicle is started.  This might indicate a", "persists, the message will appear the next time the vehicle is started.  This might indicate a damaged cap.  If the problem is detected twice in a row, the system will turn on the MIL.  Resolving the problem will turn the MIL off.  The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal", "the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the", "belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure", "One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners Loosen the fasteners from the engine air cleaner filter cover using a suitable tool.  Engine Air Cleaner Filter Cover 1 \u2014 Fasteners 2 \u2014 Engine Air Cleaner Filter Cover Lift the engine air cleaner filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from the housing assembly.  engine air cleaner filter cover", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside", "are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts", "the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when", "20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set", "ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speed  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed", "show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which", "sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to", "will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Hazard Warning Flashers Button The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the", "or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Warning CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks 1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Button  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Hazard Warning Flashers Button With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit", "the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.  turn on the Hazard Warning Flashers.  Apply the parking brake firmly and shift an automatic transmission in PARK; a manual transmission to REVERSE.  Block the wheel diagonally opposite the wheel to be raised.  Never start or run the engine with the vehicle on a jack.  Do not let anyone sit in the vehicle when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get", "when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.  Only use the jack in the positions indicated and for lifting this vehicle during a tire change.  If working on or near a roadway, be extremely careful of motor traffic.  To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.", "Green Indicator Lights 4WD Auto Indicator Light \"\u21e84WD Auto Indicator Light \u2014 If Equipped\" Front Fog Indicator Light \"\u21e8Front Fog Indicator Light \u2014 If Equipped\" Parking/Headlights On Indicator Light \"\u21e8Parking/Headlights On Indicator Light\" Stop/Start Active Indicator Light \"\u21e8Stop/Start Active Indicator Light \u2014 If Equipped\" Turn Signal Indicator Lights \"\u21e8Turn Signal Indicator Lights\" Rear Seat Belt Fastened Indicator Light \"\u21e8Rear Seat Belt Fastened Indicator Light \u2014 If Equipped With A Premium Instrument Cluster\" If equipped, the overhead console contains an ASSIST and an SOS button.  Center Light Status Description Off No call activated Green Active call in progress Red System error The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  The warning display will turn on indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE", "turn on indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light", "as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  This warning light will illuminate when the Stop/Start system is not functioning properly and service is required.  Contact an authorized dealer for service.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will", "ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles", "light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  To enter the \u201cPartial Off\u201d mode, momentarily push the ESC OFF button and the ESC OFF Indicator Light will illuminate.  To turn the ESC on again, momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Automatic Headlight System will turn the headlights on or off according to ambient light levels.  To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation.  When the system is on, the headlight time delay", "the last detent for automatic headlight operation.  When the system is on, the headlight time delay feature is also on.  This means the headlights will stay on for up to 90 seconds (programmable through the uconnect settings \"\u21e8uconnect settings\" ) after you place the ignition into the off position.  To turn the automatic system off, move the headlight switch out of the AUTO position.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will", "signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Reduce power to unnecessary loads if possible: Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s exterior and interior lights.  When the \u201cDaytime Running Lights\u201d feature is selected, the daytime running lights can be turned on or off.  This feature is only allowed by law in the country of the vehicle purchase.  Depending on the vehicle\u2019s options, feature settings may vary.  Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.", "has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the", "I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.", "come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with", "in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with", "in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off", "reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper", "this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow", "can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling", "pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does", "Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.", "Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak", "a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by", "or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake", "If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light", "ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service", "comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.", "on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system", "on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt", "booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light", "to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.", "When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  All cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Remove the two screws that pass through the bed sheet metal.  Tail Lamp Screws Pull the", "(136 kg).  Remove the two screws that pass through the bed sheet metal.  Tail Lamp Screws Pull the outboard side of the lamp rearward, far enough to unsnap the two receptacles on the outboard side of the lamp housing, from the two plastic snap post retainers in the outer box side panel.  Once removed, locate and rotate the appropriate socket a quarter turn counterclockwise, then remove it from the housing.  Pull the bulb straight from the socket to replace.  To install a new bulb, reverse the procedure above.  With the bag opened completely, fold the fabric divider downward and lay the rear window in the bottom of the bag.  Step One Fold the divider upward, covering the rear window.  Step Two Lay the first quarter panel cover assembly all the way to the right side and the second quarter panel cover assembly on the left side.  Secure both using the two hook-and-loop fastener straps on each side.  The quarter panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step Three 1 \u2014", "panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step Three 1 \u2014 Left Quarter Panel Cover Assembly 2 \u2014 Right Quarter Panel Cover Assembly Close the storage bag and store in a safe location.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the", "boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover", "latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid", "the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).", "Rear Wall Storage Bin To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  Note: The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  Non-Locking Storage Wall The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  There is also an option to remove the wall by removing the four bolts that connect the storage wall to the floor.  Rear Wall Storage Bin To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  Note: The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of", "secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  Rear Wall Storage Bin The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.", "Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light", "Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  The red Brake System Warning Light will", "ON/RUN mode, have the light repaired as soon as possible.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer", "a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  This warning light will turn on when there's a fault with the EPS system  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning", "If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and", "to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a", "of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.", "Materials Added To Fuel Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Designated TOP TIER Detergent Gasoline contains a higher level of detergents to further aide in minimizing engine and fuel system deposits.  When available, the usage of TOP TIER Detergent Gasoline is recommended.  Visit www.toptiergas.com for a list of top tier detergent gasoline retailers.  Indiscriminate use of fuel system cleaning agents should be avoided.  Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients.  These can harm fuel system gasket and diaphragm materials.  Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small", "especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel", "operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the", "is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine", "clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you", "good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  Open the fuel filler door.  Fuel Filler Door Remove the diesel fuel filler cap by rotating it counterclockwise.  Fuel and Diesel Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the", "Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the vehicle with fuel.  When the nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel filler door.", "There may also be a second 115 V (400 W) maximum exterior power inverter located on the rear right side of the truck bed near the tailgate.  This inverter can be turned on by the Instrument Panel Power Inverter switch located to the left of the steering wheel.  This inverter can power cellular phones, electronics and other low power devices requiring power up to 400 W. Certain video game consoles exceed this limit, as will most power tools.  The indicator light on the power inverter switch will be illuminated when the inverter is turned on.  Exterior Truck Bed Power Inverter (If Equipped) A third and fourth USB port are located behind the center console, above the power inverter.  Both ports are charge only.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.", "of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's", "not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Power Inverters \u2014 If Equipped There is a 115 V (400 W) maximum inverter outlet located on the back of the center console to convert Direct Current (DC) to Alternating Current (AC).  This outlet can power cellular", "console to convert Direct Current (DC) to Alternating Current (AC).  This outlet can power cellular phones, electronics and other low power devices requiring power up to 400 W. Certain video game consoles exceed this power limit, as will most power tools.  There may also be a second 115 V (400 W) maximum exterior power inverter located on the rear right side of the truck bed near the tailgate.  This inverter can be turned on by the Instrument Panel Power Inverter switch located to the left of the steering wheel.  This inverter can power cellular phones, electronics and other low power devices requiring power up to 400 W. Certain video game consoles exceed this limit, as will most power tools.  The indicator light on the power inverter switch will be illuminated when the inverter is turned on.  The power inverter is designed with built-in overload protection.  If the power rating of 400 W is exceeded, the power inverter automatically shuts down.  Once the electrical device has been removed from the outlet,", "inverter automatically shuts down.  Once the electrical device has been removed from the outlet, the inverter should automatically reset.  Note: 400 W is the maximum for the inverter, not each outlet.  If two outlets are in use, 400 W is shared among the devices plugged in.  Note: The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is", "the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's", "not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage.", "Rear door removal rear door removal \u00b9 use this qr code to access your digital experience.  To remove the rear doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nuts from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin under the rear seat.  Hinge pin nut slide the front seat(s) fully forward.  Pry open and remove the plastic wiring access door from the bottom of the B-pillar.  Wiring access door unplug the wiring connector.  Note: squeeze the tab on the base of the wiring harness.  This will unlock the connector tab, allowing the wiring connector to be unplugged.  Unhook the wire harness strap from the hook on the body side.  Store the wire connector in the lower basket of the door.  Wiring connector with the door in the open position, remove the check bolt from the door check attachment on the body (using a #t40 torx head driver).  Note: keep the check arm in the extended position", "on the body (using a #t40 torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  To reinstall the door(s), perform the previous steps in the reverse order.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened", "to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  WARNING: To avoid personal injury be sure to keep your arms, hands, fingers and all objects clear of the check arm area during the removal and installation procedures.  Note: The upper hinge has a longer pin, which can be used to assist in guiding the door into place when reinstalling.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Front door removal front door removal \u00b9 use this qr code to access your digital experience.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement", "on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  To remove the front doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nut from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin located under the rear seat.  Hinge pin nut remove the plastic wiring access door under the instrument panel by sliding the plastic panel along the door frame toward the seats until the tabs are detached.  Wiring access door note: do not force open; this will break the plastic cover.  Pull up on the red locking tab to unlock the wiring harness.  Closed wiring harness 1 \u2014 red locking tab 2 \u2014 wiring harness lever (closed position) push and hold down the black security tab under the wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014", "the wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014 wiring harness lever (open position) 2 \u2014 black security tab with the wiring harness open, pull straight downward on the wiring connector to unplug.  Store the wiring connector in the lower door basket.  With the door in the open position, remove the check screw from the door check attachment on the body side (using a #T40 Torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  See note below if the check arm gets pushed into the door while the door is off.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.", "operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Note: When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door", "Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.", "Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  WARNING: Fast spinning tires can be dangerous.  Forces generated by excessive wheel speeds may cause tire damage or failure.  A tire could explode and injure someone.  Do not spin your vehicle's wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.  Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering,", "may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive", "safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand,", "brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be", "may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades seeCAUTION: Never use Non-Detergent Oil or", "occur.  For the recommended viscosity and quality grades seeCAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy", "significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.", "Biodiesel Fuel Properties \u2014 Low Ambient Temperatures Biodiesel fuel may gel or solidify at low ambient temperatures, which may pose problems for both storage and operation.  Precautions can be necessary at low ambient temperatures, such as storing the fuel in a heated building or a heated storage tank, or using cold temperature additives.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Biodiesel fuel may gel or solidify at low ambient temperatures, which may pose problems for both storage and operation.  Precautions can be necessary at low ambient temperatures, such as storing the fuel in a heated building or a heated storage tank, or using cold", "temperatures, such as storing the fuel in a heated building or a heated storage tank, or using cold temperature additives.  Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up", "in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.", "Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers", "tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.", "Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.  Adaptive Cruise Control (ACC) Ready Indicator Light \u2014 If Equipped With a Premium Instrument Cluster This light will turn on when the vehicle equipped with Adaptive Cruise Control (ACC) has been turned on, but not set.  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speedCruise Control SET Indicator Light \u2014 If Equipped With A Base Instrument Cluster This indicator light will illuminate when the cruise control is set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but", "Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  This indicator will illuminate when the hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety", "slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  This indicator will illuminate when the hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant", "hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully", "to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Release both of the outside hood latches.", "Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  If the \u201cSERVICE POWER STEERING\u201d", "Normal operation will resume once the system is allowed to cool.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function.  However, the effort required to brake the vehicle will be much greater than that required with the power system operating.  If the stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the", "stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not attempt to drive the vehicle over 18 mph (29 km/h).  Driving faster than 18 mph (29 km/h) with a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  When the condition that deactivated the system is no longer present, the system will return to the \u201cAdaptive Cruise Control Off\u201d state and will resume function by simply reactivating it.  There may be situations where the Hill Start Assist (HSA) will not activate and slight rolling may occur, such as on minor hills or with a loaded vehicle, or while pulling a trailer.  HSA is not a substitute for active driving involvement.  It is always the", "while pulling a trailer.  HSA is not a substitute for active driving involvement.  It is always the driver\u2019s responsibility to be attentive to distance to other vehicles, people, and objects, and most importantly brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision or serious personal injury.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized", "on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off CAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial", "it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may", "are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offCAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.", "Off-Road Driving Tips  Soft sand is very difficult to travel through with full tire pressure.  When crossing soft, sandy spots in a trail, maintain your vehicle's momentum and do not stop.  The key to driving in soft sand is using the appropriate tire pressure, accelerating slowly, avoiding abrupt maneuvers and maintaining the vehicle's momentum.  If you are going to be driving on large soft sandy areas or dunes, reduce your tire pressure to a minimum of 15 psi (103 kPa) to allow for a greater tire surface area.  Reduced tire pressure will drastically improve your traction and handling while driving on the soft sand, but you must return the tires to normal air pressure before driving on pavement or other hard surfaces.  Be sure you have a way to reinflate the tires prior to reducing the pressure.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass,", "proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and", "left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  Sand Soft sand is very difficult to travel through with full tire pressure.  When crossing soft, sandy spots in a trail, maintain your vehicle's momentum and do not stop.  The key to driving in soft sand is using the appropriate tire pressure, accelerating slowly, avoiding abrupt maneuvers and maintaining the vehicle's momentum.  If you are going to be driving on large", "abrupt maneuvers and maintaining the vehicle's momentum.  If you are going to be driving on large soft sandy areas or dunes, reduce your tire pressure to a minimum of 15 psi (103 kPa) to allow for a greater tire surface area.  Reduced tire pressure will drastically improve your traction and handling while driving on the soft sand, but you must return the tires to normal air pressure before driving on pavement or other hard surfaces.  Be sure you have a way to reinflate the tires prior to reducing the pressure.  CAUTION: Reduced tire pressures may cause tire unseating and total loss of air pressure.  To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneuvers.", "US/CANADA Exposure to Radio Frequency Radiation The radiated output power of the internal wireless radio is far below the FCC and IC radio frequency exposure limits.  Nevertheless, the wireless radio will be used in such a manner that the radio is 8 inches (20 cm) or further from the human body.  The internal wireless radio operates within guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community.  The radio manufacturer believes the internal wireless radio is safe for use by consumers.  The level of energy emitted is far less than the electromagnetic energy emitted by wireless devices such as mobile phones.  However, the use of wireless radios may be restricted in some situations or environments, such as aboard airplanes.  If you are unsure of restrictions, you are encouraged to ask for authorization before turning on the wireless radio \"\u21e8general information\" .  Vehicle body care requirements vary according to geographic locations and", "\"\u21e8general information\" .  Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for", "the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.", "extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking", "others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.  The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window", "switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  Power Window Switches Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.  Window Lockout Switch The window lockout switch allows you to disable the window controls on the rear passenger doors.  To disable the window controls, rotate the switch", "the window controls on the rear passenger doors.  To disable the window controls, rotate the switch downward.  To enable the window controls, rotate the switch upward.", "Speedometer push and release the up or down arrow button until the speedometer menu icon is displayed in the instrument cluster display.  Push and release the ok button to toggle between mph and km/h.  Instrument cluster descriptions tachometer indicates the engine speed in revolutions per minute (rpm x 1000).  Caution: do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature gauge the temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle", "boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Caution: driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument cluster display the instrument cluster display features a driver interactive display.  Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer indicates vehicle speed.  Speedometer push and release the up or down arrow button until the speedometer menu icon is displayed in the instrument cluster display.  Push and release the ok button to toggle between mph and km/h.", "in the instrument cluster display.  Push and release the ok button to toggle between mph and km/h.  Favorite menus speedometer vehicle info off road \u2014 if equipped (show/hide) driver assist \u2014 if equipped (show/hide) fuel economy (show/hide) trip info (show/hide) stop / start \u2014 if equipped audio (show/hide) messages screen setup vehicle settings \u2014 if equipped.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by", "operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will", "will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer", "driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display If an obstacle is detected in the center front region, the display will show a single solid arc in the center front region with no chime.  As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and a fast sound tone will be heard and will change from fast, to continuous.", "Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go", "At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting", "and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine", "Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable", "battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain", "could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Secondary Battery", "booster pack, follow the manufacturer's operating instructions and precautions.  Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.", "Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact", "background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected,", "will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text", "allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press", "6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a", "Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.", "Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel", "only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damageIf climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway", "Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good", "using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  CAUTION: If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage Diesel Fuel Specifications This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine", "tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump", "at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).", "To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to", "equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed", "Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster Vehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.", "After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle", "or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the", "of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Transmission function is monitored electronically for abnormal conditions.  If a condition is detected that could result in transmission damage, Transmission Limp Home mode is activated.  In this mode, the transmission may operate only in certain gears, or may not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some situations, the transmission may not re-engage if the engine is turned off and restarted.  The Malfunction Indicator Light (MIL) may be illuminated.  A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary.  It is important to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only manufacturer's specified transmission fluid It is important to maintain the transmission fluid at the correct level using the", "fluid It is important to maintain the transmission fluid at the correct level using the recommended fluid.  Using a transmission fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  Using a lower gear while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  This action will also provide better engine braking.  Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission", "or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing a heavy trailer), use the AutoStick shift control to select a lower gear Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels", "\u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  During cold weather, you may experience increased effort in shifting until the transmission fluid warms up.  This is normal.  Routine fluid and filter changes are not required.  However, change the fluid and filter if the fluid becomes contaminated (with water, etc.  ), or if the transmission is disassembled for any reason.", "It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in", "possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster", "If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function.  However, the effort required to brake the vehicle will be much greater than that required with the power system operating.  If the stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not", "Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not attempt to drive the vehicle over 18 mph (29 km/h).  Driving faster than 18 mph (29 km/h) with a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  When the condition that deactivated the system is no longer present, the system will return to the \u201cAdaptive Cruise Control Off\u201d state and will resume function by simply reactivating it.  There may be situations where the Hill Start Assist (HSA) will not activate and slight rolling may occur, such as on minor hills or with a loaded vehicle, or while pulling a trailer.  HSA is not a substitute for active driving involvement.  It is always the driver\u2019s responsibility to be attentive to distance to other", "driving involvement.  It is always the driver\u2019s responsibility to be attentive to distance to other vehicles, people, and objects, and most importantly brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision or serious personal injury.  Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension", "of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.", "ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster displayIt provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.  The ParkSense Park Assist system provides visual and audible indications of the distance between the rear and/or front fascia/bumper and a detected obstacle when backing up or moving forward (e.g.  during a parking maneuver).  For system limitations and usage precautions, see ParkSense will turn off the Front Park Assist audible alert (chime) after approximately three seconds when an obstacle has been detected, the vehicle is stationary, and the brake pedal is applied.  ParkSense can be active only when the gear selector is in REVERSE or DRIVE.  If ParkSense is enabled at one of these gear selector positions, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above.  A warning will appear in the instrument cluster", "to approximately 7 mph (11 km/h) or above.  A warning will appear in the instrument cluster display indicating the vehicle is above ParkSense operating speed.  The system will become active again if the vehicle speed is decreased to less than approximately 6 mph (9 km/h).  The ParkSense Warning screen is located within the instrument cluster display It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.  ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles.  Parking curbs might be temporarily detected or not detected at all.  Obstacles located above or below the sensors will not be detected when they are in close proximity.  The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected.  It is recommended that the driver looks over his/her shoulder when using ParkSense.  Setting Name Description Forward Collision", "looks over his/her shoulder when using ParkSense.  Setting Name Description Forward Collision Warning Sensitivity This setting will change the distance at which the Forward Collision Warning (FCW) alert sounds.  The \u201cMedium\u201d setting will have the FCW system signal when an object is in view, and the possibility of a collision is detected.  The \u201cNear\u201d setting will have the FCW system signal when the object is closer to the vehicle.  The \u201cFar\u201d setting will have the FCW system signal when an object is at a far distance from the vehicle.  Forward Collision Warning This setting will turn the Forward Collision Warning system on or off.  The \u201cOff\u201d setting will deactivate the FCW system.  The \u201cWarning Only\u201d setting will provide only an audible chime when a collision is detected.  The \u201cWarning + Active Braking\u201d setting will provide an audible chime and apply some brake pressure when a collision is detected.  ParkSense This setting will change the type of ParkSense alert when a close object is detected and can provide", "setting will change the type of ParkSense alert when a close object is detected and can provide both an audible chime and a visual display when an object is detected.  Front ParkSense Volume This setting adjusts the volume of the Front ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Rear ParkSense Volume This setting adjusts the volume of the Rear ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Blind Spot Alert This setting will change the type of alert provided when an object is detected in a vehicle\u2019s blind spot.  The \u201cOff\u201d setting will turn off Blind Spot Alert.  The \u201cLights\u201d setting will activate the Blind Spot Alert lights on the outside mirrors.  The \u201cLights & Chime\u201d setting will activate both the lights on the outside mirrors and an audible chime.  Hill Start Assist This setting will turn the Hill Start Assist system on or off.  ParkView Backup Camera Active Guidelines This setting will turn the ParkView Backup Camera Active Guidelines on or off.", "Active Guidelines This setting will turn the ParkView Backup Camera Active Guidelines on or off.  ParkView Backup Camera Delay This setting will add a timed delay to the ParkView Backup Camera when shifting out of REVERSE.  Fixed ParkView Backup Camera Guidelines This setting will turn the Fixed ParkView Backup Camera Guidelines on or off.  Front Camera Gridlines This setting will turn the Front Camera Gridlines on or off.  Tire Fill Assist This setting will turn Tire Fill Assist on or off.  ParkSense Sensors The four ParkSense sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 79 inches (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.  The six ParkSense sensors, located in the front fascia/bumper, monitor the area in front of the vehicle that is within the sensors\u2019 field of view.", "fascia/bumper, monitor the area in front of the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 47 inches (120 cm) from the front fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.", "Fuel Filler Cap The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Open the fuel filler door.  Fuel filler door remove the fuel cap by rotating it counterclockwise.  Fuel filler cap fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the", "is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light (MIL) to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  CAUTION: Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Note: When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure", "tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque", "cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern", "torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners Loosen the fasteners from the engine air cleaner filter cover using a suitable tool.  Engine Air Cleaner Filter Cover 1 \u2014 Fasteners 2 \u2014 Engine Air Cleaner Filter Cover Lift the engine air cleaner filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from", "filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from the housing assembly.  engine air cleaner filter cover  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  After fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged.  If the system detects a malfunction, the \u201cgASCAP\u201d message will display in the odometer display.  Tighten the gas cap until a \"clicking\" sound is heard.  This is an indication that the gas cap is properly tightened.  Push the odometer reset button to turn the message off.  If the problem persists, the message will appear the next time the vehicle is started.  This might indicate", "persists, the message will appear the next time the vehicle is started.  This might indicate a damaged cap.  If the problem is detected twice in a row, the system will turn on the MIL.  Resolving the problem will turn the MIL off.  The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.", "Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the", "is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your", "with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.  Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove", "the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Rear Carpet Remove the grommets under the front seat (one left and one right).  Carpet split then pull the carpet out, to the rear and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin (if equipped), by removing the four bolts that hold it to the floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then lift the assembly out from under the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear retainers remove", "the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear retainers remove carpet from the vehicle.  When reinstalling the carpet, perform these steps in reverse order making sure that the carpet is tucked under the scuffs, B-pillar, console, and then refasten the grommets.  Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach", "and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to", "check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.", "Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be", "Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire dealer or original", "those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result", "what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw", "accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Tire pressures change by approximately 1 psi (7 kPa) per 12\u00b0F (7\u00b0C) of air temperature change.  Keep this in mind when checking tire pressure inside a garage, especially in the Winter.  Jacking and tire changing \u00b9 use this qr code to access your digital experience.  Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: At Every Oil Change Interval As Indicated By Oil Change Indicator System: Change oil and filter.  Rotate the tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on.  Inspect battery and clean and tighten terminals as required.", "the oil indicator system turns on.  Inspect battery and clean and tighten terminals as required.  Inspect the CV/Universal joints.  Inspect brake pads, shoes, rotors, drums, hoses and parking brake.  Inspect engine cooling system protection and hoses.  Inspect exhaust system.  Inspect engine air cleaner filter if using in dusty or off-road conditions, replace engine air cleaner filter if necessary.  Inspect all door latches for presence of grease, reapply if necessary.  Do not continue driving with one or more flat tires as handling may be compromised.  Stop the vehicle, avoiding sharp braking and steering.  If a tire puncture occurs, repair immediately using the dedicated tire repair kit and contact an authorized dealer as soon as possible.  Consult an authorized tire dealer for tire repairs and additional information.  In the Selectable Tire Fill Alert application, which is located in the apps menu of the Uconnect system, you will be able to select a pressure setting for both the front and rear axle tire", "system, you will be able to select a pressure setting for both the front and rear axle tire pressures by scrolling through a pressure range from XX to 15 psi in 1 psi increments for each axle setting.  After inspecting or adjusting the tire pressure, always reinstall the valve stem cap.  This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.  Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under", "slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.", "4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  Yellow indicator lights 4wd indicator light \"\u21e84wd indicator light \u2014 if equipped\" 4wd low indicator light \"\u21e84wd low indicator light \u2014 if equipped\" 4wd part time indicator light \"\u21e84wd part time indicator light \u2014 if equipped\" axle locker fault indicator light \"\u21e8axle locker fault indicator light \u2014 if equipped\" rear axle lock indicator light \"\u21e8rear axle lock indicator light \u2014 if equipped\" front and rear axle lock indicator light \"\u21e8front and rear axle lock indicator light \u2014 if equipped\" forward collision warning off indicator light \"\u21e8forward collision warning off indicator light \u2014 if equipped\" neutral indicator light \"\u21e8neutral indicator light \u2014 if equipped\" sway bar indicator light \"\u21e8sway", "neutral indicator light \"\u21e8neutral indicator light \u2014 if equipped\" sway bar indicator light \"\u21e8sway bar indicator light \u2014 if equipped\" off road+ indicator light \"\u21e8off road+ indicator light \u2014 if equipped\" cargo light on indicator light \"\u21e8cargo light on indicator light\" wait to start indicator light \"\u21e8wait to start indicator light \u2014 if equipped\" low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \"\u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped\" water in fuel indicator light \"\u21e8water in fuel indicator light \u2014 if equipped\" selec speed control (ssc) indicator light \u2014 if equipped this light will turn on when selec speed control is activated.  Selec Speed Control is available in 4WD Low ONLY.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear", "forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  Yellow indicator lights 4wd indicator light  \u21e84wd indicator light \u2014 if equipped  4wd low indicator light  \u21e84wd low indicator light \u2014 if equipped  4wd part time indicator light  \u21e84wd part time indicator light \u2014 if equipped  axle locker fault indicator light  \u21e8axle locker fault indicator light \u2014 if equipped  rear axle lock indicator light  \u21e8rear axle lock indicator light \u2014 if equipped  front and rear axle lock indicator light  \u21e8front and rear axle lock indicator light \u2014 if equipped  forward collision warning off indicator light", "and rear axle lock indicator light \u2014 if equipped  forward collision warning off indicator light  \u21e8forward collision warning off indicator light \u2014 if equipped  neutral indicator light  \u21e8neutral indicator light \u2014 if equipped  sway bar indicator light  \u21e8sway bar indicator light \u2014 if equipped  off road+ indicator light  \u21e8off road+ indicator light \u2014 if equipped  cargo light on indicator light  \u21e8cargo light on indicator light  wait to start indicator light  \u21e8wait to start indicator light \u2014 if equipped  low diesel exhaust emissions additive adblue\u00ae (urea) indicator light  \u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped  water in fuel indicator light  \u21e8water in fuel indicator light \u2014 if equipped  green indicator lights 4wd auto indicator light  \u21e84wd auto indicator light \u2014 if equipped  front fog indicator light  \u21e8front fog indicator light \u2014 if equipped  parking/headlights on indicator light  \u21e8parking/headlights on indicator light  stop/start active indicator light  \u21e8stop/start", "light  \u21e8parking/headlights on indicator light  stop/start active indicator light  \u21e8stop/start active indicator light \u2014 if equipped  turn signal indicator lights  \u21e8turn signal indicator lights  rear seat belt fastened indicator light.", "Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  Jacking and tire changing jacking and tire", "by jacking on locations other than those indicated.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a", "only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended", "make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using", "a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review", "installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can", "jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.", "DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.", "stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as", "similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody", "and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the", "child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.", "ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be", "may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality", "conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Introduction To Connected Vehicle Services One of the many benefits of your vehicle\u2019s Uconnect system is that you can now take advantage of SiriusXM Guardian\u2122 connected services.  To unlock the full potential of SiriusXM Guardian\u2122 in your vehicle, you first need to activate SiriusXM Guardian\u2122 connected services.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.", "Failure to follow these warnings can result in a collision and death or serious personal injury.  Note: SiriusXM Guardian\u2122 involves the collection, transmission and use of data from your vehicle  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use", "operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes", "in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades seeCAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.", "Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the", "windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the", "EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engineThis allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined", "is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact.  Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.  This feature notifies the user when the placard tire pressure is attained while inflating or deflating the tire.  Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.", "can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof", "to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  The functions described are for when the Jeep\u00ae wireless speaker is undocked from the vehicle.  When plugged into the docking station, the Jeep\u00ae wireless speaker functions as part of the vehicle\u2019s sound system.  The Jeep\u00ae wireless speaker is IP67 waterproof certified with design in mind to withstand rainfall, waterjets, splashing and being submerged in up to 3 ft (1 m) of water for up to 30 minutes.", "N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.  See Recreational Towing for further information WARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll,", "both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) NEUTRAL (N)  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.", "To ensure proper engine lubrication, the engine oil must be maintained at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Check engine oil level Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage Check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed Check function of all interior and exterior lights  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or", "oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  The engine oil filter should be replaced with a new filter at every engine oil change.  A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.", "Window Lockout Switch The window lockout switch allows you to disable the window controls on the rear passenger doors.  To disable the window controls, rotate the switch downward.  To enable the window controls, rotate the switch upward.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to", "A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  Power Door Lock Switch Push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone Push the lock button on the key fob.", "Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact.  Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.  This feature notifies the user when the placard tire pressure is attained while inflating or deflating the tire.  Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.", "can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof", "to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  The functions described are for when the Jeep\u00ae wireless speaker is undocked from the vehicle.  When plugged into the docking station, the Jeep\u00ae wireless speaker functions as part of the vehicle\u2019s sound system.  The Jeep\u00ae wireless speaker is IP67 waterproof certified with design in mind to withstand rainfall, waterjets, splashing and being submerged in up to 3 ft (1 m) of water for up to 30 minutes.", "Transmission Temperature Warning Light \u2014 If Equipped This warning light will illuminate to warn of a high transmission fluid temperature.  This may occur with strenuous usage such as trailer towing.  If this light turns on, stop the vehicle and run the engine at idle or slightly faster, with the transmission in PARK (P) or NEUTRAL (N), until the light turns off.  Once the light turns off, you may continue to drive normally.  If Manual transmission equipped, this warning will illuminate to warn of high clutch temperature.  This may occur with driver misuse of clutch pedal or resting foot on the clutch pedal or partially engaging the clutch for longer duration.  If the light turns on, it will be with an additional CLUTCH HOT message.  Stop the vehicle safely and run the engine at idle with transmission gear in NEUTRAL (N) until the light turns off.  Once the light turns off, follow the message displayed in the instrument cluster.  WARNING: If you continue operating the vehicle when the Transmission Temperature", "cluster.  WARNING: If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  CAUTION: Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the", "is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is", "the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not", "illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  In", "Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure.  This could damage your engine.  Engine misfiring or vibrating severely Sudden loss of power Unusual engine noises Fuel, oil or coolant leaks Sudden change, outside the normal operating range, in the engine", "noises Fuel, oil or coolant leaks Sudden change, outside the normal operating range, in the engine operating temperature Excessive smoke Oil pressure drop If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  Vehicle info push and release the up or down arrow button until the vehicle info menu icon is displayed in the instrument cluster display.  Push and release the left or right arrow button to scroll through the information submenus and push and release the ok button to select or reset the resettable submenus.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is", "information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  Service Forward Collision Warning (FCW) Light \u2014 If Equipped This warning light will illuminate to indicate a fault in the Forward Collision Warning System.  Contact an authorized dealer for service Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable", "is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.", "Component fluid, lubricant, or genuine part automatic transmission \u2013 if equipped use only mopar\u00ae zf 8 & 9 speed atf automatic transmission fluid or equivalent.  Failure to use the correct fluid may affect the function or performance of your transmission.  Manual transmission \u2013 if equipped we recommend using mopar\u00ae atf+4 automatic transmission fluid.  Transfer case we recommend using mopar\u00ae atf+4 automatic transmission fluid.  Front axle differential we recommend using mopar\u00ae gear & axle lubricant (sae 75w85) (api gl-5).  Rear axle differential (m220 sales codes dre/drf) we recommend using mopar\u00ae gear & axle lubricant (sae 75w85) (api gl-5).  Models equipped with Trac-Lok Limited Slip Differential require a friction modifier additive.  Brake master cylinder we recommend using mopar\u00ae dot 3 brake fluid, sae j1703.  Power steering reservoir we recommend using mopar\u00ae electric steering pump fluid.  Synthetic Engine Oils Your engine was designed for synthetic engine oils, only use synthetic API approved engine", "Oils Your engine was designed for synthetic engine oils, only use synthetic API approved engine oils.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Component Fluid, Lubricant, or Genuine Part Automatic Transmission \u2013 If Equipped Use only Mopar\u00ae ZF 8 & 9 Speed ATF Automatic Transmission Fluid or equivalent.  Failure to use the correct fluid may affect the function or performance of your transmission.  Manual", "to use the correct fluid may affect the function or performance of your transmission.  Manual Transmission \u2013 If Equipped We recommend using Mopar\u00ae ATF+4 Automatic Transmission Fluid.  Transfer Case We recommend using Mopar\u00ae ATF+4 Automatic Transmission Fluid.  Front Axle Differential We recommend using Mopar\u00ae Gear & Axle Lubricant (SAE 75W85) (API GL-5).  Rear Axle Differential (M220 Sales Codes DRE/DRF) We recommend using Mopar\u00ae Gear & Axle Lubricant (SAE 75W85) (API GL-5).  Models equipped with Trac-Lok Limited Slip Differential require a friction modifier additive.  Brake Master Cylinder We recommend using Mopar\u00ae DOT 3 Brake Fluid, SAE J1703.  Power Steering Reservoir We recommend using Mopar\u00ae Electric Steering Pump Fluid.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and", "gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or", "width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013", "load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire if a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: the gvwr is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured", "(one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 What is the phone number for roadside assistance call?  The phone number is: US: 1-800-521-2779 Canada: 1-800-363-4869 If I am subscribed to SiriusXM Guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance?  No, however your new vehicle may include Roadside Assistance Call services.  Setting Name Description Voice Response Length This setting will change the response length for the Voice Recognition system.  The \u201cBrief\u201d setting provides a shortened audio description from the system.  The \u201cDetailed\u201d setting provides the full audio description from the system.", "from the system.  The \u201cDetailed\u201d setting provides the full audio description from the system.  Show Command List This setting will allow you to turn the Command List on or off.  The \u201cAlways\u201d setting will always show the Command List.  The \u201cWith Help\u201d setting will show the Command List and provide a brief description of what the command does.  The \u201cNever\u201d setting will turn the Command List off.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is", "provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer", "OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the", "prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).", "Cruise control set indicator light \u2014 if equipped with a premium instrument cluster this indicator light will illuminate when the cruise control is set to the desired speed \"\u21e8cruise control\" .  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speedCruise Control SET Indicator Light \u2014 If Equipped With A Base Instrument Cluster This indicator light will illuminate when the cruise control is set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.  Adaptive Cruise", "This light will turn on when the cruise control has been turned on, but not set.  Adaptive Cruise Control (ACC) Ready Indicator Light \u2014 If Equipped With a Premium Instrument Cluster This light will turn on when the vehicle equipped with Adaptive Cruise Control (ACC) has been turned on, but not set.", "Vehicle Identification Number Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.  VEHICLE IDENTIFICATION NUMBER (VIN) The VIN is found on the left front corner of the A-pillar, visible from outside of the vehicle through the windshield.  Note: It is illegal to remove or alter the VIN plate.  Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle", "driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.", "Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic modeENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch", "features.  Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the Autostop function will be disabled Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the Autostop function will be disabled When Seats & Comfort/Auto-On Comfort Systems button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s comfort systems when remote start has been activated or the vehicle has been started.  Depending on the vehicle\u2019s options, feature settings may vary.  This system offers a full complement of manual override features.  The AUTO symbol in the front ATC display will be turned off when the system is being used in the manual mode.  When the Safety/Driving Assistance button is", "off when the system is being used in the manual mode.  When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Depending on the vehicle\u2019s options, feature settings may vary.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  When the AUX button is pressed on the touchscreen, the system displays the options related to the four vehicle AUX switches: Depending on the vehicle\u2019s options, feature settings may vary.  AUTO", "the four vehicle AUX switches: Depending on the vehicle\u2019s options, feature settings may vary.  AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic modeWhen Seats & Comfort/Auto-On Comfort Systems button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s comfort systems when remote start has been activated or the vehicle has been started.  Note: depending on the vehicle\u2019s options, feature settings may vary.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on", "vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons  AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic mode \"\u21e8automatic operation\" .", "There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch", "be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly With the help of a second person, set the Sunrider\u00ae top onto the top of the vehicle making sure to align the holes at the front and rear of the side rails.  Lower Sunrider\u00ae Onto The Vehicle Swing the front frame bracket around the side of the rail, and insert the door rail attachment bolt (provided bolt without spacer) from underneath.  Tighten with a #40 Torx head driver until snug.  Attach Front Door Rail Bolt Insert the rear door rail attachment bolt (provided bolt with spacer) from underneath.  Tighten with #40 Torx head driver until snug.  Attach Rear Door Rail Bolt Repeat steps 3 and 4 on the other side of the vehicle.  The recommended torque specification for the front and rear door rail attachment bolts is 8.8 ft-lb (12 N\u00b7m).  Attach the rear clamp at the rear center of the Sunrider\u00ae top", "bolts is 8.8 ft-lb (12 N\u00b7m).  Attach the rear clamp at the rear center of the Sunrider\u00ae top using the two provided rear clamp attachment bolts.  Tighten with #40 Torx head driver until snug.  Rear Clamp Location The recommended torque specification for the rear clamp attachment bolts is 3.7 ft-lb (5 N\u00b7m).  From inside the vehicle, lift and pull the Sunrider\u00ae top forward using the integrated handle on the front header of the top.  Manually guide the top into the closed position.  Push Sunrider\u00ae Top Forward From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Pull the handle back upward while squeezing the hook, locking the latch into place.  Repeat on the other side.  Engage Both Header Latches Lug Nut/Bolt Torque **Lug Nut/Bolt Size Lug Nut/Bolt Socket Size 130 ft-lb (176 N\u00b7m) M14 x 1.50 mm 22 mm After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  There are two nuts", "to be sure that all the lug nuts/bolts are properly seated against the wheel.  There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  To reinstall the door(s), perform the previous steps in the reverse order.  Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so", "in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  Prior to off-road usage, the side steps should be removed to prevent damage.  There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Prior to off-road usage, the side steps should be removed to prevent", "procedure for the other side.  Prior to off-road usage, the side steps should be removed to prevent damage.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step", "panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.", "The instrument cluster display will return to the last display selected after five seconds of no ACC display activity.  The instrument cluster display will return to the last display selected after five seconds of no ACC display activity.  Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.  The instrument cluster", "the specific information you want to make selections and adjustments.  The instrument cluster display will show the current ACC system settings.  The instrument cluster display is located in the center of the instrument cluster.  The information it displays depends on ACC system status.  When the system is turned on and in the ready state, the instrument cluster displays \u201cACC Ready.\u201d The instrument cluster display features a driver interactive display When the system is off, the instrument cluster displays \u201cAdaptive Cruise Control (ACC) Off.\u201d If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.  If the problem is not solved, a specific message will appear on the Instrument Cluster Display whenever a certain threshold is reached until it will no longer be possible to start the engine.  The instrument cluster display displays the current ACC system settings.  The information displayed depends on ACC system status.  INSTRUMENT", "current ACC system settings.  The information displayed depends on ACC system status.  INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.  ACC SET When ACC is set, the set speed will display in the instrument cluster.  The acc screen may display once again if any acc activity occurs, which", "in the instrument cluster.  The acc screen may display once again if any acc activity occurs, which may include any of the following: system cancel driver override system off acc proximity warning acc unavailable warning note: the instrument cluster display will return to the last display selected after five seconds of no acc display activity.  INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the", "your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.  Adaptive Cruise Control Ready When ACC is activated but the vehicle speed setting has not been selected, the display will read \u201cAdaptive Cruise Control Ready.\u201d Push the SET + or the SET - button (located on the steering wheel), and the following will display in the instrument cluster display.", "TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your", "And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  To close the tailgate, lift upward until both sides latch into place.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to", "this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before", "it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your", "flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.", "The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  Power Door Lock Switch Push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob", "door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone Push the lock button on the key fob.  INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.", "Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the", "form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited", "This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system", "of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use", "or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling,", "to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying", "this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced", "a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that", "Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.", "Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.  Stationary Objects And Vehicles ACC does not react to stationary objects or vehicles.  For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane.  It will consider this stopped vehicle a stationary object as it did not previously detect movement from it.  Always be attentive and ready to apply the brakes if necessary.  The ACC screen may display once again if any ACC activity occurs, which may include any of the following: This feature will only activate when the following conditions are met: The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS", "gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: Once SSC is enabled it will activate automatically once the following conditions are met: The following conditions must be met in order for HSA to activate:", "Diesel Fuel Specifications This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials)", "2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized", "generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and", "Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The", "ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better", "fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD", "of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is", "or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the", "using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result", "API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  Open the fuel filler door.  Fuel Filler Door Remove the diesel fuel filler cap by rotating it counterclockwise.  Fuel and Diesel Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the vehicle with fuel.  When the nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel filler door.", "Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death", "be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated", "de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  The battery in your vehicle is located in the right rear of the engine compartment.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front", "vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  The Power Distribution Center is located in the engine compartment near the battery.  This center contains cartridge fuses, mini fuses, and relays.  The PDC top cover is labeled with each serviceable fuse/relay location, function, and size.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead", "to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with", "compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.", "If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is", "center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator,", "After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough", "not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a", "changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.", "When To Use 4L Range When off-road driving, shift into 4L for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low speed pulling power.  This range should be limited to extreme situations such as deep snow, mud, steep inclines, or sand where additional low speed pulling power is needed.  Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4L range.  CAUTION: Do not use 4L range when operating the vehicle on dry pavement.  Driveline hardware damage can result.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street", "in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument", "to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the", "provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the", "4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.", "JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in", "pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water", "If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are", "is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-)", "battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a", "If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift", "two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the", "compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure", "Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.  Note: Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle while making connections.", "Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately \"\u21e8air bag warning light\" .  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning", "as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bags to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Placing an object on", "you drive, have an authorized dealer service the air bag system immediately.  Placing an object on the floor under the front passenger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision.  Do not place any objects on the floor under the front passenger seat.  If there is a fault present in the OCS, both the PAD Indicator Light and the Air Bag Warning Light will illuminate to show that the Passenger Advanced Front Air Bag is deactivated.  Should this occur, the Passenger Advanced Front Air Bag will remain deactivated until the fault is cleared.  This indicates that you should take the vehicle to an authorized dealer for service immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light", "Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light will illuminate whenever the ocs is unable to classify the front passenger seat status.  A malfunction in the OCS may affect the operation of the air bag system.  If the air bag warning light does not come on, or stays on after you start the vehicle, or it comes on as you drive, take the vehicle to an authorized dealer for service immediately.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check", "Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Air Bag Warning Light This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on", "stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  Air Bag Warning Light The Occupant Restraint Controller (ORC) monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position.  If the ignition switch is in the OFF position or in the ACC position, the air bag system is not on and the air bags will not inflate.  The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or it becomes disconnected prior to deployment.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light,", "If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is detected that could affect the air bag system.  The diagnostics also record the nature of the malfunction.  While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  Note: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint", "the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled.  In this condition the air bags may not be ready to inflate for your protection.  have an authorized dealer service the air bag system immediately.  WARNING: Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.", "Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling contacts from Phonebooks displayed on the touchscreen.  Setting Favorite Contact phone numbers so they are easily accessible on the Main Phone screen.  Viewing and Calling contacts from Recent Call logs.  Reviewing your recent Incoming SMS Messages.  Pairing up to 10 phones/audio devices for easy access to connect to them quickly.  Your mobile phone\u2019s audio is transmitted through your vehicle\u2019s audio system; the system will automatically mute your radio when using the Uconnect Phone.  For uconnect customer support: us visit uconnectphone.com or call 877-855-8400 canada visit uconnectphone.com or call 800-465-2001 (english) or (french) call 800-387-9983 uconnect phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile", "conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  Note: Your phone must be capable of SMS messaging via Bluetooth\u00ae for messaging features to work properly.  WARNING: ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the Uconnect features and applications in this vehicle.  Only use Uconnect when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Start using Uconnect Voice Recognition with", "in an accident involving serious injury or death.  Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: The following basic Voice Commands can be given at any point while using your Uconnect system.  Uconnect Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  Uconnect Phone is a voice-activated, hands-free, in-vehicle communications system.  It allows you to dial a phone number with your mobile phone.  Uconnect Phone will automatically", "It allows you to dial a phone number with your mobile phone.  Uconnect Phone will automatically connect to the highest priority paired phone and/or Audio Device within range.  If you need to choose a particular phone or audio device follow these steps: uconnect can announce incoming text messages.  Push the vr button or phone button and say: the phone feature is driven through your bluetooth\u00ae \u201chands-free profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected", "to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.  Safe Usage Of The Uconnect System The Uconnect system is a sophisticated electronic device.  Do not let young children use the system.  Permanent hearing loss may occur if you play your music or sound system at loud volumes.  Exercise caution when setting the volume on the system.  Keep drinks, rain and other sources of moisture away from the system.  Besides damage to the system, moisture can cause electric shocks as with any electronic device.  Note: Many features of this system are speed dependent.  For your own safety, it is not possible to use some of the touchscreen features while the vehicle is in motion.  Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling", "is in motion.  Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling contacts from Phonebooks displayed on the touchscreen.  Setting Favorite Contact phone numbers so they are easily accessible on the Main Phone screen.  Viewing and Calling contacts from Recent Call logs.  Reviewing your recent Incoming SMS Messages.  Pairing up to 10 phones/audio devices for easy access to connect to them quickly.  Your mobile phone\u2019s audio is transmitted through your vehicle\u2019s audio system; the system will automatically mute your radio when using the Uconnect Phone.  For uconnect customer support: us visit uconnectphone.com or call 877-855-8400 canada visit uconnectphone.com or call 800-465-2001 (english) or (french) call 800-387-9983 uconnect phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free", "for private conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  Note: Your phone must be capable of SMS messaging via Bluetooth\u00ae for messaging features to work properly.  WARNING: ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the Uconnect features and applications in this vehicle.  Only use Uconnect when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Multiple Devices Connecting To", "do so may result in an accident involving serious injury or death.  Multiple Devices Connecting To The Uconnect System \u2014 If Equipped It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.  Note: Apple CarPlay\u00ae and Android Auto\u2122 can only be launched from the front and center console USB ports.", "Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the", "the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other", "will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.", "4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front wheels.  The four-wheel drive system will be automatically engaged when the vehicle senses a loss of traction.  This range provides additional traction for varying road conditions.  2H Two-Wheel Drive High Range \u2014 This range is for normal street and highway driving on dry, hard surfaced roads.  4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front wheels.  The four-wheel drive system will be automatically engaged when the vehicle senses a loss of traction.  This range provides additional traction for varying road conditions.  4H Four-Wheel Drive High Range \u2014 This range maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction for loose, slippery road surfaces only.  Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels", "four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  2H (Two-Wheel Drive High Range) 4H (Four-Wheel Drive High Range) N (Neutral) 4L (Four-Wheel Drive Low Range) In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L", "Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  How To Engage The Automatic Locking Mode Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  This indicator will illuminate when a door is ajar/open and not fully closed.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down", "open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Door Latches Check for proper closing, latching, and locking.", "Full Off \u2014 If Equipped This mode is intended for off-highway or off-road use only and should not be used on any public roadways.  In this mode, TCS and ESC features are turned off.  To enter the \u201cFull Off\u201d mode, push and hold the ESC OFF button for five seconds while the vehicle is stopped with the engine running.  After five seconds, a chime will sound, the ESC OFF Indicator Light will illuminate, and the \u201cESC OFF\u201d message will display in the instrument cluster.  To turn ESC on again, momentarily push the ESC OFF button.  If equipped with Off Road+ and if Off Road+ is active when \"Full Off\" mode is enabled by the driver, ESC will not switch to \"Partial Off\" mode at any speed and will remain in \"Full Off\" mode until Off Road+ is exited or ESC is re-enabled by the driver.  Note: System may switch from ESC \u201cFull Off\u201d to \u201cPartial Off\u201d mode when vehicle exceeds a predetermined speed.  When the vehicle speed slows below the predetermined speed the system will return to ESC \u201cFull Off\u201d.  WARNING: In the ESC \u201cFull", "below the predetermined speed the system will return to ESC \u201cFull Off\u201d.  WARNING: In the ESC \u201cFull Off\u201d mode, the engine torque reduction and stability features are disabled.  Therefore, enhanced vehicle stability offered by the ESC system is unavailable.  In an emergency evasive maneuver, the ESC system will not engage to assist in maintaining stability.  ESC \u201cFull Off\u201d mode is intended for off-highway or off-road use only.  The Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  ESC cannot prevent all accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  ESC also cannot prevent collisions.  ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light The ESC Activation/Malfunction Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN mode.  It should go out with", "cluster will come on when the ignition is placed in the ON/RUN mode.  It should go out with the engine running.  If the ESC Activation/Malfunction Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC Activation/Malfunction Indicator Light starts to flash as soon as the tires lose traction and the ESC system becomes active.  The ESC Activation/Malfunction Indicator Light also flashes when the Traction Control System (TCS) is active.  If the ESC Activation/Malfunction Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.  Be sure to adapt your speed and driving to the prevailing road conditions.  The ESC OFF Indicator Light", "to adapt your speed and driving to the prevailing road conditions.  The ESC OFF Indicator Light indicates that the Electronic Stability Control (ESC) is in a reduced mode.  Note: The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  Monitoring battery level status led light red 40% or lower yellow 40% to 70% green 70% to 100% electronic stability control (esc) active warning light \u2014 if equipped this warning light will indicate when the electronic stability control system is active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN", "in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.  Adaptive Cruise Control (ACC) Set Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on", "(ACC) Set Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.", "Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash", "If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped", "and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the", "to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.", "Next, link the Uconnect system on your vehicle to Amazon Alexa: With Amazon Alexa, you can connect to your vehicle and remotely access key services and features.  If your vehicle is equipped with Uconnect Navigation, you can send a destination directly to your vehicle using Alexa.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  Pair (link) uconnect phone to a mobile phone \u00b9 use this qr code to access your digital experience.  It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android", "possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.  Uconnect Phone will automatically connect to the highest priority paired phone and/or Audio Device within range.  If you need to choose a particular phone or audio device follow these steps: Press the Media button on the touchscreen to begin.  Change the source to \u201cBluetooth\u00ae\u201d.  Press the Bluetooth\u00ae button on the touchscreen to display the Paired Audio Devices screen.  Press the Add Device button on the touchscreen.  If there is no device currently connected with the system, a pop-up will appear.  Search for available devices on your Bluetooth\u00ae-enabled audio device.  When prompted on the device, confirm the PIN shown on the Uconnect screen.  Uconnect", "audio device.  When prompted on the device, confirm the PIN shown on the Uconnect screen.  Uconnect Phone will display an in-process screen while the system is connecting.  When the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite device.  Selecting \u201cYes\u201d will make this device the highest priority.  This device will take precedence over other paired devices within range.  After connecting to Android Auto\u2122 or Apple CarPlay\u00ae for the first time and undergoing the setup procedure, the smartphone pairs to the Uconnect system via Bluetooth\u00ae without any setup required every time it is within range, if Bluetooth\u00ae is turned on.  Uconnect offers connections via USB, Bluetooth\u00ae, and auxiliary (AUX) ports.  Voice operation is only available for connected USB and AUX devices.  Amazon Alexa Skill \u2014 If Equipped Enjoy the convenience of using your voice to command your vehicle with Amazon Alexa!  With Amazon Alexa, you can connect to your vehicle and", "to command your vehicle with Amazon Alexa!  With Amazon Alexa, you can connect to your vehicle and remotely access key services and features.  If your vehicle is equipped with Uconnect Navigation, you can send a destination directly to your vehicle using Alexa.  If you need assistance, you can always ask alexa for help, or complete a list of commands by saying: \u201calexa, ask <brand name> for help with my car.\u201d here are a few of the many questions you can ask alexa: \u201calexa, ask <vehicle brand> to start my <vehicle name> with your voice code.\u201d \u201calexa, ask <vehicle brand> to lock my <vehicle name> with your voice code.\u201d \u201calexa, ask <vehicle brand> to send 1000 chrysler drive, auburn hills, michigan to my <vehicle name>.\u201d \u201calexa, ask <vehicle brand> what is the fuel level of my <vehicle name>.\u201d an active subscription to siriusxm guardian\u2122 is required.  To use Amazon Alexa, first, register for SiriusXM Guardian\u2122 Next, link the Uconnect system on your vehicle to Amazon Alexa: Download the Amazon Alexa app on your", "link the Uconnect system on your vehicle to Amazon Alexa: Download the Amazon Alexa app on your mobile device (Apple\u00ae or Android\u2122).  Once in the app, tap MENU and go to SKILLS.  Search for <vehicle brand> skill, then tap Enable.  Tap SAVE SETTINGS when prompted.  Link the vehicle brand name to the <vehicle brand> Skill by tapping LINK ACCOUNT.  Log in using your Owner Account credentials.  This will be the same user name and password you used when registering for SiriusXM Guardian\u2122 connected services.  There will be additional settings to confirm on the following screen.  AUTHORIZE the account to return to the <vehicle brand> Skill.  You can now begin using the <vehicle brand> Skill on Alexa!  Amazon Alexa Skill \u2014 If Equipped Enjoy the convenience of using your voice to command your vehicle with Amazon Alexa!  With Amazon Alexa, you can connect to your vehicle and remotely access key services and features.  If your vehicle is equipped with Uconnect Navigation, you can send a destination directly to your", "If your vehicle is equipped with Uconnect Navigation, you can send a destination directly to your vehicle using Alexa.  If you need assistance, you can always ask alexa for help, or complete a list of commands by saying: \u201calexa, ask <brand name> for help with my car.\u201d here are a few of the many questions you can ask alexa: \u201calexa, ask <vehicle brand> to start my <vehicle name> with your voice code.\u201d \u201calexa, ask <vehicle brand> to lock my <vehicle name> with your voice code.\u201d \u201calexa, ask <vehicle brand> to send 1000 chrysler drive, auburn hills, michigan to my <vehicle name>.\u201d \u201calexa, ask <vehicle brand> what is the fuel level of my <vehicle name>.\u201d an active subscription to siriusxm guardian\u2122 is required.  To use Amazon Alexa, first, register for SiriusXM Guardian\u2122 Next, link the Uconnect system on your vehicle to Amazon Alexa: Download the Amazon Alexa app on your mobile device (Apple\u00ae or Android\u2122).  Once in the app, tap MENU and go to SKILLS.  Search for <vehicle brand> skill, then tap Enable.  Tap SAVE", "the app, tap MENU and go to SKILLS.  Search for <vehicle brand> skill, then tap Enable.  Tap SAVE SETTINGS when prompted.  Link the vehicle brand name to the <vehicle brand> Skill by tapping LINK ACCOUNT.  Log in using your Owner Account credentials.  This will be the same user name and password you used when registering for SiriusXM Guardian\u2122 connected services.  There will be additional settings to confirm on the following screen.  AUTHORIZE the account to return to the <vehicle brand> Skill.  You can now begin using the <vehicle brand> Skill on Alexa!  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that", "media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.  Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Radio Voice", "You can check which smartphones are compatible at g.co/androidauto/requirements.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.", "Window Lockout Switch The window lockout switch allows you to disable the window controls on the rear passenger doors.  To disable the window controls, rotate the switch downward.  To enable the window controls, rotate the switch upward.  Child-Protection Door Lock System \u2014 Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove the sealing plug for access, and use a flat-blade screwdriver (or mechanical key) to rotate the dial to the lock or unlock position.  Note: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test", "it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Note: Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  Auto-Down Feature The driver door power window switch and the front passenger door power window", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.", "Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  Cleaning the trailcam the trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD", "the button is released.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.", "With the vehicle rolling at 1 to 3 mph (2 to 5 km/h), shift an automatic transmission into NEUTRAL (N), or press the clutch pedal on a manual transmission.  While the vehicle is coasting at 1 to 3 mph (2 to 5 km/h), shift the transfer case lever firmly to the desired position.  Do not pause with the transfer case in N (Neutral).  Once the shift is completed, place the automatic transmission into DRIVE or release the clutch pedal on a manual transmission.  Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  Apply the parking brake, place the gear selector in NEUTRAL, and press the clutch pedal before starting the vehicle.  This vehicle is equipped with a clutch interlocking ignition system.  It will not start unless the clutch pedal is pressed to the floor.  To Turn On The Engine Using The ENGINE START/STOP Button The transmission must be in PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.", "PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage automatically after 10 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP", "Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in", "lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).", "Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with", "vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not", "you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does", "will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could", "slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will", "the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M", "battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.", "In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  Intentional tampering with emissions control systems can result in civil penalties being assessed against you.  Please read and follow these safety precautions.  Failure to do so may result in injury or property damage.", "and follow these safety precautions.  Failure to do so may result in injury or property damage.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer", "be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale", "emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  Your vehicle is required to have an OBD II and a connection port to allow access to information related to the", "is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the", "battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  For normal service, periodic fluid level checks are not required.  When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected.  If gear oil leakage is suspected, inspect the fluid level.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government", "excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Intentional tampering with emissions control systems can result in civil penalties being assessed against you.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too", "gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat,", "the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating,", "off immediately and call for service.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as", "the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this", "light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to", "before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants", "wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking", "equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the", "contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting", "which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.  Note: Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle while making connections.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source", "personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the", "brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could", "vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.", "Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts", "Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow", "the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down", "nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.", "the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive", "the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose", "If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.", "If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offIf the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and", "steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate", "Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  This warning light will turn on when there's a fault with the EPS system The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an", "displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d This warning light will turn on when there's a fault", "Please contact an authorized dealer.\u201d This warning light will turn on when there's a fault with the EPS system When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  Push the SWAY BAR switch to disconnect or connect the sway bar.", "applying the brakes autonomously.  Push the SWAY BAR switch to disconnect or connect the sway bar.  The Sway Bar Indicator Light (located in the instrument cluster) will illuminate when the bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when activation conditions are not met.  The stabilizer/sway bar should remain in on-road mode during normal driving conditions.  The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.  If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering", "maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offThe heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel", "has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Press the heated steering wheel button once to turn the heating element on.  Press", "cause a fire.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  When the SET (+) or the SET (-) button (located on the steering wheel) is pushed, the display will read \u201cACC SET.\u201d The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.", "Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately \"\u21e8air bag warning light\" .  Air Bag Warning Light The Occupant Restraint Controller (ORC) monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position.  If the ignition switch is in the OFF position or in the ACC position, the air bag system is not on and the air bags will not inflate.  The ORC contains a backup power supply system that may", "not on and the air bags will not inflate.  The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or it becomes disconnected prior to deployment.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is detected that could affect the air bag system.  The diagnostics also record the nature of the malfunction.  While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer", "is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  Note: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled.  In this condition the air bags may not be ready to inflate for your protection.  have an authorized dealer service the air bag system immediately.  WARNING: Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive,", "ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Air Bag Warning Light This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with", "when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  Air Bag Warning Light The Occupant Restraint Controller (ORC) monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position.  If the ignition switch is in the OFF position or in the ACC position, the air bag system is not on and the air bags will not inflate.  The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or it becomes disconnected prior to deployment.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN", "four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is detected that could affect the air bag system.  The diagnostics also record the nature of the malfunction.  While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on", "Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  Note: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled.  In this condition the air bags may not be ready to inflate for your protection.  have an authorized dealer service the air bag system immediately.  WARNING: Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.", "Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  Who is Covered You are covered by Roadside Assistance services if you are a purchaser for use of the vehicle.  Roadside Assistance services last for five years or 60,000 miles on the odometer, whichever occurs first, calculated from the start date of the Basic Limited Warranty, as set forth in your Warranty Information book.  1 1.  Towing services provided through Cross Country Motor Club, Inc.Medford, MA 02155, except in AK,CA, HI, OR, WI, and WY, where services are provided by Cross Country Motor Club of California, Inc., Thousand Oaks, CA 91360.  Who is Covered You are covered by Roadside Assistance", "California, Inc., Thousand Oaks, CA 91360.  Who is Covered You are covered by Roadside Assistance services if you are a purchaser for use of the vehicle.  Roadside Assistance services last for five years or 60,000 miles on the odometer, whichever occurs first, calculated from the start date of the Basic Limited Warranty, as set forth in your Warranty Information book.  1 1.  Towing services provided through Cross Country Motor Club, Inc. Medford, MA 02155, except in AK,CA, HI, OR, WI, and WY, where services are provided by Cross Country Motor Club of California, Inc., Thousand Oaks, CA 91360.", "If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.", "tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for", "Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  SOS Call \u2014 If Equipped WARNING: Some SiriusXM Guardian\u2122 connected services, including SOS Call and Roadside Assistance Call, will NOT work without a network connection compatible with your device.", "Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.", "the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the", "rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.", "Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a", "electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of", "and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the", "the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.", "Automatic Transmission \u2014 If Equipped  Automatic Transmission \u2014 If Equipped Select the DRIVE range when towing.  The transmission controls include a drive strategy to avoid frequent shifting when towing.  However, if frequent shifting does occur while in DRIVE, you can use the AutoStick shift control to manually select a lower gear.  Note: Using a lower gear while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  This action will also provide better engine braking.  Component Fluid, Lubricant, or Genuine Part Automatic Transmission \u2013 If Equipped Use only Mopar\u00ae ZF 8 & 9 Speed ATF Automatic Transmission Fluid or equivalent.  Failure to use the correct fluid may affect the function or performance of your transmission.  Manual Transmission \u2013 If Equipped We recommend using Mopar\u00ae ATF+4 Automatic Transmission Fluid.  Transfer Case We recommend using Mopar\u00ae ATF+4 Automatic Transmission Fluid.  Front Axle", "Fluid.  Transfer Case We recommend using Mopar\u00ae ATF+4 Automatic Transmission Fluid.  Front Axle Differential We recommend using Mopar\u00ae Gear & Axle Lubricant (SAE 75W85) (API GL-5).  Rear Axle Differential (M220 Sales Codes DRE/DRF) We recommend using Mopar\u00ae Gear & Axle Lubricant (SAE 75W85) (API GL-5).  Models equipped with Trac-Lok Limited Slip Differential require a friction modifier additive.  Brake Master Cylinder We recommend using Mopar\u00ae DOT 3 Brake Fluid, SAE J1703.  Power Steering Reservoir We recommend using Mopar\u00ae Electric Steering Pump Fluid.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.", "to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed", "95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire if a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have", "for this tire if a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: the gvwr is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire", "in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 What is the phone number for roadside assistance call?  The phone number is: US: 1-800-521-2779 Canada: 1-800-363-4869 If I am subscribed to SiriusXM Guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance?  No, however your new vehicle may include Roadside Assistance Call services.  Setting Name Description Voice Response Length This setting will change the response length for the Voice Recognition system.  The \u201cBrief\u201d setting provides a shortened audio description from the system.  The \u201cDetailed\u201d setting provides the full audio description from the system.  Show Command List This setting will allow you to turn the Command List on or off.  The \u201cAlways\u201d setting will always show the Command List.  The \u201cWith Help\u201d", "Command List on or off.  The \u201cAlways\u201d setting will always show the Command List.  The \u201cWith Help\u201d setting will show the Command List and provide a brief description of what the command does.  The \u201cNever\u201d setting will turn the Command List off.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the", "vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure", "it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always", "inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children", "in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on", "or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the", "location accessible to children.  A child could operate power windows, other controls, or move the vehicle.", "Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or", "with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of", "and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match", "Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl", "or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the", "driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Engine start-up in very low ambient temperature could result in evident white smoke.", "previously.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the", "This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin", "low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Conditions that will cause the engine to start automatically while in autostop mode: the transmission selector is moved out of drive to maintain cabin temperature comfort", "mode: the transmission selector is moved out of drive to maintain cabin temperature comfort actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode hvac system temperature or fan speed is manually adjusted battery voltage drops too low stop/start off switch is pushed a stop/start system error occurs stop/start autostop active time exceeds five minutes transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service", "is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors", "a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software,", "into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.", "will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Jack Location The jack and tools are stored under the right rear seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools", "seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat.  Removing the wing bolt release the tool bag straps from the jack and remove tools from bag.  Jack and tool bag remove tool kit and assemble tools.  Jack And Tool Bag There are two ways to assemble the tools: Note: If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  CAUTION: The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools, always reinstall them in the original carrier and location.  While", "After using the jack and tools, always reinstall them in the original carrier and location.  While driving you may experience abrupt stopping, rapid acceleration or sharp turns.  A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.", "UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  Volume & On/Off Control Push the VOLUME & On/Off control knob to turn on", "on the Uconnect system.  Volume & On/Off Control Push the VOLUME & On/Off control knob to turn on and off the Uconnect system.  The electronic volume control turns continuously (360 degrees) in either direction, without stopping.  Turning the VOLUME & On/Off control knob clockwise increases the volume, and counterclockwise decreases it.  When the audio system is turned on, the sound will be set at the same volume level as last played.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to", "setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.", "Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or", "with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of", "and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match", "Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl", "or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.", "4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together,", "the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any", "drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  When To Use 4L Range When off-road driving, shift into 4L for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low speed pulling power.  This range should be limited to extreme situations such as deep snow, mud, steep inclines, or sand where additional low speed pulling power is needed.  Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4L range.  CAUTION: Do not use 4L range when operating the vehicle on dry pavement.  Driveline hardware damage can result.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft,", "\u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive,", "into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.", "BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load", "cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There", "EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed", "cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  Lower Anchors And Tethers For CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the", "belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.", "Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical", "illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.  It may cause burns even at low temperatures, especially if used for long periods of time.  Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion.  This may cause the seat heater to overheat.  Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  The engine must be running for the heated steering wheel to operate.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle", "Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme", "HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating", "screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the", "your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  When Remote Start is activated, the front and rear defrost will", "screen of the touchscreen.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The engine must be running for the heated steering wheel to operate.", "SiriusXM Guardian\u2122 In-Vehicle Assistance Features \u2014 If Equipped With SiriusXM Guardian\u2122, your vehicle has onboard assistance features located on the rearview mirror or overhead console designed to enhance your driving experience if you should ever need assistance or support.  SiriusXM Guardian\u2122 In-Vehicle Assistance Features With SiriusXM Guardian\u2122, your vehicle has onboard assistance features located on the rearview mirror or overhead console designed to enhance your driving experience if you should ever need assistance or support.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  INSTRUMENT CLUSTER DISPLAY Your vehicle", "the lower storage compartment, lift the bottom latch.  INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.", "When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route", "ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no", "to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  Mud Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get", "debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any", "The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These", "to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it", "for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen", "display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are", "Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center", "or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature", "to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Opening The Hood Release both of the outside hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood", "hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Note: Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If", "of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.", "Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather.  To clear the windows, select Defrost or Mix mode and increase the front blower speed.  Do not use the Recirculation mode without A/C for long periods, as fogging may occur.  Winter Operation To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used.  Use of the Air Recirculation mode during Winter months is not recommended, because it may cause window fogging.  Do not use abrasive cleaning components, solvents, steel wool, or other aggressive material to clean the lenses.  The lenses in front of the instruments in this vehicle are molded in clear plastic.  When cleaning the lenses, care must be taken to avoid scratching the plastic.  Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.  Do not press the touchscreen with any hard", "different lens cleaning procedures must be followed.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsTo minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.  To remove road dirt, wash with a mild soap solution followed by rinsing.  If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the", "the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  If the \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the windshield and forward-facing camera inspected at an authorized dealer.  All glass surfaces should be cleaned on a regular basis with Mopar\u00ae Glass Cleaner, or any commercial household-type glass cleaner.  Never use an abrasive type cleaner.  Use caution when cleaning the inside rear window equipped with electric defrosters or windows equipped with radio antennas.  Do not use scrapers or other sharp instruments that may scratch the elements.  The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems are experienced.  This inspection should include the following points:", "The engine is allowed to crank as long as 25 seconds.  If the engine fails to start during this period, please wait at least two minutes for the starter to cool before repeating start procedure.  If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filters to avoid engine damageInstall a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible", "pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damageThe system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  The transmission must be in PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage", "once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage automatically after 10 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Extended Park Starting Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Note: Extended Park condition occurs when the vehicle has not been started or driven for at least 30 days.  CAUTION: To prevent damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15", "damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  If Engine Fails To Start If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  WARNING: Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the", "equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly CAUTION: To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.", "Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  All cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  (1) Locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.\u201d on your vehicle's placard.  Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing", "or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.", "Phone & Bluetooth\u00ae Pairing A feature of the Jeep\u00ae wireless speaker is the ability for the Jeep\u00ae wireless speaker to connect to devices using Bluetooth\u00ae.  Follow these simple steps to connect a Bluetooth\u00ae-enabled device to the Jeep\u00ae wireless speaker: Press and hold the power button for 2-3 seconds to turn the Jeep\u00ae wireless speaker on.  Turn \u201con\u201d Bluetooth\u00ae for the device you desire to be connected to the Jeep\u00ae wireless speaker.  For instructions on how to turn on and off Bluetooth\u00ae settings for the desired device, refer to the device\u2019s user manual.  When powered on, the Jeep\u00ae wireless speaker will automatically enter pairing mode.  To pair a second device, press and hold the Bluetooth\u00ae button for 2-3 seconds, until an audio cue is heard.  Then go to the devices\u2019 Bluetooth\u00ae settings and select \u201cJeep\u00ae Speaker\u201d from the list.  The Jeep\u00ae wireless speaker will remember the last eight devices it has paired with.  Note: If the Jeep\u00ae wireless speaker is left on with an inactive Bluetooth\u00ae connection for 30 minutes,", "If the Jeep\u00ae wireless speaker is left on with an inactive Bluetooth\u00ae connection for 30 minutes, it will automatically turn off.  The Jeep\u00ae wireless speaker can be turned on again by pressing and holding the power button for 2-3 seconds.  Press the settings button on the touchscreen.  Press the paired phones or audio sources button.  Press to select the particular phone or the particular audio device.  A pop-up menu will appear; press \u201cConnect Phone\u201d.  Press the X to exit out of the Settings screen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The MAX A/C button is only", "will allow you to toggle up or down through the available settings.  The MAX A/C button is only available on the touchscreen.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsThe SYNC button is only available on the touchscreen.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first", "or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Press the Phone button.  Press the Dial/Keypad button on the touchscreen.  The Touch-Tone screen will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press \u201cDial/Call\u201d.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  Overview Bluetooth\u00ae Streaming Audio or Bluetooth\u00ae Mode is entered by pairing a Bluetooth\u00ae device, containing music, to the Uconnect system.  Before proceeding, the Bluetooth\u00ae device must be paired to the Uconnect Phone to communicate with the Uconnect system.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under", "To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).", "If there is a set speed in memory push the RES (resume) button and then remove your foot from the accelerator pedal.  The instrument cluster display will display the last set speed.  The MAX A/C button is only available on the touchscreen.  The vr button is used to activate/deactivate your voice recognition system.  1 \u2014 All Button 2 \u2014 Presets Button 3 \u2014 Favorites Button 4 \u2014 Game Zone Button 1 \u2014 Radio Button 5 \u2014 Controls Button 2 \u2014 Media Button 6 \u2014 Phone Button 3 \u2014 Climate Button 7 \u2014 Settings Button 4 \u2014 Apps Button  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are", "1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic modeWhen Seats & Comfort/Auto-On Comfort Systems button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s comfort", "is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s comfort systems when remote start has been activated or the vehicle has been started.  Note: depending on the vehicle\u2019s options, feature settings may vary.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons", "When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts,", "an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your", "corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Only use the positive battery post on the main battery to jump start", "see an authorized dealer.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large", "when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  The positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.", "Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  What to Do If your vehicle requires jump start assistance, out of gas/fuel delivery, tire service, lockout service or towing as a result of a mechanical breakdown, dial toll-free: USA: 1-800-521-2779/Canada: 1-800-363-4869.  Provide your name, Vehicle Identification Number (VIN) required for covered services, license plate number, and your location, including the telephone number from which you are calling.  Briefly describe the nature of the problem and answer a few simple questions.  You will be given the name of the service provider and an estimated time of arrival.  If you feel you are in an unsafe", "name of the service provider and an estimated time of arrival.  If you feel you are in an unsafe situation, please let us know.  With your consent, we will contact local police or safety authorities.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10", "to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in", "battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.", "Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that", "media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app", "If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.", "Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 android", "smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in", "your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on", "calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.", "buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once", "and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect", "data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.  Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you", "data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 And Apple CarPlay\u00ae Automatic Bluetooth\u00ae Pairing After connecting to Android Auto\u2122 or Apple CarPlay\u00ae for the first time and undergoing the setup procedure, the smartphone pairs to the Uconnect system via Bluetooth\u00ae without any setup required every time it is within range, if Bluetooth\u00ae is turned on.  Note: Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.", "The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring Height (H) Attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the", "approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  Service Forward Collision Warning (FCW) Light \u2014 If Equipped This warning light will illuminate to indicate a fault in the Forward Collision Warning System.", "This warning light will illuminate to indicate a fault in the Forward Collision Warning System.  Contact an authorized dealer for service Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.", "Recommended Distribution Hitch Adjustment Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring height (h) attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing", "for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  Recommended Distribution Hitch Adjustment Position the truck to be ready to connect to the trailer (do not connect the trailer).", "Adjustment Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring height (h) attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Recommended Distribution Hitch Adjustment An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.", "Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.  The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window", "switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  Power Window Switches Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.  Window Lockout Switch The window lockout switch allows you to disable the window controls on the rear passenger doors.  To disable the window controls, rotate the switch", "the window controls on the rear passenger doors.  To disable the window controls, rotate the switch downward.  To enable the window controls, rotate the switch upward.", "PARKING BRAKE Before exiting the vehicle, make sure that the parking brake is fully applied.  Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or FIRST gear.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic", "to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  WARNING: Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake", "be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  CAUTION: If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as", "lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  Always secure your vehicle by fully applying the parking", "brake and make sure the ignition is OFF.  Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a", "your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle", "Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Trailer And Tongue Weight Never exceed the maximum tongue weight stamped on your bumper or trailer hitch.  Consider the following items when computing the weight on the rear axle of the vehicle: the tongue weight of the trailer the weight of any other type of cargo or equipment put in or on your vehicle the weight of the driver and all passengers note: remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is", "weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a", "If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.", "Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be", "Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire dealer or original", "those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result", "what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw", "accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the", "take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Preparations For Jacking Park on a firm, level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  Turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers", "if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers should not remain in the vehicle when the vehicle is being jacked in position.", "Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water Flowing water can be extremely dangerous.  Never attempt to cross a fast running stream or river even in shallow water.  Fast moving water can easily push your vehicle downstream, sweeping it out of control.  Even in very shallow water, a high current can still wash the dirt out from around your tires putting you and your vehicle in jeopardy.  There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the vehicle's running ground clearance.  You should never attempt to cross flowing water which is deeper than the vehicle's running ground clearance.  Even the slowest current can push the heaviest vehicle downstream and out of control if the water is deep enough to push on the large surface area of the vehicle's body.  Before you proceed, determine the speed of the current, the water's depth, approach angle, bottom condition and if there are any obstacles.  Then cross at an angle heading", "approach angle, bottom condition and if there are any obstacles.  Then cross at an angle heading slightly upstream using the low and slow technique.  WARNING: Never drive through fast moving deep water.  It can push your vehicle downstream, sweeping it out of control.  This could put you and your passengers at risk of injury or drowning.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible", "and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around", "along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water Flowing water can be extremely dangerous.  Never attempt to cross a fast running stream or river even in shallow water.  Fast moving water can easily push your vehicle downstream, sweeping it out of control.  Even in very shallow water, a high current can still wash the dirt out from around your tires putting you and your vehicle in jeopardy.  There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the vehicle's running ground clearance.  You should never attempt to cross flowing water which is deeper than the vehicle's running ground clearance.  Even the slowest current can push the heaviest vehicle downstream and out of control if the water is deep enough to push on the large", "the heaviest vehicle downstream and out of control if the water is deep enough to push on the large surface area of the vehicle's body.  Before you proceed, determine the speed of the current, the water's depth, approach angle, bottom condition and if there are any obstacles.  Then cross at an angle heading slightly upstream using the low and slow technique.  WARNING: Never drive through fast moving deep water.  It can push your vehicle downstream, sweeping it out of control.  This could put you and your passengers at risk of injury or drowning.  Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep", "recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less", "permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when", "will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.", "Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently", "ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  VEHICLE MODIFICATIONS/ALTERATIONS WARNING: Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in", "methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred", "Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the", "fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).", "While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  Do not use in hilly terrain or with heavy loads.  When using the Cruise Control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.  Use Cruise Control in flat terrain and with light loads to maximize fuel efficiency.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d  While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate", "speed.  Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  To Accelerate For Passing While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.", "4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together,", "the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any", "drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H", "rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.", "each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  2H (Two-Wheel Drive High Range) 4H (Four-Wheel Drive High Range) N (Neutral) 4L (Four-Wheel Drive Low Range) In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal", "4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L", "Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d", "and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.", "of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear", "Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as", "bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and", "up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up", "the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear", "can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.", "Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the", "start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation", "in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd", "and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start", "10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M", "during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.", "Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard Top Panel(s) Storage Bag \u2014", "that are used when the hard top is not installed on the vehicle.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top", "the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or", "vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure", "the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the", "in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric", "with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.", "The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  Based on engine operation conditions, the oil change", "possible, within the next 500 miles (805 km).  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  The engine oil filter should be replaced with a new filter at every engine oil change.  A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator", "has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that", "display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.", "Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the", "form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background", "for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold", "cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by", "the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Get started the", "have incoming text messages read out loud, and place and receive hands-free calls.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.", "For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  See Engine Fluids and Lubricants for the correct engine oil viscositySynthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Lubricant should be approximately 1/8 inch (3 mm) below the bottom edge of the oil fill hole.  Use only the manufacturer\u2019s recommended fluid Trac-Lok is especially helpful during slippery driving conditions.  With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction.  Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure", "may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure build-up or your tire pressure will be too low.  1 \u2014 Coolant Temperature 2 \u2014 Oil Temperature 3 \u2014 Battery Voltage 4 \u2014 Transmission Temperature 5 \u2014 Oil Pressure Operation in ambient temperature below 32\u00b0F (0\u00b0C) may require special considerations.  The following charts suggest these options:  Use only the manufacturer\u2019s recommended fluid For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Selection Of Lubricant Use only the manufacturer\u2019s recommended fluid Selection Of Lubricant It is important to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only", "to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only manufacturer's specified transmission fluid It is important to maintain the transmission fluid at the correct level using the recommended fluid.  Note: No chemical flushes should be used in any transmission; only the approved lubricant should be used.  CAUTION: Using a transmission fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder Selection Of Lubricant Use only manufacturer's recommended manual transmission fluid", "Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather.  To clear the windows, select Defrost or Mix mode and increase the front blower speed.  Do not use the Recirculation mode without A/C for long periods, as fogging may occur.  Do not use abrasive cleaning components, solvents, steel wool, or other aggressive material to clean the lenses.  The lenses in front of the instruments in this vehicle are molded in clear plastic.  When cleaning the lenses, care must be taken to avoid scratching the plastic.  Plastic is not as scratch", "cleaning the lenses, care must be taken to avoid scratching the plastic.  Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsTo minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.  To remove road dirt, wash with a mild soap solution followed by rinsing.  If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not", "builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  If the \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the windshield and forward-facing camera inspected at an authorized dealer.  All glass surfaces should be cleaned on a regular basis with Mopar\u00ae Glass Cleaner, or any commercial household-type glass cleaner.  Never use an abrasive type cleaner.  Use caution when cleaning the inside rear window equipped with electric defrosters or windows equipped with radio antennas.  Do not use scrapers or other sharp instruments that may scratch the elements.  The wiper blades and wiper arms should be inspected periodically, not just when wiper performance", "The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems are experienced.  This inspection should include the following points:", "For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  See Engine Fluids and Lubricants for the correct engine oil viscositySynthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Lubricant should be approximately 1/8 inch (3 mm) below the bottom edge of the oil fill hole.  Use only the manufacturer\u2019s recommended fluid Trac-Lok is especially helpful during slippery driving conditions.  With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction.  Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure", "may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure build-up or your tire pressure will be too low.  1 \u2014 Coolant Temperature 2 \u2014 Oil Temperature 3 \u2014 Battery Voltage 4 \u2014 Transmission Temperature 5 \u2014 Oil Pressure Operation in ambient temperature below 32\u00b0F (0\u00b0C) may require special considerations.  The following charts suggest these options:  Use only the manufacturer\u2019s recommended fluid For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Synthetic Engine Oils Your engine was designed for synthetic engine oils, only use synthetic API approved engine oils.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE", "oils.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Engine Oil Usage See Engine Fluids and Lubricants for the correct engine oil viscosityOil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in", "operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.", "Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and", "should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers", "steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.", "Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road", "lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5", "fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a", "Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front", "on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water", "door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Door Frame Installation Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten fasteners target torque specification for torx fasteners maximum minimum 44.2 in-lb (5 n\u00b7m) 53.1 in-lb (6 n\u00b7m) 35.4 in-lb (4 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top", "strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step five step five insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.", "Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note:", "reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow", "is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.", "VEHICLE IDENTIFICATION NUMBER (VIN) The VIN is found on the left front corner of the A-pillar, visible from outside of the vehicle through the windshield.  Note: It is illegal to remove or alter the VIN plate.  Vehicle Identification Number Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.  Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle", "driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.", "Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the", "windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the", "EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button", "drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the", "Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may", "transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be", "the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeHow long does it take to remotely start my vehicle?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle", "or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will remote start your vehicle more quickly.  However its range is limited.  For example, when you are leaving the stadium after the game, you can use the Vehicle Branded App to remote start your vehicle and have the inside of your vehicle comfortable by the time you get to it.  Will my vehicle be safe if I lose my wireless device?  People sometimes lose their wireless devices, which is why security measures have been engineered into the Vehicle Branded App.  Asking for your username, password and SiriusXM Guardian\u2122 Security PIN help to ensure that nobody can start your vehicle if they happen to find your device.  Can someone drive off with my vehicle using the App?  nob Driving your vehicle still requires the keys to be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the interior before you arrive.  Can I stop a vehicle that is being driven", "to warm up or cool down the interior before you arrive.  Can I stop a vehicle that is being driven with the cancel Remote Vehicle Start command?  nob If the vehicle is in motion, the cancel Remote Vehicle Start button will not stop the vehicle.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "To engage REVERSE gear from the NEUTRAL position, lift the REVERSE ring, located below the knob and move the gear selector all the way left and then forward.  If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  To shift the gears, fully press the clutch pedal and place the gear selector into the desired gear position (the diagram for the engagement of the gears is displayed on the handle of the selector).  The gear position will be displayed in the instrument cluster.  Operation To activate AutoStick mode, move the gear selector into the MANUAL (M) position (beside the DRIVE position).  The current transmission gear will be displayed in the instrument cluster.  In AutoStick mode,", "The current transmission gear will be displayed in the instrument cluster.  In AutoStick mode, you can use the gear selector (in the MANUAL position) to manually shift the transmission.  Tapping the gear selector forward (-) while in the MANUAL (M) position will downshift the transmission to the next lower gear.  Tapping the selector rearward (+) will command an upshift.  In AutoStick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result.  It will remain in the selected gear until another upshift or downshift is chosen, except as follows: The transmission will automatically downshift as the vehicle slows (to prevent engine lugging) and will display the current gear.  The transmission will automatically downshift to FIRST gear when coming to a stop.  After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or", "as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or THIRD gear, in 4L range).  Tapping (+) (at a stop) will allow starting in SECOND gear.  Starting out in SECOND or THIRD gear can be helpful in snowy or icy conditions.  If a requested downshift would cause the engine to overspeed, that shift will not occur.  The system will ignore attempts to upshift at too low of a vehicle speed.  Holding the gear selector in the (-) position will downshift the transmission to the lowest gear possible at the current speed.  Transmission shifting will be more noticeable when AutoStick is enabled.  The system may revert to automatic shift mode if a fault or overheat condition is detected.  To disengage AutoStick mode, return the gear selector to the DRIVE position.  You can shift in or out of the AutoStick position at any time without taking your foot off the accelerator pedal.  Note: When Hill Descent Control is enabled, AutoStick is not active.  WARNING: Do not downshift for", "Note: When Hill Descent Control is enabled, AutoStick is not active.  WARNING: Do not downshift for additional engine braking on a slippery surface.  The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury.  PARK (P) This range supplements the parking brake by locking the transmission.  The engine can be started in this range.  Never attempt to use PARK while the vehicle is in motion.  Apply the parking brake when exiting the vehicle in this range.  When parking on a hill, apply the parking brake before shifting the transmission to PARK.  As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  When exiting the vehicle, always: apply the parking brake shift the transmission into park turn the ignition off remove the key fob from the vehicle the following indicators should be used to ensure that you have properly engaged the transmission into the park position: when shifting into park, push", "you have properly engaged the transmission into the park position: when shifting into park, push the lock button on the gear selector and firmly move the gear selector all the way forward until it stops and is fully seated.  Look at the transmission gear position display and verify that it indicates the PARK position (P), and is not blinking.  With the brake pedal released, verify that the gear selector will not move out of PARK.  Note: On four-wheel drive vehicles, be sure that the transfer case is in a drive position.  WARNING: Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle", "is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the", "the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  CAUTION: Before moving", "A child could operate power windows, other controls, or move the vehicle.  CAUTION: Before moving the transmission gear selector out of PARK, you must start the engine, and also press the brake pedal.  Otherwise, damage to the gear selector could result.  DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to", "will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Hazard Warning Flashers Button The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the", "or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Warning CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks 1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal", "contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.", "Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to", "Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Depending on the vehicle\u2019s options, feature settings may vary.  Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Depending on the vehicle\u2019s options, feature settings may vary.  When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Note: depending on the vehicle\u2019s options, feature settings may vary.  Adjustable Chime Volume Settings The Front and Rear chime volume settings are programmable.  The settings may be programmed through the Uconnect system The chime volume", "are programmable.  The settings may be programmed through the Uconnect system The chime volume settings include low, medium, and high.  The factory default volume setting is medium.  ParkSense will retain its last known configuration state through ignition cycles.  When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Note: depending on the vehicle\u2019s options, feature settings may vary.", "Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal", "km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed", "is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  Manual Activation Of The Rear View Camera  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is", "Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the", "on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You", "for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be", "the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE,", "the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying", "this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced", "a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that", "Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.", "TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles", "a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension", "may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled", "using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension", "may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged,", "must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be", "Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.", "Sos call system limitations vehicles sold in mexico do not have sos call system capabilities.  SOS or other emergency line operators in Mexico may not answer or respond to SOS system calls.  If the SOS Call system detects a malfunction, any of the following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d an in-vehicle audio message will state \u201cvehicle device requires service.  Please contact an authorized dealer.\u201d even if the sos call system is fully functional, factors beyond fca us llc\u2019s control may prevent or stop the sos call system operation.  These include, but are not limited to, the following factors: the ignition is in the off position the vehicle\u2019s electrical systems are not intact the sos call system software and/or hardware are damaged", "electrical systems are not intact the sos call system software and/or hardware are damaged during a crash the vehicle battery loses power or becomes disconnected during a vehicle crash lte (voice/data) or 4g (data) network and/or global positioning satellite signals are unavailable or obstructed equipment malfunction at the sos operator facility operator error by the sos operator lte (voice/data) or 4g (data) network congestion weather buildings, structures, geographic terrain, or tunnels warning: ignoring the rearview mirror light could mean you will not have sos call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  WARNING: ALWAYS obey traffic laws and", "service the Occupant Restraint Control system immediately.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber.  Never place anything on or near the vehicle\u2019s LTE (voice/data) or 4G (data) and GPS antennas.  You could prevent LTE (voice/data) or 4G (data) and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable LTE (voice/data) or 4G (data) network connection and a GPS signal is required for the SOS Call system to function properly.  Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to", "not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important", "the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine", "SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception,", "operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be", "part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside", "ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all", "preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls,", "Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a", "brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear", "fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.", "Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This", "does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the", "and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Synthetic Engine Oils Your engine was designed for synthetic engine oils, only use synthetic API approved engine oils.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.", "CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or", "vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is", "Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.", "The ignition switch must be in the ACC or ON/RUN position to adjust the power mirrors.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the", "unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP", "is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note:", "to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel", "parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the", "to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer", "doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).", "Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to", "equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is", "how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.", "Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Drag & Drop Menu Bar The Uconnect features and services in the main menu bar are easily customized for your preference.", "The Uconnect features and services in the main menu bar are easily customized for your preference.  Simply follow these steps: press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Note: This feature is only available if the vehicle is in PARK.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the", "to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the", "select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF", "one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the", "equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power", "equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Key Left Vehicle Feature If a valid key fob is no longer detected inside the vehicle while the vehicle\u2019s ignition system is in the ON/RUN or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument cluster display along with an interior chime.  An exterior audible and visual alert will also be activated to warn the driver.  The vehicle\u2019s horn will rapidly chirp three times along with a single flash of the vehicle\u2019s exterior lights.  Note: The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  Front door removal front door removal \u00b9 use this qr code to access your digital experience.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted", "doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  To remove the front doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nut from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin located under the rear seat.  Hinge pin nut remove the plastic wiring access door under the instrument panel by sliding the plastic panel along the door frame toward the seats until the tabs are detached.  Wiring access door note: do not force open; this will break the plastic cover.  Pull up on the red locking tab to unlock the wiring harness.  Closed wiring harness 1 \u2014 red locking tab 2 \u2014 wiring harness lever (closed position) push and hold down the black security tab under the wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014 wiring", "wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014 wiring harness lever (open position) 2 \u2014 black security tab with the wiring harness open, pull straight downward on the wiring connector to unplug.  Store the wiring connector in the lower door basket.  With the door in the open position, remove the check screw from the door check attachment on the body side (using a #T40 Torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  See note below if the check arm gets pushed into the door while the door is off.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.", "operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Note: When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the", "Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "US/CANADA Exposure to Radio Frequency Radiation The radiated output power of the internal wireless radio is far below the FCC and IC radio frequency exposure limits.  Nevertheless, the wireless radio will be used in such a manner that the radio is 8 inches (20 cm) or further from the human body.  The internal wireless radio operates within guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community.  The radio manufacturer believes the internal wireless radio is safe for use by consumers.  The level of energy emitted is far less than the electromagnetic energy emitted by wireless devices such as mobile phones.  However, the use of wireless radios may be restricted in some situations or environments, such as aboard airplanes.  If you are unsure of restrictions, you are encouraged to ask for authorization before turning on the wireless radio \"\u21e8general information\" .  Connected Vehicles Privacy of any wireless and wired communications cannot", "information\" .  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to", "equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.", "As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Connected Vehicles Privacy of any", "the Vehicle Security Light in the instrument cluster will flash.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.", "Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:  ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will", "START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.", "that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).", "Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety", "any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province,", "including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where", "Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html frequently asked questions about installing child restraints with seat belts what is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child", "anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward-facing child restraint, up to the recommended weight limit of the child restraint.  Can the rear-facing child restraint touch the back of the front passenger seat?  Yes contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.  Can the rear head restraints be removed?  Yes the center head restraint can be removed if it interferes with the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint?  No do not twist the buckle stalk in a seating position with an alr retractor.  Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the", "and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.  Use this simple 5-step test to decide whether the child can use the vehicle\u2019s seat belt alone: Can the child sit all the way back against the back of the vehicle seat?  Do the child\u2019s knees bend comfortably over the front of the vehicle seat while the child is still sitting all the way back?  Does the shoulder belt cross the child\u2019s shoulder between the neck and arm?  Is the lap part of the belt as low as possible, touching the child\u2019s thighs and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to any of these questions was \u201cno,\u201d then the child still needs to use a booster seat in this vehicle.  If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s squirming or slouching can move the belt out of position.  If the shoulder belt contacts the", "squirming or slouching can move the belt out of position.  If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.  WARNING: Never allow a child to put the shoulder belt under an arm or behind their back.  In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.  A child must always wear both the lap and shoulder portions of the seat belt correctly.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.", "is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL", "fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is", "center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Warm up the engine before", "vehicle's obd ii system is ready and you can proceed to the i/m station.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds", "do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.", "Door Frame Installation Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten fasteners target torque specification for torx fasteners maximum minimum 44.2 in-lb (5 n\u00b7m) 53.1 in-lb (6 n\u00b7m) 35.4 in-lb (4 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of", "door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step five step five insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  To remove the half-doors, repeat the installation steps in reverse order.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to", "from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate", "not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  If the check arm is stuck inside the door, follow these instructions to install the check arm.  To reinstall the door(s), perform the previous steps in the reverse order.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  To install the front door exterior mirrors on the half-doors, proceed as follows: To install the front or rear half-doors, proceed as follows: Locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place Tool Into Service Hole Of Plug To Remove Using the tool, slowly pull upwards from the center of the plug to remove.  Upon first", "To Remove Using the tool, slowly pull upwards from the center of the plug to remove.  Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  Only adjust the door to fit correctly against the striker.  DO NOT adjust the striker, as this could affect the positioning of the full door.  Half-Door Installation To install the front or rear half-doors, proceed as follows: Remove the full doors from the vehicle.  For front door removal, see For rear door removal, see Locate the upper and lower hinge pins on the lower half-door, and lower them into the body hinges on the vehicle.  Note: the upper hinge pin is longer, which can be used to assist in guiding the door into place during installation.  Lower half-door hinge pins insert the upper and lower hinge pin screws into the body hinges.  Tighten the screws using a #T50 Torx", "the upper and lower hinge pin screws into the body hinges.  Tighten the screws using a #T50 Torx head driver to 3.8 ft\u00b7 lb / 5.2 N\u00b7m.  Caution: do not close the door before reattaching the door check to the body.  Damage may occur to the door check.  Do not overtighten Torx fasteners, damage to the vehicle\u2019s parts will occur.  Hinge pins can break if overtightened during door install (Max Torque: 6.0 ft\u00b7 lb/8.1 N\u00b7m).  Attach the cloth strap of the lower half-door to the metal hook just inside the vehicle.  Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap connect the wiring harness on the lower half-door to the connection just inside the vehicle.  Note: for front doors, make sure the wiring harness is closed completely.  Front door wiring harness 1 \u2014 open wiring harness 2 \u2014 closed wiring harness replace wiring access doors.  When the half-doors are shipped with the vehicle, the lower half-doors will have plugs in the post holes that must be removed prior to upper half-door installation.  To remove these", "in the post holes that must be removed prior to upper half-door installation.  To remove these plugs, proceed as follows: locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place tool into service hole of plug to remove using the tool, slowly pull upwards from the center of the plug to remove.  Making sure the window on the upper half-door is completely zipped closed, insert the upper half-door into the lower half-door by placing the posts into the post holes.  Lower the upper half-door into post holes push down firmly on the inside of the upper half-door until it is fully seated in the lower half.  Push Down To Fully Seat Upper Half-Door", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service", "is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors", "a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software,", "into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact", "you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by", "updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but", "engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.", "the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Opening The Hood Release both of the outside hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Note: Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.", "When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Note: depending on the vehicle\u2019s options, feature settings may vary.  To Activate Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.  WARNING: Leaving the Cruise Control system on when not in use is dangerous.  You could accidentally set the system or cause it to go faster than you want.  You could lose control and have an accident.  Always ensure the system is off when you are not using it.  STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery:", "we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan", "hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the", "image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check", "to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  Normal Starting Observe the instrument cluster lights when starting the engine.  Always apply the parking brake.", "Observe the instrument cluster lights when starting the engine.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  Note: a delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  Caution: if the water in fuel indicator light remains on, do not start the engine before you drain the water from the fuel filters to avoid engine damage.  The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Note: Normal starting of either a cold or a warm engine is", "turned off.  Release the parking brake.  Note: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades", "conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Stopping The Engine After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Note: Refer to the following chart for proper engine shutdown.  Note: Under certain conditions the Stop/Start system may be temporarily disabled and the engine fan will run after the engine is turned off to protect the engine.  These conditions are under high load and high temperature conditions.", "Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.", "in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If You Stall Or Begin To Lose Headway If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally", "REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of", "more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If the engine stalls or you lose", "the risk of a rollover, which may result in severe injury.  If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight", "it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.", "The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Retrieve funnel from under the right rear seat.  Fuel Funnel Location Refueling Funnel Remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting Funnel Ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from", "an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  The vehicle may be equipped with a refueling funnel.", "the clutch to overheat and cause a fire.  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  The engine may be switched off even if the warning light is on: repeated interruptions of the regeneration process could cause an early deterioration of engine oil.  For this reason it is always advisable to wait for the symbol to go off before turning off the engine, following the previously mentioned instructions.  Do not complete the DPF regeneration process when the vehicle is stopped.  See the following steps for refueling: Emergency Gas Can Refueling Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil", "periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note:", "reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow", "is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in", "warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.", "If Engine Fails To Start If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  WARNING: Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged", "engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly CAUTION: To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more", "the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  Engine is not started.  Some electrical devices are available (power windows, etc.  FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  Do Not Operate The Engine", "another brand of gasoline before considering service for the vehicle.  Do Not Operate The Engine With Failed Parts All engine failures give some warning before the parts fail.  Be on the alert for changes in performance, sounds, and visual evidence that the engine requires service.  Some important clues are: engine misfiring or vibrating severely sudden loss of power unusual engine noises fuel, oil or coolant leaks sudden change, outside the normal operating range, in the engine operating temperature excessive smoke oil pressure drop shifting fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the", "released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.", "To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries", "system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster", "in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The Autostop Mode, The Following Must Occur: Conditions That Will Cause The Engine To Start Automatically While In Autostop Mode: To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: Conditions that will cause the engine to start automatically while in STOP/START AUTOSTOP ACTIVE mode, the engine will start automatically when: This indicator light will illuminate when the Stop/Start function is in \u201cAutostop\u201d mode.  The Stop/Start feature is enabled after every normal engine start.  It will remain in", "mode.  The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  While in an Autostop, the Climate Control system may automatically adjust airflow to maintain cabin comfort.  Customer settings will be maintained upon return to an engine running condition.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This light alerts the driver that the vehicle is in the neutral mode", "If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The", "the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye", "Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction", "shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause", "when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the", "pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.", "of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist", "fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric topDo not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing", "use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your", "perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the", "and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use", "with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You", "Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Android Auto\u2122 allows you to access and stream your favorite music with apps like YouTube Music, iHeartRadio, and Spotify.  Using your smartphone\u2019s data plan, you can stream endless music on the road.  Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the", "a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  To use Android Auto\u2122 on your car display, you\u2019ll need an", "bar changes to the Android Auto\u2122 icon.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: The Android Auto\u2122 App displays", "your apps.  To use Android Auto\u2122, perform the following procedure: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a", "icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your", "data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you", "data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .", "4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front wheels.  The four-wheel drive system will be automatically engaged when the vehicle senses a loss of traction.  This range provides additional traction for varying road conditions.  2H Two-Wheel Drive High Range \u2014 This range is for normal street and highway driving on dry, hard surfaced roads.  4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front wheels.  The four-wheel drive system will be automatically engaged when the vehicle senses a loss of traction.  This range provides additional traction for varying road conditions.  4H Four-Wheel Drive High Range \u2014 This range maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction for loose, slippery road surfaces only.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together,", "the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L 4H The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.", "For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government", "ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction", "traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.  Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  Temperature Grades The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of", "grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.  Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.", "Cruise Control When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  The Cruise Control buttons are located on the right side of the steering wheel.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  Do not use in hilly terrain or with heavy loads.  When using the Cruise Control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.  Use Cruise Control in flat terrain and with", "disengage until you can get back to cruising speed.  Use Cruise Control in flat terrain and with light loads to maximize fuel efficiency.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise", "vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.", "Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information Placard", "tire size, and cold tire inflation pressures specified on the Tire And Loading Information Placard To determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on gawrs, vehicle loading, and trailer towing, see \"\u21e8vehicle loading\" .  Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading", "pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on GAWRs, vehicle loading, and trailer towing, see Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The", "driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.", "When using the AutoStick shift control, select the highest gear that allows for adequate performance and avoids frequent downshifts.  For example, choose \u201c5\u201d if the desired speed can be maintained.  Choose \u201c4\u201d or \u201c3\u201d if needed to maintain the desired speed.  To prevent excess heat generation, avoid continuous driving at high RPM.  Return to a higher gear or vehicle speed when grade and road conditions allow.  Pushing the set (+) , or set (-) button once will result in a 1 km/h speed adjustment.  Each subsequent tap of the button results in an adjustment of 1 km/h.  If the button is continually pushed, the set speed will continue to adjust in 10 km/h increments until the button is released, then the new set speed will be established.  Pushing the set (+) , or set (-) button once will result in a 1 km/h speed adjustment.  Each subsequent tap of the button results in an adjustment of 1 km/h.  If the button is continually pushed, the set speed will continue to adjust in 10 km/h increments until the button is", "continually pushed, the set speed will continue to adjust in 10 km/h increments until the button is released,The new set speed is reflected in the instrument cluster display.  To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster", "speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is", "ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speed", "To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  To remove the center head restraint, raise it as far as it can go.  Then, push the adjustment button and the release button at the base of each post while pulling the head restraint up.  A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  To raise the head restraint, pull upward on the head restraint.  To lower the head restraint,", "To raise the head restraint, pull upward on the head restraint.  To lower the head restraint, push the adjustment button located on the base of the head restraint, and push downward on the head restraint.  The release button does not need to be pushed to adjust the head restraint.  To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then, adjust it to the appropriate height using the adjustment button.  For information on child seat tether routing, see A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the", "occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  Do not drive the vehicle without the rear seat head restraints installed while passengers are occupying the rear seat.  In a collision, people riding in this area without the head restraints installed are more likely to be seriously injured or killed.  A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  Front Head Restraints To", "instructions prior to operating the vehicle or occupying a seat.  Front Head Restraints To raise the head restraint, pull upward on the head restraint.  To lower the head restraint, push the adjustment button located on the base of the head restraint, and push downward on the head restraint.  The release button does not need to be pushed to adjust the head restraint.  To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  WARNING: A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.", "ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  Note: Do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head.", "With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeHow long does it take to remotely start my vehicle?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will remote start your vehicle more quickly.  However its range is limited.  For example, when you are leaving the stadium after the game, you can use the Vehicle Branded App to remote start your vehicle and have the inside of", "the game, you can use the Vehicle Branded App to remote start your vehicle and have the inside of your vehicle comfortable by the time you get to it.  Will my vehicle be safe if I lose my wireless device?  People sometimes lose their wireless devices, which is why security measures have been engineered into the Vehicle Branded App.  Asking for your username, password and SiriusXM Guardian\u2122 Security PIN help to ensure that nobody can start your vehicle if they happen to find your device.  Can someone drive off with my vehicle using the App?  nob Driving your vehicle still requires the keys to be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the interior before you arrive.  Can I stop a vehicle that is being driven with the cancel Remote Vehicle Start command?  nob If the vehicle is in motion, the cancel Remote Vehicle Start button will not stop the vehicle.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work", "all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeThis remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  With Remote Start, the engine will only run for 15 minutes.", "Remote Start system.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, see These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.", "If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized", "In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d This warning light will turn on when there's a fault with the EPS system When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes", "and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  Push the SWAY BAR switch to disconnect or connect the sway bar.  The Sway Bar Indicator Light (located in the instrument cluster) will illuminate when the bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when activation conditions are not met.  The stabilizer/sway bar should remain in on-road mode during normal driving conditions.  The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.  If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response", "with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off CAUTION:", "are safe, pull over and let vehicle idle for a few moments until the light turns off CAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen", "out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with", "wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.", "for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Electric Power Steering (EPS) Fault Warning Light This warning light will turn on when there's a fault with the EPS system WARNING: Continued operation with reduced assist could pose a safety risk to yourself and others.  Service should be obtained as soon as possible.  If the \u201cPOWER STEERING HOT\u201d message and an", "Service should be obtained as soon as possible.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offIf the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  The heated steering wheel button is located on the center of", "is applying the brakes autonomously.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering", "and cause a fire.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  This warning light will turn on when there's a fault with the EPS system The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.", "The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  Upper Center None Time Current Econ Compass Range to Empty Trip A Distance Audio Average Econ Trip B Distance Outside Temp Menu Title Speedometer Adjustable Upper Anchorage If the compression is increased too much on the front upper corner of the rear doors, deformation of the seal will occur.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the", "Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the", "Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the", "or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "To enter the \u201cPartial Off\u201d mode, momentarily push the ESC OFF button and the ESC OFF Indicator Light will illuminate.  To turn the ESC on again, momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Automatic Headlight System will turn the headlights on or off according to ambient light levels.  To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation.  When the system is on, the headlight time delay feature is also on.  This means the headlights will stay on for up to 90 seconds (programmable through the uconnect settings \"\u21e8uconnect settings\" ) after you place the ignition into the off position.  To turn the automatic system off, move the", ") after you place the ignition into the off position.  To turn the automatic system off, move the headlight switch out of the AUTO position.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Reduce power to unnecessary loads if possible: Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets", "Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s exterior and interior lights.  When the \u201cDaytime Running Lights\u201d feature is selected, the daytime running lights can be turned on or off.  This feature is only allowed by law in the country of the vehicle purchase.  Depending on the vehicle\u2019s options, feature settings may vary.  Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your", "on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices", "use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  Interior Courtesy Lights When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn", "panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.", "Trac-Lok Rear Axle \u2014 If Equipped The Trac-Lok rear axle provides a constant driving force to both rear wheels and reduces wheel spin caused by the loss of traction at one driving wheel.  If traction differs between the two rear wheels, the differential automatically proportions the usable torque by providing more torque to the wheel that has traction.  Trac-Lok is especially helpful during slippery driving conditions.  With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction.  WARNING: On vehicles equipped with a limited-slip differential, never run the engine with one rear wheel off the ground.  The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of your vehicle.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum", "and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not", "same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to", "to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on", "road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road", "there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.", "4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together,", "the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any", "drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H", "rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.", "each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  2H (Two-Wheel Drive High Range) 4H (Four-Wheel Drive High Range) N (Neutral) 4L (Four-Wheel Drive Low Range) In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal", "4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L", "To Turn On The Engine Using The ENGINE START/STOP Button The transmission must be in PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage automatically after 10 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Stop the vehicle.  Shift the transmission into PARK, if possible.  If not, shift the transmission to NEUTRAL.  Push and hold the ENGINE START/STOP button until the engine turns off.  Wait approximately 30 seconds.  Restart the engine.  Shift into the desired gear range.  If the problem is no longer detected, the transmission will return to", "into the desired gear range.  If the problem is no longer detected, the transmission will return to normal operation.  To Turn On The Engine Using The ENGINE START/STOP Button  Normal Starting Observe the instrument cluster lights when starting the engine.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  Note: a delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  Caution: if the water in fuel indicator light remains on, do not start the engine before you drain the water from the fuel filters to avoid engine damage.  The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting,", "after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Note: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving", "weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Stopping The Engine After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Note: Refer to the following chart for proper engine shutdown.  Note: Under certain conditions the Stop/Start system may be temporarily disabled and the engine fan will run after the engine is turned off to protect the engine.  These conditions are under high load and high", "the engine is turned off to protect the engine.  These conditions are under high load and high temperature conditions.", "Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer", "15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.", "Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light", "can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.", "FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) NEUTRAL (N)  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear", "the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.", "Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant will return to the radiator from the coolant expansion bottle/recovery tank if so equipped.  The cap should be inspected and", "from the coolant expansion bottle/recovery tank if so equipped.  The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.  WARNING: Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  Potential signs of vehicle overheating: Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do", "scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.", "Key Left Vehicle Feature If a valid key fob is no longer detected inside the vehicle while the vehicle\u2019s ignition system is in the ON/RUN or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument cluster display along with an interior chime.  An exterior audible and visual alert will also be activated to warn the driver.  The vehicle\u2019s horn will rapidly chirp three times along with a single flash of the vehicle\u2019s exterior lights.  Note: The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Key Left Vehicle Feature If a valid key fob is no longer detected inside the vehicle while the vehicle\u2019s ignition system is in the ON/RUN or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument", "or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument cluster display along with an interior chime.  An exterior audible and visual alert will also be activated to warn the driver.  The vehicle\u2019s horn will rapidly chirp three times along with a single flash of the vehicle\u2019s exterior lights.  Note: The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Off Road+ Indicator Light \u2014 If Equipped This indicator light will illuminate when Off Road+ has been activated.  Sway Bar Indicator Light \u2014 If Equipped This indicator light will illuminate when the front sway bar is disconnected.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and", "which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic", "subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .", "Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d", "and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.", "of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear", "Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as", "bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and", "up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up", "the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear", "can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.", "START The engine will start.  Note: In case the ignition switch does not change with the push of the START/STOP ignition button, the key fob may have a low or depleted battery.  In this situation, a backup method can be used to operate the ignition switch.  Put the nose side of the key fob (side with the mechanical flip key) against the START/STOP ignition button and push to operate the ignition switch.  CAUTION: Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.  WARNING: When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.", "is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the Keyless Enter \u2018n Go\u2122 Ignition in the ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat buildup may cause serious injury or death.  CAUTION: An unlocked vehicle is an invitation for thieves.  Always remove key fob from the vehicle and lock all doors when leaving the vehicle unattended.  Note: When opening the driver's door with the ignition in the ON/RUN (engine not running) position, a chime will sound to remind you to place the ignition in the OFF position.  In addition to the chime, the message will display \u201cIgnition Or Accessory On\u201d in the cluster.  Key Left Vehicle Feature If a", "the message will display \u201cIgnition Or Accessory On\u201d in the cluster.  Key Left Vehicle Feature If a valid key fob is no longer detected inside the vehicle while the vehicle\u2019s ignition system is in the ON/RUN or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument cluster display along with an interior chime.  An exterior audible and visual alert will also be activated to warn the driver.  The vehicle\u2019s horn will rapidly chirp three times along with a single flash of the vehicle\u2019s exterior lights.  Note: The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or", "Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do", "in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "Crossing Logs To cross a log, approach it at a slight angle (approximately 10 to 15 degrees).  This allows one front tire to be on top of the log while the other just starts to climb the log.  While climbing the log, modulate your brake and accelerator to avoid spinning the log out from under your tires.  Then ease the vehicle off the log using your brakes.  CAUTION: Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high-centered.  Before You Cross Any Type Of Water As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and", "can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Crossing A Ravine, Gully, Ditch, Washout Or Rut When crossing a ravine, gully, ditch, washout or a large rut, the angled approach is the key to maintaining your vehicle's mobility.  Approach these obstacles at a 45-degree angle and let each tire go through the obstacle independently.  You need to use caution when crossing large obstacles with steep sides.  Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover.  If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires.  Use the removed dirt to fill the rut ahead of the turnout you just created.  You should now be able to drive out", "dirt to fill the rut ahead of the turnout you just created.  You should now be able to drive out following the trench you just created at a 45-degree angle.  WARNING: There is an increased risk of rollover when crossing an obstacle, at any angle, with steep sides.", "Non-Locking Storage Wall The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  There is also an option to remove the wall by removing the four bolts that connect the storage wall to the floor.  Non-Locking Storage Wall The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  There is also an option to remove the wall by removing the four bolts that connect the storage wall to the floor.  Rear Wall Storage Bin To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  Note: The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  The Locking Storage Bin has two keyed locks on the front of", "to limit access to items behind seat.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.", "If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for serviceIn unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature", "whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the", "procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an", "reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns", "will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a", "clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service,", "overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is", "Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  If the vehicle is overheating, it will need to be serviced by an authorized dealer.", "EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to", "but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than", "was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.", "and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start", "10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M", "during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident,", "compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's", "illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "To enter the \u201cPartial Off\u201d mode, momentarily push the ESC OFF button and the ESC OFF Indicator Light will illuminate.  To turn the ESC on again, momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Automatic Headlight System will turn the headlights on or off according to ambient light levels.  To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation.  When the system is on, the headlight time delay feature is also on.  This means the headlights will stay on for up to 90 seconds (programmable through the uconnect settings \"\u21e8uconnect settings\" ) after you place the ignition into the off position.  To turn the automatic system off, move the", ") after you place the ignition into the off position.  To turn the automatic system off, move the headlight switch out of the AUTO position.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Reduce power to unnecessary loads if possible: Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets", "Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s exterior and interior lights.  When the \u201cDaytime Running Lights\u201d feature is selected, the daytime running lights can be turned on or off.  This feature is only allowed by law in the country of the vehicle purchase.  Depending on the vehicle\u2019s options, feature settings may vary.  Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your", "on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices", "use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn", "panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  Interior Courtesy Lights When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time", "the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.", "Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate", "provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.", "on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.", "Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be", "Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire dealer or original", "those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result", "what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw", "accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  Tires Examine tires for excessive tread wear and uneven wear patterns.  Check for stones, nails, glass, or other objects lodged in the tread or sidewall.  Inspect the tread for cuts and cracks.  Inspect sidewalls for cuts, cracks, and bulges.  Check the lug nut/bolt torque for tightness.  Check the tires (including spare) for proper cold", "Check the lug nut/bolt torque for tightness.  Check the tires (including spare) for proper cold inflation pressure.", "To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security", "Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped)Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the", "armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open", "arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second", "action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.", "When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is", "the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an", "brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the", "the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  If the headlights or parking lights are left on after the ignition is placed in the OFF position, the vehicle will chime when the driver\u2019s door is opened.  Vehicle parking brake is applied Stability event occurs Gear selector is moved out of DRIVE Engine overspeed occurs Clutch pedal is pressed (manual transmission only) Vehicle is operating at a low RPM (manual transmission only) Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five", "brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  release the parking brake  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System", "system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If", "monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake", "it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.", "Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  The rearview mirror can be adjusted up, down, left, and right.  The mirror", "for on-road use.  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  Manual Mirror Adjustment If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the", "reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Ignoring the Rearview Mirror light could mean you will not have SOS Call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  When cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray", "cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on the mirror.", "Off-Road Driving Tips  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled", "you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface", "should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?", "Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or", "with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of", "and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match", "Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl", "or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.", "Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect", "against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.", "vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code", "leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants", "are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the", "the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric topDo not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Place the vehicle in a warm", "installation can cause water to leak into the vehicle's interior.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  From the Sunrider\u00ae Position, remove straps if previously secured.  Step One Failure to follow the next steps could result in damage to the soft top or vehicle.  Using the side link, lift and push the soft top toward the front of the vehicle, manually guiding the top into the closed position.  Step Two Step Two From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Step Three Pull the handle back upward while squeezing the hook, locking the latch into place.  Step Four It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water", "it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information Placard To determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on gawrs, vehicle loading, and trailer towing, see \"\u21e8vehicle loading\" .  Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not", "on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on GAWRs, vehicle loading, and trailer towing, see Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed", "axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  All cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb", "transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  (1) Locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.\u201d on your vehicle's placard.", "Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose", "the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.", "and power steering, and fill as needed.  Check function of all interior and exterior lights.  PARKING BRAKE Before exiting the vehicle, make sure that the parking brake is fully applied.  Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or FIRST gear.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to", "selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  WARNING: Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  CAUTION: If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  You or others could be injured", "Have the brake system serviced by an authorized dealer immediately.  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied.  The parking brake should always be applied when the driver is not in the vehicle, especially on an incline.  Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle,", "parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the", "in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.", "For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government", "ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction", "traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.  DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces", "stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.", "The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  Drivetrain Menu 2WD/4WD Drivetrain  Drivetrain The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  The following information is displayed: steering angle in degrees status of transfer case status of front axles \u2014 if equipped status of the rear axles \u2014 if equipped.  Drivetrain The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  The following information is displayed: steering angle in degrees status of transfer case status of front axles \u2014 if equipped status of the rear axles \u2014 if equipped drivetrain front wheel angle: displays the graphical and numerical value of calculated average front wheel angle from the steering wheel orientation.  Transfer Case Lock Status: displays \u201cLock\u201d graphic only during 4WD High, 4WD Auto, or 4WD Low status.  Axle Lock And Sway Bar Status (if equipped): displays front and rear or rear only axle locker graphic, and sway bar connection graphic with", "displays front and rear or rear only axle locker graphic, and sway bar connection graphic with text message (connected or disconnected).", "The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  Power Window Switches Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel", "10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.  Feature description controls \u2014 if equipped press the controls button to access vehicle-specific features like heated seats and steering wheel.  Apps press the apps button to access a list of the available mobile apps.  Climate press the climate button to enter climate mode and access the climate control functions.  Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF.  Climate Control OFF Button Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  Recirculation Button Push the Recirculation button on the faceplate to change the system between recirculation mode and outside air mode.  The Recirculation indicator and the A/C indicator (if equipped) illuminate when the", "air mode.  The Recirculation indicator and the A/C indicator (if equipped) illuminate when the Recirculation button is pressed.  Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.  Recirculation can be used in all modes except for Defrost.  Recirculation may be unavailable if conditions exist that could create fogging on the inside of the windshield.  The A/C can be deselected manually without disturbing the mode control selection.  Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur.  Extended use of this mode is not recommended.  On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode to improve window clearing operation.  Recirculation is disabled automatically if this mode is selected.  Attempting to use Recirculation while in this mode causes the LED on the control button to blink and then turn off.  Recirculation Button Press and release this button on the", "button to blink and then turn off.  Recirculation Button Press and release this button on the touchscreen, or push the button on the faceplate to change the system between recirculation mode and outside air mode.  The Recirculation indicator and the A/C indicator illuminate when the Recirculation button is pressed.  Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.  Recirculation can be used in all modes Recirculation may be unavailable (button on the touchscreen grayed out) if conditions exist that could create fogging on the inside of the windshield.  The A/C can be deselected manually without disturbing the mode control selection.  Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur.  Extended use of this mode is not recommended.  Recirculation mode may automatically adjust to optimize customer experience for warming, cooling, dehumidification, etc.  POWER WINDOWS \u2014 IF EQUIPPED The power windows", "for warming, cooling, dehumidification, etc.  POWER WINDOWS \u2014 IF EQUIPPED The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The top left switch controls the left front window and the top right switch controls the right front window.  The bottom left switch controls the left rear window and the bottom right switch controls the right rear window.  WARNING: Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  Note: The power window switches will remain active for up to 10 minutes after the", "injury or death.  Note: The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Preparations For Jacking Park on a firm, level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking", "operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  With extended use the Hazard Warning Flashers may wear down your battery.  The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue", "When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Hazard Warning Flashers Button The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  This is an emergency", "the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.  turn on the Hazard Warning Flashers.  Apply the parking brake firmly and shift an automatic transmission in PARK; a manual transmission to REVERSE.  Block the wheel diagonally opposite the wheel to be raised.  Never start or run the engine with the vehicle on a jack.  Do not let anyone sit in the vehicle when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.  Only use the jack in the positions indicated and for lifting this vehicle during a tire change.  If working on or near a roadway, be extremely careful of", "this vehicle during a tire change.  If working on or near a roadway, be extremely careful of motor traffic.  To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  Yellow indicator lights 4wd indicator light \"\u21e84wd indicator light \u2014 if equipped\" 4wd low indicator light \"\u21e84wd low indicator light \u2014 if equipped\" 4wd part time indicator light \"\u21e84wd part time indicator light \u2014 if equipped\" axle locker fault indicator light \"\u21e8axle locker fault indicator light \u2014 if equipped\" rear axle lock indicator light \"\u21e8rear axle lock indicator light \u2014 if equipped\" front and rear axle lock indicator light \"\u21e8front and rear axle lock indicator light \u2014 if equipped\" forward collision warning off indicator light \"\u21e8forward collision warning off indicator light \u2014 if equipped\" neutral indicator light \"\u21e8neutral indicator light \u2014 if equipped\" sway bar indicator light \"\u21e8sway", "neutral indicator light \"\u21e8neutral indicator light \u2014 if equipped\" sway bar indicator light \"\u21e8sway bar indicator light \u2014 if equipped\" off road+ indicator light \"\u21e8off road+ indicator light \u2014 if equipped\" cargo light on indicator light \"\u21e8cargo light on indicator light\" wait to start indicator light \"\u21e8wait to start indicator light \u2014 if equipped\" low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \"\u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped\" water in fuel indicator light \"\u21e8water in fuel indicator light \u2014 if equipped\" selec speed control (ssc) indicator light \u2014 if equipped this light will turn on when selec speed control is activated.  Selec Speed Control is available in 4WD Low ONLY.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear", "forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  Yellow indicator lights 4wd indicator light  \u21e84wd indicator light \u2014 if equipped  4wd low indicator light  \u21e84wd low indicator light \u2014 if equipped  4wd part time indicator light  \u21e84wd part time indicator light \u2014 if equipped  axle locker fault indicator light  \u21e8axle locker fault indicator light \u2014 if equipped  rear axle lock indicator light  \u21e8rear axle lock indicator light \u2014 if equipped  front and rear axle lock indicator light  \u21e8front and rear axle lock indicator light \u2014 if equipped  forward collision warning off indicator light", "and rear axle lock indicator light \u2014 if equipped  forward collision warning off indicator light  \u21e8forward collision warning off indicator light \u2014 if equipped  neutral indicator light  \u21e8neutral indicator light \u2014 if equipped  sway bar indicator light  \u21e8sway bar indicator light \u2014 if equipped  off road+ indicator light  \u21e8off road+ indicator light \u2014 if equipped  cargo light on indicator light  \u21e8cargo light on indicator light  wait to start indicator light  \u21e8wait to start indicator light \u2014 if equipped  low diesel exhaust emissions additive adblue\u00ae (urea) indicator light  \u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped  water in fuel indicator light  \u21e8water in fuel indicator light \u2014 if equipped  green indicator lights 4wd auto indicator light  \u21e84wd auto indicator light \u2014 if equipped  front fog indicator light  \u21e8front fog indicator light \u2014 if equipped  parking/headlights on indicator light  \u21e8parking/headlights on indicator light  stop/start active indicator light  \u21e8stop/start", "light  \u21e8parking/headlights on indicator light  stop/start active indicator light  \u21e8stop/start active indicator light \u2014 if equipped  turn signal indicator lights  \u21e8turn signal indicator lights  rear seat belt fastened indicator light.", "Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death", "be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated", "de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Your vehicle may be equipped with a secondary battery used to power the", "to provide starting.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps", "or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.", "Remote Start Windshield Wiper De-Icer Activation \u2014 If Equipped When Remote Start is active and the outside ambient temperature is less than 33\u00b0F (0.6\u00b0C), the Windshield Wiper De-Icer will activate.  Exiting Remote Start will resume previous operation.  If the Windshield Wiper De-Icer was active, the Windshield Wiper De-Icer timer and operation will continue.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.", "could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  Remote Start Front Defrost Activation \u2014 If Equipped When Remote Start is active, and the outside ambient temperature is 40\u00b0F (4.5\u00b0C) or below, the system will automatically activate front defrost for 15 minutes or less.  The time is dependent on the ambient temperature.  Once the timer expires, the system will automatically adjust the settings", "the ambient temperature.  Once the timer expires, the system will automatically adjust the settings depending on ambient conditions.  See \u201cRemote Start Comfort Systems \u2014 If Equipped\u201d in the next section for detailed operation.", "Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel", "only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damageIf climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway", "Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good", "using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  CAUTION: If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage Diesel Fuel Specifications This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine", "tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump", "at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).", "Rolling Code Devices To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Note: The \u201cLEARN\u201d or \u201cTRAIN\u201d button is not the button you normally use to operate the device.  To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Before programming a device to one of your HomeLink\u00ae buttons,", "may vary slightly by manufacturer.  Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  You have 30 seconds in which to initiate rolling code final step 2, after completing rolling code final step 1.  Identifying Whether You Have A Rolling Code Or Non-Rolling Code Device Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.", "Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch", "use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or", "A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious", "is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Maps Push and hold the VR button on the steering wheel until the beep or tap the Microphone icon to ask Apple\u00ae Siri to take you to a desired destination by voice.  You can also touch the Navigation icon in Apple CarPlay\u00ae to access Apple\u00ae Maps.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.", "Apple CarPlay\u00ae Voice Command Apple CarPlay\u00ae allows you to use your voice to interact with Siri through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your iPhone\u00ae and a number of its apps onto your Uconnect touchscreen.  Connect your iPhone\u00ae 5 or higher to one of the media USB ports, using the factory-provided Lightning cable, and press the new Apple CarPlay\u00ae icon that replaces your Phone icon on the main menu bar to begin Apple CarPlay\u00ae.  Push and hold the vr button on the steering wheel, or press and hold the home button within apple carplay\u00ae, to activate siri, which recognizes natural voice commands to use a list of your iphone\u00ae features: phone music messages maps \u2014 if equipped additional apps \u2014 if equipped note: feature availability depends on your carrier and mobile phone maker.  Some Apple CarPlay\u00ae features may not be available in every region and/or language.  Note: Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered", "Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered in the US and other countries.  Apple\u00ae terms of use and privacy statements apply.  Apple carplay\u00ae apple carplay\u00ae \u00b9 use this qr code to access your digital experience.  Uconnect works seamlessly with Apple CarPlay\u00ae, the smarter, more secure way to use your iPhone\u00ae in the car, and stay focused on the road.  Use your Uconnect Touchscreen display, the vehicle's knobs and controls, and your voice with Siri to get access to Apple Music\u00ae, Maps, Messages, and more.  To use Apple CarPlay\u00ae, make sure you are using iPhone\u00ae 5 or later, have Siri enabled in Settings, ensure your iPhone\u00ae is unlocked for the very first connection only, and then use the following procedure: Connect your iPhone\u00ae to one of the media USB ports in your vehicle.  Note: be sure to use the factory-provided lightning cable that came with your phone, as aftermarket cables may not work.  Once the device is connected and recognized, the Phone icon on the", "cables may not work.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Apple CarPlay\u00ae Icon.  Note: apple carplay\u00ae is set to launch immediately.  You can also launch it by pressing the Apple CarPlay\u00ae icon on the touchscreen.  Apple carplay\u00ae and lte data coverage 1 \u2014 lte data coverage 2 \u2014 apple carplay\u00ae icon once apple carplay\u00ae is up and running on your uconnect system, the following features can be utilized using your iphone\u00ae data plan: phone music messages maps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Apple CarPlay\u00ae features may or may not be available in every region and/or language.  Note: To use Apple CarPlay\u00ae, make sure that cellular data is turned on, and that you are in an area with cellular coverage.  Your data and cellular coverage is shown on the left side of the radio screen.  Data plan rates apply.  Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Apple CarPlay\u00ae.  Anywhere using your mobile device and Vehicle Branded App From your computer on the Owner\u2019s Site (not available on all functions) Contacting SiriusXM Guardian\u2122 Customer Care (not available on all functions) Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.", "function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Closing The Hood To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.", "rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  WARNING: Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.", "Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on GAWRs, vehicle loading, and trailer towing, see Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.", "capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.", "GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  For further information on GAWRs, vehicle loading, and trailer towing, see  Gross Axle Weight Rating (GAWR)", "information on GAWRs, vehicle loading, and trailer towing, see  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to", "this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation.  The entire vehicle should first be weighed on a commercial scale to ensure that the GVWR has not been exceeded.  The weight on the front and rear of the vehicle should then be", "the GVWR has not been exceeded.  The weight on the front and rear of the vehicle should then be determined separately to be sure that the load is properly distributed over the front and rear axle.  Weighing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.  If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met.  Store the heavier items down low and be sure that the weight is distributed equally.  Stow all loose items securely before driving.  Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate.  WARNING: Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR.  If you do, parts on your vehicle can break, or it can change the way your vehicle handles.  This could cause you to lose control.  Overloading can shorten the life of your vehicle.", "Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.  Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d The buttons on the right side of the steering wheel operate the ACC system.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged ACC Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following appears in the instrument cluster display:  Driver Assist \u2014 If Equipped The Driver Assist menu displays the status of the ACC system.  Push and release the up or down arrow button", "Assist menu displays the status of the ACC system.  Push and release the up or down arrow button until the driver assist menu is displayed in the instrument cluster display.", "The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Locking Storage Bin (Closed View) Locking Storage Bin  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be", "bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  Locking Storage Bin  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.", "vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.", "To use the mid position, open the tailgate and lower it to near mid position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  Tailgate In Mid Position  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014", "the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located", "provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.", "DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If", "must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne", "corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.", "lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following", "display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122", "auto\u2122.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the", "first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your", "your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android", "factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is", "and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apps The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be", "and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the", "Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Description SmartWatch Integration puts the Vehicle Branded App right on your Apple\u00ae Watch or Android\u2122 Wear.  To get started,", "puts the Vehicle Branded App right on your Apple\u00ae Watch or Android\u2122 Wear.  To get started, follow these steps: Download the Vehicle Branded App from the App Store\u00ae or Google Play.  Log onto the app from your smartphone using the username and password you created when you first set up your account.  Make sure your watch and smartphone are connected through Bluetooth\u00ae.  The Vehicle Branded App should appear on your SmartWatch.  Once the app is downloaded on your SmartWatch, you can enjoy these features: Lock or unlock your vehicle by tapping the remote lock button in the app and entering your security PIN.  Remote start or stop your vehicle.  View important vehicle stats, such as fuel level, vehicle location, tire pressure warning, and more.", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and", "seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information:", "canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html frequently asked questions about installing child restraints with seat belts what is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward-facing child restraint, up to the recommended weight limit of the child restraint.  Can the rear-facing child restraint touch the back of the front passenger seat?  Yes contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.  Can the rear head restraints be removed?  Yes the center head restraint can be removed if it interferes with the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt", "the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint?  No do not twist the buckle stalk in a seating position with an alr retractor.  Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.  Use this simple 5-step test to decide whether the child can use the vehicle\u2019s seat belt alone: Can the child sit all the way back against the back of the vehicle seat?  Do the child\u2019s knees bend comfortably over the front of the vehicle seat while the child is still sitting all the way back?  Does the shoulder belt cross the child\u2019s shoulder between the neck and arm?  Is the lap part of the belt as low as possible, touching the child\u2019s thighs and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to", "and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to any of these questions was \u201cno,\u201d then the child still needs to use a booster seat in this vehicle.  If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s squirming or slouching can move the belt out of position.  If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.  WARNING: Never allow a child to put the shoulder belt under an arm or behind their back.  In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.  A child must always wear both the lap and shoulder portions of the seat belt correctly.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with", "systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.", "If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning", "you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder", "parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  Brake System Warning Light The red Brake System Warning Light will turn on when the", "immediately.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction", "mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force", "equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake", "checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to", "Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera", "Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable", "into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on", "The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable", "into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen", "\u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while", "in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Guide the top of the quarter panel cover assembly up into the retainer.  Step One Failure to follow", "Guide the top of the quarter panel cover assembly up into the retainer.  Step One Failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the Soft Top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step Two It is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step Three From either side, guide the rear window into the retainer while keeping the window level.  Step Four Engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step Five Engage the vertical retainers up the right and", "window is secured in the lower retainer.  Step Five Engage the vertical retainers up the right and left side of the rear window.  Step Six Tuck the rear window under the soft top fabric and press firmly.  Step Seven Engage the rear window retainers in the lower right and left corners.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step Two 1 \u2014 Outside Panel Lock 2 \u2014 Rear Panel Lock 3 \u2014 Front Panel Lock Unlatch the left side header panel latch located at the top of the windshield.  Step Three Remove the left side panel.  Repeat the preceding steps to remove the right side panel.  Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while", "retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage", "the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.", "Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Natural Speech Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Natural speech allows the user to speak commands in phrases or complete sentences.  The system filters out certain non-word utterances and sounds such as \u201cah\u201d and \u201ceh.\u201d The system handles fill-in words such as \u201cI would like to\u201d.  The system handles multiple inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you", "identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you want to call?\u201d in the case where a phone call was requested but the specific name was not recognized.  The system utilizes continuous dialog.  When the system requires more information from the user, it will ask a question to which the user can respond without pushing the Voice Command button on the steering wheel.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear", "the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of", "of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature", "Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.", "Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.  Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d The buttons on the right side of the steering wheel operate the ACC system.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged ACC Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following appears in the instrument cluster display:  Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d", "Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d The buttons on the right side of the steering wheel operate the ACC system.  When the SET (+) or the SET (-) button (located on the steering wheel) is pushed, the display will read \u201cACC SET.\u201d Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following appears in the instrument cluster display: Push the ACC ON/OFF button (located on the steering wheel) until one of the following displays in the instrument cluster display: The Driver Assist menu displays the status of the ACC system.  When driving with ACC engaged and following a vehicle, the system will provide an additional acceleration up to the ACC set speed to assist in passing the vehicle.  This additional acceleration is triggered when the driver utilizes the left turn signal and will only be active when passing on the left hand side.  To turn the system off, push and release the Adaptive Cruise Control", "on the left hand side.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d While ACC with Stop is holding your vehicle at a standstill, if the driver seat belt is unbuckled or the driver door is opened, the ACC with Stop system will cancel and the brakes will release.  A cancel message will display on the instrument cluster display and produce a warning chime.  Driver intervention will be required at this moment.  The specified following distance for ACC can be set by varying the distance setting between four bars (longest), three bars (long), two bars (medium) and one bar (short).  Using this distance setting and the vehicle speed, ACC calculates and sets the distance to the vehicle ahead.  This distance setting displays in the instrument cluster display.", "If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you", "prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides", "a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is", "may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  FOLDING WINDSHIELD The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element provides.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving", "the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  WARNING: Carefully follow these warnings to help protect against personal injury: Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these", "fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "The ACC screen may display once again if any ACC activity occurs, which may include any of the following: This feature will only activate when the following conditions are met: The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: Once SSC is enabled it will activate automatically once the following conditions are met: The following conditions must be met in order for HSA to activate:  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: If the ABS Warning", "also may experience the following normal characteristics when the ABS activates: If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN", "If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To", "by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply", "most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the", "portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.", "Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  The ABS is designed to function with the Original Equipment Manufacturer (OEM) tires.  Modification may result in degraded ABS performance.  Your vehicle is equipped with an advanced Electronic Brake Control (EBC) system.  This system includes Anti-Lock Brake", "with an advanced Electronic Brake Control (EBC) system.  This system includes Anti-Lock Brake System (ABS), Brake Assist System (BAS), Electronic Brake Force Distribution (EBD), Electronic Roll Mitigation (ERM), Electronic Stability Control (ESC), Hill Start Assist (HSA), and Traction Control System (TCS).  These systems work together to enhance both vehicle stability and control in various driving conditions.", "REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engineThis allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from", "monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an", "cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a", "between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The Autostop Mode, The Following Must Occur: Conditions That Will Cause The Engine To Start Automatically While In Autostop Mode: To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: Conditions that will cause the engine to start automatically while in STOP/START AUTOSTOP ACTIVE mode, the engine will start automatically when: This indicator light will illuminate when the Stop/Start function is in \u201cAutostop\u201d mode.  The", "when: This indicator light will illuminate when the Stop/Start function is in \u201cAutostop\u201d mode.  The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  While in an Autostop, the Climate Control system may automatically adjust airflow to maintain cabin comfort.  Customer settings will be maintained upon return to an engine running condition.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow", "the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This light alerts the driver that the vehicle is in the neutral mode  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message", "The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an", "illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.  SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of", "on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is", "the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke", "and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s", "equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.", "2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.", "Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam", "the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.  Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Automatic Dimming Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  This mirror automatically adjusts for", "be adjusted to center on the view through the rear window.  This mirror automatically adjusts for headlight glare from vehicles behind you.  The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Note: The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  Automatic High Beam Headlamp Control \u2014 If Equipped The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automatically controlling the high beams through the use of a camera mounted on the vehicle\u2019s header.  This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.  Note: the automatic high beam headlamp control can be turned on or", "vehicle is out of view.  Note: the automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.", "Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial", "tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Wheel And Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels", "mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Your wheels are susceptible to deterioration caused by salt, sodium chloride, magnesium chloride, calcium chloride, etc., and other road chemicals used to melt ice or control dust on dirt roads.  Use a soft cloth or sponge and mild soap to wipe away promptly.  Do not use harsh chemicals or a stiff brush.  They can damage the wheel\u2019s protective coating that helps keep them from corroding and tarnishing.  When cleaning extremely dirty wheels, including excessive brake dust, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels.  Mopar\u00ae Wheel Treatment or Mopar\u00ae Chrome Cleaner, or their equivalent, is recommended or select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels.  CAUTION: Avoid products", "select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels.  CAUTION: Avoid products or automatic car washes that use acidic solutions or strong alkaline additives or harsh brushes.  Many aftermarket wheel cleaners and automatic car washes may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  CAUTION: Do not use scouring pads, steel wool, a bristle brush, metal polishes, or oven cleaner.  These products may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  Note: If you intend parking or storing your vehicle for an extended period after cleaning the wheels with wheel cleaner, drive your vehicle and apply the brakes to remove the water droplets from the brake components.  This activity will remove the red rust on the brake rotors and prevent vehicle", "brake components.  This activity will remove the red rust on the brake rotors and prevent vehicle vibration when braking.  ENGINE FLUIDS AND LUBRICANTS CAUTION: Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant", "inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Note: If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.", "WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been", "the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it", "tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.", "To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument", "Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions", "must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote", "have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).", "the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset", "engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic", "before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote", "the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  To Accelerate For Passing While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is", "the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  Do not use in hilly terrain or with heavy loads.  When using the Cruise Control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.  Use Cruise Control in flat terrain and with light loads to maximize fuel efficiency.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d", "Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Recommended Distribution Hitch Adjustment An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  Outside Air Intake Make sure the air intake, located directly in front of the windshield, is free of", "Air Intake Make sure the air intake, located directly in front of the windshield, is free of obstructions, such as leaves.  Leaves collected in the air intake may reduce airflow, and if they enter the air distribution box, they could plug the water drains.  In Winter months, make sure the air intake is clear of ice, slush, and snow.", "Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines", "of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification", "call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L", "meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round", "fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  Open the fuel filler door.  Fuel Filler Door Remove the diesel fuel filler cap by rotating it counterclockwise.  Fuel and Diesel Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the vehicle with fuel.  When the nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel", "excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel filler door.  FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is", "provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  Caution: if the water in fuel indicator light remains on, do not start engine before you drain the water from the fuel filter(s) to avoid engine damage \"\u21e8draining fuel/water separator filter \u2014 diesel engine\" .  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most", "diesel engine\" .  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of", "or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using", "to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API", "3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).", "Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Uconnect 4C/4C NAV with 8.4-inch Display Uconnect 4C/4C NAV With 8.4-inch Display Automatic Climate Controls Uconnect 4C/4C NAV With 8.4-inch Display Touchscreen And Faceplate Buttons  Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  UCONNECT", "the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  UCONNECT VOICE RECOGNITION Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.", "Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To", "the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: for the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  The engine is allowed to crank as long as 25 seconds.  If the engine fails to start during this period, please wait at", "to crank as long as 25 seconds.  If the engine fails to start during this period, please wait at least two minutes for the starter to cool before repeating start procedure.  If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filters to avoid engine damage", "Fastener Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  To remove the Fastener Bin: Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Note: The soft top fasteners do not go in the Fastener Bin.  Rear Wall Storage Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  Fastener Bin Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Installing The Soft Top Install the belt rail on the rear of", "from the bottom of the Fastener Bin.  Installing The Soft Top Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque specification for torx fastener maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  Damage to the retainers will occur.  Step one 1 \u2014 corner fasteners 2 \u2014 rear fasteners install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Caution: failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the", "the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step four using the provided #t50 torx head driver and ratchet, install and tighten the torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step five torque specification for torx fasteners maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Step five before driving the vehicle with the top in the sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners.  Step Six Note:", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Closing The Hood To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.", "rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  WARNING: Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.", "What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to", "are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Wheel And Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Your wheels are susceptible to deterioration caused by salt, sodium chloride, magnesium chloride, calcium chloride, etc., and other road chemicals used to melt ice or control dust on dirt roads.  Use a soft", "etc., and other road chemicals used to melt ice or control dust on dirt roads.  Use a soft cloth or sponge and mild soap to wipe away promptly.  Do not use harsh chemicals or a stiff brush.  They can damage the wheel\u2019s protective coating that helps keep them from corroding and tarnishing.  When cleaning extremely dirty wheels, including excessive brake dust, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels.  Mopar\u00ae Wheel Treatment or Mopar\u00ae Chrome Cleaner, or their equivalent, is recommended or select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels.  CAUTION: Avoid products or automatic car washes that use acidic solutions or strong alkaline additives or harsh brushes.  Many aftermarket wheel cleaners and automatic car washes may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  CAUTION: Do not use", "Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  CAUTION: Do not use scouring pads, steel wool, a bristle brush, metal polishes, or oven cleaner.  These products may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  Note: If you intend parking or storing your vehicle for an extended period after cleaning the wheels with wheel cleaner, drive your vehicle and apply the brakes to remove the water droplets from the brake components.  This activity will remove the red rust on the brake rotors and prevent vehicle vibration when braking.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial", "tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such", "coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.", "Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the", "before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper", "and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait", "the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.", "Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat buildup may cause serious injury or death.  It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.  In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.  Be sure everyone in your vehicle is in a seat and using a seat belt properly.  60/40 Split Folding Rear Seat The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped)WARNING: The seatback is not intended to be used for storing cargo when folded flat, and only folds to allow access to the cargo area behind the", "for storing cargo when folded flat, and only folds to allow access to the cargo area behind the seat.  Do not operate the vehicle with unsecured cargo on the second row folded seatback.  Note: Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.  In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.  Be sure everyone in your vehicle is in a seat and using a seat belt properly.  The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to", "lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  This vehicle has front air bags and lap/shoulder belts for both the driver and front passenger.  The front air bags are a supplement to the seat belt restraint systems.  The driver front air bag is mounted in the center of the steering wheel.  The passenger front air bag is mounted in the instrument panel, above the glove compartment.  The words \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d are embossed on the air bag covers.  This vehicle has an Occupant Classification System (\u201cOCS\u201d) in the front passenger seat.  The OCS is designed to activate or deactivate the Passenger Advanced Front Air Bag depending on the occupant\u2019s seated weight.  It is designed to deactivate the Passenger Advanced Front Air Bag for an unoccupied seat and for occupants whose seated weight classifies them in a category other than a properly seated adult.  This could be a child, teenager, or even an adult.  Cargo must be", "than a properly seated adult.  This could be a child, teenager, or even an adult.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.", "Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To", "location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut", "To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.", "The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.", "160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to", "(with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Turn off the Fuel Filter Heater, Turn off the HVAC Blower Motor, Close the HVAC Circulation Door Cut off battery power to the: Engine Electric Motor (if equipped) Electric power steering Brake booster Electric park brake Automatic transmission gear selector Horn Front wiper  Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in", "be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or", "is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life", "plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Extreme Cold Weather The cartridge block heater clips into the", "authorized dealer) is recommended.  Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.", "SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey", "through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS", "in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s", "into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call,", "You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.  Sos call system limitations vehicles sold in mexico do not have sos call system capabilities.  SOS or other emergency line operators in Mexico may not answer or respond to SOS system calls.  If the SOS Call system detects a malfunction, any of the following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message", "buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d an in-vehicle audio message will state \u201cvehicle device requires service.  Please contact an authorized dealer.\u201d even if the sos call system is fully functional, factors beyond fca us llc\u2019s control may prevent or stop the sos call system operation.  These include, but are not limited to, the following factors: the ignition is in the off position the vehicle\u2019s electrical systems are not intact the sos call system software and/or hardware are damaged during a crash the vehicle battery loses power or becomes disconnected during a vehicle crash lte (voice/data) or 4g (data) network and/or global positioning satellite signals are unavailable or obstructed equipment malfunction at the sos operator facility operator error by the sos operator lte (voice/data) or 4g (data) network congestion weather buildings, structures, geographic terrain, or", "(voice/data) or 4g (data) network congestion weather buildings, structures, geographic terrain, or tunnels warning: ignoring the rearview mirror light could mean you will not have sos call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be", "to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber.  Never place anything on or near the vehicle\u2019s LTE (voice/data) or 4G (data) and GPS antennas.  You could prevent LTE (voice/data) or 4G (data) and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable LTE (voice/data) or 4G (data) network connection and a GPS signal is required for the SOS Call system to function properly.  Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press", "Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the", "km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam", "in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up", "trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  Front View Camera When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.", "ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be", "may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades seeCAUTION: Never use Non-Detergent Oil or", "occur.  For the recommended viscosity and quality grades seeCAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.", "Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety", "any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province,", "including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where", "Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html frequently asked questions about installing child restraints with seat belts what is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child", "anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward-facing child restraint, up to the recommended weight limit of the child restraint.  Can the rear-facing child restraint touch the back of the front passenger seat?  Yes contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.  Can the rear head restraints be removed?  Yes the center head restraint can be removed if it interferes with the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint?  No do not twist the buckle stalk in a seating position with an alr retractor.  Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the", "and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.  Use this simple 5-step test to decide whether the child can use the vehicle\u2019s seat belt alone: Can the child sit all the way back against the back of the vehicle seat?  Do the child\u2019s knees bend comfortably over the front of the vehicle seat while the child is still sitting all the way back?  Does the shoulder belt cross the child\u2019s shoulder between the neck and arm?  Is the lap part of the belt as low as possible, touching the child\u2019s thighs and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to any of these questions was \u201cno,\u201d then the child still needs to use a booster seat in this vehicle.  If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s squirming or slouching can move the belt out of position.  If the shoulder belt contacts the", "squirming or slouching can move the belt out of position.  If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.  WARNING: Never allow a child to put the shoulder belt under an arm or behind their back.  In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.  A child must always wear both the lap and shoulder portions of the seat belt correctly.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.", "is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  Vehicle info push and release the up or down arrow button until the vehicle info menu icon is displayed in the instrument cluster display.  Push and release the left or right arrow button to scroll through the information submenus and push and release the ok button to select or reset the resettable submenus.  Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become", "been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  When the Display button is pressed on the touchscreen, the system will display the options related to the theme (if equipped), brightness, and color of the touchscreen.  The available settings are: note: depending on the vehicle\u2019s options, feature settings may vary.  MAX A/C Button Press and release the MAX A/C button on the touchscreen to change the current setting to the coldest output of air.  MAX A/C sets the control for maximum cooling performance.  The MAX A/C indicator illuminates when MAX A/C is on.  Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.  Note: The MAX A/C button is only available on the touchscreen.", "Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after", "disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Maintenance-Free Battery Your vehicle is equipped with a", "wheel well for the front passenger wheel.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt", "the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If", "batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Closing The Hood To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.", "rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  WARNING: Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.", "In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance", "abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.", "API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to", "you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov .  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c.20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause", "an authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.", "ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the", "duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and", "climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Diesel Fuel Specifications This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for", "to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with", "for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  CAUTION: If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage  ENGINE", "NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty", "and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.", "To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independentlyBe sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped)  To fold the seat bottom upward, proceed as follows: The rear seat bottoms can be folded upward into the Stadium Position to create more storage space on the vehicle\u2019s floor, and to access the under seat storage bins (if equipped).  The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The", "60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped) Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Lift upward on each section of the seat bottom.  Lift From Beneath Seat (Left Side Shown) Raise the seat bottom upward into the Stadium Position.  60/40 Split Folding Rear Seat The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.", "The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped)WARNING: The seatback is not intended to be used for storing cargo when folded flat, and only folds to allow access to the cargo area behind the seat.  Do not operate the vehicle with unsecured cargo on the second row folded seatback.  Note: Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.  In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not", "seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.  Be sure everyone in your vehicle is in a seat and using a seat belt properly.", "If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire", "will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.", "while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across", "the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the gvwr \"\u21e8vehicle loading\" .  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating", "and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.", "Upper Door Adjustment After installation of the half-doors, if water leaks or wind noise is observed, the seal of the upper half-door to the door opening may need to be adjusted.  To determine if the upper half-door needs to be adjusted, proceed as follows: Determine which door is affected.  Open the affected door and hold a dollar-size piece of paper along the top of the door opening against the vehicle near where the leak/noise was observed.  Make sure half of the paper is above the area where the door seal contacts the door opening, while the other half is below.  Close the door on the paper, then pull the paper upward.  If the paper moves with little to no effort, the upper half-door will need to be adjusted in that area to increase seal compression.  Performing A Paper Test There is another optional test that can be performed using a flashlight and the help of another person.  One person should be inside the vehicle, and move the flashlight around the periphery of the door seal, shining outward.  The", "the vehicle, and move the flashlight around the periphery of the door seal, shining outward.  The other person should stand outside of the vehicle and check for light passing by the seal.  If light is seen through the seal area, the door will need to be adjusted.  To adjust the seal compression, proceed as follows: Open the door and lift the upper half-door up and away from the lower half.  Lay the upper half-door on a clean, dry surface.  Using an 8 mm open-end wrench (not provided), loosen the nut located inside the bottom of the upper half-door post, closest to where the \u201cpaper test\u201d detected a gap.  Nut location inside bottom of post using a 3 mm allen wrench (not provided), rotate the screw on the side of the post counterclockwise (while holding the wrench on the loosened bolt) to increase the seal compression.  If needed, rotate clockwise to reduce seal compression.  Rotate screw for seal compression 1 \u2014 3 mm allen wrench 2 \u2014 8 mm open-end wrench tighten the nut inside the bottom of the post using the", "3 mm allen wrench 2 \u2014 8 mm open-end wrench tighten the nut inside the bottom of the post using the wrench and make sure the screw head is flush to the post.  Reinstall the upper half-door.  Screw head flush to post close the door and repeat the \u201cpaper test\u201d.  Repeat the adjustment procedure if needed.  If needed, add the provided shim to a lower half-door pocket to seal the upper half-door to the roof: lift upper half-door up and away from lower half.  Clean the bottom of the door pocket.  Remove upper half-door & clean bottom of door pocket slide the shim onto a pencil or similar tool.  Remove the paper backing from the adhesive side of the shim and place the shim with pencil into the pocket.  Press the shim firmly to the bottom of the pocket, and remove the pencil once the shim is firmly in place.  Press shim firmly into bottom of pocket 1 \u2014 remove paper backing from shim 2 \u2014 slide pencil through hole in shim 3 \u2014 press pencil with shim into pocket replace upper half-door.  Note: If the compression is", "shim 3 \u2014 press pencil with shim into pocket replace upper half-door.  Note: If the compression is increased too much on the front upper corner of the rear doors, deformation of the seal will occur.  Half-Door Installation To install the front or rear half-doors, proceed as follows: Remove the full doors from the vehicle.  For front door removal, see For rear door removal, see Locate the upper and lower hinge pins on the lower half-door, and lower them into the body hinges on the vehicle.  Note: the upper hinge pin is longer, which can be used to assist in guiding the door into place during installation.  Lower half-door hinge pins insert the upper and lower hinge pin screws into the body hinges.  Tighten the screws using a #T50 Torx head driver to 3.8 ft\u00b7 lb / 5.2 N\u00b7m.  Caution: do not close the door before reattaching the door check to the body.  Damage may occur to the door check.  Do not overtighten Torx fasteners, damage to the vehicle\u2019s parts will occur.  Hinge pins can break if overtightened during", "fasteners, damage to the vehicle\u2019s parts will occur.  Hinge pins can break if overtightened during door install (Max Torque: 6.0 ft\u00b7 lb/8.1 N\u00b7m).  Attach the cloth strap of the lower half-door to the metal hook just inside the vehicle.  Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap connect the wiring harness on the lower half-door to the connection just inside the vehicle.  Note: for front doors, make sure the wiring harness is closed completely.  Front door wiring harness 1 \u2014 open wiring harness 2 \u2014 closed wiring harness replace wiring access doors.  When the half-doors are shipped with the vehicle, the lower half-doors will have plugs in the post holes that must be removed prior to upper half-door installation.  To remove these plugs, proceed as follows: locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place tool into service hole of plug to remove using the tool,", "recommended) in the service hole.  Place tool into service hole of plug to remove using the tool, slowly pull upwards from the center of the plug to remove.  Making sure the window on the upper half-door is completely zipped closed, insert the upper half-door into the lower half-door by placing the posts into the post holes.  Lower the upper half-door into post holes push down firmly on the inside of the upper half-door until it is fully seated in the lower half.  Push Down To Fully Seat Upper Half-Door  Half-doors \u2014 if equipped half-doors \u2014 if equipped \u00b9 use this qr code to access your digital experience.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  CAUTION: Do not run half-doors through an automatic car wash.  This may result in scratches and wax buildup on the windows.  Careless handling and storage of the half-doors may", "in scratches and wax buildup on the windows.  Careless handling and storage of the half-doors may damage the seals resulting in water leaks into the interior of the vehicle.  The upper half-doors must be positioned properly to ensure sealing.  Improper installation can cause water leaks into the interior of the vehicle.  Store the zipper pulls of the upper half-door windows at the upper B-pillar area for both front and rear doors to avoid damage to the windows when not in use.  Do not attempt to operate the half-door zipper in temperatures of 41\u00b0F (5\u00b0C) or below.  Damage to the window may occur.", "Off-Road Driving Tips  DRIVING TIPS Off-Road Driving Tips Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result", "features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.", "Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada).  Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage Owner's Manuals, Radio Manuals and Warranty Information Books can be ordered through Archway at: To order the following manuals, you may use either the website or the phone numbers listed below.  Owner's Manuals If you do not read the entire Owner\u2019s Manual, you may miss important information.  Observe all Cautions and Warnings.  Owner's Manuals These Owner's Manuals have been prepared with the assistance", "and Warnings.  Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada) symbols key if you do not read the entire owner\u2019s manual, you may miss important information.  Observe all Cautions and Warnings.  Service Manuals These comprehensive Service Manuals provide a complete working knowledge of the vehicle, system, and/or components and is written in straightforward language with illustrations, diagrams, and charts.", "To engage REVERSE gear from the NEUTRAL position, lift the REVERSE ring, located below the knob and move the gear selector all the way left and then forward.  If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  To shift the gears, fully press the clutch pedal and place the gear selector into the desired gear position (the diagram for the engagement of the gears is displayed on the handle of the selector).  The gear position will be displayed in the instrument cluster.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to", "front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  Yellow indicator lights 4wd indicator light \"\u21e84wd indicator light \u2014 if equipped\" 4wd low indicator light \"\u21e84wd low indicator light \u2014 if equipped\" 4wd part time indicator light \"\u21e84wd part time indicator light \u2014 if equipped\" axle locker fault indicator light \"\u21e8axle locker fault indicator light \u2014 if equipped\" rear axle lock indicator light \"\u21e8rear axle lock indicator light \u2014 if equipped\" front and rear axle lock indicator light \"\u21e8front and rear axle lock indicator light \u2014 if equipped\" forward collision warning off indicator light \"\u21e8forward collision warning off indicator light \u2014 if equipped\" neutral indicator light \"\u21e8neutral indicator light \u2014 if equipped\" sway bar indicator light \"\u21e8sway bar indicator light \u2014 if equipped\" off road+ indicator light \"\u21e8off road+ indicator light \u2014 if equipped\" cargo", "light \u2014 if equipped\" off road+ indicator light \"\u21e8off road+ indicator light \u2014 if equipped\" cargo light on indicator light \"\u21e8cargo light on indicator light\" wait to start indicator light \"\u21e8wait to start indicator light \u2014 if equipped\" low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \"\u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped\" water in fuel indicator light \"\u21e8water in fuel indicator light \u2014 if equipped\" selec speed control (ssc) indicator light \u2014 if equipped this light will turn on when selec speed control is activated.  Selec Speed Control is available in 4WD Low ONLY.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.", "Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a", "electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of", "and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Frequency Operated Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your", "To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.  FOBIK-Safe only executes in vehicles with Passive Entry.  There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made by a valid Passive Entry key fob while a door is open.  A lock request is made by the Passive Entry door handle while a door is open.  A lock request is made by the door panel switch while the door is open.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  Note: The vehicle will only unlock the doors", "described in this section remains active/functional.  Note: The vehicle will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle.  The vehicle will not unlock the doors when any of the following conditions are true: A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are manually locked using the door lock knobs.  Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.", "Transmission function is monitored electronically for abnormal conditions.  If a condition is detected that could result in transmission damage, Transmission Limp Home mode is activated.  In this mode, the transmission may operate only in certain gears, or may not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some situations, the transmission may not re-engage if the engine is turned off and restarted.  The Malfunction Indicator Light (MIL) may be illuminated.  A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary.  It is important to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only manufacturer's specified transmission fluid It is important to maintain the transmission fluid at the correct level using the recommended fluid.  Using a transmission fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission", "fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  Using a lower gear while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  This action will also provide better engine braking.  Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle When frequent transmission shifting occurs (such as when", "Towing For Towing A Disabled Vehicle When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing a heavy trailer), use the AutoStick shift control to select a lower gear Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to", "or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  During cold weather, you may experience increased effort in shifting until the transmission fluid warms up.  This is normal.  Routine fluid and filter changes are not required.  However, change the fluid and filter if the fluid becomes contaminated (with water, etc.  ), or if the transmission is disassembled for any reason.  Automatic Transmission \u2014 If Equipped  Transmission Limp Home Mode Transmission function is monitored electronically for abnormal conditions.  If a condition is detected that could result in transmission damage, Transmission Limp Home mode is activated.  In this mode, the transmission may operate only in certain gears, or may not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some", "not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some situations, the transmission may not re-engage if the engine is turned off and restarted.  The Malfunction Indicator Light (MIL) may be illuminated.  A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary.  In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following steps: Even if the transmission can be reset, we recommend that you visit an authorized dealer at your earliest possible convenience.  An authorized dealer has diagnostic equipment to assess the condition of your transmission.  If the transmission cannot be reset, authorized dealer service is required.  Stop the vehicle.  Shift the transmission into PARK, if possible.  If not, shift the transmission to NEUTRAL.  Push and hold the ENGINE START/STOP button until the engine turns off.  Wait approximately 30", "Push and hold the ENGINE START/STOP button until the engine turns off.  Wait approximately 30 seconds.  Restart the engine.  Shift into the desired gear range.  If the problem is no longer detected, the transmission will return to normal operation.  Note: In cases where the instrument cluster message indicates the transmission may not re-engage after engine shutdown, perform this procedure only in a desired location (preferably, at an authorized dealer).", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press", "Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the", "km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam", "in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD", "Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button", "is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an", "SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too", "gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat,", "the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce", "off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on,", "while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system", "vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.", "If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the", "parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  When the parking brake is applied", "illuminate, have the light inspected by an authorized dealer.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  If the headlights or parking lights are left on after the ignition is placed in the OFF position, the vehicle will chime when the driver\u2019s door is opened.  Vehicle parking brake is applied Stability event occurs Gear selector is moved out of DRIVE Engine overspeed occurs Clutch pedal is pressed (manual transmission only) Vehicle is operating at a low RPM (manual transmission only) Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before", "crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  release the parking brake  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.", "in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not", "properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on", "functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been", "a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.", "Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset", "section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main", "WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will", "Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely", "two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.", "instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If", "if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.", "may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or", "will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the", "when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the", "with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It", "a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel", "is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d,", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.", "Potential signs of vehicle overheating: Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant", "Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine", "heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four", "will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the", "Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It", "with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to", "with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you", "off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool;", "upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service", "To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security", "Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped)Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the", "armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open", "arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second", "action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.", "Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts", "Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners", "careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it", "bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  Bumper end caps are removable on steel bumpers only.  The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 Bolt #2 Remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be", "lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step Two 1 \u2014 Hex Bolt Cover Installed 2 \u2014 Hex Bolt Cover Removed Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step Six Secure the windshield by passing a cinch strap through", "tie-down bumpers (if equipped).  Step Six Secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Do Not Overtighten!  Damage to the windshield could result.  Open the fuel filler door.  Fuel Filler Door Remove the fuel cap by rotating it counterclockwise.  Fuel Filler Cap Fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is", "\"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if", "below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.", "Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery", "If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see", "both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a", "the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect,", "death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  The positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Your vehicle may be equipped with a secondary battery used", "a \u201cfast charger\u201d to provide starting.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not", "not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.", "In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L 4H The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only", "at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  4H This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.", "surfaced roads.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the", "components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.", "WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been", "the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that", "WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.", "Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.  Do not open or close the Sunrider\u00ae top while driving.  Operating the top while driving could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice", "according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the", "heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the", "pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.", "Off-Road Driving Tips  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.", "areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire", "match those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could", "than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw", "accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is", "center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.", "The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force", "equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of", "maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Anti-Lock Brake System (ABS) The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking", "time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the abs activates: abs motor noise or clicking sounds (you may continue to hear for a short time after the stop) brake pedal pulsations a slight drop of the brake pedal at the end of the stop note: the abs is designed to function with the original equipment manufacturer (oem) tires.  Modification may result in degraded ABS performance.  WARNING: The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of", "or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS", "user\u2019s safety or the safety of others.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Anti-Lock Brake System (ABS) Warning Light This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  If the ABS light remains on or turns on", "position and may stay on for as long as four seconds.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying", "help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  If the ABS Warning Light remains on or comes on while", "the likelihood of ABS activation(s).  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be", "can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  The ABS is designed to function with the Original Equipment Manufacturer (OEM) tires.  Modification may result in degraded", "function with the Original Equipment Manufacturer (OEM) tires.  Modification may result in degraded ABS performance.  Your vehicle is equipped with an advanced Electronic Brake Control (EBC) system.  This system includes Anti-Lock Brake System (ABS), Brake Assist System (BAS), Electronic Brake Force Distribution (EBD), Electronic Roll Mitigation (ERM), Electronic Stability Control (ESC), Hill Start Assist (HSA), and Traction Control System (TCS).  These systems work together to enhance both vehicle stability and control in various driving conditions.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn", "alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals:", "the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.", "minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system", "from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or", "(CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, see These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the", "Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeThis remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN", "disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish", "this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  When Remote Start is active, and the outside ambient temperature is 40\u00b0F (4.5\u00b0C) or below, the system will automatically activate front defrost for 15 minutes or less.  The time is dependent on the ambient temperature.  Once the timer expires, the system will automatically adjust the settings depending on ambient conditions.  See \u201cRemote Start Comfort Systems \u2014 If Equipped\u201d in the next section for detailed operation.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15", "Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.", "your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil", "to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no", "completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator", "within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To", "this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will", "(805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on", "system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water", "free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  CAUTION: If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage Diesel Fuel Specifications This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill", "diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces", "Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use", "or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low", "or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use", "diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We", "must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that", "Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  Open the fuel filler door.  Fuel Filler Door Remove the diesel fuel filler cap by rotating it counterclockwise.  Fuel and Diesel Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the vehicle with fuel.  When the nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel filler door.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or", "Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan", "For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel", "requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust", "the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to", "ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Safety Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.  WARNING: Improperly inflated tires are dangerous and can cause collisions.  Underinflation increases tire flexing and can result in overheating and tire failure.  Overinflation reduces a tire's ability to cushion shock.  Objects on the road and chuckholes can cause damage that result in tire failure.  Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.  Unequal tire pressures can cause steering problems.  You could lose control of your vehicle.  Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.  Always drive with each tire", "to the other can cause the vehicle to drift to the right or left.  Always drive with each tire inflated to the recommended cold tire inflation pressure.  Note: Unequal tire pressures from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure from side to side may cause the vehicle to drift left or right.  FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out", "vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.", "Crossing A Ravine, Gully, Ditch, Washout Or Rut When crossing a ravine, gully, ditch, washout or a large rut, the angled approach is the key to maintaining your vehicle's mobility.  Approach these obstacles at a 45-degree angle and let each tire go through the obstacle independently.  You need to use caution when crossing large obstacles with steep sides.  Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover.  If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires.  Use the removed dirt to fill the rut ahead of the turnout you just created.  You should now be able to drive out following the trench you just created at a 45-degree angle.  WARNING: There is an increased risk of rollover when crossing an obstacle, at any angle, with steep sides.  When crossing a ravine, gully, ditch, washout or a large rut, the angled approach is the key to maintaining your vehicle's mobility.", "washout or a large rut, the angled approach is the key to maintaining your vehicle's mobility.  Approach these obstacles at a 45-degree angle and let each tire go through the obstacle independently.  You need to use caution when crossing large obstacles with steep sides.  Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover.  If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires.  Use the removed dirt to fill the rut ahead of the turnout you just created.  You should now be able to drive out following the trench you just created at a 45-degree angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something", "rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION:", "abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.", "Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the", "form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited", "This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system", "of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use", "or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling,", "to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential seeBulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes", "Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Fuel Oxidation Stability \u2014 Must Use Fuel Within Six Months Of Manufacture Biodiesel fuel has poor oxidation stability which can result in long term storage problems.  Fuel produced to approved ASTM standards, if stored properly, provides for protection against fuel oxidation for up to six months.", "To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note:", "(NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Note: depending on the vehicle\u2019s options, feature settings may vary.  Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and", "Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the", "ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will", "the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC positionIf the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle", "is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.", "Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution", "of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of", "all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.", "The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Retrieve funnel from under the right rear seat.  Fuel Funnel Location Refueling Funnel Remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting Funnel Ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from", "an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Emergency Gas Can Refueling Most gas cans will not", "cause the clutch to overheat and cause a fire.  Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of", "or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  REFUELING IN EMERGENCY \u2013 IF EQUIPPED The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Note: In certain cold conditions, ice may prevent the fuel door from opening.  If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button.  Do not pry on the door.  Emergency Gas Can Refueling Most gas cans will not", "inside release button.  Do not pry on the door.  Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of", "or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)", "Redundant Air Bag Warning Light If a fault with the Air Bag Warning Light is detected, which could affect the Supplemental Restraint System (SRS), the Redundant Air Bag Warning Light will illuminate on the instrument panel.  The Redundant Air Bag Warning Light will stay on until the fault is cleared.  In addition, a single chime will sound to alert you that the Redundant Air Bag Warning Light has come on and a fault has been detected.  If the Redundant Air Bag Warning Light comes on intermittently or remains on while driving have an authorized dealer service the vehicle immediately.  See \"\u21e8air bag warning light\" for more information regarding the redundant air bag warning light.  The warning display will turn on indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an", "is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with", "dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  This warning light will illuminate when the Stop/Start system is not functioning properly and service is required.  Contact an authorized dealer for service.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is", "Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The Air Bag Warning Light will turn on for four to eight", "have the problem diagnosed and corrected.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Ignoring the Air Bag Warning Light in", "an authorized dealer service the air bag system immediately.  Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bags to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Placing an object on the floor under the front passenger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision.  Do not place any objects on the floor under the front passenger seat.  If there is a fault present in the OCS, both the PAD Indicator Light and the Air Bag Warning Light will illuminate to show that the Passenger Advanced Front Air Bag is deactivated.  Should this occur, the Passenger Advanced Front Air Bag will remain deactivated until the fault is cleared.  This indicates that you should take the vehicle to an authorized dealer for", "the fault is cleared.  This indicates that you should take the vehicle to an authorized dealer for service immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light will illuminate whenever the ocs is unable to classify the front passenger seat status.  A malfunction in the OCS may affect the operation of the air bag system.  If the air bag warning light does not come on, or stays on after you start the vehicle, or it comes on as you drive, take the vehicle to an authorized dealer for service immediately.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will", "switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.", "Fastener Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  To remove the Fastener Bin: Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Note: The soft top fasteners do not go in the Fastener Bin.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  To remove the Fastener Bin: Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Your vehicle is equipped with a", "Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  Remove the grommets under the front seat (one left and one right).  Carpet Split Then pull the carpet out, to the rear and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin (if equipped), by removing the four bolts that hold it to the floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then lift the assembly out from under the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear Retainers Remove carpet from the vehicle.  When reinstalling the carpet, perform these", "Rear Retainers Remove carpet from the vehicle.  When reinstalling the carpet, perform these steps in reverse order making sure that the carpet is tucked under the scuffs, B-pillar, console, and then refasten the grommets.  Inside the bin are three removable dividers to set up storage that works best for you.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  The rear wall netting can be accessed the same way as the rear wall storage bin.  If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  Rear Wall Storage Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of", "is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  Fastener Bin Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.", "Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Lowering the windshield before completing the", "windshield is raised prior to installing the tops.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center", "windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Raise the hood slightly, and place a hand palm-side down in the center of the", "the lifted position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Release both of the outside hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  1 \u2014 Pull For Windshield Washer 2 \u2014 Rotate For Wiper Operation 3 \u2014 Push Up For Mist The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.", "Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.  When TSC is functioning, the ESC Activation/Malfunction Indicator Light will flash, the engine power may be reduced, and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying.  TSC is disabled when the ESC system is in the \u201cPartial Off\u201d or \u201cFull Off\u201d modes.  Note: TSC cannot stop all trailers from swaying.  Always use caution when towing a trailer and follow the trailer tongue weight recommendations.  See \"\u21e8trailer towing\" for further information.  WARNING: If TSC activates while driving, slow the vehicle", "towing\" for further information.  WARNING: If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway.  Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To", "or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.", "Door Latch Alignment If the door does not center align between the latch and the striker, proceed as follows: Loosen (do not remove) the four bolts on the door hinges using the provided #T50 Torx head driver.  Hinge bolt locations with the bolts loose, hold the door in the almost closing position, and check that the latch and striker align.  With the latch and striker aligned, proceed to close the door softly and tighten the hinge bolts to 20.3 ft\u00b7 lb / 27.5 N\u00b7m (Max Torque: 27.3 ft\u00b7 lb / 37 N\u00b7m).  CAUTION: Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  Note: Only adjust the door to fit correctly against the striker.  DO NOT adjust the striker, as this could affect the positioning of the full door.  Upper Door Adjustment After installation of the half-doors, if water leaks or wind noise is observed, the seal", "Adjustment After installation of the half-doors, if water leaks or wind noise is observed, the seal of the upper half-door to the door opening may need to be adjusted.  To determine if the upper half-door needs to be adjusted, proceed as follows: Determine which door is affected.  Open the affected door and hold a dollar-size piece of paper along the top of the door opening against the vehicle near where the leak/noise was observed.  Make sure half of the paper is above the area where the door seal contacts the door opening, while the other half is below.  Close the door on the paper, then pull the paper upward.  If the paper moves with little to no effort, the upper half-door will need to be adjusted in that area to increase seal compression.  Performing A Paper Test There is another optional test that can be performed using a flashlight and the help of another person.  One person should be inside the vehicle, and move the flashlight around the periphery of the door seal, shining outward.  The other person", "and move the flashlight around the periphery of the door seal, shining outward.  The other person should stand outside of the vehicle and check for light passing by the seal.  If light is seen through the seal area, the door will need to be adjusted.  To adjust the seal compression, proceed as follows: Open the door and lift the upper half-door up and away from the lower half.  Lay the upper half-door on a clean, dry surface.  Using an 8 mm open-end wrench (not provided), loosen the nut located inside the bottom of the upper half-door post, closest to where the \u201cpaper test\u201d detected a gap.  Nut location inside bottom of post using a 3 mm allen wrench (not provided), rotate the screw on the side of the post counterclockwise (while holding the wrench on the loosened bolt) to increase the seal compression.  If needed, rotate clockwise to reduce seal compression.  Rotate screw for seal compression 1 \u2014 3 mm allen wrench 2 \u2014 8 mm open-end wrench tighten the nut inside the bottom of the post using the wrench and", "wrench 2 \u2014 8 mm open-end wrench tighten the nut inside the bottom of the post using the wrench and make sure the screw head is flush to the post.  Reinstall the upper half-door.  Screw head flush to post close the door and repeat the \u201cpaper test\u201d.  Repeat the adjustment procedure if needed.  If needed, add the provided shim to a lower half-door pocket to seal the upper half-door to the roof: lift upper half-door up and away from lower half.  Clean the bottom of the door pocket.  Remove upper half-door & clean bottom of door pocket slide the shim onto a pencil or similar tool.  Remove the paper backing from the adhesive side of the shim and place the shim with pencil into the pocket.  Press the shim firmly to the bottom of the pocket, and remove the pencil once the shim is firmly in place.  Press shim firmly into bottom of pocket 1 \u2014 remove paper backing from shim 2 \u2014 slide pencil through hole in shim 3 \u2014 press pencil with shim into pocket replace upper half-door.  Note: If the compression is increased too", "pencil with shim into pocket replace upper half-door.  Note: If the compression is increased too much on the front upper corner of the rear doors, deformation of the seal will occur.  Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  How To Engage The Automatic Locking Mode Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  This indicator will illuminate when a door is ajar/open and not fully closed.", "To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then, adjust it to the appropriate height using the adjustment button.  For information on child seat tether routing, see A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  Do not drive the vehicle without the rear seat head restraints", "the vehicle or occupying a seat.  Do not drive the vehicle without the rear seat head restraints installed while passengers are occupying the rear seat.  In a collision, people riding in this area without the head restraints installed are more likely to be seriously injured or killed.  A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate", "put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  To remove the center head restraint, raise it as far as it can go.  Then, push the adjustment button and the release button at the base of each post while pulling the head restraint up.  A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  To raise the head restraint, pull upward on the head restraint.  To lower the head restraint, push the adjustment button located on the base of the head restraint, and push downward on the head restraint.  The release button does not need to be pushed to adjust the head restraint.  Front Head Restraints", "The release button does not need to be pushed to adjust the head restraint.  Front Head Restraints To raise the head restraint, pull upward on the head restraint.  To lower the head restraint, push the adjustment button located on the base of the head restraint, and push downward on the head restraint.  The release button does not need to be pushed to adjust the head restraint.  To remove the head restraint, raise it as far as it can go, then push the adjustment button and the release button at the base of each post while pulling the head restraint up.  To reinstall the head restraint, put the head restraint posts into the holes and push downward.  Then adjust it to the appropriate height.  WARNING: A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle.  Always securely stow removed head restraints in a location outside the occupant compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the", "compartment.  ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.  Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.  Note: Do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head.", "Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.  If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill,", "hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you", "straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a", "at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.", "Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  Do Not Operate The Engine With Low Oil Pressure If the Low Oil Pressure Warning Light turns on while driving, stop the vehicle and shut down the engine as soon as", "Pressure Warning Light turns on while driving, stop the vehicle and shut down the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the lamp.  If the lamp is still illuminated, shut the engine off, contact an authorized dealer, and do not operate the vehicle until the cause is corrected.  If the lamp is no longer illuminated, the engine can be operated, but should be taken to an authorized dealer as soon as possible for further inspection.  Note: Do not operate the vehicle until the cause is corrected.  This light does not show how much oil is in the engine.  The engine oil level must be checked under the hood.  CAUTION: If oil pressure falls to less than normal readings, shut the engine off immediately.  Failure to do so could result in immediate and severe engine damage.  Checking Oil Level To ensure proper engine lubrication, the engine oil must be maintained at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best", "at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off.  Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.  There are four possible dipstick types: Crosshatched zone.  Crosshatched zone marked SAFE.  Crosshatched zone marked with MIN at the low end of the range and MAX at the high end of the range.  Crosshatched zone marked with dimples at the MIN and the MAX ends of the range.  Adding 1 qt (1 L) of oil when the reading is at the low end of the dipstick range will raise the oil level to the high end of the range marking.  Note: Always maintain the oil level within the crosshatch markings on the dipstick.  CAUTION: Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure.  This could damage your engine.  Warm up the engine before placing it under load.  Do not operate the engine at", "damage your engine.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  This warning light will illuminate, and a chime will sound, to indicate", "an authorized dealer.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do Not Operate The Engine With Low Oil Pressure If the Low Oil Pressure Warning Light turns on while driving, stop the vehicle and shut down the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the lamp.  If the lamp is still illuminated, shut the engine off, contact an authorized dealer,", "the lamp.  If the lamp is still illuminated, shut the engine off, contact an authorized dealer, and do not operate the vehicle until the cause is corrected.  If the lamp is no longer illuminated, the engine can be operated, but should be taken to an authorized dealer as soon as possible for further inspection.  Note: Do not operate the vehicle until the cause is corrected.  This light does not show how much oil is in the engine.  The engine oil level must be checked under the hood.  CAUTION: If oil pressure falls to less than normal readings, shut the engine off immediately.  Failure to do so could result in immediate and severe engine damage.", "This vehicle is equipped with an Intelligent Battery Sensor (IBS) to perform additional monitoring of the electrical system and status of the vehicle battery.  1 \u2014 Supplemental Negative Battery Cable 2 \u2014 Main Negative Battery Cable 3 \u2014 Main Negative Battery Terminal 4 \u2014 Intelligent Battery Sensor (IBS) In cases when the IBS detects charging system failure, or the vehicle battery conditions are deteriorating, electrical load reduction actions will take place to extend the driving time and distance of the vehicle.  This is done by reducing power to or turning off non-essential electrical loads.  Battery Saver On, Battery Saver Mode Message, And Electrical Load Reduction Actions (If Equipped) This vehicle is equipped with an Intelligent Battery Sensor (IBS) to perform additional monitoring of the electrical system and status of the vehicle battery.  In cases when the IBS detects charging system failure, or the vehicle battery conditions are deteriorating, electrical load reduction actions will take place to", "vehicle battery conditions are deteriorating, electrical load reduction actions will take place to extend the driving time and distance of the vehicle.  This is done by reducing power to or turning off non-essential electrical loads.  Load reduction is only active when the engine is running.  It will display a message if there is a risk of battery depletion to the point where the vehicle may stall due to lack of electrical supply, or will not restart after the current drive cycle.  When load reduction is activated, the message \u201cBattery Saver On Some Systems May Have Reduced Power\u201d will appear in the instrument cluster.  These messages indicate the vehicle battery has a low state of charge and continues to lose electrical charge at a rate that the charging system cannot sustain.  The electrical loads that may be switched off (if equipped), and vehicle functions which can be affected by load reduction: heated seat/vented seats/heated wheel rear defroster and heated mirrors hvac system 115 volt ac power", "seat/vented seats/heated wheel rear defroster and heated mirrors hvac system 115 volt ac power inverter system audio and telematics system loss of battery charge may indicate one or more of the following conditions: the charging system cannot deliver enough electrical power to the vehicle system because the electrical loads are larger than the capability of the charging system.  The charging system is still functioning properly.  Turning on all possible vehicle electrical loads (e.g.  HVAC to max settings, exterior and interior lights, overloaded power outlets +12 Volt, 115 Volt AC, USB ports) during certain driving conditions (city driving, towing, frequent stopping).  Installing options like additional lights, upfitter electrical accessories, audio systems, alarms and similar devices.  Unusual driving cycles (short trips separated by long parking periods).  The vehicle was parked for an extended period of time (weeks, months).  The battery was recently replaced and was not charged completely.  The battery", "(weeks, months).  The battery was recently replaced and was not charged completely.  The battery was discharged by an electrical load left on when the vehicle was parked.  The battery was used for an extended period with the engine not running to supply radio, lights, chargers, +12 Volt portable appliances like vacuum cleaners, game consoles and similar devices.  Note: The charging system is independent from load reduction.  The charging system performs a diagnostic on the charging system continuously.  If the battery charge warning light is on it may indicate a problem with the charging system \"\u21e8battery charge warning light\" .  The ACC screen may display once again if any ACC activity occurs, which may include any of the following: This feature will only activate when the following conditions are met: The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may", "Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: Once SSC is enabled it will activate automatically once the following conditions are met: The following conditions must be met in order for HSA to activate:", "AutoPark will engage when all of these conditions are met: AutoPark will be disabled when operating the vehicle in 4WD LOW.  Autopark will engage only when vehicle speed is 1.2 mph (1.9 km/h) or less.  AutoPark will be disabled when operating the vehicle in 4WD LOW.  The message \u201c autopark disabled \u201d will be displayed in the instrument cluster.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an", "could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer", "must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Opening The Hood Release both of the outside hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood", "hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Note: Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If", "of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.", "The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring Height (H) Attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the", "approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  Service Forward Collision Warning (FCW) Light \u2014 If Equipped This warning light will illuminate to indicate a fault in the Forward Collision Warning System.", "This warning light will illuminate to indicate a fault in the Forward Collision Warning System.  Contact an authorized dealer for service Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.", "Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  It is the owner's responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system, please contact an authorized dealer.  Mixing engine coolant types is not recommended and can result in cooling system damage.  If HOAT and OAT coolant are mixed in an emergency, have an authorized", "in cooling system damage.  If HOAT and OAT coolant are mixed in an emergency, have an authorized dealer drain, flush, and refill with OAT coolant (conforming to MS.90032) as soon as possible.  Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been", "compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and", "into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Please review these recommendations for using Organic Additive Technology (OAT) engine coolant that meets the requirements of the manufacturer Material Standard MS.90032.  When adding engine coolant (antifreeze): The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  The tongue weight of the trailer The weight of any other type of cargo or equipment put in or on your vehicle The weight of the driver", "weight of any other type of cargo or equipment put in or on your vehicle The weight of the driver and all passengers For further information on GAWRs, vehicle loading, and trailer towing, see If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OAT coolant (conforming to MS.90032).  It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the Run Flat mode.  Disposal Of Used Coolant Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  Selection Of Coolant For further information Note: Mixing of engine", "assistance immediately.  Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not", "with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  ENGINE FLUIDS AND LUBRICANTS CAUTION: Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer", "flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Note: If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT)", "Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.", "engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.", "Maintenance Plan Refer to the maintenance plan for the required maintenance intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to prevent premature wear.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Maintenance Plan \u2014 Diesel Fuel Up To B5 Biodiesel Refer to the Maintenance Plans for required maintenance.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly", "ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Drain And Refill For the proper maintenance intervals  Maintenance Plan \u2014 Diesel Fuel Up To B5 Biodiesel Refer to the Maintenance Plans for required maintenance.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Maintenance Plan Refer to the maintenance plan for the required maintenance intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to", "intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to prevent premature wear.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.", "1 \u2014 Power Distribution Center (Fuses) 6 \u2014 Brake Fluid Reservoir Cap 2 \u2014 Battery 7 \u2014 Engine Air Cleaner Filter 3 \u2014 Engine Oil Dipstick 8 \u2014 Power Steering Fluid Reservoir Cap 4 \u2014 Engine Oil Fill 9 \u2014 Washer Fluid Reservoir Cap 5 \u2014 Engine Coolant Pressure Cap 1 \u2014 Battery 6 \u2014 Power Distribution Center (Fuses) 2 \u2014 Engine Oil Fill 7 \u2014 Power Steering Reservoir Cap 3 \u2014 Coolant Pressure Reservoir Cap 8 \u2014 Engine Oil Dipstick 4 \u2014 Brake Fluid Reservoir Cap 9 \u2014 Engine Air Cleaner Filter 5 \u2014 Washer Fluid Reservoir Cap Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Adding Washer Fluid The fluid reservoir is located in the engine compartment.  Be sure to check the fluid level at regular intervals.  Fill the reservoir with windshield washer", "Be sure to check the fluid level at regular intervals.  Fill the reservoir with windshield washer solvent only (not radiator antifreeze).  When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades; this will help blade performance.  To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate.  This rating information can be found on most washer fluid containers.  WARNING: Commercial windshield washer solvents are flammable.  They could ignite and burn you.  Care must be exercised when filling or working around the washer solution.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the", "Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off CAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.", "driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds", "REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the", "colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The", "or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Electric Power Steering (EPS) Fault Warning Light This warning light will turn on when there's a fault with the EPS system WARNING: Continued operation with reduced assist could pose a safety risk to yourself and others.  Service should be obtained as soon as possible.", "Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require", "coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  It is the owner's responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.  Some vehicles require special tools to add coolant properly.  Failure to fill these", "is operated.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system, please contact an authorized dealer.  Mixing engine coolant types is not recommended and can result in cooling system damage.  If HOAT and OAT coolant are mixed in an emergency, have an authorized dealer drain, flush, and refill with OAT coolant (conforming to MS.90032) as soon as possible.  Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant", "emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is", "damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Please review these recommendations for using Organic Additive Technology (OAT) engine coolant", "Please review these recommendations for using Organic Additive Technology (OAT) engine coolant that meets the requirements of the manufacturer Material Standard MS.90032.  When adding engine coolant (antifreeze): The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  The tongue weight of the trailer The weight of any other type of cargo or equipment put in or on your vehicle The weight of the driver and all passengers For further information on GAWRs, vehicle loading, and trailer towing, see If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OAT coolant (conforming to MS.90032).  It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the Run Flat mode.  Disposal Of Used Coolant Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To", "Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant", "an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  ENGINE FLUIDS AND LUBRICANTS CAUTION: Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine", "coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Note: If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel", "to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.", "There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  To reinstall the door(s), perform the previous steps in the reverse order.  Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop", "is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  Prior to off-road usage, the side steps should be removed to prevent damage.  There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt", "nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly With the help of a second person, set the Sunrider\u00ae top onto the top of the vehicle making sure to align the holes at the front and rear of the side rails.  Lower Sunrider\u00ae Onto The Vehicle Swing the front frame bracket around the side of the rail, and insert the door rail attachment bolt (provided bolt without spacer) from underneath.  Tighten with a #40 Torx head driver until snug.  Attach Front Door Rail Bolt Insert the rear door rail attachment bolt (provided bolt with spacer) from underneath.  Tighten with #40 Torx head driver until snug.  Attach Rear Door Rail Bolt Repeat", "from underneath.  Tighten with #40 Torx head driver until snug.  Attach Rear Door Rail Bolt Repeat steps 3 and 4 on the other side of the vehicle.  The recommended torque specification for the front and rear door rail attachment bolts is 8.8 ft-lb (12 N\u00b7m).  Attach the rear clamp at the rear center of the Sunrider\u00ae top using the two provided rear clamp attachment bolts.  Tighten with #40 Torx head driver until snug.  Rear Clamp Location The recommended torque specification for the rear clamp attachment bolts is 3.7 ft-lb (5 N\u00b7m).  From inside the vehicle, lift and pull the Sunrider\u00ae top forward using the integrated handle on the front header of the top.  Manually guide the top into the closed position.  Push Sunrider\u00ae Top Forward From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Pull the handle back upward while squeezing the hook, locking the latch into place.  Repeat on the other side.  Engage Both Header Latches Lug Nut/Bolt Torque **Lug Nut/Bolt", "place.  Repeat on the other side.  Engage Both Header Latches Lug Nut/Bolt Torque **Lug Nut/Bolt Size Lug Nut/Bolt Socket Size 130 ft-lb (176 N\u00b7m) M14 x 1.50 mm 22 mm After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  Side Step Removal \u2014 If Equipped There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener locations (one side) remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side", "Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side steps should be removed to prevent damage.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying", "this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced", "a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly", "not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.", "securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  External racks do not increase the total load carrying capacity of the vehicle.  Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, does not exceed the maximum vehicle load capacity.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full", "operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred,", "will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.", "operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped)Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a", "arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately", "Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.", "A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into", "the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Press and release this button to turn the Climate Control ON/OFF.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  To Turn Off The Engine Using The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C", "The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control will turn off, but Stability Control will remain active.  Hold the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner", "the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  A/C Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Note: For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the", "seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.", "Jack Location The jack and tools are stored under the right rear seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat.  Removing the wing bolt release the tool bag straps from the jack and remove tools from bag.  Jack and tool bag remove tool kit and assemble tools.  Jack And Tool Bag There are two ways to assemble the tools: Note: If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  CAUTION: The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools,", "and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools, always reinstall them in the original carrier and location.  While driving you may experience abrupt stopping, rapid acceleration or sharp turns.  A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an", "being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Side Step Removal \u2014 If Equipped There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener locations (one side) remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and", "each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side steps should be removed to prevent damage.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.", "lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.", "Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates", "and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs", "needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android", "the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its", "calls.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To", "Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the", "your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc. Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .", "Push and release the up or down arrow button until the fuel economy icon is highlighted in the instrument cluster display.  Push and hold the ok button to reset average fuel economy feature.  Toggle left or right to select a display with or without current fuel economy information.  Fuel Economy The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located  Vehicle info push and release the up or down arrow button until the vehicle info menu icon is displayed in the instrument cluster display.  Push and release the left or right arrow button to scroll through the information submenus and push and release the ok button to select or reset the resettable submenus.  The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is locatedSee the following", "symbol points to the side of the vehicle where the fuel filler door is locatedSee the following steps for refueling: If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a", "See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the", "Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can", "lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  To Reset The Manual Park Release: Pull upward on the tether strap, releasing it from the \u201clocked\u201d position.  Lower the Manual Park Release lever downward into its original position.  Original tether position tuck the tether strap into the base of the", "into its original position.  Original tether position tuck the tether strap into the base of the console, and reinstall the cover.  Extended Park Starting Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Note: Extended Park condition occurs when the vehicle has not been started or driven for at least 30 days.  CAUTION: To prevent damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.", "Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When", "if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so", "in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being", "be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx", "the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  60/40 Split Folding Rear Seat The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped)WARNING: The seatback is not intended to be used for storing cargo when folded flat, and only folds to allow access to the cargo area behind the seat.  Do not operate the vehicle with unsecured cargo on", "allow access to the cargo area behind the seat.  Do not operate the vehicle with unsecured cargo on the second row folded seatback.  Note: Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.  In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.  Be sure everyone in your vehicle is in a seat and using a seat belt properly.  The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  This vehicle has", "seatback.  Both seatbacks should be locked to limit access to items behind seat.  This vehicle has front air bags and lap/shoulder belts for both the driver and front passenger.  The front air bags are a supplement to the seat belt restraint systems.  The driver front air bag is mounted in the center of the steering wheel.  The passenger front air bag is mounted in the instrument panel, above the glove compartment.  The words \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d are embossed on the air bag covers.  This vehicle has an Occupant Classification System (\u201cOCS\u201d) in the front passenger seat.  The OCS is designed to activate or deactivate the Passenger Advanced Front Air Bag depending on the occupant\u2019s seated weight.  It is designed to deactivate the Passenger Advanced Front Air Bag for an unoccupied seat and for occupants whose seated weight classifies them in a category other than a properly seated adult.  This could be a child, teenager, or even an adult.  Cargo must be securely tied down before driving your vehicle.", "child, teenager, or even an adult.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.", "Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact", "background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected,", "will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to", "hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect", "two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.", "in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.", "PARKING BRAKE Before exiting the vehicle, make sure that the parking brake is fully applied.  Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or FIRST gear.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic", "to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  WARNING: Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake", "be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  CAUTION: If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the", "as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit", "could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally", "unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  When the parking brake is", "and fill as needed.  Check function of all interior and exterior lights.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the Brake Warning Light", "or that there is a problem with the Anti-Lock Brake System reservoir.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.", "ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are", "in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the", "starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:", "Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also", "under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  Bed Rail Tie Down Locations Your vehicle is equipped with the child restraint", "in the truck bed.  Bed Rail Tie Down Locations Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.  The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer", "provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Supplemental Seat-Mounted Side Air Bags (SABs) are located in the outboard side of the front seats.  The SABs are marked with a \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d on a label or on the seat trim on the outboard side of the seats.  Four auxiliary switches are located in the lower switch bank of the instrument panel and can be used to power various electrical devices.  1 \u2014 Retainers 2 \u2014 Fuel Filter Protective Cover The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.", "Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Maps Push and hold the VR button on the steering wheel until the beep or tap the Microphone icon to ask Apple\u00ae Siri to take you to a desired destination by voice.  You can also touch the", "icon to ask Apple\u00ae Siri to take you to a desired destination by voice.  You can also touch the Navigation icon in Apple CarPlay\u00ae to access Apple\u00ae Maps.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the", "to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the", "touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.", "To fold the seat bottom upward, proceed as follows: The rear seat bottoms can be folded upward into the Stadium Position to create more storage space on the vehicle\u2019s floor, and to access the under seat storage bins (if equipped).  The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped) Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Lift upward on each section of the seat", "the folded webbing and the seat belt is no longer twisted.  Lift upward on each section of the seat bottom.  Lift From Beneath Seat (Left Side Shown) Raise the seat bottom upward into the Stadium Position.  Rear Seat Stadium Position The rear seat bottoms can be folded upward into the Stadium Position to create more storage space on the vehicle\u2019s floor, and to access the under seat storage bins (if equipped).  To fold the seat bottom upward, proceed as follows: Lift upward on each section of the seat bottom.  Lift from beneath seat (left side shown) raise the seat bottom upward into the stadium position.  Stadium Position To return the seat bottom to the normal position, push downward on the raised seat bottom.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independentlyBe sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The", "are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped)", "If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.", "tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for", "Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons", "Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed", "is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from", "Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  Towing Requirements To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended: WARNING: Improper towing can lead to a collision.  Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel.  When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.  You could lose control of your vehicle and have a collision.  When hauling cargo, or towing a trailer, do not overload your vehicle or trailer.  Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or", "or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.  Safety chains must always be used between your vehicle and trailer.  Always connect the chains to the frame or hook retainers of the vehicle hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be parked on a grade.  When parking, apply the parking brake on the tow vehicle.  Put the tow vehicle transmission in PARK.  Always block or \"chock\" the trailer wheels.  GCWR must not be exceeded.  Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: gvwr gtw gawr tongue weight rating for the trailer hitch utilized caution: do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven.  The engine, axle or other parts could be damaged.  Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do", "the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.  This helps the engine and other parts of the vehicle wear in at the heavier loads.", "Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW", "temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring Height (H) Attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Trailer And Tongue Weight Never exceed the maximum tongue weight stamped on your bumper or trailer hitch.  Consider the following items when computing the weight on the", "on your bumper or trailer hitch.  Consider the following items when computing the weight on the rear axle of the vehicle: the tongue weight of the trailer the weight of any other type of cargo or equipment put in or on your vehicle the weight of the driver and all passengers note: remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.", "BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load", "cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from", "The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.", "The BSM system notifies the driver of objects in the detection zones by illuminating the BSM Warning Light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume.  See \"\u21e8blind spot modes\" for further information.  The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.  The BSM system will issue an alert during these types of zone entries.  When the BSM system is turned off there will be no visual or audible alerts from either the BSM or RCP systems.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft", "12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft (3 m) beyond the rear fascia/bumper of the vehicle.  The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas.  BSM Radar Location (Left Side Shown) The BSM system will store the current operating mode when the vehicle is shut off.  Each time the vehicle is started the previously stored mode will be recalled and used.  Blind Spot Monitoring (BSM) \u2014 If Equipped The BSM system uses two radar sensors, located inside the taillights, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.)  that enter the blind spot zones from the rear/front/side of the vehicle.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate", "mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft (3 m) beyond the rear fascia/bumper of the vehicle.  The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas.  The BSM system can become blocked if snow, ice, mud, or other road contaminations accumulate on the rear fascia/bumper where the radar sensors are located.  The system may also detect a blockage if the vehicle is operated in areas with extremely low radar returns, such as a desert, or parallel to a large elevation drop.  If a blockage is detected, a \u201cBlind Spot Temporarily Unavailable, Wipe Rear Corners\u201d message will display in the instrument", "a \u201cBlind Spot Temporarily Unavailable, Wipe Rear Corners\u201d message will display in the instrument cluster, both mirror lights will illuminate, and BSM and RCP alerts will be disabled.  This is normal operation.  The system will automatically resume function when the condition clears.  To minimize system blockage, do not block the area of the rear fascia/bumper where the radar sensors are located with foreign objects (bumper stickers, bicycle racks, etc.)  and keep it clear of road contaminations.  The BSM system notifies the driver of objects in the detection zones by illuminating the BSM Warning Light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume.  See \"\u21e8blind spot modes\" for further information.  The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.  The BSM system will issue an alert during these types of zone entries.  Note: The BSM system DOES NOT alert", "system will issue an alert during these types of zone entries.  Note: The BSM system DOES NOT alert the driver about rapidly approaching vehicles that are outside the detection zones.  The BSM system detection zone DOES NOT change if your vehicle is towing a trailer.  Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change.  If the trailer or other object (i.e., bicycle, sports equipment) extends beyond the side of your vehicle, this may result in the BSM Warning Light remaining illuminated the entire time the vehicle is in a forward gear.  See \"\u21e8uconnect settings\" for more information.  The Blind Spot Monitoring (BSM) system may experience dropouts (blinking on and off) of the side mirror warning indicator lights when a motorcycle or any small object remains at the side of the vehicle for extended periods of time (more than a couple of seconds).  ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster", "ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster displayIt provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.", "Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New", "and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage.", "accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet", "plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of", "vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Power Inverters \u2014 If Equipped There is a 115 V (400 W) maximum inverter outlet located on the back of the center console to convert Direct Current (DC) to Alternating Current (AC).  This outlet can power cellular phones, electronics and other low power devices requiring power up to 400 W. Certain video game consoles exceed this power limit, as will most power tools.  There may also be a second 115 V (400 W) maximum exterior power inverter located on the rear right side of the truck bed near the tailgate.  This inverter can be turned on by the Instrument Panel Power Inverter switch located to the left of the steering wheel.  This inverter can power cellular phones, electronics and other low power devices requiring power up to 400 W. Certain video game consoles exceed this limit, as will most power tools.  The", "power up to 400 W. Certain video game consoles exceed this limit, as will most power tools.  The indicator light on the power inverter switch will be illuminated when the inverter is turned on.  The power inverter is designed with built-in overload protection.  If the power rating of 400 W is exceeded, the power inverter automatically shuts down.  Once the electrical device has been removed from the outlet, the inverter should automatically reset.  Note: 400 W is the maximum for the inverter, not each outlet.  If two outlets are in use, 400 W is shared among the devices plugged in.  Note: The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  There", "when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners,", "the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.", "Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather.  To clear the windows, select Defrost or Mix mode and increase the front blower speed.  Do not use the Recirculation mode without A/C for long periods, as fogging may occur.  Do not use abrasive cleaning components, solvents, steel wool, or other aggressive material to clean the lenses.  The lenses in front of the instruments in this vehicle are molded in clear plastic.  When cleaning the lenses, care must be taken to avoid scratching the plastic.  Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as", "the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsTo minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.  To remove road dirt, wash with a mild soap solution followed by rinsing.  If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  If the \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the windshield and forward-facing camera inspected at an authorized dealer.", "obstruction, have the windshield and forward-facing camera inspected at an authorized dealer.  All glass surfaces should be cleaned on a regular basis with Mopar\u00ae Glass Cleaner, or any commercial household-type glass cleaner.  Never use an abrasive type cleaner.  Use caution when cleaning the inside rear window equipped with electric defrosters or windows equipped with radio antennas.  Do not use scrapers or other sharp instruments that may scratch the elements.  The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems are experienced.  This inspection should include the following points:  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer", "activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.", "Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the", "start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon", "the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Your vehicle is equipped with a sophisticated Onboard Diagnostic", "prevent vehicle registration.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will", "to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following:", "To Manually Turn On The Stop/Start System Push the Stop/Start Off switch (located on the switch bank).  The light on the switch will turn off.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the", "time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabledNote: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn On The Stop/Start System Push the Stop/Start Off switch (located on the switch bank).  The light on the switch will turn off.", "If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD", "(ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each", "braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot", "afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  The ABS is designed to function with the Original Equipment Manufacturer (OEM) tires.  Modification may result in degraded ABS performance.  Your vehicle is equipped with an advanced Electronic Brake Control (EBC) system.  This system includes Anti-Lock Brake System (ABS), Brake Assist System (BAS), Electronic Brake Force Distribution (EBD), Electronic Roll Mitigation (ERM), Electronic Stability Control (ESC), Hill Start Assist (HSA), and Traction Control System (TCS).  These systems work together to enhance both vehicle stability and control in various driving conditions.  The ABS is activated during braking when", "stability and control in various driving conditions.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS)", "may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency", "vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Anti-Lock Brake System (ABS) The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.", "cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the abs activates: abs motor noise or clicking sounds (you may continue to hear for a short time after the stop) brake pedal pulsations a slight drop of the brake pedal at the end of the stop note: the abs is designed to function with the original equipment manufacturer (oem) tires.  Modification may result in degraded ABS performance.  WARNING: The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting", "may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of", "in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Anti-Lock Brake System (ABS) Warning Light This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long", "on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.", "Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may", "the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap", "pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED) Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil", "as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause", "change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.", "law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in", "If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will", "Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact", "(UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "Emergency Tow Hooks \u2014 If Equipped If your vehicle is equipped with tow hooks, they are mounted in the front and the rear fascia/bumpers.  Note: Depending on vehicle trim level, rear tow hooks may vary.  WARNING: Do not use a chain for freeing a stuck vehicle.  Chains may break, causing serious injury or death.  Stand clear of vehicles when pulling with tow hooks.  Tow straps may become disengaged, causing serious injury.  CAUTION: Tow hooks are for emergency use only, to rescue a vehicle stranded off road.  Tow straps are recommended when towing the vehicle, chains may cause vehicle damage.  The tow hooks must not be used to move the vehicle off the road or where there are obstacles.  Do not use the tow hooks for tow truck hookup or highway towing.  Do not use the tow hooks to pull a vehicle onto a flatbed truck.  Do not use the tow hooks to free a stuck vehicle Damage to your vehicle may occur if these guidelines are not followed Manual Front Seatback Recline Adjustment To recline the seat, pull on the", "are not followed Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Rear Wall Storage Bin To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  Note: The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  To Reset The Manual Park Release: Pull upward on the tether strap, releasing it from the", "seat.  To Reset The Manual Park Release: Pull upward on the tether strap, releasing it from the \u201clocked\u201d position.  Lower the Manual Park Release lever downward into its original position.  Original tether position tuck the tether strap into the base of the console, and reinstall the cover.", "To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired", "times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide", "retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.", "VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both", "the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the", "If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your", "involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm", "one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system", "is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door.  Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.  Inflation pressure is measured in units of PSI (pounds per square inch) or kPa (kilopascals).  Maximum inflation pressure the maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire.  The maximum inflation pressure is molded into the sidewall.  Recommended cold tire inflation pressure the manufacturer\u2019s recommended cold tire inflation pressure as shown on the tire placard.  Tire placard a label permanently attached to the vehicle describing the vehicle\u2019s loading capacity, the original equipment tire sizes and the recommended cold tire inflation pressures.  Tire pressures change by approximately 1 psi (7 kPa) per 12\u00b0F (7\u00b0C)", "cold tire inflation pressures.  Tire pressures change by approximately 1 psi (7 kPa) per 12\u00b0F (7\u00b0C) of air temperature change.  Keep this in mind when checking tire pressure inside a garage, especially in the Winter.  Jacking and tire changing \u00b9 use this qr code to access your digital experience.  Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: At Every Oil Change Interval As Indicated By Oil Change Indicator System: Change oil and filter.  Rotate the tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on.  Inspect battery and clean and tighten terminals as required.  Inspect the CV/Universal joints.  Inspect brake pads, shoes, rotors, drums, hoses and parking brake.  Inspect engine cooling system protection and hoses.  Inspect exhaust system.  Inspect engine air cleaner filter if using in dusty or off-road conditions, replace engine air cleaner filter if necessary.  Inspect all door latches for presence", "conditions, replace engine air cleaner filter if necessary.  Inspect all door latches for presence of grease, reapply if necessary.  Do not continue driving with one or more flat tires as handling may be compromised.  Stop the vehicle, avoiding sharp braking and steering.  If a tire puncture occurs, repair immediately using the dedicated tire repair kit and contact an authorized dealer as soon as possible.  Consult an authorized tire dealer for tire repairs and additional information.  In the Selectable Tire Fill Alert application, which is located in the apps menu of the Uconnect system, you will be able to select a pressure setting for both the front and rear axle tire pressures by scrolling through a pressure range from XX to 15 psi in 1 psi increments for each axle setting.  After inspecting or adjusting the tire pressure, always reinstall the valve stem cap.  This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.  Check the inflation pressure of each tire,", "the valve stem, which could damage the valve stem.  Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.  Safety Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.  WARNING: Improperly inflated tires are dangerous and can cause collisions.  Underinflation increases tire flexing and can result in overheating and tire failure.  Overinflation reduces a tire's ability to cushion shock.  Objects on the road and chuckholes can cause damage that result in tire failure.  Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.  Unequal tire pressures can cause steering problems.  You could lose control of your vehicle.  Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.", "from one side of the vehicle to the other can cause the vehicle to drift to the right or left.  Always drive with each tire inflated to the recommended cold tire inflation pressure.  Note: Unequal tire pressures from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure from side to side may cause the vehicle to drift left or right.  FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of", "Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.", "Turn Signal Indicator Lights When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Note: A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.  Check for an inoperative outside light bulb if either indicator flashes at a rapid rate.  When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Lightly push the multifunction lever up or down, without moving beyond the", "the horn will chirp.  Lightly push the multifunction lever up or down, without moving beyond the detent, and the turn signal will flash three times then automatically turn off.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Turn Signal Indicator Lights When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Note: A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.  Check for an inoperative outside light bulb if either indicator flashes at a rapid rate.  Turn Signals Move the multifunction lever up or down to activate the turn signals.  The arrows on", "Turn Signals Move the multifunction lever up or down to activate the turn signals.  The arrows on each side of the instrument cluster flash to show proper operation.  Note: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.", "When activated, OFF ROAD+ is designed to improve the user experience when using specific Off Road driving modes.  To activate Off Road+, push the OFF ROAD+ switch in the switch bank.  The vehicle\u2019s performance will improve depending on which Four-Wheel Drive (4WD) mode is activated.  OFF ROAD+ Switch If equipped with Off Road+ and if Off Road+ is active when \"Full Off\" mode is enabled by the driver, ESC will not switch to \"Partial Off\" mode at any speed and will remain in \"Full Off\" mode until Off Road+ is exited or ESC is re-enabled by the driver.  OFF ROAD+ \u2014 If Equipped When activated, OFF ROAD+ is designed to improve the user experience when using specific Off Road driving modes.  To activate Off Road+, push the OFF ROAD+ switch in the switch bank.  The vehicle\u2019s performance will improve depending on which Four-Wheel Drive (4WD) mode is activated.  When off road+ is active, the following features will activate: the off road+ telltale will illuminate in the instrument cluster display a mode specific", "activate: the off road+ telltale will illuminate in the instrument cluster display a mode specific message will display the instrument cluster display off road pages will launch on the radio head-unit (if equipped) the off road camera will launch (if equipped) once in off road+, the vehicle will begin to behave in different ways depending on the 4wd mode in use.  The following enhancements will occur when using OFF ROAD+.  Note: OFF ROAD+ will not function in Two-Wheel Drive High (2H) mode.  If the button is pushed while in 2H mode, the cluster display will show the message \u201cOFF ROAD+ Unavailable Shift to 4WD\u201d.  Off Road+ Indicator Light \u2014 If Equipped This indicator light will illuminate when Off Road+ has been activated.", "Hill Climbing Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches", "trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of", "more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside", "ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all", "preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls,", "Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a", "brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using", "stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the", "or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire", "will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to", "top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to", "so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx", "the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Editing Your Notifications Notifications are an important element of your SiriusXM Guardian\u2122 account.  For example, any time you use your remote services (such as Remote Door Unlock), you can elect to receive a text message, push notification, and/or E-mail to notify you of the event.  To set up the notifications, please follow these instructions.  Log on to your owner\u2019s account at https://www.mopar.com/en-us.html (us residents) and select \u201cdashboard\u201d, or www.mopar.ca (canadian residents), select \u201cmy vehicle\u201d and then \u201cdashboard\u201d.  Click the Edit/Edit Profile button.  Once there, select \u201cSiriusXM Guardian\u2122\u201d where you can edit Notification Preferences.  You can enter a mobile phone and/or email address to notify you, and you can customize the types of messages.  Favorites Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  You can exit the Favorites Menu by a press of the X button.  The Favorites feature enables", "You can exit the Favorites Menu by a press of the X button.  The Favorites feature enables you to set a favorite artist or song that is currently playing.  The radio then uses this information to alert you when either the favorite artist or song is being played at any time by any of the SiriusXM\u00ae Channels.  The maximum number of favorites that can be stored in the Radio is 50.  Favorite artist: while the song is playing, to set a favorite artist, press the favorites button on the touchscreen and then the favorite artist button on the touchscreen.  Favorite song: while the song is playing, to set a favorite song, press the favorites button on the touchscreen and then the favorite song button on the touchscreen.  Using your owner\u2019s site your owner\u2019s site website https://www.mopar.com/en-us.html (us residents), or www.mopar.ca (canadian residents) provides you with all the information you need, all in one place.  You can track your service history, find recommended accessories for your vehicle, watch videos", "You can track your service history, find recommended accessories for your vehicle, watch videos about your vehicle's features, and easily access your manuals.  It is also where you can manage your SiriusXM Guardian\u2122 account.  This section will familiarize you with the key elements of the website that will help you get the most of your SiriusXM Guardian\u2122 connected services.  For customers in the United States, press the Sign In/Register button and enter your email address and password.  For customers in Canada, press the My Vehicle button.  Select from \u201cDashboard\u201d, \u201cVehicle Health Report\u201d, and \u201cRecalls\u201d.  The website will then prompt you to log in using your email address and password.  Edit/edit profile: to manage the details of your siriusxm guardian\u2122 account, such as your contact information, password and siriusxm guardian\u2122 pin, click on the edit/edit profile button to access the details of your account.  Connected services status: this statement will indicate your siriusxm guardian\u2122-equipped vehicle.", "Connected services status: this statement will indicate your siriusxm guardian\u2122-equipped vehicle.  Remote commands: for vehicles with an active siriusxm guardian\u2122 subscription, press one of these icons and enter your four-digit siriusxm guardian\u2122 security pin to remotely start (if equipped), lock/unlock doors or sound the horn and flash the lights.", "This is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer.  They want to know if you need assistance.  If an authorized dealer is unable to resolve the concern, you may contact FCA US LLC's Customer Assistance center.  FCA US LLC and its authorized dealers are vitally interested in your satisfaction.  We want you to be happy with our products and services.  Warranty service must be done by an authorized dealer.  We strongly recommend that you take the vehicle to an authorized dealer.  They know your vehicle the best, and are most concerned that you get prompt and high quality service.  FCA US LLC's authorized dealers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner.  This is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason", "is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer.  They want to know if you need assistance.  If an authorized dealer is unable to resolve the concern, you may contact FCA US LLC's Customer Assistance center.  We recommend seeing an authorized dealer for service.  An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  If the transmission cannot be reset, authorized dealer service is required.  WARRANTY INFORMATION See the Warranty Information for the terms and provisions of FCA US LLC warranties applicable to this vehicle and market.  Refer to www.mopar.com/om for further information.  See the Warranty Information for", "and market.  Refer to www.mopar.com/om for further information.  See the Warranty Information for the terms and provisions of FCA Canada Inc.warranties applicable to this vehicle and market.  Refer to www.owners.mopar.ca/en for further information.  Use this QR code to access your digital experience.", "Snow Tires Some areas of the country require the use of snow tires during the Winter.  Snow tires can be identified by a \u201cmountain/snowflake\u201d symbol on the tire sidewall.  If you need snow tires, select tires that are equivalent in size and type to the original equipment tires.  Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle.  Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h).  For speeds above 75 mph (120 km/h), refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures.  While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires.  Some states prohibit studded tires; therefore, local laws should be checked before using these tire types.  When stuck in mud, sand,", "therefore, local laws should be checked before using these tire types.  When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles", "is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your", "to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious", "when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.", "Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Biodiesel fuel may gel or solidify at low ambient temperatures, which may pose problems for both storage and operation.  Precautions can be necessary at low ambient temperatures, such as storing the fuel in a heated building or a heated storage tank, or using cold temperature additives.  Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Materials Added To Fuel Besides using", "economy, reduce emissions, and maintain vehicle performance.  Materials Added To Fuel Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Designated TOP TIER Detergent Gasoline contains a higher level of detergents to further aide in minimizing engine and fuel system deposits.  When available, the usage of TOP TIER Detergent Gasoline is recommended.  Visit www.toptiergas.com for a list of top tier detergent gasoline retailers.  Indiscriminate use of fuel system cleaning agents should be avoided.  Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients.  These can harm fuel system gasket and diaphragm materials.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline", "CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against", "tampering with the emissions control system can result in civil penalties being assessed against you.", "Secondary Method For Oil Change Reset Procedure Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Note: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.  If necessary, repeat this procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will", "may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the", "will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Secondary Method For Oil Change Reset Procedure Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Note: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.  If necessary, repeat this procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator", "in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil", "oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.", "your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil", "to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no", "completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator", "within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To", "this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will", "(805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on", "system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to", "of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances", "(if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle", "repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio.  This condition may be", "on in your vehicle can cause erratic or noisy performance from your radio.  This condition may be lessened or eliminated by repositioning the mobile phone within the vehicle.  This condition is not harmful to the radio.  If your radio performance does not satisfactorily improve from repositioning the mobile phone, it is recommended that the volume be turned down or off during mobile phone operation when not using the Uconnect system.  Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors.  Installing some form of aftermarket window tinting that affects radio wave signals.  Lots of snow or ice around the wheels or wheel housings.  Using tire chains on the vehicle.  Using wheels/tires not equipped with TPMS sensors.  The radio unit is acting as the amplifier for audio output from the Auxiliary device.  Therefore, if the volume control on the Auxiliary device is set too low, there will be insufficient audio signal for the radio unit to play the", "device is set too low, there will be insufficient audio signal for the radio unit to play the music on the device.", "BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load", "cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will", "load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on GAWRs, vehicle loading, and trailer towing, see Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not", "rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.", "The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  Front View Camera When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted", "the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering", "image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are", "for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera", "on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the", "exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other", "Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle", "Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.", "then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "Preserving The Bodywork  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to", "are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.", "If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).", "When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Child-Protection Door Lock Location  Child-Protection Door Lock System \u2014 Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a", "a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove the sealing plug for access, and use a flat-blade screwdriver (or mechanical key) to rotate the dial to the lock or unlock position.  Note: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a", "and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Note: Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the", "is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).", "Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.  Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue", "is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.", "Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Note: Vehicle speeds shown in the preceding chart are for 2H and 4H only.  Vehicle speeds in 4L would be significantly less.  Manual transmission shift speeds in mph (km/h) engine speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.6l accel.  15 (24) 24 (39) 50 (80) 65 (104) 70 (112) cruise 10 (16) 19 (31) 40 (64) 55 (88) 65 (105) 8\u2013speed automatic transmission the transmission gear range (prndm) is displayed both beside the gear selector and in the instrument cluster.  To select a gear range, push the lock button on the gear selector and move the selector rearward or forward.  To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.  You", "the transmission out of PARK, the engine must be running and the brake pedal must be pressed.  You must also press the brake pedal to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is stopped or moving at low speeds.  Select the DRIVE range for normal driving.  The electronically controlled transmission adapts its shift schedule based on driver inputs, along with environmental and road conditions.  The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt.  This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers).  Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped.  Be sure to keep your foot on the brake pedal when shifting between these gears.  The transmission gear selector provides PARK, REVERSE, NEUTRAL, DRIVE and MANUAL (AutoStick) shift positions.  Manual shifts can be made using the AutoStick shift control.  Toggling the gear", "shift positions.  Manual shifts can be made using the AutoStick shift control.  Toggling the gear selector forward (-) or rearward (+) while in the MANUAL (AutoStick) position (beside the DRIVE position) will manually select the transmission gear, and will display the current gear in the instrument cluster Note: In the event of a mismatch between the gear selector position and the actual transmission gear (for example, driver selects PARK while driving), the position indicator will blink continuously until the selector is returned to the proper position, or the requested shift can be completed.  Note: If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  Recommended Vehicle Shift", "(into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Note: Vehicle speeds shown in the preceding chart are for 2H and 4H only.  Vehicle speeds in 4L would be significantly less.  With the vehicle rolling at 1 to 3 mph (2 to 5 km/h), shift an automatic transmission into NEUTRAL (N), or press the clutch pedal on a manual transmission.  While the vehicle is coasting at 1 to 3 mph (2 to 5 km/h), shift the transfer case lever firmly to the desired position.  Do not pause with the transfer case in N (Neutral).  Once the shift is completed, place the automatic transmission into DRIVE or release the clutch pedal on a manual transmission.  To utilize your manual", "into DRIVE or release the clutch pedal on a manual transmission.  To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Manual Transmission Shift Speeds in MPH (KM/H) Engine Speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.6L Accel.  15 (24) 24 (39) 50 (80) 65 (104) 70 (112) Cruise 10 (16) 19 (31) 40 (64) 55 (88) 65 (105) The transmission will automatically downshift as the vehicle slows (to prevent engine lugging) and will display the current gear.  The transmission will automatically downshift to FIRST gear when coming to a stop.  After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or THIRD gear, in 4L range).  Tapping (+) (at a stop) will allow starting in", "FIRST or SECOND gear (or THIRD gear, in 4L range).  Tapping (+) (at a stop) will allow starting in SECOND gear.  Starting out in SECOND or THIRD gear can be helpful in snowy or icy conditions.  If a requested downshift would cause the engine to overspeed, that shift will not occur.  The system will ignore attempts to upshift at too low of a vehicle speed.  Holding the gear selector in the (-) position will downshift the transmission to the lowest gear possible at the current speed.  Transmission shifting will be more noticeable when AutoStick is enabled.  The system may revert to automatic shift mode if a fault or overheat condition is detected.", "NEUTRAL (N) Use this range when the vehicle is standing for prolonged periods with the engine running.  Apply the parking brake and shift the transmission into PARK if you must exit the vehicle.  WARNING: Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.  These are unsafe practices that limit your response to changing traffic or road conditions.  You might lose control of the vehicle and have a collision.  CAUTION: Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle N (Neutral) Neutral \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicleWARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages", "without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  Five-position transfer case \u2014 if equipped the transfer case provides five positions: 2h (two-wheel drive high range) 4h auto (four-wheel drive auto high range) 4h part time (four-wheel drive part time high range) n (neutral) 4l (four-wheel drive low range) for additional information on the appropriate use of each transfer case position, see the following information:.  N (Neutral) Neutral \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicleWARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position", "or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.  See Recreational Towing for further information WARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic", "and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.", "SYNC Button Press the SYNC button on the touchscreen to toggle the Sync feature on/off.  The SYNC indicator illuminates when SYNC is on.  SYNC is used to synchronize the passenger temperature setting with the driver temperature setting.  Changing the passenger temperature setting while in SYNC will automatically exit this feature.  Note: The SYNC button is only available on the touchscreen.  Press the settings button on the touchscreen.  Press the paired phones or audio sources button.  Press to select the particular phone or the particular audio device.  A pop-up menu will appear; press \u201cConnect Phone\u201d.  Press the X to exit out of the Settings screen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing", "is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The MAX A/C button is only available on the touchscreen.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsThe SYNC button is only available on the touchscreen.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the", "for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Press the Phone button.  Press the Dial/Keypad button on the touchscreen.  The Touch-Tone screen will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press \u201cDial/Call\u201d.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM", "Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.", "Safety Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.  WARNING: Improperly inflated tires are dangerous and can cause collisions.  Underinflation increases tire flexing and can result in overheating and tire failure.  Overinflation reduces a tire's ability to cushion shock.  Objects on the road and chuckholes can cause damage that result in tire failure.  Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.  Unequal tire pressures can cause steering problems.  You could lose control of your vehicle.  Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.  Always drive with each tire inflated to the recommended cold tire inflation pressure.  Note: Unequal tire pressures from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure", "from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure from side to side may cause the vehicle to drift left or right.  FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.", "turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  Temperature Grades The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire", "wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.  Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.  For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire", "a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead", "the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was", "which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.", "Connected Services Vehicle Finder FAQs Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic,", "disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob", "to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media", "stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201dWARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an", "related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.", "Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately \"\u21e8air bag warning light\" .  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning", "as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bags to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Placing an object on", "you drive, have an authorized dealer service the air bag system immediately.  Placing an object on the floor under the front passenger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision.  Do not place any objects on the floor under the front passenger seat.  If there is a fault present in the OCS, both the PAD Indicator Light and the Air Bag Warning Light will illuminate to show that the Passenger Advanced Front Air Bag is deactivated.  Should this occur, the Passenger Advanced Front Air Bag will remain deactivated until the fault is cleared.  This indicates that you should take the vehicle to an authorized dealer for service immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light", "Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light will illuminate whenever the ocs is unable to classify the front passenger seat status.  A malfunction in the OCS may affect the operation of the air bag system.  If the air bag warning light does not come on, or stays on after you start the vehicle, or it comes on as you drive, take the vehicle to an authorized dealer for service immediately.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  Redundant Air Bag Warning Light If a fault with the Air Bag Warning Light is detected, which could", "Redundant Air Bag Warning Light If a fault with the Air Bag Warning Light is detected, which could affect the Supplemental Restraint System (SRS), the Redundant Air Bag Warning Light will illuminate on the instrument panel.  The Redundant Air Bag Warning Light will stay on until the fault is cleared.  In addition, a single chime will sound to alert you that the Redundant Air Bag Warning Light has come on and a fault has been detected.  If the Redundant Air Bag Warning Light comes on intermittently or remains on while driving have an authorized dealer service the vehicle immediately.  See \"\u21e8air bag warning light\" for more information regarding the redundant air bag warning light.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.", "The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C),", "allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full", "operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "There are four possible dipstick types: Always maintain the oil level within the crosshatch markings on the dipstick.  Adding 1 qt (1 L) of oil when the reading is at the low end of the dipstick range will raise the oil level to the high end of the range marking.  1 \u2014 Power Distribution Center (Fuses) 6 \u2014 Brake Fluid Reservoir Cap 2 \u2014 Battery 7 \u2014 Engine Air Cleaner Filter 3 \u2014 Engine Oil Dipstick 8 \u2014 Power Steering Fluid Reservoir Cap 4 \u2014 Engine Oil Fill 9 \u2014 Washer Fluid Reservoir Cap 5 \u2014 Engine Coolant Pressure Cap 1 \u2014 Battery 6 \u2014 Power Distribution Center (Fuses) 2 \u2014 Engine Oil Fill 7 \u2014 Power Steering Reservoir Cap 3 \u2014 Coolant Pressure Reservoir Cap 8 \u2014 Engine Oil Dipstick 4 \u2014 Brake Fluid Reservoir Cap 9 \u2014 Engine Air Cleaner Filter 5 \u2014 Washer Fluid Reservoir Cap Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and", "of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  To order a hard copy of your service or diagnostic procedure manuals, visit: www.techauthority.com (us and canada).", "Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety", "any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province,", "including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where", "Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html frequently asked questions about installing child restraints with seat belts what is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child", "anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward-facing child restraint, up to the recommended weight limit of the child restraint.  Can the rear-facing child restraint touch the back of the front passenger seat?  Yes contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.  Can the rear head restraints be removed?  Yes the center head restraint can be removed if it interferes with the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint?  No do not twist the buckle stalk in a seating position with an alr retractor.  Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the", "and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.  Use this simple 5-step test to decide whether the child can use the vehicle\u2019s seat belt alone: Can the child sit all the way back against the back of the vehicle seat?  Do the child\u2019s knees bend comfortably over the front of the vehicle seat while the child is still sitting all the way back?  Does the shoulder belt cross the child\u2019s shoulder between the neck and arm?  Is the lap part of the belt as low as possible, touching the child\u2019s thighs and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to any of these questions was \u201cno,\u201d then the child still needs to use a booster seat in this vehicle.  If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s squirming or slouching can move the belt out of position.  If the shoulder belt contacts the", "squirming or slouching can move the belt out of position.  If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.  WARNING: Never allow a child to put the shoulder belt under an arm or behind their back.  In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.  A child must always wear both the lap and shoulder portions of the seat belt correctly.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.", "is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned", "operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates", "temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine", "for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be", "when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool;", "upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  NORMAL OPERATION \u2014 DIESEL ENGINE Observe the following when the diesel engine is operating: All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater", "the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped)", "during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014", "1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service", "is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors", "a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software,", "into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  All cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Remove the two screws that pass through the bed sheet metal.  Tail Lamp Screws Pull the", "(136 kg).  Remove the two screws that pass through the bed sheet metal.  Tail Lamp Screws Pull the outboard side of the lamp rearward, far enough to unsnap the two receptacles on the outboard side of the lamp housing, from the two plastic snap post retainers in the outer box side panel.  Once removed, locate and rotate the appropriate socket a quarter turn counterclockwise, then remove it from the housing.  Pull the bulb straight from the socket to replace.  To install a new bulb, reverse the procedure above.  With the bag opened completely, fold the fabric divider downward and lay the rear window in the bottom of the bag.  Step One Fold the divider upward, covering the rear window.  Step Two Lay the first quarter panel cover assembly all the way to the right side and the second quarter panel cover assembly on the left side.  Secure both using the two hook-and-loop fastener straps on each side.  The quarter panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step Three 1 \u2014", "panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step Three 1 \u2014 Left Quarter Panel Cover Assembly 2 \u2014 Right Quarter Panel Cover Assembly Close the storage bag and store in a safe location.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the", "boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward", "side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  Press the settings button on the touchscreen.  Press the paired phones or audio sources button.  Press to select the particular phone or the particular audio device.  A pop-up menu will appear; press \u201cConnect Phone\u201d.  Press the X to exit out of the Settings screen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The MAX A/C button is only available on", "you to toggle up or down through the available settings.  The MAX A/C button is only available on the touchscreen.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsThe SYNC button is only available on the touchscreen.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of", "to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Press the Phone button.  Press the Dial/Keypad button on the touchscreen.  The Touch-Tone screen will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press \u201cDial/Call\u201d.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or", "press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the", "To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.", "will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.", "The engine is allowed to crank as long as 25 seconds.  If the engine fails to start during this period, please wait at least two minutes for the starter to cool before repeating start procedure.  If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filters to avoid engine damageInstall a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible", "pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damageThe system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  The transmission must be in PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage", "once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage automatically after 10 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Extended Park Starting Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Note: Extended Park condition occurs when the vehicle has not been started or driven for at least 30 days.  CAUTION: To prevent damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15", "damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeThis remote function requires your vehicle to be equipped with a factory-installed Remote Start system.", "On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the", "seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  Vacation/storage for information on maintaining the climate control system when the vehicle is being stored for an extended period of time, see \"\u21e8storing the vehicle\" .  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the", "the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Press and release this button to turn the Climate Control ON/OFF.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  To Turn Off The Engine Using The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control", "(A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control will turn off, but Stability Control will remain active.  Hold the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and", "Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.", "Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an", "information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system", "personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL", "your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.", "Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  When crossing a ravine, gully, ditch, washout or a large rut, the angled approach is the key to maintaining your vehicle's mobility.  Approach these obstacles at a 45-degree angle and let each tire go through the obstacle independently.  You need to use caution when crossing large obstacles with steep sides.  Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover.  If you get caught in a rut,", "at an angle great enough to put the vehicle at risk of a rollover.  If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires.  Use the removed dirt to fill the rut ahead of the turnout you just created.  You should now be able to drive out following the trench you just created at a 45-degree angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your", "a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with", "When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and", "of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.", "Identifying Whether You Have A Rolling Code Or Non-Rolling Code Device Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  You have 30 seconds in which to initiate rolling code final step 2, after completing rolling code final step 1.  Rolling Code Devices To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices", "if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Note: The \u201cLEARN\u201d or \u201cTRAIN\u201d button is not the button you normally use to operate the device.  Identifying Whether You Have A Rolling Code Or Non-Rolling Code Device Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  Non-rolling Code Devices Most devices manufactured before 1995 will not have a rolling code.  These devices will also not have a \u201cLEARN\u201d or \u201cTRAIN\u201d button.", "If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire", "will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to", "top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to", "so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx", "the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the", "form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited", "This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system", "of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use", "or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling,", "to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of", "of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.", "Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The", "for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated", "store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting", "approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedureWARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel", "in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Fuel System Cautions CAUTION: Follow these guidelines to maintain", "cause serious injury or death.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system", "the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic", "with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system", "is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the", "could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with", "For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press", "Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the", "km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that", "while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to", "Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.", "Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset", "section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main", "WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will", "Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac)", "the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe", "READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND", "function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.  Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and", "to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.", "STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can", "(ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both", "well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Lockout Service Whether the keys are locked in your vehicle or frozen locks are keeping you from getting on your way, help is just a phone call away.  This service is limited to providing access to the vehicle\u2019s seating area.  It does not cover the cost of replacement keys.  VEHICLE MAINTENANCE An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions", "Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  WARNING: You can be badly injured working on or around a motor vehicle.  Only do service work for which you have the knowledge and the proper equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a", "Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of", "are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK", "to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle", "handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.", "The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door opener Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  HomeLink\u00ae replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting, or home security systems.  The HomeLink\u00ae unit is powered by your vehicle\u2019s 12 Volt battery.  The HomeLink\u00ae buttons that are located in the overhead console or sunvisor designate the three different HomeLink\u00ae channels.  To operate HomeLink\u00ae, push and release any of the programmed HomeLink\u00ae buttons.  These buttons will activate the devices they are programmed to with each press of the corresponding HomeLink\u00ae button.  The HomeLink\u00ae indicator light is located above the center button.  Place the ignition in the ON/RUN position.  Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program", "hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program while keeping the HomeLink\u00ae indicator light in view.  Continue to press and hold the HomeLink\u00ae button, while you press and release (cycle) your hand-held transmitter every two seconds until HomeLink\u00ae has successfully accepted the frequency signal.  The indicator light will flash slowly and then rapidly when fully trained.  Watch for the HomeLink\u00ae indicator to change flash rates.  When it changes, it is programmed.  It may take up to 30 seconds or longer in rare cases.  The garage door may open and close while you are programming.  Press and hold the programmed HomeLink\u00ae button and observe the indicator light.  If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink\u00ae button is pressed.  To program the two remaining HomeLink\u00ae buttons, repeat each step for each remaining button.  DO NOT erase the channels.  Programming HomeLink\u00ae To A Garage", "each step for each remaining button.  DO NOT erase the channels.  Programming HomeLink\u00ae To A Garage Door Opener To program any of the HomeLink\u00ae buttons to activate your garage door opener motor, proceed as follows: Place the ignition switch into the ON/RUN position.  Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program, while keeping the HomeLink\u00ae indicator light in view.  Push and hold the HomeLink\u00ae button you want to program while you push and hold the garage door opener transmitter button you are trying to replicate.  Continue to hold both buttons and observe the HomeLink\u00ae indicator light.  The HomeLink\u00ae indicator light will flash slowly and then rapidly.  Once this happens, release both buttons.  Note: All HomeLink\u00ae buttons are programmed using this procedure.  You do not need to erase all channels when programming additional buttons.  Note: Make sure the garage door opener motor is plugged in before moving on to the rolling", "Note: Make sure the garage door opener motor is plugged in before moving on to the rolling code/non-rolling code final steps.  Programming HomeLink\u00ae To A Miscellaneous Device The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door openerBe sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  Note: Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission, which may not be long enough for HomeLink\u00ae to pick up the signal during programming.  Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner.  The procedure may need to be performed multiple times to successfully pair the device to your HomeLink\u00ae buttons.  Before You Begin Programming HomeLink\u00ae For efficient programming and accurate transmission of the radio-frequency signal, it is recommended that a new battery be placed", "accurate transmission of the radio-frequency signal, it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink\u00ae system.  Make sure your hand-held transmitter is programmed to activate the device you are trying to program your HomeLink\u00ae button to.  Ensure that your vehicle is parked outside of the garage before you begin programming.  It is recommended that you erase all the channels of your HomeLink\u00ae before you use it for the first time.  Programming HomeLink\u00ae To A Garage Door Opener To program any of the HomeLink\u00ae buttons to activate your garage door opener motor, proceed as follows: Place the ignition switch into the ON/RUN position.  Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program, while keeping the HomeLink\u00ae indicator light in view.  Push and hold the HomeLink\u00ae button you want to program while you push and hold the garage door opener transmitter button you are", "you want to program while you push and hold the garage door opener transmitter button you are trying to replicate.  Continue to hold both buttons and observe the HomeLink\u00ae indicator light.  The HomeLink\u00ae indicator light will flash slowly and then rapidly.  Once this happens, release both buttons.  Note: All HomeLink\u00ae buttons are programmed using this procedure.  You do not need to erase all channels when programming additional buttons.  Note: Make sure the garage door opener motor is plugged in before moving on to the rolling code/non-rolling code final steps.", "The ignition switch must be in the ACC or ON/RUN position to adjust the power mirrors.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the", "unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP", "is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  START The engine will start.  Note: In case the ignition switch does not change with the push of the START/STOP ignition button, the key fob may have a low or depleted battery.  In this situation, a backup method can be used to operate the ignition switch.  Put the nose side of the key fob (side with the mechanical flip key) against the START/STOP ignition button and push to operate the ignition switch.  CAUTION: Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to", "the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.  WARNING: When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the Keyless Enter \u2018n Go\u2122 Ignition in the ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat buildup may cause serious injury or death.", "inside parked vehicles in hot weather.  Interior heat buildup may cause serious injury or death.  CAUTION: An unlocked vehicle is an invitation for thieves.  Always remove key fob from the vehicle and lock all doors when leaving the vehicle unattended.  Note: When opening the driver's door with the ignition in the ON/RUN (engine not running) position, a chime will sound to remind you to place the ignition in the OFF position.  In addition to the chime, the message will display \u201cIgnition Or Accessory On\u201d in the cluster.  ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push", "once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:", "Removing the soft top removing the soft top \u00b9 use this qr code to access your digital experience.  Fully lower the soft top to the Sunrider\u00ae positionCaution: failure to follow the next steps could result in damage to the soft top or vehicle.  Using the provided #T50 Torx head driver and ratchet, unscrew the two Torx head fasteners on the inside of each top mechanism.  Step two utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle\u2019s sport bar and trim.  Store the soft top in a safe, clean, and dry location.  Remove the door frames.  The rear door frames must be removed before the front door framesUsing the provided #T50 Torx head driver and ratchet, unscrew the six Torx head fasteners on both rear corners and the back of the cab, then remove the belt rail.  Note: folding down the rear seats is recommended to provide easier access to the fasteners.  Step five 1 \u2014 corner fasteners 2 \u2014 rear fasteners.  Lowering the soft top \u00b9 use this qr code to access your digital", "fasteners 2 \u2014 rear fasteners.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Fully lower the soft top to the Sunrider\u00ae positionFailure to follow the next steps could result in damage to the soft top or vehicle.  Using the provided #T50 Torx head driver and ratchet, unscrew the two Torx head fasteners on the inside of each top mechanism.  Step Two Utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle\u2019s sport bar and trim.  Store the soft top in a safe, clean, and dry location.  Remove the door frames.  The rear door frames must be removed before the front door framesUsing the provided #T50 Torx head driver and", "frames must be removed before the front door framesUsing the provided #T50 Torx head driver and ratchet, unscrew the six Torx head fasteners on both rear corners and the back of the cab, then remove the belt rail.  Folding down the rear seats is recommended to provide easier access to the fasteners.  Step Five 1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage", "top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.", "Electronic Sway Bar Disconnect \u2014 If Equipped Your vehicle may be equipped with an electronic disconnecting stabilizer/sway bar.  This system allows greater front suspension travel in off-road situations.  This system is controlled by the SWAY BAR switch located on the instrument panel (to the right of the steering column).  Push the SWAY BAR switch to disconnect or connect the sway bar.  The Sway Bar Indicator Light (located in the instrument cluster) will illuminate when the bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when activation conditions are not met.  The stabilizer/sway bar should remain in on-road mode during normal driving conditions.  To disconnect the stabilizer/sway bar, shift to either 4H or 4L and push the SWAY BAR switch to obtain the off-road position The Sway Bar Indicator Light will flash until the stabilizer/sway bar has been fully disconnected.  To return to on-road mode, push the SWAY BAR switch again.  WARNING: Ensure the", "disconnected.  To return to on-road mode, push the SWAY BAR switch again.  WARNING: Ensure the stabilizer/sway bar is reconnected before driving on hard surfaced roads or at speeds above 18 mph (29 km/h); a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  Under certain circumstances, the front stabilizer/sway bar enhances vehicle stability and assists with vehicle control.  The system monitors vehicle speed and will attempt to reconnect the stabilizer/sway bar at speeds over 18 mph (29 km/h).  This is indicated by a flashing or solid Sway Bar Indicator Light.  Once vehicle speed is reduced below 14 mph (22 km/h), the system will once again attempt to return to off-road mode.  Note: The stabilizer/sway bar may be torque locked due to left and right suspension height differences.  This condition is due to driving surface differences or vehicle loading.  In order for the stabilizer/sway bar to disconnect/reconnect, the right and left halves", "loading.  In order for the stabilizer/sway bar to disconnect/reconnect, the right and left halves of the bar must be aligned.  This alignment may require that the vehicle be driven onto level ground or rocked from side to side.  WARNING: If the stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not attempt to drive the vehicle over 18 mph (29 km/h).  Driving faster than 18 mph (29 km/h) with a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  Sway Bar Fault Warning Light \u2014 If Equipped This light will illuminate when there is a fault in the sway bar disconnect system Sway Bar Indicator Light \u2014 If Equipped This indicator light will illuminate when the front sway bar is disconnected.  Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt", "to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.  When TSC is functioning, the ESC Activation/Malfunction Indicator Light will flash, the engine power may be reduced, and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying.  TSC is disabled when the ESC system is in the \u201cPartial Off\u201d or \u201cFull Off\u201d modes.  Note: TSC cannot stop all trailers from swaying.  Always use caution when towing a trailer and follow the trailer tongue weight recommendations.  See \"\u21e8trailer towing\" for further information.  WARNING: If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway.  Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted", "provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.", "Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.  Opening To open the tailgate,", "close the tailgate, lift upward until both sides latch into place.  Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014", "the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the", "it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.", "The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are", "turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings", "seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The engine must be running for the heated steering wheel to operate.  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or", "is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.", "Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an", "information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system", "personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL", "your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.", "In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L 4H The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only", "at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  4H This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front", "surfaced roads.  4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front wheels.  The four-wheel drive system will be automatically engaged when the vehicle senses a loss of traction.  This range provides additional traction for varying road conditions.", "Under seat storage \u2014 if equipped your vehicle may be equipped with two options for under seat storage: non-locking storage wall under seat locking storage bin locking storage bin if equipped, the locking storage bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor", "Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out", "seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Rear Seat Stadium Position The rear seat bottoms can be folded upward into the Stadium Position to create more storage space on the vehicle\u2019s floor, and to access the under seat storage bins (if equipped).  To fold the seat bottom upward, proceed as follows: Lift upward on each section of the seat bottom.  Lift from beneath seat (left side shown) raise the seat bottom upward into the stadium position.  Stadium Position To return the seat bottom to the normal position, push downward on the raised seat bottom.", "Shifting Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Transmission function is monitored electronically for abnormal conditions.  If a condition is detected that could result in transmission damage, Transmission Limp Home mode is activated.  In this mode, the transmission may operate only in certain gears, or may not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some situations, the transmission may not re-engage if the engine is", "and the engine may stall.  In some situations, the transmission may not re-engage if the engine is turned off and restarted.  The Malfunction Indicator Light (MIL) may be illuminated.  A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary.  It is important to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only manufacturer's specified transmission fluid It is important to maintain the transmission fluid at the correct level using the recommended fluid.  Using a transmission fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is", "the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  Using a lower gear while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  This action will also provide better engine braking.  Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing a heavy trailer), use the AutoStick shift control to select a lower gear Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting", "a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  During cold weather, you may experience increased effort in shifting until the transmission fluid warms up.  This is normal.  Routine fluid and", "effort in shifting until the transmission fluid warms up.  This is normal.  Routine fluid and filter changes are not required.  However, change the fluid and filter if the fluid becomes contaminated (with water, etc.  ), or if the transmission is disassembled for any reason.  FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  Do Not Operate The Engine With Failed Parts All engine failures give some warning before the parts fail.  Be on the alert for changes in", "Parts All engine failures give some warning before the parts fail.  Be on the alert for changes in performance, sounds, and visual evidence that the engine requires service.  Some important clues are: engine misfiring or vibrating severely sudden loss of power unusual engine noises fuel, oil or coolant leaks sudden change, outside the normal operating range, in the engine operating temperature excessive smoke oil pressure drop shifting fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or", "is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.", "Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Important Safety Precautions Please", "the seat belt, which could result in serious injury or death.  Important Safety Precautions Please pay close attention to the information in this section.  It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.  Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: Children 12 years old and under should always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint Never allow children to slide the shoulder belt behind them or under their arm.  You should read the instructions provided with your child restraint to make sure that you are using it", "should read the instructions provided with your child restraint to make sure that you are using it properly.  All occupants should always wear their lap and shoulder belts properly.  The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate.  Do not lean against the door or window.  If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.  If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see \"\u21e8if you need assistance\" for customer service contact information.  WARNING: Never place a rear-facing child restraint in front of an air bag.  A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.  Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing", "Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing child restraint in the rear seat.  If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle.  Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will", "the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Folding The Rear Seats To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently To raise the seatback to the proper position, manually lift the seatback until it locks into place.  To return the head restraint to the proper position, manually lift up until it locks into place.  If interference from the cargo area behind the seat prevents the seatback from fully locking, you will have difficulty returning the seats to their proper position.  Note: Each rear seatback can be locked in an upright position using the vehicle key.  Each seatback must be unlocked to release for", "locked in an upright position using the vehicle key.  Each seatback must be unlocked to release for folding.  Note: The vehicle is equipped with stow clips located on the lower trim, next to the rear seats.  Use these clips to hold the seat belt out of the path of the seatback when it is being folded and raised.  Stow clip location you may experience deformation in the seat cushion from the seat belt buckles if the seats are left folded for an extended period of time.  This is normal.  By simply unfolding the seats to the open position, the seat cushion will return to its normal shape over time.  WARNING: Be certain that the seatback is securely locked into position.  Perform a \u201cpush - pull - push\u201d check to confirm the seat is fully locked.  If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers.  A red indicator on the pull strap will be displayed if the seatback is not securely locked.  An improperly latched seat could cause", "will be displayed if the seatback is not securely locked.  An improperly latched seat could cause serious injury.  Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, adjacent to the anchorage symbols on the seatback.  They are just visible when you lean into the rear seat to install the child restraint.  You will easily feel them if you run your finger along the gap between the seatback and seat cushion.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn", "alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals:", "the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.", "Off-Road Driving Tips  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock", "every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be", "use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also", "under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while", "for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches", "toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed", "in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer", "plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can", "damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage", "continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could", "ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  Pitch & Roll The Pitch & Roll page displays the vehicle\u2019s current pitch (angle up and down) and roll (angle side to side) in degrees.  The Pitch & Roll gauges provide a visualization of the current vehicle angle.  How It Works Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your", "and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.  Vehicle info push and release the up or down arrow button until the vehicle info menu icon is displayed in the instrument cluster display.  Push and release the left or right arrow button to scroll through the information submenus and push and release the ok button to select or reset the resettable submenus.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized", "appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about", "www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone", "In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security", "is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Manual Seat Height Adjustment The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.  Lumbar Support The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  Manual Seat Height Adjustment The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.  Adjustable Upper Shoulder Belt Anchorage In the driver and outboard front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt", "seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck.  Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.  As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position.  After you release the anchorage button, try to move it up or down to make sure that it is locked in position.  Note: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature.  This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release button.  To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position.  WARNING: Wearing your seat belt incorrectly could make your injuries in a collision much worse.  You", "Wearing your seat belt incorrectly could make your injuries in a collision much worse.  You might suffer internal injuries, or you could even slide out of the seat belt.  Follow these instructions to wear your seat belt safely and to keep your passengers safe, too.  Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and not resting on your neck.  The retractor will withdraw any slack in the shoulder belt.  Misadjustment of the seat belt could reduce the effectiveness of the safety belt in a crash.  Always make all seat belt height adjustments when the vehicle is stationary.  The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  In the driver and outboard front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck.  Push or squeeze the", "be adjusted upward or downward to position the seat belt away from your neck.  Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.", "STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can", "(ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both", "well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Lockout Service Whether the keys are locked in your vehicle or frozen locks are keeping you from getting on your way, help is just a phone call away.  This service is limited to providing access to the vehicle\u2019s seating area.  It does not cover the cost of replacement keys.  VEHICLE MAINTENANCE An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions", "Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  WARNING: You can be badly injured working on or around a motor vehicle.  Only do service work for which you have the knowledge and the proper equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will", "system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result", "to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Vacation/storage for information on maintaining the climate control system when the vehicle is being stored for an extended period of time, see \"\u21e8storing the vehicle\" .", "Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio.  This condition may be lessened or eliminated by repositioning the mobile phone within the vehicle.  This condition is not harmful to the radio.  If your radio performance does not satisfactorily improve from repositioning the mobile phone, it is recommended that the volume be turned down or off during mobile phone operation when not using the Uconnect system.  Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors.  Installing some form of aftermarket window tinting that affects radio wave signals.  Lots of snow or ice around the wheels or wheel housings.  Using tire chains on the vehicle.  Using wheels/tires not equipped with TPMS sensors.  The radio unit is acting as the amplifier for audio output from the Auxiliary device.  Therefore, if the volume control on the Auxiliary device is set too low, there will be", "device.  Therefore, if the volume control on the Auxiliary device is set too low, there will be insufficient audio signal for the radio unit to play the music on the device.  Sos call system limitations vehicles sold in mexico do not have sos call system capabilities.  SOS or other emergency line operators in Mexico may not answer or respond to SOS system calls.  If the SOS Call system detects a malfunction, any of the following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d an in-vehicle audio message will state \u201cvehicle device requires service.  Please contact an authorized dealer.\u201d even if the sos call system is fully functional, factors beyond fca us llc\u2019s control may prevent or stop the sos call system operation.  These include, but are not", "fca us llc\u2019s control may prevent or stop the sos call system operation.  These include, but are not limited to, the following factors: the ignition is in the off position the vehicle\u2019s electrical systems are not intact the sos call system software and/or hardware are damaged during a crash the vehicle battery loses power or becomes disconnected during a vehicle crash lte (voice/data) or 4g (data) network and/or global positioning satellite signals are unavailable or obstructed equipment malfunction at the sos operator facility operator error by the sos operator lte (voice/data) or 4g (data) network congestion weather buildings, structures, geographic terrain, or tunnels warning: ignoring the rearview mirror light could mean you will not have sos call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the", "turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber.  Never place anything on or near the vehicle\u2019s LTE (voice/data) or 4G (data) and GPS antennas.  You could prevent LTE (voice/data) or 4G (data) and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable LTE (voice/data) or 4G (data) network connection and a GPS", "placing an emergency call.  An operable LTE (voice/data) or 4G (data) network connection and a GPS signal is required for the SOS Call system to function properly.  Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time", "Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Apple CarPlay\u00ae.  Anywhere using your mobile device and Vehicle Branded App From your computer on the Owner\u2019s Site (not available on all functions) Contacting SiriusXM Guardian\u2122 Customer Care (not available on all functions) Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.", "The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door opener Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  HomeLink\u00ae replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting, or home security systems.  The HomeLink\u00ae unit is powered by your vehicle\u2019s 12 Volt battery.  The HomeLink\u00ae buttons that are located in the overhead console or sunvisor designate the three different HomeLink\u00ae channels.  To operate HomeLink\u00ae, push and release any of the programmed HomeLink\u00ae buttons.  These buttons will activate the devices they are programmed to with each press of the corresponding HomeLink\u00ae button.  The HomeLink\u00ae indicator light is located above the center button.  Place the ignition in the ON/RUN position.  Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program", "hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program while keeping the HomeLink\u00ae indicator light in view.  Continue to press and hold the HomeLink\u00ae button, while you press and release (cycle) your hand-held transmitter every two seconds until HomeLink\u00ae has successfully accepted the frequency signal.  The indicator light will flash slowly and then rapidly when fully trained.  Watch for the HomeLink\u00ae indicator to change flash rates.  When it changes, it is programmed.  It may take up to 30 seconds or longer in rare cases.  The garage door may open and close while you are programming.  Press and hold the programmed HomeLink\u00ae button and observe the indicator light.  If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink\u00ae button is pressed.  To program the two remaining HomeLink\u00ae buttons, repeat each step for each remaining button.  DO NOT erase the channels.  Programming HomeLink\u00ae To A Garage", "each step for each remaining button.  DO NOT erase the channels.  Programming HomeLink\u00ae To A Garage Door Opener To program any of the HomeLink\u00ae buttons to activate your garage door opener motor, proceed as follows: Place the ignition switch into the ON/RUN position.  Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program, while keeping the HomeLink\u00ae indicator light in view.  Push and hold the HomeLink\u00ae button you want to program while you push and hold the garage door opener transmitter button you are trying to replicate.  Continue to hold both buttons and observe the HomeLink\u00ae indicator light.  The HomeLink\u00ae indicator light will flash slowly and then rapidly.  Once this happens, release both buttons.  Note: All HomeLink\u00ae buttons are programmed using this procedure.  You do not need to erase all channels when programming additional buttons.  Note: Make sure the garage door opener motor is plugged in before moving on to the rolling", "Note: Make sure the garage door opener motor is plugged in before moving on to the rolling code/non-rolling code final steps.  Programming HomeLink\u00ae To A Miscellaneous Device The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door opener Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  Note: Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission, which may not be long enough for HomeLink\u00ae to pick up the signal during programming.  Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner.  The procedure may need to be performed multiple times to successfully pair the device to your HomeLink\u00ae buttons.  Identifying Whether You Have A Rolling Code Or Non-Rolling Code Device Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the", "Device Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  Before You Begin Programming HomeLink\u00ae For efficient programming and accurate transmission of the radio-frequency signal, it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink\u00ae system.  Make sure your hand-held transmitter is programmed to activate the device you are trying to program your HomeLink\u00ae button to.  Ensure that your vehicle is parked outside of the garage before you begin programming.  It is recommended that you erase all the channels of your HomeLink\u00ae before you use it for the first time.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too", "gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat,", "the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce", "off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on,", "while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system", "vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.", "Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  The MIL will flash for about 10 seconds and then return to being fully", "service is required.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will", "come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running,", "before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can", "position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because", "vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must", "the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the", "i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.  Methylcyclopentadienyl Manganese Tricarbonyl (MMT) In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasolines to", "In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasolines to increase octane.  Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT.  Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles.  The manufacturer recommends that gasoline without MMT be used in your vehicle.  The MMT content of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gasoline retailer whether the gasoline contains MMT.  MMT is prohibited in Federal law and California reformulated gasoline.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or", "void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause", "may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are", "gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.", "Carbon Monoxide Warnings WARNING: Carbon monoxide (CO) in exhaust gases is deadly.  Follow the precautions below to prevent carbon monoxide poisoning: Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when", "is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Exhaust gases can injure or kill.  They contain carbon monoxide (CO), which is colorless and odorless.  Breathing it can make you unconscious and can eventually poison you.  To avoid breathing (CO), follow these safety tips: Carbon monoxide (CO) in exhaust gases is deadly.  Follow the precautions below to prevent carbon monoxide poisoning: Exhaust gases can injure or kill.  They contain carbon monoxide (CO), which is colorless and odorless.  Breathing it can make you unconscious and can eventually poison you.  To avoid breathing CO see A hot exhaust system can start a fire if you park over materials that can burn, such as grass or leaves, and those items that come into contact with your exhaust system.  Do not park or operate your vehicle in areas where", "come into contact with your exhaust system.  Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.  For further information For further information For further information The VIN is found on the left front corner of the A-pillar, visible from outside of the vehicle through the windshield.  Android\u2122 is a trademark of Google Inc. es posible que este equipo o dispositivo no cause interferencia perjudicial y este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operaci\u00f3n no deseada.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is", "never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.", "Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can", "Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  push the VR button, After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s", "system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  push the VR button, After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform", "commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.", "Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the", "form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background", "for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of", "\u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Setting name description voice response length this setting will change the response length for the voice recognition system.  The \u201cBrief\u201d setting provides a shortened audio description from the system.  The \u201cDetailed\u201d setting provides the full audio description from the system.  Show command list this setting will allow you to turn the command list on or off.  The \u201cAlways\u201d setting will always show the Command List.  The \u201cWith Help\u201d setting will show the Command List and provide a brief description of what the command does.  The \u201cNever\u201d setting will turn the Command List off.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune", "the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.", "Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.", "will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To", "and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.", "There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Prior to off-road usage, the side steps should be removed to prevent damage.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in", "Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Side Step", "assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Side Step Removal \u2014 If Equipped There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener locations (one side) remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side steps should be removed to prevent damage.  Side Step Removal \u2014 If Equipped There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four", "the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener locations (one side) remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side steps should be removed to prevent damage.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been", "or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.", "Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button,", "volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold", "which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Natural Speech Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Natural speech allows the user to speak commands in phrases or complete sentences.  The system filters out certain non-word utterances and sounds such as", "or complete sentences.  The system filters out certain non-word utterances and sounds such as \u201cah\u201d and \u201ceh.\u201d The system handles fill-in words such as \u201cI would like to\u201d.  The system handles multiple inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you want to call?\u201d in the case where a phone call was requested but the specific name was not recognized.  The system utilizes continuous dialog.  When the system requires more information from the user, it will ask a question to which the user can respond without pushing the Voice Command button on the steering wheel.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c", "cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  push the VR button, After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear", "the VR button, After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.", "Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.", "in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly", "accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If You Stall Or Begin To Lose Headway If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: If the engine stalls or you lose headway or cannot make it to the top of a steep", "to lock.  WARNING: If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  If the engine stalls or you lose", "with caution, maintaining your momentum as you climb the hill.  If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail", "if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.", "Adding Diesel Exhaust Fluid The DEF gauge (located on the instrument cluster display) will display the level of DEF remaining in the tankNote: Driving conditions (altitude, vehicle speed, load, etc.)  will affect the amount of DEF that is used in your vehicle.  System Overview This vehicle is equipped with a Diesel Exhaust Fluid (DEF) injection system and a Selective Catalytic Reduction (SCR) catalyst to meet the emission requirements.  The def injection system consists of the following components: def tank def pump def injector electronically-heated def lines nox sensors temperature sensors scr catalyst the def injection system and scr catalyst enable the achievement of diesel emissions requirements; while maintaining outstanding fuel economy, drivability, torque and power ratings.  For system messages and warnings see Note: Your vehicle is equipped with a DEF injection system.  You may occasionally hear an audible clicking noise from under the vehicle at a stop.  This is normal operation.  The DEF pump", "audible clicking noise from under the vehicle at a stop.  This is normal operation.  The DEF pump will run for a period of time after engine shutdown to purge the DEF system.  This is normal operation and may be audible from the rear of the vehicle.  DEF Fill Procedure Remove cap from DEF fill inlet (located in fuel door).  Fuel and diesel exhaust fluid fill location 1 \u2014 diesel fuel filler 2 \u2014 diesel exhaust fluid filler insert def fill adapter/nozzle into def fill inlet.  Note: the def gauge may take up to five seconds to update after adding a gallon or more of diesel exhaust fluid (def) to the def tank.  If you have a fault related to the DEF system, the gauge may not update to the new level.  See an authorized dealer for service.  The DEF gauge may also not immediately update after a refill if the temperature of the DEF fluid is below 12\u00b0F (-11\u00b0C).  The DEF line heater will possibly warm up the DEF fluid and allow the gauge to update after a period of run time.  Under very cold conditions, it is possible", "allow the gauge to update after a period of run time.  Under very cold conditions, it is possible that the gauge may not reflect the new fill level for several drives.  Excessive overfilling of the DEF tank can result in a MIL lamp/fault code and inaccurate level readings.  Refilling with nozzles you can fill up at any def distributor.  Proceed as follows: insert the def nozzle in the filler, start refilling and stop refilling at the first shut-off (the shut-off indicates that the def tank is full).  Do not proceed with the refilling, to prevent spillage of DEF.  Extract the nozzle.  Refilling with containers proceed as follows: check the expiration date.  Read the advice for use on the label before pouring the content of the bottle into the DEF tank.  If systems which cannot be screwed in (e.g.  Tanks) are used for refilling, after the indication appears on the instrument panel display \"\u21e8instrument cluster display\" fill the def tank with no more than 2 gal (8 l).  If containers which can be screwed to the", "fill the def tank with no more than 2 gal (8 l).  If containers which can be screwed to the filler are used, the reservoir is full when the DEF level in the container stops pouring out.  Do not proceed further.  Caution: to avoid def spillage, and possible damage to the def tank from overfilling, do not \u201ctop off\u201d the def tank after filling.  DO NOT OVERFILL.  DEF will freeze below 12\u00baF (-11\u00baC).  The DEF system is designed to work in temperatures below the DEF freezing point, however, if the tank is overfilled and freezes, the system could be damaged.  When DEF is spilled, clean the area immediately with water and use an absorbent material to soak up the spills on the ground.  Do not attempt to start your engine if DEF is accidentally added to the diesel fuel tank as it can result in severe damage to your engine, including but not limited to failure of the fuel pump and injectors.  Never add anything other than DEF to the tank \u2013 especially any form of hydrocarbon such as diesel fuel, fuel system additives,", "DEF to the tank \u2013 especially any form of hydrocarbon such as diesel fuel, fuel system additives, gasoline, or any other petroleum-based product.  Even a very small amount of these, less than 100 parts per million or less than 1 oz.  per 78 gal (295 L) will contaminate the entire DEF system and will require replacement.  If owners use a container, funnel or nozzle when refilling the tank, it should either be new or one that has only been used for adding DEF.  Mopar\u00ae provides an attachable nozzle with its DEF for this purpose.  Stop filling the DEF tank immediately when any of the following happen: DEF stops flowing from the fill bottle into the DEF fill inlet, DEF splashes out the fill inlet, or a DEF pump nozzle automatically shuts off.  Reinstall cap onto DEF fill inlet.  Note: For the correct DEF fluid type see Adding Diesel Exhaust Fluid The DEF gauge (located on the instrument cluster display) will display the level of DEF remaining in the tank Note: Driving conditions (altitude, vehicle speed, load,", "the level of DEF remaining in the tank Note: Driving conditions (altitude, vehicle speed, load, etc.)  will affect the amount of DEF that is used in your vehicle.  Diesel Exhaust Fluid Diesel Exhaust Fluid (DEF) sometimes known simply by the name of its active component, UREA, is a key component of Selective Catalytic Reduction (SCR) systems, which help diesel vehicles meet stringent emission regulations.  DEF is a liquid reducing agent that reacts with engine exhaust in the presence of a catalyst to convert smog-forming Nitrogen Oxides (NOx) into harmless nitrogen and water vapor.  For further information", "REFUELING IN EMERGENCY \u2013 IF EQUIPPED The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Note: In certain cold conditions, ice may prevent the fuel door from opening.  If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button.  Do not pry on the door.  See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you", "flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine", "will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24", "by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  If Engine Fails To Start If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  WARNING: Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.", "flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly CAUTION: To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  Normal Starting Observe the instrument cluster lights when starting the engine.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  Note: a delay of the start of up to", "brake pedal while pushing the ENGINE START/STOP button once.  Note: a delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  Caution: if the water in fuel indicator light remains on, do not start the engine before you drain the water from the fuel filters to avoid engine damage.  The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Note: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF", "pumping or pressing the accelerator pedal.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load", "OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Stopping The Engine After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Note: Refer to the following chart for proper engine shutdown.  Note: Under certain conditions the Stop/Start system may be temporarily disabled and the engine fan will run after the engine is turned off to protect the engine.  These conditions are under high load and high temperature conditions.", "On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the", "seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not", "shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Press and release this button to turn the Climate Control ON/OFF.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  To Turn Off The Engine Using The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control will turn off, but Stability Control will remain active.  Hold the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC", "the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to", "turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  A/C Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Note: For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.", "Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle", "X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the", "the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is", "will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF", "touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.", "Setting Name Description Language This setting will change the language of the Uconnect system and Instrument Cluster Display.  The available languages are \u201cEnglish\u201d, \u201cFran\u00e7ais\u201d, and \u201cEspa\u00f1ol\u201d.  Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Press the Media button on the touchscreen to begin.  Change the source to \u201cBluetooth\u00ae\u201d.  Press the Bluetooth\u00ae button on the touchscreen to display the Paired Audio Devices screen.  Press the Add Device button on the touchscreen.  If there is no device currently connected with the system, a pop-up will appear.  Search for available devices on your Bluetooth\u00ae-enabled audio device.  When prompted on the device, confirm the PIN shown on the Uconnect screen.  Uconnect Phone will display an in-process screen while the system is connecting.  When the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite device.  Selecting \u201cYes\u201d will make this device the highest priority.", "or not this is your favorite device.  Selecting \u201cYes\u201d will make this device the highest priority.  This device will take precedence over other paired devices within range.  Uconnect Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  Setting name description language this setting will change the language of the uconnect system and instrument cluster display.  The available languages are \u201cEnglish\u201d, \u201cFran\u00e7ais\u201d, and \u201cEspa\u00f1ol\u201d.  Natural Speech Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Natural speech allows the user to speak commands in phrases or complete sentences.  The system filters out certain non-word utterances and sounds such as \u201cah\u201d and \u201ceh.\u201d The system handles fill-in words such as \u201cI would like to\u201d.  The system handles multiple inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For", "inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you want to call?\u201d in the case where a phone call was requested but the specific name was not recognized.  The system utilizes continuous dialog.  When the system requires more information from the user, it will ask a question to which the user can respond without pushing the Voice Command button on the steering wheel.  When the Language button is pressed on the touchscreen, the system displays the different language options.  Once an option is selected, the system will display in the chosen language.  The available setting is: note: depending on the vehicle\u2019s options, feature settings may vary.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu", "press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.", "Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect", "against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.", "vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code", "leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants", "are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the", "the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric topDo not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  If the temperature is below", "installation can cause water to leak into the vehicle's interior.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on", "of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle", "the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "Adaptive Cruise Control (ACC) Ready Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.  Monitoring battery level status led light red 40% or lower yellow 40% to 70% green 70% to 100% electronic stability control (esc) active warning light \u2014 if equipped this warning light will indicate when the electronic stability control system is active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and", "30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.  Adaptive Cruise Control (ACC) Set Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.  Adaptive Cruise Control (ACC) Ready Indicator Light", "control has been turned on, but not set.  Adaptive Cruise Control (ACC) Ready Indicator Light \u2014 If Equipped With a Premium Instrument Cluster This light will turn on when the vehicle equipped with Adaptive Cruise Control (ACC) has been turned on, but not set.", "Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be", "these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the", "upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside),", "Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.", "or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels", "top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the", "first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five", "up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.", "Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C.These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  For the recommended", "acceleration, cornering, hydroplaning, or peak traction characteristics.  For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet", "highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests,", "wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.", "Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle.  These kinds of hitches are commonly used to tow small and medium sized trailers.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle", "Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the", "used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  When using a fascia/bumper mounted ball on any model, the trailer weight is limited to 3,500 lb (1,588 kg), 30 ft 2 (2.79 m 2 ) frontal area, and 350 lb (159 kg) tongue weight.  The trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie.  the GVWR), and the", "must be considered as part of the combined weight of occupants and cargo (ie.  the GVWR), and the GVWR should never exceed the weight referenced on the Tire And Loading Information Placard", "The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring Height (H) Attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the", "approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  Service Forward Collision Warning (FCW) Light \u2014 If Equipped This warning light will illuminate to indicate a fault in the Forward Collision Warning System.", "This warning light will illuminate to indicate a fault in the Forward Collision Warning System.  Contact an authorized dealer for service Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.", "System Overview This vehicle is equipped with a Diesel Exhaust Fluid (DEF) injection system and a Selective Catalytic Reduction (SCR) catalyst to meet the emission requirements.  The def injection system consists of the following components: def tank def pump def injector electronically-heated def lines nox sensors temperature sensors scr catalyst the def injection system and scr catalyst enable the achievement of diesel emissions requirements; while maintaining outstanding fuel economy, drivability, torque and power ratings.  For system messages and warnings see Note: Your vehicle is equipped with a DEF injection system.  You may occasionally hear an audible clicking noise from under the vehicle at a stop.  This is normal operation.  The DEF pump will run for a period of time after engine shutdown to purge the DEF system.  This is normal operation and may be audible from the rear of the vehicle.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control", "localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  Trailer Sway Control (TSC) TSC", "standards required by the Environmental Protection Agency.  Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.  When TSC is functioning, the ESC Activation/Malfunction Indicator Light will flash, the engine power may be reduced, and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying.  TSC is disabled when the ESC system is in the \u201cPartial Off\u201d or \u201cFull Off\u201d modes.  Note: TSC cannot stop all trailers from swaying.  Always use caution when towing a trailer and follow the trailer tongue weight recommendations.  See \"\u21e8trailer towing\" for further information.  WARNING: If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway.", "Connected Services Roadside Assistance FAQs What is the phone number for roadside assistance call?  The phone number is: us: 1-800-521-2779 canada: 1-800-363-4869 if i am subscribed to siriusxm guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance.  No, however your new vehicle may include Roadside Assistance Call services.  What to Do If your vehicle requires jump start assistance, out of gas/fuel delivery, tire service, lockout service or towing as a result of a mechanical breakdown, dial toll-free: USA: 1-800-521-2779/Canada: 1-800-363-4869.  Provide your name, Vehicle Identification Number (VIN) required for covered services, license plate number, and your location, including the telephone number from which you are calling.  Briefly describe the nature of the problem and answer a few simple questions.  You will be given the name of the service provider and an estimated time of arrival.  If you feel you are in an unsafe situation, please let us know.  With your consent,", "of arrival.  If you feel you are in an unsafe situation, please let us know.  With your consent, we will contact local police or safety authorities.  Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  What is the phone number for roadside assistance call?  The phone number is: US: 1-800-521-2779 Canada: 1-800-363-4869 If I am subscribed to SiriusXM Guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance?  No, however your new vehicle may include Roadside Assistance Call services.  FCA US LLC reserves the right to modify the terms or discontinue the Roadside Assistance Program at any time.  The Roadside Assistance", "the terms or discontinue the Roadside Assistance Program at any time.  The Roadside Assistance program is subject to restrictions and conditions of use, which are determined solely by FCA US LLC.  If Unable to Contact Roadside Assistance", "In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  EMISSIONS INSPECTION", "diesel emissions standards required by the Environmental Protection Agency.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or", "ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently", "is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button", "and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an", "Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a", "to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate", "OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.", "Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A", "vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all", "system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not", "you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON", "engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.", "Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry (If Equipped) The Passive Entry system is a feature that allows you to lock and unlock the vehicle\u2019s door(s) and tailgate without having to push the key fob lock or unlock buttons.  Note: Passive Entry may be programmed on/off through Uconnect Settings The key fob may not be detected by the vehicle Passive Entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may interfere with the key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.  Passive Entry Unlock initiates Headlight Illumination On Approach (low beams, license plate lamp, parking lights) for whichever duration is set within the Uconnect Settings between 0, 30, 60 or 90 seconds.  Passive Entry Unlock also initiates two flashes of the turn signal lights.  If wearing gloves, if it has been raining/snowing, or there is salt/dirt covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a", "covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.  The doors may unlock when water is sprayed on the Passive Entry door handles if the key fob is located outside of the vehicle within 5 ft (1.5 m) of the handle.  If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will relock and, if equipped, will arm the Vehicle Security system.  Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry (If Equipped) The Passive Entry system is a feature that allows you to lock and unlock the vehicle\u2019s door(s) and tailgate without having to push the key fob lock or unlock buttons.  Note: Passive Entry may be programmed on/off through Uconnect Settings The key fob may not be detected by the vehicle Passive Entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may interfere with the key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.", "key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.  Passive Entry Unlock initiates Headlight Illumination On Approach (low beams, license plate lamp, parking lights) for whichever duration is set within the Uconnect Settings between 0, 30, 60 or 90 seconds.  Passive Entry Unlock also initiates two flashes of the turn signal lights.  If wearing gloves, if it has been raining/snowing, or there is salt/dirt covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.  The doors may unlock when water is sprayed on the Passive Entry door handles if the key fob is located outside of the vehicle within 5 ft (1.5 m) of the handle.  If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will relock and, if equipped, will arm the Vehicle Security system.  Frequency Operated Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive", "Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.  FOBIK-Safe only executes in vehicles with Passive Entry.  There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made by a valid Passive Entry key fob while a door is open.  A lock request is made by the Passive Entry door handle while a door is open.  A lock request is made by the door panel switch while the door is open.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  Note: The", "system, the key fob protection described in this section remains active/functional.  Note: The vehicle will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle.  The vehicle will not unlock the doors when any of the following conditions are true: A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are manually locked using the door lock knobs.  Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.  To Lock The Vehicle\u2019s Doors With one of the vehicle\u2019s Passive Entry key fobs within 5 ft (1.5 m) of the driver or passenger front door handles, pushing the Passive Entry lock button will lock the vehicle doors.  Note: When pushing the door handle lock button, DO NOT grab the door handle.  This could unlock the door(s).  Note: After pushing the door handle button, the driver must wait three seconds before locking or", "Note: After pushing the door handle button, the driver must wait three seconds before locking or unlocking the doors, using any Passive Entry door handle.  This is done to allow the driver to check if the vehicle is locked by pulling the door handle without the vehicle unlocking.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in \u201cPreventing Inadvertent Locking Of Passive Entry Key Fob In Vehicle\u201d remains active/functional.  The Passive Entry system will not operate if the key fob battery is depleted  Frequency Operated Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.  FOBIK-Safe only executes in vehicles with Passive Entry.  There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made", "situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made by a valid Passive Entry key fob while a door is open.  A lock request is made by the Passive Entry door handle while a door is open.  A lock request is made by the door panel switch while the door is open.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  Note: The vehicle will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle.  The vehicle will not unlock the doors when any of the following conditions are true: A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are", "outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are manually locked using the door lock knobs.  Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.", "brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the", "to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second", "to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  Interior Courtesy Lights When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right)", "the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  To enter the \u201cPartial Off\u201d mode, momentarily push the ESC OFF button and the ESC OFF Indicator Light will illuminate.  To turn the ESC on again, momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door", "momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Automatic Headlight System will turn the headlights on or off according to ambient light levels.  To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation.  When the system is on, the headlight time delay feature is also on.  This means the headlights will stay on for up to 90 seconds (programmable through the uconnect settings \"\u21e8uconnect settings\" ) after you place the ignition into the off position.  To turn the automatic system off, move the headlight switch out of the AUTO position.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the", "The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Reduce power to unnecessary loads if possible: Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed", "settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s exterior and interior lights.  When the \u201cDaytime Running Lights\u201d feature is selected, the daytime running lights can be turned on or off.  This feature is only allowed by law in the country of the vehicle purchase.  Depending on the vehicle\u2019s options, feature settings may vary.  Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to", "lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other", "systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "Cooling System WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or", "has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is", "the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Place Hand In Hood Opening  Cooling System WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can", "fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Halogen Headlamps \u2014 If Equipped See the following steps to replace: Open hood and support using prop rod.  Remove the front grille.  Turn the retainers along the top a quarter turn counterclockwise and remove.  Pull the bottom of the grille away, starting at one side and working toward the other.  Remove the three screws holding the headlamp to the vehicle.  Remove lamp from the vehicle.  Remove the lamp from the collar.  Grab the bulb and turn a quarter turn counterclockwise.  Pull the bulb from the housing.  Push connector locking tab to the unlock position.  Remove connector from bulb.  Push connector onto new bulb base, and push the connector locking tab to the lock position.  Reinstall bulb housing.  Rotate the bulb a quarter turn clockwise.  CAUTION: Do not touch the new bulb with your fingers.  Oil contamination will severely shorten bulb life.  If", "not touch the new bulb with your fingers.  Oil contamination will severely shorten bulb life.  If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.  Note: We recommend seeing an authorized dealer for service.  Opening The Hood Release both of the outside hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Note: Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.", "Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to", "of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances", "(if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle", "repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Frequency Operated Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your", "To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.  FOBIK-Safe only executes in vehicles with Passive Entry.  There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made by a valid Passive Entry key fob while a door is open.  A lock request is made by the Passive Entry door handle while a door is open.  A lock request is made by the door panel switch while the door is open.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  Note: The vehicle will only unlock the doors", "described in this section remains active/functional.  Note: The vehicle will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle.  The vehicle will not unlock the doors when any of the following conditions are true: A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are manually locked using the door lock knobs.  Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.", "Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is", "turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Lightly push the multifunction lever up or down, without moving beyond the detent, and the turn signal will flash three times then automatically turn off.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.", "Fastener Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  To remove the Fastener Bin: Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Note: The soft top fasteners do not go in the Fastener Bin.  Rear Wall Storage Bin Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  Fastener Bin Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  The Locking Storage Bin can be removed by unfastening the four", "the bottom of the Fastener Bin.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  To remove the Fastener Bin: Remove the lid and foam inserts from the Fastener Bin.  Remove the three nuts from the bottom of the Fastener Bin.  Your vehicle is equipped with a Fastener Bin used to store the fasteners for the doors, windshield, and hard top (if equipped) while not in use.  The Fastener Bin is located behind the rear seat storage bin.  The Fastener Bin contains foam inserts for each of the fasteners; they are removable.  Remove the grommets under the front seat (one left and one right).  Carpet Split Then pull the carpet out, to the rear and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin", "and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin (if equipped), by removing the four bolts that hold it to the floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then lift the assembly out from under the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear Retainers Remove carpet from the vehicle.  When reinstalling the carpet, perform these steps in reverse order making sure that the carpet is tucked under the scuffs, B-pillar, console, and then refasten the grommets.  Inside the bin are three removable dividers to set up storage that works best for you.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  The rear wall netting can be accessed the same way as the rear wall storage", "the floor are removed.  The rear wall netting can be accessed the same way as the rear wall storage bin.  If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.", "Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This", "does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard", "hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine", "service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as", "your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Synthetic Engine Oils Your engine was designed for synthetic engine oils, only use synthetic API approved engine oils.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The", "(API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.", "Adaptive Cruise Control (ACC) Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC ACC will allow you to keep Cruise Control engaged in light to moderate traffic conditions without the constant need to reset your speed.  ACC utilizes a radar sensor and a forward-facing camera designed to detect a vehicle directly ahead of you to maintain a set speed.  Note: If the ACC sensor detects a vehicle ahead, ACC will apply limited braking or accelerate (not to exceed the original set speed) automatically to maintain a preset following distance, while matching the speed of the vehicle ahead.  Any chassis/suspension or tire size modifications to the vehicle will affect the performance of the Adaptive Cruise Control and Forward Collision Warning system.  Fixed Speed", "the performance of the Adaptive Cruise Control and Forward Collision Warning system.  Fixed Speed Cruise Control (ACC not enabled) will not detect vehicles directly ahead of you.  Always be aware of the feature selected WARNING: Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The acc system: does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be", "a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  You should turn the ACC system off and do not use: When driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.e., in highway construction zones).  When entering a turn lane or highway off-ramp; when driving on roads that are winding, icy, snow-covered, slippery, or have steep uphill or downhill slopes.  When towing a trailer up or down steep slopes.  When circumstances do not allow safe driving at a constant speed.  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.", "use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system:  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The", "major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.", "Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the", "windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the", "EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present", "will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a", "engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  When Remote Start is active, and the outside ambient temperature is 40\u00b0F (4.5\u00b0C) or below, the system will automatically activate front defrost for 15 minutes or less.  The time is dependent on the ambient temperature.  Once the timer expires, the system will automatically adjust the", "on the ambient temperature.  Once the timer expires, the system will automatically adjust the settings depending on ambient conditions.  See \u201cRemote Start Comfort Systems \u2014 If Equipped\u201d in the next section for detailed operation.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  These features will stay on through the duration of Remote Start, or until the ignition", "button.  These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.  To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations", "is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining", "uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.", "the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.", "Windshield Washers To use the washer, pull the lever toward you and hold until desired spray is reached.  If the lever is pulled while in the delay range, the wiper will start and continue to operate for two or three wipe cycles after the lever is released.  Then, the intermittent interval previously selected will resume.  If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles.  Then, the wipers will turn off.  Note: As a protective measure, the washer will stop if the switch is held for more than 20 seconds.  Once the switch is released the washer will resume normal operation.  WARNING: Sudden loss of visibility through the windshield could lead to a collision.  You might not see other vehicles or other obstacles.  To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a", "Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  Mist Push upward on the wiper", "damage to the wiper motor may occur when the vehicle is restarted.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.", "Rim Size This is the rim size that is appropriate for the tire size listed.  Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with", "= rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire.  This is the rim size that is", "the maximum permissible cold tire inflation pressure for this tire.  This is the rim size that is appropriate for the tire size listed.  P (Passenger) \u2014 Metric tire sizing is based on US design standards.  P-Metric tires have the letter \u201cP\u201d molded into the sidewall preceding the size designation.  Example: P215/65R15 95H.  European \u2014 Metric tire sizing is based on European design standards.  Tires designed to this standard have the tire size molded into the sidewall beginning with the section width.  The letter \u201cP\u201d is absent from this tire size designation.  Example: 215/65R15 96H.  LT (Light Truck) \u2014 Metric tire sizing is based on US design standards.  The size designation for LT-Metric tires is the same as for P-Metric tires except for the letters \u201cLT\u201d that are molded into the sidewall preceding the size designation.  Example: LT235/85R16.  Temporary spare tires are designed for temporary emergency use only.  Temporary high pressure compact spare tires have the letter \u201cT\u201d or \u201cS\u201d molded into the sidewall", "Temporary high pressure compact spare tires have the letter \u201cT\u201d or \u201cS\u201d molded into the sidewall preceding the size designation.  Example: T145/80D18 103M.  High flotation tire sizing is based on US design standards and it begins with the tire diameter molded into the sidewall.  Example: 31x10.5 R15 LT. The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in", "tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl", "load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire full size spare \u2014 if equipped the full size spare is for temporary emergency use only.  This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not.  This spare tire may have limited tread life.  When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced.  Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity.", "Adding Washer Fluid The fluid reservoir is located in the engine compartment.  Be sure to check the fluid level at regular intervals.  Fill the reservoir with windshield washer solvent only (not radiator antifreeze).  When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades; this will help blade performance.  To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate.  This rating information can be found on most washer fluid containers.  WARNING: Commercial windshield washer solvents are flammable.  They could ignite and burn you.  Care must be exercised when filling or working around the washer solution.  1 \u2014 Power Distribution Center (Fuses) 6 \u2014 Brake Fluid Reservoir Cap 2 \u2014 Battery 7 \u2014 Engine Air Cleaner Filter 3 \u2014 Engine Oil Dipstick 8 \u2014 Power Steering Fluid Reservoir Cap 4 \u2014 Engine Oil Fill 9 \u2014 Washer Fluid Reservoir Cap 5 \u2014", "8 \u2014 Power Steering Fluid Reservoir Cap 4 \u2014 Engine Oil Fill 9 \u2014 Washer Fluid Reservoir Cap 5 \u2014 Engine Coolant Pressure Cap 1 \u2014 Battery 6 \u2014 Power Distribution Center (Fuses) 2 \u2014 Engine Oil Fill 7 \u2014 Power Steering Reservoir Cap 3 \u2014 Coolant Pressure Reservoir Cap 8 \u2014 Engine Oil Dipstick 4 \u2014 Brake Fluid Reservoir Cap 9 \u2014 Engine Air Cleaner Filter 5 \u2014 Washer Fluid Reservoir Cap Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Fluid Level Check Check the fluid level by removing the fill plug.  The fluid level should be between the bottom of the fill hole and a point not more than 3/16 of an inch (4.76 mm) below the bottom of the hole.  Add fluid, if necessary, to maintain the proper level.  Fluid Level Check The fluid level should be", "Add fluid, if necessary, to maintain the proper level.  Fluid Level Check The fluid level should be to the bottom edge of the fill hole when the vehicle is in a level position.  Fluid Level Check \u2014 Brake Master Cylinder The fluid level of the master cylinder should be checked whenever the vehicle is serviced, or immediately if the Brake System Warning Light is on.  If necessary, add fluid to bring level within the designated marks on the side of the reservoir of the brake master cylinder.  Be sure to clean the top of the master cylinder area before removing cap.  With disc brakes, fluid level can be expected to fall as the brake pads wear.  Brake fluid level should be checked when pads are replaced.  If the brake fluid is abnormally low, check the system for leaks.  For further information WARNING: Use only manufacturer recommended brake fluid Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance.  The proper type of brake fluid for your vehicle is also", "system and/or impair its performance.  The proper type of brake fluid for your vehicle is also identified on the original factory installed hydraulic master cylinder reservoir.  To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container.  Keep the master cylinder reservoir cap secured at all times.  Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point.  This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure.  This could result in a collision.  Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire.  Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces.  Do not allow petroleum based fluid to contaminate the brake fluid.  Brake seal components could be damaged, causing partial or complete brake failure.", "brake fluid.  Brake seal components could be damaged, causing partial or complete brake failure.  This could result in a collision.", "Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be", "these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the", "upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside),", "Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.", "or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels", "top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Remove both front panels Open both front doors.  Using the provided #50 Torx head driver and ratchet, remove the two Torx head", "both front doors.  Using the provided #50 Torx head driver and ratchet, remove the two Torx head screws that secure the hard top at the B-pillar (near the top of the front doors).  Step Three If equipped, remove the lower interior soft trim panel (attached by the hook-and-loop fastener) by pulling the panel away from the trim.  Step Four Remove the Torx head fasteners that secure the hard top to the vehicle: two along the interior body side, rearward of the back doors, followed by the four fasteners along the back of the vehicle cab using the #T50 Torx head driver.  Step Five 1 \u2014 Vehicle Cab Torx Head Fasteners 2 \u2014 Body side Torx Head Fasteners Locate the wire harness on the left rear inside corner of the vehicle.  To access the harness, remove the plastic cover by pushing the cover to the side, and sliding it off.  Do not force open; this will break the plastic cover.  Step Six To release the wire harness, pull back on the red latch (1), then push down on the black button (2) while pulling the harness out.", "back on the red latch (1), then push down on the black button (2) while pulling the harness out.  Step Seven 1 \u2014 Red Latch 2 \u2014 Black Button Remove the hard top from the vehicle.  Install the provided edge protectors along the bottom edges of the hard top, and place the hard top on a soft surface to prevent damage.  The removal of the Hard Top requires four adults located on each corner.  Failure to follow this caution could damage the Hard Top.  Store the wire harness by removing the storage cover on the quarter trim.  Use the mechanical key blade to pry the cover open.  Step Nine Tuck the wire harness inside the storage compartment, and replace the cover.", "If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you", "prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides", "a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is", "may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  FOLDING WINDSHIELD The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element provides.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving", "the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  WARNING: Carefully follow these warnings to help protect against personal injury: Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these", "fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "Disposal Of Used Coolant Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh", "in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  ENGINE FLUIDS AND LUBRICANTS CAUTION: Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic", "coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Note: If the vehicle is exposed to extreme cold", "engine coolant (antifreeze) is not recommended.  Note: If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Used ethylene glycol-based coolant (antifreeze) OAT or HOAT, is a regulated substance requiring proper disposal.  Check with your local authorities to determine the disposal rules for your community.  To prevent ingestion by animals or children, do not store ethylene glycol-based coolant in open containers or allow it to remain in puddles on the ground, clean up any ground spills immediately.  If ingested, seek emergency assistance immediately.  It is the owner's responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.", "freezing according to the temperatures occurring in the area where the vehicle is operated.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system, please contact an authorized dealer.  Mixing engine coolant types is not recommended and can result in cooling system damage.  If HOAT and OAT coolant are mixed in an emergency, have an authorized dealer drain, flush, and refill with OAT coolant (conforming to MS.90032) as soon as possible.  Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system", "a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.  Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease", "Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.  Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any \u201cglobally compatible\u201d coolant (antifreeze).  If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant (antifreeze) products.  Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze).  Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Please review these", "Use of propylene glycol-based engine coolant (antifreeze) is not recommended.  Please review these recommendations for using Organic Additive Technology (OAT) engine coolant that meets the requirements of the manufacturer Material Standard MS.90032.  When adding engine coolant (antifreeze): The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  The tongue weight of the trailer The weight of any other type of cargo or equipment put in or on your vehicle The weight of the driver and all passengers For further information on GAWRs, vehicle loading, and trailer towing, see If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OAT coolant (conforming to MS.90032).  It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the Run Flat mode.  Selection Of Coolant For further information Note: Mixing of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine", "of engine coolant (antifreeze), other than specified Organic Additive Technology (OAT) engine coolant, may result in engine damage and may decrease corrosion protection.  OAT engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant or any \u201cglobally compatible\u201d coolant.  If a non-OAT engine coolant is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible.  Do not use water alone or alcohol-based engine coolant products.  Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator engine coolant and may clog the radiator.  This vehicle has not been designed for use with propylene glycol-based engine coolant.  Use of propylene glycol-based engine coolant is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill", "is not recommended.  Some vehicles require special tools to add coolant properly.  Failure to fill these systems properly could lead to severe internal engine damage.  If any coolant is needed to be added to the system please contact an authorized dealer.", "See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you", "See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.", "will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Jack Location The jack and tools are stored under the right rear seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools", "seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat.  Removing the wing bolt release the tool bag straps from the jack and remove tools from bag.  Jack and tool bag remove tool kit and assemble tools.  Jack And Tool Bag There are two ways to assemble the tools: Note: If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  CAUTION: The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools, always reinstall them in the original carrier and location.  While", "After using the jack and tools, always reinstall them in the original carrier and location.  While driving you may experience abrupt stopping, rapid acceleration or sharp turns.  A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.", "ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are", "in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the", "starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to", "ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or", "it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.", "Connected Services Roadside Assistance FAQs What is the phone number for roadside assistance call?  The phone number is: us: 1-800-521-2779 canada: 1-800-363-4869 if i am subscribed to siriusxm guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance.  No, however your new vehicle may include Roadside Assistance Call services.  What to Do If your vehicle requires jump start assistance, out of gas/fuel delivery, tire service, lockout service or towing as a result of a mechanical breakdown, dial toll-free: USA: 1-800-521-2779/Canada: 1-800-363-4869.  Provide your name, Vehicle Identification Number (VIN) required for covered services, license plate number, and your location, including the telephone number from which you are calling.  Briefly describe the nature of the problem and answer a few simple questions.  You will be given the name of the service provider and an estimated time of arrival.  If you feel you are in an unsafe situation, please let us know.  With your consent,", "of arrival.  If you feel you are in an unsafe situation, please let us know.  With your consent, we will contact local police or safety authorities.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.", "Replacing The Battery In The Key Fob The recommended replacement battery is CR2450.  Remove the back cover of the key fob by inserting a flat-blade screwdriver into the slot on the bottom of the fob.  Apply light pressure until the cover unsnaps being careful not to damage the seal.  Proceed counterclockwise (in the order shown in the following image) to loosen the remaining snaps until the battery cover can be removed.  1-3 \u2013 back cover pry points remove the depleted battery by inserting a small flat-blade screwdriver into the battery removal slot and sliding the battery forward and upward being careful not to damage the electronic board underneath.  Battery replacement install the new battery into the key fob, making sure the positive (+) side is facing up.  Slide the battery until it is seated securely below the tabs.  Reassemble the back cover making sure it is properly aligned before snapping it back in place.  Note: Customers are recommended to use a battery obtained from Mopar\u00ae.  Aftermarket coin", "in place.  Note: Customers are recommended to use a battery obtained from Mopar\u00ae.  Aftermarket coin battery dimensions may not meet the original OEM coin battery dimensions.  Perchlorate material \u2014 special handling may apply.  See www.dtsc.ca.gov/hazardouswaste/perchlorate for further information.  Do not touch the battery terminals that are on the back housing or the printed circuit board.  When a key fob battery is low, a warning will be indicated on the vehicle\u2019s instrument cluster, and the fob LED will no longer illuminate with a button push.  WARNING: The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop", "and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.", "facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical", "integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  The battery in your vehicle is located in the right rear of the engine compartment.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  The Power Distribution Center is located", "on the passenger side under the instrument panel.  The Power Distribution Center is located in the engine compartment near the battery.  This center contains cartridge fuses, mini fuses, and relays.  The PDC top cover is labeled with each serviceable fuse/relay location, function, and size.", "Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  WARNING: Fast spinning tires can be dangerous.  Forces generated by excessive wheel speeds may cause tire damage or failure.  A tire could explode and injure someone.  Do not spin your vehicle's wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.  Off-Road Driving Tips  When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your", "dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and", "automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the", "any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.", "Materials Added To Fuel Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Designated TOP TIER Detergent Gasoline contains a higher level of detergents to further aide in minimizing engine and fuel system deposits.  When available, the usage of TOP TIER Detergent Gasoline is recommended.  Visit www.toptiergas.com for a list of top tier detergent gasoline retailers.  Indiscriminate use of fuel system cleaning agents should be avoided.  Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients.  These can harm fuel system gasket and diaphragm materials.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.", "to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Biodiesel fuel may gel or solidify at low ambient temperatures, which may pose problems for both storage and operation.  Precautions can be necessary at low ambient temperatures, such as storing the fuel in a heated building or a heated storage tank, or using cold temperature additives.  Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from", "fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition", "and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  Methylcyclopentadienyl Manganese Tricarbonyl (MMT) In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasolines to increase octane.  Gasoline", "metallic additive that is blended into some gasolines to increase octane.  Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT.  Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles.  The manufacturer recommends that gasoline without MMT be used in your vehicle.  The MMT content of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gasoline retailer whether the gasoline contains MMT.  MMT is prohibited in Federal law and California reformulated gasoline.", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.", "brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the", "to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second", "to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWRWARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make", "of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  For further information on GAWRs, vehicle loading, and trailer towing, see", "When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD", "REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted", "the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to", "is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High,", "view is pressed.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.", "Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the", "Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the", "or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.  INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the", "vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.", "Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Note: Vehicle speeds shown in the preceding chart are for 2H and 4H only.  Vehicle speeds in 4L would be significantly less.  To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Make certain that the load is secured in the trailer and that it will not shift during travel.  When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.  You could lose control of", "load shifts can occur that may be difficult for the driver to control.  You could lose control of your vehicle and have a collision.  When hauling cargo, or towing a trailer, do not overload your vehicle or trailer.  Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.  Safety chains must always be used between your vehicle and trailer.  Always connect the chains to the frame or hook retainers of the vehicle hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be parked on a grade.  When parking, apply the parking brake on the tow vehicle.  Put the tow vehicle transmission in PARK.  Always block or \"chock\" the trailer wheels.  GCWR must not be exceeded.  Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: GVWR GTW GAWR Tongue weight rating for the trailer", "the following four ratings are not exceeded: GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing a heavy trailer), use the AutoStick shift control to select a lower gear Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  Recommended Vehicle Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart.  Shift at the vehicle speeds listed for acceleration.  When heavily loaded or pulling a trailer, these recommended up shift speeds may not apply.  Note: Vehicle speeds shown in the preceding chart are for 2H and 4H only.  Vehicle speeds in 4L would be significantly less.  Manual transmission shift speeds in mph (km/h)", "Vehicle speeds in 4L would be significantly less.  Manual transmission shift speeds in mph (km/h) engine speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.6l accel.  15 (24) 24 (39) 50 (80) 65 (104) 70 (112) cruise 10 (16) 19 (31) 40 (64) 55 (88) 65 (105) 8\u2013speed automatic transmission the transmission gear range (prndm) is displayed both beside the gear selector and in the instrument cluster.  To select a gear range, push the lock button on the gear selector and move the selector rearward or forward.  To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.  You must also press the brake pedal to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is stopped or moving at low speeds.  Select the DRIVE range for normal driving.  The electronically controlled transmission adapts its shift schedule based on driver inputs, along with environmental and road conditions.  The transmission electronics are self-calibrating; therefore, the first few shifts on a new", "The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt.  This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers).  Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped.  Be sure to keep your foot on the brake pedal when shifting between these gears.  The transmission gear selector provides PARK, REVERSE, NEUTRAL, DRIVE and MANUAL (AutoStick) shift positions.  Manual shifts can be made using the AutoStick shift control.  Toggling the gear selector forward (-) or rearward (+) while in the MANUAL (AutoStick) position (beside the DRIVE position) will manually select the transmission gear, and will display the current gear in the instrument cluster Note: In the event of a mismatch between the gear selector position and the actual transmission gear (for example, driver selects PARK while driving), the position indicator will blink continuously", "(for example, driver selects PARK while driving), the position indicator will blink continuously until the selector is returned to the proper position, or the requested shift can be completed.  Note: If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action", "function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After", "Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected", "conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Service ACC/FCW Warning If the system turns off, and the instrument cluster display reads \u201cACC/FCW Unavailable Service Required\u201d or \u201cCruise/FCW Unavailable Service Required\u201d, there may be an internal system fault or a temporary malfunction that limits ACC functionality.  Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.  If this occurs, try activating ACC again later, following an ignition cycle.  If the problem persists, see an authorized dealer.  Your vehicle may be equipped with a protective cover that is to be used whenever the windshield is folded down in order to protect the ACC/FCW sensor.  To install the cover, refer to the following instructions: If the \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the radar sensor realigned at an authorized dealer.  The \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d warning will display and a chime", "dealer.  The \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d warning will display and a chime will sound when conditions temporarily limit system performance.  Always keep the sensor clean.  Carefully wipe the sensor lens with a soft cloth.  Be cautious not to damage the sensor lens.  Do not remove any screws from the sensor.  Doing so could cause an ACC system malfunction or failure and require a sensor realignment.  If the sensor or front end of the vehicle is damaged due to a collision, see an authorized dealer for service.  Do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles.  Doing so could cause an ACC system failure or malfunction.  If the \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d warning is active, Fixed Speed Cruise Control is still available.  The \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d warning will display and a chime will sound when conditions temporarily limit system performance.  This most often occurs at times of poor", "when conditions temporarily limit system performance.  This most often occurs at times of poor visibility, such as in snow or heavy rain and fog.  The ACC system may also become temporarily blinded due to obstructions, such as mud, dirt, or ice on windshield and fog on the inside of glass.  In these cases, the instrument cluster display will read \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d and the system will have degraded performance.  If the instrument cluster displays \u201cACC/FCW Limited Functionality\u201d or \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d momentarily, there may be a condition that limits FCW functionality.  Although the vehicle is still drivable under normal conditions, the active braking may not be fully available.  Once the condition that limited the system performance is no longer present, the system will return to its full performance state.  If the problem persists, see an authorized dealer.  If the system turns off, and the instrument cluster display reads \u201cACC/FCW", "an authorized dealer.  If the system turns off, and the instrument cluster display reads \u201cACC/FCW Unavailable Service Required\u201d or \u201cCruise/FCW Unavailable Service Required\u201d, there may be an internal system fault or a temporary malfunction that limits ACC functionality.  Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.  If this occurs, try activating ACC again later, following an ignition cycle.  If the problem persists, see an authorized dealer.  This message can sometimes be displayed while driving in adverse weather conditions.  The ACC/FCW system will recover after the vehicle has left these areas.  Under rare conditions, when the camera is not tracking any vehicles or objects in its path this warning may temporarily occur.  Changing the FCW status to \u201cOnly Warning\u201d prevents the system from providing limited active braking, or additional brake support if the driver is not braking adequately in the event of a potential frontal collision, but maintains the", "driver is not braking adequately in the event of a potential frontal collision, but maintains the audible and visual warnings.  Changing the FCW status to \u201cOff\u201d prevents the system from providing autonomous braking, or additional brake support if the driver is not braking adequately in the event of a potential frontal collision.  The system will retain the last setting selected by the driver after ignition shut down.  FCW may not react to irrelevant objects such as overhead objects, ground reflections, objects not in the path of the vehicle, stationary objects that are far away, oncoming traffic, or leading vehicles with the same or higher rates of speed.  FCW will be disabled like ACC, with the unavailable screens.  Driver Assist \u2014 If Equipped The Driver Assist menu displays the status of the ACC system.  Push and release the up or down arrow button until the driver assist menu is displayed in the instrument cluster display.", "To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c.20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately", "your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov .  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the", "has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved", "is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not", "5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.", "Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.  Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle.  These kinds of hitches are commonly used to tow small and medium sized trailers.  Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.  Trailer hitch classification definitions class max.  Trailer hitch industry standards class i - light duty 2,000 lb (907 kg) class ii - medium duty 3,500 lb (1,587 kg) class iii - heavy duty 6,000 lb (2,722 kg) class iv - extra heavy duty 10,000 lb", "lb (1,587 kg) class iii - heavy duty 6,000 lb (2,722 kg) class iv - extra heavy duty 10,000 lb (4,535 kg) refer to the \u201ctrailer towing weights (maximum trailer weight ratings)\u201d chart for the maximum gross trailer weight (gtw) towable for your given drivetrain in this section.  All trailer hitches should be professionally installed on your vehicle.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch", "and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.", "The ignition switch must be in the ACC or ON/RUN position to adjust the power mirrors.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the", "unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP", "is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: The message will stay active until the ignition is placed in the ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster", "START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  To insert an Auxiliary device, gently insert the Auxiliary device cable into the AUX port.  If you insert an Auxiliary device with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system will automatically time out and the ignition will cycle to the OFF position after 30", "The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn", "is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, see These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.", "If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is", "center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator,", "After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough", "not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up", "high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.", "Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A", "vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all", "system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not", "you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition", "for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition", "or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.", "If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  OFF ROAD+ will not function in Two-Wheel Drive High (2H) mode.  If the button is pushed while in 2H mode, the cluster display will show the message \u201cOFF ROAD+ Unavailable Shift to 4WD\u201d.  The ASSIST button is used to automatically connect you to any one of the following support centers: Once the 4G Wi-Fi Hotspot is purchased, you can change its name and the password by selecting the Wi-Fi Hotspot App and pressing the Setup Wi-Fi Hotspot button.  You can also view the connected devices from the app screen by pressing the View Connected Devices button.  If equipped, the ASSIST Button is used for contacting", "pressing the View Connected Devices button.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  1 \u2014 Assist Button 2 \u2014 SOS Button The driver should NEVER use the 4G Wi-Fi Hotspot while driving the vehicle as doing so may result in an accident involving serious injury or death.  ASSIST AND SOS SYSTEM \u2014 IF EQUIPPED If equipped, the overhead console contains an ASSIST and an SOS button.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the", "ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  ASSIST AND SOS SYSTEM \u2014 IF EQUIPPED If equipped, the overhead console contains an ASSIST and an SOS button.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering", "traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  Off Road+ Display \u2014 If Equipped When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will", "messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: 2h: off road+ unavailable, shift to 4wd 4h: 4wd high off road+ active 4l: 4wd low off road+ active adaptive cruise control (acc) and cruise control are not available when using off road+.  If either option is selected, a dedicated message will display indicating that the features are not usable concurrently.  Messages are as follows: 4h: cruise control \u2014 cruise control unavailable in off road+ 4h: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in off road+ 4l: cruise control \u2014 cruise control unavailable in 4wd low 4l: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in 4wd low note: the behavior of electronic stability control while in off road+ varies depending on the 4wd status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also,", "4wd status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also, holding the ESC OFF button for five seconds will turn off ESC.  In 4WD Low, Electronic Stability Control automatically shuts off regardless of the Off Road Status.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons", "The Jeep\u00ae wireless speaker is located behind the right rear passenger seat.  In order to access the Jeep\u00ae wireless speaker, the seat will need to be folded down or tilted forward.  A feature of the Jeep\u00ae wireless speaker is the ability for the Jeep\u00ae wireless speaker to connect to devices using Bluetooth\u00ae.  Follow these simple steps to connect a Bluetooth\u00ae-enabled device to the Jeep\u00ae wireless speaker: To remove the Jeep\u00ae wireless speaker, pull on the strap located on top of the mount for the speaker.  When the strap is pulled, the Jeep\u00ae wireless speaker can easily be lifted from the mount.  Jeep\u00ae Wireless Speaker Location The Jeep\u00ae wireless speaker is located behind the right rear passenger seat.  In order to access the Jeep\u00ae wireless speaker, the seat will need to be folded down or tilted forward.  To remove the Jeep\u00ae wireless speaker, pull on the strap located on top of the mount for the speaker.  When the strap is pulled, the Jeep\u00ae wireless speaker can easily be lifted from the mount.  When placing the", "strap is pulled, the Jeep\u00ae wireless speaker can easily be lifted from the mount.  When placing the Jeep\u00ae wireless speaker back in the mount, simply put the speaker back in the mount.  Then push/rotate forward on the front of the speaker until the speaker locks in place.  Charging The Speaker Before using the Jeep\u00ae wireless speaker for the first time, fully charge your Jeep\u00ae wireless speaker until the battery indicator light stays solid green.  The Jeep\u00ae wireless speaker in-vehicle dock is the most ideal way to fully charge the speaker with the ignition in ON/RUN or ACC.  The speaker can also be charged with a power adapter.  To charge the Jeep\u00ae wireless speaker with a power adapter, insert the power adapter into a wall outlet.  Next, plug the power adapter into the Jeep\u00ae wireless speaker charging port on the back of the speaker.  Note: Jeep\u00ae wireless speaker will not charge within vehicle dock while the ignition is fully off.  Note: Power adapter needed for the Jeep\u00ae wireless speaker has to have a range of", "is fully off.  Note: Power adapter needed for the Jeep\u00ae wireless speaker has to have a range of 14 VDC to 16.5 VDC, with a minimum of 2.7A and a barrel connector dimension of 5.5 mm by 2.5 mm.  Power adapter is not included.", "Safety Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.  WARNING: Improperly inflated tires are dangerous and can cause collisions.  Underinflation increases tire flexing and can result in overheating and tire failure.  Overinflation reduces a tire's ability to cushion shock.  Objects on the road and chuckholes can cause damage that result in tire failure.  Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.  Unequal tire pressures can cause steering problems.  You could lose control of your vehicle.  Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.  Always drive with each tire inflated to the recommended cold tire inflation pressure.  Note: Unequal tire pressures from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure", "from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure from side to side may cause the vehicle to drift left or right.  FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.", "turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of", "load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure", "abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Temperature Grades The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not", "The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.  Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.", "Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety", "any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html frequently asked questions about installing child restraints with seat belts what is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor", "is the weight limit (child\u2019s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward-facing child restraint.  Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward-facing child restraint, up to the recommended weight limit of the child restraint.  Can the rear-facing child restraint touch the back of the front passenger seat?  Yes contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.  Can the rear head restraints be removed?  Yes the center head restraint can be removed if it interferes with the installation of the child restraint.  Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint?  No do not twist the buckle stalk in a seating position with an alr retractor.  Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and", "Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.  Use this simple 5-step test to decide whether the child can use the vehicle\u2019s seat belt alone: Can the child sit all the way back against the back of the vehicle seat?  Do the child\u2019s knees bend comfortably over the front of the vehicle seat while the child is still sitting all the way back?  Does the shoulder belt cross the child\u2019s shoulder between the neck and arm?  Is the lap part of the belt as low as possible, touching the child\u2019s thighs and not the stomach?  Can the child stay seated like this for the whole trip?  If the answer to any of these questions was \u201cno,\u201d then the child still needs to use a booster seat in this vehicle.  If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s", "belt, check seat belt fit periodically and make sure the seat belt buckle is latched.  A child\u2019s squirming or slouching can move the belt out of position.  If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.  WARNING: Never allow a child to put the shoulder belt under an arm or behind their back.  In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.  A child must always wear both the lap and shoulder portions of the seat belt correctly.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to", "12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter", "hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  Important Safety Precautions Please pay close attention to the information in this section.  It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.  Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: Children 12 years old and under should always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be", "with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint Never allow children to slide the shoulder belt behind them or under their arm.  You should read the instructions provided with your child restraint to make sure that you are using it properly.  All occupants should always wear their lap and shoulder belts properly.  The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate.  Do not lean against the door or window.  If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.  If the air bag system in", "the space between occupants and the door and occupants could be injured.  If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see \"\u21e8if you need assistance\" for customer service contact information.  WARNING: Never place a rear-facing child restraint in front of an air bag.  A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.  Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing child restraint in the rear seat.  If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle.", "To Arm The System Follow these steps to arm the Vehicle Security system: Make sure the vehicle\u2019s ignition is placed in the OFF position.  Perform one of the following methods to lock the vehicle: push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zonePush the lock button on the key fob.  If any doors are open, close them.  Note: The Vehicle Security system will not arm if you lock the doors using the manual door lock.  To Arm The System Follow these steps to arm the Vehicle Security system: Make sure the vehicle\u2019s ignition is placed in the OFF position.  Perform one of the following methods to lock the vehicle: push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone Push the", "Passive Entry door handle with a valid key fob available in the same exterior zone Push the lock button on the key fob.  If any doors are open, close them.  Note: The Vehicle Security system will not arm if you lock the doors using the manual door lock.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic,", "disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two", "but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle", "When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Conditions that will cause the engine to start automatically while in stop/start autostop active mode, the engine will start automatically when: actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode stop/start autostop active time exceeds five minutes battery voltage drops too low vehicle is moving faster than 5 mph (8 km/h) stop/start off switch is pressed transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold (ess models only) to start the engine while in autostop mode while in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is pressed.  The transmission will automatically re-engage upon engine restart.  Conditions that will cause the engine to start automatically while in autostop mode: the transmission selector is moved out of drive to maintain cabin temperature comfort actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to", "cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode hvac system temperature or fan speed is manually adjusted battery voltage drops too low stop/start off switch is pushed a stop/start system error occurs stop/start autostop active time exceeds five minutes transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold.  Conditions that will cause the engine to start automatically while in stop/start autostop active mode, the engine will start automatically when: actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode stop/start autostop active time exceeds five minutes battery voltage drops too low vehicle is moving faster than 5 mph (8 km/h) stop/start off switch is pressed transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold (ess models only).  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.", "The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine", "will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24", "by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).", "When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.", "jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or", "with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash", "other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.", "connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the", "post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.", "Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201dWARNING:", "Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201dWARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may", "safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle", "unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for", "switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned", "operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates", "temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine", "for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be", "when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool;", "upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a", "indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the", "switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.", "What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be", "cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  What", "as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations", "effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Wheel And Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Your wheels are susceptible to deterioration caused by salt, sodium chloride, magnesium chloride, calcium chloride, etc., and other road chemicals used to melt ice or control dust on dirt roads.  Use a soft cloth or sponge and mild soap to wipe away promptly.  Do not use harsh chemicals or a stiff brush.  They can damage the wheel\u2019s protective coating that helps keep them from corroding and tarnishing.  When cleaning extremely dirty wheels, including", "helps keep them from corroding and tarnishing.  When cleaning extremely dirty wheels, including excessive brake dust, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels.  Mopar\u00ae Wheel Treatment or Mopar\u00ae Chrome Cleaner, or their equivalent, is recommended or select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels.  CAUTION: Avoid products or automatic car washes that use acidic solutions or strong alkaline additives or harsh brushes.  Many aftermarket wheel cleaners and automatic car washes may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  CAUTION: Do not use scouring pads, steel wool, a bristle brush, metal polishes, or oven cleaner.  These products may damage the wheel's protective finish.  Such damage is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner", "is not covered by the New Vehicle Limited Warranty.  Only car wash soap, Mopar\u00ae Wheel Cleaner or equivalent is recommended.  Note: If you intend parking or storing your vehicle for an extended period after cleaning the wheels with wheel cleaner, drive your vehicle and apply the brakes to remove the water droplets from the brake components.  This activity will remove the red rust on the brake rotors and prevent vehicle vibration when braking.", "If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  When parking on a hill, apply the parking brake before shifting the transmission to PARK.  As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel", "Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce,", "the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.", "requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the", "headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start", "the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the", "system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.", "Feature description controls \u2014 if equipped press the controls button to access vehicle-specific features like heated seats and steering wheel.  Apps press the apps button to access a list of the available mobile apps.  Climate press the climate button to enter climate mode and access the climate control functions.  Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF.  Climate Control OFF Button Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  Feature description controls \u2014 if equipped press the controls button to access vehicle-specific features like heated seats and steering wheel.  Apps press the apps button to access a list of the available mobile apps.  Climate press the climate button to enter climate mode and access the climate control functions \"\u21e8climate controls\" .  Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF.", "Maintenance Plan Refer to the maintenance plan for the required maintenance intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to prevent premature wear.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Maintenance Plan \u2014 Diesel Fuel Up To B5 Biodiesel Refer to the Maintenance Plans for required maintenance.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly", "ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Drain And Refill For the proper maintenance intervals  Maintenance Plan \u2014 Diesel Fuel Up To B5 Biodiesel Refer to the Maintenance Plans for required maintenance.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.  Maintenance Plan Refer to the maintenance plan for the required maintenance intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to", "intervals.  Note: Using white lithium grease, lubricate the door hinge joints twice a year to prevent premature wear.  WARNING: You can be badly injured working on or around a motor vehicle.  Do only service work for which you have the knowledge and the right equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance.  This could cause an accident.", "AutoStick AutoStick is a driver-interactive transmission feature providing manual shift control, giving you more control of the vehicle.  AutoStick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance.  This feature can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.  Operation To activate AutoStick mode, move the gear selector into the MANUAL (M) position (beside the DRIVE position).  The current transmission gear will be displayed in the instrument cluster.  In AutoStick mode, you can use the gear selector (in the MANUAL position) to manually shift the transmission.  Tapping the gear selector forward (-) while in the MANUAL (M) position will downshift the transmission to the next lower gear.  Tapping the selector rearward (+) will command an upshift.  In AutoStick mode, the transmission will shift up or down when (+/-) is manually", "an upshift.  In AutoStick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result.  It will remain in the selected gear until another upshift or downshift is chosen, except as follows: The transmission will automatically downshift as the vehicle slows (to prevent engine lugging) and will display the current gear.  The transmission will automatically downshift to FIRST gear when coming to a stop.  After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or THIRD gear, in 4L range).  Tapping (+) (at a stop) will allow starting in SECOND gear.  Starting out in SECOND or THIRD gear can be helpful in snowy or icy conditions.  If a requested downshift would cause the engine to overspeed, that shift will not occur.  The system will ignore attempts to upshift at too low of a vehicle speed.  Holding the gear selector in", "system will ignore attempts to upshift at too low of a vehicle speed.  Holding the gear selector in the (-) position will downshift the transmission to the lowest gear possible at the current speed.  Transmission shifting will be more noticeable when AutoStick is enabled.  The system may revert to automatic shift mode if a fault or overheat condition is detected.  To disengage AutoStick mode, return the gear selector to the DRIVE position.  You can shift in or out of the AutoStick position at any time without taking your foot off the accelerator pedal.  Note: When Hill Descent Control is enabled, AutoStick is not active.  WARNING: Do not downshift for additional engine braking on a slippery surface.  The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury.  When using the AutoStick shift control, select the highest gear that allows for adequate performance and avoids frequent downshifts.  For example, choose \u201c5\u201d if the desired speed can be maintained.  Choose", "frequent downshifts.  For example, choose \u201c5\u201d if the desired speed can be maintained.  Choose \u201c4\u201d or \u201c3\u201d if needed to maintain the desired speed.  To prevent excess heat generation, avoid continuous driving at high RPM.  Return to a higher gear or vehicle speed when grade and road conditions allow.  Pushing the set (+) , or set (-) button once will result in a 1 km/h speed adjustment.  Each subsequent tap of the button results in an adjustment of 1 km/h.  If the button is continually pushed, the set speed will continue to adjust in 10 km/h increments until the button is released, then the new set speed will be established.  Pushing the set (+) , or set (-) button once will result in a 1 km/h speed adjustment.  Each subsequent tap of the button results in an adjustment of 1 km/h.  If the button is continually pushed, the set speed will continue to adjust in 10 km/h increments until the button is released,The new set speed is reflected in the instrument cluster display.", "Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  When vehicle speed becomes too high to display the pitch and roll, \u201c- -\u201d will display in place of the numbers, and the graphic will be grayed out.  A message indicating the necessary speed for the feature to become available will also display.  The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  When the Display button is pressed on the touchscreen, the system will display the options related to the theme (if equipped), brightness, and color of the touchscreen.  The available settings are: Depending on the vehicle\u2019s options, feature settings may vary.  Touchscreen The Automatic Dimming feature can be turned on or off through", "settings may vary.  Touchscreen The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Push the blue button on the faceplate or touchscreen or press and slide the temperature bar towards the blue arrow button on the touchscreen for cooler temperature settings.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directions When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the", "begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: Become familiar with the Uconnect features and applications in this vehicle before you drive on the roadway so using Uconnect will be more intuitive and will not require prolonged viewing of the screen while you are driving.  When driving, looking at the touchscreen should only be done by a glance when safe to do so.  If prolonged viewing of the screen is required, choose a safe and secure location where you can pull over and park safely to do so.  Stop use immediately if a problem occurs.  Failure to do so may cause injury or damage to the product.  See an authorized dealer for repair.  Ensure the volume level of the system is set to a level that still allows you to hear outside traffic and emergency vehicles.  When making a selection, only press one button at a time to enter the desired menu.", "vehicles.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase", "are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster", "Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to", "buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.", "Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  WARNING: Fast spinning tires can be dangerous.  Forces generated by excessive wheel speeds may cause tire damage or failure.  A tire could explode and injure someone.  Do not spin your vehicle's wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.  When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering,", "grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D)", "push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely", "and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Downhill Before driving down a steep hill, you need to determine if it is too steep for a safe descent.  What is the surface traction?  Is the grade too steep to maintain a slow, controlled descent?  Are there obstacles?  Is it a straight descent?  Is there plenty of distance at the base of the hill to regain control if the vehicle descends too fast?  If you feel confident", "at the base of the hill to regain control if the vehicle descends too fast?  If you feel confident in your ability to proceed, then make sure you are in 4L and proceed with caution.  Allow engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: Do not descend a steep grade in NEUTRAL.  Use vehicle brakes in conjunction with engine braking.  Descending a grade too fast could cause you to lose control and be seriously injured or killed.  Off-Road Driving Tips", "The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  To install the sunrider\u00ae soft top, proceed as follows: lowering the soft top \u00b9 use this qr code to access your digital experience.  Lowering The Soft Top Into The Sunrider\u00ae Position: From the Sunrider\u00ae Position, remove straps if previously secured.  Step One Failure to follow the next steps could result in damage to the soft top or vehicle.  Using the side link, lift and push the soft top toward the front of the vehicle, manually guiding the top into the closed position.  Step Two Step Two From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Step Three Pull the handle back upward while squeezing the hook, locking the latch into place.  Lowering the soft top into the sunrider\u00ae position: lowering the soft top \u00b9 use this qr code to access your digital experience.  Fold both sun visors forward against", "top \u00b9 use this qr code to access your digital experience.  Fold both sun visors forward against the windshield.  Release the header latches from the crossbar by pulling the handle downward.  Make sure the hook is fully disengaged from its receiver.  Step two from both the left and right sides, lift up on the #1 bow of the soft top to begin the operation.  It is recommended to utilize two people for this procedure.  Step three move to the side of the vehicle and use the side link to fold the soft top rearward.  Step four secure the top in this position by using the two hook-and-loop fasteners provided in the center console.  Step Five Note: The vehicle can be driven in the Sunrider\u00ae Position with the rear window and quarter panel cover assemblies fully installed or completely removed.  CAUTION: Quarter panel cover assemblies and rear window must be either all in or all out.  Removing the soft top removing the soft top \u00b9 use this qr code to access your digital experience.  Fully lower the soft top to the", "the soft top \u00b9 use this qr code to access your digital experience.  Fully lower the soft top to the Sunrider\u00ae positionCaution: failure to follow the next steps could result in damage to the soft top or vehicle.  Using the provided #T50 Torx head driver and ratchet, unscrew the two Torx head fasteners on the inside of each top mechanism.  Step two utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle\u2019s sport bar and trim.  Store the soft top in a safe, clean, and dry location.  Remove the door frames.  The rear door frames must be removed before the front door framesUsing the provided #T50 Torx head driver and ratchet, unscrew the six Torx head fasteners on both rear corners and the back of the cab, then remove the belt rail.  Note: folding down the rear seats is recommended to provide easier access to the fasteners.  Step five 1 \u2014 corner fasteners 2 \u2014 rear fasteners.", "Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d", "and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.", "of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear", "Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as", "bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and", "up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up", "the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear", "can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.", "Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d", "and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.", "of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear", "Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as", "bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.", "Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Follow the recommended maintenance intervals as shown in the Maintenance Schedule in this section.  For the proper maintenance intervals The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.  Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message  SCHEDULED SERVICING \u2014 GASOLINE ENGINE", "other than an authorized dealer, to reset the message  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will", "cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.", "The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  Power Door Lock Switch Push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone Push the lock button on the key fob.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked", "injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control", "will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Rear Seat Unoccupied Indicator Light \u2014 If Equipped This light indicates when the rear passenger seats are unoccupied, and will illuminate in the upper right portion of the instrument cluster display, momentarily replacing the configurable corner information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back", "by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are", "to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure", "using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the", "will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Trailer And Tongue Weight Never exceed the maximum tongue weight stamped on your bumper or trailer hitch.  Consider the following items when computing the weight on the rear axle of the vehicle: the tongue weight of the trailer the weight of any other type of cargo or equipment put in or on your vehicle the weight of the driver and all passengers note: remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is", "weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids,", "Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.", "Installing The Rear Window And Quarter Panel Cover Assemblies If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: Guide the top of the quarter panel cover assembly up into the retainer.  Step one caution: failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the soft top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide the rear window into the retainer while keeping the window level.  Step four engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the", "window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step five engage the vertical retainers up the right and left side of the rear window.  Step six tuck the rear window under the soft top fabric and press firmly.  Step seven engage the rear window retainers in the lower right and left corners.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do", "level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be", "or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Installing The Rear Window And Quarter Panel Cover Assemblies If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: Guide the top of the quarter panel cover assembly up into the retainer.  Step one caution: failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the soft top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide the rear window into the retainer while keeping the window level.  Step four engage the", "side, guide the rear window into the retainer while keeping the window level.  Step four engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step five engage the vertical retainers up the right and left side of the rear window.  Step six tuck the rear window under the soft top fabric and press firmly.  Step seven engage the rear window retainers in the lower right and left corners.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  CAUTION: Manual Sliding Rear Window \u2014 If Equipped To open the rear sliding window, push the release button inward while sliding the window into the open position.  Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps", "And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom,", "on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Installing The Rear Window And Quarter Panel Cover Assemblies If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: Guide the top of the quarter panel cover assembly up into the retainer.  Step one caution: failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the soft top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the", "of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide the rear window into the retainer while keeping the window level.  Step four engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step five engage the vertical retainers up the right and left side of the rear window.  Step six tuck the rear window under the soft top fabric and press firmly.  Step seven engage the rear window retainers in the lower right and left corners.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or", "Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  CAUTION: Soft Top Rear Window Storage Bag \u2014 If Equipped To safely store the soft top rear window, proceed as follows: With the bag opened completely, fold the fabric divider downward and lay the rear window in the bottom of the bag.  Step one fold the divider upward, covering the rear window.  Step two lay the first quarter panel cover assembly all the way to the right side and the second quarter panel cover assembly on the left side.  Secure both using the two hook-and-loop fastener straps on each side.  Note: the quarter panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step three 1 \u2014 left quarter panel cover assembly 2 \u2014 right quarter panel cover assembly close the storage bag and store in a safe location.", "Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWRWARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do", "and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  On-Road Driving Tips Utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications.  Specific design characteristics give them a higher center of gravity than conventional passenger cars.  An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems.  They are not designed for cornering at the same speeds as conventional passenger cars any more than low-slung sports cars are designed to perform satisfactorily in off-road conditions.  Avoid sharp turns or abrupt maneuvers.  As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover.  Driving Across An Incline If", "vehicle correctly may result in loss of control or vehicle rollover.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying", "this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced", "a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly", "not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.", "System Malfunction If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  In following situations the engine will not stop: driver\u2019s seat belt is not buckled outside temperature is less than 10\u00b0f (\u201312\u00b0c) or greater than 109\u00b0f (43\u00b0c) actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode engine has not reached normal operating temperature battery is discharged when driving in reverse hood is open transfer case is in 4l or n (neutral) driver's seat is not occupied or driver door is open vehicle is at", "case is in 4l or n (neutral) driver's seat is not occupied or driver door is open vehicle is at high altitude the vehicle is on a steep grade forward gear is engaged steering angle is beyond threshold system fault is present hvac is set to max a/c it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has", "is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about", "check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system", "steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal", "to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  In following situations the engine will not stop: driver\u2019s seat belt is not buckled outside temperature is less than 10\u00b0f (\u201312\u00b0c) or greater than 109\u00b0f (43\u00b0c)", "seat belt is not buckled outside temperature is less than 10\u00b0f (\u201312\u00b0c) or greater than 109\u00b0f (43\u00b0c) actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode engine has not reached normal operating temperature battery is discharged when driving in reverse hood is open transfer case is in 4l or n (neutral) driver's seat is not occupied or driver door is open vehicle is at high altitude the vehicle is on a steep grade forward gear is engaged steering angle is beyond threshold system fault is present hvac is set to max a/c it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  To Start The Engine While In Autostop Mode When the gear selector is in NEUTRAL, the engine will start when the clutch pedal is pressed (does not require complete/full pedal press).  The vehicle will go into STOP/START SYSTEM NOT READY mode", "not require complete/full pedal press).  The vehicle will go into STOP/START SYSTEM NOT READY mode until the vehicle speed is greater than 5 mph (8 km/h).", "Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to", "of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Lock press this button to lock your vehicle.  Vehicle start press this button to start your vehicle.  Horn & lights press this button to sound the horn and activate your lights.  Unlock press this button to unlock your vehicle.  Cancel vehicle", "horn and activate your lights.  Unlock press this button to unlock your vehicle.  Cancel vehicle start press this button to cancel remote start.  Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.", "When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1", "Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided", "the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners Loosen the fasteners from the engine air cleaner filter cover using a suitable tool.  Engine Air Cleaner Filter Cover 1 \u2014 Fasteners 2 \u2014 Engine Air Cleaner Filter Cover Lift the engine air cleaner filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from the housing assembly.  engine air cleaner filter cover  Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For", "Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque Specification For Torx Fastener Maximum Minimum 119.5 in-lb (13.5", "torque specifications.  Torque Specification For Torx Fastener Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  Damage to the retainers will occur.  Step One Install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step Four Using the provided #T50 Torx head driver and ratchet, install and tighten the Torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the", "by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step Five Torque Specification For Torx Fasteners Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Step Five Before driving the vehicle with the top in the Sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners Step Six  Installing The Soft Top Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque specification for torx fastener maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.", "n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  Damage to the retainers will occur.  Step one 1 \u2014 corner fasteners 2 \u2014 rear fasteners install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Caution: failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step four using the provided #t50 torx head driver and ratchet, install and tighten the torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the", "until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step five torque specification for torx fasteners maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Step five before driving the vehicle with the top in the sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners.  Step Six Note:", "The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  Bed Rail Tie Down Locations Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.  The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction", "between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Supplemental Seat-Mounted Side Air Bags (SABs) are located in the outboard side of the front seats.  The SABs are marked with a \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d on a label or on the seat trim on the outboard side of the seats.  Four auxiliary switches are located in the lower switch bank of the instrument panel and can be used to power various electrical devices.  1 \u2014 Retainers 2 \u2014 Fuel Filter Protective Cover The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of", "secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should", "load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  Lower Anchors And Tethers For CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.  BED RAIL TIE DOWN SYSTEM \u2014 IF", "restraint.  Please see the following table for more information.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout", "the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.", "Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see \"\u21e8draining fuel/water separator filter \u2014 diesel engine\" .  Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential seeBulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.", "into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Fuel Oxidation Stability \u2014 Must Use Fuel Within Six Months Of Manufacture Biodiesel fuel has poor oxidation stability which can result in long term storage problems.  Fuel produced to approved ASTM standards, if stored properly, provides for protection against fuel oxidation for up to six months.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or", "Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent", "or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range", "Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively", "or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor", "than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  Do Not Operate The Engine With Failed Parts All engine failures give some warning before the parts fail.  Be on the alert for changes in performance, sounds, and visual evidence that the engine requires service.  Some important clues are: engine misfiring or vibrating severely sudden loss of power unusual engine noises fuel, oil or coolant leaks sudden change, outside the normal operating range, in the engine operating temperature excessive smoke oil pressure drop shifting fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is", "when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle", "missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and", "(MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily", "suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  For further information on GAWRs, vehicle loading, and trailer towing, see  The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the", "passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWRThe GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  For further information on GAWRs, vehicle loading, and trailer towing, see Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options", "GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.", "Feature description controls \u2014 if equipped press the controls button to access vehicle-specific features like heated seats and steering wheel.  Apps press the apps button to access a list of the available mobile apps.  Climate press the climate button to enter climate mode and access the climate control functions.  Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF.  Climate Control OFF Button Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.  Feature description controls \u2014 if equipped press the controls button to access vehicle-specific features like heated seats and steering wheel.  Apps press the apps button to access a list of the available mobile apps.  Climate press the climate button to enter climate mode and access the climate control functions \"\u21e8climate", "press the climate button to enter climate mode and access the climate control functions \"\u21e8climate controls\" .", "Conditions that will cause the engine to start automatically while in stop/start autostop active mode, the engine will start automatically when: actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode stop/start autostop active time exceeds five minutes battery voltage drops too low vehicle is moving faster than 5 mph (8 km/h) stop/start off switch is pressed transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold (ess models only) to start the engine while in autostop mode while in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is pressed.  The transmission will automatically re-engage upon engine restart.  Conditions that will cause the engine to start automatically while in autostop mode: the transmission selector is moved out of drive to maintain cabin temperature comfort actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to", "cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode hvac system temperature or fan speed is manually adjusted battery voltage drops too low stop/start off switch is pushed a stop/start system error occurs stop/start autostop active time exceeds five minutes transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold.  Conditions that will cause the engine to start automatically while in stop/start autostop active mode, the engine will start automatically when: actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode stop/start autostop active time exceeds five minutes battery voltage drops too low vehicle is moving faster than 5 mph (8 km/h) stop/start off switch is pressed transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold (ess models only).  To Start The Engine While In Autostop Mode While in a forward gear, the engine will start when the", "To Start The Engine While In Autostop Mode While in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is pressed.  The transmission will automatically re-engage upon engine restart.", "Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try", "the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions:", "familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in", "Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your", "dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely", "the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedureWARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these", "with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is", "If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.", "enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedureWARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The", "high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Priming If The", "\"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with", "agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.", "The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the", "is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below", "to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect", "Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  Installing The Soft Top Install the belt rail on the", "this caution could damage the hard top.  Installing The Soft Top Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque specification for torx fastener maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  Damage to the retainers will occur.  Step one 1 \u2014 corner fasteners 2 \u2014 rear fasteners install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Caution: failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto", "Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step four using the provided #t50 torx head driver and ratchet, install and tighten the torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step five torque specification for torx fasteners maximum minimum 119.5 in-lb (13.5 n\u00b7m) 150.5 in-lb (17.0 n\u00b7m) 106.2 in-lb (12.0 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Step five before driving the vehicle with the top in the sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners.  Step Six Note:  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on", "Step Six Note:  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners", "protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.", "Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.  Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Three-Position Tailgate The", "tailgate is dampened to provide a slower, more controlled lowering.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to", "Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).", "Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an", "information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system", "personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL", "your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.", "Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The", "for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated", "store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a", "occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedureWARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in", "and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine", "the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products", "which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.", "Fuel Filler Cap The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Open the fuel filler door.  Fuel filler door remove the fuel cap by rotating it counterclockwise.  Fuel filler cap fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the", "is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light (MIL) to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  CAUTION: Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Note: When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure", "tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  After fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged.  If the system detects a malfunction, the \u201cgASCAP\u201d message will display in the odometer display.  Tighten the gas cap until a \"clicking\" sound is heard.  This is an indication that the gas cap is properly tightened.  Push the odometer reset button to turn the message off.  If the problem persists, the message will appear the next time the vehicle is started.  This might indicate a", "persists, the message will appear the next time the vehicle is started.  This might indicate a damaged cap.  If the problem is detected twice in a row, the system will turn on the MIL.  Resolving the problem will turn the MIL off.  The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal", "the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the", "belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure", "One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners Loosen the fasteners from the engine air cleaner filter cover using a suitable tool.  Engine Air Cleaner Filter Cover 1 \u2014 Fasteners 2 \u2014 Engine Air Cleaner Filter Cover Lift the engine air cleaner filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from the housing assembly.  engine air cleaner filter cover", "The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  Interior Courtesy Lights When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right)", "the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  To enter the \u201cPartial Off\u201d mode, momentarily push the ESC OFF button and the ESC OFF Indicator Light will illuminate.  To turn the ESC on again, momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door", "momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Automatic Headlight System will turn the headlights on or off according to ambient light levels.  To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation.  When the system is on, the headlight time delay feature is also on.  This means the headlights will stay on for up to 90 seconds (programmable through the uconnect settings \"\u21e8uconnect settings\" ) after you place the ignition into the off position.  To turn the automatic system off, move the headlight switch out of the AUTO position.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the", "The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Reduce power to unnecessary loads if possible: Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed", "settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s exterior and interior lights.  When the \u201cDaytime Running Lights\u201d feature is selected, the daytime running lights can be turned on or off.  This feature is only allowed by law in the country of the vehicle purchase.  Depending on the vehicle\u2019s options, feature settings may vary.  Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to", "lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other", "systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road", "lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5", "fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a", "Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to", "Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Door Frame Installation Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten fasteners target torque specification for torx fasteners maximum minimum 44.2 in-lb (5 n\u00b7m) 53.1 in-lb (6 n\u00b7m) 35.4 in-lb (4 n\u00b7m) caution: do", "torx fasteners maximum minimum 44.2 in-lb (5 n\u00b7m) 53.1 in-lb (6 n\u00b7m) 35.4 in-lb (4 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step five step five insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the", "each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.", "Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  From the Sunrider\u00ae Position, remove straps if previously secured.  Step One Failure to follow the next steps could result in damage to the soft top or vehicle.  Using the side link, lift and push the soft top toward the front of the vehicle, manually guiding the top into the closed position.  Step Two Step Two From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Step Three Pull the handle back upward while squeezing the hook, locking the latch into place.  Step Four It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and", "while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Soft Top Rear Window Storage Bag \u2014 If Equipped To safely store the soft top rear window, proceed as follows: With the bag opened completely, fold the fabric divider downward and lay the rear window in the bottom of the bag.  Step one fold the divider upward, covering the rear window.  Step two lay the first quarter panel cover assembly all the way to the right side and the second quarter panel cover assembly on the left side.  Secure both using the two hook-and-loop fastener straps on each side.  Note: the quarter panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step three 1 \u2014 left quarter panel cover assembly 2 \u2014 right quarter panel cover assembly", "assembly.  Step three 1 \u2014 left quarter panel cover assembly 2 \u2014 right quarter panel cover assembly close the storage bag and store in a safe location.  Installing The Rear Window And Quarter Panel Cover Assemblies If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: Guide the top of the quarter panel cover assembly up into the retainer.  Step one caution: failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the soft top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide the rear window into the retainer while keeping the window level.  Step four", "either side, guide the rear window into the retainer while keeping the window level.  Step four engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step five engage the vertical retainers up the right and left side of the rear window.  Step six tuck the rear window under the soft top fabric and press firmly.  Step seven engage the rear window retainers in the lower right and left corners.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.", "Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set", "the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.", "To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c.20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately", "your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov .  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the", "has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved", "is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not", "5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.", "Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  1 \u2014 Upper Console Storage Latch 2 \u2014 Lower Console Storage Latch To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock", "the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.", "The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is", "will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering", "not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel", "as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The engine must be running for the heated steering wheel to operate.", "When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route", "ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no", "to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  Mud Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get", "debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any", "The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These", "to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it", "for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the", "Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  The instrument cluster display features a driver interactive displayThe Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The instrument cluster display will show the current ACC system settings.  The Instrument Cluster Display is located in the center of the instrument cluster.  The information it displays depends on ACC system status.  Instrument Cluster Display Control Buttons The instrument cluster has an SSC icon and the SSC switch has a light that offers feedback to the driver about the state SSC is in.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside", "of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument", "the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  To close the tailgate, lift upward until both sides latch into place.  Opening To open the tailgate, pull the release handle located on the center of the tailgate", "place.  Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.", "Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with", "vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not", "you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced", "control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the", "The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could", "Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or", "for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10", "Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.", "Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug", "surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x", "socket.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.  WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.", "Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.", "the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This warning light will indicate when", "the heater/air conditioning (hvac) air flow will be reduced.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display If an obstacle is detected in the center front region, the display will show a", "cluster display If an obstacle is detected in the center front region, the display will show a single solid arc in the center front region with no chime.  As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and a fast sound tone will be heard and will change from fast, to continuous.  Instrument cluster descriptions tachometer indicates the engine speed in revolutions per minute (rpm x 1000).  Caution: do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature gauge the temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You", "limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Caution: driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument cluster display the instrument cluster display features a driver interactive display.  Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer indicates vehicle speed.  Speedometer push and release the up or down arrow button until", "indicates vehicle speed.  Speedometer push and release the up or down arrow button until the speedometer menu icon is displayed in the instrument cluster display.  Push and release the ok button to toggle between mph and km/h.  Favorite menus speedometer vehicle info off road \u2014 if equipped (show/hide) driver assist \u2014 if equipped (show/hide) fuel economy (show/hide) trip info (show/hide) stop / start \u2014 if equipped audio (show/hide) messages screen setup vehicle settings \u2014 if equipped.  Instrument cluster descriptions tachometer indicates the engine speed in revolutions per minute (rpm x 1000).  Caution: do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature gauge the temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a", "indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Caution: driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument cluster display the instrument cluster display features a driver interactive display.  Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of", "when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer indicates vehicle speed.", "Engine Oil Filter Selection A full-flow type disposable oil filter should be used for replacement.  The quality of replacement filter varies considerably.  We recommend using a Mopar\u00ae engine oil filter, if a Mopar\u00ae engine oil filter is unavailable only use filters that meet or exceed SAE/USCAR-36 Filter performance requirements.  Engine Oil Filter Replacement Residual oil in the housing may spill from the housing when the new filter is installed if the residual oil is not either removed from the housing or enough time has not elapsed to allow the oil to drain back into the engine.  When servicing the oil filter on this engine, open the filter cap approximately six turns until the cap o-ring is visible and stop.  Wait five minutes with the cap in this position to allow dirty engine oil to drain back into the engine.  After five minutes, the cap and filter assembly can be removed and discarded.  Engine Oil Filter The engine oil filter should be replaced with a new filter at every engine oil change.  Engine Oil", "The engine oil filter should be replaced with a new filter at every engine oil change.  Engine Oil Filter Selection A full-flow type disposable oil filter should be used for replacement.  The quality of replacement filter varies considerably.  We recommend using a Mopar\u00ae engine oil filter, if a Mopar\u00ae engine oil filter is unavailable only use filters that meet or exceed SAE/USCAR-36 Filter performance requirements.  Inspect engine air cleaner filter if using in dusty or off-road conditions, replace engine air cleaner filter if necessary.  The engine oil filter should be replaced with a new filter at every engine oil change.  A full-flow type disposable oil filter should be used for replacement.  The quality of replacement filter varies considerably.  We recommend using a Mopar\u00ae engine oil filter, if a Mopar\u00ae engine oil filter is unavailable only use filters that meet or exceed SAE/USCAR-36 Filter performance requirements.  Engine Oil Filter Replacement", "Automatic High Beam Headlamp Control \u2014 If Equipped The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automatically controlling the high beams through the use of a camera mounted on the vehicle\u2019s header.  This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.  Note: the automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.  This mirror automatically adjusts for headlight glare", "cause the system to function improperly.  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.  High/Low Beam Switch The High/Low Beam switch is located within the multifunction lever on", "High/Low Beam Switch The High/Low Beam switch is located within the multifunction lever on the left side of the steering wheel.  High beam headlights can be used for improved visibility in low lit areas when there is no oncoming traffic.  Otherwise, it is recommended to use the low beam headlights to reduce glare to other vehicles.  With the headlight switch activated, push the multifunction lever toward the instrument panel to switch the headlights to high beams.  The lever will return to the centered position.  To return the headlights to low beam, pull the lever toward the steering wheel, or push the lever toward the instrument panel.", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check", "to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following", "If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the", "take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for", "main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Lockout Service Whether the keys are locked in your vehicle or frozen locks are keeping you from getting on your way, help is just a phone call away.  This service is limited to providing access to the vehicle\u2019s seating area.  It does not cover the cost of replacement keys.  VEHICLE MAINTENANCE An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions control systems", "attempting any procedure yourself.  Note: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  WARNING: You can be badly injured working on or around a motor vehicle.  Only do service work for which you have the knowledge and the proper equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.", "Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts", "Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners", "careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it", "bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx", "arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Bumper end caps are removable on steel bumpers only.  The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket", "bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 Bolt #2 Remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step Two 1 \u2014 Hex Bolt Cover Installed 2 \u2014 Hex Bolt Cover Removed Using the provided 15 mm socket, remove the two hex bolts and remove", "2 \u2014 Hex Bolt Cover Removed Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step Six Secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Do Not Overtighten!  Damage to the windshield could result.  Open the fuel filler door.  Fuel Filler Door Remove the fuel cap by rotating it counterclockwise.  Fuel Filler Cap Fully insert the", "Filler Door Remove the fuel cap by rotating it counterclockwise.  Fuel Filler Cap Fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.", "Driving Through Water Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher", "the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  CAUTION: Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  Before You Cross Any Type Of Water As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth,", "get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Crossing Puddles, Pools, Flooded Areas Or Other Standing Water Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle", "want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.  CAUTION: Muddy waters can reduce the cooling system effectiveness by depositing debris onto the radiator.  Crossing Puddles, Pools, Flooded Areas Or Other Standing Water Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.  CAUTION: Muddy waters can reduce the cooling system effectiveness by depositing debris onto the radiator.  Driving Through Water Extreme care should be", "effectiveness by depositing debris onto the radiator.  Driving Through Water Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate", "5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  CAUTION: Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water Flowing water can be extremely dangerous.  Never attempt to cross a fast running stream or river even in shallow water.  Fast", "dangerous.  Never attempt to cross a fast running stream or river even in shallow water.  Fast moving water can easily push your vehicle downstream, sweeping it out of control.  Even in very shallow water, a high current can still wash the dirt out from around your tires putting you and your vehicle in jeopardy.  There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the vehicle's running ground clearance.  You should never attempt to cross flowing water which is deeper than the vehicle's running ground clearance.  Even the slowest current can push the heaviest vehicle downstream and out of control if the water is deep enough to push on the large surface area of the vehicle's body.  Before you proceed, determine the speed of the current, the water's depth, approach angle, bottom condition and if there are any obstacles.  Then cross at an angle heading slightly upstream using the low and slow technique.  WARNING: Never drive through fast moving deep", "slightly upstream using the low and slow technique.  WARNING: Never drive through fast moving deep water.  It can push your vehicle downstream, sweeping it out of control.  This could put you and your passengers at risk of injury or drowning.  Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L", "gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  As you approach any type of water, you", "may not be covered by the New Vehicle Limited Warranty.  As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are", "an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.", "To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped)Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security", "Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.", "system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for", "the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF", "Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY", "system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be", "may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  Connected Services Send & Go FAQs \u2014 If Equipped How long does it take to send the route and destination to my vehicle?  Depending on various conditions, it can take up to three minutes for the request to get through to your vehicle.  Can I cancel a route I sent to my vehicle?  Yes, once you enter your vehicle, and start the engine, the pop-up message stating that you have a new route will appear.  There is an exit button on the pop-up that will cancel the route if selected.  Can I select a different route than the most recent one I sent to my vehicle?  Yes, once you enter the vehicle, and start the engine, the pop-up message offers a \u201cLocations\u201d option.  Once \u201cLocations\u201d is selected, you can choose from a list of recently sent destinations.  Power-Up After switching the ignition key from OFF to either the ON/RUN or ACC position, or", "Power-Up After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil", "occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy", "significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Introduction To Connected Vehicle Services One of the many benefits of your vehicle\u2019s Uconnect system is that you can now take advantage of SiriusXM Guardian\u2122 connected services.  To unlock the full potential of SiriusXM Guardian\u2122 in your vehicle, you first need to activate SiriusXM Guardian\u2122 connected services.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.", "Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Note: SiriusXM Guardian\u2122 involves the collection, transmission and use of data from your vehicle  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.", "oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.", "This is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer.  They want to know if you need assistance.  If an authorized dealer is unable to resolve the concern, you may contact FCA US LLC's Customer Assistance center.  FCA US LLC and its authorized dealers are vitally interested in your satisfaction.  We want you to be happy with our products and services.  Warranty service must be done by an authorized dealer.  We strongly recommend that you take the vehicle to an authorized dealer.  They know your vehicle the best, and are most concerned that you get prompt and high quality service.  FCA US LLC's authorized dealers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner.  This is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason", "is why you should always talk to an authorized dealer\u2019s service manager first.  If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer.  They want to know if you need assistance.  If an authorized dealer is unable to resolve the concern, you may contact FCA US LLC's Customer Assistance center.  We recommend seeing an authorized dealer for service.  An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  If the transmission cannot be reset, authorized dealer service is required.  Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us)", "with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada) symbols key if you do not read the entire owner\u2019s manual, you may miss important information.  Observe all Cautions and Warnings.  Service Manuals These comprehensive Service Manuals provide a complete working knowledge of the vehicle, system, and/or components and is written in straightforward language with illustrations, diagrams, and charts.", "Adaptive Cruise Control (ACC)/Forward Collision Warning (FCW) Sensor Protective Cover \u2014 If Equipped Your vehicle may be equipped with a protective cover that is to be used whenever the windshield is folded down in order to protect the ACC/FCW sensor.  To install the cover, refer to the following instructions: Secure the top part of the cover so that it hinges to the header.  Swing the cover down and push on it so that it covers the opening.  Check to make sure the cover is secured properly.  Note: Be sure to remove the cover before returning the windshield to the normal position.  Store the cover in the cargo area.  Your vehicle may be equipped with a protective cover that is to be used whenever the windshield is folded down in order to protect the ACC/FCW sensor.  To install the cover, refer to the following instructions: If the \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the radar sensor", "than once on every trip) without any snow, rain, mud, or other obstruction, have the radar sensor realigned at an authorized dealer.  The \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d warning will display and a chime will sound when conditions temporarily limit system performance.  Always keep the sensor clean.  Carefully wipe the sensor lens with a soft cloth.  Be cautious not to damage the sensor lens.  Do not remove any screws from the sensor.  Doing so could cause an ACC system malfunction or failure and require a sensor realignment.  If the sensor or front end of the vehicle is damaged due to a collision, see an authorized dealer for service.  Do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles.  Doing so could cause an ACC system failure or malfunction.  If the \u201cACC/FCW Unavailable Wipe Front Radar Sensor\u201d warning is active, Fixed Speed Cruise Control is still available.  The \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d warning will", "is still available.  The \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d warning will display and a chime will sound when conditions temporarily limit system performance.  This most often occurs at times of poor visibility, such as in snow or heavy rain and fog.  The ACC system may also become temporarily blinded due to obstructions, such as mud, dirt, or ice on windshield and fog on the inside of glass.  In these cases, the instrument cluster display will read \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d and the system will have degraded performance.  If the instrument cluster displays \u201cACC/FCW Limited Functionality\u201d or \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d momentarily, there may be a condition that limits FCW functionality.  Although the vehicle is still drivable under normal conditions, the active braking may not be fully available.  Once the condition that limited the system performance is no longer present, the system will return to its full performance state.  If the", "performance is no longer present, the system will return to its full performance state.  If the problem persists, see an authorized dealer.  If the system turns off, and the instrument cluster display reads \u201cACC/FCW Unavailable Service Required\u201d or \u201cCruise/FCW Unavailable Service Required\u201d, there may be an internal system fault or a temporary malfunction that limits ACC functionality.  Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.  If this occurs, try activating ACC again later, following an ignition cycle.  If the problem persists, see an authorized dealer.  This message can sometimes be displayed while driving in adverse weather conditions.  The ACC/FCW system will recover after the vehicle has left these areas.  Under rare conditions, when the camera is not tracking any vehicles or objects in its path this warning may temporarily occur.  Changing the FCW status to \u201cOnly Warning\u201d prevents the system from providing limited active braking, or additional", "status to \u201cOnly Warning\u201d prevents the system from providing limited active braking, or additional brake support if the driver is not braking adequately in the event of a potential frontal collision, but maintains the audible and visual warnings.  Changing the FCW status to \u201cOff\u201d prevents the system from providing autonomous braking, or additional brake support if the driver is not braking adequately in the event of a potential frontal collision.  The system will retain the last setting selected by the driver after ignition shut down.  FCW may not react to irrelevant objects such as overhead objects, ground reflections, objects not in the path of the vehicle, stationary objects that are far away, oncoming traffic, or leading vehicles with the same or higher rates of speed.  FCW will be disabled like ACC, with the unavailable screens.  Service ACC/FCW Warning If the system turns off, and the instrument cluster display reads \u201cACC/FCW Unavailable Service Required\u201d or \u201cCruise/FCW Unavailable Service Required\u201d,", "display reads \u201cACC/FCW Unavailable Service Required\u201d or \u201cCruise/FCW Unavailable Service Required\u201d, there may be an internal system fault or a temporary malfunction that limits ACC functionality.  Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.  If this occurs, try activating ACC again later, following an ignition cycle.  If the problem persists, see an authorized dealer.", "To Start The Engine While In Autostop Mode While in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is pressed.  The transmission will automatically re-engage upon engine restart.  To Activate The Autostop Mode, The Following Must Occur: Conditions That Will Cause The Engine To Start Automatically While In Autostop Mode: To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: Conditions that will cause the engine to start automatically while in STOP/START AUTOSTOP ACTIVE mode, the engine will start automatically when: This indicator light will illuminate when the Stop/Start function is in \u201cAutostop\u201d mode.  The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  While in an Autostop,", "other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  While in an Autostop, the Climate Control system may automatically adjust airflow to maintain cabin comfort.  Customer settings will be maintained upon return to an engine running condition.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This light alerts the driver that the vehicle is in the neutral mode  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and", "speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air", "to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  If you get hung up or high-centered on an object,", "jacking on locations other than those indicated.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.", "get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand,", "brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change", "changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.", "The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or", "large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  External racks do not increase the total load carrying capacity of the vehicle.  Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, does not exceed the maximum vehicle load capacity.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  The Roof Luggage Rack is designed to allow for carrying an", "sport bar, and body, or fully removed.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight", "roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.", "Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on", "may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Seat Belt Reminder Warning Light This warning light indicates when the driver or passenger seat belt is unbuckled.  When the ignition is first placed in the ON/RUN or ACC/ON/RUN position and if the driver\u2019s seat belt is unbuckled, a chime will sound and the light will turn on.  When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound Service 4WD Warning Light \u2014 If Equipped This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning", "If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.", "The BSM system notifies the driver of objects in the detection zones by illuminating the BSM Warning Light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume.  See \"\u21e8blind spot modes\" for further information.  The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.  The BSM system will issue an alert during these types of zone entries.  When the BSM system is turned off there will be no visual or audible alerts from either the BSM or RCP systems.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft", "12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft (3 m) beyond the rear fascia/bumper of the vehicle.  The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas.  BSM Radar Location (Left Side Shown) The BSM system will store the current operating mode when the vehicle is shut off.  Each time the vehicle is started the previously stored mode will be recalled and used.  Blind Spot Monitoring (BSM) \u2014 If Equipped The BSM system uses two radar sensors, located inside the taillights, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.)  that enter the blind spot zones from the rear/front/side of the vehicle.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate", "mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m).  The zone starts at the outside rearview mirror and extends approximately 10 ft (3 m) beyond the rear fascia/bumper of the vehicle.  The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas.  The BSM system can become blocked if snow, ice, mud, or other road contaminations accumulate on the rear fascia/bumper where the radar sensors are located.  The system may also detect a blockage if the vehicle is operated in areas with extremely low radar returns, such as a desert, or parallel to a large elevation drop.  If a blockage is detected, a \u201cBlind Spot Temporarily Unavailable, Wipe Rear Corners\u201d message will display in the instrument", "a \u201cBlind Spot Temporarily Unavailable, Wipe Rear Corners\u201d message will display in the instrument cluster, both mirror lights will illuminate, and BSM and RCP alerts will be disabled.  This is normal operation.  The system will automatically resume function when the condition clears.  To minimize system blockage, do not block the area of the rear fascia/bumper where the radar sensors are located with foreign objects (bumper stickers, bicycle racks, etc.)  and keep it clear of road contaminations.  The BSM system notifies the driver of objects in the detection zones by illuminating the BSM Warning Light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume.  See \"\u21e8blind spot modes\" for further information.  The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.  The BSM system will issue an alert during these types of zone entries.  Note: The BSM system DOES NOT alert", "system will issue an alert during these types of zone entries.  Note: The BSM system DOES NOT alert the driver about rapidly approaching vehicles that are outside the detection zones.  The BSM system detection zone DOES NOT change if your vehicle is towing a trailer.  Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change.  If the trailer or other object (i.e., bicycle, sports equipment) extends beyond the side of your vehicle, this may result in the BSM Warning Light remaining illuminated the entire time the vehicle is in a forward gear.  See \"\u21e8uconnect settings\" for more information.  The Blind Spot Monitoring (BSM) system may experience dropouts (blinking on and off) of the side mirror warning indicator lights when a motorcycle or any small object remains at the side of the vehicle for extended periods of time (more than a couple of seconds).  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center", "rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  Manual Mirror Adjustment If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror", "small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Ignoring the Rearview Mirror light could mean you will not have SOS Call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  When cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on", "mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on the mirror.", "Brake/Transmission Shift Interlock (BTSI) System This vehicle is equipped with a BTSI system that holds the transmission gear selector in PARK unless the brakes are applied.  To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.  The brake pedal must also be pressed to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is stopped or moving at low speeds.  Brake/Transmission Shift Interlock (BTSI) System This vehicle is equipped with a BTSI system that holds the transmission gear selector in PARK unless the brakes are applied.  To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.  The brake pedal must also be pressed to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is stopped or moving at low speeds.  Ignition Park Interlock This vehicle is equipped with an Ignition Park Interlock system which requires the transmission to be in PARK before the ignition can be turned to the OFF position.  This", "the transmission to be in PARK before the ignition can be turned to the OFF position.  This helps the driver avoid inadvertently leaving the vehicle without placing the transmission in PARK.  This system also locks the transmission in PARK whenever the ignition is in the OFF position.  Note: The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  AUTOMATIC TRANSMISSION \u2014 IF EQUIPPED You must press and hold the brake pedal while shifting out of PARK.  WARNING: Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure", "trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a", "a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or", "the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  CAUTION: Shift into or out of PARK or REVERSE only after the vehicle has come to a complete stop.  Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed.  Before shifting into any gear, make sure your foot is firmly pressing the brake pedal.  ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the", "cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Ignition Park Interlock This vehicle is equipped with an Ignition Park Interlock system which requires the transmission to be in PARK before the ignition can be turned to the OFF position.  This helps the driver avoid inadvertently leaving the vehicle without placing the transmission in PARK.  This system also locks the transmission in PARK whenever the ignition is in the OFF position.  Note: The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  Power-Up After switching the ignition key from OFF to either the ON/RUN or ACC position, or", "Power-Up After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press", "Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the", "km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam", "in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD", "Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button", "is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an", "SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.", "To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when", "20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set", "ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speed  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed", "show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which", "sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.", "Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect", "against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.", "vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Place the vehicle in a warm area.  Pull steadily on the top", "to leak into the vehicle's interior.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  From the Sunrider\u00ae Position, remove straps if previously secured.  Step One Failure to follow the next steps could result in damage to the soft top or vehicle.  Using the side link, lift and push the soft top toward the front of the vehicle, manually guiding the top into the closed position.  Step Two Step Two From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Step Three Pull the handle back upward while squeezing the hook, locking the latch into place.  Step Four It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's", "opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING:", "(5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional", "not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric topDo not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet", "prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Preparations For Jacking Park on a firm, level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking", "operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers should not remain in the vehicle when the vehicle is being jacked in position.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating", "not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.", "Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a", "6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition", "voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both", "it to work with Android Auto\u2122.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 \u00b9 use this qr code to access your digital experience.  While using Android Auto\u2122, Google Maps\u2122 provides voice-guided:  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.", "new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.", "cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  While using Android Auto\u2122, Google Maps\u2122 provides voice-guided: Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data", "on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Plugging in a smartphone device", "devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE", "USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into", "the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.", "Window Lockout Switch The window lockout switch allows you to disable the window controls on the rear passenger doors.  To disable the window controls, rotate the switch downward.  To enable the window controls, rotate the switch upward.  Child-Protection Door Lock System \u2014 Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove the sealing plug for access, and use a flat-blade screwdriver (or mechanical key) to rotate the dial to the lock or unlock position.  Note: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test", "it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Note: Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  Auto-Down Feature The driver door power window switch and the front passenger door power window", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.", "In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  In some localities, it", "diesel emissions standards required by the Environmental Protection Agency.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the", "driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  This vehicle is equipped with a Diesel Exhaust Fluid (DEF) injection system and a Selective Catalytic Reduction (SCR) catalyst to meet the emission requirements.  Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the", "container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light (MIL) to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these", "monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you", "test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd", "you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.", "Vehicle Identification Number Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.  Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of", "A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.  To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Before programming a device to one of your HomeLink\u00ae buttons, you must determine whether the device has a rolling code or non-rolling code.  You have 30 seconds in which to initiate rolling code final step 2, after completing rolling code final step 1.", "If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire", "will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Using the provided #T40 Torx head driver and", "fasteners.  Damage to the vehicle\u2019s parts will occur.  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque Specification For Torx Fastener Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  Damage to the retainers will occur.  Step One Install the door frames.  Start with", "Torx fasteners.  Damage to the retainers will occur.  Step One Install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step Four Using the provided #T50 Torx head driver and ratchet, install and tighten the Torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step Five Torque Specification For Torx", "torque specifications.  Repeat on the opposite side.  Step Five Torque Specification For Torx Fasteners Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Step Five Before driving the vehicle with the top in the Sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners Step Six  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the", "and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "The ACC screen may display once again if any ACC activity occurs, which may include any of the following: This feature will only activate when the following conditions are met: The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: Once SSC is enabled it will activate automatically once the following conditions are met: The following conditions must be met in order for HSA to activate:  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: If the ABS Warning", "also may experience the following normal characteristics when the ABS activates: If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN", "If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To", "by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervalsYour vehicle is equipped with dual hydraulic brake systems.  If either of the two hydraulic systems lose normal capability, the remaining system will still function.  However, there will be some loss of overall braking effectiveness.  You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.  If the driver does not take action based upon these progressive warnings, then the system will provide a limited level", "not take action based upon these progressive warnings, then the system will provide a limited level of active braking to help slow the vehicle and mitigate the potential forward collision.  If the driver reacts to the warnings by braking and the system determines that the driver intends to avoid the collision by braking but has not applied sufficient brake force, the system will compensate and provide additional brake force as required.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).", "you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user's safety or the safety of others.  Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure", "vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The ACC system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.", "To ensure proper engine lubrication, the engine oil must be maintained at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Check engine oil level Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage Check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed Check function of all interior and exterior lights  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal", "(IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel", "or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Checking Oil Level To ensure proper engine lubrication, the engine oil must be maintained at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off.  Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.  There are four possible dipstick types: Crosshatched zone.  Crosshatched zone marked SAFE.  Crosshatched zone marked with MIN at the low end of the range and MAX at the high end of the range.  Crosshatched zone marked with dimples at the MIN and the MAX ends of the range.  Adding 1 qt (1 L) of oil when the reading is at the low end of the dipstick range will raise the oil level to the high end of the range marking.  Note: Always maintain the oil level within the crosshatch", "to the high end of the range marking.  Note: Always maintain the oil level within the crosshatch markings on the dipstick.  CAUTION: Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure.  This could damage your engine.  Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not", "as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.", "STOP/START SYSTEM \u2014 AUTOMATIC TRANSMISSION (IF EQUIPPED) The Engine Stop/Start (ESS) function is developed to reduce fuel consumption.  The system will stop the engine automatically during a vehicle stop if the required conditions are met.  Releasing the brake pedal or pressing the accelerator pedal will automatically restart the engine.  ESS vehicles have been upgraded with a heavy-duty starter, enhanced battery, and other upgraded engine parts, to handle the additional engine starts.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  STOP/START SYSTEM \u2014 MANUAL TRANSMISSION (IF EQUIPPED) The Engine Stop/Start (ESS) function is developed to reduce fuel consumption.  The system will stop the engine automatically during a vehicle stop if the required conditions are met.  Pressing the clutch pedal will automatically restart the vehicle.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  Electronic Stability Control (ESC) Active Warning Light", "system be disabled during off-road use.  Electronic Stability Control (ESC) Active Warning Light \u2014 If Equipped This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the", "The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.", "FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your", "in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you", "That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning:", "holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Natural Speech Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Natural speech allows the user to speak commands in phrases or complete sentences.  The system filters out certain non-word utterances and sounds such as \u201cah\u201d and \u201ceh.\u201d The system handles fill-in words such as \u201cI would like to\u201d.  The system handles multiple inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you", "identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you want to call?\u201d in the case where a phone call was requested but the specific name was not recognized.  The system utilizes continuous dialog.  When the system requires more information from the user, it will ask a question to which the user can respond without pushing the Voice Command button on the steering wheel.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two", "its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few", "works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly", "noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general", "structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: The following basic Voice Commands can be given at any point while using your Uconnect system.  Uconnect Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  Uconnect Phone is a voice-activated, hands-free, in-vehicle communications system.  It allows you to dial a phone number with your mobile phone.  Uconnect Phone will automatically connect to the highest priority paired phone and/or Audio Device within range.  If you need to choose a particular phone or audio device follow these steps: uconnect can announce incoming text messages.  Push the vr button or phone button and say: the phone feature is driven through your bluetooth\u00ae \u201chands-free profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables", "profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.", "Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  Engine start-up in very low ambient temperature", "time.  Wait 10 to 15 seconds before trying again.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant", "a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.", "To Turn On The Engine Using The ENGINE START/STOP Button The transmission must be in PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage automatically after 10 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for serviceIn unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should", "engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined", "Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to", "cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: The message will stay active until the ignition is placed in the ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to", "(instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  To insert an Auxiliary device, gently insert the Auxiliary device cable into the AUX port.  If you insert an Auxiliary device with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system will automatically time out", "on, the unit will switch to AUX Mode and begin to play.  The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.", "Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  Manual Mirror Adjustment If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an", "located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Ignoring the Rearview Mirror light could mean you will not have SOS Call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer", "of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  When cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on the mirror.  Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.  Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.  Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror.  The Outside Mirrors are located on the front driver and passenger side doors, and are adjusted manually or by power adjustment (if", "on the front driver and passenger side doors, and are adjusted manually or by power adjustment (if equipped).  If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.", "VEHICLE IDENTIFICATION NUMBER (VIN) The VIN is found on the left front corner of the A-pillar, visible from outside of the vehicle through the windshield.  Note: It is illegal to remove or alter the VIN plate.  Vehicle Identification Number Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.  Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle", "driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.", "BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load", "cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails,", "in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  Lower Anchors And Tethers For CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are", "seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in", "slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.", "It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is", "may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a", "to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or", "or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201dWARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including", "if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.", "come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with", "in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Potential signs of vehicle overheating: Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs,", "operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine", "brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear", "until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions:", "and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the", "with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Brake System Warning Light The red Brake System Warning Light", "Flashers may wear down your battery.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.", "Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When", "if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The", "of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the", "up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax", "etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak", "Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "Off-Road Driving Tips  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels,", "in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover", "is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good", "no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over", "ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries", "could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur", "including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.", "Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune", "gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  Methylcyclopentadienyl Manganese Tricarbonyl (MMT) In Gasoline MMT is a manganese-containing metallic additive that is blended into some", "(MMT) In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasolines to increase octane.  Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT.  Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles.  The manufacturer recommends that gasoline without MMT be used in your vehicle.  The MMT content of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gasoline retailer whether the gasoline contains MMT.  MMT is prohibited in Federal law and California reformulated gasoline.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing", "and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system", "Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains", "of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.", "Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special", "paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you", "holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high", "have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.  Protection From", "by these type of products may not be covered by your New Vehicle Limited Warranty.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.", "ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are", "in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes:  ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  To Turn Off", "to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC positionIf the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF", "pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.", "For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM", "reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost", "engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.", "Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids", "Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with", "for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine", "requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a", "conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3", "Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of", "(DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  Open the fuel filler door.  Fuel Filler Door Remove the diesel fuel filler cap by rotating it counterclockwise.  Fuel and Diesel Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the vehicle with fuel.  When the nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel filler door.", "Drivetrain The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  The following information is displayed: steering angle in degrees status of transfer case status of front axles \u2014 if equipped status of the rear axles \u2014 if equipped front and rear axle lock indicator light \u2014 if equipped this light indicates when the front, rear, or both axles have been locked.  The telltale will display the lock icon on the front and rear axles to indicate the current lock status.  Drivetrain Front Wheel Angle: displays the graphical and numerical value of calculated average front wheel angle from the steering wheel orientation.  Transfer Case Lock Status: displays \u201cLock\u201d graphic only during 4WD High, 4WD Auto, or 4WD Low status.  Axle Lock And Sway Bar Status (if equipped): displays front and rear or rear only axle locker graphic, and sway bar connection graphic with text message (connected or disconnected).  Drivetrain The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  The", "Drivetrain The Drivetrain page displays information concerning the vehicle\u2019s drivetrain.  The following information is displayed: steering angle in degrees status of transfer case status of front axles \u2014 if equipped status of the rear axles \u2014 if equipped drivetrain front wheel angle: displays the graphical and numerical value of calculated average front wheel angle from the steering wheel orientation.  Transfer Case Lock Status: displays \u201cLock\u201d graphic only during 4WD High, 4WD Auto, or 4WD Low status.  Axle Lock And Sway Bar Status (if equipped): displays front and rear or rear only axle locker graphic, and sway bar connection graphic with text message (connected or disconnected).  Steering angle in degrees Status of Transfer Case Status of Front Axles \u2014 If Equipped Status of the Rear Axles \u2014 If Equipped 1 \u2014 Steering Angle 2 \u2014 Lock Icon 3 \u2014 Sway Bar 4 \u2014 Front Axle Locker Status 5 \u2014 Rear Axle Locker Status This light indicates when the front, rear, or both axles have been locked.  The telltale will display", "light indicates when the front, rear, or both axles have been locked.  The telltale will display the lock icon on the front and rear axles to indicate the current lock status.", "US/CANADA Exposure to Radio Frequency Radiation The radiated output power of the internal wireless radio is far below the FCC and IC radio frequency exposure limits.  Nevertheless, the wireless radio will be used in such a manner that the radio is 8 inches (20 cm) or further from the human body.  The internal wireless radio operates within guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community.  The radio manufacturer believes the internal wireless radio is safe for use by consumers.  The level of energy emitted is far less than the electromagnetic energy emitted by wireless devices such as mobile phones.  However, the use of wireless radios may be restricted in some situations or environments, such as aboard airplanes.  If you are unsure of restrictions, you are encouraged to ask for authorization before turning on the wireless radio \"\u21e8general information\" .  Rolling Code Devices To determine if your device has a rolling code, a good", "information\" .  Rolling Code Devices To determine if your device has a rolling code, a good indicator is its manufacturing date.  Typically, devices manufactured after 1995 have rolling codes.  A device with a rolling code will also have a \u201cLEARN\u201d or \u201cTRAIN\u201d button located where the antenna is attached to the device.  The button may not be immediately visible when looking at the device.  The name and color of the button may vary slightly by manufacturer.  Note: The \u201cLEARN\u201d or \u201cTRAIN\u201d button is not the button you normally use to operate the device.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with", "Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners", "features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a", "for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob", "systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.  Stationary Objects And Vehicles ACC does not react to stationary objects or vehicles.  For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane.  It will consider this stopped vehicle a stationary object as it did not previously detect movement from it.  Always be attentive and ready to apply the brakes if necessary.  Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.", "There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Prior to off-road usage, the side steps should be removed to prevent damage.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in", "Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  There are", "assemblies in the soft top rear window storage bag (if equipped), or a safe location.  There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  To reinstall the door(s), perform the previous steps in the reverse order.  Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is", "for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  Prior to off-road usage, the side steps should be removed to prevent damage.  Side Step Removal \u2014 If Equipped There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener locations (one side) remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside nuts after all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road", "to the underbody.  Repeat the reassembly procedure for the other side.  Note: Prior to off-road usage, the side steps should be removed to prevent damage.", "Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15,", "r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure", "load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire full size spare \u2014 if equipped the full size spare is for temporary emergency use only.  This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not.  This spare tire may have limited tread life.  When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced.  Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity.  Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and", "Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.", "The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Locking Storage Bin (Closed View) Locking Storage Bin  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be", "bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  Locking Storage Bin  Rear Wall Storage Bin The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  If equipped, the Locking Storage Bin is located below the rear", "fastener bin below the rear seat.  If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.", "Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the", "experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Fully lower the soft top to the Sunrider\u00ae positionFailure to follow the next steps could result in damage to the soft top or vehicle.  Using the provided #T50 Torx head driver and ratchet, unscrew the two Torx head fasteners on the inside of each top mechanism.  Step Two Utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle\u2019s sport bar and trim.  Store the soft top in a safe, clean, and dry location.  Remove the door frames.  The rear door frames must be removed before the front door framesUsing the provided #T50 Torx head driver and ratchet, unscrew the six Torx head fasteners on both rear corners and the back of the cab, then", "and ratchet, unscrew the six Torx head fasteners on both rear corners and the back of the cab, then remove the belt rail.  Folding down the rear seats is recommended to provide easier access to the fasteners.  Step Five 1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top", "cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.", "To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note:", "(NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Note: depending on the vehicle\u2019s options, feature settings may vary.  Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and", "Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the", "ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC positionIf the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will", "the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will", "transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If", "if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.", "may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or", "will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the", "when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the", "with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It", "a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel", "is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d,", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the", "driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will", "Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering", "pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the", "and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow", "Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.  The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window", "switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  Power Window Switches Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to", "for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as", "the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is", "up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "Draining Fuel/Water Separator Filter \u2014 Diesel Engine The fuel/water separator housing is located inside the left frame rail in front of the fuel tank.  The best access to this water drain valve is from under the vehicle.  If necessary remove the fuel filter protective cover to access the water drain valve.  If water is detected in the water separator while the engine is running, or while the ignition switch is in the ON position, the Water In Fuel Indicator Light will illuminate and an audible chime will be heard.  At this point you should stop the engine and drain the water from the filter housing.  Within 10 minutes of vehicle shutdown, turn the filter drain valve (located on the bottom of the filter housing) counterclockwise to drain fuel/water; allow the accumulated water to drain.  Leave the drain valve open until all water and contaminants have been removed.  When clear fuel is visible, close the drain valve by turning it clockwise.  Upon proper draining of the water from fuel filter assembly, the", "valve by turning it clockwise.  Upon proper draining of the water from fuel filter assembly, the Water In Fuel Indicator Light will remain illuminated for approximately 10 seconds.  If the water was drained while the engine was running, the Water In Fuel Indicator Light may remain on for approximately three minutes.  If more than two ounces or 60 ml of fuel have been drained, follow the directions for Priming If The Engine Has Run Out Of Fuel CAUTION: Do not drain the fuel/water separator filter when the engine is running.  Diesel fuel will damage blacktop paving surfaces.  Drain the filter into an appropriate container.  Note: Care should be taken in disposing of used fluids from your vehicle.  Used fluids, indiscriminately discarded, can present a problem to the environment.  Contact an authorized dealer, service station, or government agency for advice on recycling programs and for where used fluids and filters can be properly disposed of in your area.  Draining Fuel/Water Separator Filter \u2014 Diesel Engine", "can be properly disposed of in your area.  Draining Fuel/Water Separator Filter \u2014 Diesel Engine The fuel/water separator housing is located inside the left frame rail in front of the fuel tank.  The best access to this water drain valve is from under the vehicle.  If necessary remove the fuel filter protective cover to access the water drain valve.  If water is detected in the water separator while the engine is running, or while the ignition switch is in the ON position, the Water In Fuel Indicator Light will illuminate and an audible chime will be heard.  At this point you should stop the engine and drain the water from the filter housing.  Within 10 minutes of vehicle shutdown, turn the filter drain valve (located on the bottom of the filter housing) counterclockwise to drain fuel/water; allow the accumulated water to drain.  Leave the drain valve open until all water and contaminants have been removed.  When clear fuel is visible, close the drain valve by turning it clockwise.  Upon proper draining of", "When clear fuel is visible, close the drain valve by turning it clockwise.  Upon proper draining of the water from fuel filter assembly, the Water In Fuel Indicator Light will remain illuminated for approximately 10 seconds.  If the water was drained while the engine was running, the Water In Fuel Indicator Light may remain on for approximately three minutes.  If more than two ounces or 60 ml of fuel have been drained, follow the directions for Priming If The Engine Has Run Out Of Fuel CAUTION: Do not drain the fuel/water separator filter when the engine is running.  Diesel fuel will damage blacktop paving surfaces.  Drain the filter into an appropriate container.  Note: Care should be taken in disposing of used fluids from your vehicle.  Used fluids, indiscriminately discarded, can present a problem to the environment.  Contact an authorized dealer, service station, or government agency for advice on recycling programs and for where used fluids and filters can be properly disposed of in your area.  Fuel", "programs and for where used fluids and filters can be properly disposed of in your area.  Fuel Filter Replacement \u2014 Diesel Engine Ensure engine is turned off.  Remove the fuel filter protective cover to access the fuel filter assembly.  Fuel filter assembly 1 \u2014 retainers 2 \u2014 fuel filter protective cover place drain pan under the fuel filter assembly.  Open the water drain valve, and let any accumulated water and fuel drain.  Close the water drain valve.  Fuel filter assembly 1 \u2014 water drain valve wipe clean the underside of the filter housing to prevent contamination from entering fuel system during service.  Remove the fuel filter cap and filter from the housing using a socket.  Rotate counterclockwise for removal.  Fuel filter assembly 1 \u2014 fuel filter cap 2 \u2014 socket adapter remove the used fuel filter cartridge from the cap and dispose of according to your local regulations.  Wipe clean the sealing surfaces of the cap and housing.  Caution: take care when handling the new fuel filter to prevent", "surfaces of the cap and housing.  Caution: take care when handling the new fuel filter to prevent contamination from entering the fuel system.  Lubricate o-ring on the cap with clean engine oil.  Install the new fuel filter cartridge onto the cap.  Insert the cap and filter into the housing with clockwise rotation, use a socket to tighten.  After engine start, verify the fuel filter cap does not leak.  Note: Using a fuel filter that does not meet FCA US LLC filtration and water separating requirements can severely impact fuel system life and reliability.  CAUTION: Diesel fuel will damage blacktop paving surfaces.  Drain the filter into an appropriate container.  Do not prefill the fuel filter when installing a new fuel filter.  There is a possibility debris could be introduced into the fuel filter during this action.  It is best to install the filter dry and allow the in-tank lift pump to prime the fuel system.  Fuel/Water Separator Filter Do not drain the fuel/water separator filter when the engine is", "Fuel/Water Separator Filter Do not drain the fuel/water separator filter when the engine is running.  Diesel fuel will damage blacktop paving surfaces.  Drain the filter into an appropriate container.  If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage", "Volume & On/Off Control Push the VOLUME & On/Off control knob to turn on and off the Uconnect system.  The electronic volume control turns continuously (360 degrees) in either direction, without stopping.  Turning the VOLUME & On/Off control knob clockwise increases the volume, and counterclockwise decreases it.  When the audio system is turned on, the sound will be set at the same volume level as last played.  Steering Wheel Audio Controls The remote sound system controls are located on the rear surface of the steering wheel at the three and nine o\u2019clock positions.  The right-hand control is a rocker-type switch with a push button in the center and controls the volume and mode of the sound system.  Pushing the top of the rocker switch will increase the volume, and pushing the bottom of the rocker switch will decrease the volume.  Pushing the right-hand control\u2019s center button will make the radio switch between the various modes available (AM/FM/SXM or Media, etc.).  The left-hand control is a rocker-type", "the various modes available (AM/FM/SXM or Media, etc.).  The left-hand control is a rocker-type switch with a push button in the center.  The function of the left-hand control is different depending on which mode you are in.  The following describes the left-hand control operation in each mode:  Adjustable Chime Volume Settings The Front and Rear chime volume settings are programmable.  The settings may be programmed through the Uconnect systemThe chime volume settings include low, medium, and high.  The factory default volume setting is medium.  ParkSense will retain its last known configuration state through ignition cycles.", "Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure", "30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are", "pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  See the following steps for refueling: The vehicle may be equipped with a", "serious injury or death.  See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose", "the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.", "and power steering, and fill as needed.  Check function of all interior and exterior lights.  AUTOMATIC TRANSMISSION \u2014 IF EQUIPPED You must press and hold the brake pedal while shifting out of PARK.  WARNING: Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to", "and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock", "always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  CAUTION: Shift into or out of PARK or REVERSE only after the vehicle has come to a complete stop.  Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed.  Before shifting into any gear, make sure your foot is firmly pressing the brake pedal.  PARK (P) This range supplements the parking brake by locking the", "firmly pressing the brake pedal.  PARK (P) This range supplements the parking brake by locking the transmission.  The engine can be started in this range.  Never attempt to use PARK while the vehicle is in motion.  Apply the parking brake when exiting the vehicle in this range.  When parking on a hill, apply the parking brake before shifting the transmission to PARK.  As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  When exiting the vehicle, always: apply the parking brake shift the transmission into park turn the ignition off remove the key fob from the vehicle the following indicators should be used to ensure that you have properly engaged the transmission into the park position: when shifting into park, push the lock button on the gear selector and firmly move the gear selector all the way forward until it stops and is fully seated.  Look at the transmission gear position display and verify that it indicates the PARK position", "Look at the transmission gear position display and verify that it indicates the PARK position (P), and is not blinking.  With the brake pedal released, verify that the gear selector will not move out of PARK.  Note: On four-wheel drive vehicles, be sure that the transfer case is in a drive position.  WARNING: Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely", "indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the", "transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  CAUTION: Before moving the transmission gear selector out of PARK, you must start the engine, and also press the brake pedal.  Otherwise, damage to the gear selector could result.  DO NOT race the engine when shifting from PARK or NEUTRAL", "to the gear selector could result.  DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain.", "Door Frame Installation Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten fasteners target torque specification for torx fasteners maximum minimum 44.2 in-lb (5 n\u00b7m) 53.1 in-lb (6 n\u00b7m) 35.4 in-lb (4 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of", "door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step five step five insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  To remove the half-doors, repeat the installation steps in reverse order.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to", "from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate", "not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  If the check arm is stuck inside the door, follow these instructions to install the check arm.  To reinstall the door(s), perform the previous steps in the reverse order.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  To install the front door exterior mirrors on the half-doors, proceed as follows: To install the front or rear half-doors, proceed as follows: Locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place Tool Into Service Hole Of Plug To Remove Using the tool, slowly pull upwards from the center of the plug to remove.  Upon first", "To Remove Using the tool, slowly pull upwards from the center of the plug to remove.  Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  Only adjust the door to fit correctly against the striker.  DO NOT adjust the striker, as this could affect the positioning of the full door.  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.", "door frame.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door", "Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The rear door frames must be removed first, followed by the front door frames.  Loosen (do not remove) the four bolts on the door hinges", "first, followed by the front door frames.  Loosen (do not remove) the four bolts on the door hinges using the provided #T50 Torx head driver.  Hinge Bolt Locations Do not adjust the body mounted hinges, or any part of the door latch, as modifications to these parts will affect installation of the full door.  With the bolts loose, the door can be moved forward by pushing the door handle toward the front of the vehicle, and/or upward by grabbing the door handle and lifting towards the roof.  Once the gaps between the door and vehicle body are uniform around the entire door, tighten the door hinge bolts to 20.3 ft\u00b7 lb / 27.5 N\u00b7m (Max Torque: 27.3 ft\u00b7 lb / 37 N\u00b7m).  Lift upward on each section of the seat bottom.  Lift From Beneath Seat (Left Side Shown) Raise the seat bottom upward into the Stadium Position.  Stadium Position If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top If your vehicle is equipped with a soft top, the top must be lowered", "installation of the hard top If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Determine which door is affected.  Open the affected door and hold a dollar-size piece of paper along the top of the door opening against the vehicle near where the leak/noise was observed.  Make sure half of the paper is above the area where the door seal contacts the door opening, while the other half is below.  Close the door on the paper, then pull the paper upward.  If the paper moves with little to no effort, the upper half-door will need to be adjusted in that area to increase seal compression.  Performing A Paper Test Push Upward On Middle Of Upper Half Door To Remove", "The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended: A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  A long break-in period is not required for the engine and drivetrain (transmission and axle) in", "A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.", "recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which", "type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.", "Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain", "Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  CAUTION: If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage", "On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the", "seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not", "shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Press and release this button to turn the Climate Control ON/OFF.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  To Turn Off The Engine Using The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control will turn off, but Stability Control will remain active.  Hold the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC", "the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to", "turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the", "(A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine", "normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the", "ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.", "Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam", "the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.  Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Automatic Dimming Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  This mirror automatically adjusts for", "be adjusted to center on the view through the rear window.  This mirror automatically adjusts for headlight glare from vehicles behind you.  The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Note: The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  Automatic High Beam Headlamp Control \u2014 If Equipped The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automatically controlling the high beams through the use of a camera mounted on the vehicle\u2019s header.  This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.  Note: the automatic high beam headlamp control can be turned on or", "vehicle is out of view.  Note: the automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.", "Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Important Safety Precautions Please", "the seat belt, which could result in serious injury or death.  Important Safety Precautions Please pay close attention to the information in this section.  It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.  Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: Children 12 years old and under should always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint Never allow children to slide the shoulder belt behind them or under their arm.  You should read the instructions provided with your child restraint to make sure that you are using it", "should read the instructions provided with your child restraint to make sure that you are using it properly.  All occupants should always wear their lap and shoulder belts properly.  The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate.  Do not lean against the door or window.  If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.  If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see \"\u21e8if you need assistance\" for customer service contact information.  WARNING: Never place a rear-facing child restraint in front of an air bag.  A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.  Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing", "Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing child restraint in the rear seat.  If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle.  Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  The front passenger seat", "the desired position is reached and the seatback will lock into place.  The front passenger seat is unoccupied or has very light objects in it.  The front passenger seat is occupied by a rear-facing child restraint.  The front passenger seat is occupied by a child, including a child seated in a forward-facing child restraint or booster seat.  The front passenger seat is occupied by a small passenger, including a child or small adult.  The front passenger is not properly seated or his or her weight is taken off of the seat for a period of time.  Turn off the vehicle and have the adult passenger step out of the vehicle.  Remove any extra materials from the passenger seat, such as cushions, pads, seat covers, seat massagers, blankets, extra clothing, etc.  Place the seatback in the full upright position.  Have the adult passenger sit in the center of the seat, with the passenger\u2019s feet comfortably on or near the floor, and with their back against the seatback.  Restart the vehicle and have the passenger remain", "floor, and with their back against the seatback.  Restart the vehicle and have the passenger remain in this seated position for two to three minutes after restarting the vehicle.  The outboard front passenger seat BeltAlert is not active when the outboard front passenger seat is unoccupied.  BeltAlert may be triggered when an animal or other items are placed on the outboard front passenger seat or when the seat is folded flat (if equipped).  It is recommended that pets be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts, and cargo is properly stowed.  The 60/40 Split Folding Rear Seat can be folded flat to access the storage area behind the seat.  The seat bottom can also be lifted into the Stadium Position to create more storage space on the rear floor, and provide access to the underseat storage bins (if equipped) Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not", "locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  Be certain that the seatback is securely locked into position.  Perform a \u201cpush - pull - push\u201d check to confirm the seat is fully locked.  If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers.  A red indicator on the pull strap will be displayed if the seatback is not securely locked.  An improperly latched seat could cause serious injury.", "The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be", "rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds,", "your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional", "vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.", "JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in", "pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical", "in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the", "connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these", "in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.  Note: Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle while making connections.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack,", "alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two", "Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and", "Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have", "discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.", "Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset", "section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start", "The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will", "Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.", "If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used", "the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered", "fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank", "escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light", "cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's", "do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see \"\u21e8draining fuel/water separator filter \u2014 diesel engine\" .", "See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a", "See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the", "Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can", "lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  To Reset The Manual Park Release: Pull upward on the tether strap, releasing it from the \u201clocked\u201d position.  Lower the Manual Park Release lever downward into its original position.  Original tether position tuck the tether strap into the base of the", "into its original position.  Original tether position tuck the tether strap into the base of the console, and reinstall the cover.  Extended Park Starting Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Note: Extended Park condition occurs when the vehicle has not been started or driven for at least 30 days.  CAUTION: To prevent damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.", "Automatic Operation Push the AUTO button on the faceplate, or the AUTO button on the touchscreen on the Automatic Temperature Control (ATC) Panel.  Next, adjust the temperature that you would like the system to maintain by adjusting the driver and passenger temperature control buttons.  Once the desired temperature is displayed, the system will achieve and automatically maintain that comfort level.  When the system is set up for your comfort level, it is not necessary to change the settings.  You will experience the greatest efficiency by simply allowing the system to function automatically.  To provide you with maximum comfort in the Automatic mode during cold start-ups, the blower fan will remain on low until the engine warms up.  The blower will increase in speed and transition into Auto mode.  Note: It is not necessary to move the temperature settings for cold or hot vehicles.  The system automatically adjusts the temperature, mode, and blower speed to provide comfort as quickly as possible.  The", "adjusts the temperature, mode, and blower speed to provide comfort as quickly as possible.  The temperature can be displayed in U.S. Or metric units by selecting the u.s./metric customer-programmable feature within uconnect settings \"\u21e8uconnect settings\" .  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Weather control settings hot weather and vehicle interior is very hot set the mode control to (panel mode), (max a/c) on, and blower on high.  Roll down the windows for a minute to flush out the hot air.  Adjust the controls as needed to achieve comfort.  Warm weather turn (a/c) on and set the mode control to (panel mode).  Cool sunny operate in (bi-level mode).  Cool & humid conditions set the mode control to (mix mode) and turn on (a/c) to keep windows clear.  Cold weather set the mode control to (floor mode).  If windshield fogging starts to occur,", "clear.  Cold weather set the mode control to (floor mode).  If windshield fogging starts to occur, move the control to (mix mode).  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is", "an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid", "could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.", "Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard Top Panel(s) Storage Bag \u2014", "that are used when the hard top is not installed on the vehicle.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top", "the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or", "vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure", "the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the", "in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric", "with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.", "This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  This warning light indicates the Electronic Stability Control (ESC) is off.  The ESC OFF Indicator Light indicates that the Electronic Stability Control (ESC) is in a reduced mode.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.", "is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  The behavior of Electronic Stability Control while in Off Road+ varies depending on the 4WD status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also, holding the ESC OFF button for five seconds will turn off ESC.  In 4WD Low, Electronic Stability Control automatically shuts off regardless of the Off Road Status.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be", "the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not attempt to drive the vehicle over 18 mph (29 km/h).  Driving faster than 18 mph (29 km/h) with a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  The ESC Activation/Malfunction Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN mode.  It should go out with the engine running.  If the ESC Activation/Malfunction Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  This warning light will turn on when there's a fault with the EPS system  Electronic Stability Control (ESC) Active", "will turn on when there's a fault with the EPS system  Electronic Stability Control (ESC) Active Warning Light \u2014 If Equipped This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is", "position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.  Monitoring battery level status led light red 40% or lower yellow 40% to 70% green 70% to 100% electronic stability control (esc) active warning light \u2014 if equipped this warning light will indicate when the electronic stability control system is active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem", "greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.  Adaptive Cruise Control (ACC) Set Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.", "Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an", "information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system", "personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL", "your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.", "ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System.  This feature is a communication network that takes effect in the event of an impact \"\u21e8enhanced accident response system\" .  ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System.  This feature is a communication network that takes effect in the event of an impact Enhanced accident response system in the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the occupant restraint controller (orc) will determine whether to have the enhanced accident response system perform the following functions: cut off fuel to the engine (if equipped) cut off battery power to the electric motor (if equipped) flash hazard lights as long as the battery has power turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the", "which remain on as long as the battery has power or for 15 minutes from the intervention of the enhanced accident response system unlock the power door locks your vehicle may also be designed to perform any of these other functions in response to the enhanced accident response system: turn off the fuel filter heater, turn off the hvac blower motor, close the hvac circulation door cut off battery power to the: engine electric motor (if equipped) electric power steering brake booster electric park brake automatic transmission gear selector horn front wiper note: after an accident, remember to cycle the ignition to the stop (off/lock) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset", "fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.  Automatic SOS \u2014 If Equipped Automatic SOS is a hands-free safety service that can immediately connect you with help in the event that your vehicle\u2019s airbags deploy.  Please refer to your provided radio", "you with help in the event that your vehicle\u2019s airbags deploy.  Please refer to your provided radio supplement for complete information.", "The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.", "driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  Off-Road Driving Tips  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of", "You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and", "too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the", "setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic mode \"\u21e8automatic operation\" .  A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected,", "increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  To Deactivate A soft tap on the brake pedal, pushing the CANC (cancel) button, or normal brake pressure while slowing the vehicle will deactivate the Cruise Control without erasing the set speed from memory.  The following conditions will also deactivate the cruise control without erasing the set speed from memory: vehicle parking brake is applied stability event occurs gear selector is moved out of drive engine overspeed occurs clutch pedal is pressed (manual transmission only) vehicle is operating at a low rpm (manual transmission only) pushing the on/off button or placing the ignition in the off position, erases the set speed from memory.  Recirculation Button Push the Recirculation button on the faceplate", "the set speed from memory.  Recirculation Button Push the Recirculation button on the faceplate to change the system between recirculation mode and outside air mode.  The Recirculation indicator and the A/C indicator (if equipped) illuminate when the Recirculation button is pressed.  Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.  Recirculation can be used in all modes except for Defrost.  Recirculation may be unavailable if conditions exist that could create fogging on the inside of the windshield.  The A/C can be deselected manually without disturbing the mode control selection.  Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur.  Extended use of this mode is not recommended.  On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode to improve window clearing operation.  Recirculation is disabled automatically if this mode is selected.  Attempting to use", "operation.  Recirculation is disabled automatically if this mode is selected.  Attempting to use Recirculation while in this mode causes the LED on the control button to blink and then turn off.", "FOLDING WINDSHIELD The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element provides.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded", "belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  WARNING: Carefully follow these warnings to help protect against personal injury: Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raising The Windshield Release the strap that secured the windshield in the", "cause personal injury.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshieldUsing the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Cleaning Instructions During", "make sure the windshield is raised prior to installing the tops.  Cleaning Instructions During windshield down applications, dust/dirt can accumulate in the cover and block the camera lens.  Use a microfiber cloth to clean the camera lens, module, and inside cover, being careful not to damage or scratch the module.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a", "driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will", "longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may", "and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.", "Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Console Storage Compartment The center console has both an upper and lower", "the floor are removed.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by", "Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as", "The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.", "Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d The buttons on the right side of the steering wheel operate the ACC system.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged ACC Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following appears in the instrument cluster display:  To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.", "To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d WARNING: Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous.  You could accidentally set the system or cause it to go faster than you want.  You could lose control and have a collision.  Always leave the system off when you are not using it.  Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.", "Intermittent Wipers Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.  Rotate the end of the lever to the first detent position for one of four intermittent settings.  The delay cycle can be set anywhere between 1 to 18 seconds.  Note: The wiper delay times depend on vehicle speed.  If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled.  Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.  Rotate the end of the lever to the first detent position for one of four intermittent settings.  The delay cycle can be set anywhere between 1 to 18 seconds.  Intermittent Wipers Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  Windshield Washers To use the", "past the intermittent settings for high-speed wiper operation.  Windshield Washers To use the washer, pull the lever toward you and hold until desired spray is reached.  If the lever is pulled while in the delay range, the wiper will start and continue to operate for two or three wipe cycles after the lever is released.  Then, the intermittent interval previously selected will resume.  If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles.  Then, the wipers will turn off.  Note: As a protective measure, the washer will stop if the switch is held for more than 20 seconds.  Once the switch is released the washer will resume normal operation.  WARNING: Sudden loss of visibility through the windshield could lead to a collision.  You might not see other vehicles or other obstacles.  To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.", "Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an", "information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system", "personal information.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL", "your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.", "What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the", "start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from", "with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery", "disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Battery Saver On, Battery Saver Mode Message, And Electrical Load Reduction Actions (If Equipped) This vehicle is equipped with an Intelligent Battery Sensor (IBS) to perform additional monitoring of the electrical system and status of the vehicle battery.  In cases when the IBS detects charging system failure, or the vehicle battery conditions are deteriorating, electrical load reduction actions will take place to extend the driving time and distance of the vehicle.  This is done by reducing power to or turning off non-essential electrical loads.  Load reduction is only active when the engine is running.  It will display a message if there is a risk of battery depletion to the point where the vehicle may stall due to lack of electrical supply, or will not restart after the current drive", "the vehicle may stall due to lack of electrical supply, or will not restart after the current drive cycle.  When load reduction is activated, the message \u201cBattery Saver On Some Systems May Have Reduced Power\u201d will appear in the instrument cluster.  These messages indicate the vehicle battery has a low state of charge and continues to lose electrical charge at a rate that the charging system cannot sustain.  The electrical loads that may be switched off (if equipped), and vehicle functions which can be affected by load reduction: heated seat/vented seats/heated wheel rear defroster and heated mirrors hvac system 115 volt ac power inverter system audio and telematics system loss of battery charge may indicate one or more of the following conditions: the charging system cannot deliver enough electrical power to the vehicle system because the electrical loads are larger than the capability of the charging system.  The charging system is still functioning properly.  Turning on all possible vehicle electrical", "The charging system is still functioning properly.  Turning on all possible vehicle electrical loads (e.g.  HVAC to max settings, exterior and interior lights, overloaded power outlets +12 Volt, 115 Volt AC, USB ports) during certain driving conditions (city driving, towing, frequent stopping).  Installing options like additional lights, upfitter electrical accessories, audio systems, alarms and similar devices.  Unusual driving cycles (short trips separated by long parking periods).  The vehicle was parked for an extended period of time (weeks, months).  The battery was recently replaced and was not charged completely.  The battery was discharged by an electrical load left on when the vehicle was parked.  The battery was used for an extended period with the engine not running to supply radio, lights, chargers, +12 Volt portable appliances like vacuum cleaners, game consoles and similar devices.  Note: The charging system is independent from load reduction.  The charging system performs a diagnostic on the", "system is independent from load reduction.  The charging system performs a diagnostic on the charging system continuously.  If the battery charge warning light is on it may indicate a problem with the charging system \"\u21e8battery charge warning light\" .", "Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To", "floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.  Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten", "the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.", "To engage REVERSE gear from the NEUTRAL position, lift the REVERSE ring, located below the knob and move the gear selector all the way left and then forward.  If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  To shift the gears, fully press the clutch pedal and place the gear selector into the desired gear position (the diagram for the engagement of the gears is displayed on the handle of the selector).  The gear position will be displayed in the instrument cluster.  Operation To activate AutoStick mode, move the gear selector into the MANUAL (M) position (beside the DRIVE position).  The current transmission gear will be displayed in the instrument cluster.  In AutoStick mode,", "The current transmission gear will be displayed in the instrument cluster.  In AutoStick mode, you can use the gear selector (in the MANUAL position) to manually shift the transmission.  Tapping the gear selector forward (-) while in the MANUAL (M) position will downshift the transmission to the next lower gear.  Tapping the selector rearward (+) will command an upshift.  In AutoStick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result.  It will remain in the selected gear until another upshift or downshift is chosen, except as follows: The transmission will automatically downshift as the vehicle slows (to prevent engine lugging) and will display the current gear.  The transmission will automatically downshift to FIRST gear when coming to a stop.  After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or", "as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or THIRD gear, in 4L range).  Tapping (+) (at a stop) will allow starting in SECOND gear.  Starting out in SECOND or THIRD gear can be helpful in snowy or icy conditions.  If a requested downshift would cause the engine to overspeed, that shift will not occur.  The system will ignore attempts to upshift at too low of a vehicle speed.  Holding the gear selector in the (-) position will downshift the transmission to the lowest gear possible at the current speed.  Transmission shifting will be more noticeable when AutoStick is enabled.  The system may revert to automatic shift mode if a fault or overheat condition is detected.  To disengage AutoStick mode, return the gear selector to the DRIVE position.  You can shift in or out of the AutoStick position at any time without taking your foot off the accelerator pedal.  Note: When Hill Descent Control is enabled, AutoStick is not active.  WARNING: Do not downshift for", "Note: When Hill Descent Control is enabled, AutoStick is not active.  WARNING: Do not downshift for additional engine braking on a slippery surface.  The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.", "Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.", "Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately \"\u21e8air bag warning light\" .  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning", "as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bags to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Placing an object on", "you drive, have an authorized dealer service the air bag system immediately.  Placing an object on the floor under the front passenger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision.  Do not place any objects on the floor under the front passenger seat.  If there is a fault present in the OCS, both the PAD Indicator Light and the Air Bag Warning Light will illuminate to show that the Passenger Advanced Front Air Bag is deactivated.  Should this occur, the Passenger Advanced Front Air Bag will remain deactivated until the fault is cleared.  This indicates that you should take the vehicle to an authorized dealer for service immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light", "Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light will illuminate whenever the ocs is unable to classify the front passenger seat status.  A malfunction in the OCS may affect the operation of the air bag system.  If the air bag warning light does not come on, or stays on after you start the vehicle, or it comes on as you drive, take the vehicle to an authorized dealer for service immediately.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check", "Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Air Bag Warning Light This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on", "stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  Air Bag Warning Light The Occupant Restraint Controller (ORC) monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position.  If the ignition switch is in the OFF position or in the ACC position, the air bag system is not on and the air bags will not inflate.  The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or it becomes disconnected prior to deployment.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light,", "If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is detected that could affect the air bag system.  The diagnostics also record the nature of the malfunction.  While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  Note: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint", "the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled.  In this condition the air bags may not be ready to inflate for your protection.  have an authorized dealer service the air bag system immediately.  WARNING: Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.", "Manual Seat Height Adjustment The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.  Manual Front Seat Forward/Rearward Adjustment The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  WARNING: Adjusting a seat while driving may be dangerous.  Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death.  Seats should be adjusted before fastening the seat belts and while the", "serious injury or death.  Seats should be adjusted before fastening the seat belts and while the vehicle is parked.  Serious injury or death could result from a poorly adjusted seat belt.  Lumbar Support The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  Manual Seat Height Adjustment The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.  Adjustable Upper Shoulder Belt Anchorage In the driver and outboard front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck.  Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that", "squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.  As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position.  After you release the anchorage button, try to move it up or down to make sure that it is locked in position.  Note: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature.  This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release button.  To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position.  WARNING: Wearing your seat belt incorrectly could make your injuries in a collision much worse.  You might suffer internal injuries, or you could even slide out of the seat belt.  Follow these instructions to wear your seat", "or you could even slide out of the seat belt.  Follow these instructions to wear your seat belt safely and to keep your passengers safe, too.  Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and not resting on your neck.  The retractor will withdraw any slack in the shoulder belt.  Misadjustment of the seat belt could reduce the effectiveness of the safety belt in a crash.  Always make all seat belt height adjustments when the vehicle is stationary.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.", "your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Secondary Method For Oil Change Reset Procedure Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the", "pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Note: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.  If necessary, repeat this procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be", "(805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in", "with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means", "Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000", "follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a", "dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both", "the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the", "If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your", "involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm", "one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system", "is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a", "Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  When the Display button is pressed on the touchscreen, the system will display the options related to the theme (if equipped), brightness, and color of the touchscreen.  The available settings are: note: depending on the vehicle\u2019s options, feature settings may vary.  MAX A/C Button Press and release the MAX A/C button on the touchscreen to change the current setting to the coldest output of air.  MAX A/C sets the control for maximum cooling performance.  The MAX A/C indicator illuminates when MAX A/C is on.  Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.  Note:", "the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.  Note: The MAX A/C button is only available on the touchscreen.", "Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada) symbols key if you do not read the entire owner\u2019s manual, you may miss important information.  Observe all Cautions and Warnings.  Service Manuals These comprehensive Service Manuals provide a complete working knowledge of the vehicle, system, and/or components and is written in straightforward language with illustrations, diagrams, and charts.  Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage Owner's Manuals, Radio Manuals and Warranty Information Books", "Vehicle delivery date and mileage Owner's Manuals, Radio Manuals and Warranty Information Books can be ordered through Archway at: To order the following manuals, you may use either the website or the phone numbers listed below.  Owner's Manuals If you do not read the entire Owner\u2019s Manual, you may miss important information.  Observe all Cautions and Warnings.  Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada).", "Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all", "system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a", "testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you", "ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the", "going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the", "The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "The Uconnect system is a sophisticated electronic device.  Do not let young children use the system.  Permanent hearing loss may occur if you play your music or sound system at loud volumes.  Exercise caution when setting the volume on the system.  Keep drinks, rain and other sources of moisture away from the system.  Besides damage to the system, moisture can cause electric shocks as with any electronic device.  It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.  Uconnect Phone is a voice-activated, hands-free, in-vehicle communications system.  It allows you to dial a phone number with your mobile phone.  Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling contacts", "Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling contacts from Phonebooks displayed on the touchscreen.  Setting Favorite Contact phone numbers so they are easily accessible on the Main Phone screen.  Viewing and Calling contacts from Recent Call logs.  Reviewing your recent Incoming SMS Messages.  Pairing up to 10 phones/audio devices for easy access to connect to them quickly.  Your mobile phone\u2019s audio is transmitted through your vehicle\u2019s audio system; the system will automatically mute your radio when using the Uconnect Phone.  For uconnect customer support: us visit uconnectphone.com or call 877-855-8400 canada visit uconnectphone.com or call 800-465-2001 (english) or (french) call 800-387-9983 uconnect phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile", "conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  Note: Your phone must be capable of SMS messaging via Bluetooth\u00ae for messaging features to work properly.  WARNING: ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the Uconnect features and applications in this vehicle.  Only use Uconnect when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Safe Usage Of The Uconnect System The", "may result in an accident involving serious injury or death.  Safe Usage Of The Uconnect System The Uconnect system is a sophisticated electronic device.  Do not let young children use the system.  Permanent hearing loss may occur if you play your music or sound system at loud volumes.  Exercise caution when setting the volume on the system.  Keep drinks, rain and other sources of moisture away from the system.  Besides damage to the system, moisture can cause electric shocks as with any electronic device.  Note: Many features of this system are speed dependent.  For your own safety, it is not possible to use some of the touchscreen features while the vehicle is in motion.  Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling contacts from Phonebooks displayed on the touchscreen.  Setting Favorite Contact phone numbers so they are easily accessible on the Main Phone screen.  Viewing and Calling contacts from Recent Call logs.  Reviewing your recent Incoming SMS Messages.", "Viewing and Calling contacts from Recent Call logs.  Reviewing your recent Incoming SMS Messages.  Pairing up to 10 phones/audio devices for easy access to connect to them quickly.  Your mobile phone\u2019s audio is transmitted through your vehicle\u2019s audio system; the system will automatically mute your radio when using the Uconnect Phone.  For uconnect customer support: us visit uconnectphone.com or call 877-855-8400 canada visit uconnectphone.com or call 800-465-2001 (english) or (french) call 800-387-9983 uconnect phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been", "wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  Note: Your phone must be capable of SMS messaging via Bluetooth\u00ae for messaging features to work properly.  WARNING: ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the Uconnect features and applications in this vehicle.  Only use Uconnect when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Multiple Devices Connecting To The Uconnect System \u2014 If Equipped It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text", "CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.  Note: Apple CarPlay\u00ae and Android Auto\u2122 can only be launched from the front and center console USB ports.", "Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be", "these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the", "upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside),", "Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.", "or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels", "top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Remove both front panels Open both front doors.  Using the provided #50 Torx head driver and ratchet, remove the two Torx head", "both front doors.  Using the provided #50 Torx head driver and ratchet, remove the two Torx head screws that secure the hard top at the B-pillar (near the top of the front doors).  Step Three If equipped, remove the lower interior soft trim panel (attached by the hook-and-loop fastener) by pulling the panel away from the trim.  Step Four Remove the Torx head fasteners that secure the hard top to the vehicle: two along the interior body side, rearward of the back doors, followed by the four fasteners along the back of the vehicle cab using the #T50 Torx head driver.  Step Five 1 \u2014 Vehicle Cab Torx Head Fasteners 2 \u2014 Body side Torx Head Fasteners Locate the wire harness on the left rear inside corner of the vehicle.  To access the harness, remove the plastic cover by pushing the cover to the side, and sliding it off.  Do not force open; this will break the plastic cover.  Step Six To release the wire harness, pull back on the red latch (1), then push down on the black button (2) while pulling the harness out.", "back on the red latch (1), then push down on the black button (2) while pulling the harness out.  Step Seven 1 \u2014 Red Latch 2 \u2014 Black Button Remove the hard top from the vehicle.  Install the provided edge protectors along the bottom edges of the hard top, and place the hard top on a soft surface to prevent damage.  The removal of the Hard Top requires four adults located on each corner.  Failure to follow this caution could damage the Hard Top.  Store the wire harness by removing the storage cover on the quarter trim.  Use the mechanical key blade to pry the cover open.  Step Nine Tuck the wire harness inside the storage compartment, and replace the cover.", "Battery Charge Warning Light This warning light will illuminate when the battery is not charging properly.  If it stays on while the engine is running, there may be a malfunction with the charging system.  Contact an authorized dealer as soon as possible.  This indicates a possible problem with the electrical system or a related component.  Battery Charge Warning Light This warning light will illuminate when the battery is not charging properly.  If it stays on while the engine is running, there may be a malfunction with the charging system.  Contact an authorized dealer as soon as possible.  This indicates a possible problem with the electrical system or a related component.  Red warning lights air bag warning light \"\u21e8air bag warning light\" brake warning light \"\u21e8brake warning light\" battery charge warning light \"\u21e8battery charge warning light\" door open warning light \"\u21e8door open warning light\" electric power steering (eps) fault warning light \"\u21e8electric power steering (eps) fault warning light\" electronic", "steering (eps) fault warning light \"\u21e8electric power steering (eps) fault warning light\" electronic throttle control (etc) warning light \"\u21e8electronic throttle control (etc) warning light\" engine coolant temperature warning light \"\u21e8engine coolant temperature warning light\" hood open warning light \"\u21e8hood open warning light\" oil pressure warning light \"\u21e8oil pressure warning light\" oil temperature warning light \"\u21e8oil temperature warning light\" seat belt reminder warning light \"\u21e8seat belt reminder warning light\" rear seat belt reminder warning light \"\u21e8rear seat belt reminder indicator light \u2014 if equipped with a base instrument cluster\" transmission temperature warning light \"\u21e8transmission temperature warning light \u2014 if equipped\" vehicle security warning light \"\u21e8vehicle security warning light \u2014 if equipped\" loose fuel filler cap warning light \u2014 if equipped this warning light will illuminate when the fuel filler cap is loose.  Properly close the filler cap to disengage the light.  If the light does not turn off,", "is loose.  Properly close the filler cap to disengage the light.  If the light does not turn off, please see an authorized dealer.  The charging system is independent from load reduction.  The charging system performs a diagnostic on the charging system continuously.  If the Battery Charge Warning Light is on it may indicate a problem with the charging system This warning light will illuminate when the battery is not charging properly.  If it stays on while the engine is running, there may be a malfunction with the charging system.  Contact an authorized dealer as soon as possible.  Red Warning Lights Air Bag Warning Light \"\u21e8Air Bag Warning Light\" Brake Warning Light \"\u21e8Brake Warning Light\" Battery Charge Warning Light \"\u21e8Battery Charge Warning Light\" Door Open Warning Light \"\u21e8Door Open Warning Light\" Electric Power Steering (EPS) Fault Warning Light \"\u21e8Electric Power Steering (EPS) Fault Warning Light\" Electronic Throttle Control (ETC) Warning Light \"\u21e8Electronic Throttle Control (ETC) Warning Light\" Engine", "Throttle Control (ETC) Warning Light \"\u21e8Electronic Throttle Control (ETC) Warning Light\" Engine Coolant Temperature Warning Light \"\u21e8Engine Coolant Temperature Warning Light\" Hood Open Warning Light \"\u21e8Hood Open Warning Light\" Oil Pressure Warning Light \"\u21e8Oil Pressure Warning Light\" Oil Temperature Warning Light \"\u21e8Oil Temperature Warning Light\" Seat Belt Reminder Warning Light \"\u21e8Seat Belt Reminder Warning Light\" Rear Seat Belt Reminder Warning Light \"\u21e8Rear Seat Belt Reminder Indicator Light \u2014 If Equipped With A Base Instrument Cluster\" Transmission Temperature Warning Light \"\u21e8Transmission Temperature Warning Light \u2014 If Equipped\" Vehicle Security Warning Light \"\u21e8Vehicle Security Warning Light \u2014 If Equipped\" This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced", "is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  With extended use the Hazard Warning Flashers may wear down your battery.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a", "indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  This warning light will illuminate when the Stop/Start system is not functioning properly and service is required.  Contact an authorized dealer for service.  This warning light will turn on when there's a fault with the EPS system The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.", "AUTOMATIC TRANSMISSION \u2014 IF EQUIPPED You must press and hold the brake pedal while shifting out of PARK.  WARNING: Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not", "to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked", "and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  CAUTION: Shift into or out of PARK or REVERSE only after the vehicle has come to a complete stop.  Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed.  Before shifting into any gear, make sure your foot is firmly pressing the brake pedal.  Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle", "brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift", "or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned", "of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  You or others could be injured or killed if you leave the", "of all interior and exterior lights.  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied.  The parking brake should always be applied when the driver is not in the vehicle, especially on an incline.  Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the", "and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or", "in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.", "Replacing The Battery In The Key Fob The recommended replacement battery is CR2450.  Remove the back cover of the key fob by inserting a flat-blade screwdriver into the slot on the bottom of the fob.  Apply light pressure until the cover unsnaps being careful not to damage the seal.  Proceed counterclockwise (in the order shown in the following image) to loosen the remaining snaps until the battery cover can be removed.  1-3 \u2013 back cover pry points remove the depleted battery by inserting a small flat-blade screwdriver into the battery removal slot and sliding the battery forward and upward being careful not to damage the electronic board underneath.  Battery replacement install the new battery into the key fob, making sure the positive (+) side is facing up.  Slide the battery until it is seated securely below the tabs.  Reassemble the back cover making sure it is properly aligned before snapping it back in place.  Note: Customers are recommended to use a battery obtained from Mopar\u00ae.  Aftermarket coin", "in place.  Note: Customers are recommended to use a battery obtained from Mopar\u00ae.  Aftermarket coin battery dimensions may not meet the original OEM coin battery dimensions.  Perchlorate material \u2014 special handling may apply.  See www.dtsc.ca.gov/hazardouswaste/perchlorate for further information.  Do not touch the battery terminals that are on the back housing or the printed circuit board.  When a key fob battery is low, a warning will be indicated on the vehicle\u2019s instrument cluster, and the fob LED will no longer illuminate with a button push.  WARNING: The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop", "and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.", "facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical", "integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  The battery in your vehicle is located in the right rear of the engine compartment.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  The Power Distribution Center is located", "on the passenger side under the instrument panel.  The Power Distribution Center is located in the engine compartment near the battery.  This center contains cartridge fuses, mini fuses, and relays.  The PDC top cover is labeled with each serviceable fuse/relay location, function, and size.", "Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts", "After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.  WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.  Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly calibrated torque wrench using a six-sided (hex) deep wall socket.  Lug nut/bolt torque **lug nut/bolt size lug nut/bolt socket size 130 ft-lb (176 n\u00b7m) m14 x 1.50 mm 22 mm.  Torque Specifications **Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.  Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.", "the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  WARNING: To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts/bolts fully until the vehicle has been lowered.  Failure to follow this warning may result in personal injury.", "A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  A/C Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Note: For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned", "For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause", "performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic mode \"\u21e8automatic operation\" .", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The rear seatback can be locked using the vehicle key to", "this caution could damage the hard top.  The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  This vehicle has front air bags and lap/shoulder belts for both the driver and front passenger.  The front air bags are a supplement to the seat belt restraint systems.  The driver front air bag is mounted in the center of the steering wheel.  The passenger front air bag is mounted in the instrument panel, above the glove compartment.  The words \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d are embossed on the air bag covers.  This vehicle has an Occupant Classification System (\u201cOCS\u201d) in the front passenger seat.  The OCS is designed to activate or deactivate the Passenger Advanced Front Air Bag depending on the occupant\u2019s seated weight.  It is designed to deactivate the Passenger Advanced Front Air Bag for an unoccupied seat and for occupants whose", "to deactivate the Passenger Advanced Front Air Bag for an unoccupied seat and for occupants whose seated weight classifies them in a category other than a properly seated adult.  This could be a child, teenager, or even an adult.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation.  The entire vehicle should first be weighed on a commercial scale to ensure that the GVWR has not been exceeded.  The weight on the front and rear of the vehicle should then be determined separately to be sure that the load is", "the front and rear of the vehicle should then be determined separately to be sure that the load is properly distributed over the front and rear axle.  Weighing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.  If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met.  Store the heavier items down low and be sure that the weight is distributed equally.  Stow all loose items securely before driving.  Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate.  WARNING: Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR.  If you do, parts on your vehicle can break, or it can change the way your vehicle handles.  This could cause you to lose control.  Overloading can shorten the life of your vehicle.", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the", "menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING:", "display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and", "mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Rear Seat Unoccupied Indicator Light \u2014 If Equipped This light indicates when the rear passenger seats are unoccupied, and will illuminate in the upper right portion of the instrument cluster display, momentarily replacing the configurable corner information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the", "information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed", "mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the", "vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR", "clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected", "time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If", "if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.", "may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory", "smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The", "engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse", "maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle", "or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.", "The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom", "Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage", "The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium", "below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.", "Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  If the \u201cSERVICE POWER STEERING\u201d", "Normal operation will resume once the system is allowed to cool.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function.  However, the effort required to brake the vehicle will be much greater than that required with the power system operating.  If the stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the", "stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not attempt to drive the vehicle over 18 mph (29 km/h).  Driving faster than 18 mph (29 km/h) with a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  When the condition that deactivated the system is no longer present, the system will return to the \u201cAdaptive Cruise Control Off\u201d state and will resume function by simply reactivating it.  There may be situations where the Hill Start Assist (HSA) will not activate and slight rolling may occur, such as on minor hills or with a loaded vehicle, or while pulling a trailer.  HSA is not a substitute for active driving involvement.  It is always the", "while pulling a trailer.  HSA is not a substitute for active driving involvement.  It is always the driver\u2019s responsibility to be attentive to distance to other vehicles, people, and objects, and most importantly brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision or serious personal injury.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized", "on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off CAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial", "it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may", "are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offCAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.", "To use the mid position, open the tailgate and lower it to near mid position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  Tailgate In Mid Position  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014", "the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located", "provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.", "Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the", "you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you", "is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  Getting High-Centered If you get hung up or", "every effort to cross the large rocks with your tires.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION:", "abuse.  Always look ahead and make every effort to cross the large rocks with your tires.  CAUTION: Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.  Never attempt to drive over a rock which is large enough to contact the door sills.  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on", "Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.", "WARRANTY INFORMATION See the Warranty Information for the terms and provisions of FCA US LLC warranties applicable to this vehicle and market.  Refer to www.mopar.com/om for further information.  See the Warranty Information for the terms and provisions of FCA Canada Inc.warranties applicable to this vehicle and market.  Refer to www.owners.mopar.ca/en for further information.  Use this QR code to access your digital experience.  Who is Covered You are covered by Roadside Assistance services if you are a purchaser for use of the vehicle.  Roadside Assistance services last for five years or 60,000 miles on the odometer, whichever occurs first, calculated from the start date of the Basic Limited Warranty, as set forth in your Warranty Information book.  1 1.  Towing services provided through Cross Country Motor Club, Inc. Medford, MA 02155, except in AK,CA, HI, OR, WI, and WY, where services are provided by Cross Country Motor Club of California, Inc., Thousand Oaks, CA 91360.  Who is Covered You are covered", "Country Motor Club of California, Inc., Thousand Oaks, CA 91360.  Who is Covered You are covered by Roadside Assistance services if you are a purchaser for use of the vehicle.  Roadside Assistance services last for five years or 60,000 miles on the odometer, whichever occurs first, calculated from the start date of the Basic Limited Warranty, as set forth in your Warranty Information book.  1 1.  Towing services provided through Cross Country Motor Club, Inc.Medford, MA 02155, except in AK,CA, HI, OR, WI, and WY, where services are provided by Cross Country Motor Club of California, Inc., Thousand Oaks, CA 91360.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.", "your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil", "to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no", "completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator", "within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To", "this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will", "(805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on", "system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect", "against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.", "vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code", "leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants", "are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the", "the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric topDo not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top \u00b9 use", "installation can cause water to leak into the vehicle's interior.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top", "Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.", "Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1)", "and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  All cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  (1) Locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.\u201d on your vehicle's placard.  Opening To open the tailgate, pull the release handle located on the center of the tailgate", "Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two", "box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed,", "tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.", "Press the settings button on the touchscreen.  Press the paired phones or audio sources button.  Press to select the particular phone or the particular audio device.  A pop-up menu will appear; press \u201cConnect Phone\u201d.  Press the X to exit out of the Settings screen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The MAX A/C button is only available on the touchscreen.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and", "scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsThe SYNC button is only available on the touchscreen.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Press the Phone button.  Press the Dial/Keypad button on the touchscreen.  The Touch-Tone screen will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press", "will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press \u201cDial/Call\u201d.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  Overview Bluetooth\u00ae Streaming Audio or Bluetooth\u00ae Mode is entered by pairing a Bluetooth\u00ae device, containing music, to the Uconnect system.  Before proceeding, the Bluetooth\u00ae device must be paired to the Uconnect Phone to communicate with the Uconnect system.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark", "menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and", "the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow", "pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.", "Daytime Running Lights (DRLs) \u2014 If Equipped The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  Note: For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  Vehicles sold in Canada are equipped with a headlight switch with an AUTO", "(manual transmission).  Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  \"R\" means radial construction, or \"D\" means diagonal or bias construction Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered in the US and other countries.  Apple\u00ae terms of use and privacy statements apply.  Vehicles", "in the US and other countries.  Apple\u00ae terms of use and privacy statements apply.  Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic", "active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  BeltAlert can be activated or deactivated by an authorized dealer.  FCA US LLC does not recommend deactivating BeltAlert.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service", "is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors", "a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software,", "into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact", "you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by", "updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but", "engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.", "the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable", "The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the", "Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the", "Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "Replacing the wiring connector into the wiring harness to reinstall the wiring connector on the vehicle\u2019s door into the harness just inside the vehicle, proceed as follows: with light finger pressure, seat the wiring connector straight into the wiring harness until the wiring harness lever starts to lower with the latching pin.  Connecting the wiring harness 1 \u2014 seat connector straight into harness 2 \u2014 wiring harness lever starts to lower caution: failure to correctly reconnect the wiring connector into the harness will result in damage that is not covered by the new vehicle warranty.  After the harness lever has started to move with the pressure of seating the wiring connector, continue by lowering the wiring harness lever to the fully closed position.  Fully closed position push the red locking tab downward to lock into place.  Attach the cloth strap of the door onto the metal hook just inside the vehicle.  Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap replace wiring access doors.  Note: Make sure", "Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap replace wiring access doors.  Note: Make sure there is plenty of slack on the wiring connector during installation.  Close the door slightly to provide more slack if needed.  Note: When reinstalling the door check arm attachment screw, screw torque should be between 11.76 ft\u00b7lb / 16 N\u00b7m and 27.9 ft\u00b7lb / 38 N\u00b7m.  Rear door removal rear door removal \u00b9 use this qr code to access your digital experience.  To remove the rear doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nuts from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin under the rear seat.  Hinge pin nut slide the front seat(s) fully forward.  Pry open and remove the plastic wiring access door from the bottom of the B-pillar.  Wiring access door unplug the wiring connector.  Note: squeeze the tab on the base of the wiring harness.  This will unlock the connector tab,", "Note: squeeze the tab on the base of the wiring harness.  This will unlock the connector tab, allowing the wiring connector to be unplugged.  Unhook the wire harness strap from the hook on the body side.  Store the wire connector in the lower basket of the door.  Wiring connector with the door in the open position, remove the check bolt from the door check attachment on the body (using a #t40 torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  To reinstall the door(s), perform the previous steps in the reverse order.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear", "this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  WARNING: To avoid personal injury be sure to keep your arms, hands, fingers and all objects clear of the check arm area during the removal and installation procedures.  Note: The upper hinge has a longer pin, which can be used to assist in guiding the door into place when reinstalling.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb", "CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Installing The Rear Window And Quarter Panel Cover Assemblies If the rear window and quarter panel cover assemblies were previously removed, proceed as follows to install: Guide the top of the quarter panel cover assembly up into the retainer.  Step one caution: failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the soft top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step two note: it is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide", "corner of each quarter panel cover assembly by pressing firmly.  Step three from either side, guide the rear window into the retainer while keeping the window level.  Step four engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step five engage the vertical retainers up the right and left side of the rear window.  Step six tuck the rear window under the soft top fabric and press firmly.  Step seven engage the rear window retainers in the lower right and left corners.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.", "Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  Manual", "for child seats and/or passengers.  An improperly latched seat could cause serious injury.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Important Safety Precautions Please pay close attention to the information in this section.  It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.  Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: Children 12 years old and under should always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big", "always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint Never allow children to slide the shoulder belt behind them or under their arm.  You should read the instructions provided with your child restraint to make sure that you are using it properly.  All occupants should always wear their lap and shoulder belts properly.  The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate.  Do not lean against the door or window.  If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and", "occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.  If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see \"\u21e8if you need assistance\" for customer service contact information.  WARNING: Never place a rear-facing child restraint in front of an air bag.  A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.  Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing child restraint in the rear seat.  If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle.  Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.", "the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to", "will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Hazard Warning Flashers Button The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the", "or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Warning CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks 1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Button  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Hazard Warning Flashers Button With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit", "the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.  turn on the Hazard Warning Flashers.  Apply the parking brake firmly and shift an automatic transmission in PARK; a manual transmission to REVERSE.  Block the wheel diagonally opposite the wheel to be raised.  Never start or run the engine with the vehicle on a jack.  Do not let anyone sit in the vehicle when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get", "when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.  Only use the jack in the positions indicated and for lifting this vehicle during a tire change.  If working on or near a roadway, be extremely careful of motor traffic.  To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.", "Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose", "the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.", "and power steering, and fill as needed.  Check function of all interior and exterior lights.  PARKING BRAKE Before exiting the vehicle, make sure that the parking brake is fully applied.  Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or FIRST gear.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to", "selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  WARNING: Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  CAUTION: If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  See the following steps to use", "Have the brake system serviced by an authorized dealer immediately.  See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle", "Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and", "it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear", "the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Start by removing the rear window first.  Use the two straps located on the bottom of each", "Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the", "the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Guide the top of the quarter panel cover assembly up into the retainer.  Step One Failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the Soft Top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step Two It is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step Three From either side, guide the rear window into the retainer while keeping the window level.  Step Four Engage the retainer along the bottom of the rear", "while keeping the window level.  Step Four Engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step Five Engage the vertical retainers up the right and left side of the rear window.  Step Six Tuck the rear window under the soft top fabric and press firmly.  Step Seven Engage the rear window retainers in the lower right and left corners.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step Two 1 \u2014 Outside Panel Lock 2 \u2014 Rear Panel Lock 3 \u2014 Front Panel Lock Unlatch the left side header panel latch located at the top of the windshield.  Step Three Remove the left side panel.  Repeat the preceding steps to remove the right side panel.", "Do not use abrasive cleaning components, solvents, steel wool, or other aggressive material to clean the lenses.  The lenses in front of the instruments in this vehicle are molded in clear plastic.  When cleaning the lenses, care must be taken to avoid scratching the plastic.  Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsTo minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.  To remove road", "of scratching the lenses and reducing light output, avoid wiping with a dry cloth.  To remove road dirt, wash with a mild soap solution followed by rinsing.  If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  If the \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the windshield and forward-facing camera inspected at an authorized dealer.  All glass surfaces should be cleaned on a regular basis with Mopar\u00ae Glass Cleaner, or any commercial household-type glass cleaner.  Never use an abrasive type cleaner.  Use caution when cleaning the inside rear window equipped with electric defrosters or windows equipped", "caution when cleaning the inside rear window equipped with electric defrosters or windows equipped with radio antennas.  Do not use scrapers or other sharp instruments that may scratch the elements.  The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems are experienced.  This inspection should include the following points:  Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic.  When cleaning the lenses, care must be taken to avoid scratching the plastic.  Clean with a wet soft cloth.  A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.  If soap is used, wipe clean with a clean damp cloth.  Dry with a soft cloth.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the", "required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash", "with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.", "If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all", "the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low", "It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and", "injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can", "windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold", "the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.", "In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervalsYour vehicle is equipped with dual hydraulic brake systems.  If either of the two hydraulic systems lose normal capability, the remaining system will still function.  However, there will be some loss of overall braking effectiveness.  You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.  If the driver does not take action based upon these progressive warnings, then the system will provide a limited level of active braking to help slow the vehicle and mitigate the potential forward collision.  If the driver reacts to the warnings by braking and the system determines that the driver intends to avoid the collision by braking but has not applied sufficient brake force, the system will compensate and provide additional brake force as required.  The BAS is designed to", "the system will compensate and provide additional brake force as required.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting", "afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user's safety or the safety of others.  Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The ACC system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped", "system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems.  If either of the two hydraulic systems lose normal capability, the remaining system will still function.  However, there will be some loss of overall braking effectiveness.  You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.  In the event power assist is lost", "or stop, and potential activation of the Brake Warning Light.  In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function.  However, the effort required to brake the vehicle will be much greater than that required with the power system operating.  Brake System In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervals WARNING: Riding the brakes can lead to brake failure and possibly a collision.  Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.  You would not have your full braking capacity in an emergency.  Brake Assist System (BAS) The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and", "detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  WARNING: The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous", "The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user's safety or the safety of others.  Brake System In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervals WARNING: Riding the brakes can lead to brake failure and possibly a collision.  Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.  You would not have your full braking capacity in an emergency.", "Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWRWARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do", "and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.", "If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for serviceIn unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature", "whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the", "procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an", "reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  To Turn Off The Engine Using The ENGINE START/STOP Button Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain", "for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Note: The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Note: depending on the vehicle\u2019s options, feature settings may vary.  Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and", "off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.", "frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still", "the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.", "Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.  When the Display button is pressed on the touchscreen, the system will display the options related to the theme (if equipped), brightness, and color of the touchscreen.  The available settings are: note: depending on the vehicle\u2019s options, feature settings may vary.  MAX A/C Button", "settings are: note: depending on the vehicle\u2019s options, feature settings may vary.  MAX A/C Button Press and release the MAX A/C button on the touchscreen to change the current setting to the coldest output of air.  MAX A/C sets the control for maximum cooling performance.  The MAX A/C indicator illuminates when MAX A/C is on.  Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.  Note: The MAX A/C button is only available on the touchscreen.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c", "if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.", "In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this", "to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeHow long does it take to remotely start my vehicle?  Depending on various conditions, it can take three minutes or more for the request to get", "vehicle?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will remote start your vehicle more quickly.  However its range is limited.  For example, when you are leaving the stadium after the game, you can use the Vehicle Branded App to remote start your vehicle and have the inside of your vehicle comfortable by the time you get to it.  Will my vehicle be safe if I lose my wireless device?  People sometimes lose their wireless devices, which is why security measures have been engineered into the Vehicle Branded App.  Asking for your username, password and SiriusXM Guardian\u2122 Security PIN help to ensure that nobody can start your vehicle if they happen to find your device.  Can someone drive off with my vehicle using the App?  nob Driving your vehicle still requires the keys to be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the", "be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the interior before you arrive.  Can I stop a vehicle that is being driven with the cancel Remote Vehicle Start command?  nob If the vehicle is in motion, the cancel Remote Vehicle Start button will not stop the vehicle.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal", "Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.", "Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and", "it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Removing The Rear Window And Quarter Panel Cover Assemblies Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step one (right side shown) step one while keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear", "the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step two after removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step four pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step five repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Note: both quarter panel cover assemblies and the rear window must all be removed together, or installed together.  Start by removing the rear window first.  Use the two straps located on the bottom of each", "Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe locationStep Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the", "the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Guide the top of the quarter panel cover assembly up into the retainer.  Step One Failure to follow all quarter panel cover assembly and rear window install steps could result in damage to the Soft Top or vehicle.  Engage the plastic retainers on the front of the cover assembly (toward the front of the vehicle) starting at the top, and working downward.  Step Two It is critical that the retainers are fully engaged before the vehicle resumes motion.  Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover assembly by pressing firmly.  Step Three From either side, guide the rear window into the retainer while keeping the window level.  Step Four Engage the retainer along the bottom of the rear", "while keeping the window level.  Step Four Engage the retainer along the bottom of the rear window beginning on the left side of the vehicle and working toward the center.  Then, move to the right side of the vehicle and continue from the center, working to the right until the rear window is secured in the lower retainer.  Step Five Engage the vertical retainers up the right and left side of the rear window.  Step Six Tuck the rear window under the soft top fabric and press firmly.  Step Seven Engage the rear window retainers in the lower right and left corners.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step Two 1 \u2014 Outside Panel Lock 2 \u2014 Rear Panel Lock 3 \u2014 Front Panel Lock Unlatch the left side header panel latch located at the top of the windshield.  Step Three Remove the left side panel.  Repeat the preceding steps to remove the right side panel.", "Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the", "start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: The message will stay active until the ignition is placed in the ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP", "ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  To insert an Auxiliary device, gently insert the Auxiliary device cable into the AUX port.  If you insert an Auxiliary device with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system", "with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is", "which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on", "obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Different colored zones indicate the distance to the rear of the vehicle.  The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.", "speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously", "speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  Manual Activation Of The Rear View Camera  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will", "view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in", "pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical", "in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the", "connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these", "in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.  Note: Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle while making connections.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack,", "alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two", "Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and", "Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have", "discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.", "See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you", "See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking", "engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch", "and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center", "Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  This mirror automatically adjusts for headlight glare", "cupholders, and front door handles).  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.", "ParkSense Sensors The four ParkSense sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 79 inches (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.  The six ParkSense sensors, located in the front fascia/bumper, monitor the area in front of the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 47 inches (120 cm) from the front fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.  The ParkSense Park Assist system provides visual and audible indications of the distance between the rear and/or front fascia/bumper and a detected obstacle when backing up or moving forward (e.g.  during a parking maneuver).  For system limitations and usage precautions, see", "forward (e.g.  during a parking maneuver).  For system limitations and usage precautions, see ParkSense will turn off the Front Park Assist audible alert (chime) after approximately three seconds when an obstacle has been detected, the vehicle is stationary, and the brake pedal is applied.  ParkSense can be active only when the gear selector is in REVERSE or DRIVE.  If ParkSense is enabled at one of these gear selector positions, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above.  A warning will appear in the instrument cluster display indicating the vehicle is above ParkSense operating speed.  The system will become active again if the vehicle speed is decreased to less than approximately 6 mph (9 km/h).  The ParkSense Warning screen is located within the instrument cluster display It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.  ParkSense is only a parking aid", "and/or front fascia/bumper and the detected obstacle.  ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles.  Parking curbs might be temporarily detected or not detected at all.  Obstacles located above or below the sensors will not be detected when they are in close proximity.  The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected.  It is recommended that the driver looks over his/her shoulder when using ParkSense.  Setting Name Description Forward Collision Warning Sensitivity This setting will change the distance at which the Forward Collision Warning (FCW) alert sounds.  The \u201cMedium\u201d setting will have the FCW system signal when an object is in view, and the possibility of a collision is detected.  The \u201cNear\u201d setting will have the FCW system signal when the object is closer to the vehicle.  The \u201cFar\u201d setting will have the FCW system signal when an object is at a far distance from the", "The \u201cFar\u201d setting will have the FCW system signal when an object is at a far distance from the vehicle.  Forward Collision Warning This setting will turn the Forward Collision Warning system on or off.  The \u201cOff\u201d setting will deactivate the FCW system.  The \u201cWarning Only\u201d setting will provide only an audible chime when a collision is detected.  The \u201cWarning + Active Braking\u201d setting will provide an audible chime and apply some brake pressure when a collision is detected.  ParkSense This setting will change the type of ParkSense alert when a close object is detected and can provide both an audible chime and a visual display when an object is detected.  Front ParkSense Volume This setting adjusts the volume of the Front ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Rear ParkSense Volume This setting adjusts the volume of the Rear ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Blind Spot Alert This setting will change the type of alert provided when an", "\u201cMedium\u201d, and \u201cHigh\u201d.  Blind Spot Alert This setting will change the type of alert provided when an object is detected in a vehicle\u2019s blind spot.  The \u201cOff\u201d setting will turn off Blind Spot Alert.  The \u201cLights\u201d setting will activate the Blind Spot Alert lights on the outside mirrors.  The \u201cLights & Chime\u201d setting will activate both the lights on the outside mirrors and an audible chime.  Hill Start Assist This setting will turn the Hill Start Assist system on or off.  ParkView Backup Camera Active Guidelines This setting will turn the ParkView Backup Camera Active Guidelines on or off.  ParkView Backup Camera Delay This setting will add a timed delay to the ParkView Backup Camera when shifting out of REVERSE.  Fixed ParkView Backup Camera Guidelines This setting will turn the Fixed ParkView Backup Camera Guidelines on or off.  Front Camera Gridlines This setting will turn the Front Camera Gridlines on or off.  Tire Fill Assist This setting will turn Tire Fill Assist on or off.  ParkSense Warning Display The", "Tire Fill Assist This setting will turn Tire Fill Assist on or off.  ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster displayIt provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.", "When To Use 4L Range When off-road driving, shift into 4L for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low speed pulling power.  This range should be limited to extreme situations such as deep snow, mud, steep inclines, or sand where additional low speed pulling power is needed.  Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4L range.  CAUTION: Do not use 4L range when operating the vehicle on dry pavement.  Driveline hardware damage can result.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street", "in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument", "to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the", "provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the", "4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.", "Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the", "the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact.  Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.  This feature notifies the user when the placard tire pressure is attained while inflating or deflating the tire.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof", "to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  The functions described are for when the Jeep\u00ae wireless speaker is undocked from the vehicle.  When plugged into the docking station, the Jeep\u00ae wireless speaker functions as part of the vehicle\u2019s sound system.  The Jeep\u00ae wireless speaker is IP67 waterproof certified with design in mind to withstand rainfall, waterjets, splashing and being submerged in up to 3 ft (1 m) of water for up to 30 minutes.", "When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  Avoid", "Before getting out of the vehicle, be sure to check that there is no one left inside.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Child-Protection Door Lock System \u2014 Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove the sealing plug for access, and use a flat-blade screwdriver (or mechanical key) to rotate the dial to the lock or unlock position.  Note: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection", "the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Note: Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  When the Child-Protection Door Lock system is engaged, the door can be", "is no one left inside.  When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Child-Protection Door Lock Location", "Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app", "available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a", "plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Apps The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear", "Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular", "you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Description SmartWatch Integration puts the Vehicle Branded App right on your", "on the touchscreen.  Description SmartWatch Integration puts the Vehicle Branded App right on your Apple\u00ae Watch or Android\u2122 Wear.  To get started, follow these steps: Download the Vehicle Branded App from the App Store\u00ae or Google Play.  Log onto the app from your smartphone using the username and password you created when you first set up your account.  Make sure your watch and smartphone are connected through Bluetooth\u00ae.  The Vehicle Branded App should appear on your SmartWatch.  Once the app is downloaded on your SmartWatch, you can enjoy these features: Lock or unlock your vehicle by tapping the remote lock button in the app and entering your security PIN.  Remote start or stop your vehicle.  View important vehicle stats, such as fuel level, vehicle location, tire pressure warning, and more.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was", "smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into", "the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your", "data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or", "The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 \u00b9 use this qr code to access your digital experience.  While using Android Auto\u2122, Google Maps\u2122 provides voice-guided:", "Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact", "background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected,", "will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands", "using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait", "while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice", "natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the", "vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure", "it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always", "inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children", "in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on", "or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the", "location accessible to children.  A child could operate power windows, other controls, or move the vehicle.", "Off-Road Driving Tips  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled", "you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface", "should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?", "Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too", "gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat,", "the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating,", "off immediately and call for service.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as", "the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take", "the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the", "system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service", "Before You Cross Any Type Of Water As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the", "through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if", "ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current", "you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.  Crossing Puddles, Pools, Flooded Areas Or Other Standing Water Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it", "contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.  CAUTION: Muddy waters can reduce the cooling system effectiveness by depositing debris onto the radiator.  Driving Through Water Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing", "to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  CAUTION: Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be", "cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water Flowing water can be extremely dangerous.  Never attempt to cross a fast running stream or river even in shallow water.  Fast moving water can easily push your vehicle downstream, sweeping it out of control.  Even in very shallow water, a high current can still wash the dirt out from around your tires putting you and your vehicle in jeopardy.  There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the vehicle's running ground clearance.  You should never attempt to cross flowing water which is deeper than", "running ground clearance.  You should never attempt to cross flowing water which is deeper than the vehicle's running ground clearance.  Even the slowest current can push the heaviest vehicle downstream and out of control if the water is deep enough to push on the large surface area of the vehicle's body.  Before you proceed, determine the speed of the current, the water's depth, approach angle, bottom condition and if there are any obstacles.  Then cross at an angle heading slightly upstream using the low and slow technique.  WARNING: Never drive through fast moving deep water.  It can push your vehicle downstream, sweeping it out of control.  This could put you and your passengers at risk of injury or drowning.", "Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not", "had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  For normal service, periodic fluid level checks are not required.  When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected.  If gear oil leakage is suspected, inspect the fluid level.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within", "will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Intentional tampering with emissions control systems can result in civil penalties being assessed against you.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery", "not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m", "This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  EMISSIONS", "The I/M station can fail your vehicle because the MIL is on with the engine running.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not", "is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently", "is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button", "and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.", "Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a", "electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access,", "may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will", "and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to", "your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual", "increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.", "and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics", "All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48", "and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The", "vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This indicator light will illuminate for approximately two seconds when the ignition is turned to the ON/RUN position.  Its duration may be longer based on colder operating conditions.  Vehicle will not initiate start until telltale is no longer displayed.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in", "Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The message will stay active until the ignition is placed in the ON/RUN position.  Anti-Lock Brake System (ABS) Warning Light This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.", "in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The warning display will turn on indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The Air Bag Warning Light will turn on", "you if the light comes on again after initial startup.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  This warning light will illuminate when the Stop/Start system is not functioning properly and service is required.  Contact an authorized dealer for service.  This warning light monitors the ABS.  The light will turn on when the ignition is", "for service.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC", "Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.", "WARNING LIGHTS AND MESSAGES The warning/indicator lights will illuminate in the instrument panel together with a dedicated message and/or acoustic signal when applicable.  These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner\u2019s Manual, which you are advised to read carefully in all cases.  Always refer to the information in this chapter in the event of a failure indication.  All active telltales will display first if applicable.  The system check menu may appear different based upon equipment options and current vehicle status.  Some telltales are optional and may not appear.  Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which", "Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  Upper Center None Time Current Econ Compass Range to Empty Trip A Distance Audio Average Econ Trip B Distance Outside Temp Menu Title Speedometer Adjustable Upper Anchorage If the compression is increased too much on the front upper corner of the rear doors, deformation of the seal will occur.", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Apple CarPlay\u00ae.  Anywhere using your mobile device and Vehicle Branded App From your computer on the Owner\u2019s Site (not available on all functions) Contacting SiriusXM Guardian\u2122 Customer Care (not available on all functions) Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.", "function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control", "the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.", "and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  Android Auto\u2122", "command your vehicle.  Other operating systems may be supported in the future.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your", "You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Android Auto\u2122 allows you to access and stream your favorite music with apps like YouTube Music, iHeartRadio, and Spotify.  Using your smartphone\u2019s data plan, you can stream endless music on the road.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your", "its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be", "in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  While using Android Auto\u2122, Google Maps\u2122 provides voice-guided: Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used", "organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is", "to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.", "If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offIf the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and", "steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate", "Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  This warning light will turn on when there's a fault with the EPS system The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which", "instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offThe heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on", "only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Press the heated", "Light is illuminated, you could cause the clutch to overheat and cause a fire.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  When the SET (+) or the SET (-) button (located on the steering wheel) is pushed, the display will read \u201cACC SET.\u201d The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which", "instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d This warning light will turn on when there's a fault with the EPS system When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds,", "Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  Push the SWAY BAR switch to disconnect or connect the sway bar.  The Sway Bar Indicator Light (located in the instrument cluster) will illuminate when the bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when activation conditions are not met.  The stabilizer/sway bar", "during activation transition, or when activation conditions are not met.  The stabilizer/sway bar should remain in on-road mode during normal driving conditions.  The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.  If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.", "Materials Added To Fuel Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Designated TOP TIER Detergent Gasoline contains a higher level of detergents to further aide in minimizing engine and fuel system deposits.  When available, the usage of TOP TIER Detergent Gasoline is recommended.  Visit www.toptiergas.com for a list of top tier detergent gasoline retailers.  Indiscriminate use of fuel system cleaning agents should be avoided.  Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients.  These can harm fuel system gasket and diaphragm materials.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are", "gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels", "standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility", "performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  Methylcyclopentadienyl Manganese Tricarbonyl (MMT) In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasolines to increase octane.  Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT.  Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles.  The manufacturer recommends that gasoline without MMT be used in your vehicle.  The MMT content of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gasoline retailer whether the gasoline contains MMT.  MMT is prohibited in Federal law and California reformulated gasoline.", "UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch", "on the Uconnect system.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays", "When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Depending on the vehicle\u2019s options, feature settings may vary.  Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Depending on the vehicle\u2019s options, feature settings may vary.", "Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking", "engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the", "on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the", "interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy", "switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.", "This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48", "and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The", "vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This indicator light will illuminate for approximately two seconds when the ignition is turned to the ON/RUN position.  Its duration may be longer based on colder operating conditions.  Vehicle will not initiate start until telltale is no longer displayed.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in", "Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The message will stay active until the ignition is placed in the ON/RUN position.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the", "the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Seat Belt Reminder Warning Light This warning light indicates when the driver or passenger seat belt is unbuckled.  When the ignition is first placed in the ON/RUN or ACC/ON/RUN position and if the driver\u2019s seat belt is unbuckled, a chime will sound and the light will turn on.  When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound Service 4WD Warning Light \u2014 If Equipped This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it", "to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.", "Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts", "Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow", "the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down", "nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.", "the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive", "the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose", "If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.", "Green Indicator Lights 4WD Auto Indicator Light \"\u21e84WD Auto Indicator Light \u2014 If Equipped\" Front Fog Indicator Light \"\u21e8Front Fog Indicator Light \u2014 If Equipped\" Parking/Headlights On Indicator Light \"\u21e8Parking/Headlights On Indicator Light\" Stop/Start Active Indicator Light \"\u21e8Stop/Start Active Indicator Light \u2014 If Equipped\" Turn Signal Indicator Lights \"\u21e8Turn Signal Indicator Lights\" Rear Seat Belt Fastened Indicator Light \"\u21e8Rear Seat Belt Fastened Indicator Light \u2014 If Equipped With A Premium Instrument Cluster\" If equipped, the overhead console contains an ASSIST and an SOS button.  Center Light Status Description Off No call activated Green Active call in progress Red System error The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  Monitoring battery level status led light red 40% or lower yellow 40% to 70% green 70% to 100% electronic stability control", "status led light red 40% or lower yellow 40% to 70% green 70% to 100% electronic stability control (esc) active warning light \u2014 if equipped this warning light will indicate when the electronic stability control system is active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is", "the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.  Adaptive Cruise Control (ACC) Set Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.  Adaptive Cruise Control (ACC) Ready Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.", "Lumbar Support The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  Lumbar Support Control Knob Turning the temperature control knob clockwise increases the heating temperature and turning the temperature control knob counterclockwise decreases the heating temperature.  Lumbar Support The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  Heater Only Turning the temperature control knob clockwise increases the heating temperature and turning the temperature control knob counterclockwise decreases the heating temperature.", "Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Drag & Drop Menu Bar The Uconnect features and services in the main menu bar are easily customized for your preference.", "The Uconnect features and services in the main menu bar are easily customized for your preference.  Simply follow these steps: press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Note: This feature is only available if the vehicle is in PARK.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the", "to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the", "select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF", "one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.", "Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Install the belt rail on the rear of the vehicle.  Secure the belt rail using the six fasteners with the provided #T50 Torx head driver and ratchet.  Refer to the following table for recommended torque specifications.  Torque Specification For Torx Fastener Maximum Minimum 119.5 in-lb (13.5 N\u00b7m)", "specifications.  Torque Specification For Torx Fastener Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  Damage to the retainers will occur.  Step One Install the door frames.  Start with both front doors, followed by both rear doors.  Apply the appropriate torque specifications for the door frame Torx head fasteners Failure to follow the next steps could result in damage to the soft top or vehicle.  Unsnap and remove the storage bag.  This bag should be discarded.  It was intended as a protective cover for shipping only.  Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top onto the rear of the cab.  Line up the locater pins (one on each side of the soft top) with the rear door frames.  Step Four Using the provided #T50 Torx head driver and ratchet, install and tighten the Torx fasteners by turning them clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or", "clockwise.  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for recommended torque specifications.  Repeat on the opposite side.  Step Five Torque Specification For Torx Fasteners Maximum Minimum 119.5 in-lb (13.5 N\u00b7m) 150.5 in-lb (17.0 N\u00b7m) 106.2 in-lb (12.0 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Step Five Before driving the vehicle with the top in the Sunrider\u00ae position, ensure the top is secured with the provided hook-and-loop fasteners Step Six  Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the", "the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield,", "position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to", "door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The rear door frames must be removed first, followed by the front door frames.  Loosen (do not remove) the four bolts on the door hinges using the provided #T50 Torx head driver.  Hinge Bolt Locations Do not adjust the body mounted", "using the provided #T50 Torx head driver.  Hinge Bolt Locations Do not adjust the body mounted hinges, or any part of the door latch, as modifications to these parts will affect installation of the full door.  With the bolts loose, the door can be moved forward by pushing the door handle toward the front of the vehicle, and/or upward by grabbing the door handle and lifting towards the roof.  Once the gaps between the door and vehicle body are uniform around the entire door, tighten the door hinge bolts to 20.3 ft\u00b7 lb / 27.5 N\u00b7m (Max Torque: 27.3 ft\u00b7 lb / 37 N\u00b7m).  Lift upward on each section of the seat bottom.  Lift From Beneath Seat (Left Side Shown) Raise the seat bottom upward into the Stadium Position.  Stadium Position If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\"", "the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Determine which door is affected.  Open the affected door and hold a dollar-size piece of paper along the top of the door opening against the vehicle near where the leak/noise was observed.  Make sure half of the paper is above the area where the door seal contacts the door opening, while the other half is below.  Close the door on the paper, then pull the paper upward.  If the paper moves with little to no effort, the upper half-door will need to be adjusted in that area to increase seal compression.  Performing A Paper Test Push Upward On Middle Of Upper Half Door To Remove", "Rear Defrost Button Press and release the Rear Defrost Control button on the touchscreen, or push and release the button on the faceplate to turn on the rear window defroster and the heated outside mirrors (if equipped).  The Rear Defrost indicator illuminates when the rear window defroster is on.  The rear window defroster automatically turns off after 10 minutes.  CAUTION: Failure to follow these cautions can cause damage to the heating elements: Use care when washing the inside of the rear window.  Do not use abrasive window cleaners on the interior surface of the window.  Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.  Labels can be peeled off after soaking with warm water.  Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.  Keep all objects a safe distance from the window.  Heated Mirrors \u2014 If Equipped These mirrors are heated to melt frost or ice.  This feature will be activated whenever you turn on the", "mirrors are heated to melt frost or ice.  This feature will be activated whenever you turn on the rear window defroster (if equipped) \"\u21e8climate controls\" .  Winter Operation To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used.  Use of the Air Recirculation mode during Winter months is not recommended, because it may cause window fogging.", "Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash", "If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped", "and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the", "to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.", "The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and", "or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The", "to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo", "cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Hazard Warning Flashers Button The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when", "side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Warning CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks 1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If", "Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Hazard Warning Flashers Button With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not", "also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.  turn on the Hazard Warning Flashers.  Apply the parking brake firmly and shift an automatic transmission in PARK; a manual transmission to REVERSE.  Block the wheel diagonally opposite the wheel to be raised.  Never start or run the engine with the vehicle on a jack.  Do not", "opposite the wheel to be raised.  Never start or run the engine with the vehicle on a jack.  Do not let anyone sit in the vehicle when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.  Only use the jack in the positions indicated and for lifting this vehicle during a tire change.  If working on or near a roadway, be extremely careful of motor traffic.  To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.", "The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is", "an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will", "vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the", "battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as", "the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you", "a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.", "NEUTRAL (N) Use this range when the vehicle is standing for prolonged periods with the engine running.  Apply the parking brake and shift the transmission into PARK if you must exit the vehicle.  WARNING: Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.  These are unsafe practices that limit your response to changing traffic or road conditions.  You might lose control of the vehicle and have a collision.  CAUTION: Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle N (Neutral) Neutral \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicleWARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages", "without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  Five-position transfer case \u2014 if equipped the transfer case provides five positions: 2h (two-wheel drive high range) 4h auto (four-wheel drive auto high range) 4h part time (four-wheel drive part time high range) n (neutral) 4l (four-wheel drive low range) for additional information on the appropriate use of each transfer case position, see the following information:.  N (Neutral) Neutral \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicleWARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position", "or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  Neutral indicator light \u2014 if equipped this light alerts the driver that the vehicle is in the neutral mode \"\u21e8automatic transmission \u2014 if equipped\" .", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to", "this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before", "it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your", "flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.", "N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.  See Recreational Towing for further information WARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll,", "both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) NEUTRAL (N)  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.", "Apple CarPlay\u00ae Voice Command Apple CarPlay\u00ae allows you to use your voice to interact with Siri through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your iPhone\u00ae and a number of its apps onto your Uconnect touchscreen.  Connect your iPhone\u00ae 5 or higher to one of the media USB ports, using the factory-provided Lightning cable, and press the new Apple CarPlay\u00ae icon that replaces your Phone icon on the main menu bar to begin Apple CarPlay\u00ae.  Push and hold the vr button on the steering wheel, or press and hold the home button within apple carplay\u00ae, to activate siri, which recognizes natural voice commands to use a list of your iphone\u00ae features: phone music messages maps \u2014 if equipped additional apps \u2014 if equipped note: feature availability depends on your carrier and mobile phone maker.  Some Apple CarPlay\u00ae features may not be available in every region and/or language.  Note: Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered", "Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered in the US and other countries.  Apple\u00ae terms of use and privacy statements apply.  Apple carplay\u00ae apple carplay\u00ae \u00b9 use this qr code to access your digital experience.  Uconnect works seamlessly with Apple CarPlay\u00ae, the smarter, more secure way to use your iPhone\u00ae in the car, and stay focused on the road.  Use your Uconnect Touchscreen display, the vehicle's knobs and controls, and your voice with Siri to get access to Apple Music\u00ae, Maps, Messages, and more.  To use Apple CarPlay\u00ae, make sure you are using iPhone\u00ae 5 or later, have Siri enabled in Settings, ensure your iPhone\u00ae is unlocked for the very first connection only, and then use the following procedure: Connect your iPhone\u00ae to one of the media USB ports in your vehicle.  Note: be sure to use the factory-provided lightning cable that came with your phone, as aftermarket cables may not work.  Once the device is connected and recognized, the Phone icon on the", "cables may not work.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Apple CarPlay\u00ae Icon.  Note: apple carplay\u00ae is set to launch immediately.  You can also launch it by pressing the Apple CarPlay\u00ae icon on the touchscreen.  Apple carplay\u00ae and lte data coverage 1 \u2014 lte data coverage 2 \u2014 apple carplay\u00ae icon once apple carplay\u00ae is up and running on your uconnect system, the following features can be utilized using your iphone\u00ae data plan: phone music messages maps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Apple CarPlay\u00ae features may or may not be available in every region and/or language.  Note: To use Apple CarPlay\u00ae, make sure that cellular data is turned on, and that you are in an area with cellular coverage.  Your data and cellular coverage is shown on the left side of the radio screen.  Data plan rates apply.  Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Apple CarPlay\u00ae.  Anywhere using your mobile device and Vehicle Branded App From your computer on the Owner\u2019s Site (not available on all functions) Contacting SiriusXM Guardian\u2122 Customer Care (not available on all functions) Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.", "function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Closing The Hood To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.", "rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  WARNING: Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.", "The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d  The obd ii system may not be ready if your vehicle was", "Diagnostic System (OBD II) Cybersecurity\u201d  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully", "Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  ONLY an authorized service technician should connect equipment", "that the system is now ready.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.", "The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the", "is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine", "To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the", "of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going", "it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.", "Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Vehicle must be at a stop and the gear selector", "windshield is raised prior to installing the tops.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Release both of the outside hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  1 \u2014 Pull For Windshield Washer 2 \u2014 Rotate For Wiper Operation 3 \u2014 Push Up For Mist The driver's seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.", "can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat.  Pull upward on the handle to raise the seat, push downward on the handle to lower the seat.  Several strokes may be necessary to achieve the desired position.  FOLDING WINDSHIELD The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element provides.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Raise", "low range operation preferred if you are driving off-road with the windshield folded down.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  WARNING: Carefully follow these warnings to help protect against personal injury: Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from", "before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshieldUsing the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.", "the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Cleaning Instructions During windshield down applications, dust/dirt can accumulate in the cover and block the camera lens.  Use a microfiber cloth to clean the camera lens, module, and inside cover, being careful not to damage or scratch the module.", "Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  If you get hung up or high-centered on an object,", "jacking on locations other than those indicated.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.", "get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand,", "brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Preparations For Jacking Park on a firm, level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side", "level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  Turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers should not remain in the vehicle when the vehicle is being jacked in position.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn", "alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals:", "the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.", "indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this", "oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Secondary Method For Oil Change Reset Procedure Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Note: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.  If necessary, repeat this procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take", "change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the", "necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.", "Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may", "the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Priming If The Engine Has Run Out Of Fuel \u2014 Diesel Engine Add a substantial amount of fuel to the tank, approximately 2 to 5 gal (8 L to 19 L).  Push ignition switch twice without your foot on brake to put vehicle in RUN position.  This will activate the in tank fuel pump for approximately 30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure", "30 seconds.  Repeat this process twice.  Start the engine using the Normal Starting procedure WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  CAUTION: The starter motor will engage for approximately 30 seconds at a time.  Allow two minutes between cranking intervals.  Note: The engine may run rough until the air is forced from all the fuel lines.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel.  CAUTION: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Note: Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are", "pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Bulk Fuel Storage \u2014 Diesel Fuel If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  If the vehicle will not start see Note: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system.  WARNING: Do not open the high pressure fuel system with the engine running.  Engine operation causes high fuel pressure.  High pressure fuel spray can cause serious injury or death.  If you store quantities of fuel, good maintenance of the stored fuel is also", "injury or death.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster", "ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void", "from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop", "due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If", "system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  Based on engine operation conditions, the oil change", "possible, within the next 500 miles (805 km).  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  Use only the manufacturer\u2019s recommended fluid For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type", "seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  See Engine Fluids and Lubricants for the correct engine oil viscositySynthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Lubricant should be approximately 1/8 inch (3 mm) below the bottom edge of the oil fill hole.  Use only the manufacturer\u2019s recommended fluid Trac-Lok is especially helpful during slippery driving conditions.  With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction.  Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure build-up or your tire pressure will be too low.  1 \u2014", "operation.  DO NOT reduce this normal pressure build-up or your tire pressure will be too low.  1 \u2014 Coolant Temperature 2 \u2014 Oil Temperature 3 \u2014 Battery Voltage 4 \u2014 Transmission Temperature 5 \u2014 Oil Pressure Operation in ambient temperature below 32\u00b0F (0\u00b0C) may require special considerations.  The following charts suggest these options:", "Description Family Drive Alerts help promote safer driving and give you peace of mind when your loved ones are out on the road.  You can set boundary limits, monitor driving speed, and pinpoint your vehicle\u2019s location any time, any place.  Use the vehicle branded app to set alerts: boundary alert receive a notification the moment your vehicle is driven either out of or into a geographic boundary that you set.  Curfew alert receive a notification when your car is being driven outside of the curfew time.  Speed alert receive a notification whenever your car exceeds a speed limit you set.  Valet alert receive a notification if and when your vehicle is driven outside a quarter-mile radius of a valet drop-off zone.  Event Data Recorder (EDR) This vehicle is equipped with an event data recorder (EDR).  The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle\u2019s systems", "or hitting a road obstacle, data that will assist in understanding how a vehicle\u2019s systems performed.  The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.  The edr in this vehicle is designed to record such data as: how various systems in your vehicle were operating; whether or not the driver and passenger safety belts were buckled/fastened; how far (if at all) the driver was pressing the accelerator and/or brake pedal; and, how fast the vehicle was traveling.  These data can help provide a better understanding of the circumstances in which crashes and injuries occur.  To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed.  In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.  Note: EDR data are recorded by your vehicle only if a", "they have access to the vehicle or the EDR.  Note: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are recorded.  However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full", "drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.", "When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.", "jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or", "with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash", "other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.", "connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the", "post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.", "Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Drag & Drop Menu Bar The Uconnect features and services in the main menu bar are easily customized for your preference.", "The Uconnect features and services in the main menu bar are easily customized for your preference.  Simply follow these steps: press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Note: This feature is only available if the vehicle is in PARK.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the", "to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the", "select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF", "one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.", "Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.  Do not open or close the Sunrider\u00ae top while driving.  Operating the top while driving could cause the driver to lose", "the Sunrider\u00ae top while driving.  Operating the top while driving could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.  Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the", "driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.  Safety Both underinflation and overinflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering.  WARNING: Improperly inflated tires are dangerous and can cause collisions.  Underinflation increases tire flexing and can result in overheating and tire failure.  Overinflation reduces a tire's ability to cushion shock.  Objects on the road and chuckholes can cause damage that result in tire failure.  Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.  Unequal tire pressures can cause steering problems.  You could lose control of your vehicle.  Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.  Always drive with each tire", "to the other can cause the vehicle to drift to the right or left.  Always drive with each tire inflated to the recommended cold tire inflation pressure.  Note: Unequal tire pressures from side to side may cause erratic and unpredictable steering response.  Unequal tire pressure from side to side may cause the vehicle to drift left or right.  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  Manual Mirror Adjustment If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  This feature allows you to tilt the steering column upward or", "or removal of an obstruction.  This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Ignoring the Rearview Mirror light could mean you will not have SOS Call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  When the vehicle is started,", "dealer service the Occupant Restraint Control system immediately.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  When cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on the mirror.", "ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemApple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is", "while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Depending on your vehicle\u2019s specifications, the USB port may contain playback capabilities and will allow you to play music from your smartphone device or USB devices through your vehicle\u2019s sound system.  1 \u2014 Reset Button 2 \u2014 Battery Status Button 3 \u2014 Service/Diagnostic Port (Non-charging, Non-customer use port) 4 \u2014 Type A USB Charging Port 5 \u2014 Battery Status LED 6 \u2014 Speaker Charging Port 7 \u2014 AUX Port The Smart Charging USB ports provide power to your device up to an hour after the vehicle is turned off.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and", "may need to access this information to assist with the diagnosis and service of your vehicle and emissions system WARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your", "technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.", "Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking", "engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch", "and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center", "Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Dimmer Control The dimmer control is part of the", "illuminated cupholders, and front door handles).  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).", "Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers", "to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to", "may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.", "The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  Do Not Use Mechanical Key  Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.  Your vehicle is", "comes as an assembly, and is not removable.  This can damage the silicone shield.  Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic", "subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be", "Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "Lowering the soft top \u00b9 use this qr code to access your digital experience.  If your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  The Sunrider\u00ae soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.  The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When", "if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so", "in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being", "be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx", "the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a", "electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access,", "may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will", "and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key", "unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the", "floor are removed.  Locking Storage Bin If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  Inside the bin are three removable dividers to set up storage that works best for you.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Console Storage Compartment The center console has both an", "the bin to the floor are removed.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove", "Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  Your Locking Storage Bin also has a front handle that makes it easier to carry and pull out from the floor of the vehicle when the four bolts that attach the bin to the floor are removed.  Locking Storage Bin (Closed View) Locking Storage Bin", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive", "are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.", "If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature", "whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  If the vehicle is overheating, it will need to be serviced by an authorized dealer.  If the light turns on while driving, safely pull", "will need to be serviced by an authorized dealer.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for serviceIn unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If you continue operating", "four minutes or until the engine is able to cool; whichever comes first.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  Do not open hot engine cooling system.", "pedal and repeat the \u201cNormal Starting\u201d procedure.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If", "headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this", "engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure.  This could damage your engine.  Engine misfiring or vibrating severely Sudden loss of power Unusual engine noises Fuel, oil or coolant leaks Sudden change, outside the normal operating range, in the engine operating temperature Excessive smoke Oil pressure drop If there is a malfunction in the Stop/Start system, the system will not shut down the", "pressure drop If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display", "Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  Engine start-up in very low ambient temperature", "time.  Wait 10 to 15 seconds before trying again.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant", "a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.", "Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center", "or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside", "of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument", "the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup", "cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside", "ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all", "preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls,", "Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a", "brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Transporting Pets Air Bags deploying in the front seat could harm your pet.  An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.  Pets should be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using", "stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the", "or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.", "Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the", "form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background", "for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold", "cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by", "the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Get started the", "have incoming text messages read out loud, and place and receive hands-free calls.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.", "Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not", "Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed", "system going into a stop/start ready state under more extreme conditions of the items listed previously.  Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.", "Jack Location The jack and tools are stored under the right rear seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat.  Removing the wing bolt release the tool bag straps from the jack and remove tools from bag.  Jack and tool bag remove tool kit and assemble tools.  Jack And Tool Bag There are two ways to assemble the tools: Note: If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  CAUTION: The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools,", "and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools, always reinstall them in the original carrier and location.  While driving you may experience abrupt stopping, rapid acceleration or sharp turns.  A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an", "being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Gasoline instrument clusters gasoline instrument clusters \u00b9 use this qr code to access your digital experience.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the", "moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  WARRANTY INFORMATION See the Warranty Information for the terms and provisions of FCA US LLC warranties applicable to this vehicle and market.  Refer to www.mopar.com/om for further information.  See the Warranty Information for the terms and provisions of FCA Canada Inc. warranties applicable to", "the Warranty Information for the terms and provisions of FCA Canada Inc. warranties applicable to this vehicle and market.  Refer to www.owners.mopar.ca/en for further information.  Use this QR code to access your digital experience.", "If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  To close the tailgate, lift upward until both sides latch into place.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Tailgate In Mid Position If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable", "If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To use the mid position, open the tailgate and lower it to near mid position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  The tailgate is dampened to provide a slower, more controlled lowering.  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the", "If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.", "What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage", "check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any", "hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Safety Guidelines Please read this manual carefully before using the system.  It contains instructions on how to use the system in a safe and effective manner.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision", "applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is", "it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Hazard Warning Flashers Button The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF", "the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Warning CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut", "CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks 1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button", "If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is", "center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator,", "After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough", "not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is", "an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed", "Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the", "you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or", "with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of", "and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match", "Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl", "or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  To ensure proper engine lubrication, the engine oil must be maintained at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Check engine oil level Check windshield washer fluid level Check the tire pressures and look for unusual wear or", "oil level Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage Check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed Check function of all interior and exterior lights  Fluid Level Check Check the fluid level by removing the fill plug.  The fluid level should be between the bottom of the fill hole and a point not more than 3/16 of an inch (4.76 mm) below the bottom of the hole.  Add fluid, if necessary, to maintain the proper level.", "Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the", "code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire full size spare \u2014 if equipped the full size spare is for temporary emergency use only.  This tire may look like", "\u2014 if equipped the full size spare is for temporary emergency use only.  This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not.  This spare tire may have limited tread life.  When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced.  Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity.  Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Rim Size This is the rim size that is appropriate for the tire size listed.  Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle.  Replacement tires must be equal to the load capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h,", "capacity of this tire size.  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the", "to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire.", "Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  Do Not Use Mechanical Key  Key Fob Your vehicle is", "compartments (if equipped), and rear seatbacks.  Do Not Use Mechanical Key  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be", "may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .", "To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries", "system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster", "in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.", "active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely", "in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.", "The warning display will turn on indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN", "on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  This warning light will illuminate when the Stop/Start system is not functioning properly and service is required.  Contact an authorized dealer for service.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The", "is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has", "ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use", "to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The red Brake System Warning Light will turn on when", "and may stay on for as long as four seconds.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  This warning light will", "dealer as soon as possible to have the problem diagnosed and corrected.  This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however,", "If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This indicator light will illuminate for approximately two seconds when the ignition is turned to the ON/RUN position.  Its duration may be longer based on colder operating conditions.  Vehicle will not initiate start until telltale is no longer displayed.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning", "The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The message will stay active until the ignition is placed in the ON/RUN position.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Preparations For Jacking Park on a firm, level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking", "operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers should not remain in the vehicle when the vehicle is being jacked in position.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating", "not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.", "When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  After fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged.  If the system detects a malfunction, the \u201cgASCAP\u201d message will display in the odometer display.  Tighten the gas cap until a \"clicking\" sound is heard.  This is an indication that the gas cap is properly tightened.  Push the odometer reset button to turn the message off.  If the problem persists, the message will appear the next time the vehicle is started.  This might indicate a damaged cap.  If the problem is detected twice in a row, the system will turn on the MIL.  Resolving the problem will turn the MIL off.  The fuel", "in a row, the system will turn on the MIL.  Resolving the problem will turn the MIL off.  The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Fuel System Messages The following chart contains a list of different messages that may appear in the instrument cluster, depending on different system or fuel conditions.  Use the descriptions to interpret what the message means and determine the best action to take.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it", "the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d This warning light will turn on when there's a fault with the EPS system When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive", "Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  Push the SWAY BAR switch to disconnect or connect the sway bar.  The Sway Bar Indicator Light (located in the instrument cluster) will illuminate when the bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when", "bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when activation conditions are not met.  The stabilizer/sway bar should remain in on-road mode during normal driving conditions.  The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.  If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.", "Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  Bumper end caps are removable on steel bumpers only.  The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 Bolt #2 Remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Before completing the following steps: if your vehicle", "Repeat this procedure on the other side.  Before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step Two 1 \u2014 Hex Bolt Cover Installed 2 \u2014 Hex Bolt Cover Removed Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting", "trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step Six Secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Do Not Overtighten!  Damage to the windshield could result.  Open the fuel filler door.  Fuel Filler Door Remove the fuel cap by rotating it counterclockwise.  Fuel Filler Cap Fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  Lowering the windshield before", "gasoline nozzle, reinstall fuel cap and close the fuel filler door.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx", "the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to", "(two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the", "the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.", "Soft Top Rear Window Storage Bag \u2014 If Equipped To safely store the soft top rear window, proceed as follows: With the bag opened completely, fold the fabric divider downward and lay the rear window in the bottom of the bag.  Step one fold the divider upward, covering the rear window.  Step two lay the first quarter panel cover assembly all the way to the right side and the second quarter panel cover assembly on the left side.  Secure both using the two hook-and-loop fastener straps on each side.  Note: the quarter panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step three 1 \u2014 left quarter panel cover assembly 2 \u2014 right quarter panel cover assembly close the storage bag and store in a safe location.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert", "latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward", "in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store", "Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal", "that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior", "header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush", "the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.", "Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet", "clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.  Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for", "front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Rear Carpet Remove the grommets under the front seat (one left and one right).  Carpet split then pull the carpet out, to the rear and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin (if equipped), by removing the four bolts that hold it to the floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and", "floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then lift the assembly out from under the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear retainers remove carpet from the vehicle.  When reinstalling the carpet, perform these steps in reverse order making sure that the carpet is tucked under the scuffs, B-pillar, console, and then refasten the grommets.  Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket", "Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS", "or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress", "the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.", "The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Retrieve funnel from under the right rear seat.  Fuel Funnel Location Refueling Funnel Remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting Funnel Ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from", "an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel", "the clutch to overheat and cause a fire.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners", "for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not", "has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners Loosen the fasteners from the engine air cleaner filter cover using a suitable tool.  Engine Air Cleaner Filter Cover 1 \u2014 Fasteners 2 \u2014 Engine Air Cleaner Filter Cover Lift the engine air cleaner filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from the housing assembly.  engine air cleaner filter cover  The vehicle may be equipped with a refueling funnel.  Vehicles", "engine air cleaner filter cover  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  The engine may be switched off even if the warning light is on: repeated interruptions of the regeneration process could cause an early deterioration of engine oil.  For this reason it is always advisable to wait for the symbol to go off before turning off the engine, following the previously mentioned instructions.  Do not complete the DPF regeneration process when the vehicle is stopped.  See the following steps for refueling: Emergency Gas Can Refueling Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil", "periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.", "Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering", "pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode", "process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  In following situations the engine will not stop: driver\u2019s seat belt is not", "if they are fulfilled.  In following situations the engine will not stop: driver\u2019s seat belt is not buckled outside temperature is less than 10\u00b0f (\u201312\u00b0c) or greater than 109\u00b0f (43\u00b0c) actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode engine has not reached normal operating temperature battery is discharged when driving in reverse hood is open transfer case is in 4l or n (neutral) driver's seat is not occupied or driver door is open vehicle is at high altitude the vehicle is on a steep grade forward gear is engaged steering angle is beyond threshold system fault is present hvac is set to max a/c it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  To Start The Engine While In Autostop Mode When the gear selector is in NEUTRAL, the engine will start when the clutch pedal is pressed (does not require", "selector is in NEUTRAL, the engine will start when the clutch pedal is pressed (does not require complete/full pedal press).  The vehicle will go into STOP/START SYSTEM NOT READY mode until the vehicle speed is greater than 5 mph (8 km/h).  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  In following situations the engine will not stop: driver\u2019s seat belt is not buckled outside temperature is less than 10\u00b0f (\u201312\u00b0c) or greater than 109\u00b0f (43\u00b0c) actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode engine has not reached normal operating temperature battery is discharged when driving in reverse hood is open transfer case is in 4l or n (neutral) driver's seat is not occupied or driver door is open vehicle is at high altitude the vehicle is on a steep grade forward gear is engaged steering angle is beyond threshold system fault is", "is on a steep grade forward gear is engaged steering angle is beyond threshold system fault is present hvac is set to max a/c it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Possible Reasons The Engine Does", "to normal, turn the engine off immediately and call for service Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed", "(neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the", "menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING:", "display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and", "mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Rear Seat Unoccupied Indicator Light \u2014 If Equipped This light indicates when the rear passenger seats are unoccupied, and will illuminate in the upper right portion of the instrument cluster display, momentarily replacing the configurable corner information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the", "information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed", "mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the", "vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR", "clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected", "time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "Shifting Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  To engage REVERSE gear from the NEUTRAL position, lift the REVERSE ring, located below the knob and move the gear selector all the way left and then forward.  If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the", "the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  To shift the gears, fully press the clutch pedal and place the gear selector into the desired gear position (the diagram for the engagement of the gears is displayed on the handle of the selector).  The gear position will be displayed in the instrument cluster.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle", "all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If You Stall Or Begin To Lose Headway If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill", "immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If", "or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.", "AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic mode \"\u21e8automatic operation\" .  A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass,", "through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  To Deactivate A soft tap on the brake pedal, pushing the CANC (cancel) button, or normal brake pressure while slowing the vehicle will deactivate the Cruise Control without erasing the set speed from memory.  The following conditions will also deactivate the cruise control without erasing the set speed from memory: vehicle parking brake is applied stability event occurs gear selector is moved out of drive engine overspeed occurs clutch pedal is pressed (manual transmission only) vehicle is operating at a low rpm (manual transmission only) pushing the on/off button or placing the ignition", "operating at a low rpm (manual transmission only) pushing the on/off button or placing the ignition in the off position, erases the set speed from memory.  Recirculation Button Push the Recirculation button on the faceplate to change the system between recirculation mode and outside air mode.  The Recirculation indicator and the A/C indicator (if equipped) illuminate when the Recirculation button is pressed.  Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.  Recirculation can be used in all modes except for Defrost.  Recirculation may be unavailable if conditions exist that could create fogging on the inside of the windshield.  The A/C can be deselected manually without disturbing the mode control selection.  Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur.  Extended use of this mode is not recommended.  On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode", "On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode to improve window clearing operation.  Recirculation is disabled automatically if this mode is selected.  Attempting to use Recirculation while in this mode causes the LED on the control button to blink and then turn off.  A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or", "the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.", "Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical", "illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.  It may cause burns even at low temperatures, especially if used for long periods of time.  Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion.  This may cause the seat heater to overheat.  Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  The engine must be running for the heated steering wheel to operate.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle", "Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme", "HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating", "screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred,", "on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offThe heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will", "wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Press the", "Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  When the SET (+) or the SET (-) button (located on the steering wheel) is pushed, the display will read \u201cACC SET.\u201d The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.", "AUX/USB Control The Media Hub is located on the instrument panel, below the climate controls.  Behind the media hub access door, the Media Hub contains one AUX port, a Type C USB port and one standard USB port.  Both USB ports allow you to play music from smartphones or USB devices through the vehicle\u2019s sound system.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or The Smart Charging USB ports provide power to your device up to an hour after the vehicle is turned off.  For example, if a device is plugged into the Type A USB port and another device is plugged into the Type C USB port, a message will appear and allow you to select which device to use.  Located inside the center console, a second USB port allows you to only charge USB devices.  Depending on your vehicle\u2019s specifications, the USB port may contain playback capabilities and will allow you to play music from", "the USB port may contain playback capabilities and will allow you to play music from your smartphone device or USB devices through your vehicle\u2019s sound system.  A third and fourth USB port are located behind the center console, above the power inverter.  Both ports are charge only.  When a new device or smartphone is plugged into the USB ports, one of the following message will display depending on the device being utilized: \u201cA new device is now connected.  Previous connection was lost\u201d.  \u201c(Phone Name) now connected.  Previous connection was lost\u201d.  \u201cAnother device is in use through the same USB port.  Please disconnect the first device to use the second device\u201d.  Note: Once a device is connected to the USB port, it will begin charging and is ready for use with the system.  Type C and Type A charge-only USB ports can be used at the same time but cannot be used simultaneously while playing media.  When both Type C and Type A charge-only USB ports are in use they will be charged at a reduced rate.  Both ports", "C and Type A charge-only USB ports are in use they will be charged at a reduced rate.  Both ports share a single data connection.  The user cannot switch between Type A and Type C. Note: Charge unsupported devices with the Charge Only USB ports.  If an unsupported device is plugged into a Media USB port, a message will display on the touchscreen that the device is not supported by the system.  WARNING: Do not plug in or remove the external device while driving.  Failure to follow this warning could result in a collision.  Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions systemWARNING: ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service", "connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The Media Hub is located on the instrument panel, below the climate controls.  Behind the media hub access door, the Media Hub contains one AUX port, a Type C USB port and one standard USB port.  Both USB ports allow you to play music from smartphones or USB devices through the vehicle\u2019s sound system.  A third and fourth USB port are located behind the center console, above the power inverter.  Both ports are charge only.  Located inside the center console, a second USB port allows", "inverter.  Both ports are charge only.  Located inside the center console, a second USB port allows you to only charge USB devices.  AUX/USB Control The Media Hub is located on the instrument panel, below the climate controls.  Behind the media hub access door, the Media Hub contains one AUX port, a Type C USB port and one standard USB port.  Both USB ports allow you to play music from smartphones or USB devices through the vehicle\u2019s sound system.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or The Smart Charging USB ports provide power to your device up to an hour after the vehicle is turned off.  For example, if a device is plugged into the Type A USB port and another device is plugged into the Type C USB port, a message will appear and allow you to select which device to use.  Located inside the center console, a second USB port allows you to only charge USB", "device to use.  Located inside the center console, a second USB port allows you to only charge USB devices.  Depending on your vehicle\u2019s specifications, the USB port may contain playback capabilities and will allow you to play music from your smartphone device or USB devices through your vehicle\u2019s sound system.  A third and fourth USB port are located behind the center console, above the power inverter.  Both ports are charge only.  When a new device or smartphone is plugged into the USB ports, one of the following message will display depending on the device being utilized: \u201cA new device is now connected.  Previous connection was lost\u201d.  \u201c(Phone Name) now connected.  Previous connection was lost\u201d.  \u201cAnother device is in use through the same USB port.  Please disconnect the first device to use the second device\u201d.  Note: Once a device is connected to the USB port, it will begin charging and is ready for use with the system.  Type C and Type A charge-only USB ports can be used at the same time but cannot be", "the system.  Type C and Type A charge-only USB ports can be used at the same time but cannot be used simultaneously while playing media.  When both Type C and Type A charge-only USB ports are in use they will be charged at a reduced rate.  Both ports share a single data connection.  The user cannot switch between Type A and Type C. Note: Charge unsupported devices with the Charge Only USB ports.  If an unsupported device is plugged into a Media USB port, a message will display on the touchscreen that the device is not supported by the system.  WARNING: Do not plug in or remove the external device while driving.  Failure to follow this warning could result in a collision.", "Fuel Filler Cap The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Open the fuel filler door.  Fuel filler door remove the fuel cap by rotating it counterclockwise.  Fuel filler cap fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the", "is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light (MIL) to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  CAUTION: Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Note: When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure", "tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  After fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged.  If the system detects a malfunction, the \u201cgASCAP\u201d message will display in the odometer display.  Tighten the gas cap until a \"clicking\" sound is heard.  This is an indication that the gas cap is properly tightened.  Push the odometer reset button to turn the message off.  If the problem persists, the message will appear the next time the vehicle is started.  This might indicate a", "persists, the message will appear the next time the vehicle is started.  This might indicate a damaged cap.  If the problem is detected twice in a row, the system will turn on the MIL.  Resolving the problem will turn the MIL off.  The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal", "the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the", "belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure", "One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners Loosen the fasteners from the engine air cleaner filter cover using a suitable tool.  Engine Air Cleaner Filter Cover 1 \u2014 Fasteners 2 \u2014 Engine Air Cleaner Filter Cover Lift the engine air cleaner filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from the housing assembly.  engine air cleaner filter cover", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside", "are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts", "the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when", "20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set", "ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speed  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed", "show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which", "sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to", "will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Hazard Warning Flashers Button The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the", "or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Warning CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks 1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all", "Button  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Hazard Warning Flashers Button With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit", "the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.  turn on the Hazard Warning Flashers.  Apply the parking brake firmly and shift an automatic transmission in PARK; a manual transmission to REVERSE.  Block the wheel diagonally opposite the wheel to be raised.  Never start or run the engine with the vehicle on a jack.  Do not let anyone sit in the vehicle when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get", "when it is on a jack.  Do not get under the vehicle when it is on a jack.  If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.  Only use the jack in the positions indicated and for lifting this vehicle during a tire change.  If working on or near a roadway, be extremely careful of motor traffic.  To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.", "Green Indicator Lights 4WD Auto Indicator Light \"\u21e84WD Auto Indicator Light \u2014 If Equipped\" Front Fog Indicator Light \"\u21e8Front Fog Indicator Light \u2014 If Equipped\" Parking/Headlights On Indicator Light \"\u21e8Parking/Headlights On Indicator Light\" Stop/Start Active Indicator Light \"\u21e8Stop/Start Active Indicator Light \u2014 If Equipped\" Turn Signal Indicator Lights \"\u21e8Turn Signal Indicator Lights\" Rear Seat Belt Fastened Indicator Light \"\u21e8Rear Seat Belt Fastened Indicator Light \u2014 If Equipped With A Premium Instrument Cluster\" If equipped, the overhead console contains an ASSIST and an SOS button.  Center Light Status Description Off No call activated Green Active call in progress Red System error The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  The warning display will turn on indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE", "turn on indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light", "as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  This warning light will illuminate when the Stop/Start system is not functioning properly and service is required.  Contact an authorized dealer for service.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will", "ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles", "light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  To enter the \u201cPartial Off\u201d mode, momentarily push the ESC OFF button and the ESC OFF Indicator Light will illuminate.  To turn the ESC on again, momentarily push the ESC OFF button and the ESC OFF Indicator Light will turn off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  The Automatic Headlight System will turn the headlights on or off according to ambient light levels.  To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation.  When the system is on, the headlight time delay", "the last detent for automatic headlight operation.  When the system is on, the headlight time delay feature is also on.  This means the headlights will stay on for up to 90 seconds (programmable through the uconnect settings \"\u21e8uconnect settings\" ) after you place the ignition into the off position.  To turn the automatic system off, move the headlight switch out of the AUTO position.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will", "signal indicator will flash independently and the corresponding exterior turn signal lamps will flash.  Turn signals can be activated when the multifunction lever is moved down (left) or up (right).  Reduce power to unnecessary loads if possible: Turn off redundant lights (interior or exterior) Check what may be plugged in to power outlets +12 Volt, 115 Volts AC, USB ports Check HVAC settings (blower, temperature) Check the audio settings (volume) When the Lights button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s exterior and interior lights.  When the \u201cDaytime Running Lights\u201d feature is selected, the daytime running lights can be turned on or off.  This feature is only allowed by law in the country of the vehicle purchase.  Depending on the vehicle\u2019s options, feature settings may vary.  Can someone else locate my vehicle?  Your vehicle may be located by anyone who has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.", "has your PIN and access to your account.  It is your responsibility to guard your PIN accordingly.  See the Uconnect and SiriusXM Guardian\u2122 terms of service for more information.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pushing the red Panic button.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the", "I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.", "come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with", "in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with", "in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off", "reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper", "this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow", "can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling", "pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does", "Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.", "Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak", "a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by", "or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake", "If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light", "ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service", "comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.", "on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system", "on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt", "booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light", "to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.", "When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  All cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Remove the two screws that pass through the bed sheet metal.  Tail Lamp Screws Pull the", "(136 kg).  Remove the two screws that pass through the bed sheet metal.  Tail Lamp Screws Pull the outboard side of the lamp rearward, far enough to unsnap the two receptacles on the outboard side of the lamp housing, from the two plastic snap post retainers in the outer box side panel.  Once removed, locate and rotate the appropriate socket a quarter turn counterclockwise, then remove it from the housing.  Pull the bulb straight from the socket to replace.  To install a new bulb, reverse the procedure above.  With the bag opened completely, fold the fabric divider downward and lay the rear window in the bottom of the bag.  Step One Fold the divider upward, covering the rear window.  Step Two Lay the first quarter panel cover assembly all the way to the right side and the second quarter panel cover assembly on the left side.  Secure both using the two hook-and-loop fastener straps on each side.  The quarter panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step Three 1 \u2014", "panel cover assemblies are marked \u201c1\u201d and \u201c2\u201d on the inside of the panel assembly.  Step Three 1 \u2014 Left Quarter Panel Cover Assembly 2 \u2014 Right Quarter Panel Cover Assembly Close the storage bag and store in a safe location.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the", "boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover", "latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Three-Position Tailgate The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  Ensure the tailgate strap is properly seated behind the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid", "the circular retainer against the sides of the sheet metal.  When hauling cargo using the mid position and the tailgate, you must support the load at two forward locations: at the top of the rear wheelhouse (1) between the wheelhouse and the tailgate (2) chamfered boards in pickup box 1 \u2014 support location 1 2 \u2014 support location 2 note: failure to support the load at these two forward locations could result in damage.  Three 2x4 boards are needed to provide support at locations (1) and (2).  Each board will need to be cut to fit inside the pickup box.  The support at location (1) should be seated in the dedicated formation on top of the wheelhouses.  The support at location (2) should use the remaining two 2x4s.  Stack the boards and place them into the formation in the side wall of the pickup box.  The corners of the bottom board will need to be chamfered to fit.  Note: all cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).", "Rear Wall Storage Bin To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  Note: The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  Non-Locking Storage Wall The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  There is also an option to remove the wall by removing the four bolts that connect the storage wall to the floor.  Rear Wall Storage Bin To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  Note: The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of", "secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  Rear Wall Storage Bin The Locking Storage Bin can be removed by unfastening the four bolts that attach the bin to the vehicle floor using the provided #40 Torx head driver and ratchet.  The bottom of the storage bin has rubber mats that need to be removed to access the four bolts.  These bolts can then be stored in the fastener bin below the rear seat.  If equipped, the Locking Storage Bin is located below the rear seats.  It can be accessed by folding the rear seat bottom upward into the Stadium Position.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.", "Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light", "Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  The red Brake System Warning Light will", "ON/RUN mode, have the light repaired as soon as possible.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer", "a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  This warning light will turn on when there's a fault with the EPS system  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning", "If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and", "to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a", "of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.", "Materials Added To Fuel Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  Designated TOP TIER Detergent Gasoline contains a higher level of detergents to further aide in minimizing engine and fuel system deposits.  When available, the usage of TOP TIER Detergent Gasoline is recommended.  Visit www.toptiergas.com for a list of top tier detergent gasoline retailers.  Indiscriminate use of fuel system cleaning agents should be avoided.  Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients.  These can harm fuel system gasket and diaphragm materials.  Out of Gas/Fuel Delivery Drivers cannot always count on a gas station being nearby, especially when traveling away from home.  We will dispatch a service provider to deliver a small", "especially when traveling away from home.  We will dispatch a service provider to deliver a small amount of fuel (maximum two gallons) to get you to a nearby station.  This service is limited to two occurrences in a 12-month period.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel", "operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the", "is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine", "clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you", "good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  Open the fuel filler door.  Fuel Filler Door Remove the diesel fuel filler cap by rotating it counterclockwise.  Fuel and Diesel Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the", "Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the vehicle with fuel.  When the nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel filler door.", "There may also be a second 115 V (400 W) maximum exterior power inverter located on the rear right side of the truck bed near the tailgate.  This inverter can be turned on by the Instrument Panel Power Inverter switch located to the left of the steering wheel.  This inverter can power cellular phones, electronics and other low power devices requiring power up to 400 W. Certain video game consoles exceed this limit, as will most power tools.  The indicator light on the power inverter switch will be illuminated when the inverter is turned on.  Exterior Truck Bed Power Inverter (If Equipped) A third and fourth USB port are located behind the center console, above the power inverter.  Both ports are charge only.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.", "of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's", "not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Power Inverters \u2014 If Equipped There is a 115 V (400 W) maximum inverter outlet located on the back of the center console to convert Direct Current (DC) to Alternating Current (AC).  This outlet can power cellular", "console to convert Direct Current (DC) to Alternating Current (AC).  This outlet can power cellular phones, electronics and other low power devices requiring power up to 400 W. Certain video game consoles exceed this power limit, as will most power tools.  There may also be a second 115 V (400 W) maximum exterior power inverter located on the rear right side of the truck bed near the tailgate.  This inverter can be turned on by the Instrument Panel Power Inverter switch located to the left of the steering wheel.  This inverter can power cellular phones, electronics and other low power devices requiring power up to 400 W. Certain video game consoles exceed this limit, as will most power tools.  The indicator light on the power inverter switch will be illuminated when the inverter is turned on.  The power inverter is designed with built-in overload protection.  If the power rating of 400 W is exceeded, the power inverter automatically shuts down.  Once the electrical device has been removed from the outlet,", "inverter automatically shuts down.  Once the electrical device has been removed from the outlet, the inverter should automatically reset.  Note: 400 W is the maximum for the inverter, not each outlet.  If two outlets are in use, 400 W is shared among the devices plugged in.  Note: The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is", "the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's", "not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage.", "Rear door removal rear door removal \u00b9 use this qr code to access your digital experience.  To remove the rear doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nuts from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin under the rear seat.  Hinge pin nut slide the front seat(s) fully forward.  Pry open and remove the plastic wiring access door from the bottom of the B-pillar.  Wiring access door unplug the wiring connector.  Note: squeeze the tab on the base of the wiring harness.  This will unlock the connector tab, allowing the wiring connector to be unplugged.  Unhook the wire harness strap from the hook on the body side.  Store the wire connector in the lower basket of the door.  Wiring connector with the door in the open position, remove the check bolt from the door check attachment on the body (using a #t40 torx head driver).  Note: keep the check arm in the extended position", "on the body (using a #t40 torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  To reinstall the door(s), perform the previous steps in the reverse order.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened", "to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  WARNING: To avoid personal injury be sure to keep your arms, hands, fingers and all objects clear of the check arm area during the removal and installation procedures.  Note: The upper hinge has a longer pin, which can be used to assist in guiding the door into place when reinstalling.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Front door removal front door removal \u00b9 use this qr code to access your digital experience.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement", "on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  To remove the front doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nut from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin located under the rear seat.  Hinge pin nut remove the plastic wiring access door under the instrument panel by sliding the plastic panel along the door frame toward the seats until the tabs are detached.  Wiring access door note: do not force open; this will break the plastic cover.  Pull up on the red locking tab to unlock the wiring harness.  Closed wiring harness 1 \u2014 red locking tab 2 \u2014 wiring harness lever (closed position) push and hold down the black security tab under the wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014", "the wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014 wiring harness lever (open position) 2 \u2014 black security tab with the wiring harness open, pull straight downward on the wiring connector to unplug.  Store the wiring connector in the lower door basket.  With the door in the open position, remove the check screw from the door check attachment on the body side (using a #T40 Torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  See note below if the check arm gets pushed into the door while the door is off.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.", "operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Note: When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door", "Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.", "Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  WARNING: Fast spinning tires can be dangerous.  Forces generated by excessive wheel speeds may cause tire damage or failure.  A tire could explode and injure someone.  Do not spin your vehicle's wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.  Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering,", "may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive", "safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand,", "brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be", "may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades seeCAUTION: Never use Non-Detergent Oil or", "occur.  For the recommended viscosity and quality grades seeCAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy", "significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.", "Biodiesel Fuel Properties \u2014 Low Ambient Temperatures Biodiesel fuel may gel or solidify at low ambient temperatures, which may pose problems for both storage and operation.  Precautions can be necessary at low ambient temperatures, such as storing the fuel in a heated building or a heated storage tank, or using cold temperature additives.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  Biodiesel fuel may gel or solidify at low ambient temperatures, which may pose problems for both storage and operation.  Precautions can be necessary at low ambient temperatures, such as storing the fuel in a heated building or a heated storage tank, or using cold", "temperatures, such as storing the fuel in a heated building or a heated storage tank, or using cold temperature additives.  Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended.  Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up", "in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.", "Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers", "tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.", "Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.  Adaptive Cruise Control (ACC) Ready Indicator Light \u2014 If Equipped With a Premium Instrument Cluster This light will turn on when the vehicle equipped with Adaptive Cruise Control (ACC) has been turned on, but not set.  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speedCruise Control SET Indicator Light \u2014 If Equipped With A Base Instrument Cluster This indicator light will illuminate when the cruise control is set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but", "Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  This indicator will illuminate when the hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety", "slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  This indicator will illuminate when the hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant", "hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully", "to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Release both of the outside hood latches.", "Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  If the \u201cSERVICE POWER STEERING\u201d", "Normal operation will resume once the system is allowed to cool.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function.  However, the effort required to brake the vehicle will be much greater than that required with the power system operating.  If the stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the", "stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not attempt to drive the vehicle over 18 mph (29 km/h).  Driving faster than 18 mph (29 km/h) with a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  When the condition that deactivated the system is no longer present, the system will return to the \u201cAdaptive Cruise Control Off\u201d state and will resume function by simply reactivating it.  There may be situations where the Hill Start Assist (HSA) will not activate and slight rolling may occur, such as on minor hills or with a loaded vehicle, or while pulling a trailer.  HSA is not a substitute for active driving involvement.  It is always the", "while pulling a trailer.  HSA is not a substitute for active driving involvement.  It is always the driver\u2019s responsibility to be attentive to distance to other vehicles, people, and objects, and most importantly brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision or serious personal injury.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized", "on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off CAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial", "it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  ELECTRO-HYDRAULIC POWER STEERING Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may", "are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offCAUTION: Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  Note: Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.", "Off-Road Driving Tips  Soft sand is very difficult to travel through with full tire pressure.  When crossing soft, sandy spots in a trail, maintain your vehicle's momentum and do not stop.  The key to driving in soft sand is using the appropriate tire pressure, accelerating slowly, avoiding abrupt maneuvers and maintaining the vehicle's momentum.  If you are going to be driving on large soft sandy areas or dunes, reduce your tire pressure to a minimum of 15 psi (103 kPa) to allow for a greater tire surface area.  Reduced tire pressure will drastically improve your traction and handling while driving on the soft sand, but you must return the tires to normal air pressure before driving on pavement or other hard surfaces.  Be sure you have a way to reinflate the tires prior to reducing the pressure.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass,", "proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and", "left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  Sand Soft sand is very difficult to travel through with full tire pressure.  When crossing soft, sandy spots in a trail, maintain your vehicle's momentum and do not stop.  The key to driving in soft sand is using the appropriate tire pressure, accelerating slowly, avoiding abrupt maneuvers and maintaining the vehicle's momentum.  If you are going to be driving on large", "abrupt maneuvers and maintaining the vehicle's momentum.  If you are going to be driving on large soft sandy areas or dunes, reduce your tire pressure to a minimum of 15 psi (103 kPa) to allow for a greater tire surface area.  Reduced tire pressure will drastically improve your traction and handling while driving on the soft sand, but you must return the tires to normal air pressure before driving on pavement or other hard surfaces.  Be sure you have a way to reinflate the tires prior to reducing the pressure.  CAUTION: Reduced tire pressures may cause tire unseating and total loss of air pressure.  To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneuvers.", "US/CANADA Exposure to Radio Frequency Radiation The radiated output power of the internal wireless radio is far below the FCC and IC radio frequency exposure limits.  Nevertheless, the wireless radio will be used in such a manner that the radio is 8 inches (20 cm) or further from the human body.  The internal wireless radio operates within guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community.  The radio manufacturer believes the internal wireless radio is safe for use by consumers.  The level of energy emitted is far less than the electromagnetic energy emitted by wireless devices such as mobile phones.  However, the use of wireless radios may be restricted in some situations or environments, such as aboard airplanes.  If you are unsure of restrictions, you are encouraged to ask for authorization before turning on the wireless radio \"\u21e8general information\" .  Vehicle body care requirements vary according to geographic locations and", "\"\u21e8general information\" .  Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for", "the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.", "extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking", "others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.  The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window", "switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  Power Window Switches Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.  Window Lockout Switch The window lockout switch allows you to disable the window controls on the rear passenger doors.  To disable the window controls, rotate the switch", "the window controls on the rear passenger doors.  To disable the window controls, rotate the switch downward.  To enable the window controls, rotate the switch upward.", "Speedometer push and release the up or down arrow button until the speedometer menu icon is displayed in the instrument cluster display.  Push and release the ok button to toggle between mph and km/h.  Instrument cluster descriptions tachometer indicates the engine speed in revolutions per minute (rpm x 1000).  Caution: do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature gauge the temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle", "boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Caution: driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument cluster display the instrument cluster display features a driver interactive display.  Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer indicates vehicle speed.  Speedometer push and release the up or down arrow button until the speedometer menu icon is displayed in the instrument cluster display.  Push and release the ok button to toggle between mph and km/h.", "in the instrument cluster display.  Push and release the ok button to toggle between mph and km/h.  Favorite menus speedometer vehicle info off road \u2014 if equipped (show/hide) driver assist \u2014 if equipped (show/hide) fuel economy (show/hide) trip info (show/hide) stop / start \u2014 if equipped audio (show/hide) messages screen setup vehicle settings \u2014 if equipped.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by", "operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will", "will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer", "driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display If an obstacle is detected in the center front region, the display will show a single solid arc in the center front region with no chime.  As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and a fast sound tone will be heard and will change from fast, to continuous.", "Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go", "At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting", "and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine", "Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable", "battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain", "could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Secondary Battery", "booster pack, follow the manufacturer's operating instructions and precautions.  Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.", "Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact", "background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected,", "will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text", "allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press", "6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a", "Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.", "Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel", "only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damageIf climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  FUEL REQUIREMENTS \u2013 DIESEL ENGINE Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway", "Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good", "using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  WARNING: Do not use alcohol or gasoline as a fuel blending agent.  They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel.  CAUTION: If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filter(s) to avoid engine damage Diesel Fuel Specifications This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine", "tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Fuel Operating Range *Number 1 ULSD Fuel should only be used where extended arctic conditions 0\u00b0F (-18\u00b0C) exist.  Note: use ultra low sulfur diesel (ulsd) fuels only.  Note: Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump", "at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).", "To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to", "equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed", "Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster Vehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.", "After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle", "or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  FOUR\u2013WHEEL DRIVE OPERATION WARNING: Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the", "of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Transmission function is monitored electronically for abnormal conditions.  If a condition is detected that could result in transmission damage, Transmission Limp Home mode is activated.  In this mode, the transmission may operate only in certain gears, or may not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some situations, the transmission may not re-engage if the engine is turned off and restarted.  The Malfunction Indicator Light (MIL) may be illuminated.  A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary.  It is important to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only manufacturer's specified transmission fluid It is important to maintain the transmission fluid at the correct level using the", "fluid It is important to maintain the transmission fluid at the correct level using the recommended fluid.  Using a transmission fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  Using a lower gear while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  This action will also provide better engine braking.  Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission", "or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing a heavy trailer), use the AutoStick shift control to select a lower gear Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels", "\u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  During cold weather, you may experience increased effort in shifting until the transmission fluid warms up.  This is normal.  Routine fluid and filter changes are not required.  However, change the fluid and filter if the fluid becomes contaminated (with water, etc.  ), or if the transmission is disassembled for any reason.", "It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Even if power steering assistance is no longer operational, it is still possible to steer the vehicle.  Under these conditions there will be a substantial increase in", "possible to steer the vehicle.  Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.  If the condition persists, see an authorized dealer for service.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering assistance in order to prevent damage to the system.  Normal operation will resume once the system is allowed to cool.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster", "If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function.  However, the effort required to brake the vehicle will be much greater than that required with the power system operating.  If the stabilizer/sway bar will not return to on-road mode, the Sway Bar Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not", "Indicator Light will flash in the instrument cluster and vehicle stability may be reduced.  Do not attempt to drive the vehicle over 18 mph (29 km/h).  Driving faster than 18 mph (29 km/h) with a disconnected stabilizer/sway bar may contribute to the loss of vehicle control, which could result in serious injury.  When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  When the condition that deactivated the system is no longer present, the system will return to the \u201cAdaptive Cruise Control Off\u201d state and will resume function by simply reactivating it.  There may be situations where the Hill Start Assist (HSA) will not activate and slight rolling may occur, such as on minor hills or with a loaded vehicle, or while pulling a trailer.  HSA is not a substitute for active driving involvement.  It is always the driver\u2019s responsibility to be attentive to distance to other", "driving involvement.  It is always the driver\u2019s responsibility to be attentive to distance to other vehicles, people, and objects, and most importantly brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision or serious personal injury.  Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control.  You could have a collision.  Do not drive the vehicle unless the transfer case is fully engaged.  Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension", "of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.", "ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster displayIt provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.  The ParkSense Park Assist system provides visual and audible indications of the distance between the rear and/or front fascia/bumper and a detected obstacle when backing up or moving forward (e.g.  during a parking maneuver).  For system limitations and usage precautions, see ParkSense will turn off the Front Park Assist audible alert (chime) after approximately three seconds when an obstacle has been detected, the vehicle is stationary, and the brake pedal is applied.  ParkSense can be active only when the gear selector is in REVERSE or DRIVE.  If ParkSense is enabled at one of these gear selector positions, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above.  A warning will appear in the instrument cluster", "to approximately 7 mph (11 km/h) or above.  A warning will appear in the instrument cluster display indicating the vehicle is above ParkSense operating speed.  The system will become active again if the vehicle speed is decreased to less than approximately 6 mph (9 km/h).  The ParkSense Warning screen is located within the instrument cluster display It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.  ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles.  Parking curbs might be temporarily detected or not detected at all.  Obstacles located above or below the sensors will not be detected when they are in close proximity.  The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected.  It is recommended that the driver looks over his/her shoulder when using ParkSense.  Setting Name Description Forward Collision", "looks over his/her shoulder when using ParkSense.  Setting Name Description Forward Collision Warning Sensitivity This setting will change the distance at which the Forward Collision Warning (FCW) alert sounds.  The \u201cMedium\u201d setting will have the FCW system signal when an object is in view, and the possibility of a collision is detected.  The \u201cNear\u201d setting will have the FCW system signal when the object is closer to the vehicle.  The \u201cFar\u201d setting will have the FCW system signal when an object is at a far distance from the vehicle.  Forward Collision Warning This setting will turn the Forward Collision Warning system on or off.  The \u201cOff\u201d setting will deactivate the FCW system.  The \u201cWarning Only\u201d setting will provide only an audible chime when a collision is detected.  The \u201cWarning + Active Braking\u201d setting will provide an audible chime and apply some brake pressure when a collision is detected.  ParkSense This setting will change the type of ParkSense alert when a close object is detected and can provide", "setting will change the type of ParkSense alert when a close object is detected and can provide both an audible chime and a visual display when an object is detected.  Front ParkSense Volume This setting adjusts the volume of the Front ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Rear ParkSense Volume This setting adjusts the volume of the Rear ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Blind Spot Alert This setting will change the type of alert provided when an object is detected in a vehicle\u2019s blind spot.  The \u201cOff\u201d setting will turn off Blind Spot Alert.  The \u201cLights\u201d setting will activate the Blind Spot Alert lights on the outside mirrors.  The \u201cLights & Chime\u201d setting will activate both the lights on the outside mirrors and an audible chime.  Hill Start Assist This setting will turn the Hill Start Assist system on or off.  ParkView Backup Camera Active Guidelines This setting will turn the ParkView Backup Camera Active Guidelines on or off.", "Active Guidelines This setting will turn the ParkView Backup Camera Active Guidelines on or off.  ParkView Backup Camera Delay This setting will add a timed delay to the ParkView Backup Camera when shifting out of REVERSE.  Fixed ParkView Backup Camera Guidelines This setting will turn the Fixed ParkView Backup Camera Guidelines on or off.  Front Camera Gridlines This setting will turn the Front Camera Gridlines on or off.  Tire Fill Assist This setting will turn Tire Fill Assist on or off.  ParkSense Sensors The four ParkSense sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 79 inches (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.  The six ParkSense sensors, located in the front fascia/bumper, monitor the area in front of the vehicle that is within the sensors\u2019 field of view.", "fascia/bumper, monitor the area in front of the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 47 inches (120 cm) from the front fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.", "Fuel Filler Cap The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  Open the fuel filler door.  Fuel filler door remove the fuel cap by rotating it counterclockwise.  Fuel filler cap fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the", "is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light (MIL) to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  CAUTION: Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Note: When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure", "tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque", "cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern", "torque specifications for the door frame fasteners.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step One The fasteners will not fall out once completely loose, as they are held in place by design.  Step One Lift the frame upward, removing it from the vehicle.  Step Two Store the fasteners in a secure location.  Repeat the procedure on the front door frame.  1 \u2014 Corner Fasteners 2 \u2014 Rear Fasteners Loosen the fasteners from the engine air cleaner filter cover using a suitable tool.  Engine Air Cleaner Filter Cover 1 \u2014 Fasteners 2 \u2014 Engine Air Cleaner Filter Cover Lift the engine air cleaner filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from", "filer cover to access the engine air cleaner filter.  Remove the engine air cleaner filter from the housing assembly.  engine air cleaner filter cover  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Tighten the fuel filler cap about a quarter turn until you hear one click.  This is an indication that the cap is properly tightened.  If the fuel filler cap is not tightened properly, the MIL will come on.  Be sure the cap is tightened every time the vehicle is refueled.  After fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged.  If the system detects a malfunction, the \u201cgASCAP\u201d message will display in the odometer display.  Tighten the gas cap until a \"clicking\" sound is heard.  This is an indication that the gas cap is properly tightened.  Push the odometer reset button to turn the message off.  If the problem persists, the message will appear the next time the vehicle is started.  This might indicate", "persists, the message will appear the next time the vehicle is started.  This might indicate a damaged cap.  If the problem is detected twice in a row, the system will turn on the MIL.  Resolving the problem will turn the MIL off.  The fuel filler cap is located on the left side of the vehicle.  To access the fuel filler cap, push on the fuel filler door to unlatch it.  To close the fuel filler door, push on it a second time.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.", "Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the", "is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your", "with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.  Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove", "the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Rear Carpet Remove the grommets under the front seat (one left and one right).  Carpet split then pull the carpet out, to the rear and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin (if equipped), by removing the four bolts that hold it to the floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then lift the assembly out from under the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear retainers remove", "the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear retainers remove carpet from the vehicle.  When reinstalling the carpet, perform these steps in reverse order making sure that the carpet is tucked under the scuffs, B-pillar, console, and then refasten the grommets.  Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach", "and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to", "check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.", "Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be", "Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire dealer or original", "those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result", "what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw", "accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Tire pressures change by approximately 1 psi (7 kPa) per 12\u00b0F (7\u00b0C) of air temperature change.  Keep this in mind when checking tire pressure inside a garage, especially in the Winter.  Jacking and tire changing \u00b9 use this qr code to access your digital experience.  Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: At Every Oil Change Interval As Indicated By Oil Change Indicator System: Change oil and filter.  Rotate the tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on.  Inspect battery and clean and tighten terminals as required.", "the oil indicator system turns on.  Inspect battery and clean and tighten terminals as required.  Inspect the CV/Universal joints.  Inspect brake pads, shoes, rotors, drums, hoses and parking brake.  Inspect engine cooling system protection and hoses.  Inspect exhaust system.  Inspect engine air cleaner filter if using in dusty or off-road conditions, replace engine air cleaner filter if necessary.  Inspect all door latches for presence of grease, reapply if necessary.  Do not continue driving with one or more flat tires as handling may be compromised.  Stop the vehicle, avoiding sharp braking and steering.  If a tire puncture occurs, repair immediately using the dedicated tire repair kit and contact an authorized dealer as soon as possible.  Consult an authorized tire dealer for tire repairs and additional information.  In the Selectable Tire Fill Alert application, which is located in the apps menu of the Uconnect system, you will be able to select a pressure setting for both the front and rear axle tire", "system, you will be able to select a pressure setting for both the front and rear axle tire pressures by scrolling through a pressure range from XX to 15 psi in 1 psi increments for each axle setting.  After inspecting or adjusting the tire pressure, always reinstall the valve stem cap.  This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.  Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under", "slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.", "4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  Yellow indicator lights 4wd indicator light \"\u21e84wd indicator light \u2014 if equipped\" 4wd low indicator light \"\u21e84wd low indicator light \u2014 if equipped\" 4wd part time indicator light \"\u21e84wd part time indicator light \u2014 if equipped\" axle locker fault indicator light \"\u21e8axle locker fault indicator light \u2014 if equipped\" rear axle lock indicator light \"\u21e8rear axle lock indicator light \u2014 if equipped\" front and rear axle lock indicator light \"\u21e8front and rear axle lock indicator light \u2014 if equipped\" forward collision warning off indicator light \"\u21e8forward collision warning off indicator light \u2014 if equipped\" neutral indicator light \"\u21e8neutral indicator light \u2014 if equipped\" sway bar indicator light \"\u21e8sway", "neutral indicator light \"\u21e8neutral indicator light \u2014 if equipped\" sway bar indicator light \"\u21e8sway bar indicator light \u2014 if equipped\" off road+ indicator light \"\u21e8off road+ indicator light \u2014 if equipped\" cargo light on indicator light \"\u21e8cargo light on indicator light\" wait to start indicator light \"\u21e8wait to start indicator light \u2014 if equipped\" low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \"\u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped\" water in fuel indicator light \"\u21e8water in fuel indicator light \u2014 if equipped\" selec speed control (ssc) indicator light \u2014 if equipped this light will turn on when selec speed control is activated.  Selec Speed Control is available in 4WD Low ONLY.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear", "forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  4WD Low Indicator Light \u2014 If Equipped This light alerts the driver that the vehicle is in the 4WD Low mode.  The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.  Low range provides a greater gear reduction ratio to provide increased torque at the wheels.  Yellow indicator lights 4wd indicator light  \u21e84wd indicator light \u2014 if equipped  4wd low indicator light  \u21e84wd low indicator light \u2014 if equipped  4wd part time indicator light  \u21e84wd part time indicator light \u2014 if equipped  axle locker fault indicator light  \u21e8axle locker fault indicator light \u2014 if equipped  rear axle lock indicator light  \u21e8rear axle lock indicator light \u2014 if equipped  front and rear axle lock indicator light  \u21e8front and rear axle lock indicator light \u2014 if equipped  forward collision warning off indicator light", "and rear axle lock indicator light \u2014 if equipped  forward collision warning off indicator light  \u21e8forward collision warning off indicator light \u2014 if equipped  neutral indicator light  \u21e8neutral indicator light \u2014 if equipped  sway bar indicator light  \u21e8sway bar indicator light \u2014 if equipped  off road+ indicator light  \u21e8off road+ indicator light \u2014 if equipped  cargo light on indicator light  \u21e8cargo light on indicator light  wait to start indicator light  \u21e8wait to start indicator light \u2014 if equipped  low diesel exhaust emissions additive adblue\u00ae (urea) indicator light  \u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped  water in fuel indicator light  \u21e8water in fuel indicator light \u2014 if equipped  green indicator lights 4wd auto indicator light  \u21e84wd auto indicator light \u2014 if equipped  front fog indicator light  \u21e8front fog indicator light \u2014 if equipped  parking/headlights on indicator light  \u21e8parking/headlights on indicator light  stop/start active indicator light  \u21e8stop/start", "light  \u21e8parking/headlights on indicator light  stop/start active indicator light  \u21e8stop/start active indicator light \u2014 if equipped  turn signal indicator lights  \u21e8turn signal indicator lights  rear seat belt fastened indicator light.", "Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  Jacking and tire changing jacking and tire", "by jacking on locations other than those indicated.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a", "only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended", "make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using", "a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review", "installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can", "jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.", "DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  What Causes Corrosion?  Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.  The most common causes are: road salt, dirt and moisture accumulation stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.", "stone and gravel impact.  Insects, tree sap and tar.  Salt in the air near seacoast localities.  Atmospheric fallout/industrial pollutants.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as", "similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody", "and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the", "child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.", "ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be", "may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 DIESEL ENGINE (IF EQUIPPED) The diesel engine does not require a break-in period due to its construction.  Normal operation is allowed, providing the following recommendations are followed: Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality", "conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Note: Light duty operation such as light trailer towing or no load operation will extend the time before the engine is at full efficiency.  Reduced fuel economy and power may be seen at this time.  Introduction To Connected Vehicle Services One of the many benefits of your vehicle\u2019s Uconnect system is that you can now take advantage of SiriusXM Guardian\u2122 connected services.  To unlock the full potential of SiriusXM Guardian\u2122 in your vehicle, you first need to activate SiriusXM Guardian\u2122 connected services.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Only use and interact with the features and applications when it is safe to do so.  Failure to follow these warnings can result in a collision and death or serious personal injury.", "Failure to follow these warnings can result in a collision and death or serious personal injury.  Note: SiriusXM Guardian\u2122 involves the collection, transmission and use of data from your vehicle  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use", "operations will occur.  For the recommended viscosity and quality grades see CAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  ENGINE BREAK-IN RECOMMENDATIONS \u2014 GASOLINE ENGINE (IF EQUIPPED) A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.  Drive moderately during the first 300 miles (500 km).  After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.  While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.  Wide-open throttle acceleration in low gear can be detrimental and should be avoided.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes", "in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For the recommended viscosity and quality grades seeCAUTION: Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.  Note: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.", "Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the", "windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the", "EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engineThis allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined", "is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact.  Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.  This feature notifies the user when the placard tire pressure is attained while inflating or deflating the tire.  Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.", "can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof", "to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  The functions described are for when the Jeep\u00ae wireless speaker is undocked from the vehicle.  When plugged into the docking station, the Jeep\u00ae wireless speaker functions as part of the vehicle\u2019s sound system.  The Jeep\u00ae wireless speaker is IP67 waterproof certified with design in mind to withstand rainfall, waterjets, splashing and being submerged in up to 3 ft (1 m) of water for up to 30 minutes.", "N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.  See Recreational Towing for further information WARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll,", "both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) NEUTRAL (N)  You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  N (Neutral) N (Neutral) \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicle.", "To ensure proper engine lubrication, the engine oil must be maintained at the correct level.  Check the oil level at regular intervals, such as every fuel stop.  The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.  Check engine oil level Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage Check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed Check function of all interior and exterior lights  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or", "oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  The engine oil filter should be replaced with a new filter at every engine oil change.  A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.", "Window Lockout Switch The window lockout switch allows you to disable the window controls on the rear passenger doors.  To disable the window controls, rotate the switch downward.  To enable the window controls, rotate the switch upward.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to", "A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  Power Door Lock Switch Push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone Push the lock button on the key fob.", "Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact.  Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.  This feature notifies the user when the placard tire pressure is attained while inflating or deflating the tire.  Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.", "can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof", "to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  The functions described are for when the Jeep\u00ae wireless speaker is undocked from the vehicle.  When plugged into the docking station, the Jeep\u00ae wireless speaker functions as part of the vehicle\u2019s sound system.  The Jeep\u00ae wireless speaker is IP67 waterproof certified with design in mind to withstand rainfall, waterjets, splashing and being submerged in up to 3 ft (1 m) of water for up to 30 minutes.", "Transmission Temperature Warning Light \u2014 If Equipped This warning light will illuminate to warn of a high transmission fluid temperature.  This may occur with strenuous usage such as trailer towing.  If this light turns on, stop the vehicle and run the engine at idle or slightly faster, with the transmission in PARK (P) or NEUTRAL (N), until the light turns off.  Once the light turns off, you may continue to drive normally.  If Manual transmission equipped, this warning will illuminate to warn of high clutch temperature.  This may occur with driver misuse of clutch pedal or resting foot on the clutch pedal or partially engaging the clutch for longer duration.  If the light turns on, it will be with an additional CLUTCH HOT message.  Stop the vehicle safely and run the engine at idle with transmission gear in NEUTRAL (N) until the light turns off.  Once the light turns off, follow the message displayed in the instrument cluster.  WARNING: If you continue operating the vehicle when the Transmission Temperature", "cluster.  WARNING: If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  CAUTION: Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the", "is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is", "the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not", "illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  In", "Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure.  This could damage your engine.  Engine misfiring or vibrating severely Sudden loss of power Unusual engine noises Fuel, oil or coolant leaks Sudden change, outside the normal operating range, in the engine", "noises Fuel, oil or coolant leaks Sudden change, outside the normal operating range, in the engine operating temperature Excessive smoke Oil pressure drop If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  Vehicle info push and release the up or down arrow button until the vehicle info menu icon is displayed in the instrument cluster display.  Push and release the left or right arrow button to scroll through the information submenus and push and release the ok button to select or reset the resettable submenus.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is", "information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  Service Forward Collision Warning (FCW) Light \u2014 If Equipped This warning light will illuminate to indicate a fault in the Forward Collision Warning System.  Contact an authorized dealer for service Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable", "is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.", "Component fluid, lubricant, or genuine part automatic transmission \u2013 if equipped use only mopar\u00ae zf 8 & 9 speed atf automatic transmission fluid or equivalent.  Failure to use the correct fluid may affect the function or performance of your transmission.  Manual transmission \u2013 if equipped we recommend using mopar\u00ae atf+4 automatic transmission fluid.  Transfer case we recommend using mopar\u00ae atf+4 automatic transmission fluid.  Front axle differential we recommend using mopar\u00ae gear & axle lubricant (sae 75w85) (api gl-5).  Rear axle differential (m220 sales codes dre/drf) we recommend using mopar\u00ae gear & axle lubricant (sae 75w85) (api gl-5).  Models equipped with Trac-Lok Limited Slip Differential require a friction modifier additive.  Brake master cylinder we recommend using mopar\u00ae dot 3 brake fluid, sae j1703.  Power steering reservoir we recommend using mopar\u00ae electric steering pump fluid.  Synthetic Engine Oils Your engine was designed for synthetic engine oils, only use synthetic API approved engine", "Oils Your engine was designed for synthetic engine oils, only use synthetic API approved engine oils.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Component Fluid, Lubricant, or Genuine Part Automatic Transmission \u2013 If Equipped Use only Mopar\u00ae ZF 8 & 9 Speed ATF Automatic Transmission Fluid or equivalent.  Failure to use the correct fluid may affect the function or performance of your transmission.  Manual", "to use the correct fluid may affect the function or performance of your transmission.  Manual Transmission \u2013 If Equipped We recommend using Mopar\u00ae ATF+4 Automatic Transmission Fluid.  Transfer Case We recommend using Mopar\u00ae ATF+4 Automatic Transmission Fluid.  Front Axle Differential We recommend using Mopar\u00ae Gear & Axle Lubricant (SAE 75W85) (API GL-5).  Rear Axle Differential (M220 Sales Codes DRE/DRF) We recommend using Mopar\u00ae Gear & Axle Lubricant (SAE 75W85) (API GL-5).  Models equipped with Trac-Lok Limited Slip Differential require a friction modifier additive.  Brake Master Cylinder We recommend using Mopar\u00ae DOT 3 Brake Fluid, SAE J1703.  Power Steering Reservoir We recommend using Mopar\u00ae Electric Steering Pump Fluid.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and", "gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or", "width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013", "load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire if a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: the gvwr is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured", "(one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 What is the phone number for roadside assistance call?  The phone number is: US: 1-800-521-2779 Canada: 1-800-363-4869 If I am subscribed to SiriusXM Guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance?  No, however your new vehicle may include Roadside Assistance Call services.  Setting Name Description Voice Response Length This setting will change the response length for the Voice Recognition system.  The \u201cBrief\u201d setting provides a shortened audio description from the system.  The \u201cDetailed\u201d setting provides the full audio description from the system.", "from the system.  The \u201cDetailed\u201d setting provides the full audio description from the system.  Show Command List This setting will allow you to turn the Command List on or off.  The \u201cAlways\u201d setting will always show the Command List.  The \u201cWith Help\u201d setting will show the Command List and provide a brief description of what the command does.  The \u201cNever\u201d setting will turn the Command List off.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is", "provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer", "OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the", "prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).", "Cruise control set indicator light \u2014 if equipped with a premium instrument cluster this indicator light will illuminate when the cruise control is set to the desired speed \"\u21e8cruise control\" .  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speedCruise Control SET Indicator Light \u2014 If Equipped With A Base Instrument Cluster This indicator light will illuminate when the cruise control is set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Base Instrument Cluster This light will turn on when cruise control has been turned on, but not set.  Cruise Control Ready Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This light will turn on when the cruise control has been turned on, but not set.  Adaptive Cruise", "This light will turn on when the cruise control has been turned on, but not set.  Adaptive Cruise Control (ACC) Ready Indicator Light \u2014 If Equipped With a Premium Instrument Cluster This light will turn on when the vehicle equipped with Adaptive Cruise Control (ACC) has been turned on, but not set.", "Vehicle Identification Number Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.  VEHICLE IDENTIFICATION NUMBER (VIN) The VIN is found on the left front corner of the A-pillar, visible from outside of the vehicle through the windshield.  Note: It is illegal to remove or alter the VIN plate.  Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle", "driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.", "Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic modeENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch", "features.  Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the Autostop function will be disabled Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the Autostop function will be disabled When Seats & Comfort/Auto-On Comfort Systems button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s comfort systems when remote start has been activated or the vehicle has been started.  Depending on the vehicle\u2019s options, feature settings may vary.  This system offers a full complement of manual override features.  The AUTO symbol in the front ATC display will be turned off when the system is being used in the manual mode.  When the Safety/Driving Assistance button is", "off when the system is being used in the manual mode.  When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Depending on the vehicle\u2019s options, feature settings may vary.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  When the AUX button is pressed on the touchscreen, the system displays the options related to the four vehicle AUX switches: Depending on the vehicle\u2019s options, feature settings may vary.  AUTO", "the four vehicle AUX switches: Depending on the vehicle\u2019s options, feature settings may vary.  AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic modeWhen Seats & Comfort/Auto-On Comfort Systems button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s comfort systems when remote start has been activated or the vehicle has been started.  Note: depending on the vehicle\u2019s options, feature settings may vary.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on", "vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons  AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic mode \"\u21e8automatic operation\" .", "There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.  Ensure that the socket is fully engaged on the lug nut/bolt (do not insert it halfway).  The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch", "be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly With the help of a second person, set the Sunrider\u00ae top onto the top of the vehicle making sure to align the holes at the front and rear of the side rails.  Lower Sunrider\u00ae Onto The Vehicle Swing the front frame bracket around the side of the rail, and insert the door rail attachment bolt (provided bolt without spacer) from underneath.  Tighten with a #40 Torx head driver until snug.  Attach Front Door Rail Bolt Insert the rear door rail attachment bolt (provided bolt with spacer) from underneath.  Tighten with #40 Torx head driver until snug.  Attach Rear Door Rail Bolt Repeat steps 3 and 4 on the other side of the vehicle.  The recommended torque specification for the front and rear door rail attachment bolts is 8.8 ft-lb (12 N\u00b7m).  Attach the rear clamp at the rear center of the Sunrider\u00ae top", "bolts is 8.8 ft-lb (12 N\u00b7m).  Attach the rear clamp at the rear center of the Sunrider\u00ae top using the two provided rear clamp attachment bolts.  Tighten with #40 Torx head driver until snug.  Rear Clamp Location The recommended torque specification for the rear clamp attachment bolts is 3.7 ft-lb (5 N\u00b7m).  From inside the vehicle, lift and pull the Sunrider\u00ae top forward using the integrated handle on the front header of the top.  Manually guide the top into the closed position.  Push Sunrider\u00ae Top Forward From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Pull the handle back upward while squeezing the hook, locking the latch into place.  Repeat on the other side.  Engage Both Header Latches Lug Nut/Bolt Torque **Lug Nut/Bolt Size Lug Nut/Bolt Socket Size 130 ft-lb (176 N\u00b7m) M14 x 1.50 mm 22 mm After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.  There are two nuts", "to be sure that all the lug nuts/bolts are properly seated against the wheel.  There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  To reinstall the door(s), perform the previous steps in the reverse order.  Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so", "in reverse order.  When reinstalling the interior soft trim panel: Be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  Prior to off-road usage, the side steps should be removed to prevent damage.  There are two nuts connecting to the body side and one bolt connecting to the underbody on each attachment bracket.  There are four attachment brackets on each side step.  Fastener Locations (One Side) Remove two nuts and one bolt from the underside of the vehicle for each of the four brackets.  Repeat for other side of vehicle.  Underside Nuts After all bolts and nuts have been removed, pull the side step assembly off of the vehicle.  To reinstall the side steps align the studs to the body side holes and fasten all nuts on all four brackets.  Then secure all four bolts to the underbody.  Repeat the reassembly procedure for the other side.  Prior to off-road usage, the side steps should be removed to prevent", "procedure for the other side.  Prior to off-road usage, the side steps should be removed to prevent damage.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step", "panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.", "The instrument cluster display will return to the last display selected after five seconds of no ACC display activity.  The instrument cluster display will return to the last display selected after five seconds of no ACC display activity.  Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.  The instrument cluster", "the specific information you want to make selections and adjustments.  The instrument cluster display will show the current ACC system settings.  The instrument cluster display is located in the center of the instrument cluster.  The information it displays depends on ACC system status.  When the system is turned on and in the ready state, the instrument cluster displays \u201cACC Ready.\u201d The instrument cluster display features a driver interactive display When the system is off, the instrument cluster displays \u201cAdaptive Cruise Control (ACC) Off.\u201d If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.  If the problem is not solved, a specific message will appear on the Instrument Cluster Display whenever a certain threshold is reached until it will no longer be possible to start the engine.  The instrument cluster display displays the current ACC system settings.  The information displayed depends on ACC system status.  INSTRUMENT", "current ACC system settings.  The information displayed depends on ACC system status.  INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.  ACC SET When ACC is set, the set speed will display in the instrument cluster.  The acc screen may display once again if any acc activity occurs, which", "in the instrument cluster.  The acc screen may display once again if any acc activity occurs, which may include any of the following: system cancel driver override system off acc proximity warning acc unavailable warning note: the instrument cluster display will return to the last display selected after five seconds of no acc display activity.  INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the", "your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.  Adaptive Cruise Control Ready When ACC is activated but the vehicle speed setting has not been selected, the display will read \u201cAdaptive Cruise Control Ready.\u201d Push the SET + or the SET - button (located on the steering wheel), and the following will display in the instrument cluster display.", "TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your", "And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  To close the tailgate, lift upward until both sides latch into place.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to", "this caution could damage the hard top.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before", "it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your", "flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.", "The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  Power Door Lock Switch Push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob", "door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone Push the lock button on the key fob.  INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.", "Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the", "form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited", "This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system", "of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use", "or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling,", "to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Engine Idling Avoid prolonged idling.  Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely.  Incomplete combustion allows carbon and varnish to form on piston rings, cylinder head valves, turbocharger, and injector nozzles.  Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying", "this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced", "a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that", "Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.", "Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.  Stationary Objects And Vehicles ACC does not react to stationary objects or vehicles.  For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane.  It will consider this stopped vehicle a stationary object as it did not previously detect movement from it.  Always be attentive and ready to apply the brakes if necessary.  The ACC screen may display once again if any ACC activity occurs, which may include any of the following: This feature will only activate when the following conditions are met: The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS", "gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: Once SSC is enabled it will activate automatically once the following conditions are met: The following conditions must be met in order for HSA to activate:", "Diesel Fuel Specifications This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  Note: If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials)", "2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized", "generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and", "Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The", "ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Use good quality diesel fuel from a reputable supplier in your vehicle.  For most year-round service, Number 2 diesel fuel meeting ASTM (formerly known as the American Society for Testing and Materials) specification D-975 Grade S15 will provide good performance.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better", "fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  This diesel engine has been developed to take advantage of the high energy content and generally lower cost Number 2 Ultra Low Sulfur diesel fuel or Number 2 Ultra Low Sulfur climatized diesel fuels.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD", "of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  If you accidentally fill the fuel tank with gasoline or DEF on your diesel vehicle, do not start the engine.  Damage to the engine and fuel system could occur.  Please call an authorized dealer for service.  A maximum blend of 5% biodiesel meeting ASTM specification D-975 may be used with your diesel engine without any adjustments to regular service schedules.  Commercially available fuel additives are not necessary for the proper operation of your diesel engine.  Number 1 Ultra Low Sulfur diesel fuel should only be used where extended arctic conditions (-10\u00b0F or -23\u00b0C) exist.  Use of Climatized ULSD Fuel or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is", "or Number 1 ULSD fuel results in a noticeable decrease in fuel economy.  Climatized ULSD fuel is a blend of Number 2 ULSD fuel and Number 1 ULSD fuel which reduces the temperature at which wax crystals form in fuel.  The fuel grade should be clearly marked on the pump at the fuel station.  Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend using Mopar\u00ae Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of the manufacturer Material Standard MS.90032.  Engine Oil \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae API Certified SAE 5W-40 Full Synthetic Engine Oil which meets the requirements of the manufacturer Material Standard MS-12991.  Equivalent full synthetic SAE 5W-40 engine oil can be used but must be compliant to API SN/SP and ACEA A3/B4 specifications Fuel Filters \u2014 3.0L Diesel Engine We recommend using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the", "using Mopar\u00ae Fuel Filter.  Must meet 3 micron rating.  Using a fuel filter that does not meet the manufacturer filtration and water separating requirements can severely impact fuel system life and reliability.  Fuel Selection \u2014 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle.  Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.  For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance.  We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine.  Diesel Exhaust Fluid \u2014 3.0L Diesel Engine Mopar\u00ae Diesel Exhaust Fluid (DEF)(API Certified) or equivalent that has been API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result", "API Certified to the ISO 22241 standard.  Use of fluids not API Certified to ISO 22241 may result in system damage.  Open the fuel filler door.  Fuel Filler Door Remove the diesel fuel filler cap by rotating it counterclockwise.  Fuel and Diesel Exhaust Fluid (DEF) Fill Location Fully insert the diesel nozzle into the filler pipe.  Fill the vehicle with fuel.  When the nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove the diesel nozzle, reinstall fuel cap and close the fuel filler door.", "Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death", "be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated", "de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  The battery in your vehicle is located in the right rear of the engine compartment.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front", "vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  The Power Distribution Center is located in the engine compartment near the battery.  This center contains cartridge fuses, mini fuses, and relays.  The PDC top cover is labeled with each serviceable fuse/relay location, function, and size.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead", "to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with", "compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.", "If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is", "center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator,", "After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough", "not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a", "changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.", "When To Use 4L Range When off-road driving, shift into 4L for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low speed pulling power.  This range should be limited to extreme situations such as deep snow, mud, steep inclines, or sand where additional low speed pulling power is needed.  Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4L range.  CAUTION: Do not use 4L range when operating the vehicle on dry pavement.  Driveline hardware damage can result.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street", "in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument", "to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the", "provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the", "4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.", "JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in", "pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water", "If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are", "is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-)", "battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a", "If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift", "two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the", "compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure", "Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.  Note: Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle while making connections.", "Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately \"\u21e8air bag warning light\" .  The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning", "as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bags to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Placing an object on", "you drive, have an authorized dealer service the air bag system immediately.  Placing an object on the floor under the front passenger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision.  Do not place any objects on the floor under the front passenger seat.  If there is a fault present in the OCS, both the PAD Indicator Light and the Air Bag Warning Light will illuminate to show that the Passenger Advanced Front Air Bag is deactivated.  Should this occur, the Passenger Advanced Front Air Bag will remain deactivated until the fault is cleared.  This indicates that you should take the vehicle to an authorized dealer for service immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light", "Bag Warning Light comes on intermittently or remains on while driving.  The air bag warning light will illuminate whenever the ocs is unable to classify the front passenger seat status.  A malfunction in the OCS may affect the operation of the air bag system.  If the air bag warning light does not come on, or stays on after you start the vehicle, or it comes on as you drive, take the vehicle to an authorized dealer for service immediately.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check", "Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Air Bag Warning Light This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on", "stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  Air Bag Warning Light The Occupant Restraint Controller (ORC) monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position.  If the ignition switch is in the OFF position or in the ACC position, the air bag system is not on and the air bags will not inflate.  The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or it becomes disconnected prior to deployment.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light,", "If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is detected that could affect the air bag system.  The diagnostics also record the nature of the malfunction.  While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  Note: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint", "the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled.  In this condition the air bags may not be ready to inflate for your protection.  have an authorized dealer service the air bag system immediately.  WARNING: Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.", "Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling contacts from Phonebooks displayed on the touchscreen.  Setting Favorite Contact phone numbers so they are easily accessible on the Main Phone screen.  Viewing and Calling contacts from Recent Call logs.  Reviewing your recent Incoming SMS Messages.  Pairing up to 10 phones/audio devices for easy access to connect to them quickly.  Your mobile phone\u2019s audio is transmitted through your vehicle\u2019s audio system; the system will automatically mute your radio when using the Uconnect Phone.  For uconnect customer support: us visit uconnectphone.com or call 877-855-8400 canada visit uconnectphone.com or call 800-465-2001 (english) or (french) call 800-387-9983 uconnect phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile", "conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  Note: Your phone must be capable of SMS messaging via Bluetooth\u00ae for messaging features to work properly.  WARNING: ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the Uconnect features and applications in this vehicle.  Only use Uconnect when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Start using Uconnect Voice Recognition with", "in an accident involving serious injury or death.  Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: The following basic Voice Commands can be given at any point while using your Uconnect system.  Uconnect Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  Uconnect Phone is a voice-activated, hands-free, in-vehicle communications system.  It allows you to dial a phone number with your mobile phone.  Uconnect Phone will automatically", "It allows you to dial a phone number with your mobile phone.  Uconnect Phone will automatically connect to the highest priority paired phone and/or Audio Device within range.  If you need to choose a particular phone or audio device follow these steps: uconnect can announce incoming text messages.  Push the vr button or phone button and say: the phone feature is driven through your bluetooth\u00ae \u201chands-free profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected", "to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.  Safe Usage Of The Uconnect System The Uconnect system is a sophisticated electronic device.  Do not let young children use the system.  Permanent hearing loss may occur if you play your music or sound system at loud volumes.  Exercise caution when setting the volume on the system.  Keep drinks, rain and other sources of moisture away from the system.  Besides damage to the system, moisture can cause electric shocks as with any electronic device.  Note: Many features of this system are speed dependent.  For your own safety, it is not possible to use some of the touchscreen features while the vehicle is in motion.  Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling", "is in motion.  Screen Activated Features Dialing via Keypad using touchscreen.  Viewing and Calling contacts from Phonebooks displayed on the touchscreen.  Setting Favorite Contact phone numbers so they are easily accessible on the Main Phone screen.  Viewing and Calling contacts from Recent Call logs.  Reviewing your recent Incoming SMS Messages.  Pairing up to 10 phones/audio devices for easy access to connect to them quickly.  Your mobile phone\u2019s audio is transmitted through your vehicle\u2019s audio system; the system will automatically mute your radio when using the Uconnect Phone.  For uconnect customer support: us visit uconnectphone.com or call 877-855-8400 canada visit uconnectphone.com or call 800-465-2001 (english) or (french) call 800-387-9983 uconnect phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system's microphone for private conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free", "for private conversation.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  Note: Your phone must be capable of SMS messaging via Bluetooth\u00ae for messaging features to work properly.  WARNING: ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the Uconnect features and applications in this vehicle.  Only use Uconnect when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Multiple Devices Connecting To", "do so may result in an accident involving serious injury or death.  Multiple Devices Connecting To The Uconnect System \u2014 If Equipped It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.  Note: Apple CarPlay\u00ae and Android Auto\u2122 can only be launched from the front and center console USB ports.", "Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the", "the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other", "will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.", "4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front wheels.  The four-wheel drive system will be automatically engaged when the vehicle senses a loss of traction.  This range provides additional traction for varying road conditions.  2H Two-Wheel Drive High Range \u2014 This range is for normal street and highway driving on dry, hard surfaced roads.  4H AUTO Four-Wheel Drive Auto High Range \u2014 This range sends power to the front wheels.  The four-wheel drive system will be automatically engaged when the vehicle senses a loss of traction.  This range provides additional traction for varying road conditions.  4H Four-Wheel Drive High Range \u2014 This range maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction for loose, slippery road surfaces only.  Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels", "four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  2H (Two-Wheel Drive High Range) 4H (Four-Wheel Drive High Range) N (Neutral) 4L (Four-Wheel Drive Low Range) In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L", "Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  How To Engage The Automatic Locking Mode Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  This indicator will illuminate when a door is ajar/open and not fully closed.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down", "open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Door Latches Check for proper closing, latching, and locking.", "Full Off \u2014 If Equipped This mode is intended for off-highway or off-road use only and should not be used on any public roadways.  In this mode, TCS and ESC features are turned off.  To enter the \u201cFull Off\u201d mode, push and hold the ESC OFF button for five seconds while the vehicle is stopped with the engine running.  After five seconds, a chime will sound, the ESC OFF Indicator Light will illuminate, and the \u201cESC OFF\u201d message will display in the instrument cluster.  To turn ESC on again, momentarily push the ESC OFF button.  If equipped with Off Road+ and if Off Road+ is active when \"Full Off\" mode is enabled by the driver, ESC will not switch to \"Partial Off\" mode at any speed and will remain in \"Full Off\" mode until Off Road+ is exited or ESC is re-enabled by the driver.  Note: System may switch from ESC \u201cFull Off\u201d to \u201cPartial Off\u201d mode when vehicle exceeds a predetermined speed.  When the vehicle speed slows below the predetermined speed the system will return to ESC \u201cFull Off\u201d.  WARNING: In the ESC \u201cFull", "below the predetermined speed the system will return to ESC \u201cFull Off\u201d.  WARNING: In the ESC \u201cFull Off\u201d mode, the engine torque reduction and stability features are disabled.  Therefore, enhanced vehicle stability offered by the ESC system is unavailable.  In an emergency evasive maneuver, the ESC system will not engage to assist in maintaining stability.  ESC \u201cFull Off\u201d mode is intended for off-highway or off-road use only.  The Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  ESC cannot prevent all accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  ESC also cannot prevent collisions.  ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light The ESC Activation/Malfunction Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN mode.  It should go out with", "cluster will come on when the ignition is placed in the ON/RUN mode.  It should go out with the engine running.  If the ESC Activation/Malfunction Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC Activation/Malfunction Indicator Light starts to flash as soon as the tires lose traction and the ESC system becomes active.  The ESC Activation/Malfunction Indicator Light also flashes when the Traction Control System (TCS) is active.  If the ESC Activation/Malfunction Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.  Be sure to adapt your speed and driving to the prevailing road conditions.  The ESC OFF Indicator Light", "to adapt your speed and driving to the prevailing road conditions.  The ESC OFF Indicator Light indicates that the Electronic Stability Control (ESC) is in a reduced mode.  Note: The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  Monitoring battery level status led light red 40% or lower yellow 40% to 70% green 70% to 100% electronic stability control (esc) active warning light \u2014 if equipped this warning light will indicate when the electronic stability control system is active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN", "in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive.  This light will come on when the vehicle is in an ESC event.  Adaptive Cruise Control (ACC) Set Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on", "(ACC) Set Indicator Light \u2014 If Equipped With a Base Instrument Cluster This light will turn on when the vehicle equipped with ACC has been turned on, but not set.", "Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash", "If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped", "and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the", "to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.", "Next, link the Uconnect system on your vehicle to Amazon Alexa: With Amazon Alexa, you can connect to your vehicle and remotely access key services and features.  If your vehicle is equipped with Uconnect Navigation, you can send a destination directly to your vehicle using Alexa.  The Phone feature is driven through your Bluetooth\u00ae \u201cHands-Free Profile\u201d mobile phone.  Uconnect features Bluetooth\u00ae technology \u2014 the global standard that enables different electronic devices to connect to each other without wires or a docking station.  Ensure you phone is turned on with Bluetooth\u00ae active and has been paired to the Uconnect system.  Up to 10 mobile phones or audio devices are allowed to be linked to the system.  Only one linked (or paired) mobile phone and one audio device can be used with the system at a time.  Pair (link) uconnect phone to a mobile phone \u00b9 use this qr code to access your digital experience.  It is possible to have multiple devices connected to the Uconnect system.  For example, if using Android", "possible to have multiple devices connected to the Uconnect system.  For example, if using Android Auto\u2122/Apple CarPlay\u00ae, the connected device will be used to place hands-free phone calls or send hands-free text messages.  However, another device can also be paired to the Uconnect system, via Bluetooth\u00ae, as an audio source, so the passenger can stream music.  Uconnect Phone will automatically connect to the highest priority paired phone and/or Audio Device within range.  If you need to choose a particular phone or audio device follow these steps: Press the Media button on the touchscreen to begin.  Change the source to \u201cBluetooth\u00ae\u201d.  Press the Bluetooth\u00ae button on the touchscreen to display the Paired Audio Devices screen.  Press the Add Device button on the touchscreen.  If there is no device currently connected with the system, a pop-up will appear.  Search for available devices on your Bluetooth\u00ae-enabled audio device.  When prompted on the device, confirm the PIN shown on the Uconnect screen.  Uconnect", "audio device.  When prompted on the device, confirm the PIN shown on the Uconnect screen.  Uconnect Phone will display an in-process screen while the system is connecting.  When the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite device.  Selecting \u201cYes\u201d will make this device the highest priority.  This device will take precedence over other paired devices within range.  After connecting to Android Auto\u2122 or Apple CarPlay\u00ae for the first time and undergoing the setup procedure, the smartphone pairs to the Uconnect system via Bluetooth\u00ae without any setup required every time it is within range, if Bluetooth\u00ae is turned on.  Uconnect offers connections via USB, Bluetooth\u00ae, and auxiliary (AUX) ports.  Voice operation is only available for connected USB and AUX devices.  Amazon Alexa Skill \u2014 If Equipped Enjoy the convenience of using your voice to command your vehicle with Amazon Alexa!  With Amazon Alexa, you can connect to your vehicle and", "to command your vehicle with Amazon Alexa!  With Amazon Alexa, you can connect to your vehicle and remotely access key services and features.  If your vehicle is equipped with Uconnect Navigation, you can send a destination directly to your vehicle using Alexa.  If you need assistance, you can always ask alexa for help, or complete a list of commands by saying: \u201calexa, ask <brand name> for help with my car.\u201d here are a few of the many questions you can ask alexa: \u201calexa, ask <vehicle brand> to start my <vehicle name> with your voice code.\u201d \u201calexa, ask <vehicle brand> to lock my <vehicle name> with your voice code.\u201d \u201calexa, ask <vehicle brand> to send 1000 chrysler drive, auburn hills, michigan to my <vehicle name>.\u201d \u201calexa, ask <vehicle brand> what is the fuel level of my <vehicle name>.\u201d an active subscription to siriusxm guardian\u2122 is required.  To use Amazon Alexa, first, register for SiriusXM Guardian\u2122 Next, link the Uconnect system on your vehicle to Amazon Alexa: Download the Amazon Alexa app on your", "link the Uconnect system on your vehicle to Amazon Alexa: Download the Amazon Alexa app on your mobile device (Apple\u00ae or Android\u2122).  Once in the app, tap MENU and go to SKILLS.  Search for <vehicle brand> skill, then tap Enable.  Tap SAVE SETTINGS when prompted.  Link the vehicle brand name to the <vehicle brand> Skill by tapping LINK ACCOUNT.  Log in using your Owner Account credentials.  This will be the same user name and password you used when registering for SiriusXM Guardian\u2122 connected services.  There will be additional settings to confirm on the following screen.  AUTHORIZE the account to return to the <vehicle brand> Skill.  You can now begin using the <vehicle brand> Skill on Alexa!  Amazon Alexa Skill \u2014 If Equipped Enjoy the convenience of using your voice to command your vehicle with Amazon Alexa!  With Amazon Alexa, you can connect to your vehicle and remotely access key services and features.  If your vehicle is equipped with Uconnect Navigation, you can send a destination directly to your", "If your vehicle is equipped with Uconnect Navigation, you can send a destination directly to your vehicle using Alexa.  If you need assistance, you can always ask alexa for help, or complete a list of commands by saying: \u201calexa, ask <brand name> for help with my car.\u201d here are a few of the many questions you can ask alexa: \u201calexa, ask <vehicle brand> to start my <vehicle name> with your voice code.\u201d \u201calexa, ask <vehicle brand> to lock my <vehicle name> with your voice code.\u201d \u201calexa, ask <vehicle brand> to send 1000 chrysler drive, auburn hills, michigan to my <vehicle name>.\u201d \u201calexa, ask <vehicle brand> what is the fuel level of my <vehicle name>.\u201d an active subscription to siriusxm guardian\u2122 is required.  To use Amazon Alexa, first, register for SiriusXM Guardian\u2122 Next, link the Uconnect system on your vehicle to Amazon Alexa: Download the Amazon Alexa app on your mobile device (Apple\u00ae or Android\u2122).  Once in the app, tap MENU and go to SKILLS.  Search for <vehicle brand> skill, then tap Enable.  Tap SAVE", "the app, tap MENU and go to SKILLS.  Search for <vehicle brand> skill, then tap Enable.  Tap SAVE SETTINGS when prompted.  Link the vehicle brand name to the <vehicle brand> Skill by tapping LINK ACCOUNT.  Log in using your Owner Account credentials.  This will be the same user name and password you used when registering for SiriusXM Guardian\u2122 connected services.  There will be additional settings to confirm on the following screen.  AUTHORIZE the account to return to the <vehicle brand> Skill.  You can now begin using the <vehicle brand> Skill on Alexa!  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that", "media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.  Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Radio Voice", "You can check which smartphones are compatible at g.co/androidauto/requirements.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.", "Window Lockout Switch The window lockout switch allows you to disable the window controls on the rear passenger doors.  To disable the window controls, rotate the switch downward.  To enable the window controls, rotate the switch upward.  Child-Protection Door Lock System \u2014 Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove the sealing plug for access, and use a flat-blade screwdriver (or mechanical key) to rotate the dial to the lock or unlock position.  Note: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test", "it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Note: Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  Auto-Down Feature The driver door power window switch and the front passenger door power window", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.", "Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  Cleaning the trailcam the trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD", "the button is released.  If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.", "With the vehicle rolling at 1 to 3 mph (2 to 5 km/h), shift an automatic transmission into NEUTRAL (N), or press the clutch pedal on a manual transmission.  While the vehicle is coasting at 1 to 3 mph (2 to 5 km/h), shift the transfer case lever firmly to the desired position.  Do not pause with the transfer case in N (Neutral).  Once the shift is completed, place the automatic transmission into DRIVE or release the clutch pedal on a manual transmission.  Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  Apply the parking brake, place the gear selector in NEUTRAL, and press the clutch pedal before starting the vehicle.  This vehicle is equipped with a clutch interlocking ignition system.  It will not start unless the clutch pedal is pressed to the floor.  To Turn On The Engine Using The ENGINE START/STOP Button The transmission must be in PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.", "PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage automatically after 10 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP", "Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in", "lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).", "Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with", "vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not", "you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does", "will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could", "slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will", "the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M", "battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.", "In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  Intentional tampering with emissions control systems can result in civil penalties being assessed against you.  Please read and follow these safety precautions.  Failure to do so may result in injury or property damage.", "and follow these safety precautions.  Failure to do so may result in injury or property damage.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer", "be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale", "emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  Your vehicle is required to have an OBD II and a connection port to allow access to information related to the", "is required to have an OBD II and a connection port to allow access to information related to the performance of your emissions controls.  Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the", "battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  For normal service, periodic fluid level checks are not required.  When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected.  If gear oil leakage is suspected, inspect the fluid level.  Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government", "excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Intentional tampering with the emissions control system can result in civil penalties being assessed against you.  If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Intentional tampering with emissions control systems can result in civil penalties being assessed against you.", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too", "gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat,", "the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating,", "off immediately and call for service.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as", "the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this", "light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to", "before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start.  The vehicle should be serviced if the light stays on through several typical driving styles.  In most situations, the vehicle will drive normally and will not require towing.  When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage.  The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.  WARNING: A malfunctioning catalytic converter, as previously referenced, can reach higher temperatures than in normal operating conditions.  This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants", "wood, cardboard, etc.  This could result in death or serious injury to the driver, occupants or others.  CAUTION: Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.  It also could affect fuel economy and driveability.  If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking", "equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the", "contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting", "which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.  Note: Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle while making connections.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source", "personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the", "brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could", "vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.", "Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts", "Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow", "the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down", "nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.", "the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive", "the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose", "If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.", "If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offIf the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and", "steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate", "Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  This warning light will turn on when there's a fault with the EPS system The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an", "displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistanceIf the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d This warning light will turn on when there's a fault", "Please contact an authorized dealer.\u201d This warning light will turn on when there's a fault with the EPS system When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: Your vehicle is equipped with an Electro-Hydraulic Power Steering system that will provide increased vehicle response and ease of maneuverability.  If the Electro-Hydraulic Power Steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.  The \u201cBRAKE!\u201d screen in the instrument cluster display is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously.  Push the SWAY BAR switch to disconnect or connect the sway bar.", "applying the brakes autonomously.  Push the SWAY BAR switch to disconnect or connect the sway bar.  The Sway Bar Indicator Light (located in the instrument cluster) will illuminate when the bar is disconnected.  The Sway Bar Indicator Light will flash during activation transition, or when activation conditions are not met.  The stabilizer/sway bar should remain in on-road mode during normal driving conditions.  The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.  If the \u201cSERVICE STOP/START SYSTEM\u201d message appears in the instrument cluster display, have the system checked by an authorized dealer.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering", "maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns offThe heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  If the \u201cSERVICE POWER STEERING\u201d message and a flashing icon are displayed on the instrument cluster screen, it indicates that the vehicle needs to be taken to an authorized dealer for service.  It is likely the vehicle has lost power steering assistance The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel", "has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause a fire.  Press the heated steering wheel button once to turn the heating element on.  Press", "cause a fire.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  When the SET (+) or the SET (-) button (located on the steering wheel) is pushed, the display will read \u201cACC SET.\u201d The Phone button on your steering wheel is used to get into the Phone Mode and make calls, show recent, incoming or outgoing calls, view phonebook, etc.  When you push the button you will hear a BEEP.  The BEEP is your signal to give a command.", "Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately \"\u21e8air bag warning light\" .  Air Bag Warning Light The Occupant Restraint Controller (ORC) monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position.  If the ignition switch is in the OFF position or in the ACC position, the air bag system is not on and the air bags will not inflate.  The ORC contains a backup power supply system that may", "not on and the air bags will not inflate.  The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or it becomes disconnected prior to deployment.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is detected that could affect the air bag system.  The diagnostics also record the nature of the malfunction.  While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer", "is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  Note: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled.  In this condition the air bags may not be ready to inflate for your protection.  have an authorized dealer service the air bag system immediately.  WARNING: Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive,", "ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.  Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately Air Bag Warning Light This warning light will illuminate to indicate a fault with the air bag, and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with", "when the ignition is placed in the ON/RUN or ACC/ON/RUN position.  This light will illuminate with a single chime when a fault with the air bag has been detected, it will stay on until the fault is cleared.  If the light is not on during startup, stay on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  Air Bag Warning Light The Occupant Restraint Controller (ORC) monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position.  If the ignition switch is in the OFF position or in the ACC position, the air bag system is not on and the air bags will not inflate.  The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or it becomes disconnected prior to deployment.  The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first in the ON/RUN", "four to eight seconds for a self-check when the ignition switch is first in the ON/RUN position.  After the self-check, the Air Bag Warning Light will turn off.  If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously.  A single chime will sound to alert you if the light comes on again after initial startup.  The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is detected that could affect the air bag system.  The diagnostics also record the nature of the malfunction.  While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.  The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first in the ON/RUN position.  The Air Bag Warning Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on", "Light remains on after the four to eight-second interval.  The Air Bag Warning Light comes on intermittently or remains on while driving.  Note: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled.  In this condition the air bags may not be ready to inflate for your protection.  have an authorized dealer service the air bag system immediately.  WARNING: Ignoring the Air Bag Warning Light in your instrument panel could mean you won\u2019t have the air bag system to protect you in a collision.  If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.", "Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  Who is Covered You are covered by Roadside Assistance services if you are a purchaser for use of the vehicle.  Roadside Assistance services last for five years or 60,000 miles on the odometer, whichever occurs first, calculated from the start date of the Basic Limited Warranty, as set forth in your Warranty Information book.  1 1.  Towing services provided through Cross Country Motor Club, Inc.Medford, MA 02155, except in AK,CA, HI, OR, WI, and WY, where services are provided by Cross Country Motor Club of California, Inc., Thousand Oaks, CA 91360.  Who is Covered You are covered by Roadside Assistance", "California, Inc., Thousand Oaks, CA 91360.  Who is Covered You are covered by Roadside Assistance services if you are a purchaser for use of the vehicle.  Roadside Assistance services last for five years or 60,000 miles on the odometer, whichever occurs first, calculated from the start date of the Basic Limited Warranty, as set forth in your Warranty Information book.  1 1.  Towing services provided through Cross Country Motor Club, Inc. Medford, MA 02155, except in AK,CA, HI, OR, WI, and WY, where services are provided by Cross Country Motor Club of California, Inc., Thousand Oaks, CA 91360.", "If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.", "tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for", "Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  SOS Call \u2014 If Equipped WARNING: Some SiriusXM Guardian\u2122 connected services, including SOS Call and Roadside Assistance Call, will NOT work without a network connection compatible with your device.", "Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.", "the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the", "rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.", "Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a", "electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of", "and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the", "the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.", "Automatic Transmission \u2014 If Equipped  Automatic Transmission \u2014 If Equipped Select the DRIVE range when towing.  The transmission controls include a drive strategy to avoid frequent shifting when towing.  However, if frequent shifting does occur while in DRIVE, you can use the AutoStick shift control to manually select a lower gear.  Note: Using a lower gear while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  This action will also provide better engine braking.  Component Fluid, Lubricant, or Genuine Part Automatic Transmission \u2013 If Equipped Use only Mopar\u00ae ZF 8 & 9 Speed ATF Automatic Transmission Fluid or equivalent.  Failure to use the correct fluid may affect the function or performance of your transmission.  Manual Transmission \u2013 If Equipped We recommend using Mopar\u00ae ATF+4 Automatic Transmission Fluid.  Transfer Case We recommend using Mopar\u00ae ATF+4 Automatic Transmission Fluid.  Front Axle", "Fluid.  Transfer Case We recommend using Mopar\u00ae ATF+4 Automatic Transmission Fluid.  Front Axle Differential We recommend using Mopar\u00ae Gear & Axle Lubricant (SAE 75W85) (API GL-5).  Rear Axle Differential (M220 Sales Codes DRE/DRF) We recommend using Mopar\u00ae Gear & Axle Lubricant (SAE 75W85) (API GL-5).  Models equipped with Trac-Lok Limited Slip Differential require a friction modifier additive.  Brake Master Cylinder We recommend using Mopar\u00ae DOT 3 Brake Fluid, SAE J1703.  Power Steering Reservoir We recommend using Mopar\u00ae Electric Steering Pump Fluid.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.", "to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on us design standards, or \"....blank....\" = passenger car tire based on european design standards, or lt = light truck tire based on us design standards, or t or s = temporary spare tire, or 31 = overall diameter in inches (in) 215, 235, 145 = section width in millimeters (mm) 65, 85, 80 = aspect ratio in percent (%) ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code \"r\" means radial construction, or \"d\" means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index a numerical code associated with the maximum load a tire can carry h = speed", "95 = load index a numerical code associated with the maximum load a tire can carry h = speed symbol a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: xl = extra load (or reinforced) tire, or ll = light load tire or c, d, e, f, g = load range associated with the maximum load a tire can carry at a specified pressure maximum load \u2013 maximum load indicates the maximum load this tire is designed to carry maximum pressure \u2013 maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire if a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have", "for this tire if a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: the gvwr is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire", "in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 What is the phone number for roadside assistance call?  The phone number is: US: 1-800-521-2779 Canada: 1-800-363-4869 If I am subscribed to SiriusXM Guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance?  No, however your new vehicle may include Roadside Assistance Call services.  Setting Name Description Voice Response Length This setting will change the response length for the Voice Recognition system.  The \u201cBrief\u201d setting provides a shortened audio description from the system.  The \u201cDetailed\u201d setting provides the full audio description from the system.  Show Command List This setting will allow you to turn the Command List on or off.  The \u201cAlways\u201d setting will always show the Command List.  The \u201cWith Help\u201d", "Command List on or off.  The \u201cAlways\u201d setting will always show the Command List.  The \u201cWith Help\u201d setting will show the Command List and provide a brief description of what the command does.  The \u201cNever\u201d setting will turn the Command List off.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children.  Every state in the", "vehicle needs to be buckled up at all times, including babies and children.  Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.  This is the law, and you can be prosecuted for ignoring it.  Children 12 years or younger should ride properly buckled up in a rear seat, if available.  According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.  There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.  Always check the child seat Owner\u2019s Manual to make sure you have the correct seat for your child.  Carefully read and follow all the instructions and warnings in the child restraint Owner\u2019s Manual and on all the labels attached to the child restraint.  Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.  You should also make sure", "it has a label certifying that it meets all applicable Safety Standards.  You should also make sure that you can install it in the vehicle where you will use it.  WARNING: In a collision, an unrestrained child can become a projectile inside the vehicle.  The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.  The child and others could be badly injured or killed.  Any child riding in your vehicle should be in a proper restraint for the child\u2019s size.  Note: for additional information, refer to http://www.nhtsa.gov/parents-and-caregivers or call: 1\u2013888\u2013327\u20134236 canadian residents should refer to transport canada\u2019s website for additional information: https://www.tc.gc.ca/en/services/road/child-car-seat-safety.html.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always", "inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children", "in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on", "or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the", "location accessible to children.  A child could operate power windows, other controls, or move the vehicle.", "Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or", "with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of", "and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match", "Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl", "or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the", "driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Engine start-up in very low ambient temperature could result in evident white smoke.", "previously.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the", "This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled.  Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen.  In the following situations, the engine will not stop: driver\u2019s seat belt is not buckled driver\u2019s door is not closed battery temperature is too warm or cold battery charge is low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin", "low the vehicle is on a steep grade cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved hvac is set to full defrost mode at a high blower speed hvac is set to max a/c engine has not reached normal operating temperature engine or exhaust temperature is too high the transmission is not in a forward gear hood is open transfer case is in 4l or n (neutral) brake pedal is not pressed with sufficient pressure accelerator pedal input vehicle speed threshold has not been achieved from previous autostop steering angle is beyond threshold acc is on and speed is set vehicle is at high altitude system fault is present it may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme conditions of the items listed previously.  Conditions that will cause the engine to start automatically while in autostop mode: the transmission selector is moved out of drive to maintain cabin temperature comfort", "mode: the transmission selector is moved out of drive to maintain cabin temperature comfort actual cabin temperature is significantly different than temperature set on auto hvac hvac is set to full defrost mode hvac system temperature or fan speed is manually adjusted battery voltage drops too low stop/start off switch is pushed a stop/start system error occurs stop/start autostop active time exceeds five minutes transfer case is in 4l or n (neutral) steering wheel is turned beyond threshold.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.", "vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle", "that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service", "is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors", "a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software,", "into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.", "will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  Getting High-Centered If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  CAUTION: Winching or rocking the vehicle off hard objects increases the risk of underbody damage.  Jack Location The jack and tools are stored under the right rear seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools", "seat.  See the following steps to remove: Fold up the right rear seat.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat.  Removing the wing bolt release the tool bag straps from the jack and remove tools from bag.  Jack and tool bag remove tool kit and assemble tools.  Jack And Tool Bag There are two ways to assemble the tools: Note: If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  CAUTION: The lug wrench can only be attached to extension 2.  When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism adjusting nut.  Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly WARNING: After using the jack and tools, always reinstall them in the original carrier and location.  While", "After using the jack and tools, always reinstall them in the original carrier and location.  While driving you may experience abrupt stopping, rapid acceleration or sharp turns.  A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.", "UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  Volume & On/Off Control Push the VOLUME & On/Off control knob to turn on", "on the Uconnect system.  Volume & On/Off Control Push the VOLUME & On/Off control knob to turn on and off the Uconnect system.  The electronic volume control turns continuously (360 degrees) in either direction, without stopping.  Turning the VOLUME & On/Off control knob clockwise increases the volume, and counterclockwise decreases it.  When the audio system is turned on, the sound will be set at the same volume level as last played.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to", "setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.", "Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or", "with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of", "and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match", "Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl", "or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.", "4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together,", "the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any", "drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  When To Use 4L Range When off-road driving, shift into 4L for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low speed pulling power.  This range should be limited to extreme situations such as deep snow, mud, steep inclines, or sand where additional low speed pulling power is needed.  Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4L range.  CAUTION: Do not use 4L range when operating the vehicle on dry pavement.  Driveline hardware damage can result.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft,", "\u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive,", "into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.", "BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load", "cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There", "EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed", "cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  Lower Anchors And Tethers For CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the", "belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.", "Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical", "illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.  It may cause burns even at low temperatures, especially if used for long periods of time.  Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion.  This may cause the seat heater to overheat.  Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  The engine must be running for the heated steering wheel to operate.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle", "Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  If the \u201cPOWER STEERING HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme", "HOT\u201d message and an icon are displayed on the instrument cluster screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.  You will lose power steering assistance momentarily until the over temperature condition no longer exists.  Once driving conditions are safe, pull over and let vehicle idle for a few moments until the light turns off  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating", "screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the", "your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  When Remote Start is activated, the front and rear defrost will", "screen of the touchscreen.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The engine must be running for the heated steering wheel to operate.", "SiriusXM Guardian\u2122 In-Vehicle Assistance Features \u2014 If Equipped With SiriusXM Guardian\u2122, your vehicle has onboard assistance features located on the rearview mirror or overhead console designed to enhance your driving experience if you should ever need assistance or support.  SiriusXM Guardian\u2122 In-Vehicle Assistance Features With SiriusXM Guardian\u2122, your vehicle has onboard assistance features located on the rearview mirror or overhead console designed to enhance your driving experience if you should ever need assistance or support.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  Console Storage Compartment The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  INSTRUMENT CLUSTER DISPLAY Your vehicle", "the lower storage compartment, lift the bottom latch.  INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.", "When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle's wheels above 30 mph (48 km/h), or for longer than 30 seconds continuously without stopping.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route", "ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion.  Turn the steering wheel right and left to clear the area around the front wheels.  For vehicles with automatic transmission, push and hold the lock button on the gear selector.  Then, shift back and forth between DRIVE (D) and REVERSE (R) (with automatic transmission) or SECOND (2) gear and REVERSE (R) (with manual transmission), while gently pressing the accelerator.  Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.  Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no", "to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  Mud Deep mud creates a great deal of suction around the tires and is very difficult to get through.  You should use DRIVE, with the transfer case in the 4L position to maintain your momentum.  If you start to slow to a stop, try turning your steering wheel no more than a quarter turn quickly back and forth for additional traction.  Mud holes pose an increased threat of vehicle damage and getting stuck.  They are normally full of debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get", "debris from previous vehicles getting stuck.  As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any", "The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These", "to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it", "for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver.  With the ignition in the OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer.  Your instrument cluster display is designed to display important information about your vehicle\u2019s systems and features.  The driver interactive display, located in the instrument panel, indicates how systems are operating and gives you warnings when a system, or systems, needs your attention.  The steering wheel mounted controls allow you to scroll through and enter the main menus and submenus.  You can access the specific information you want to make selections and adjustments.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen", "display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are", "Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center", "or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature", "to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Opening The Hood Release both of the outside hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood", "hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Note: Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If", "of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.", "Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather.  To clear the windows, select Defrost or Mix mode and increase the front blower speed.  Do not use the Recirculation mode without A/C for long periods, as fogging may occur.  Winter Operation To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used.  Use of the Air Recirculation mode during Winter months is not recommended, because it may cause window fogging.  Do not use abrasive cleaning components, solvents, steel wool, or other aggressive material to clean the lenses.  The lenses in front of the instruments in this vehicle are molded in clear plastic.  When cleaning the lenses, care must be taken to avoid scratching the plastic.  Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.  Do not press the touchscreen with any hard", "different lens cleaning procedures must be followed.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsTo minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.  To remove road dirt, wash with a mild soap solution followed by rinsing.  If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the", "the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  If the \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the windshield and forward-facing camera inspected at an authorized dealer.  All glass surfaces should be cleaned on a regular basis with Mopar\u00ae Glass Cleaner, or any commercial household-type glass cleaner.  Never use an abrasive type cleaner.  Use caution when cleaning the inside rear window equipped with electric defrosters or windows equipped with radio antennas.  Do not use scrapers or other sharp instruments that may scratch the elements.  The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems are experienced.  This inspection should include the following points:", "The engine is allowed to crank as long as 25 seconds.  If the engine fails to start during this period, please wait at least two minutes for the starter to cool before repeating start procedure.  If the Water in Fuel Indicator Light remains on, DO NOT START engine before you drain the water from the fuel filters to avoid engine damageInstall a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible", "pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damageThe system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  Release the parking brake.  The transmission must be in PARK or NEUTRAL.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage", "once.  The system starts the vehicle.  If the vehicle fails to start, the starter will disengage automatically after 10 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Extended Park Starting Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Note: Extended Park condition occurs when the vehicle has not been started or driven for at least 30 days.  CAUTION: To prevent damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15", "damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  If Engine Fails To Start If the engine fails to start after you have followed the \u201cNormal Starting\u201d procedure and the vehicle has not experienced an extended park condition as defined previously, it may be flooded.  Push the accelerator pedal all the way to the floor and hold it there.  Crank the engine for no more than 10 seconds.  This should clear any excess fuel in case the engine is flooded.  Leave the ignition key in the ON/ RUN position, release the accelerator pedal and repeat the \u201cNormal Starting\u201d procedure.  WARNING: Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the", "equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly CAUTION: To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.", "Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  All cargo transported in the pickup box must be secured.  The maximum payload for the mid position is 300 lb (136 kg).  (1) Locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.\u201d on your vehicle's placard.  Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing", "or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.", "Phone & Bluetooth\u00ae Pairing A feature of the Jeep\u00ae wireless speaker is the ability for the Jeep\u00ae wireless speaker to connect to devices using Bluetooth\u00ae.  Follow these simple steps to connect a Bluetooth\u00ae-enabled device to the Jeep\u00ae wireless speaker: Press and hold the power button for 2-3 seconds to turn the Jeep\u00ae wireless speaker on.  Turn \u201con\u201d Bluetooth\u00ae for the device you desire to be connected to the Jeep\u00ae wireless speaker.  For instructions on how to turn on and off Bluetooth\u00ae settings for the desired device, refer to the device\u2019s user manual.  When powered on, the Jeep\u00ae wireless speaker will automatically enter pairing mode.  To pair a second device, press and hold the Bluetooth\u00ae button for 2-3 seconds, until an audio cue is heard.  Then go to the devices\u2019 Bluetooth\u00ae settings and select \u201cJeep\u00ae Speaker\u201d from the list.  The Jeep\u00ae wireless speaker will remember the last eight devices it has paired with.  Note: If the Jeep\u00ae wireless speaker is left on with an inactive Bluetooth\u00ae connection for 30 minutes,", "If the Jeep\u00ae wireless speaker is left on with an inactive Bluetooth\u00ae connection for 30 minutes, it will automatically turn off.  The Jeep\u00ae wireless speaker can be turned on again by pressing and holding the power button for 2-3 seconds.  Press the settings button on the touchscreen.  Press the paired phones or audio sources button.  Press to select the particular phone or the particular audio device.  A pop-up menu will appear; press \u201cConnect Phone\u201d.  Press the X to exit out of the Settings screen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The MAX A/C button is only", "will allow you to toggle up or down through the available settings.  The MAX A/C button is only available on the touchscreen.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsThe SYNC button is only available on the touchscreen.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first", "or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Press the Phone button.  Press the Dial/Keypad button on the touchscreen.  The Touch-Tone screen will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press \u201cDial/Call\u201d.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  Overview Bluetooth\u00ae Streaming Audio or Bluetooth\u00ae Mode is entered by pairing a Bluetooth\u00ae device, containing music, to the Uconnect system.  Before proceeding, the Bluetooth\u00ae device must be paired to the Uconnect Phone to communicate with the Uconnect system.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under", "To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).", "If there is a set speed in memory push the RES (resume) button and then remove your foot from the accelerator pedal.  The instrument cluster display will display the last set speed.  The MAX A/C button is only available on the touchscreen.  The vr button is used to activate/deactivate your voice recognition system.  1 \u2014 All Button 2 \u2014 Presets Button 3 \u2014 Favorites Button 4 \u2014 Game Zone Button 1 \u2014 Radio Button 5 \u2014 Controls Button 2 \u2014 Media Button 6 \u2014 Phone Button 3 \u2014 Climate Button 7 \u2014 Settings Button 4 \u2014 Apps Button  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are", "1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  AUTO Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting.  The AUTO indicator illuminates when AUTO is on.  This feature automatically controls the interior cabin temperature by adjusting distribution and blower speed.  Air conditioning (A/C) may be active during AUTO operation to improve performance.  AUTO Mode is highly recommended for efficiency.  Toggling this function will cause the system to switch between manual mode and automatic modeWhen Seats & Comfort/Auto-On Comfort Systems button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s comfort", "is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s comfort systems when remote start has been activated or the vehicle has been started.  Note: depending on the vehicle\u2019s options, feature settings may vary.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons", "When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts,", "an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your", "corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Only use the positive battery post on the main battery to jump start", "see an authorized dealer.  Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large", "when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  The positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.", "Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  What to Do If your vehicle requires jump start assistance, out of gas/fuel delivery, tire service, lockout service or towing as a result of a mechanical breakdown, dial toll-free: USA: 1-800-521-2779/Canada: 1-800-363-4869.  Provide your name, Vehicle Identification Number (VIN) required for covered services, license plate number, and your location, including the telephone number from which you are calling.  Briefly describe the nature of the problem and answer a few simple questions.  You will be given the name of the service provider and an estimated time of arrival.  If you feel you are in an unsafe", "name of the service provider and an estimated time of arrival.  If you feel you are in an unsafe situation, please let us know.  With your consent, we will contact local police or safety authorities.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10", "to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in", "battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.", "Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that", "media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app", "If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.", "Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 android", "smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in", "your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on", "calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.", "buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once", "and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect", "data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.  Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you", "data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 And Apple CarPlay\u00ae Automatic Bluetooth\u00ae Pairing After connecting to Android Auto\u2122 or Apple CarPlay\u00ae for the first time and undergoing the setup procedure, the smartphone pairs to the Uconnect system via Bluetooth\u00ae without any setup required every time it is within range, if Bluetooth\u00ae is turned on.  Note: Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.", "The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring Height (H) Attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the", "approximately H1 (H2=H1).  The truck can now be driven.  Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer.  You must consider this as part of the load on your vehicle.  Service Forward Collision Warning (FCW) Light \u2014 If Equipped This warning light will illuminate to indicate a fault in the Forward Collision Warning System.", "This warning light will illuminate to indicate a fault in the Forward Collision Warning System.  Contact an authorized dealer for service Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.", "Recommended Distribution Hitch Adjustment Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring height (h) attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing", "for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  Recommended Distribution Hitch Adjustment Position the truck to be ready to connect to the trailer (do not connect the trailer).", "Adjustment Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring height (h) attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Recommended Distribution Hitch Adjustment An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.", "Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.", "Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.  The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window", "switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  Power Window Switches Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.  Window Lockout Switch The window lockout switch allows you to disable the window controls on the rear passenger doors.  To disable the window controls, rotate the switch", "the window controls on the rear passenger doors.  To disable the window controls, rotate the switch downward.  To enable the window controls, rotate the switch upward.", "PARKING BRAKE Before exiting the vehicle, make sure that the parking brake is fully applied.  Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or FIRST gear.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic", "to move the gear selector out of PARK.  Note: When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  WARNING: Never use the PARK position on an automatic transmission as a substitute for the parking brake.  Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.  When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake", "be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.  Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury.  Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear.  Failure to do so may cause the vehicle to roll and cause damage or injury.  CAUTION: If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as", "lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  Always secure your vehicle by fully applying the parking", "brake and make sure the ignition is OFF.  Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a", "your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle", "Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Trailer And Tongue Weight Never exceed the maximum tongue weight stamped on your bumper or trailer hitch.  Consider the following items when computing the weight on the rear axle of the vehicle: the tongue weight of the trailer the weight of any other type of cargo or equipment put in or on your vehicle the weight of the driver and all passengers note: remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is", "weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a", "If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.", "Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be", "Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire dealer or original", "those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result", "what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw", "accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the", "take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Preparations For Jacking Park on a firm, level surface.  Avoid ice or slippery areas.  Warning: do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  Turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers", "if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Note: Passengers should not remain in the vehicle when the vehicle is being jacked in position.", "Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water Flowing water can be extremely dangerous.  Never attempt to cross a fast running stream or river even in shallow water.  Fast moving water can easily push your vehicle downstream, sweeping it out of control.  Even in very shallow water, a high current can still wash the dirt out from around your tires putting you and your vehicle in jeopardy.  There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the vehicle's running ground clearance.  You should never attempt to cross flowing water which is deeper than the vehicle's running ground clearance.  Even the slowest current can push the heaviest vehicle downstream and out of control if the water is deep enough to push on the large surface area of the vehicle's body.  Before you proceed, determine the speed of the current, the water's depth, approach angle, bottom condition and if there are any obstacles.  Then cross at an angle heading", "approach angle, bottom condition and if there are any obstacles.  Then cross at an angle heading slightly upstream using the low and slow technique.  WARNING: Never drive through fast moving deep water.  It can push your vehicle downstream, sweeping it out of control.  This could put you and your passengers at risk of injury or drowning.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible", "and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around", "along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water Flowing water can be extremely dangerous.  Never attempt to cross a fast running stream or river even in shallow water.  Fast moving water can easily push your vehicle downstream, sweeping it out of control.  Even in very shallow water, a high current can still wash the dirt out from around your tires putting you and your vehicle in jeopardy.  There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the vehicle's running ground clearance.  You should never attempt to cross flowing water which is deeper than the vehicle's running ground clearance.  Even the slowest current can push the heaviest vehicle downstream and out of control if the water is deep enough to push on the large", "the heaviest vehicle downstream and out of control if the water is deep enough to push on the large surface area of the vehicle's body.  Before you proceed, determine the speed of the current, the water's depth, approach angle, bottom condition and if there are any obstacles.  Then cross at an angle heading slightly upstream using the low and slow technique.  WARNING: Never drive through fast moving deep water.  It can push your vehicle downstream, sweeping it out of control.  This could put you and your passengers at risk of injury or drowning.  Extreme care should be taken crossing any type of water.  Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner.  You should only drive through areas which are designated and approved.  You should tread lightly and avoid damage to the environment.  You should know your vehicle's abilities and be able to recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep", "recover it if something goes wrong.  You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake.  If the engine stalls, do not attempt to restart it.  Determine if it has ingested water first.  The key to any crossing is low and slow.  Shift into FIRST gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L position and proceed very slowly with a constant slow speed (3 to 5 mph {5 to 8 km/h} maximum) and light throttle.  Keep the vehicle moving; do not try to accelerate through the crossing.  After crossing any water higher than the bottom of the axle differentials, you should inspect all of the vehicle fluids for signs of water ingestion.  Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water.  Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less", "permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or muddy.  When driving through water, do not exceed 5 mph (8 km/h).  Always check water depth before entering as a precaution, and check all fluids afterward.  Driving through water may cause damage that may not be covered by the New Vehicle Limited Warranty.  As you approach any type of water, you need to determine if you can cross it safely and responsibly.  If necessary, get out and walk through the water or probe it with a stick.  You need to be sure of its depth, approach angle, current and bottom condition.  Be careful of murky or muddy waters; check for hidden obstacles.  Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary.  The key to a safe crossing is the water depth, current and bottom conditions.  On soft bottoms, the vehicle will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when", "will sink in, effectively increasing the water level on the vehicle.  Be sure to consider this when determining the depth and the ability to safely cross.  Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.  These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.  Murky or muddy water holes are where you want to hook up tow straps prior to entering.  This makes for a faster, cleaner and easier vehicle recovery.  If you are able to determine you can safely cross, than proceed using the low and slow method.", "Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently", "ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  VEHICLE MODIFICATIONS/ALTERATIONS WARNING: Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in", "methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred", "Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the", "fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).", "While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  Do not use in hilly terrain or with heavy loads.  When using the Cruise Control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.  Use Cruise Control in flat terrain and with light loads to maximize fuel efficiency.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d  While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.  Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate", "speed.  Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  To Accelerate For Passing While the Cruise Control is set, press the accelerator to pass as you would normally.  When the pedal is released, the vehicle will return to the set speed.", "4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  This transfer case is designed to be driven in the two-wheel drive position (2H) or four-wheel drive position (4H AUTO) for normal street and highway conditions on dry hard surfaced roads.  For variable driving conditions, the 4H AUTO mode can be used.  In this mode, the front axle is engaged, but the vehicle's power is sent to the rear wheels.  Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.  Because the front axle is engaged, this mode will result in lower fuel economy than the 2H mode.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together,", "the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any", "drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  4L Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  The transfer case is intended to be driven in the 2H position for normal street and highway conditions, such as hard-surfaced roads.  In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H", "rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L The instrument cluster alerts the driver that the vehicle is in four-wheel drive, and the front and rear driveshafts are locked together.  The light will illuminate when the transfer case is shifted into the 4H position.  When operating your vehicle in 4L, the engine speed will be approximately three times (four times for Rubicon models) that of the 2H or 4H positions at a given road speed.  Take care not to overspeed the engine.  Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.", "each wheel.  Any difference will adversely affect shifting and cause damage to the transfer case.  Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds.  Do not go faster than road conditions permit.  Four-Wheel Drive Low Range \u2014 This range provides low speed four-wheel drive.  It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.  This range provides additional traction and maximum pulling power for loose, slippery road surfaces only.  Do not exceed 25 mph (40 km/h).  2H (Two-Wheel Drive High Range) 4H (Four-Wheel Drive High Range) N (Neutral) 4L (Four-Wheel Drive Low Range) In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.  The 4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal", "4H and 4L positions are intended for loose, slippery road surfaces only and not intended for normal driving.  Driving in the 4H and 4L positions on hard-surfaced roads will cause increased tire wear and damage to the driveline components.  For further information on shifting into 4H or 4L", "Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d", "and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.", "of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear", "Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as", "bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and", "up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up", "the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear", "can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.", "Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the", "start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation", "in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd", "and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start", "10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M", "during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.", "Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard Top Panel(s) Storage Bag \u2014", "that are used when the hard top is not installed on the vehicle.  Hard Top Panel(s) Storage Bag \u2014 If Equipped The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Lay the bag for the panels down so the loops and hooks are facing upward.  Unzip the bag and fold back the outer flap.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Note: ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step four store the freedom top panels bag in a safe location.  Note: Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top", "the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Hard top front panel(s) removal hard top front panel(s) removal \u00b9 use this qr code to access your digital experience.  Fold down the sun visor against the windshield.  Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.  Step two 1 \u2014 outside panel lock 2 \u2014 rear panel lock 3 \u2014 front panel lock unlatch the left side header panel latch located at the top of the windshield.  Step three 1 \u2014 header panel latched 2 \u2014 header panel unlatched remove the left side panel.  Repeat the preceding steps to remove the right side panel.  CAUTION: The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  H Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body, or", "vehicle until the top has been either fully attached to the front header, sport bar, and body, or fully removed.  Failure to follow these cautions may cause interior water damage, stains or mildew: It is recommended that the top be free of water prior to panel removal.  Removing the top, opening a door, or lowering a window while the top is wet may allow water to drip into the vehicle\u2019s interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle\u2019s interior.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle\u2019s interior.  Note: Hard Top Front Panel(s) Installation Set the right side panel on the windshield frame with the locating pin in the front receiver mounting hole, followed by the left side panel, making sure", "the locating pin in the front receiver mounting hole, followed by the left side panel, making sure there is no overhang.  Make sure that the panels are sitting flush with the body.  Secure the panel(s) using the same steps for removal in reverse order.  Note: To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.  The Freedom Top panels storage bag allows you to store your hard top panels.  The storage bag contains two compartments.  Insert the left side hard top panel into the bag with the latches facing upward.  Unfold the black panel divider (ensure the divider is lying flat).  Insert the right side Freedom Top panel into the bag with the latches facing downward.  Ensure the front panel latch is closed prior to inserting the panel into the bag.  Unfold the outer flap and zip the hard top bag closed.  Step Four Store the Freedom Top panels bag in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the", "in a safe location.  Ensure the front panel latch is closed prior to inserting the panel into the panels bag.  There is a pouch located on the front of the bag to store the provided hard top edge protectors that are used when the hard top is not installed on the vehicle.  Start by removing the rear window first.  Use the two straps located on the bottom of each side of the rear window to remove the right and left vertical retainers, as well as the lower center retainer.  Step One (Right Side Shown) Step One While keeping the rear window level, slide it outward in either direction until it is completely separate from its retainer.  Do not pull downward while removing the rear window.  Damage to the retainer could result.  Store the rear window in the soft top rear window storage bag (if equipped), or in a safe location Step Two After removing the rear window, remove the quarter panel cover assemblies starting with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric", "with either side.  Disengage the quarter panel cover assembly from the bottom by pulling the fabric at the bottom upward.  With two hands, grab the front of the quarter panel cover assembly and pull outward to disengage it from its retainer on the door frame.  Step Four Pull the quarter panel cover assembly up and out from the bottom, then pull it down and away from the vehicle to remove.  Step Five Repeat this procedure for the other quarter panel cover assembly.  Store the assemblies in the soft top rear window storage bag (if equipped), or a safe location.", "The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  Based on engine operation conditions, the oil change", "possible, within the next 500 miles (805 km).  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  The engine oil filter should be replaced with a new filter at every engine oil change.  A new engine may consume some oil during its first few thousand miles (kilometers) of operation.  This should be considered a normal part of the break-in and not interpreted as a problem.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator", "has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that", "display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.", "Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the", "form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background", "for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold", "cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by", "the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Get started the", "have incoming text messages read out loud, and place and receive hands-free calls.  Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.", "For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  See Engine Fluids and Lubricants for the correct engine oil viscositySynthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Lubricant should be approximately 1/8 inch (3 mm) below the bottom edge of the oil fill hole.  Use only the manufacturer\u2019s recommended fluid Trac-Lok is especially helpful during slippery driving conditions.  With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction.  Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure", "may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure build-up or your tire pressure will be too low.  1 \u2014 Coolant Temperature 2 \u2014 Oil Temperature 3 \u2014 Battery Voltage 4 \u2014 Transmission Temperature 5 \u2014 Oil Pressure Operation in ambient temperature below 32\u00b0F (0\u00b0C) may require special considerations.  The following charts suggest these options:  Use only the manufacturer\u2019s recommended fluid For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Selection Of Lubricant Use only the manufacturer\u2019s recommended fluid Selection Of Lubricant It is important to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only", "to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only manufacturer's specified transmission fluid It is important to maintain the transmission fluid at the correct level using the recommended fluid.  Note: No chemical flushes should be used in any transmission; only the approved lubricant should be used.  CAUTION: Using a transmission fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder Selection Of Lubricant Use only manufacturer's recommended manual transmission fluid", "Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather.  To clear the windows, select Defrost or Mix mode and increase the front blower speed.  Do not use the Recirculation mode without A/C for long periods, as fogging may occur.  Do not use abrasive cleaning components, solvents, steel wool, or other aggressive material to clean the lenses.  The lenses in front of the instruments in this vehicle are molded in clear plastic.  When cleaning the lenses, care must be taken to avoid scratching the plastic.  Plastic is not as scratch", "cleaning the lenses, care must be taken to avoid scratching the plastic.  Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsTo minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.  To remove road dirt, wash with a mild soap solution followed by rinsing.  If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not", "builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  If the \u201cACC/FCW Limited Functionality Clean Front Windshield\u201d message occurs frequently (e.g.  more than once on every trip) without any snow, rain, mud, or other obstruction, have the windshield and forward-facing camera inspected at an authorized dealer.  All glass surfaces should be cleaned on a regular basis with Mopar\u00ae Glass Cleaner, or any commercial household-type glass cleaner.  Never use an abrasive type cleaner.  Use caution when cleaning the inside rear window equipped with electric defrosters or windows equipped with radio antennas.  Do not use scrapers or other sharp instruments that may scratch the elements.  The wiper blades and wiper arms should be inspected periodically, not just when wiper performance", "The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems are experienced.  This inspection should include the following points:", "For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  See Engine Fluids and Lubricants for the correct engine oil viscositySynthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Lubricant should be approximately 1/8 inch (3 mm) below the bottom edge of the oil fill hole.  Use only the manufacturer\u2019s recommended fluid Trac-Lok is especially helpful during slippery driving conditions.  With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction.  Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure", "may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure build-up or your tire pressure will be too low.  1 \u2014 Coolant Temperature 2 \u2014 Oil Temperature 3 \u2014 Battery Voltage 4 \u2014 Transmission Temperature 5 \u2014 Oil Pressure Operation in ambient temperature below 32\u00b0F (0\u00b0C) may require special considerations.  The following charts suggest these options:  Use only the manufacturer\u2019s recommended fluid For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Synthetic Engine Oils Your engine was designed for synthetic engine oils, only use synthetic API approved engine oils.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE", "oils.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Engine Oil Usage See Engine Fluids and Lubricants for the correct engine oil viscosityOil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in", "operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.", "Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and", "should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers", "steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.", "Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road", "lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5", "fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a", "Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front", "on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water", "door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Door Frame Installation Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten fasteners target torque specification for torx fasteners maximum minimum 44.2 in-lb (5 n\u00b7m) 53.1 in-lb (6 n\u00b7m) 35.4 in-lb (4 n\u00b7m) caution: do not overtighten torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top", "strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step five step five insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.", "Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note:", "reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow", "is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.", "VEHICLE IDENTIFICATION NUMBER (VIN) The VIN is found on the left front corner of the A-pillar, visible from outside of the vehicle through the windshield.  Note: It is illegal to remove or alter the VIN plate.  Vehicle Identification Number Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.  Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle", "driver's side door or pillar.  This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.", "Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the", "windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the", "EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button", "drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the", "Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may", "transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be", "the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeHow long does it take to remotely start my vehicle?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle", "or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will remote start your vehicle more quickly.  However its range is limited.  For example, when you are leaving the stadium after the game, you can use the Vehicle Branded App to remote start your vehicle and have the inside of your vehicle comfortable by the time you get to it.  Will my vehicle be safe if I lose my wireless device?  People sometimes lose their wireless devices, which is why security measures have been engineered into the Vehicle Branded App.  Asking for your username, password and SiriusXM Guardian\u2122 Security PIN help to ensure that nobody can start your vehicle if they happen to find your device.  Can someone drive off with my vehicle using the App?  nob Driving your vehicle still requires the keys to be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the interior before you arrive.  Can I stop a vehicle that is being driven", "to warm up or cool down the interior before you arrive.  Can I stop a vehicle that is being driven with the cancel Remote Vehicle Start command?  nob If the vehicle is in motion, the cancel Remote Vehicle Start button will not stop the vehicle.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "To engage REVERSE gear from the NEUTRAL position, lift the REVERSE ring, located below the knob and move the gear selector all the way left and then forward.  If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward), it is probably in the AutoStick (+/-) position (beside the DRIVE position).  In AutoStick mode, the transmission gear (1, 2, 3, etc.)  is displayed in the instrument cluster.  Move the gear selector to the right (into the DRIVE [D] position) for access to PARK, REVERSE, and NEUTRAL.  To shift the gears, fully press the clutch pedal and place the gear selector into the desired gear position (the diagram for the engagement of the gears is displayed on the handle of the selector).  The gear position will be displayed in the instrument cluster.  Operation To activate AutoStick mode, move the gear selector into the MANUAL (M) position (beside the DRIVE position).  The current transmission gear will be displayed in the instrument cluster.  In AutoStick mode,", "The current transmission gear will be displayed in the instrument cluster.  In AutoStick mode, you can use the gear selector (in the MANUAL position) to manually shift the transmission.  Tapping the gear selector forward (-) while in the MANUAL (M) position will downshift the transmission to the next lower gear.  Tapping the selector rearward (+) will command an upshift.  In AutoStick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result.  It will remain in the selected gear until another upshift or downshift is chosen, except as follows: The transmission will automatically downshift as the vehicle slows (to prevent engine lugging) and will display the current gear.  The transmission will automatically downshift to FIRST gear when coming to a stop.  After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or", "as the vehicle is accelerated.  You can start out, from a stop, in FIRST or SECOND gear (or THIRD gear, in 4L range).  Tapping (+) (at a stop) will allow starting in SECOND gear.  Starting out in SECOND or THIRD gear can be helpful in snowy or icy conditions.  If a requested downshift would cause the engine to overspeed, that shift will not occur.  The system will ignore attempts to upshift at too low of a vehicle speed.  Holding the gear selector in the (-) position will downshift the transmission to the lowest gear possible at the current speed.  Transmission shifting will be more noticeable when AutoStick is enabled.  The system may revert to automatic shift mode if a fault or overheat condition is detected.  To disengage AutoStick mode, return the gear selector to the DRIVE position.  You can shift in or out of the AutoStick position at any time without taking your foot off the accelerator pedal.  Note: When Hill Descent Control is enabled, AutoStick is not active.  WARNING: Do not downshift for", "Note: When Hill Descent Control is enabled, AutoStick is not active.  WARNING: Do not downshift for additional engine braking on a slippery surface.  The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury.  PARK (P) This range supplements the parking brake by locking the transmission.  The engine can be started in this range.  Never attempt to use PARK while the vehicle is in motion.  Apply the parking brake when exiting the vehicle in this range.  When parking on a hill, apply the parking brake before shifting the transmission to PARK.  As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  When exiting the vehicle, always: apply the parking brake shift the transmission into park turn the ignition off remove the key fob from the vehicle the following indicators should be used to ensure that you have properly engaged the transmission into the park position: when shifting into park, push", "you have properly engaged the transmission into the park position: when shifting into park, push the lock button on the gear selector and firmly move the gear selector all the way forward until it stops and is fully seated.  Look at the transmission gear position display and verify that it indicates the PARK position (P), and is not blinking.  With the brake pedal released, verify that the gear selector will not move out of PARK.  Note: On four-wheel drive vehicles, be sure that the transfer case is in a drive position.  WARNING: Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle", "is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the", "the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  CAUTION: Before moving", "A child could operate power windows, other controls, or move the vehicle.  CAUTION: Before moving the transmission gear selector out of PARK, you must start the engine, and also press the brake pedal.  Otherwise, damage to the gear selector could result.  DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain.", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to", "will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  Hazard Warning Flashers Button The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  With extended use the Hazard Warning Flashers may wear down your battery.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Park on a firm, level surface.  Avoid ice or slippery areas.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the", "or changing the wheel.  turn on the Hazard Warning Flashers.  Apply the parking brake.  Shift the automatic transmission into PARK (P), or a manual transmission into REVERSE.  Cycle the ignition to OFF.  Block both the front and rear of the wheel diagonally opposite of the jacking position.  For example, if the driver\u2019s front wheel is being changed, block the passenger\u2019s rear wheel.  Warning CAUTION!  NOTE: TIP: PAGE REFERENCE ARROW FOOTNOTE Cut off fuel to the engine (if equipped) Cut off battery power to the electric motor (if equipped) Flash hazard lights as long as the battery has power Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response System Unlock the power door locks 1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel", "HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal", "contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.", "Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to", "Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Depending on the vehicle\u2019s options, feature settings may vary.  Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Depending on the vehicle\u2019s options, feature settings may vary.  When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Note: depending on the vehicle\u2019s options, feature settings may vary.  Adjustable Chime Volume Settings The Front and Rear chime volume settings are programmable.  The settings may be programmed through the Uconnect system The chime volume", "are programmable.  The settings may be programmed through the Uconnect system The chime volume settings include low, medium, and high.  The factory default volume setting is medium.  ParkSense will retain its last known configuration state through ignition cycles.  When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Note: depending on the vehicle\u2019s options, feature settings may vary.", "Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal", "km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed", "is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  Manual Activation Of The Rear View Camera  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is", "Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the", "on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You", "for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be", "the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE,", "the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying", "this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced", "a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that", "Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.", "TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles", "a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension", "may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled", "using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension", "may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged,", "must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be", "Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.", "Sos call system limitations vehicles sold in mexico do not have sos call system capabilities.  SOS or other emergency line operators in Mexico may not answer or respond to SOS system calls.  If the SOS Call system detects a malfunction, any of the following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d an in-vehicle audio message will state \u201cvehicle device requires service.  Please contact an authorized dealer.\u201d even if the sos call system is fully functional, factors beyond fca us llc\u2019s control may prevent or stop the sos call system operation.  These include, but are not limited to, the following factors: the ignition is in the off position the vehicle\u2019s electrical systems are not intact the sos call system software and/or hardware are damaged", "electrical systems are not intact the sos call system software and/or hardware are damaged during a crash the vehicle battery loses power or becomes disconnected during a vehicle crash lte (voice/data) or 4g (data) network and/or global positioning satellite signals are unavailable or obstructed equipment malfunction at the sos operator facility operator error by the sos operator lte (voice/data) or 4g (data) network congestion weather buildings, structures, geographic terrain, or tunnels warning: ignoring the rearview mirror light could mean you will not have sos call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  WARNING: ALWAYS obey traffic laws and", "service the Occupant Restraint Control system immediately.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber.  Never place anything on or near the vehicle\u2019s LTE (voice/data) or 4G (data) and GPS antennas.  You could prevent LTE (voice/data) or 4G (data) and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable LTE (voice/data) or 4G (data) network connection and a GPS signal is required for the SOS Call system to function properly.  Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to", "not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.  SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important", "the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine", "SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception,", "operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be", "part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.", "STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  STARTING THE ENGINE \u2014 GASOLINE ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside", "ENGINE (IF EQUIPPED) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts.  WARNING: When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all", "preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls,", "Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a", "brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear", "fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.", "Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This", "does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the", "and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Synthetic Engine Oils Your engine was designed for synthetic engine oils, only use synthetic API approved engine oils.  Synthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.", "CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.  Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system.  If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.  Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position.  The light should turn off.  If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.  If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or", "vehicle may require towing.  The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check.  If the light does not come on during starting, have the system checked by an authorized dealer.  Note: This light may turn on if the accelerator and brake pedals are pressed at the same time.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  HAZARD WARNING FLASHERS The Hazard Warning Flashers button is located on the instrument panel below the climate controls.  Push the button to turn on the Hazard Warning Flashers.  When the button is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.  Push the button a second time to turn off the Hazard Warning Flashers.  This is an emergency warning system and it should not be used when the vehicle is", "Flashers.  This is an emergency warning system and it should not be used when the vehicle is in motion.  Use only when your vehicle is disabled or creating a safety hazard warning for other motorists.  When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition is placed in the OFF position.  Note: With extended use the Hazard Warning Flashers may wear down your battery.", "The ignition switch must be in the ACC or ON/RUN position to adjust the power mirrors.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the", "unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP", "is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note:", "to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel", "parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the", "to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer", "doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).", "Event Data Recorder (EDR) This vehicle is equipped with an event data recorder (EDR).  The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle\u2019s systems performed.  The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.  The edr in this vehicle is designed to record such data as: how various systems in your vehicle were operating; whether or not the driver and passenger safety belts were buckled/fastened; how far (if at all) the driver was pressing the accelerator and/or brake pedal; and, how fast the vehicle was traveling.  These data can help provide a better understanding of the circumstances in which crashes and injuries occur.  To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed.  In addition to the vehicle manufacturer,", "required, and access to the vehicle or the EDR is needed.  In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.  Note: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are recorded.  However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.  This vehicle is equipped with an event data recorder (EDR).  The main purpose of an EDR is to record data that will assist in understanding how a vehicle\u2019s systems performed under certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacleThis vehicle is equipped with an event data recorder (EDR).  The main purpose of an EDR", "obstacleThis vehicle is equipped with an event data recorder (EDR).  The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle\u2019s systems performed.  The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.  The EDR in this vehicle is designed to record such data as: To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed.  In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.  EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are recorded.", "conditions and no personal data (e.g., name, gender, age, and crash location) are recorded.  However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.  See the \u201cautomatic locking mode\u201d description \"\u21e8switchable automatic locking retractor (alr)\" for additional information on alr.  EVENT DATA RECORDER (EDR) This vehicle is equipped with an event data recorder (EDR).  The main purpose of an edr is to record data that will assist in understanding how a vehicle\u2019s systems performed under certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle \"\u21e8event data recorder (edr)\" .", "Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the", "windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the", "EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system,", "or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start", "shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all", "Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engineThis allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying", "this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced", "a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that", "Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.", "TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your", "And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau", "the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.", "If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  When parking on a hill, apply the parking brake before shifting the transmission to PARK.  As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel", "Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks", "on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel", "Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If", "if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.", "may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent", "than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  Winter Operation To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used.  Use of the Air Recirculation mode during Winter months is not recommended, because it may cause window fogging.", "Non-Locking Storage Wall The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  There is also an option to remove the wall by removing the four bolts that connect the storage wall to the floor.  Non-Locking Storage Wall The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  There is also an option to remove the wall by removing the four bolts that connect the storage wall to the floor.  Rear Wall Storage Bin To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  Note: The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  The Locking Storage Bin has two keyed locks on the front of", "to limit access to items behind seat.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.", "Using Cruise Control On Hills The transmission may downshift on hills to maintain the vehicle set speed.  The Cruise Control system maintains speed up and down hills.  A slight speed change on moderate hills is normal.  On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Cruise Control.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce,", "the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to", "stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks,", "Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.", "See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of", "Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)", "Towing Requirements To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended: WARNING: Improper towing can lead to a collision.  Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel.  When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.  You could lose control of your vehicle and have a collision.  When hauling cargo, or towing a trailer, do not overload your vehicle or trailer.  Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.  Safety chains must always be used between your vehicle and trailer.  Always connect the chains to the frame or hook retainers of the vehicle hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.", "hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be parked on a grade.  When parking, apply the parking brake on the tow vehicle.  Put the tow vehicle transmission in PARK.  Always block or \"chock\" the trailer wheels.  GCWR must not be exceeded.  Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: gvwr gtw gawr tongue weight rating for the trailer hitch utilized caution: do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven.  The engine, axle or other parts could be damaged.  Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.  This helps the engine and other parts of the vehicle wear in at the heavier loads.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If", "towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose,", "prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.", "towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  This indicator will illuminate when the hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety", "slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  This indicator will illuminate when the hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant", "hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully", "to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Release both of the outside hood latches.", "Lowering the soft top \u00b9 use this qr code to access your digital experience.  Use this QR code to access your digital experience.  Apple carplay\u00ae \u00b9 use this qr code to access your digital experience.  Raising the soft top \u00b9 use this qr code to access your digital experience.  Gasoline instrument clusters gasoline instrument clusters \u00b9 use this qr code to access your digital experience.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail", "Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking", "engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch", "and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center", "Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  High/Low Beam Switch The High/Low Beam switch is", "illuminated cupholders, and front door handles).  High/Low Beam Switch The High/Low Beam switch is located within the multifunction lever on the left side of the steering wheel.  High beam headlights can be used for improved visibility in low lit areas when there is no oncoming traffic.  Otherwise, it is recommended to use the low beam headlights to reduce glare to other vehicles.  With the headlight switch activated, push the multifunction lever toward the instrument panel to switch the headlights to high beams.  The lever will return to the centered position.  To return the headlights to low beam, pull the lever toward the steering wheel, or push the lever toward the instrument panel.", "Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road", "metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint", "done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on", "operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.", "is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.", "FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor", "than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  Do Not Operate The Engine With Failed Parts All engine failures give some warning before the parts fail.  Be on the alert for changes in performance, sounds, and visual evidence that the engine requires service.  Some important clues are: engine misfiring or vibrating severely sudden loss of power unusual engine noises fuel, oil or coolant leaks sudden change, outside the normal operating range, in the engine operating temperature excessive smoke oil pressure drop shifting fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is", "when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment", "avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is", "cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.", "Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to", "of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances", "(if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle", "repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Connected Services Remote Horn & Lights FAQs How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can", "long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "For information on the Door Off Mirror Kit (if equipped) when the front doors are removed, see If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Door Off Mirror To install the Door Off Mirrors, proceed as follows:  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  Door Off Mirror Kit \u2014 If Equipped If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front", "Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  To install the Door Off Mirrors, proceed as follows: Remove both front doorsRemove the cowl bolt closest to the door opening using a #40 Torx head driver, and store in a safe location.  Cowl bolt location push the mirror bracket forward onto the a-pillar, making sure to align the bottom of the bracket with the upper door hinge, and the hole from the removed cowl bolt.  Push bracket onto a-pillar place the bracket bushing behind the mirror bracket (over the cowl bolt hole), then insert the bracket bolt into the mirror bracket, through the bracket bushing.  Attaching mirror bracket to the vehicle 1 \u2014 bracket bushing 2 \u2014 bracket bolt insert the hinge shoulder bolt through the bottom of the upper door hinge up into the mirror bracket, then rotate the bracket knob toward the rear of the vehicle to secure the mirror bracket to the a-pillar.  Attaching mirror bracket to the vehicle 1 \u2014 bracket", "to secure the mirror bracket to the a-pillar.  Attaching mirror bracket to the vehicle 1 \u2014 bracket knob 2 \u2014 hinge shoulder bolt tighten both the bracket bolt and the hinge shoulder bolt with a #40 torx head driver.  Recommended torque specification for the bracket bolt is 6 ft-lb (8 N\u00b7m), and 7.5 ft-lb (10 N\u00b7m) for the hinge shoulder bolt.  Lower the mirror assembly onto the mirror bracket.  Lower mirror assembly onto bracket insert the three mirror screws into the mirror assembly, and tighten into the mirror bracket using a #30 torx head driver.  Recommended torque specification for the mirror screws is 4 ft-lb (5.5 N\u00b7m).  Mirror screw locations repeat the steps on the other side of the vehicle.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For off-road driving tips, see Do not store detached doors inside of the vehicle, as they may fly around and cause personal injury or death in the event of a sudden stop, rough terrain, or a collision.  Note: If this kit is", "injury or death in the event of a sudden stop, rough terrain, or a collision.  Note: If this kit is being installed with the optional lamp bracket, the bracket bushing from step 4 is not needed.  Use the spacer from the lamp bracket.", "For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government", "ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction", "traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.  Temperature Grades The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the", "Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.  Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.  Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C.These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.", "Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  OFF ROAD+ will not function in Two-Wheel Drive High (2H) mode.  If the button is pushed while in 2H mode, the cluster display will show the message \u201cOFF ROAD+ Unavailable Shift to 4WD\u201d.  The ASSIST button is used to automatically connect you to any one of the following support centers: Once the 4G Wi-Fi Hotspot is purchased, you can change its name and the password by selecting the Wi-Fi Hotspot App and pressing the Setup Wi-Fi Hotspot button.  You can also view the connected devices from the app screen by pressing the View Connected Devices button.  If equipped, the ASSIST Button is used for contacting", "pressing the View Connected Devices button.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  1 \u2014 Assist Button 2 \u2014 SOS Button The driver should NEVER use the 4G Wi-Fi Hotspot while driving the vehicle as doing so may result in an accident involving serious injury or death.  ASSIST AND SOS SYSTEM \u2014 IF EQUIPPED If equipped, the overhead console contains an ASSIST and an SOS button.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the", "ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  ASSIST AND SOS SYSTEM \u2014 IF EQUIPPED If equipped, the overhead console contains an ASSIST and an SOS button.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering", "traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  Off Road+ Display \u2014 If Equipped When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will", "messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: 2h: off road+ unavailable, shift to 4wd 4h: 4wd high off road+ active 4l: 4wd low off road+ active adaptive cruise control (acc) and cruise control are not available when using off road+.  If either option is selected, a dedicated message will display indicating that the features are not usable concurrently.  Messages are as follows: 4h: cruise control \u2014 cruise control unavailable in off road+ 4h: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in off road+ 4l: cruise control \u2014 cruise control unavailable in 4wd low 4l: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in 4wd low note: the behavior of electronic stability control while in off road+ varies depending on the 4wd status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also,", "4wd status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also, holding the ESC OFF button for five seconds will turn off ESC.  In 4WD Low, Electronic Stability Control automatically shuts off regardless of the Off Road Status.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too", "gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Potential signs of vehicle overheating: Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to", "be obtained immediately.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement", "to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.", "Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  Bumper end caps are removable on steel bumpers only.  The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 Bolt #2 Remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Before completing the following steps: if your vehicle", "Repeat this procedure on the other side.  Before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step Two 1 \u2014 Hex Bolt Cover Installed 2 \u2014 Hex Bolt Cover Removed Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting", "trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step Six Secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Do Not Overtighten!  Damage to the windshield could result.  Open the fuel filler door.  Fuel Filler Door Remove the fuel cap by rotating it counterclockwise.  Fuel Filler Cap Fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  Lowering the windshield before", "gasoline nozzle, reinstall fuel cap and close the fuel filler door.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx", "the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to", "(two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the", "the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.", "Erasing All The HomeLink\u00ae Channels To erase the channels, follow this procedure: Place the ignition switch into the ON/RUN position.  Push and hold the two outside HomeLink\u00ae buttons (I and III) for up to 20 seconds, or until the HomeLink\u00ae indicator light flashes.  Note: Erasing all channels should only be performed when programming HomeLink\u00ae for the first time.  Do not erase channels when programming additional buttons.  Erasing all channels should only be performed when programming HomeLink\u00ae for the first time.  Do not erase channels when programming additional buttons.  It is recommended that you erase all the channels of your HomeLink\u00ae before you use it for the first time.  All HomeLink\u00ae buttons are programmed using this procedure.  You do not need to erase all channels when programming additional buttons.  To reprogram a single HomeLink\u00ae button that has been previously trained, without erasing all the channels, proceed as follows.  Be sure to determine whether the new device you want to program the", "channels, proceed as follows.  Be sure to determine whether the new device you want to program the HomeLink\u00ae button to has a rolling code, or non-rolling code.  The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door opener Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  HomeLink\u00ae replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting, or home security systems.  The HomeLink\u00ae unit is powered by your vehicle\u2019s 12 Volt battery.  The HomeLink\u00ae buttons that are located in the overhead console or sunvisor designate the three different HomeLink\u00ae channels.  To operate HomeLink\u00ae, push and release any of the programmed HomeLink\u00ae buttons.  These buttons will activate the devices they are programmed to with each press of the corresponding HomeLink\u00ae button.  The HomeLink\u00ae indicator light is located above the center", "of the corresponding HomeLink\u00ae button.  The HomeLink\u00ae indicator light is located above the center button.  Place the ignition in the ON/RUN position.  Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program while keeping the HomeLink\u00ae indicator light in view.  Continue to press and hold the HomeLink\u00ae button, while you press and release (cycle) your hand-held transmitter every two seconds until HomeLink\u00ae has successfully accepted the frequency signal.  The indicator light will flash slowly and then rapidly when fully trained.  Watch for the HomeLink\u00ae indicator to change flash rates.  When it changes, it is programmed.  It may take up to 30 seconds or longer in rare cases.  The garage door may open and close while you are programming.  Press and hold the programmed HomeLink\u00ae button and observe the indicator light.  If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink\u00ae button is", "programming is complete and the garage door/device should activate when the HomeLink\u00ae button is pressed.  To program the two remaining HomeLink\u00ae buttons, repeat each step for each remaining button.  DO NOT erase the channels.", "Using your owner\u2019s site your owner\u2019s site website https://www.mopar.com/en-us.html (us residents), or www.mopar.ca (canadian residents) provides you with all the information you need, all in one place.  You can track your service history, find recommended accessories for your vehicle, watch videos about your vehicle's features, and easily access your manuals.  It is also where you can manage your SiriusXM Guardian\u2122 account.  This section will familiarize you with the key elements of the website that will help you get the most of your SiriusXM Guardian\u2122 connected services.  For customers in the United States, press the Sign In/Register button and enter your email address and password.  For customers in Canada, press the My Vehicle button.  Select from \u201cDashboard\u201d, \u201cVehicle Health Report\u201d, and \u201cRecalls\u201d.  The website will then prompt you to log in using your email address and password.  Edit/edit profile: to manage the details of your siriusxm guardian\u2122 account, such as your contact information, password and", "the details of your siriusxm guardian\u2122 account, such as your contact information, password and siriusxm guardian\u2122 pin, click on the edit/edit profile button to access the details of your account.  Connected services status: this statement will indicate your siriusxm guardian\u2122-equipped vehicle.  Remote commands: for vehicles with an active siriusxm guardian\u2122 subscription, press one of these icons and enter your four-digit siriusxm guardian\u2122 security pin to remotely start (if equipped), lock/unlock doors or sound the horn and flash the lights.  Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada) symbols key if you do not read", "books can be ordered through archway at: 1-800-387-1143 (canada) symbols key if you do not read the entire owner\u2019s manual, you may miss important information.  Observe all Cautions and Warnings.  Service Manuals These comprehensive Service Manuals provide a complete working knowledge of the vehicle, system, and/or components and is written in straightforward language with illustrations, diagrams, and charts.  Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada).", "Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the", "the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  The functions described are for when the Jeep\u00ae wireless speaker is undocked from the vehicle.  When plugged into the docking station, the Jeep\u00ae wireless speaker functions as part of the vehicle\u2019s sound system.  The Jeep\u00ae wireless speaker is IP67 waterproof certified with design in mind to withstand rainfall, waterjets, splashing and being submerged in up to 3 ft (1 m) of water for up to 30 minutes.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the", "the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact.  Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.  This feature notifies the user when the placard tire pressure is attained while inflating or deflating the tire.", "Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button,", "volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold", "which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask", "you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d Enjoy the convenience of using your voice to command your vehicle with Amazon Alexa!  Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  On the Remote Commands screen, you have access to several vehicle features that can be controlled remotely from your mobile device.  These features include locking/unlocking, remote starting, and activating the horn and lights of the vehicle.  You can also push the VR button or Phone button on your steering wheel when the system is listening for a command and be returned to the main or previous menu.  Remote Commands lets you send a request to your vehicle in one of three", "the main or previous menu.  Remote Commands lets you send a request to your vehicle in one of three ways:  Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce", "may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will", "to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.", "Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.  Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue", "is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.", "The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  The heated steering wheel button", "activate the comfort systems whenever the vehicle is started.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  The engine must be running for the heated steering wheel to operate.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in", "The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  The engine must be running for the heated seats to operate.  The level of heat selected will stay on until the operator changes it.  Heated Seat/Vented Seats/Heated Wheel Rear Defroster And Heated Mirrors HVAC System 115 Volt AC Power Inverter System Audio and Telematics System  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the", "warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  Setting name", "of any type and material.  This may cause the steering wheel heater to overheat.  Setting name description auto-on driver heated/ventilated seat & heated steering wheel with vehicle start this setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  Remote Start Comfort Systems \u2014 If Equipped When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering", "wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel", "use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.", "To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped)Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security", "Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.", "system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for", "the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF", "Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY", "system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "To order a hard copy of your Service or Diagnostic Procedure manuals, visit: Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  Diagnostic Procedure Manuals Owner's Manuals, Radio Manuals and Warranty Information Books can be ordered through Archway at:  Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  To order a hard copy", "proven diagnostic tests and a complete list of all tools and equipment.  To order a hard copy of your service or diagnostic procedure manuals, visit: www.techauthority.com (us and canada).  Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  Diagnostic Procedure Manuals To order a hard copy of your Service or Diagnostic Procedure manuals, visit:", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob,", "stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.", "button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur,", "than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If", "locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY", "and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including", "or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:", "Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Important Safety Precautions Please", "the seat belt, which could result in serious injury or death.  Important Safety Precautions Please pay close attention to the information in this section.  It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.  Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: Children 12 years old and under should always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint Never allow children to slide the shoulder belt behind them or under their arm.  You should read the instructions provided with your child restraint to make sure that you are using it", "should read the instructions provided with your child restraint to make sure that you are using it properly.  All occupants should always wear their lap and shoulder belts properly.  The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate.  Do not lean against the door or window.  If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.  If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see \"\u21e8if you need assistance\" for customer service contact information.  WARNING: Never place a rear-facing child restraint in front of an air bag.  A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.  Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing", "Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing child restraint in the rear seat.  If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle.  Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will", "the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Folding The Rear Seats To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently To raise the seatback to the proper position, manually lift the seatback until it locks into place.  To return the head restraint to the proper position, manually lift up until it locks into place.  If interference from the cargo area behind the seat prevents the seatback from fully locking, you will have difficulty returning the seats to their proper position.  Note: Each rear seatback can be locked in an upright position using the vehicle key.  Each seatback must be unlocked to release for", "locked in an upright position using the vehicle key.  Each seatback must be unlocked to release for folding.  Note: The vehicle is equipped with stow clips located on the lower trim, next to the rear seats.  Use these clips to hold the seat belt out of the path of the seatback when it is being folded and raised.  Stow clip location you may experience deformation in the seat cushion from the seat belt buckles if the seats are left folded for an extended period of time.  This is normal.  By simply unfolding the seats to the open position, the seat cushion will return to its normal shape over time.  WARNING: Be certain that the seatback is securely locked into position.  Perform a \u201cpush - pull - push\u201d check to confirm the seat is fully locked.  If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers.  A red indicator on the pull strap will be displayed if the seatback is not securely locked.  An improperly latched seat could cause", "will be displayed if the seatback is not securely locked.  An improperly latched seat could cause serious injury.  Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, adjacent to the anchorage symbols on the seatback.  They are just visible when you lean into the rear seat to install the child restraint.  You will easily feel them if you run your finger along the gap between the seatback and seat cushion.", "See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you", "See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "Closing The Hood To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  WARNING: Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning", "it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Opening The Hood Release both of the outside hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Note: Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in", "use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.", "Off-Road Driving Tips  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled", "you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if", "particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or", "and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or", "with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of", "and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match", "Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl", "or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.", "PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Different colored zones indicate the distance to the rear of the vehicle.  The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever", "Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the", "unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear", "distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the", "camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Rear Seat Unoccupied Indicator Light \u2014 If Equipped This light indicates when the rear passenger seats are unoccupied, and will illuminate in the upper right portion of the instrument cluster display, momentarily replacing the configurable corner information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back", "by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are", "to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure", "using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the", "will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "The Remote Door Lock/Unlock feature provides you the ability to lock or unlock the door on your vehicle without the keys and from virtually any distance.  All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Front door removal front door removal \u00b9 use this qr code to access your digital experience.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  To remove the front", "mirror.  Federal law requires outside mirrors on vehicles for on-road use.  To remove the front doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nut from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin located under the rear seat.  Hinge pin nut remove the plastic wiring access door under the instrument panel by sliding the plastic panel along the door frame toward the seats until the tabs are detached.  Wiring access door note: do not force open; this will break the plastic cover.  Pull up on the red locking tab to unlock the wiring harness.  Closed wiring harness 1 \u2014 red locking tab 2 \u2014 wiring harness lever (closed position) push and hold down the black security tab under the wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014 wiring harness lever (open position) 2 \u2014 black security tab with the wiring harness open, pull straight downward", "lever (open position) 2 \u2014 black security tab with the wiring harness open, pull straight downward on the wiring connector to unplug.  Store the wiring connector in the lower door basket.  With the door in the open position, remove the check screw from the door check attachment on the body side (using a #T40 Torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  See note below if the check arm gets pushed into the door while the door is off.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on", "occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Note: When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  Child-Protection Door Lock System \u2014 Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove", "a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove the sealing plug for access, and use a flat-blade screwdriver (or mechanical key) to rotate the dial to the lock or unlock position.  Note: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection", "Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Note: Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.", "TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles", "a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension", "may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged,", "must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicleCAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.", "device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.", "Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal", "km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Different colored zones indicate the distance to the rear of the vehicle.  The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle", "this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.", "Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on GAWRs, vehicle loading, and trailer towing, see Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.", "capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.", "GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  For further information on GAWRs, vehicle loading, and trailer towing, see  The GAWR is the maximum", "For further information on GAWRs, vehicle loading, and trailer towing, see  The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWRThe GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  For further information on", "weight of your vehicle and trailer when weighed in combination.  For further information on GAWRs, vehicle loading, and trailer towing, see Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.", "Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.", "an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest", "to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or", "resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If You Stall Or Begin To Lose Headway If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before", "vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.", "Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the", "the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other", "will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.", "Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command,", "1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Media Voice Commands Uconnect offers connections via USB, Bluetooth\u00ae, and auxiliary (AUX) ports.  Voice operation is only available for connected USB and AUX devices.  Push the vr button located on the steering wheel.  After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artist: \u201c change source to bluetooth\u00ae\u201d \u201c change source to aux\u201d \u201c change source to usb\u201d \u201c play artist beethoven\u201d; \u201c play album greatest hits\u201d; \u201c play song moonlight sonata\u201d; \u201c play genre classical\u201d did you know: press the browse button on the touchscreen to see all of the music on your usb device.  Your Voice Command must match exactly how the artist, album, song, and genre information is displayed.  Operation Voice commands can be used to operate the Uconnect Phone and to navigate its menu", "Operation Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Say compound commands like \u201cCall John Smith mobile\u201d.  Say the individual commands and allow the system to guide you to complete the task.  You will be prompted for a specific command and then guided through the available options.  Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201ccall\u201d and then \u201cjohn smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201ccall john smith mobile.\u201d for each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the", "parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.", "Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo", "values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the gvwr \"\u21e8vehicle loading\" .", "See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied and the", "push the center button, then lower the lever completely.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the", "should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the", "in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.", "Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  How To Engage The Automatic Locking Mode Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  This indicator will illuminate when a door is ajar/open and not fully closed.  Door Latches Check for proper closing, latching, and locking.  When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the", "door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the", "anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).", "Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather.  To clear the windows, select Defrost or Mix mode and increase the front blower speed.  Do not use the Recirculation mode without A/C for long periods, as fogging may occur.  Winter Operation To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used.  Use of the Air Recirculation mode during Winter months is not recommended, because it may cause window fogging.  Half-doors \u2014 if equipped half-doors \u2014 if equipped \u00b9 use this qr code to access your digital experience.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  CAUTION: Do not run half-doors through an automatic car wash.  This may result in scratches and wax", "CAUTION: Do not run half-doors through an automatic car wash.  This may result in scratches and wax buildup on the windows.  Careless handling and storage of the half-doors may damage the seals resulting in water leaks into the interior of the vehicle.  The upper half-doors must be positioned properly to ensure sealing.  Improper installation can cause water leaks into the interior of the vehicle.  Store the zipper pulls of the upper half-door windows at the upper B-pillar area for both front and rear doors to avoid damage to the windows when not in use.  Do not attempt to operate the half-door zipper in temperatures of 41\u00b0F (5\u00b0C) or below.  Damage to the window may occur.", "Tires Examine tires for excessive tread wear and uneven wear patterns.  Check for stones, nails, glass, or other objects lodged in the tread or sidewall.  Inspect the tread for cuts and cracks.  Inspect sidewalls for cuts, cracks, and bulges.  Check the lug nut/bolt torque for tightness.  Check the tires (including spare) for proper cold inflation pressure.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the", "drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the", "If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the", "is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just", "tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the", "You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check", "to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.", "Key Left Vehicle Feature If a valid key fob is no longer detected inside the vehicle while the vehicle\u2019s ignition system is in the ON/RUN or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument cluster display along with an interior chime.  An exterior audible and visual alert will also be activated to warn the driver.  The vehicle\u2019s horn will rapidly chirp three times along with a single flash of the vehicle\u2019s exterior lights.  Note: The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate", "and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the", "devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp", "Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.", "If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer", "recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  When using a fascia/bumper mounted ball on any model, the trailer weight is limited to 3,500 lb (1,588 kg), 30 ft 2 (2.79 m 2 ) frontal area, and 350 lb (159 kg) tongue weight.  The trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie.  the GVWR), and the GVWR should never exceed the weight referenced on the Tire And Loading Information Placard  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition", "offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  Recommended Distribution Hitch Adjustment Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the", "to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring height (h) attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control", "brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.", "Front door removal front door removal \u00b9 use this qr code to access your digital experience.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  To remove the front doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nut from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin located under the rear seat.  Hinge pin nut remove the plastic wiring access door under the instrument panel by sliding the plastic panel along the door frame toward the seats until the tabs are detached.  Wiring access door note: do not force open; this will break the plastic cover.  Pull up on the red locking tab to unlock the wiring harness.  Closed wiring harness 1 \u2014 red locking tab 2 \u2014 wiring harness lever (closed position) push and hold", "Closed wiring harness 1 \u2014 red locking tab 2 \u2014 wiring harness lever (closed position) push and hold down the black security tab under the wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014 wiring harness lever (open position) 2 \u2014 black security tab with the wiring harness open, pull straight downward on the wiring connector to unplug.  Store the wiring connector in the lower door basket.  With the door in the open position, remove the check screw from the door check attachment on the body side (using a #T40 Torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  See note below if the check arm gets pushed into the door while the door is off.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is", "roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Note: When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  Door Frame", "cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per", "and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may", "is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver", "torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can", "(ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both", "well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Lockout Service Whether the keys are locked in your vehicle or frozen locks are keeping you from getting on your way, help is just a phone call away.  This service is limited to providing access to the vehicle\u2019s seating area.  It does not cover the cost of replacement keys.  VEHICLE MAINTENANCE An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions", "Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  WARNING: You can be badly injured working on or around a motor vehicle.  Only do service work for which you have the knowledge and the proper equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will", "system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result", "to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant", "check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed", "check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.", "Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.  Towing Requirements To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended:", "break-in of your new vehicle drivetrain components, the following guidelines are recommended: WARNING: Improper towing can lead to a collision.  Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel.  When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.  You could lose control of your vehicle and have a collision.  When hauling cargo, or towing a trailer, do not overload your vehicle or trailer.  Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.  Safety chains must always be used between your vehicle and trailer.  Always connect the chains to the frame or hook retainers of the vehicle hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be", "trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be parked on a grade.  When parking, apply the parking brake on the tow vehicle.  Put the tow vehicle transmission in PARK.  Always block or \"chock\" the trailer wheels.  GCWR must not be exceeded.  Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: gvwr gtw gawr tongue weight rating for the trailer hitch utilized caution: do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven.  The engine, axle or other parts could be damaged.  Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.  This helps the engine and other parts of the vehicle wear in at the heavier loads.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for", "backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s", "Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.", "The ParkSense Park Assist system provides visual and audible indications of the distance between the rear and/or front fascia/bumper and a detected obstacle when backing up or moving forward (e.g.  during a parking maneuver).  For system limitations and usage precautions, see ParkSense will turn off the Front Park Assist audible alert (chime) after approximately three seconds when an obstacle has been detected, the vehicle is stationary, and the brake pedal is applied.  ParkSense can be active only when the gear selector is in REVERSE or DRIVE.  If ParkSense is enabled at one of these gear selector positions, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above.  A warning will appear in the instrument cluster display indicating the vehicle is above ParkSense operating speed.  The system will become active again if the vehicle speed is decreased to less than approximately 6 mph (9 km/h).  The ParkSense Warning screen is located within the instrument", "than approximately 6 mph (9 km/h).  The ParkSense Warning screen is located within the instrument cluster display It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.  ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles.  Parking curbs might be temporarily detected or not detected at all.  Obstacles located above or below the sensors will not be detected when they are in close proximity.  The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected.  It is recommended that the driver looks over his/her shoulder when using ParkSense.  Setting Name Description Forward Collision Warning Sensitivity This setting will change the distance at which the Forward Collision Warning (FCW) alert sounds.  The \u201cMedium\u201d setting will have the FCW system signal when an object is in view, and the possibility of a collision is", "will have the FCW system signal when an object is in view, and the possibility of a collision is detected.  The \u201cNear\u201d setting will have the FCW system signal when the object is closer to the vehicle.  The \u201cFar\u201d setting will have the FCW system signal when an object is at a far distance from the vehicle.  Forward Collision Warning This setting will turn the Forward Collision Warning system on or off.  The \u201cOff\u201d setting will deactivate the FCW system.  The \u201cWarning Only\u201d setting will provide only an audible chime when a collision is detected.  The \u201cWarning + Active Braking\u201d setting will provide an audible chime and apply some brake pressure when a collision is detected.  ParkSense This setting will change the type of ParkSense alert when a close object is detected and can provide both an audible chime and a visual display when an object is detected.  Front ParkSense Volume This setting adjusts the volume of the Front ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Rear ParkSense", "Front ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Rear ParkSense Volume This setting adjusts the volume of the Rear ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Blind Spot Alert This setting will change the type of alert provided when an object is detected in a vehicle\u2019s blind spot.  The \u201cOff\u201d setting will turn off Blind Spot Alert.  The \u201cLights\u201d setting will activate the Blind Spot Alert lights on the outside mirrors.  The \u201cLights & Chime\u201d setting will activate both the lights on the outside mirrors and an audible chime.  Hill Start Assist This setting will turn the Hill Start Assist system on or off.  ParkView Backup Camera Active Guidelines This setting will turn the ParkView Backup Camera Active Guidelines on or off.  ParkView Backup Camera Delay This setting will add a timed delay to the ParkView Backup Camera when shifting out of REVERSE.  Fixed ParkView Backup Camera Guidelines This setting will turn the Fixed ParkView Backup Camera", "Fixed ParkView Backup Camera Guidelines This setting will turn the Fixed ParkView Backup Camera Guidelines on or off.  Front Camera Gridlines This setting will turn the Front Camera Gridlines on or off.  Tire Fill Assist This setting will turn Tire Fill Assist on or off.  ParkSense Sensors The four ParkSense sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 79 inches (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.  The six ParkSense sensors, located in the front fascia/bumper, monitor the area in front of the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 47 inches (120 cm) from the front fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.", "in the horizontal direction, depending on the location, type and orientation of the obstacle.  ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster displayIt provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.", "Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the", "windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the", "EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present", "will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a", "engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  When Remote Start is active, and the outside ambient temperature is 40\u00b0F (4.5\u00b0C) or below, the system will automatically activate front defrost for 15 minutes or less.  The time is dependent on the ambient temperature.  Once the timer expires, the system will automatically adjust the", "on the ambient temperature.  Once the timer expires, the system will automatically adjust the settings depending on ambient conditions.  See \u201cRemote Start Comfort Systems \u2014 If Equipped\u201d in the next section for detailed operation.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  These features will stay on through the duration of Remote Start, or until the ignition", "button.  These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeHow long does it take to remotely start my vehicle?  Depending on various conditions, it can take three minutes or more for the request to get", "vehicle?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will remote start your vehicle more quickly.  However its range is limited.  For example, when you are leaving the stadium after the game, you can use the Vehicle Branded App to remote start your vehicle and have the inside of your vehicle comfortable by the time you get to it.  Will my vehicle be safe if I lose my wireless device?  People sometimes lose their wireless devices, which is why security measures have been engineered into the Vehicle Branded App.  Asking for your username, password and SiriusXM Guardian\u2122 Security PIN help to ensure that nobody can start your vehicle if they happen to find your device.  Can someone drive off with my vehicle using the App?  nob Driving your vehicle still requires the keys to be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the", "be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the interior before you arrive.  Can I stop a vehicle that is being driven with the cancel Remote Vehicle Start command?  nob If the vehicle is in motion, the cancel Remote Vehicle Start button will not stop the vehicle.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire", "will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.", "while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across", "the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.", "the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This warning light will indicate when", "the heater/air conditioning (hvac) air flow will be reduced.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display If an obstacle is detected in the center front region, the display will show a", "cluster display If an obstacle is detected in the center front region, the display will show a single solid arc in the center front region with no chime.  As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and a fast sound tone will be heard and will change from fast, to continuous.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling", "A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine", "shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull", "with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Instrument cluster descriptions tachometer indicates the engine speed in revolutions per minute (rpm x 1000).  Caution: do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature gauge the temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the", "gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Caution: driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument cluster display the instrument cluster display features a driver", "dealer for service.  Instrument cluster display the instrument cluster display features a driver interactive display.  Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer indicates vehicle speed.", "Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special", "paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.", "on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage", "tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.", "Drag & Drop Menu Bar The Uconnect features and services in the main menu bar are easily customized for your preference.  Simply follow these steps: press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Note: This feature is only available if the vehicle is in PARK.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the", "the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE", "more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also", "of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up", "press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.", "Brake System In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervals WARNING: Riding the brakes can lead to brake failure and possibly a collision.  Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.  You would not have your full braking capacity in an emergency.  In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervalsYour vehicle is equipped with dual hydraulic brake systems.  If either of the two hydraulic systems lose normal capability, the remaining system will still function.  However, there will be some loss of overall braking effectiveness.  You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.  If the driver does not", "to slow or stop, and potential activation of the Brake Warning Light.  If the driver does not take action based upon these progressive warnings, then the system will provide a limited level of active braking to help slow the vehicle and mitigate the potential forward collision.  If the driver reacts to the warnings by braking and the system determines that the driver intends to avoid the collision by braking but has not applied sufficient brake force, the system will compensate and provide additional brake force as required.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must", "the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user's safety or the safety of others.  Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle", "the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The ACC system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.", "The system automatically prevents wheel lock and enhances vehicle control during braking.  BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems.  If either of the two hydraulic systems lose normal capability, the remaining system will still function.  However, there will be some loss of overall braking effectiveness.  You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.  In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function.  However, the effort required to brake the vehicle will be much greater than that required with the power system operating.  Brake System In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervals WARNING: Riding the brakes can lead to brake failure and possibly a collision.  Driving with your foot", "Riding the brakes can lead to brake failure and possibly a collision.  Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.  You would not have your full braking capacity in an emergency.  Brake Assist System (BAS) The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is", "pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  WARNING: The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user's safety or the safety of others.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob,", "stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are", "for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a", "arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.", "of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door opener Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  HomeLink\u00ae replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting, or home security systems.  The HomeLink\u00ae unit is powered by your vehicle\u2019s 12 Volt battery.  The HomeLink\u00ae buttons that are located in the overhead console or sunvisor designate the three different HomeLink\u00ae channels.  To operate HomeLink\u00ae, push and release any of the programmed HomeLink\u00ae buttons.  These buttons will activate the devices", "push and release any of the programmed HomeLink\u00ae buttons.  These buttons will activate the devices they are programmed to with each press of the corresponding HomeLink\u00ae button.  The HomeLink\u00ae indicator light is located above the center button.  Place the ignition in the ON/RUN position.  Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program while keeping the HomeLink\u00ae indicator light in view.  Continue to press and hold the HomeLink\u00ae button, while you press and release (cycle) your hand-held transmitter every two seconds until HomeLink\u00ae has successfully accepted the frequency signal.  The indicator light will flash slowly and then rapidly when fully trained.  Watch for the HomeLink\u00ae indicator to change flash rates.  When it changes, it is programmed.  It may take up to 30 seconds or longer in rare cases.  The garage door may open and close while you are programming.  Press and hold the programmed HomeLink\u00ae button and observe the indicator light.  If the", "Press and hold the programmed HomeLink\u00ae button and observe the indicator light.  If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink\u00ae button is pressed.  To program the two remaining HomeLink\u00ae buttons, repeat each step for each remaining button.  DO NOT erase the channels.", "Water In Fuel Indicator Light \u2014 If Equipped The Water In Fuel Indicator Light will illuminate when there is water detected in the fuel filter.  If this light remains on, DO NOT start the vehicle before you drain the water from the fuel filter to prevent engine damage, and please see an authorized dealer.  CAUTION: The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Water In Fuel Indicator Light \u2014 If Equipped The Water In Fuel Indicator Light will illuminate when there is water detected in the fuel filter.  If this light remains on, DO NOT start the vehicle before you drain the water from the fuel filter to prevent", "remains on, DO NOT start the vehicle before you drain the water from the fuel filter to prevent engine damage, and please see an authorized dealer.  CAUTION: The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Draining Fuel/Water Separator Filter \u2014 Diesel Engine The fuel/water separator housing is located inside the left frame rail in front of the fuel tank.  The best access to this water drain valve is from under the vehicle.  If necessary remove the fuel filter protective cover to access the water drain valve.  If water is detected in the water separator while the engine is running, or while the ignition switch is", "is detected in the water separator while the engine is running, or while the ignition switch is in the ON position, the Water In Fuel Indicator Light will illuminate and an audible chime will be heard.  At this point you should stop the engine and drain the water from the filter housing.  Within 10 minutes of vehicle shutdown, turn the filter drain valve (located on the bottom of the filter housing) counterclockwise to drain fuel/water; allow the accumulated water to drain.  Leave the drain valve open until all water and contaminants have been removed.  When clear fuel is visible, close the drain valve by turning it clockwise.  Upon proper draining of the water from fuel filter assembly, the Water In Fuel Indicator Light will remain illuminated for approximately 10 seconds.  If the water was drained while the engine was running, the Water In Fuel Indicator Light may remain on for approximately three minutes.  If more than two ounces or 60 ml of fuel have been drained, follow the directions for Priming If The", "more than two ounces or 60 ml of fuel have been drained, follow the directions for Priming If The Engine Has Run Out Of Fuel CAUTION: Do not drain the fuel/water separator filter when the engine is running.  Diesel fuel will damage blacktop paving surfaces.  Drain the filter into an appropriate container.  Note: Care should be taken in disposing of used fluids from your vehicle.  Used fluids, indiscriminately discarded, can present a problem to the environment.  Contact an authorized dealer, service station, or government agency for advice on recycling programs and for where used fluids and filters can be properly disposed of in your area.  Yellow indicator lights 4wd indicator light  \u21e84wd indicator light \u2014 if equipped  4wd low indicator light  \u21e84wd low indicator light \u2014 if equipped  4wd part time indicator light  \u21e84wd part time indicator light \u2014 if equipped  axle locker fault indicator light  \u21e8axle locker fault indicator light \u2014 if equipped  rear axle lock indicator light  \u21e8rear axle lock indicator light \u2014", "indicator light \u2014 if equipped  rear axle lock indicator light  \u21e8rear axle lock indicator light \u2014 if equipped  front and rear axle lock indicator light  \u21e8front and rear axle lock indicator light \u2014 if equipped  forward collision warning off indicator light  \u21e8forward collision warning off indicator light \u2014 if equipped  neutral indicator light  \u21e8neutral indicator light \u2014 if equipped  sway bar indicator light  \u21e8sway bar indicator light \u2014 if equipped  off road+ indicator light  \u21e8off road+ indicator light \u2014 if equipped  cargo light on indicator light  \u21e8cargo light on indicator light  wait to start indicator light  \u21e8wait to start indicator light \u2014 if equipped  low diesel exhaust emissions additive adblue\u00ae (urea) indicator light  \u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped  water in fuel indicator light.  The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel", "is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is locatedSee the following steps for refueling: If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "Without The Key Fob Special care must be taken when the vehicle is towed with the ignition in the OFF position.  The only approved method of towing without the key fob is with a flatbed truck.  Proper towing equipment is necessary to prevent damage to the vehicle.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must", "If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing", "manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicleCAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.", "The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  Manual Mirror Adjustment If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The", "the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Ignoring the Rearview Mirror light could mean you will not have SOS Call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  When cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly", "mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on the mirror.  Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors", "dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.", "Oil Life Reset Without pushing the brake pedal, place the ignition in the ON/RUN mode (do not start the engine).  Navigate to \"Oil Life\" submenu in \"Vehicle Info\" in the instrument cluster display.  Push and hold the ok button until the gauge resets to 100%.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after", "temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Secondary Method", "(after performing the scheduled maintenance), refer to the following procedure.  Secondary Method For Oil Change Reset Procedure Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Note: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.  If necessary, repeat this procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures", "conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern", "time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.", "Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.  CRUISE CONTROL SYSTEMS \u2014 IF EQUIPPED Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC)", "Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system: Cruise Control will keep your vehicle at a constant preset speed.  Adaptive Cruise Control (ACC) will adjust the vehicle speed up to the preset speed to maintain a distance with the vehicle ahead.  Note: In vehicles equipped with ACC, if ACC is not enabled, Fixed Speed Cruise Control will not detect vehicles directly ahead of you.  Always be aware of the feature selected.  Only one Cruise Control feature can operate at a time.  For example, if Fixed Speed Cruise Control is enabled, Adaptive Cruise Control will be unavailable, and vice versa.  Cruise Control When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  The Cruise Control buttons are located on the right side of the steering wheel.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you", "cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Using Cruise Control On Hills The transmission may downshift on hills to maintain the vehicle set speed.  The Cruise Control system maintains speed up and down hills.  A slight speed change on moderate hills is normal.  On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Cruise Control.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  CRUISE CONTROL SYSTEMS \u2014 IF EQUIPPED Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system: Cruise", "may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system: Cruise Control will keep your vehicle at a constant preset speed.  Adaptive Cruise Control (ACC) will adjust the vehicle speed up to the preset speed to maintain a distance with the vehicle ahead.  Note: In vehicles equipped with ACC, if ACC is not enabled, Fixed Speed Cruise Control will not detect vehicles directly ahead of you.  Always be aware of the feature selected.  Only one Cruise Control feature can operate at a time.  For example, if Fixed Speed Cruise Control is enabled, Adaptive Cruise Control will be unavailable, and vice versa.", "VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both", "the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the", "If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your", "involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals:", "the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.", "To Arm The System Follow these steps to arm the Vehicle Security system: Make sure the vehicle\u2019s ignition is placed in the OFF position.  Perform one of the following methods to lock the vehicle: push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zonePush the lock button on the key fob.  If any doors are open, close them.  Note: The Vehicle Security system will not arm if you lock the doors using the manual door lock.  Lock press this button to lock your vehicle.  Vehicle start press this button to start your vehicle.  Horn & lights press this button to sound the horn and activate your lights.  Unlock press this button to unlock your vehicle.  Cancel vehicle start press this button to cancel remote start.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the", "power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.", "To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to", "equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the", "engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not", "de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.", "The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be", "rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds,", "your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional", "vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.", "The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  The battery in your vehicle is located in the right rear of the engine compartment.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  The Power Distribution Center is", "the interior, on the passenger side under the instrument panel.  The Power Distribution Center is located in the engine compartment near the battery.  This center contains cartridge fuses, mini fuses, and relays.  The PDC top cover is labeled with each serviceable fuse/relay location, function, and size.  Replacing The Battery In The Key Fob The recommended replacement battery is CR2450.  Remove the back cover of the key fob by inserting a flat-blade screwdriver into the slot on the bottom of the fob.  Apply light pressure until the cover unsnaps being careful not to damage the seal.  Proceed counterclockwise (in the order shown in the following image) to loosen the remaining snaps until the battery cover can be removed.  1-3 \u2013 back cover pry points remove the depleted battery by inserting a small flat-blade screwdriver into the battery removal slot and sliding the battery forward and upward being careful not to damage the electronic board underneath.  Battery replacement install the new battery into the key", "damage the electronic board underneath.  Battery replacement install the new battery into the key fob, making sure the positive (+) side is facing up.  Slide the battery until it is seated securely below the tabs.  Reassemble the back cover making sure it is properly aligned before snapping it back in place.  Note: Customers are recommended to use a battery obtained from Mopar\u00ae.  Aftermarket coin battery dimensions may not meet the original OEM coin battery dimensions.  Perchlorate material \u2014 special handling may apply.  See www.dtsc.ca.gov/hazardouswaste/perchlorate for further information.  Do not touch the battery terminals that are on the back housing or the printed circuit board.  When a key fob battery is low, a warning will be indicated on the vehicle\u2019s instrument cluster, and the fob LED will no longer illuminate with a button push.  WARNING: The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can", "ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or", "and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast", "case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.", "WARNING LIGHTS AND MESSAGES The warning/indicator lights will illuminate in the instrument panel together with a dedicated message and/or acoustic signal when applicable.  These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner\u2019s Manual, which you are advised to read carefully in all cases.  Always refer to the information in this chapter in the event of a failure indication.  All active telltales will display first if applicable.  The system check menu may appear different based upon equipment options and current vehicle status.  Some telltales are optional and may not appear.  ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster displayIt provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.  Screen setup push and release the up or down arrow button until the screen setup menu", "obstacle.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper", "MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.", "To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side", "cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and", "cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.", "Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be", "(load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's", "They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  When using a fascia/bumper mounted ball on any model, the trailer weight is limited to 3,500 lb (1,588 kg), 30 ft 2 (2.79 m 2 ) frontal area, and 350 lb (159 kg) tongue weight.  The trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie.", "tongue weight must be considered as part of the combined weight of occupants and cargo (ie.  the GVWR), and the GVWR should never exceed the weight referenced on the Tire And Loading Information Placard", "If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The", "the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye", "Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  From the Sunrider\u00ae Position, remove straps if", "put the top down or roll the rear or side curtains.  From the Sunrider\u00ae Position, remove straps if previously secured.  Step One Failure to follow the next steps could result in damage to the soft top or vehicle.  Using the side link, lift and push the soft top toward the front of the vehicle, manually guiding the top into the closed position.  Step Two Step Two From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Step Three Pull the handle back upward while squeezing the hook, locking the latch into place.  Step Four It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the", "be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed", "causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may", "may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper", "into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.  Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.  Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror.  The Outside Mirrors are located on the front driver and passenger side doors, and are adjusted manually or by power adjustment (if equipped).  If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  Outside Mirrors The Outside Mirrors are located on the front driver and passenger side doors, and are adjusted manually or by power adjustment (if equipped).  To receive maximum benefit, adjust the Outside", "manually or by power adjustment (if equipped).  To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  For information on the Door Off Mirror Kit (if equipped) when the front doors are removed, see WARNING: Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.  Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.  Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror.  Outside Mirrors The Outside Mirrors are located on the front driver and passenger side doors, and are adjusted manually or by power adjustment (if equipped).  To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  For information on the Door Off", "with a slight overlap of the view obtained on the inside mirror.  For information on the Door Off Mirror Kit (if equipped) when the front doors are removed, see WARNING: Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.  Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.  Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Automatic Dimming Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should", "\u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  This mirror automatically adjusts for headlight glare from vehicles behind you.  The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Note: The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.", "Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The ACC system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  ACC The Adaptive Cruise Control (ACC) on/off button is pushed", "wrong or missing distance warnings.  ACC The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged  Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.  Adaptive Cruise Control (ACC) Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC ACC will allow you to keep Cruise Control engaged in light to moderate traffic conditions without the constant need to reset your speed.  ACC utilizes a radar sensor and a forward-facing camera designed to detect a vehicle directly ahead of you to maintain a set", "and a forward-facing camera designed to detect a vehicle directly ahead of you to maintain a set speed.  Note: If the ACC sensor detects a vehicle ahead, ACC will apply limited braking or accelerate (not to exceed the original set speed) automatically to maintain a preset following distance, while matching the speed of the vehicle ahead.  Any chassis/suspension or tire size modifications to the vehicle will affect the performance of the Adaptive Cruise Control and Forward Collision Warning system.  Fixed Speed Cruise Control (ACC not enabled) will not detect vehicles directly ahead of you.  Always be aware of the feature selected WARNING: Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete", "brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The acc system: does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  You should turn the ACC system off and do not use: When driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.e., in highway construction zones).  When entering a turn lane or highway off-ramp; when driving on roads that are winding, icy, snow-covered, slippery, or have steep uphill or downhill", "driving on roads that are winding, icy, snow-covered, slippery, or have steep uphill or downhill slopes.  When towing a trailer up or down steep slopes.  When circumstances do not allow safe driving at a constant speed.  Precautions While Driving With ACC In certain driving situations, ACC may have detection issues.  In these cases, ACC may brake late or unexpectedly.  The driver needs to stay alert and may need to intervene.  The following are examples of these types of situations: Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.", "STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can", "(ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both", "well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Lockout Service Whether the keys are locked in your vehicle or frozen locks are keeping you from getting on your way, help is just a phone call away.  This service is limited to providing access to the vehicle\u2019s seating area.  It does not cover the cost of replacement keys.  VEHICLE MAINTENANCE An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions", "Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  WARNING: You can be badly injured working on or around a motor vehicle.  Only do service work for which you have the knowledge and the proper equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will", "system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result", "to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive", "have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an", "could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to", "properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.", "Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that", "media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app", "If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.", "Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 android", "smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in", "your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on", "calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon", "Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .", "The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  The battery in your vehicle is located in the right rear of the engine compartment.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  The Power Distribution Center is", "the interior, on the passenger side under the instrument panel.  The Power Distribution Center is located in the engine compartment near the battery.  This center contains cartridge fuses, mini fuses, and relays.  The PDC top cover is labeled with each serviceable fuse/relay location, function, and size.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.", "OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator", "establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster", "could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.", "transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast", "both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full", "operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  In the driver and outboard front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck.  Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Lumbar Support The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control", "Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  Lumbar Support Control Knob Turning the temperature control knob clockwise increases the heating temperature and turning the temperature control knob counterclockwise decreases the heating temperature.", "With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, see These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.  How To Use Remote Start Push and release the Remote Start button on the key fob twice within five seconds.  The vehicle doors and tailgate will lock, the", "button on the key fob twice within five seconds.  The vehicle doors and tailgate will lock, the turn signals will flash twice, and the horn will chirp twice.  Pushing the Remote Start button again will shut the engine off.  All of the following conditions must be met before the engine will remote start: gear selector in park doors closed hood closed hazard switch off brake switch inactive (brake pedal not pressed) battery at an acceptable charge level panic button not pushed fuel meets minimum requirement system not disabled from previous remote start event vehicle security system not active all removable doors must not be removed malfunction indicator/check engine telltale is not illuminated water in fuel telltale is not illuminated wait to start telltale is not illuminated for additional remote start information, see.  Note: With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then", "be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  WARNING LIGHTS AND MESSAGES The warning/indicator lights will illuminate in the instrument panel together with a dedicated message and/or acoustic signal when applicable.  These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner\u2019s Manual, which you are advised to read carefully in all cases.  Always refer to the information in this chapter in the event of a failure indication.  All active telltales will display first if applicable.  The system check menu may appear different based upon equipment", "will display first if applicable.  The system check menu may appear different based upon equipment options and current vehicle status.  Some telltales are optional and may not appear.  How To Use Remote Start Push and release the Remote Start button on the key fob twice within five seconds.  The vehicle doors and tailgate will lock, the turn signals will flash twice, and the horn will chirp twice.  Pushing the Remote Start button again will shut the engine off.  All of the following conditions must be met before the engine will remote start: gear selector in park doors closed hood closed hazard switch off brake switch inactive (brake pedal not pressed) battery at an acceptable charge level panic button not pushed fuel meets minimum requirement system not disabled from previous remote start event vehicle security system not active all removable doors must not be removed malfunction indicator/check engine telltale is not illuminated water in fuel telltale is not illuminated wait to start telltale is not", "telltale is not illuminated water in fuel telltale is not illuminated wait to start telltale is not illuminated for additional remote start information, see.  Note: With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  Driver And Passenger BeltAlert \u2014 If Equipped BeltAlert is a feature intended to remind the driver and outboard front seat passenger (if equipped with outboard front passenger seat BeltAlert) to buckle their seat belts.  The Belt Alert feature is active whenever the ignition switch is in the START or ON/RUN position.", "Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  To order a hard copy of your service or diagnostic procedure manuals, visit: www.techauthority.com (us and canada).  Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  Diagnostic Procedure Manuals To order a hard copy of your Service or Diagnostic Procedure manuals, visit:", "Procedure Manuals To order a hard copy of your Service or Diagnostic Procedure manuals, visit:  To order a hard copy of your Service or Diagnostic Procedure manuals, visit: Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  Diagnostic Procedure Manuals Owner's Manuals, Radio Manuals and Warranty Information Books can be ordered through Archway at:", "Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side.  Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.  Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle.  If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.  Diesel Exhaust Fluid Diesel Exhaust Fluid (DEF) sometimes known simply by the name of its active component, UREA, is a key component of Selective Catalytic Reduction (SCR) systems, which help diesel vehicles meet stringent emission regulations.  DEF is a liquid reducing agent that reacts with engine exhaust in the presence of a catalyst to convert smog-forming Nitrogen Oxides (NOx) into harmless nitrogen and water vapor.  For further information  Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may", "Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side.  Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.  Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle.  If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.  Vehicle Identification Number Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.", "REFUELING IN EMERGENCY \u2013 IF EQUIPPED The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Note: In certain cold conditions, ice may prevent the fuel door from opening.  If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button.  Do not pry on the door.  REFUELING IN EMERGENCY \u2013 IF EQUIPPED The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Note: In certain cold conditions, ice may prevent the", "flappers with the funnel to avoid spills.  Note: In certain cold conditions, ice may prevent the fuel door from opening.  If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button.  Do not pry on the door.  Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an", "in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)", "Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Brake Warning Light This warning light", "ON/RUN mode, have the light repaired as soon as possible.  Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event", "be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If", "light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light", "is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition", "as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS", "level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If", "(ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.", "Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Lowering the windshield before completing the", "windshield is raised prior to installing the tops.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center", "windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  FOLDING WINDSHIELD The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element", "your vehicle on-road with the windshield down, as you lose the protection this structural element provides.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  WARNING: Carefully follow these warnings to help protect against personal injury: Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as", "vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshieldUsing the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to", "(two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Cleaning Instructions During windshield down applications, dust/dirt can accumulate in the cover and block the camera lens.  Use a microfiber cloth to clean the camera lens, module, and inside cover, being careful not to damage or scratch the module.", "The ignition switch must be in the ACC or ON/RUN position to adjust the power mirrors.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the", "unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP", "is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d The buttons on the right side of the steering wheel operate the ACC system.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The", "Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged ACC Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following appears in the instrument cluster display:  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the", "modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire", "system.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the", "completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.", "Event Data Recorder (EDR) This vehicle is equipped with an event data recorder (EDR).  The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle\u2019s systems performed.  The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.  The edr in this vehicle is designed to record such data as: how various systems in your vehicle were operating; whether or not the driver and passenger safety belts were buckled/fastened; how far (if at all) the driver was pressing the accelerator and/or brake pedal; and, how fast the vehicle was traveling.  These data can help provide a better understanding of the circumstances in which crashes and injuries occur.  To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed.  In addition to the vehicle manufacturer,", "required, and access to the vehicle or the EDR is needed.  In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.  Note: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are recorded.  However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.  This vehicle is equipped with an event data recorder (EDR).  The main purpose of an EDR is to record data that will assist in understanding how a vehicle\u2019s systems performed under certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacleThis vehicle is equipped with an event data recorder (EDR).  The main purpose of an EDR", "obstacleThis vehicle is equipped with an event data recorder (EDR).  The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle\u2019s systems performed.  The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.  The EDR in this vehicle is designed to record such data as: To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed.  In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.  EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are recorded.", "conditions and no personal data (e.g., name, gender, age, and crash location) are recorded.  However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.  See the \u201cautomatic locking mode\u201d description \"\u21e8switchable automatic locking retractor (alr)\" for additional information on alr.  EVENT DATA RECORDER (EDR) This vehicle is equipped with an event data recorder (EDR).  The main purpose of an edr is to record data that will assist in understanding how a vehicle\u2019s systems performed under certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle \"\u21e8event data recorder (edr)\" .", "Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the", "windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the", "EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this range WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system,", "or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  To Exit Remote Start Mode To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  Note: To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start", "shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.  For vehicles equipped with the Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry feature, the message \u201cRemote Start Active \u2014 Push Start Button\u201d will display in the instrument cluster display until you push the START/STOP ignition button.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all", "Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engineThis allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely", "with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The front panel(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top assembly must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc.  T Do not move your vehicle until the top has been either fully attached to the windshield frame and body, or fully removed.  The removal of the hard top requires four adults located on each corner.  Failure to follow this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying", "this caution could damage the hard top.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced", "a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that", "Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.", "TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your", "And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau", "the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.", "If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  When parking on a hill, apply the parking brake before shifting the transmission to PARK.  As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel", "Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.  For vehicles equipped with an automatic transmission, apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks", "on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel", "Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If", "if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.", "may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent", "than the one specified for your vehicle.  Personal injury or engine damage may result.  To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.  Winter Operation To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used.  Use of the Air Recirculation mode during Winter months is not recommended, because it may cause window fogging.", "Non-Locking Storage Wall The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  There is also an option to remove the wall by removing the four bolts that connect the storage wall to the floor.  Non-Locking Storage Wall The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.  There is also an option to remove the wall by removing the four bolts that connect the storage wall to the floor.  Rear Wall Storage Bin To access the storage bin, pull upward on the pull strap located on the upper outboard side of the right rear seat, and fold the seatback forward.  Note: The rear seatback can be locked using the vehicle key to secure items in the rear wall storage bin.  The seat lock is located on the upper outboard side of each seatback.  Both seatbacks should be locked to limit access to items behind seat.  The Locking Storage Bin has two keyed locks on the front of", "to limit access to items behind seat.  The Locking Storage Bin has two keyed locks on the front of the bin and uses the same key as the glove compartment and the center console for your vehicle.  The center console has both an upper and lower storage compartment.  To open the upper storage compartment, lift the top latch.  To access the lower storage compartment, lift the bottom latch.  The mechanical flip key can be used to lock or unlock the door cylinders, tailgate, glove compartment, and storage compartments (if equipped).  All doors can be programmed to unlock on the first push of the unlock button through Uconnect SettingsThe mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  The Non-Locking Storage Wall can be used for storage by folding the bottom of the rear seat up and placing items behind the wall.", "Using Cruise Control On Hills The transmission may downshift on hills to maintain the vehicle set speed.  The Cruise Control system maintains speed up and down hills.  A slight speed change on moderate hills is normal.  On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Cruise Control.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce,", "the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to", "stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks,", "Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.", "See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of", "Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)", "Towing Requirements To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended: WARNING: Improper towing can lead to a collision.  Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel.  When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.  You could lose control of your vehicle and have a collision.  When hauling cargo, or towing a trailer, do not overload your vehicle or trailer.  Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.  Safety chains must always be used between your vehicle and trailer.  Always connect the chains to the frame or hook retainers of the vehicle hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.", "hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be parked on a grade.  When parking, apply the parking brake on the tow vehicle.  Put the tow vehicle transmission in PARK.  Always block or \"chock\" the trailer wheels.  GCWR must not be exceeded.  Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: gvwr gtw gawr tongue weight rating for the trailer hitch utilized caution: do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven.  The engine, axle or other parts could be damaged.  Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.  This helps the engine and other parts of the vehicle wear in at the heavier loads.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If", "towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose,", "prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.", "towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.", "Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both", "radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  This indicator will illuminate when the hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety", "slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  This indicator will illuminate when the hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant", "hood is ajar/open and not fully closed.  You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never open a cooling system pressure cap when the radiator or coolant bottle is hot.  Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.  The fan starts automatically and may start at any time, whether the engine is running or not.  When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition to the OFF position.  The fan is temperature controlled and can start at any time the ignition is in the ON position.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully", "to open.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Release both of the outside hood latches.", "Lowering the soft top \u00b9 use this qr code to access your digital experience.  Use this QR code to access your digital experience.  Apple carplay\u00ae \u00b9 use this qr code to access your digital experience.  Raising the soft top \u00b9 use this qr code to access your digital experience.  Gasoline instrument clusters gasoline instrument clusters \u00b9 use this qr code to access your digital experience.  Lowering the soft top \u00b9 use this qr code to access your digital experience.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail", "Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking", "engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Headlight Switch The headlight switch is located on the left side of the instrument panel.  This switch controls the operation of the headlights, parking lights, automatic headlights (if equipped), instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).  Rotate the headlight switch clockwise to the first detent for parking lights and instrument panel light operation.  Rotate the headlight switch to the second detent for headlights, parking lights, and instrument panel light operation.  Note: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch", "and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  Note: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel light position to the first detent to turn on headlights, parking lights, and instrument panel light.  Rotate the headlight switch to the second detent for the AUTO position.  Interior Courtesy Lights The Interior Courtesy Lights will turn on when the front doors are opened, by rotating the instrument panel dimmer control (dial on the right) on the headlight switch fully upward while the doors are closed, or if equipped, when the unlock button is pushed on the key fob.  The Interior Courtesy Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center", "Lights are located in the center of the vehicle\u2019s sport bar, and consist of one large center light and four smaller reading lights.  Each reading light can be turned on by pushing the lens.  Pushing the lens a second time will turn the light off.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  High/Low Beam Switch The High/Low Beam switch is", "illuminated cupholders, and front door handles).  High/Low Beam Switch The High/Low Beam switch is located within the multifunction lever on the left side of the steering wheel.  High beam headlights can be used for improved visibility in low lit areas when there is no oncoming traffic.  Otherwise, it is recommended to use the low beam headlights to reduce glare to other vehicles.  With the headlight switch activated, push the multifunction lever toward the instrument panel to switch the headlights to high beams.  The lever will return to the centered position.  To return the headlights to low beam, pull the lever toward the steering wheel, or push the lever toward the instrument panel.", "Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road", "metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint", "done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on", "operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.", "is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.", "FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  FUEL REQUIREMENTS \u2014 GASOLINE ENGINE While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern.  However, if the engine is heard making a heavy knocking sound, see an authorized dealer immediately.  Use of gasoline with an octane number lower than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor", "than recommended can cause engine failure and may void the New Vehicle Limited Warranty.  Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.  If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.  Do Not Operate The Engine With Failed Parts All engine failures give some warning before the parts fail.  Be on the alert for changes in performance, sounds, and visual evidence that the engine requires service.  Some important clues are: engine misfiring or vibrating severely sudden loss of power unusual engine noises fuel, oil or coolant leaks sudden change, outside the normal operating range, in the engine operating temperature excessive smoke oil pressure drop shifting fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is", "when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment", "avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is", "cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.", "Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to", "of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances", "(if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle", "repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Connected Services Remote Horn & Lights FAQs How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can", "long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "For information on the Door Off Mirror Kit (if equipped) when the front doors are removed, see If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Door Off Mirror To install the Door Off Mirrors, proceed as follows:  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  Door Off Mirror Kit \u2014 If Equipped If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front", "Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  To install the Door Off Mirrors, proceed as follows: Remove both front doorsRemove the cowl bolt closest to the door opening using a #40 Torx head driver, and store in a safe location.  Cowl bolt location push the mirror bracket forward onto the a-pillar, making sure to align the bottom of the bracket with the upper door hinge, and the hole from the removed cowl bolt.  Push bracket onto a-pillar place the bracket bushing behind the mirror bracket (over the cowl bolt hole), then insert the bracket bolt into the mirror bracket, through the bracket bushing.  Attaching mirror bracket to the vehicle 1 \u2014 bracket bushing 2 \u2014 bracket bolt insert the hinge shoulder bolt through the bottom of the upper door hinge up into the mirror bracket, then rotate the bracket knob toward the rear of the vehicle to secure the mirror bracket to the a-pillar.  Attaching mirror bracket to the vehicle 1 \u2014 bracket", "to secure the mirror bracket to the a-pillar.  Attaching mirror bracket to the vehicle 1 \u2014 bracket knob 2 \u2014 hinge shoulder bolt tighten both the bracket bolt and the hinge shoulder bolt with a #40 torx head driver.  Recommended torque specification for the bracket bolt is 6 ft-lb (8 N\u00b7m), and 7.5 ft-lb (10 N\u00b7m) for the hinge shoulder bolt.  Lower the mirror assembly onto the mirror bracket.  Lower mirror assembly onto bracket insert the three mirror screws into the mirror assembly, and tighten into the mirror bracket using a #30 torx head driver.  Recommended torque specification for the mirror screws is 4 ft-lb (5.5 N\u00b7m).  Mirror screw locations repeat the steps on the other side of the vehicle.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For off-road driving tips, see Do not store detached doors inside of the vehicle, as they may fly around and cause personal injury or death in the event of a sudden stop, rough terrain, or a collision.  Note: If this kit is", "injury or death in the event of a sudden stop, rough terrain, or a collision.  Note: If this kit is being installed with the optional lamp bracket, the bracket bushing from step 4 is not needed.  Use the spacer from the lamp bracket.", "For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government", "ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction", "traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.  Temperature Grades The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the", "Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.  Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.  Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C.These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.", "Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  OFF ROAD+ will not function in Two-Wheel Drive High (2H) mode.  If the button is pushed while in 2H mode, the cluster display will show the message \u201cOFF ROAD+ Unavailable Shift to 4WD\u201d.  The ASSIST button is used to automatically connect you to any one of the following support centers: Once the 4G Wi-Fi Hotspot is purchased, you can change its name and the password by selecting the Wi-Fi Hotspot App and pressing the Setup Wi-Fi Hotspot button.  You can also view the connected devices from the app screen by pressing the View Connected Devices button.  If equipped, the ASSIST Button is used for contacting", "pressing the View Connected Devices button.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  1 \u2014 Assist Button 2 \u2014 SOS Button The driver should NEVER use the 4G Wi-Fi Hotspot while driving the vehicle as doing so may result in an accident involving serious injury or death.  ASSIST AND SOS SYSTEM \u2014 IF EQUIPPED If equipped, the overhead console contains an ASSIST and an SOS button.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the", "ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  ASSIST AND SOS SYSTEM \u2014 IF EQUIPPED If equipped, the overhead console contains an ASSIST and an SOS button.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering", "traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  Off Road+ Display \u2014 If Equipped When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will", "messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: 2h: off road+ unavailable, shift to 4wd 4h: 4wd high off road+ active 4l: 4wd low off road+ active adaptive cruise control (acc) and cruise control are not available when using off road+.  If either option is selected, a dedicated message will display indicating that the features are not usable concurrently.  Messages are as follows: 4h: cruise control \u2014 cruise control unavailable in off road+ 4h: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in off road+ 4l: cruise control \u2014 cruise control unavailable in 4wd low 4l: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in 4wd low note: the behavior of electronic stability control while in off road+ varies depending on the 4wd status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also,", "4wd status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also, holding the ESC OFF button for five seconds will turn off ESC.  In 4WD Low, Electronic Stability Control automatically shuts off regardless of the Off Road Status.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons", "IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids", "control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single", "If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too", "gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Potential signs of vehicle overheating: Do not open hot engine cooling system.  Never add engine coolant (antifreeze) when the engine is overheated.  Do not loosen or remove the cap to cool an overheated engine.  Heat causes pressure to build-up in the cooling system.  To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.  Do not use a pressure cap other than the one specified for your vehicle.  Personal injury or engine damage may result.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to", "be obtained immediately.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement", "to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.", "Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.  Bumper end caps are removable on steel bumpers only.  The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 Bolt #2 Remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Before completing the following steps: if your vehicle", "Repeat this procedure on the other side.  Before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step Two 1 \u2014 Hex Bolt Cover Installed 2 \u2014 Hex Bolt Cover Removed Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting", "trim).  Step Five 1 \u2014 Outer Torx Fasteners 2 \u2014 Center Torx Fasteners Store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step Six Secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Do Not Overtighten!  Damage to the windshield could result.  Open the fuel filler door.  Fuel Filler Door Remove the fuel cap by rotating it counterclockwise.  Fuel Filler Cap Fully insert the gasoline nozzle into the filler pipe.  Fill the vehicle with fuel.  When the fuel nozzle \u201cclicks\u201d or shuts off, the fuel tank is full.  Wait five seconds before removing the fuel nozzle to allow excess fuel to drain from nozzle.  Remove gasoline nozzle, reinstall fuel cap and close the fuel filler door.  Lowering the windshield before", "gasoline nozzle, reinstall fuel cap and close the fuel filler door.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx", "the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to", "(two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Bumper End Cap Removal \u2014 If Equipped The end caps on your vehicle\u2019s front bumper can be removed by the following steps: Loosen the two bolts that retain the GAWR bracket (Bolts #1 and #2) to the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the", "the end cap using a T45 Torx bit screwdriver.  Do not remove the bolts.  Bolt #1 bolt #2 remove the remaining eight bolts.  Gently remove the end cap from the vehicle and store it where it will not get damaged.  Repeat this procedure on the other side.  Note: Bumper end caps are removable on steel bumpers only.", "Erasing All The HomeLink\u00ae Channels To erase the channels, follow this procedure: Place the ignition switch into the ON/RUN position.  Push and hold the two outside HomeLink\u00ae buttons (I and III) for up to 20 seconds, or until the HomeLink\u00ae indicator light flashes.  Note: Erasing all channels should only be performed when programming HomeLink\u00ae for the first time.  Do not erase channels when programming additional buttons.  Erasing all channels should only be performed when programming HomeLink\u00ae for the first time.  Do not erase channels when programming additional buttons.  It is recommended that you erase all the channels of your HomeLink\u00ae before you use it for the first time.  All HomeLink\u00ae buttons are programmed using this procedure.  You do not need to erase all channels when programming additional buttons.  To reprogram a single HomeLink\u00ae button that has been previously trained, without erasing all the channels, proceed as follows.  Be sure to determine whether the new device you want to program the", "channels, proceed as follows.  Be sure to determine whether the new device you want to program the HomeLink\u00ae button to has a rolling code, or non-rolling code.  The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door opener Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  HomeLink\u00ae replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting, or home security systems.  The HomeLink\u00ae unit is powered by your vehicle\u2019s 12 Volt battery.  The HomeLink\u00ae buttons that are located in the overhead console or sunvisor designate the three different HomeLink\u00ae channels.  To operate HomeLink\u00ae, push and release any of the programmed HomeLink\u00ae buttons.  These buttons will activate the devices they are programmed to with each press of the corresponding HomeLink\u00ae button.  The HomeLink\u00ae indicator light is located above the center", "of the corresponding HomeLink\u00ae button.  The HomeLink\u00ae indicator light is located above the center button.  Place the ignition in the ON/RUN position.  Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program while keeping the HomeLink\u00ae indicator light in view.  Continue to press and hold the HomeLink\u00ae button, while you press and release (cycle) your hand-held transmitter every two seconds until HomeLink\u00ae has successfully accepted the frequency signal.  The indicator light will flash slowly and then rapidly when fully trained.  Watch for the HomeLink\u00ae indicator to change flash rates.  When it changes, it is programmed.  It may take up to 30 seconds or longer in rare cases.  The garage door may open and close while you are programming.  Press and hold the programmed HomeLink\u00ae button and observe the indicator light.  If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink\u00ae button is", "programming is complete and the garage door/device should activate when the HomeLink\u00ae button is pressed.  To program the two remaining HomeLink\u00ae buttons, repeat each step for each remaining button.  DO NOT erase the channels.", "Using your owner\u2019s site your owner\u2019s site website https://www.mopar.com/en-us.html (us residents), or www.mopar.ca (canadian residents) provides you with all the information you need, all in one place.  You can track your service history, find recommended accessories for your vehicle, watch videos about your vehicle's features, and easily access your manuals.  It is also where you can manage your SiriusXM Guardian\u2122 account.  This section will familiarize you with the key elements of the website that will help you get the most of your SiriusXM Guardian\u2122 connected services.  For customers in the United States, press the Sign In/Register button and enter your email address and password.  For customers in Canada, press the My Vehicle button.  Select from \u201cDashboard\u201d, \u201cVehicle Health Report\u201d, and \u201cRecalls\u201d.  The website will then prompt you to log in using your email address and password.  Edit/edit profile: to manage the details of your siriusxm guardian\u2122 account, such as your contact information, password and", "the details of your siriusxm guardian\u2122 account, such as your contact information, password and siriusxm guardian\u2122 pin, click on the edit/edit profile button to access the details of your account.  Connected services status: this statement will indicate your siriusxm guardian\u2122-equipped vehicle.  Remote commands: for vehicles with an active siriusxm guardian\u2122 subscription, press one of these icons and enter your four-digit siriusxm guardian\u2122 security pin to remotely start (if equipped), lock/unlock doors or sound the horn and flash the lights.  Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada) symbols key if you do not read", "books can be ordered through archway at: 1-800-387-1143 (canada) symbols key if you do not read the entire owner\u2019s manual, you may miss important information.  Observe all Cautions and Warnings.  Service Manuals These comprehensive Service Manuals provide a complete working knowledge of the vehicle, system, and/or components and is written in straightforward language with illustrations, diagrams, and charts.  Owner's Manuals These Owner's Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA vehicles.  To access your owner's information online, visit www.mopar.com/om (us) or www.owners.mopar.ca (canada).  Or call tech authority toll free at: 1-800-890-4038 (us) owner's manuals, radio manuals and warranty information books can be ordered through archway at: 1-800-387-1143 (canada).", "Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the", "the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  The functions described are for when the Jeep\u00ae wireless speaker is undocked from the vehicle.  When plugged into the docking station, the Jeep\u00ae wireless speaker functions as part of the vehicle\u2019s sound system.  The Jeep\u00ae wireless speaker is IP67 waterproof certified with design in mind to withstand rainfall, waterjets, splashing and being submerged in up to 3 ft (1 m) of water for up to 30 minutes.  Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.  Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.  This is a normal occurrence and can be minimized.  If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.  If the", "the rear windows open, open the front and rear windows together to minimize the buffeting.  If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.  Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact.  Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.  This feature notifies the user when the placard tire pressure is attained while inflating or deflating the tire.", "Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button,", "volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold", "which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask", "you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d Enjoy the convenience of using your voice to command your vehicle with Amazon Alexa!  Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  On the Remote Commands screen, you have access to several vehicle features that can be controlled remotely from your mobile device.  These features include locking/unlocking, remote starting, and activating the horn and lights of the vehicle.  You can also push the VR button or Phone button on your steering wheel when the system is listening for a command and be returned to the main or previous menu.  Remote Commands lets you send a request to your vehicle in one of three", "the main or previous menu.  Remote Commands lets you send a request to your vehicle in one of three ways:  Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  With Apple CarPlay\u00ae, push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  You can also press and hold the Home button within Apple CarPlay\u00ae to start talking to Siri.  This allows you to make calls or listen to voicemail as you normally would using Siri on your iPhone\u00ae.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce", "may vary.  The vr button is used to activate/deactivate your voice recognition system.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will", "to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.", "Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.  Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue", "is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.", "The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  The heated steering wheel button", "activate the comfort systems whenever the vehicle is started.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  The engine must be running for the heated steering wheel to operate.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in", "The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  The engine must be running for the heated seats to operate.  The level of heat selected will stay on until the operator changes it.  Heated Seat/Vented Seats/Heated Wheel Rear Defroster And Heated Mirrors HVAC System 115 Volt AC Power Inverter System Audio and Telematics System  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the", "warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  Setting name", "of any type and material.  This may cause the steering wheel heater to overheat.  Setting name description auto-on driver heated/ventilated seat & heated steering wheel with vehicle start this setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  Remote Start Comfort Systems \u2014 If Equipped When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings  Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering", "wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel", "use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.", "To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped)Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security", "Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.", "system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for", "the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF", "Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY", "system is armed, the interior power door lock switches will not unlock the doors.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "To order a hard copy of your Service or Diagnostic Procedure manuals, visit: Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  Diagnostic Procedure Manuals Owner's Manuals, Radio Manuals and Warranty Information Books can be ordered through Archway at:  Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  To order a hard copy", "proven diagnostic tests and a complete list of all tools and equipment.  To order a hard copy of your service or diagnostic procedure manuals, visit: www.techauthority.com (us and canada).  Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  Diagnostic Procedure Manuals To order a hard copy of your Service or Diagnostic Procedure manuals, visit:", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob,", "stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.", "button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur,", "than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If", "locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY", "and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including", "or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:", "Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Important Safety Precautions Please", "the seat belt, which could result in serious injury or death.  Important Safety Precautions Please pay close attention to the information in this section.  It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.  Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: Children 12 years old and under should always ride buckled up in the rear seat of a vehicle with a rear seat.  A child who is not big enough to wear the vehicle seat belt properly must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint Never allow children to slide the shoulder belt behind them or under their arm.  You should read the instructions provided with your child restraint to make sure that you are using it", "should read the instructions provided with your child restraint to make sure that you are using it properly.  All occupants should always wear their lap and shoulder belts properly.  The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate.  Do not lean against the door or window.  If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.  If the air bag system in this vehicle needs to be modified to accommodate a disabled person, see \"\u21e8if you need assistance\" for customer service contact information.  WARNING: Never place a rear-facing child restraint in front of an air bag.  A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.  Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing", "Never install a rear-facing child restraint in the front seat of a vehicle.  Only use a rear-facing child restraint in the rear seat.  If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle.  Rear Seat Armrest \u2014 If Equipped The center part of the rear seat can also be used as a rear armrest with cupholders.  To unfold it, grab the pull strap under the head restraint and pull it forward.  Note: The cupholder liner can be removed for cleaning.  WARNING: Be certain that the seatback is securely locked into position.  If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.  An improperly latched seat could cause serious injury.  Manual Front Seatback Recline Adjustment To recline the seat, pull on the recline strap and lean forward or rearward, depending on the direction you would like the seatback to move.  Release the strap when the desired position is reached and the seatback will", "the seatback to move.  Release the strap when the desired position is reached and the seatback will lock into place.  WARNING: Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.  In a collision you could slide under the seat belt, which could result in serious injury or death.  Folding The Rear Seats To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently To raise the seatback to the proper position, manually lift the seatback until it locks into place.  To return the head restraint to the proper position, manually lift up until it locks into place.  If interference from the cargo area behind the seat prevents the seatback from fully locking, you will have difficulty returning the seats to their proper position.  Note: Each rear seatback can be locked in an upright position using the vehicle key.  Each seatback must be unlocked to release for", "locked in an upright position using the vehicle key.  Each seatback must be unlocked to release for folding.  Note: The vehicle is equipped with stow clips located on the lower trim, next to the rear seats.  Use these clips to hold the seat belt out of the path of the seatback when it is being folded and raised.  Stow clip location you may experience deformation in the seat cushion from the seat belt buckles if the seats are left folded for an extended period of time.  This is normal.  By simply unfolding the seats to the open position, the seat cushion will return to its normal shape over time.  WARNING: Be certain that the seatback is securely locked into position.  Perform a \u201cpush - pull - push\u201d check to confirm the seat is fully locked.  If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers.  A red indicator on the pull strap will be displayed if the seatback is not securely locked.  An improperly latched seat could cause", "will be displayed if the seatback is not securely locked.  An improperly latched seat could cause serious injury.  Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, adjacent to the anchorage symbols on the seatback.  They are just visible when you lean into the rear seat to install the child restraint.  You will easily feel them if you run your finger along the gap between the seatback and seat cushion.", "See the following steps for refueling: The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)  The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you", "See the following steps for refueling: Emergency Gas Can Refueling If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d", "Closing The Hood To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  WARNING: Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  To close the hood, remove the support rod from the radiator crossmember, and install into the clip on the hood.  Lower the hood slowly.  Secure both of the hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Release both of the outside hood latches.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning", "it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.  Opening The Hood Release both of the outside hood latches.  Raise the hood slightly, and place a hand palm-side down in the center of the hood opening.  Locate the safety latch in the middle, and push the latch to the right to open.  Remove the support rod from the hood, and insert it into the radiator crossmember.  Note: Vehicle must be at a stop and the gear selector must be in PARK.  You may have to push down slightly on the hood before pushing the safety latch.  While lifting the hood, use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in", "use both hands.  Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position.", "Off-Road Driving Tips  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled", "you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if", "particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or", "and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Washing \u2013 use mopar\u00ae car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or", "with soft bristles.  If extra cleaning is required, use Mopar\u00ae Convertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath.  Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of", "and to prevent corrosion.  Wash wheels with the same soap solution recommended for the body of the vehicle, and remember to always wash when the surfaces are not hot to the touch.  Special Care If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match", "Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  Washing Wash your vehicle regularly.  Always wash your vehicle in the shade using Mopar\u00ae Car Wash, or a mild car wash soap, and rinse the panels completely with water.  If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar\u00ae Super Kleen Bug and Tar Remover to remove.  Use a high quality cleaner wax, such as Mopar\u00ae Cleaner Wax, to remove road film and stains, and to protect your paint finish.  Use precautions to not scratch the paint.  Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.  CAUTION: Do not use abrasive or strong cleaning materials, such as steel wool or scouring powder, that will scratch metal and painted surfaces.  Use of power washers exceeding 1,200 psi (8,274 kPa) can result in damage or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl", "or removal of paint and decals.  Plastic And Coated Parts Use Mopar\u00ae Total Clean to clean vinyl upholstery.  CAUTION: Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage.  Wipe away immediately.  Damage caused by these type of products may not be covered by your New Vehicle Limited Warranty.", "PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Different colored zones indicate the distance to the rear of the vehicle.  The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever", "Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the", "unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear", "distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the", "camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Rear Seat Unoccupied Indicator Light \u2014 If Equipped This light indicates when the rear passenger seats are unoccupied, and will illuminate in the upper right portion of the instrument cluster display, momentarily replacing the configurable corner information.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back", "by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are", "to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure", "using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button", "Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the", "a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back", "REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA", "rinse with water, and dry with a soft cloth.  Do not cover the lens.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.  Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the", "will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.", "The Remote Door Lock/Unlock feature provides you the ability to lock or unlock the door on your vehicle without the keys and from virtually any distance.  All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Front door removal front door removal \u00b9 use this qr code to access your digital experience.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  To remove the front", "mirror.  Federal law requires outside mirrors on vehicles for on-road use.  To remove the front doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nut from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin located under the rear seat.  Hinge pin nut remove the plastic wiring access door under the instrument panel by sliding the plastic panel along the door frame toward the seats until the tabs are detached.  Wiring access door note: do not force open; this will break the plastic cover.  Pull up on the red locking tab to unlock the wiring harness.  Closed wiring harness 1 \u2014 red locking tab 2 \u2014 wiring harness lever (closed position) push and hold down the black security tab under the wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014 wiring harness lever (open position) 2 \u2014 black security tab with the wiring harness open, pull straight downward", "lever (open position) 2 \u2014 black security tab with the wiring harness open, pull straight downward on the wiring connector to unplug.  Store the wiring connector in the lower door basket.  With the door in the open position, remove the check screw from the door check attachment on the body side (using a #T40 Torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  See note below if the check arm gets pushed into the door while the door is off.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on", "occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Note: When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  Child-Protection Door Lock System \u2014 Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove", "a Child-Protection Door Lock system.  To use the system, open each rear door, temporarily remove the sealing plug for access, and use a flat-blade screwdriver (or mechanical key) to rotate the dial to the lock or unlock position.  Note: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  WARNING: Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection", "Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  Note: Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.", "TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles", "a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension", "may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged,", "must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicleCAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.", "device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.", "Zoom View When the Rear View Camera image is being displayed, and the vehicle speed is below 8 mph (13 km/h) while in any gear, Zoom View is available.  By pressing the \u201cmagnifying glass\u201d icon in the upper left of the display screen, the image will zoom in to four times the standard view.  Pressing the icon a second time will return the view to the standard Back Up Camera display.  When Zoom View is selected while the vehicle is in REVERSE, then shifted to DRIVE, the camera delay view will display the standard Back Up Camera view.  If the vehicle is then returned to REVERSE gear from DRIVE, the Zoom View selection will automatically resume.  Shifting to NEUTRAL from any gear will maintain the selected view (Zoom or Standard) as long as the vehicle is below 8 mph (13 km/h).  If the vehicle is in PARK, Zoom View is available until the gear selector is placed in DRIVE or REVERSE and speeds are at or above 8 mph (13 km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal", "km/h).  Note: If the vehicle is in DRIVE, NEUTRAL, or REVERSE, and speed is greater than or equal to 8 mph (13 km/h), Zoom View is unavailable and the icon will appear gray.  While in Zoom View, the guidelines will not be visible.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Different colored zones indicate the distance to the rear of the vehicle.  The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle", "this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  PARKVIEW REAR BACK UP CAMERA The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Note: Removing the tailgate will disable the rearview camera function.", "Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.  You will not exceed the tire's load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire And Loading Information PlacardTo determine the maximum loading conditions of your vehicle, locate the statement \u201cThe combined weight of occupants and cargo should never exceed XXX kg or XXX lbs\u201d on the Tire And Loading Information Placard.  The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.  Note: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  For further information on GAWRs, vehicle loading, and trailer towing, see Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.", "capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR WARNING: It is important that you do not exceed the maximum front or rear GAWR.  A dangerous driving condition can result if either rating is exceeded.  Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.", "GAWR of each axle is not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.  Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).  Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle's GVWR.  For further information on GAWRs, vehicle loading, and trailer towing, see  The GAWR is the maximum", "For further information on GAWRs, vehicle loading, and trailer towing, see  The GAWR is the maximum permissible load on the front and rear axles.  The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.  The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  The GAWR is the maximum capacity of the front and rear axles.  Distribute the load over the front and rear axles evenly.  Make sure that you do not exceed either front or rear GAWR The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWRThe GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  For further information on", "weight of your vehicle and trailer when weighed in combination.  For further information on GAWRs, vehicle loading, and trailer towing, see Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded.", "Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  Hill climbing requires good judgment and a good understanding of your abilities and your vehicle's limitations.  Hills can cause serious problems.  Some are just too steep to climb and should not be attempted.  You should always feel confident with the vehicle and your abilities.  You should always climb hills straight up and down.  Never attempt to climb a hill on an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.", "an angle.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest", "to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or", "resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.  If You Stall Or Begin To Lose Headway If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.  Restart the engine and shift into REVERSE.  Back slowly down the hill allowing engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before", "vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.", "Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the", "the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  This mirror automatically adjusts for headlight glare from vehicles behind you.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The automatic high beam headlamp control can be turned on or off by selecting \u201con\u201d under \u201cauto dim high beams\u201d within your uconnect settings \"\u21e8uconnect settings\" , as well as turning the headlight switch to the auto position and placing the multifunction lever in the high beam position.  Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other", "will cause headlights to remain on longer (closer to the vehicle).  Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.", "Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Radio Voice Commands Use your voice to quickly get to the AM, FM, or SiriusXM\u00ae Satellite Radio stations you would like to hear.  (subscription or included siriusxm\u00ae satellite radio trial required.)  push the vr button on the steering wheel and wait for the beep to say a command.  See an example: \u201c tune to ninety-five-point-five fm\u201d \u201c tune to satellite channel hits 1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command,", "1\u201d did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Media Voice Commands Uconnect offers connections via USB, Bluetooth\u00ae, and auxiliary (AUX) ports.  Voice operation is only available for connected USB and AUX devices.  Push the vr button located on the steering wheel.  After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artist: \u201c change source to bluetooth\u00ae\u201d \u201c change source to aux\u201d \u201c change source to usb\u201d \u201c play artist beethoven\u201d; \u201c play album greatest hits\u201d; \u201c play song moonlight sonata\u201d; \u201c play genre classical\u201d did you know: press the browse button on the touchscreen to see all of the music on your usb device.  Your Voice Command must match exactly how the artist, album, song, and genre information is displayed.  Operation Voice commands can be used to operate the Uconnect Phone and to navigate its menu", "Operation Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Say compound commands like \u201cCall John Smith mobile\u201d.  Say the individual commands and allow the system to guide you to complete the task.  You will be prompted for a specific command and then guided through the available options.  Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201ccall\u201d and then \u201cjohn smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201ccall john smith mobile.\u201d for each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the", "parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  Direct Tune Press the Tune button located at the bottom of the radio screen to directly tune to a desired radio station or channel.  Press the available number button on the touchscreen to begin selecting a desired station.  Once a number has been entered, any numbers that are no longer possible (stations that cannot be reached) will become deactivated/grayed out.", "Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the GVWR Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.  Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.  The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo", "values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.  This includes driver, passengers, cargo and tongue weight.  The total load must be limited so that you do not exceed the gvwr \"\u21e8vehicle loading\" .", "See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle  The parking brake lever is located in the center console.  To apply the parking brake, pull the lever up as firmly as possible.  To release the parking brake, pull the lever up slightly, push the center button, then lower the lever completely.  When the parking brake is applied and the", "push the center button, then lower the lever completely.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the", "should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the", "in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.", "Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the striker.  How To Engage The Automatic Locking Mode Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  This indicator will illuminate when a door is ajar/open and not fully closed.  Door Latches Check for proper closing, latching, and locking.  When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle, even though the inside door lock is in the unlocked position.  After disengaging the", "door handle, even though the inside door lock is in the unlocked position.  After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the unlocked position.  After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the locked position.  For emergency exit with the system engaged, move the lock lever rearward (located on the door trim panel), lower the window and open the door with the outside door handle.  Always use this device when carrying children.  After engaging the child lock on both rear doors, check for effective engagement by trying to open a door with the internal handle.  Once the Child-Protection Door Lock system is engaged, it is impossible to open the doors from inside the vehicle.  Before getting out of the vehicle, be sure to check that there is no one left inside.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the", "anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).", "Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather.  To clear the windows, select Defrost or Mix mode and increase the front blower speed.  Do not use the Recirculation mode without A/C for long periods, as fogging may occur.  Winter Operation To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used.  Use of the Air Recirculation mode during Winter months is not recommended, because it may cause window fogging.  Half-doors \u2014 if equipped half-doors \u2014 if equipped \u00b9 use this qr code to access your digital experience.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  CAUTION: Do not run half-doors through an automatic car wash.  This may result in scratches and wax", "CAUTION: Do not run half-doors through an automatic car wash.  This may result in scratches and wax buildup on the windows.  Careless handling and storage of the half-doors may damage the seals resulting in water leaks into the interior of the vehicle.  The upper half-doors must be positioned properly to ensure sealing.  Improper installation can cause water leaks into the interior of the vehicle.  Store the zipper pulls of the upper half-door windows at the upper B-pillar area for both front and rear doors to avoid damage to the windows when not in use.  Do not attempt to operate the half-door zipper in temperatures of 41\u00b0F (5\u00b0C) or below.  Damage to the window may occur.", "Tires Examine tires for excessive tread wear and uneven wear patterns.  Check for stones, nails, glass, or other objects lodged in the tread or sidewall.  Inspect the tread for cuts and cracks.  Inspect sidewalls for cuts, cracks, and bulges.  Check the lug nut/bolt torque for tightness.  Check the tires (including spare) for proper cold inflation pressure.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the", "drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the", "If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the", "is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Replacement Tires The tires on your new vehicle provide a balance of many characteristics.  They should be inspected regularly for wear and correct cold tire inflation pressures.  The manufacturer strongly recommends using tires equivalent to the originals in size, quality, and performance when replacement is needed Refer to the Tire And Loading Information Placard or the Vehicle Certification Label for the size designation of your tire.  The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.  See the Tire Sizing Chart found in the \u201cTire Safety Information\u201d section of this manual for more information relating to the Load Index and Speed Symbol of a tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just", "tire It is recommended to replace the two front tires or two rear tires as a pair.  Replacing just one tire can seriously affect your vehicle\u2019s handling.  If you ever replace a wheel, make sure that the wheel\u2019s specifications match those of the original wheels.  It is recommended you contact an authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability.  Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.  WARNING: Do not use a tire, wheel size, load rating, or speed rating other than that specified for your vehicle.  Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.  This can cause unpredictable handling and stress to steering and suspension components.  You could lose control and have a collision resulting in serious injury or death.  Use only the", "You could lose control and have a collision resulting in serious injury or death.  Use only the tire and wheel sizes with load ratings approved for your vehicle.  Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle.  Using a tire with a smaller load index could result in tire overloading and failure.  You could lose control and have a collision Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.  CAUTION: Replacing original tires with tires of a different size may result in false speedometer and odometer readings.  What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check", "to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.", "Key Left Vehicle Feature If a valid key fob is no longer detected inside the vehicle while the vehicle\u2019s ignition system is in the ON/RUN or START position, the message \u201cKey Fob Has Left The Vehicle\u201d will be shown in the instrument cluster display along with an interior chime.  An exterior audible and visual alert will also be activated to warn the driver.  The vehicle\u2019s horn will rapidly chirp three times along with a single flash of the vehicle\u2019s exterior lights.  Note: The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Key Fob Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate", "and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  Note: The key fob\u2019s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device.  This may result in poor performance.  With the ignition in the ON/RUN position, and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.  WARNING: Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  CAUTION: The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the", "devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Note: In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery.  A low key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob.  If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.  Improper disposal of key fob batteries may be harmful to the environment.  Please see an authorized dealer for proper battery disposal \"\u21e8general information\" .  Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.  1 \u2014 Mechanical Key Release Button 2 \u2014 LED Indicator 3 \u2014 Unlock Button 4 \u2014 Lock Button 5 \u2014 Remote Start Button (If Equipped) 6 \u2014 Panic Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp", "Button Do not press the mechanical key against the START/STOP ignition button.  Do not use sharp metal objects (e.g.  screwdriver etc.)  to pry the button out of the ignition switch.  This button comes as an assembly, and is not removable.  This can damage the silicone shield.", "If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer", "recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  When using a fascia/bumper mounted ball on any model, the trailer weight is limited to 3,500 lb (1,588 kg), 30 ft 2 (2.79 m 2 ) frontal area, and 350 lb (159 kg) tongue weight.  The trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie.  the GVWR), and the GVWR should never exceed the weight referenced on the Tire And Loading Information Placard  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition", "offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  Recommended Distribution Hitch Adjustment Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the", "to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring height (h) attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control", "brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.", "Front door removal front door removal \u00b9 use this qr code to access your digital experience.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.  To remove the front doors, proceed as follows: Roll down the glass window to prevent any damage.  Remove the hinge pin nut from the upper and lower outside hinges (using a #T50 Torx head driver).  Note: the hinge pin nuts can be stowed in the fastener bin located under the rear seat.  Hinge pin nut remove the plastic wiring access door under the instrument panel by sliding the plastic panel along the door frame toward the seats until the tabs are detached.  Wiring access door note: do not force open; this will break the plastic cover.  Pull up on the red locking tab to unlock the wiring harness.  Closed wiring harness 1 \u2014 red locking tab 2 \u2014 wiring harness lever (closed position) push and hold", "Closed wiring harness 1 \u2014 red locking tab 2 \u2014 wiring harness lever (closed position) push and hold down the black security tab under the wiring harness, and lift the harness lever into the open position.  Open wiring harness 1 \u2014 wiring harness lever (open position) 2 \u2014 black security tab with the wiring harness open, pull straight downward on the wiring connector to unplug.  Store the wiring connector in the lower door basket.  With the door in the open position, remove the check screw from the door check attachment on the body side (using a #T40 Torx head driver).  Note: keep the check arm in the extended position for easier reinstallation.  See note below if the check arm gets pushed into the door while the door is off.  Door check arm with the door open, lift the door with the help of another person, to clear the hinge pins from their hinges and remove the door.  WARNING: Do not drive your vehicle on public roads with the doors removed as you will lose the protection they can provide.  This procedure is", "roads with the doors removed as you will lose the protection they can provide.  This procedure is furnished for use during off-road operation only.  Failure to follow this warning can result in death or serious personal injury.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  CAUTION: Hinge pins can break if overtightened during door reinstall (Max Torque: 5.88 ft\u00b7lb / 8 N\u00b7m).  For information on off-road driving tips, see Do not overtighten Torx fasteners.  Damage to the vehicle\u2019s parts will occur.  Note: When front doors are removed, the message \u201cBlind Spot Alert Temporarily Unavailable\u201d will display in the instrument cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  Door Frame", "cluster display.  Power Mirrors and Power Door Locks will also be unavailable.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  Door Frame Removal Using the provided #T40 Torx head driver and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per", "and ratchet, loosen the Torx head fasteners located on the underside of each door hinge (two per door), and remove the fasteners by pulling downward.  Step one note: the fasteners will not fall out once completely loose, as they are held in place by design.  Step one lift the frame upward, removing it from the vehicle.  Step two store the fasteners in a secure location.  Repeat the procedure on the front door frame.  Note: The rear door frames must be removed first, followed by the front door frames.  WARNING: Do not drive your vehicle on public roads with the door and/or door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may", "is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver", "torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can", "(ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both", "well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Lockout Service Whether the keys are locked in your vehicle or frozen locks are keeping you from getting on your way, help is just a phone call away.  This service is limited to providing access to the vehicle\u2019s seating area.  It does not cover the cost of replacement keys.  VEHICLE MAINTENANCE An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions", "Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  WARNING: You can be badly injured working on or around a motor vehicle.  Only do service work for which you have the knowledge and the proper equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will", "system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result", "to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant", "check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed", "check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.", "Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.  Towing Requirements To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended:", "break-in of your new vehicle drivetrain components, the following guidelines are recommended: WARNING: Improper towing can lead to a collision.  Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel.  When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.  You could lose control of your vehicle and have a collision.  When hauling cargo, or towing a trailer, do not overload your vehicle or trailer.  Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.  Safety chains must always be used between your vehicle and trailer.  Always connect the chains to the frame or hook retainers of the vehicle hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be", "trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be parked on a grade.  When parking, apply the parking brake on the tow vehicle.  Put the tow vehicle transmission in PARK.  Always block or \"chock\" the trailer wheels.  GCWR must not be exceeded.  Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: gvwr gtw gawr tongue weight rating for the trailer hitch utilized caution: do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven.  The engine, axle or other parts could be damaged.  Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.  This helps the engine and other parts of the vehicle wear in at the heavier loads.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for", "backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s", "Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.", "The ParkSense Park Assist system provides visual and audible indications of the distance between the rear and/or front fascia/bumper and a detected obstacle when backing up or moving forward (e.g.  during a parking maneuver).  For system limitations and usage precautions, see ParkSense will turn off the Front Park Assist audible alert (chime) after approximately three seconds when an obstacle has been detected, the vehicle is stationary, and the brake pedal is applied.  ParkSense can be active only when the gear selector is in REVERSE or DRIVE.  If ParkSense is enabled at one of these gear selector positions, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above.  A warning will appear in the instrument cluster display indicating the vehicle is above ParkSense operating speed.  The system will become active again if the vehicle speed is decreased to less than approximately 6 mph (9 km/h).  The ParkSense Warning screen is located within the instrument", "than approximately 6 mph (9 km/h).  The ParkSense Warning screen is located within the instrument cluster display It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.  ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles.  Parking curbs might be temporarily detected or not detected at all.  Obstacles located above or below the sensors will not be detected when they are in close proximity.  The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected.  It is recommended that the driver looks over his/her shoulder when using ParkSense.  Setting Name Description Forward Collision Warning Sensitivity This setting will change the distance at which the Forward Collision Warning (FCW) alert sounds.  The \u201cMedium\u201d setting will have the FCW system signal when an object is in view, and the possibility of a collision is", "will have the FCW system signal when an object is in view, and the possibility of a collision is detected.  The \u201cNear\u201d setting will have the FCW system signal when the object is closer to the vehicle.  The \u201cFar\u201d setting will have the FCW system signal when an object is at a far distance from the vehicle.  Forward Collision Warning This setting will turn the Forward Collision Warning system on or off.  The \u201cOff\u201d setting will deactivate the FCW system.  The \u201cWarning Only\u201d setting will provide only an audible chime when a collision is detected.  The \u201cWarning + Active Braking\u201d setting will provide an audible chime and apply some brake pressure when a collision is detected.  ParkSense This setting will change the type of ParkSense alert when a close object is detected and can provide both an audible chime and a visual display when an object is detected.  Front ParkSense Volume This setting adjusts the volume of the Front ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Rear ParkSense", "Front ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Rear ParkSense Volume This setting adjusts the volume of the Rear ParkSense system.  The available settings are \u201cLow\u201d, \u201cMedium\u201d, and \u201cHigh\u201d.  Blind Spot Alert This setting will change the type of alert provided when an object is detected in a vehicle\u2019s blind spot.  The \u201cOff\u201d setting will turn off Blind Spot Alert.  The \u201cLights\u201d setting will activate the Blind Spot Alert lights on the outside mirrors.  The \u201cLights & Chime\u201d setting will activate both the lights on the outside mirrors and an audible chime.  Hill Start Assist This setting will turn the Hill Start Assist system on or off.  ParkView Backup Camera Active Guidelines This setting will turn the ParkView Backup Camera Active Guidelines on or off.  ParkView Backup Camera Delay This setting will add a timed delay to the ParkView Backup Camera when shifting out of REVERSE.  Fixed ParkView Backup Camera Guidelines This setting will turn the Fixed ParkView Backup Camera", "Fixed ParkView Backup Camera Guidelines This setting will turn the Fixed ParkView Backup Camera Guidelines on or off.  Front Camera Gridlines This setting will turn the Front Camera Gridlines on or off.  Tire Fill Assist This setting will turn Tire Fill Assist on or off.  ParkSense Sensors The four ParkSense sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 79 inches (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.  The six ParkSense sensors, located in the front fascia/bumper, monitor the area in front of the vehicle that is within the sensors\u2019 field of view.  The sensors can detect obstacles from approximately 12 inches (30 cm) up to 47 inches (120 cm) from the front fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.", "in the horizontal direction, depending on the location, type and orientation of the obstacle.  ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster displayIt provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.", "Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the", "windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the", "EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present", "will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a", "engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  When Remote Start is active, and the outside ambient temperature is 40\u00b0F (4.5\u00b0C) or below, the system will automatically activate front defrost for 15 minutes or less.  The time is dependent on the ambient temperature.  Once the timer expires, the system will automatically adjust the", "on the ambient temperature.  Once the timer expires, the system will automatically adjust the settings depending on ambient conditions.  See \u201cRemote Start Comfort Systems \u2014 If Equipped\u201d in the next section for detailed operation.  The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle.  Once the ignition is placed in the ON/RUN position, the climate controls will resume previously set operations (temperature, blower control, etc.).  To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped).  Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.  These features will stay on through the duration of Remote Start, or until the ignition", "button.  These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.  With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, seeHow long does it take to remotely start my vehicle?  Depending on various conditions, it can take three minutes or more for the request to get", "vehicle?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will remote start your vehicle more quickly.  However its range is limited.  For example, when you are leaving the stadium after the game, you can use the Vehicle Branded App to remote start your vehicle and have the inside of your vehicle comfortable by the time you get to it.  Will my vehicle be safe if I lose my wireless device?  People sometimes lose their wireless devices, which is why security measures have been engineered into the Vehicle Branded App.  Asking for your username, password and SiriusXM Guardian\u2122 Security PIN help to ensure that nobody can start your vehicle if they happen to find your device.  Can someone drive off with my vehicle using the App?  nob Driving your vehicle still requires the keys to be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the", "be in the vehicle.  The Remote Start feature simply starts the engine to warm up or cool down the interior before you arrive.  Can I stop a vehicle that is being driven with the cancel Remote Vehicle Start command?  nob If the vehicle is in motion, the cancel Remote Vehicle Start button will not stop the vehicle.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.", "If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If installing the soft top immediately after removing the hard top, ensure the wire", "will occur.  If installing the soft top immediately after removing the hard top, ensure the wire harness is stored properly, and not tucked under the belt rail Provided Tools For your convenience, a tool kit is provided with your vehicle located in the center console.  This kit includes the necessary tools required for the operations described in the following sections.  All pieces fit into the ratchet for easy use.  If your vehicle is equipped with a Dual Top, the soft top system will be provided in a separate box located in the bed of the vehicle for shipping purposes only.  Note: The soft top and the hard top are to be used independently.  Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard topTo install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.", "while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.  If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and across", "the vehicle while making sure that the top is sitting flush with the body at the sides and across the back.  Then follow the removal steps in reverse order.  The Torx head fasteners that attach the hard top to the body should be torqued to 155 in-lb +/- 22 in-lb (17.5 N\u00b7m +/- 2.5 N\u00b7m) using the provided #T50 Torx head driver and ratchet.  Note: Inspect the hard top seals for damage and replace if necessary.  Install the hard top using the same steps for removal in reverse order.  When reinstalling the interior soft trim panel: be sure the panel is centered so that there is an even gap on both sides.  Apply pressure over the hook-and-loop fasteners to ensure they are properly secured.  CAUTION: Do not overtighten Torx fasteners.  Damage to the retainers will occur.", "Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.", "the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This warning light will indicate when", "the heater/air conditioning (hvac) air flow will be reduced.  This warning light will indicate when the Electronic Stability Control system is Active.  The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated.  It should go out with the engine running.  If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system.  If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.  If there is a malfunction in the Stop/Start system, the system will not shut down the engine.  A \u201cSERVICE STOP/START SYSTEM\u201d message and a yellow Stop/Start telltale will appear in the instrument cluster display If an obstacle is detected in the center front region, the display will show a", "cluster display If an obstacle is detected in the center front region, the display will show a single solid arc in the center front region with no chime.  As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and a fast sound tone will be heard and will change from fast, to continuous.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling", "A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine", "shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull", "with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Instrument cluster descriptions tachometer indicates the engine speed in revolutions per minute (rpm x 1000).  Caution: do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature gauge the temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the", "gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Caution: driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument cluster display the instrument cluster display features a driver", "dealer for service.  Instrument cluster display the instrument cluster display features a driver interactive display.  Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer indicates vehicle speed.", "Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.  It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.  If you detect any stone chips or scratches in the paint, touch them up immediately.  If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special", "paint and protective coating, have your vehicle repaired as soon as possible.  If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.  If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.  Use Mopar\u00ae Touch Up Paint on scratches as soon as possible.  An authorized dealer has touch up paint to match the color of your vehicle.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.", "on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage", "tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.", "Drag & Drop Menu Bar The Uconnect features and services in the main menu bar are easily customized for your preference.  Simply follow these steps: press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Note: This feature is only available if the vehicle is in PARK.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the", "the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE", "more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also", "of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up", "press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.", "Brake System In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervals WARNING: Riding the brakes can lead to brake failure and possibly a collision.  Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.  You would not have your full braking capacity in an emergency.  In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervalsYour vehicle is equipped with dual hydraulic brake systems.  If either of the two hydraulic systems lose normal capability, the remaining system will still function.  However, there will be some loss of overall braking effectiveness.  You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.  If the driver does not", "to slow or stop, and potential activation of the Brake Warning Light.  If the driver does not take action based upon these progressive warnings, then the system will provide a limited level of active braking to help slow the vehicle and mitigate the potential forward collision.  If the driver reacts to the warnings by braking and the system determines that the driver intends to avoid the collision by braking but has not applied sufficient brake force, the system will compensate and provide additional brake force as required.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must", "the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user's safety or the safety of others.  Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle", "the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The ACC system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.", "The system automatically prevents wheel lock and enhances vehicle control during braking.  BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems.  If either of the two hydraulic systems lose normal capability, the remaining system will still function.  However, there will be some loss of overall braking effectiveness.  You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Light.  In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function.  However, the effort required to brake the vehicle will be much greater than that required with the power system operating.  Brake System In order to ensure brake system performance, all brake system components should be inspected periodically.  For the proper maintenance intervals WARNING: Riding the brakes can lead to brake failure and possibly a collision.  Driving with your foot", "Riding the brakes can lead to brake failure and possibly a collision.  Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.  You would not have your full braking capacity in an emergency.  Brake Assist System (BAS) The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is", "pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  WARNING: The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.  BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.  The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user's safety or the safety of others.", "The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob,", "stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are", "for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a", "arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.", "of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The procedure on how to program HomeLink\u00ae to a miscellaneous device follows the same procedure as programming to a garage door opener Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.  HomeLink\u00ae replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting, or home security systems.  The HomeLink\u00ae unit is powered by your vehicle\u2019s 12 Volt battery.  The HomeLink\u00ae buttons that are located in the overhead console or sunvisor designate the three different HomeLink\u00ae channels.  To operate HomeLink\u00ae, push and release any of the programmed HomeLink\u00ae buttons.  These buttons will activate the devices", "push and release any of the programmed HomeLink\u00ae buttons.  These buttons will activate the devices they are programmed to with each press of the corresponding HomeLink\u00ae button.  The HomeLink\u00ae indicator light is located above the center button.  Place the ignition in the ON/RUN position.  Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink\u00ae button you wish to program while keeping the HomeLink\u00ae indicator light in view.  Continue to press and hold the HomeLink\u00ae button, while you press and release (cycle) your hand-held transmitter every two seconds until HomeLink\u00ae has successfully accepted the frequency signal.  The indicator light will flash slowly and then rapidly when fully trained.  Watch for the HomeLink\u00ae indicator to change flash rates.  When it changes, it is programmed.  It may take up to 30 seconds or longer in rare cases.  The garage door may open and close while you are programming.  Press and hold the programmed HomeLink\u00ae button and observe the indicator light.  If the", "Press and hold the programmed HomeLink\u00ae button and observe the indicator light.  If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink\u00ae button is pressed.  To program the two remaining HomeLink\u00ae buttons, repeat each step for each remaining button.  DO NOT erase the channels.", "Water In Fuel Indicator Light \u2014 If Equipped The Water In Fuel Indicator Light will illuminate when there is water detected in the fuel filter.  If this light remains on, DO NOT start the vehicle before you drain the water from the fuel filter to prevent engine damage, and please see an authorized dealer.  CAUTION: The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Water In Fuel Indicator Light \u2014 If Equipped The Water In Fuel Indicator Light will illuminate when there is water detected in the fuel filter.  If this light remains on, DO NOT start the vehicle before you drain the water from the fuel filter to prevent", "remains on, DO NOT start the vehicle before you drain the water from the fuel filter to prevent engine damage, and please see an authorized dealer.  CAUTION: The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Draining Fuel/Water Separator Filter \u2014 Diesel Engine The fuel/water separator housing is located inside the left frame rail in front of the fuel tank.  The best access to this water drain valve is from under the vehicle.  If necessary remove the fuel filter protective cover to access the water drain valve.  If water is detected in the water separator while the engine is running, or while the ignition switch is", "is detected in the water separator while the engine is running, or while the ignition switch is in the ON position, the Water In Fuel Indicator Light will illuminate and an audible chime will be heard.  At this point you should stop the engine and drain the water from the filter housing.  Within 10 minutes of vehicle shutdown, turn the filter drain valve (located on the bottom of the filter housing) counterclockwise to drain fuel/water; allow the accumulated water to drain.  Leave the drain valve open until all water and contaminants have been removed.  When clear fuel is visible, close the drain valve by turning it clockwise.  Upon proper draining of the water from fuel filter assembly, the Water In Fuel Indicator Light will remain illuminated for approximately 10 seconds.  If the water was drained while the engine was running, the Water In Fuel Indicator Light may remain on for approximately three minutes.  If more than two ounces or 60 ml of fuel have been drained, follow the directions for Priming If The", "more than two ounces or 60 ml of fuel have been drained, follow the directions for Priming If The Engine Has Run Out Of Fuel CAUTION: Do not drain the fuel/water separator filter when the engine is running.  Diesel fuel will damage blacktop paving surfaces.  Drain the filter into an appropriate container.  Note: Care should be taken in disposing of used fluids from your vehicle.  Used fluids, indiscriminately discarded, can present a problem to the environment.  Contact an authorized dealer, service station, or government agency for advice on recycling programs and for where used fluids and filters can be properly disposed of in your area.  Yellow indicator lights 4wd indicator light  \u21e84wd indicator light \u2014 if equipped  4wd low indicator light  \u21e84wd low indicator light \u2014 if equipped  4wd part time indicator light  \u21e84wd part time indicator light \u2014 if equipped  axle locker fault indicator light  \u21e8axle locker fault indicator light \u2014 if equipped  rear axle lock indicator light  \u21e8rear axle lock indicator light \u2014", "indicator light \u2014 if equipped  rear axle lock indicator light  \u21e8rear axle lock indicator light \u2014 if equipped  front and rear axle lock indicator light  \u21e8front and rear axle lock indicator light \u2014 if equipped  forward collision warning off indicator light  \u21e8forward collision warning off indicator light \u2014 if equipped  neutral indicator light  \u21e8neutral indicator light \u2014 if equipped  sway bar indicator light  \u21e8sway bar indicator light \u2014 if equipped  off road+ indicator light  \u21e8off road+ indicator light \u2014 if equipped  cargo light on indicator light  \u21e8cargo light on indicator light  wait to start indicator light  \u21e8wait to start indicator light \u2014 if equipped  low diesel exhaust emissions additive adblue\u00ae (urea) indicator light  \u21e8low diesel exhaust emissions additive adblue\u00ae (urea) indicator light \u2014 if equipped  water in fuel indicator light.  The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel", "is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is locatedSee the following steps for refueling: If you need assistance, you can always ask Alexa for help, or complete a list of commands by saying: \u201cAlexa, ask <brand name> for help with my car.\u201d The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.", "Without The Key Fob Special care must be taken when the vehicle is towed with the ignition in the OFF position.  The only approved method of towing without the key fob is with a flatbed truck.  Proper towing equipment is necessary to prevent damage to the vehicle.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must", "If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing", "manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicleCAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.", "The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  Manual Mirror Adjustment If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The", "the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  Ignoring the Rearview Mirror light could mean you will not have SOS Call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  When the vehicle is started, the BSM Warning Light will momentarily illuminate in both outside rearview mirrors to let the driver know that the system is operational.  The BSM system sensors operate when the vehicle is in any forward gear.  When cleaning the rearview mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly", "mirror, spray cleaner on the towel or cloth that you are using.  Do not spray cleaner directly on the mirror.  Manual Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).  The mirror should be adjusted while set in the day position (toward the windshield).  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors", "dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.", "Oil Life Reset Without pushing the brake pedal, place the ignition in the ON/RUN mode (do not start the engine).  Navigate to \"Oil Life\" submenu in \"Vehicle Info\" in the instrument cluster display.  Push and hold the ok button until the gauge resets to 100%.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after", "temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Secondary Method", "(after performing the scheduled maintenance), refer to the following procedure.  Secondary Method For Oil Change Reset Procedure Without pushing the brake pedal, place the ignition in the ON/RUN position (do not start the engine).  Fully press the accelerator pedal, slowly, three times within ten seconds.  Without pushing the brake pedal, place the ignition in the OFF position.  Note: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.  If necessary, repeat this procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures", "conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern", "time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.", "Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.  CRUISE CONTROL SYSTEMS \u2014 IF EQUIPPED Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC)", "Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system: Cruise Control will keep your vehicle at a constant preset speed.  Adaptive Cruise Control (ACC) will adjust the vehicle speed up to the preset speed to maintain a distance with the vehicle ahead.  Note: In vehicles equipped with ACC, if ACC is not enabled, Fixed Speed Cruise Control will not detect vehicles directly ahead of you.  Always be aware of the feature selected.  Only one Cruise Control feature can operate at a time.  For example, if Fixed Speed Cruise Control is enabled, Adaptive Cruise Control will be unavailable, and vice versa.  Cruise Control When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  The Cruise Control buttons are located on the right side of the steering wheel.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you", "cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Using Cruise Control On Hills The transmission may downshift on hills to maintain the vehicle set speed.  The Cruise Control system maintains speed up and down hills.  A slight speed change on moderate hills is normal.  On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Cruise Control.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  CRUISE CONTROL SYSTEMS \u2014 IF EQUIPPED Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system: Cruise", "may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system: Cruise Control will keep your vehicle at a constant preset speed.  Adaptive Cruise Control (ACC) will adjust the vehicle speed up to the preset speed to maintain a distance with the vehicle ahead.  Note: In vehicles equipped with ACC, if ACC is not enabled, Fixed Speed Cruise Control will not detect vehicles directly ahead of you.  Always be aware of the feature selected.  Only one Cruise Control feature can operate at a time.  For example, if Fixed Speed Cruise Control is enabled, Adaptive Cruise Control will be unavailable, and vice versa.", "VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both", "the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the", "If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your", "involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  Some of the most important safety features in your vehicle are the restraint systems:  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  ONLY an authorized service technician should connect equipment to the OBD II connection port in order to read the VIN, diagnose, or service your vehicle.  If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: Be possible that vehicle systems, including safety related systems, could be impaired or a loss", "Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals:", "the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.", "To Arm The System Follow these steps to arm the Vehicle Security system: Make sure the vehicle\u2019s ignition is placed in the OFF position.  Perform one of the following methods to lock the vehicle: push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zonePush the lock button on the key fob.  If any doors are open, close them.  Note: The Vehicle Security system will not arm if you lock the doors using the manual door lock.  Lock press this button to lock your vehicle.  Vehicle start press this button to start your vehicle.  Horn & lights press this button to sound the horn and activate your lights.  Unlock press this button to unlock your vehicle.  Cancel vehicle start press this button to cancel remote start.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the", "power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.", "To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to", "equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the", "engine start.  At that time, the system will go into STOP/START READY.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not", "de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.  To Manually Turn Off The Stop/Start System Push the Stop/Start OFF switch (located on the switch bank).  The light on the switch will illuminate.  The \u201cStop/Start OFF\u201d message will appear in instrument cluster display within the Stop/Start section, and the autostop function will be disabled Note: The Stop/Start system will reset itself back to an ON condition every time the ignition is turned off and back on.", "The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be", "rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  Crossbars should always be used whenever cargo is placed on the roof rack.  Check the straps frequently to be sure that the load remains securely attached.  The Roof Luggage Rack is designed to allow for carrying an additional cargo load on vehicles equipped with a Hard Top.  The load carried on the roof, when equipped with a luggage rack, must not exceed 100 lb (45 kg), this includes the weight of the crossbars, and it should be uniformly distributed over the cargo area.  Cargo must be securely tied down before driving your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds,", "your vehicle.  Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.  Follow the roof rack cautions when carrying cargo on your roof rack.  To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.  Always distribute heavy loads as evenly as possible and secure the load appropriately.  Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle.  Place a blanket or other protection between the surface of the roof and the load.  Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack.  Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift.  It is recommended to not carry large flat loads, such as wood panels or surfboards, which may result in damage to the cargo or your vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional", "vehicle.  Load should always be secured to crossbars first, with tie down loops used as additional securing points if needed.  Tie loops are intended as supplementary tie down points only.  Do not use ratcheting mechanisms with the tie loops.  Check the straps frequently to be sure that the load remains securely attached.", "The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  The battery in your vehicle is located in the right rear of the engine compartment.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  The Power Distribution Center is", "the interior, on the passenger side under the instrument panel.  The Power Distribution Center is located in the engine compartment near the battery.  This center contains cartridge fuses, mini fuses, and relays.  The PDC top cover is labeled with each serviceable fuse/relay location, function, and size.  Replacing The Battery In The Key Fob The recommended replacement battery is CR2450.  Remove the back cover of the key fob by inserting a flat-blade screwdriver into the slot on the bottom of the fob.  Apply light pressure until the cover unsnaps being careful not to damage the seal.  Proceed counterclockwise (in the order shown in the following image) to loosen the remaining snaps until the battery cover can be removed.  1-3 \u2013 back cover pry points remove the depleted battery by inserting a small flat-blade screwdriver into the battery removal slot and sliding the battery forward and upward being careful not to damage the electronic board underneath.  Battery replacement install the new battery into the key", "damage the electronic board underneath.  Battery replacement install the new battery into the key fob, making sure the positive (+) side is facing up.  Slide the battery until it is seated securely below the tabs.  Reassemble the back cover making sure it is properly aligned before snapping it back in place.  Note: Customers are recommended to use a battery obtained from Mopar\u00ae.  Aftermarket coin battery dimensions may not meet the original OEM coin battery dimensions.  Perchlorate material \u2014 special handling may apply.  See www.dtsc.ca.gov/hazardouswaste/perchlorate for further information.  Do not touch the battery terminals that are on the back housing or the printed circuit board.  When a key fob battery is low, a warning will be indicated on the vehicle\u2019s instrument cluster, and the fob LED will no longer illuminate with a button push.  WARNING: The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can", "ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or", "and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast", "case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.", "WARNING LIGHTS AND MESSAGES The warning/indicator lights will illuminate in the instrument panel together with a dedicated message and/or acoustic signal when applicable.  These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner\u2019s Manual, which you are advised to read carefully in all cases.  Always refer to the information in this chapter in the event of a failure indication.  All active telltales will display first if applicable.  The system check menu may appear different based upon equipment options and current vehicle status.  Some telltales are optional and may not appear.  ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster displayIt provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle.  Screen setup push and release the up or down arrow button until the screen setup menu", "obstacle.  Screen setup push and release the up or down arrow button until the screen setup menu icon/title is highlighted in the instrument cluster display.  Push and release the ok button to enter the submenus and follow the prompts on the screen as needed.  The Screen Setup feature allows you to change what information is displayed in the instrument cluster as well as the location in which that information is displayed.  Note: The Screen Setup feature can only be used while the vehicle is not in motion.  Note: Based upon equipment options and current vehicle status, some of the features may not be available.  Instrument Cluster Display Location And Controls The Instrument Cluster Display is located in the center of the instrument cluster.  The display contains different areas of vehicle information.  The top line where Reconfigurable Telltales, Compass Direction, Outside Temperature, Time, Range, Audio Info, MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper", "MPG or Trip are displayed.  This also displays the Speedometer which is an option for the upper center reconfigurable, but is not the default.  Default setting is Menu Title.  The main display area where the menus and pop-up messages are displayed.  The lower line where telltales, menu name and menu page are displayed.  The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: up and down arrow buttons: using the up or down arrow button allow you to cycle through the main menu items.  They allow you to change the Main Screen area and Menu Title area.  Left and right arrow buttons: using the left or right arrow button allow you to cycle through the submenu screens of the main menu item.", "To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  To remove the utility rail cleats from the side", "cutout located on the left side of the rail.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and", "cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  1 \u2014 Utility Rail Detent 2 \u2014 Cleat Retainer Nut 3 \u2014 Utility Rail Cleat The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.", "Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be", "(load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's", "They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  When using a fascia/bumper mounted ball on any model, the trailer weight is limited to 3,500 lb (1,588 kg), 30 ft 2 (2.79 m 2 ) frontal area, and 350 lb (159 kg) tongue weight.  The trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie.", "tongue weight must be considered as part of the combined weight of occupants and cargo (ie.  the GVWR), and the GVWR should never exceed the weight referenced on the Tire And Loading Information Placard", "If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The", "the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye", "Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  From the Sunrider\u00ae Position, remove straps if", "put the top down or roll the rear or side curtains.  From the Sunrider\u00ae Position, remove straps if previously secured.  Step One Failure to follow the next steps could result in damage to the soft top or vehicle.  Using the side link, lift and push the soft top toward the front of the vehicle, manually guiding the top into the closed position.  Step Two Step Two From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver.  Step Three Pull the handle back upward while squeezing the hook, locking the latch into place.  Step Four It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the", "be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed", "causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may", "may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper", "into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.  Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.  Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror.  The Outside Mirrors are located on the front driver and passenger side doors, and are adjusted manually or by power adjustment (if equipped).  If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  Outside Mirrors The Outside Mirrors are located on the front driver and passenger side doors, and are adjusted manually or by power adjustment (if equipped).  To receive maximum benefit, adjust the Outside", "manually or by power adjustment (if equipped).  To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  For information on the Door Off Mirror Kit (if equipped) when the front doors are removed, see WARNING: Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.  Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.  Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror.  Outside Mirrors The Outside Mirrors are located on the front driver and passenger side doors, and are adjusted manually or by power adjustment (if equipped).  To receive maximum benefit, adjust the Outside Mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.  For information on the Door Off", "with a slight overlap of the view obtained on the inside mirror.  For information on the Door Off Mirror Kit (if equipped) when the front doors are removed, see WARNING: Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.  Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.  Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror.  Outside Mirrors With Turn Signal \u2014 If Equipped Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the upper outer corner of each mirror.  The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle.  Turning on the Hazard Warning flashers will also activate these LEDs.  Automatic Dimming Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should", "\u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  This mirror automatically adjusts for headlight glare from vehicles behind you.  The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Note: The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.", "Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The ACC system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  ACC The Adaptive Cruise Control (ACC) on/off button is pushed", "wrong or missing distance warnings.  ACC The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged  Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.  Adaptive Cruise Control (ACC) Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC ACC will allow you to keep Cruise Control engaged in light to moderate traffic conditions without the constant need to reset your speed.  ACC utilizes a radar sensor and a forward-facing camera designed to detect a vehicle directly ahead of you to maintain a set", "and a forward-facing camera designed to detect a vehicle directly ahead of you to maintain a set speed.  Note: If the ACC sensor detects a vehicle ahead, ACC will apply limited braking or accelerate (not to exceed the original set speed) automatically to maintain a preset following distance, while matching the speed of the vehicle ahead.  Any chassis/suspension or tire size modifications to the vehicle will affect the performance of the Adaptive Cruise Control and Forward Collision Warning system.  Fixed Speed Cruise Control (ACC not enabled) will not detect vehicles directly ahead of you.  Always be aware of the feature selected WARNING: Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete", "brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The acc system: does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  You should turn the ACC system off and do not use: When driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.e., in highway construction zones).  When entering a turn lane or highway off-ramp; when driving on roads that are winding, icy, snow-covered, slippery, or have steep uphill or downhill", "driving on roads that are winding, icy, snow-covered, slippery, or have steep uphill or downhill slopes.  When towing a trailer up or down steep slopes.  When circumstances do not allow safe driving at a constant speed.  Precautions While Driving With ACC In certain driving situations, ACC may have detection issues.  In these cases, ACC may brake late or unexpectedly.  The driver needs to stay alert and may need to intervene.  The following are examples of these types of situations: Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.", "STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can", "(ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both", "well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Lockout Service Whether the keys are locked in your vehicle or frozen locks are keeping you from getting on your way, help is just a phone call away.  This service is limited to providing access to the vehicle\u2019s seating area.  It does not cover the cost of replacement keys.  VEHICLE MAINTENANCE An authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.  Service Manuals are available which include detailed service information for your vehicle.  Refer to these Service Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions", "Manuals before attempting any procedure yourself.  Note: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.  WARNING: You can be badly injured working on or around a motor vehicle.  Only do service work for which you have the knowledge and the proper equipment.  If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.  STORING THE VEHICLE If you are storing your vehicle for more than 3 weeks, we recommend that you take the following steps to minimize the drain on your vehicle's battery: Disconnect the negative cable from the battery.  If your vehicle is equipped with Stop/Start system then disconnect both the main and supplemental negative battery cables.  Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.  This will", "system at idle for about five minutes in the fresh air and high blower setting.  This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Battery cable disconnect 1 \u2014 supplemental negative battery cable 2 \u2014 main negative battery cable 3 \u2014 main negative battery terminal 4 \u2014 intelligent battery sensor (ibs) warning: take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result", "to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Note: You must isolate the supplemental battery connection point, as well as the main battery terminal from the post, as shown in the image, to fully de-energize both batteries for storage.  If assistance is needed to disconnect the battery system, see an authorized dealer.  Do not disconnect the Intelligent Battery Sensor (IBS), or your Stop/Start system may not function for up to 24 hours, due to the IBS being set into learn mode.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive", "have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an", "could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to", "properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.", "Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that", "media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app", "If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.", "Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 android", "smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in", "your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on", "calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon", "Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .", "The integrated key fob contains a coin cell battery.  Do not ingest the battery; there is a chemical burn hazard.  If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.  If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.  Keep new and used batteries away from children.  If the battery compartment does not close securely, stop using the product and keep it away from children.  The battery in your vehicle is located in the right rear of the engine compartment.  Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  The Power Distribution Center is", "the interior, on the passenger side under the instrument panel.  The Power Distribution Center is located in the engine compartment near the battery.  This center contains cartridge fuses, mini fuses, and relays.  The PDC top cover is labeled with each serviceable fuse/relay location, function, and size.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.", "OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator", "establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster", "could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Secondary Battery Your vehicle may be equipped with a secondary battery used to power the Stop/Start system and the 12 Volt vehicle electrical system.  The secondary battery is located behind the wheel well for the front passenger wheel.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.", "transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast", "both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full", "operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  In the driver and outboard front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck.  Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Lumbar Support The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control", "Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  The Lumbar Support Control knob is located on the outboard side of the front driver seat.  Rotate the control forward to increase and rearward to decrease the desired amount of lumbar support.  Lumbar Support Control Knob Turning the temperature control knob clockwise increases the heating temperature and turning the temperature control knob counterclockwise decreases the heating temperature.", "With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, see These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.  How To Use Remote Start Push and release the Remote Start button on the key fob twice within five seconds.  The vehicle doors and tailgate will lock, the", "button on the key fob twice within five seconds.  The vehicle doors and tailgate will lock, the turn signals will flash twice, and the horn will chirp twice.  Pushing the Remote Start button again will shut the engine off.  All of the following conditions must be met before the engine will remote start: gear selector in park doors closed hood closed hazard switch off brake switch inactive (brake pedal not pressed) battery at an acceptable charge level panic button not pushed fuel meets minimum requirement system not disabled from previous remote start event vehicle security system not active all removable doors must not be removed malfunction indicator/check engine telltale is not illuminated water in fuel telltale is not illuminated wait to start telltale is not illuminated for additional remote start information, see.  Note: With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then", "be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  WARNING LIGHTS AND MESSAGES The warning/indicator lights will illuminate in the instrument panel together with a dedicated message and/or acoustic signal when applicable.  These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner\u2019s Manual, which you are advised to read carefully in all cases.  Always refer to the information in this chapter in the event of a failure indication.  All active telltales will display first if applicable.  The system check menu may appear different based upon equipment", "will display first if applicable.  The system check menu may appear different based upon equipment options and current vehicle status.  Some telltales are optional and may not appear.  How To Use Remote Start Push and release the Remote Start button on the key fob twice within five seconds.  The vehicle doors and tailgate will lock, the turn signals will flash twice, and the horn will chirp twice.  Pushing the Remote Start button again will shut the engine off.  All of the following conditions must be met before the engine will remote start: gear selector in park doors closed hood closed hazard switch off brake switch inactive (brake pedal not pressed) battery at an acceptable charge level panic button not pushed fuel meets minimum requirement system not disabled from previous remote start event vehicle security system not active all removable doors must not be removed malfunction indicator/check engine telltale is not illuminated water in fuel telltale is not illuminated wait to start telltale is not", "telltale is not illuminated water in fuel telltale is not illuminated wait to start telltale is not illuminated for additional remote start information, see.  Note: With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  Driver And Passenger BeltAlert \u2014 If Equipped BeltAlert is a feature intended to remind the driver and outboard front seat passenger (if equipped with outboard front passenger seat BeltAlert) to buckle their seat belts.  The Belt Alert feature is active whenever the ignition switch is in the START or ON/RUN position.", "Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  To order a hard copy of your service or diagnostic procedure manuals, visit: www.techauthority.com (us and canada).  Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  Diagnostic Procedure Manuals To order a hard copy of your Service or Diagnostic Procedure manuals, visit:", "Procedure Manuals To order a hard copy of your Service or Diagnostic Procedure manuals, visit:  To order a hard copy of your Service or Diagnostic Procedure manuals, visit: Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.  These manuals make it easy to find and fix problems on computer-controlled vehicle systems and features.  They show exactly how to find and correct problems, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.  Diagnostic Procedure Manuals Owner's Manuals, Radio Manuals and Warranty Information Books can be ordered through Archway at:", "Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side.  Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.  Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle.  If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.  Diesel Exhaust Fluid Diesel Exhaust Fluid (DEF) sometimes known simply by the name of its active component, UREA, is a key component of Selective Catalytic Reduction (SCR) systems, which help diesel vehicles meet stringent emission regulations.  DEF is a liquid reducing agent that reacts with engine exhaust in the presence of a catalyst to convert smog-forming Nitrogen Oxides (NOx) into harmless nitrogen and water vapor.  For further information  Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may", "Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side.  Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.  Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle.  If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.  Vehicle Identification Number Owner's name and address Owner's telephone number (home, mobile, and office) Authorized dealer name Vehicle Identification Number (VIN) Vehicle delivery date and mileage This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), front and rear Gross Axle Weight Rating (GAWR), and Vehicle Identification Number (VIN).  A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.  The bar code that appears on the bottom of the label is your VIN.", "REFUELING IN EMERGENCY \u2013 IF EQUIPPED The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Note: In certain cold conditions, ice may prevent the fuel door from opening.  If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button.  Do not pry on the door.  REFUELING IN EMERGENCY \u2013 IF EQUIPPED The vehicle may be equipped with a refueling funnel.  Vehicles with diesel engines will have a cap to remove to begin the refueling process.  If refueling is necessary, while using an approved gas can, insert the refueling funnel into the filler neck opening.  Take care to open both flappers with the funnel to avoid spills.  Note: In certain cold conditions, ice may prevent the", "flappers with the funnel to avoid spills.  Note: In certain cold conditions, ice may prevent the fuel door from opening.  If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button.  Do not pry on the door.  Emergency Gas Can Refueling Most gas cans will not open the flapper doors.  A funnel is provided to allow emergency refueling with a gas can.  See the following steps for refueling: Retrieve funnel from under the right rear seat.  Fuel funnel location refueling funnel remove the fuel filler cap and insert the funnel into same filler pipe opening as the fuel nozzle.  Inserting funnel ensure funnel is inserted fully to hold flapper doors open.  Pour fuel into funnel opening.  Caution: to avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  Remove funnel from filler pipe, clean off prior to putting back in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an", "in the spare tire storage area.  Tighten the fuel filler cap until clicking is heard.  This is an indication the cap is properly tightened.  WARNING: Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.  Never add fuel when the engine is running.  This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.  A fire may result if fuel is pumped into a portable container that is inside of a vehicle.  You could be burned.  Always place fuel containers on the ground while filling.  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)  REFUELING THE VEHICLE \u2014 GASOLINE ENGINE (IF EQUIPPED)", "Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Brake Warning Light This warning light", "ON/RUN mode, have the light repaired as soon as possible.  Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event", "be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If", "light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light", "is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition", "as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS", "level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If", "(ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.", "Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshield.  Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Lowering the windshield before completing the", "windshield is raised prior to installing the tops.  Lowering the windshield before completing the following steps: if your vehicle is equipped with a soft top, the top must be lowered \"\u21e8lowering the soft top\" , and the door frames must be removed \"\u21e8door frame \u2014 if equipped with a soft top\" prior to lowering the windshield.  If your vehicle is equipped with a hard top, the freedom panels must be removed prior to lowering the windshield.  Caution: failure to follow this step will cause damage to the vehicle\u2019s header seal.  Manually remove the protective caps over the windshield wiper hex bolts.  Step two 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.  Move to the inside of the vehicle and lower both sun visors.  Using the provided #T40 Torx head driver, remove the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center", "windshield (two on each side of the header trim).  Step five 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping, or in the fastener bin located below the rear seat.  Lower the windshield gently until it contacts the tie-down bumpers (if equipped).  Step six 1 \u2014 washer nozzle 2 \u2014 bumper 3 \u2014 tie-down secure the windshield by passing a cinch strap through the tie-down bumper on either side of the hood and on the windshield frame.  Tighten the strap to secure the windshield in place.  Caution: do not overtighten.  Damage to the windshield could result.  FOLDING WINDSHIELD The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element", "your vehicle on-road with the windshield down, as you lose the protection this structural element provides.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  WARNING: Carefully follow these warnings to help protect against personal injury: Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as", "vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raising The Windshield Release the strap that secured the windshield in the lowered position.  Raise the windshieldUsing the provided #T40 Torx head driver, reinstall the four Torx head fasteners located along the interior of the windshield (two on each side of the header trim).  Secure them until they are snug, being careful not to", "(two on each side of the header trim).  Secure them until they are snug, being careful not to cross-thread the fasteners or overtighten.  Step three 1 \u2014 outer torx fasteners 2 \u2014 center torx fasteners reinstall the windshield wiper arms using the provided 15 mm socket.  First, align the tips of the blade to the \u201cT\u201d mark in the glass.  Then, while holding the arm in that position, reinstall the hex nut and tighten until snug.  Be careful not to overtighten.  Repeat for the other arm.  Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.  Step five 1 \u2014 hex bolt cover installed 2 \u2014 hex bolt cover removed note: make sure the windshield is raised prior to installing the tops.  Cleaning Instructions During windshield down applications, dust/dirt can accumulate in the cover and block the camera lens.  Use a microfiber cloth to clean the camera lens, module, and inside cover, being careful not to damage or scratch the module.", "The ignition switch must be in the ACC or ON/RUN position to adjust the power mirrors.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the", "unless the driver turns the ignition OFF.  The transmission is NOT locked in PARK when the ignition is in the ACC position (even though the engine will be off).  Ensure that the transmission is in park, and the ignition is off (not in acc position) before exiting the vehicle.  After switching the ignition key from OFF to either the ON/RUN or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system Place the gear selector in PARK, then push and release the ENGINE START/STOP button.  The ignition will return to the OFF position.  If the gear selector is not in PARK (with vehicle stopped) and the ENGINE START/STOP button is pushed once, the transmission will automatically select PARK and the engine will turn off, however the ignition will remain in the ACC position (NOT the OFF position).  Never leave a vehicle out of the PARK position, or it could roll.  If the gear selector is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP", "is in NEUTRAL, and the vehicle speed is below 5 mph (8 km/h), pushing the ENGINE START/STOP button once will turn the engine off.  the ignition will remain in the ACC position If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds (or three short pushes in a row) to turn the engine off.  The ignition will remain in the ACC position (NOT the OFF position) if the engine is turned off when the transmission is not in PARK.  Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d The buttons on the right side of the steering wheel operate the ACC system.  To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The", "Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged ACC Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following appears in the instrument cluster display:  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: ENGINE START/STOP Button Functions \u2014 With Driver\u2019s Foot Off The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch.  It has three modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the", "modes: OFF, ACC, and RUN.  To change the ignition modes without starting the vehicle and use the accessories, follow these steps: Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire", "system.  In addition to the four auxiliary switch wires, a fused battery wire and ignition wire are also located in the interior, on the passenger side under the instrument panel.  After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  If there are no fuel leaks or damage to the vehicle electrical devices (e.g.  headlights) after an accident, reset the system by following the procedure described below.  If you have any doubt, contact an authorized dealer.  For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the", "completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.", "Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid", "for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.  If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  To close the tailgate, lift upward until both sides latch into place.", "Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.  OCCUPANT RESTRAINT SYSTEMS Some of the most important safety features in your vehicle are the restraint systems:  SAFETY FEATURES When the Safety/Driving Assistance button is", "vehicle are the restraint systems:  SAFETY FEATURES When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Note: depending on the vehicle\u2019s options, feature settings may vary.  OCCUPANT RESTRAINT SYSTEMS Some of the most important safety features in your vehicle are the restraint systems:", "Automatic SOS \u2014 If Equipped Automatic SOS is a hands-free safety service that can immediately connect you with help in the event that your vehicle\u2019s airbags deploy.  Please refer to your provided radio supplement for complete information.  SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant", "the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice", "with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An", "and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.", "when you need it.  You could be injured if the air bag system is not there to help protect you.  Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.", "Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.  SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of", "on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is", "the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke", "and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s", "equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  Sos call system limitations vehicles sold in mexico do not have sos call system capabilities.  SOS or other emergency line operators in Mexico may not answer or respond to SOS system calls.  If the SOS Call system detects a malfunction, any of the following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires", "be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d an in-vehicle audio message will state \u201cvehicle device requires service.  Please contact an authorized dealer.\u201d even if the sos call system is fully functional, factors beyond fca us llc\u2019s control may prevent or stop the sos call system operation.  These include, but are not limited to, the following factors: the ignition is in the off position the vehicle\u2019s electrical systems are not intact the sos call system software and/or hardware are damaged during a crash the vehicle battery loses power or becomes disconnected during a vehicle crash lte (voice/data) or 4g (data) network and/or global positioning satellite signals are unavailable or obstructed equipment malfunction at the sos operator facility operator error by the sos operator lte (voice/data) or 4g (data) network congestion weather buildings, structures, geographic terrain, or tunnels warning: ignoring the", "congestion weather buildings, structures, geographic terrain, or tunnels warning: ignoring the rearview mirror light could mean you will not have sos call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the", "serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber.  Never place anything on or near the vehicle\u2019s LTE (voice/data) or 4G (data) and GPS antennas.  You could prevent LTE (voice/data) or 4G (data) and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable LTE (voice/data) or 4G (data) network connection and a GPS signal is required for the SOS Call system to function properly.  Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.", "Adding Diesel Exhaust Fluid The DEF gauge (located on the instrument cluster display) will display the level of DEF remaining in the tankNote: Driving conditions (altitude, vehicle speed, load, etc.)  will affect the amount of DEF that is used in your vehicle.  System Overview This vehicle is equipped with a Diesel Exhaust Fluid (DEF) injection system and a Selective Catalytic Reduction (SCR) catalyst to meet the emission requirements.  The def injection system consists of the following components: def tank def pump def injector electronically-heated def lines nox sensors temperature sensors scr catalyst the def injection system and scr catalyst enable the achievement of diesel emissions requirements; while maintaining outstanding fuel economy, drivability, torque and power ratings.  For system messages and warnings see Note: Your vehicle is equipped with a DEF injection system.  You may occasionally hear an audible clicking noise from under the vehicle at a stop.  This is normal operation.  The DEF pump", "audible clicking noise from under the vehicle at a stop.  This is normal operation.  The DEF pump will run for a period of time after engine shutdown to purge the DEF system.  This is normal operation and may be audible from the rear of the vehicle.  DEF tank DEF pump DEF injector Electronically-heated DEF Lines NOx sensors Temperature sensors SCR catalyst DEF is subject to freezing at the lowest temperatures.  For example, DEF may freeze at temperatures at or below 12\u00b0F (-11\u00b0C).  The system has been designed to operate in this environment.  Any containers or parts that come into contact with DEF must be DEF compatible (plastic or stainless steel).  Copper, brass, aluminum, iron or non-stainless steel should be avoided as they are subject to corrosion by DEF.  If DEF is spilled, it should be wiped up completely.  The DEF gauge (located on the instrument cluster display) will display the level of DEF remaining in the tank", "Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio.  This condition may be lessened or eliminated by repositioning the mobile phone within the vehicle.  This condition is not harmful to the radio.  If your radio performance does not satisfactorily improve from repositioning the mobile phone, it is recommended that the volume be turned down or off during mobile phone operation when not using the Uconnect system.  Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors.  Installing some form of aftermarket window tinting that affects radio wave signals.  Lots of snow or ice around the wheels or wheel housings.  Using tire chains on the vehicle.  Using wheels/tires not equipped with TPMS sensors.  The radio unit is acting as the amplifier for audio output from the Auxiliary device.  Therefore, if the volume control on the Auxiliary device is set too low, there will be", "device.  Therefore, if the volume control on the Auxiliary device is set too low, there will be insufficient audio signal for the radio unit to play the music on the device.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn", "on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have", "good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and", "Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW", "temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring Height (H) Attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Trailer And Tongue Weight Never exceed the maximum tongue weight stamped on your bumper or trailer hitch.  Consider the following items when computing the weight on the", "on your bumper or trailer hitch.  Consider the following items when computing the weight on the rear axle of the vehicle: the tongue weight of the trailer the weight of any other type of cargo or equipment put in or on your vehicle the weight of the driver and all passengers note: remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.", "If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.", "tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a", "console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.", "For information on the Door Off Mirror Kit (if equipped) when the front doors are removed, see If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Door Off Mirror To install the Door Off Mirrors, proceed as follows:  Door Off Mirror Kit \u2014 If Equipped If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  To install the Door Off Mirrors, proceed as follows: Remove both front doorsRemove the cowl bolt closest to the door opening using a #40 Torx head driver, and store in a safe location.  Cowl bolt location push the mirror bracket forward onto the a-pillar, making sure to align the bottom of the bracket with the upper door hinge, and the hole from the removed cowl bolt.  Push bracket onto a-pillar place the bracket bushing behind the mirror bracket (over the cowl bolt hole), then insert the bracket", "the bracket bushing behind the mirror bracket (over the cowl bolt hole), then insert the bracket bolt into the mirror bracket, through the bracket bushing.  Attaching mirror bracket to the vehicle 1 \u2014 bracket bushing 2 \u2014 bracket bolt insert the hinge shoulder bolt through the bottom of the upper door hinge up into the mirror bracket, then rotate the bracket knob toward the rear of the vehicle to secure the mirror bracket to the a-pillar.  Attaching mirror bracket to the vehicle 1 \u2014 bracket knob 2 \u2014 hinge shoulder bolt tighten both the bracket bolt and the hinge shoulder bolt with a #40 torx head driver.  Recommended torque specification for the bracket bolt is 6 ft-lb (8 N\u00b7m), and 7.5 ft-lb (10 N\u00b7m) for the hinge shoulder bolt.  Lower the mirror assembly onto the mirror bracket.  Lower mirror assembly onto bracket insert the three mirror screws into the mirror assembly, and tighten into the mirror bracket using a #30 torx head driver.  Recommended torque specification for the mirror screws is 4 ft-lb (5.5", "a #30 torx head driver.  Recommended torque specification for the mirror screws is 4 ft-lb (5.5 N\u00b7m).  Mirror screw locations repeat the steps on the other side of the vehicle.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For off-road driving tips, see Do not store detached doors inside of the vehicle, as they may fly around and cause personal injury or death in the event of a sudden stop, rough terrain, or a collision.  Note: If this kit is being installed with the optional lamp bracket, the bracket bushing from step 4 is not needed.  Use the spacer from the lamp bracket.  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an", "Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.", "A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into", "the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Press and release this button to turn the Climate Control ON/OFF.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  To Turn Off The Engine Using The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C", "The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control will turn off, but Stability Control will remain active.  Hold the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner", "the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  A/C Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Note: For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the", "seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.", "Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Extreme Cold Weather The cartridge block heater", "are available from an authorized Mopar\u00ae dealer.  Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.", "equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and", "plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of", "vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available", "at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine", "the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Turn off the Fuel Filter Heater, Turn off the HVAC Blower Motor, Close the HVAC Circulation Door Cut off battery power to the: Engine Electric Motor (if equipped) Electric power steering Brake booster Electric park brake Automatic transmission gear selector Horn Front wiper", "Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry (If Equipped) The Passive Entry system is a feature that allows you to lock and unlock the vehicle\u2019s door(s) and tailgate without having to push the key fob lock or unlock buttons.  Note: Passive Entry may be programmed on/off through Uconnect Settings The key fob may not be detected by the vehicle Passive Entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may interfere with the key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.  Passive Entry Unlock initiates Headlight Illumination On Approach (low beams, license plate lamp, parking lights) for whichever duration is set within the Uconnect Settings between 0, 30, 60 or 90 seconds.  Passive Entry Unlock also initiates two flashes of the turn signal lights.  If wearing gloves, if it has been raining/snowing, or there is salt/dirt covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a", "covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.  The doors may unlock when water is sprayed on the Passive Entry door handles if the key fob is located outside of the vehicle within 5 ft (1.5 m) of the handle.  If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will relock and, if equipped, will arm the Vehicle Security system.  Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry (If Equipped) The Passive Entry system is a feature that allows you to lock and unlock the vehicle\u2019s door(s) and tailgate without having to push the key fob lock or unlock buttons.  Note: Passive Entry may be programmed on/off through Uconnect Settings The key fob may not be detected by the vehicle Passive Entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may interfere with the key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.", "key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.  Passive Entry Unlock initiates Headlight Illumination On Approach (low beams, license plate lamp, parking lights) for whichever duration is set within the Uconnect Settings between 0, 30, 60 or 90 seconds.  Passive Entry Unlock also initiates two flashes of the turn signal lights.  If wearing gloves, if it has been raining/snowing, or there is salt/dirt covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.  The doors may unlock when water is sprayed on the Passive Entry door handles if the key fob is located outside of the vehicle within 5 ft (1.5 m) of the handle.  If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will relock and, if equipped, will arm the Vehicle Security system.  Frequency Operated Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive", "Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.  FOBIK-Safe only executes in vehicles with Passive Entry.  There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made by a valid Passive Entry key fob while a door is open.  A lock request is made by the Passive Entry door handle while a door is open.  A lock request is made by the door panel switch while the door is open.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  Note: The", "system, the key fob protection described in this section remains active/functional.  Note: The vehicle will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle.  The vehicle will not unlock the doors when any of the following conditions are true: A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are manually locked using the door lock knobs.  Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.  To Lock The Vehicle\u2019s Doors With one of the vehicle\u2019s Passive Entry key fobs within 5 ft (1.5 m) of the driver or passenger front door handles, pushing the Passive Entry lock button will lock the vehicle doors.  Note: When pushing the door handle lock button, DO NOT grab the door handle.  This could unlock the door(s).  Note: After pushing the door handle button, the driver must wait three seconds before locking or", "Note: After pushing the door handle button, the driver must wait three seconds before locking or unlocking the doors, using any Passive Entry door handle.  This is done to allow the driver to check if the vehicle is locked by pulling the door handle without the vehicle unlocking.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in \u201cPreventing Inadvertent Locking Of Passive Entry Key Fob In Vehicle\u201d remains active/functional.  The Passive Entry system will not operate if the key fob battery is depleted  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking", "system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the", "parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  When the parking brake is applied", "illuminate, have the light inspected by an authorized dealer.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  If the headlights or parking lights are left on after the ignition is placed in the OFF position, the vehicle will chime when the driver\u2019s door is opened.  Vehicle parking brake is applied Stability event occurs Gear selector is moved out of DRIVE Engine overspeed occurs Clutch pedal is pressed (manual transmission only) Vehicle is operating at a low RPM (manual transmission only) Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before", "crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  release the parking brake  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and", "Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will", "is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following:  Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving,", "on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately \"\u21e8air bag warning light\" .", "The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  Power Window Switches Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel", "10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.  Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.", "front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.", "Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable", "battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain", "could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump", "pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other", "explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an", "fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.  Note: Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle while making connections.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so", "or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.", "To Deactivate A soft tap on the brake pedal, pushing the CANC (cancel) button, or normal brake pressure while slowing the vehicle will deactivate the Cruise Control without erasing the set speed from memory.  The following conditions will also deactivate the cruise control without erasing the set speed from memory: vehicle parking brake is applied stability event occurs gear selector is moved out of drive engine overspeed occurs clutch pedal is pressed (manual transmission only) vehicle is operating at a low rpm (manual transmission only) pushing the on/off button or placing the ignition in the off position, erases the set speed from memory.  Adaptive Cruise Control Off When ACC is deactivated, the display will read \u201cAdaptive Cruise Control Off.\u201d To Deactivate A soft tap on the brake pedal, pushing the CANC (cancel) button, or normal brake pressure while slowing the vehicle will deactivate the Cruise Control without erasing the set speed from memory.  The following conditions will also deactivate the cruise", "erasing the set speed from memory.  The following conditions will also deactivate the cruise control without erasing the set speed from memory: vehicle parking brake is applied stability event occurs gear selector is moved out of drive engine overspeed occurs clutch pedal is pressed (manual transmission only) vehicle is operating at a low rpm (manual transmission only) pushing the on/off button or placing the ignition in the off position, erases the set speed from memory.  To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d WARNING: Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous.  You could accidentally set the system or cause it to go faster than you", "not in use is dangerous.  You could accidentally set the system or cause it to go faster than you want.  You could lose control and have a collision.  Always leave the system off when you are not using it.  When ACC is deactivated, the display will read \u201cAdaptive Cruise Control Off.\u201d The following conditions will also deactivate the Cruise Control without erasing the set speed from memory: When the condition that deactivated the system is no longer present, the system will return to the \u201cAdaptive Cruise Control Off\u201d state and will resume function by simply reactivating it.  A soft tap on the brake pedal, pushing the CANC (cancel) button, or normal brake pressure while slowing the vehicle will deactivate the Cruise Control without erasing the set speed from memory.  Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will", "and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.", "Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat buildup may cause serious injury or death.  It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.  In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.  Be sure everyone in your vehicle is in a seat and using a seat belt properly.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and", "contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or", "Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of", "instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.", "If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before driving down a steep hill, you need to determine if it is too steep for a safe descent.  What is the surface traction?  Is the grade too steep to maintain a slow, controlled descent?  Are there obstacles?  Is it a straight descent?  Is there plenty of distance at the base of the hill to regain control if the vehicle descends too fast?  If you feel confident in your ability to proceed, then make sure you are in 4L and proceed with caution.  Allow engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  Moving from a high gear down to a lower", "brakes, if necessary, but do not allow the tires to lock.  Moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills.  In addition, downshifting at the right time provides better acceleration when you desire to resume speed.  Downshift progressively.  Do not skip gears to avoid overspeeding the engine and clutch.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Downhill Before driving down a steep hill, you need to determine if it is too steep for a safe descent.  What is the surface", "a steep hill, you need to determine if it is too steep for a safe descent.  What is the surface traction?  Is the grade too steep to maintain a slow, controlled descent?  Are there obstacles?  Is it a straight descent?  Is there plenty of distance at the base of the hill to regain control if the vehicle descends too fast?  If you feel confident in your ability to proceed, then make sure you are in 4L and proceed with caution.  Allow engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: Do not descend a steep grade in NEUTRAL.  Use vehicle brakes in conjunction with engine braking.  Descending a grade too fast could cause you to lose control and be seriously injured or killed.  Off-Road Driving Tips  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the", "possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which", "or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.", "Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the", "the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.", "To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  When a door is", "system, the key fob protection described in this section remains active/functional.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless", "is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is", "devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.", "The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument", "must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The Autostop Mode, The Following Must Occur: Conditions That Will Cause The Engine To Start Automatically While In Autostop Mode: To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: Conditions that will cause the engine to start automatically while in STOP/START AUTOSTOP ACTIVE mode, the engine will start automatically when: This indicator light will illuminate when the Stop/Start function is in \u201cAutostop\u201d mode.  The Stop/Start feature is enabled after every normal engine start.  It will", "is in \u201cAutostop\u201d mode.  The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  While in an Autostop, the Climate Control system may automatically adjust airflow to maintain cabin comfort.  Customer settings will be maintained upon return to an engine running condition.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This light alerts the driver that the vehicle is in", "conditioning (hvac) air flow will be reduced.  This light alerts the driver that the vehicle is in the neutral mode", "To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when", "20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set", "ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speed  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed", "show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which", "sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full", "operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the", "start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: The message will stay active until the ignition is placed in the ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP", "ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  To insert an Auxiliary device, gently insert the Auxiliary device cable into the AUX port.  If you insert an Auxiliary device with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system", "with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is", "which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on", "obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "Daytime Running Lights (DRLs) \u2014 If Equipped The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  Note: For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be", "Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  BeltAlert can be activated or deactivated by an authorized dealer.  FCA US LLC does not recommend deactivating BeltAlert.  The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are", "are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  \"R\" means radial construction, or \"D\" means", "(when the hazard warning lights are activated).  \"R\" means radial construction, or \"D\" means diagonal or bias construction Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered in the US and other countries.  Apple\u00ae terms of use and privacy statements apply.", "Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND", "function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.  Windshield Washers To use the washer, pull the lever toward you and hold until desired spray is reached.  If the lever is pulled while in the delay range, the wiper will start and continue to operate for two or three wipe cycles after the lever is released.  Then, the intermittent interval previously selected will resume.  If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles.  Then, the wipers will turn off.  Note: As a protective measure, the washer will stop if the switch is held for more than 20 seconds.  Once the switch is released the washer will resume normal operation.  WARNING: Sudden loss of visibility through the windshield", "the washer will resume normal operation.  WARNING: Sudden loss of visibility through the windshield could lead to a collision.  You might not see other vehicles or other obstacles.  To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.", "If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The", "the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye", "Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if", "that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.", "may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be", "on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or", "any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended", "cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  If you get hung up or high-centered on an object,", "jacking on locations other than those indicated.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.", "get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand,", "brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change", "changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.", "Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set", "the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.", "Shifting Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident,", "recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall", "DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals", "Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.", "Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  Tonneau Cover Removal To remove the", "straps are secure, before removing.  Store in a safe location.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.", "be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll", "straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be", "Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed),", "both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the", "cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the", "there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "Heated Seats \u2014 If Equipped The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  Press the heated seat button once to turn the HI setting on.  Press the heated seat button a second time to turn the MED setting on.  Press the heated seat button a third time to turn the LO setting on.  Press the heated seat button a fourth time to turn the heating elements off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated seats to operate.  The level of heat selected will stay on until the operator changes it.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.  It may cause burns even at low temperatures, especially if used for long periods of time.  Do not place anything on the seat or", "temperatures, especially if used for long periods of time.  Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion.  This may cause the seat heater to overheat.  Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.  Setting name description auto-on driver heated/ventilated seat & heated steering wheel with vehicle start this setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  Remote Start Comfort Systems \u2014 If Equipped When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and", "front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The", "started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  The engine must be running for the heated steering wheel to operate.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel", "as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  The engine must be running for the heated seats to operate.  The level of heat selected will stay on until the operator changes it.  Heated Seat/Vented Seats/Heated Wheel Rear Defroster And Heated Mirrors HVAC System 115 Volt AC Power Inverter System Audio and Telematics System  Setting name description auto-on driver heated/ventilated seat & heated steering wheel with vehicle start this setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote", "the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.", "Half-Door Installation To install the front or rear half-doors, proceed as follows: Remove the full doors from the vehicle.  For front door removal, see For rear door removal, see Locate the upper and lower hinge pins on the lower half-door, and lower them into the body hinges on the vehicle.  Note: the upper hinge pin is longer, which can be used to assist in guiding the door into place during installation.  Lower half-door hinge pins insert the upper and lower hinge pin screws into the body hinges.  Tighten the screws using a #T50 Torx head driver to 3.8 ft\u00b7 lb / 5.2 N\u00b7m.  Caution: do not close the door before reattaching the door check to the body.  Damage may occur to the door check.  Do not overtighten Torx fasteners, damage to the vehicle\u2019s parts will occur.  Hinge pins can break if overtightened during door install (Max Torque: 6.0 ft\u00b7 lb/8.1 N\u00b7m).  Attach the cloth strap of the lower half-door to the metal hook just inside the vehicle.  Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap connect", "metal hook just inside the vehicle.  Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap connect the wiring harness on the lower half-door to the connection just inside the vehicle.  Note: for front doors, make sure the wiring harness is closed completely.  Front door wiring harness 1 \u2014 open wiring harness 2 \u2014 closed wiring harness replace wiring access doors.  When the half-doors are shipped with the vehicle, the lower half-doors will have plugs in the post holes that must be removed prior to upper half-door installation.  To remove these plugs, proceed as follows: locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place tool into service hole of plug to remove using the tool, slowly pull upwards from the center of the plug to remove.  Making sure the window on the upper half-door is completely zipped closed, insert the upper half-door into the lower half-door by placing", "is completely zipped closed, insert the upper half-door into the lower half-door by placing the posts into the post holes.  Lower the upper half-door into post holes push down firmly on the inside of the upper half-door until it is fully seated in the lower half.  Push Down To Fully Seat Upper Half-Door  To remove the half-doors, repeat the installation steps in reverse order.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners", "for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  If the check arm is stuck inside the door, follow these instructions to install the check arm.  To reinstall the door(s), perform the previous steps in the reverse", "to install the check arm.  To reinstall the door(s), perform the previous steps in the reverse order.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  To install the front door exterior mirrors on the half-doors, proceed as follows: To install the front or rear half-doors, proceed as follows: Locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place Tool Into Service Hole Of Plug To Remove Using the tool, slowly pull upwards from the center of the plug to remove.  Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the", "striker.  Touch condition between these components can result in damage to both the door and the striker.  Only adjust the door to fit correctly against the striker.  DO NOT adjust the striker, as this could affect the positioning of the full door.  Half-doors \u2014 if equipped half-doors \u2014 if equipped \u00b9 use this qr code to access your digital experience.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  CAUTION: Do not run half-doors through an automatic car wash.  This may result in scratches and wax buildup on the windows.  Careless handling and storage of the half-doors may damage the seals resulting in water leaks into the interior of the vehicle.  The upper half-doors must be positioned properly to ensure sealing.  Improper installation can cause water leaks into the interior of the vehicle.  Store the zipper pulls of the upper", "can cause water leaks into the interior of the vehicle.  Store the zipper pulls of the upper half-door windows at the upper B-pillar area for both front and rear doors to avoid damage to the windows when not in use.  Do not attempt to operate the half-door zipper in temperatures of 41\u00b0F (5\u00b0C) or below.  Damage to the window may occur.", "Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial", "DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When", "the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Requirements To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended: WARNING: Improper towing can lead to a collision.  Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel.  When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.  You could lose control of your vehicle and have a collision.  When hauling cargo, or towing a trailer, do not overload your vehicle or trailer.  Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis", "poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.  Safety chains must always be used between your vehicle and trailer.  Always connect the chains to the frame or hook retainers of the vehicle hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be parked on a grade.  When parking, apply the parking brake on the tow vehicle.  Put the tow vehicle transmission in PARK.  Always block or \"chock\" the trailer wheels.  GCWR must not be exceeded.  Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: gvwr gtw gawr tongue weight rating for the trailer hitch utilized caution: do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven.  The engine, axle or other parts could be damaged.  Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50", "damaged.  Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.  This helps the engine and other parts of the vehicle wear in at the heavier loads.", "When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.", "jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or", "with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash", "other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.", "connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the", "post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.", "Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.  Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The ACC system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions,", "adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  ACC The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged  Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.", "Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must", "spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  Press the heated steering wheel button once to turn the heating element on.", "wheel if equipped.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to", "or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The engine must be running for the heated steering wheel to operate.", "Anti-Lock Brake System (ABS) Warning Light This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However,", "anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate", "is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should", "by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  This warning light will turn on when there's a fault with the EPS system", "When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Depending on the vehicle\u2019s options, feature settings may vary.  Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Depending on the vehicle\u2019s options, feature settings may vary.  When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Note: depending on the vehicle\u2019s options, feature settings may vary.  When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system", "on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Note: depending on the vehicle\u2019s options, feature settings may vary.  Adjustable Chime Volume Settings The Front and Rear chime volume settings are programmable.  The settings may be programmed through the Uconnect system The chime volume settings include low, medium, and high.  The factory default volume setting is medium.  ParkSense will retain its last known configuration state through ignition cycles.  When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will", "access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Note: depending on the vehicle\u2019s options, feature settings may vary.", "Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result", "up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Downhill Before driving down a steep hill, you need to determine if it is too steep for a safe descent.  What is the surface traction?  Is the grade too steep to maintain a slow, controlled descent?  Are there obstacles?  Is it a straight descent?  Is there plenty of distance at the base of the hill to regain control if the vehicle descends too fast?  If you feel confident in your ability to proceed, then make sure you are in 4L and proceed with caution.  Allow engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: Do not descend a steep grade in NEUTRAL.  Use vehicle brakes in conjunction with engine braking.  Descending a grade too fast could cause you to lose control and be seriously injured or killed.  Off-Road Driving Tips  Driving Up Hill Once you have determined your ability to proceed and have shifted into the", "Tips  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle", "vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.", "In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance", "abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.", "API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c.20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause a", "authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue,", "or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov .", "Carbon Monoxide Warnings WARNING: Carbon monoxide (CO) in exhaust gases is deadly.  Follow the precautions below to prevent carbon monoxide poisoning: Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when", "is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Exhaust gases can injure or kill.  They contain carbon monoxide (CO), which is colorless and odorless.  Breathing it can make you unconscious and can eventually poison you.  To avoid breathing (CO), follow these safety tips: Carbon monoxide (CO) in exhaust gases is deadly.  Follow the precautions below to prevent carbon monoxide poisoning: Exhaust gases can injure or kill.  They contain carbon monoxide (CO), which is colorless and odorless.  Breathing it can make you unconscious and can eventually poison you.  To avoid breathing CO see A hot exhaust system can start a fire if you park over materials that can burn, such as grass or leaves, and those items that come into contact with your exhaust system.  Do not park or operate your vehicle in areas where", "come into contact with your exhaust system.  Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.  For further information For further information For further information The VIN is found on the left front corner of the A-pillar, visible from outside of the vehicle through the windshield.  Android\u2122 is a trademark of Google Inc. es posible que este equipo o dispositivo no cause interferencia perjudicial y este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operaci\u00f3n no deseada.  Exhaust Gas The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.  Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have an authorized dealer inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or", "inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.  Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.  In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change.  Replace as required.  WARNING: Exhaust gases can injure or kill.  They contain carbon monoxide (CO), which is colorless and odorless.  Breathing it can make you unconscious and can eventually poison you.  To avoid breathing (CO), follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.  If you are required to drive with the trunk/liftgate/rear doors open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed.  DO NOT use the recirculation mode.  If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling", "it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle.  Set the blower at high speed.  Carbon Monoxide Warnings WARNING: Carbon monoxide (CO) in exhaust gases is deadly.  Follow the precautions below to prevent carbon monoxide poisoning: Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Charge Air Cooler \u2014 Inter-Cooler (Diesel", "Until repaired, drive with all side windows fully open.  Charge Air Cooler \u2014 Inter-Cooler (Diesel Engine) The charge air cooler is positioned in front of the radiator and the air conditioner condenser.  Air enters the engine through the air cleaner and passes through the turbocharger, where it is pressurized.  This pressurized air rapidly reaches high temperature.  The air is then directed through a hose to the charge air cooler and through another hose to the intake manifold of the engine.  This cooling process enables more efficient burning of fuel resulting in fewer emissions.  To guarantee optimum performance of the system, keep the surfaces of the charge air cooler, condenser and radiator clean and free of debris.  Periodically check the hoses leading to and from the charge air cooler for cracks or loose clamps resulting in loss of pressure and reduced engine performance.", "Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example,", "prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command", "on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by", "the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.", "Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button,", "volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold", "which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Natural Speech Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Natural speech allows the user to speak commands in phrases or complete sentences.  The system filters out certain non-word utterances and sounds such as", "or complete sentences.  The system filters out certain non-word utterances and sounds such as \u201cah\u201d and \u201ceh.\u201d The system handles fill-in words such as \u201cI would like to\u201d.  The system handles multiple inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you want to call?\u201d in the case where a phone call was requested but the specific name was not recognized.  The system utilizes continuous dialog.  When the system requires more information from the user, it will ask a question to which the user can respond without pushing the Voice Command button on the steering wheel.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c", "cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  UCONNECT VOICE RECOGNITION Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of", "\u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.", "Off-Road Driving Tips  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled", "you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface", "should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?", "Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the", "maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster", "the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited", "the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle", "avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an", "injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of", "use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.", "Shifting Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Shifting Out of N (Neutral) Use the following procedure to prepare your vehicle for normal usage.  Bring the vehicle to a complete stop, leaving it connected to the tow vehicle.  Firmly apply the parking brake.  Start the engine.  Press and hold the brake pedal.  Shift the transmission into NEUTRAL.  Turn the engine off.  Shift the transfer case lever to the desired position.  Note: when shifting the transfer case out of", "the transfer case lever to the desired position.  Note: when shifting the transfer case out of n (neutral), the engine should remain off to avoid gear clash.  Shift the automatic transmission into PARK, or place manual transmission in NEUTRAL.  Release the brake pedal.  Disconnect vehicle from the tow vehicle.  Start the engine.  Press and hold the brake pedal.  Release the parking brake.  Shift the transmission into gear, release the brake pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally.  NEUTRAL (N) Use this range when the vehicle is standing for prolonged periods with the engine running.  Apply the parking brake and shift the transmission into PARK if you must exit the vehicle.  WARNING: Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.  These are unsafe practices that limit your response to changing traffic or road conditions.  You might lose control of the vehicle and have a collision.  CAUTION: Towing the vehicle, coasting, or", "might lose control of the vehicle and have a collision.  CAUTION: Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle N (Neutral) Neutral \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicleWARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  Five-position transfer case \u2014 if equipped the transfer case provides five positions: 2h (two-wheel drive high range) 4h", "case \u2014 if equipped the transfer case provides five positions: 2h (two-wheel drive high range) 4h auto (four-wheel drive auto high range) 4h part time (four-wheel drive part time high range) n (neutral) 4l (four-wheel drive low range) for additional information on the appropriate use of each transfer case position, see the following information:.", "CRUISE CONTROL SYSTEMS \u2014 IF EQUIPPED Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system: Cruise Control will keep your vehicle at a constant preset speed.  Adaptive Cruise Control (ACC) will adjust the vehicle speed up to the preset speed to maintain a distance with the vehicle ahead.  Note: In vehicles equipped with ACC, if ACC is not enabled, Fixed Speed Cruise Control will not detect vehicles directly ahead of you.  Always be aware of the feature selected.  Only one Cruise Control feature can operate at a time.  For example, if Fixed Speed Cruise Control is enabled, Adaptive Cruise Control will be unavailable, and vice versa.  Cruise Control When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  The Cruise Control buttons are located on the right side of the steering wheel.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too", "can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Using Cruise Control On Hills The transmission may downshift on hills to maintain the vehicle set speed.  The Cruise Control system maintains speed up and down hills.  A slight speed change on moderate hills is normal.  On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Cruise Control.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Cruise Control When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20", "When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  The Cruise Control buttons are located on the right side of the steering wheel.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control", "However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.", "See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a", "See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the", "Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can", "lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  To Reset The Manual Park Release: Pull upward on the tether strap, releasing it from the \u201clocked\u201d position.  Lower the Manual Park Release lever downward into its original position.  Original tether position tuck the tether strap into the base of the", "into its original position.  Original tether position tuck the tether strap into the base of the console, and reinstall the cover.  Extended Park Starting Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Note: Extended Park condition occurs when the vehicle has not been started or driven for at least 30 days.  CAUTION: To prevent damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.", "Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.", "the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by", "operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant", "for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service \"\u21e8if your", "reading does not return to normal, turn the engine off immediately and call for service \"\u21e8if your engine overheats\" .  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control", "help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential", "and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.", "safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service", "Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet", "clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.  Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for", "front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Rear Carpet Remove the grommets under the front seat (one left and one right).  Carpet split then pull the carpet out, to the rear and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin (if equipped), by removing the four bolts that hold it to the floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and", "floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then lift the assembly out from under the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear retainers remove carpet from the vehicle.  When reinstalling the carpet, perform these steps in reverse order making sure that the carpet is tucked under the scuffs, B-pillar, console, and then refasten the grommets.  Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket", "Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS", "or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress", "the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.", "OFF-ROAD PAGES \u2014 IF EQUIPPED If your vehicle is equipped with Off-Road Pages, it will provide you vehicle status while operating on off-road conditions.  It supplies information relating to the vehicle ride height, the status of the transfer case, the pitch and roll of the vehicle.  To access Off-Road Pages, press the Apps button on the touchscreen, and then select Off-Road Pages.  OFF-ROAD PAGES \u2014 IF EQUIPPED If your vehicle is equipped with Off-Road Pages, it will provide you vehicle status while operating on off-road conditions.  It supplies information relating to the vehicle ride height, the status of the transfer case, the pitch and roll of the vehicle.  To access Off-Road Pages, press the Apps button on the touchscreen, and then select Off-Road Pages.  Off-Road Pages Status Bar The Off-Road Pages Status Bar is located along the bottom of Off-Road Pages and is present in each of the selectable page options.  It provides information for the following items: transfer case status latitude/longitude", "options.  It provides information for the following items: transfer case status latitude/longitude altitude of the vehicle status of selec-speed control and selected speed in mph (km/h).  Off-Road Driving Tips", "In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  EMISSIONS INSPECTION", "diesel emissions standards required by the Environmental Protection Agency.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or", "ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently", "is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button", "and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an", "Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a", "to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate", "OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.", "Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates", "and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs", "needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android", "the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect", "the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and", "with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122", "Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on", "Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone", "the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.", "operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the", "apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Android Auto\u2122 allows you to access and stream your favorite music with apps like YouTube Music, iHeartRadio, and Spotify.  Using your smartphone\u2019s data plan, you can stream endless music on the road.", "Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.  SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of", "on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is", "the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke", "and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s", "equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  ASSIST AND SOS SYSTEM \u2014 IF EQUIPPED If equipped, the overhead console contains an ASSIST and an SOS button.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may", "to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  Off Road+ Display \u2014 If Equipped When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: 2h: off road+ unavailable, shift to 4wd 4h: 4wd high off road+ active 4l: 4wd low off road+ active adaptive cruise control (acc) and cruise control are not available when using off road+.  If either", "adaptive cruise control (acc) and cruise control are not available when using off road+.  If either option is selected, a dedicated message will display indicating that the features are not usable concurrently.  Messages are as follows: 4h: cruise control \u2014 cruise control unavailable in off road+ 4h: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in off road+ 4l: cruise control \u2014 cruise control unavailable in 4wd low 4l: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in 4wd low note: the behavior of electronic stability control while in off road+ varies depending on the 4wd status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also, holding the ESC OFF button for five seconds will turn off ESC.  In 4WD Low, Electronic Stability Control automatically shuts off regardless of the Off Road Status.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or", "SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  Press the settings button on the touchscreen.  Press the paired phones or audio sources button.  Press to select the particular phone or the particular audio device.  A pop-up menu will appear; press \u201cConnect Phone\u201d.  Press the X to exit out of the Settings screen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The MAX A/C button is only available on", "you to toggle up or down through the available settings.  The MAX A/C button is only available on the touchscreen.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsThe SYNC button is only available on the touchscreen.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of", "to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Press the Phone button.  Press the Dial/Keypad button on the touchscreen.  The Touch-Tone screen will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press \u201cDial/Call\u201d.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or", "press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the", "To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.", "will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.", "The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  Bed Rail Tie Down Locations Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.  The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction", "between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Supplemental Seat-Mounted Side Air Bags (SABs) are located in the outboard side of the front seats.  The SABs are marked with a \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d on a label or on the seat trim on the outboard side of the seats.  Four auxiliary switches are located in the lower switch bank of the instrument panel and can be used to power various electrical devices.  1 \u2014 Retainers 2 \u2014 Fuel Filter Protective Cover The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer", "through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your", "Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front", "rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  Lower Anchors And Tethers For CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some", "are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.", "It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have", "speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system:  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of", "Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Apple CarPlay\u00ae.  Anywhere using your mobile device and Vehicle Branded App From your computer on the Owner\u2019s Site (not available on all functions) Contacting SiriusXM Guardian\u2122 Customer Care (not available on all functions) Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.", "function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.  Apps The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  Apps The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a", "auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use", "your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may", "depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Description SmartWatch Integration puts the Vehicle Branded App right on your Apple\u00ae Watch or Android\u2122 Wear.  To get started, follow these steps: Download the Vehicle Branded App from the App Store\u00ae or Google Play.  Log onto the app from your smartphone using the username and password you created when you first set up your account.  Make sure your watch and smartphone are connected through Bluetooth\u00ae.  The Vehicle Branded App should appear on your SmartWatch.  Once the app is downloaded on your SmartWatch, you can enjoy these features: Lock or unlock your vehicle by tapping the remote lock button in the app and entering your security PIN.  Remote start or stop your vehicle.  View important vehicle", "the app and entering your security PIN.  Remote start or stop your vehicle.  View important vehicle stats, such as fuel level, vehicle location, tire pressure warning, and more.", "Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather,", "a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To", "other controls could cause serious injury or death.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Weather control settings hot weather and vehicle interior is very hot set the mode control to (panel mode), (max a/c) on, and blower on high.  Roll down the windows for a minute to flush out the hot air.  Adjust the controls as needed to achieve comfort.  Warm weather turn (a/c) on and set the mode control to (panel mode).  Cool sunny operate in (bi-level mode).  Cool & humid conditions set the mode control to (mix mode) and turn on (a/c) to keep windows clear.  Cold weather set the mode control to (floor mode).  If windshield fogging starts to occur, move the control to (mix mode).  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system", "the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or", "Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "Charging The Speaker Before using the Jeep\u00ae wireless speaker for the first time, fully charge your Jeep\u00ae wireless speaker until the battery indicator light stays solid green.  The Jeep\u00ae wireless speaker in-vehicle dock is the most ideal way to fully charge the speaker with the ignition in ON/RUN or ACC.  The speaker can also be charged with a power adapter.  To charge the Jeep\u00ae wireless speaker with a power adapter, insert the power adapter into a wall outlet.  Next, plug the power adapter into the Jeep\u00ae wireless speaker charging port on the back of the speaker.  Note: Jeep\u00ae wireless speaker will not charge within vehicle dock while the ignition is fully off.  Note: Power adapter needed for the Jeep\u00ae wireless speaker has to have a range of 14 VDC to 16.5 VDC, with a minimum of 2.7A and a barrel connector dimension of 5.5 mm by 2.5 mm.  Power adapter is not included.  Phone & Bluetooth\u00ae Pairing A feature of the Jeep\u00ae wireless speaker is the ability for the Jeep\u00ae wireless speaker to connect to devices using", "Jeep\u00ae wireless speaker is the ability for the Jeep\u00ae wireless speaker to connect to devices using Bluetooth\u00ae.  Follow these simple steps to connect a Bluetooth\u00ae-enabled device to the Jeep\u00ae wireless speaker: Press and hold the power button for 2-3 seconds to turn the Jeep\u00ae wireless speaker on.  Turn \u201con\u201d Bluetooth\u00ae for the device you desire to be connected to the Jeep\u00ae wireless speaker.  For instructions on how to turn on and off Bluetooth\u00ae settings for the desired device, refer to the device\u2019s user manual.  When powered on, the Jeep\u00ae wireless speaker will automatically enter pairing mode.  To pair a second device, press and hold the Bluetooth\u00ae button for 2-3 seconds, until an audio cue is heard.  Then go to the devices\u2019 Bluetooth\u00ae settings and select \u201cJeep\u00ae Speaker\u201d from the list.  The Jeep\u00ae wireless speaker will remember the last eight devices it has paired with.  Note: If the Jeep\u00ae wireless speaker is left on with an inactive Bluetooth\u00ae connection for 30 minutes, it will automatically turn off.  The Jeep\u00ae", "with an inactive Bluetooth\u00ae connection for 30 minutes, it will automatically turn off.  The Jeep\u00ae wireless speaker can be turned on again by pressing and holding the power button for 2-3 seconds.  The Jeep\u00ae wireless speaker is located behind the right rear passenger seat.  In order to access the Jeep\u00ae wireless speaker, the seat will need to be folded down or tilted forward.  A feature of the Jeep\u00ae wireless speaker is the ability for the Jeep\u00ae wireless speaker to connect to devices using Bluetooth\u00ae.  Follow these simple steps to connect a Bluetooth\u00ae-enabled device to the Jeep\u00ae wireless speaker: To remove the Jeep\u00ae wireless speaker, pull on the strap located on top of the mount for the speaker.  When the strap is pulled, the Jeep\u00ae wireless speaker can easily be lifted from the mount.", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action", "function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when", "the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the", "pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.", "Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.", "the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by", "operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant", "for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Instrument cluster descriptions tachometer indicates the engine speed in revolutions per minute (rpm x 1000).  Caution: do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature gauge the temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others", "of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Caution: driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument cluster display the instrument cluster display features a driver interactive display.  Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer indicates vehicle speed.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to", "indicates vehicle speed.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement", "to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Accessory Gauge The Accessory Gauge page displays the current status of the vehicle\u2019s Coolant Temperature, Oil Temperature, Oil Pressure, Transmission Temperature, and", "of the vehicle\u2019s Coolant Temperature, Oil Temperature, Oil Pressure, Transmission Temperature, and Battery Voltage.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper", "up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle", "to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized", "range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.", "Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all", "system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a", "testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you", "ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the", "going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the", "engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m", "This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  Jacking and tire changing jacking and tire", "by jacking on locations other than those indicated.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  If you get hung up or high-centered on an object, get out of", "only.  Avoid ice or slippery areas.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or", "vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar", "axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press", "Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the", "km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that", "while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to", "Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.", "SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey", "through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS", "in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s", "into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call,", "You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button", "centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.", "Driver Assist \u2014 If Equipped The Driver Assist menu displays the status of the ACC system.  Push and release the up or down arrow button until the driver assist menu is displayed in the instrument cluster display.  The Driver Assist menu displays the status of the ACC system.  Push and release the up or down arrow button until the driver assist menu is displayed in the instrument cluster display.  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Depending on the", "the available options related to that feature will then display on the screen.  Depending on the vehicle\u2019s options, feature settings may vary.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please", "dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d With SiriusXM Guardian\u2122, your vehicle has onboard assistance features located on the rearview mirror or overhead console designed to enhance your driving experience if you should ever need assistance or support.  Favorite Menus Speedometer Vehicle Info Off Road \u2014 If Equipped (show/hide) Driver Assist \u2014 If Equipped (show/hide) Fuel Economy (show/hide) Trip Info (show/hide) Stop / Start \u2014 If Equipped Audio (show/hide) Messages Screen Setup Vehicle Settings \u2014 If Equipped What is the phone number for roadside assistance call?  The phone number is: US: 1-800-521-2779 Canada: 1-800-363-4869 If I am subscribed to SiriusXM Guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance?  No, however your new vehicle may include Roadside Assistance Call services.  SAFETY FEATURES When the Safety/Driving Assistance button is selected on the touchscreen, the system displays", "When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Note: depending on the vehicle\u2019s options, feature settings may vary.  OCCUPANT RESTRAINT SYSTEMS Some of the most important safety features in your vehicle are the restraint systems:", "With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, see These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.  Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any", "you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be", "climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has", "the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze", "park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish", "this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.", "The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  Rear Cross Path Detection (RCP) is not a backup aid system.  It is intended to be used to help a driver detect an oncoming vehicle in a parking lot situation.  Drivers must be careful when backing up, even when using RCP.  Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up.  Failure to do so can result in serious injury or death.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a", "button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Different colored zones indicate the distance to the rear of the vehicle.  The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE", "Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.", "the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the", "other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.", "Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently", "ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  VEHICLE MODIFICATIONS/ALTERATIONS WARNING: Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in", "methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator", "cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of", "and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.", "For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  See Engine Fluids and Lubricants for the correct engine oil viscositySynthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Lubricant should be approximately 1/8 inch (3 mm) below the bottom edge of the oil fill hole.  Use only the manufacturer\u2019s recommended fluid Trac-Lok is especially helpful during slippery driving conditions.  With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction.  Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure", "may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure build-up or your tire pressure will be too low.  1 \u2014 Coolant Temperature 2 \u2014 Oil Temperature 3 \u2014 Battery Voltage 4 \u2014 Transmission Temperature 5 \u2014 Oil Pressure Operation in ambient temperature below 32\u00b0F (0\u00b0C) may require special considerations.  The following charts suggest these options:  Use only the manufacturer\u2019s recommended fluid For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will", "should be consistent with anticipated climate conditions under which vehicle operations will occur.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as", "illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).", "Outside Air Intake Make sure the air intake, located directly in front of the windshield, is free of obstructions, such as leaves.  Leaves collected in the air intake may reduce airflow, and if they enter the air distribution box, they could plug the water drains.  In Winter months, make sure the air intake is clear of ice, slush, and snow.  Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather.  To clear the windows, select Defrost or Mix mode and increase the front blower speed.  Do not use the Recirculation mode without A/C for long periods, as fogging may occur.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat,", "the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the", "a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.", "your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil", "to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no", "completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator", "within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To", "this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will", "(805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on", "system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak", "a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by", "or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.  Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a", "indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below", "Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily", "is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the", "is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly", "on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions,", "and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible", "and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.", "Apps The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android", "radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122", "the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Description SmartWatch Integration puts the Vehicle Branded App right on your Apple\u00ae Watch or Android\u2122 Wear.  To get started, follow these steps: Download the Vehicle Branded App from the App Store\u00ae or Google Play.  Log onto the app from your smartphone using the username and password you created when you first", "Log onto the app from your smartphone using the username and password you created when you first set up your account.  Make sure your watch and smartphone are connected through Bluetooth\u00ae.  The Vehicle Branded App should appear on your SmartWatch.  Once the app is downloaded on your SmartWatch, you can enjoy these features: Lock or unlock your vehicle by tapping the remote lock button in the app and entering your security PIN.  Remote start or stop your vehicle.  View important vehicle stats, such as fuel level, vehicle location, tire pressure warning, and more.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon", "of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .  Android", "plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc. Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .", "Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.  When TSC is functioning, the ESC Activation/Malfunction Indicator Light will flash, the engine power may be reduced, and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying.  TSC is disabled when the ESC system is in the \u201cPartial Off\u201d or \u201cFull Off\u201d modes.  Note: TSC cannot stop all trailers from swaying.  Always use caution when towing a trailer and follow the trailer tongue weight recommendations.  See \"\u21e8trailer towing\" for further information.  WARNING: If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway.  Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction", "between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as", "To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.", "brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the", "to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second", "to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Drag & Drop Menu Bar The Uconnect features and services in the main menu bar are easily customized for your preference.  Simply follow these steps: press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Note: This feature is only available if the vehicle is in PARK.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete,", "appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of", "right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.", "For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government", "ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction", "traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.  Temperature Grades The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the", "Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.  Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.  Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C.These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.", "Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system:  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC)", "traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACCThis indicator light will illuminate when the cruise control is set to the desired speed  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information", "in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.", "The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Automatic Dimming Mirror The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Automatic Dimming Mirror \u2014 If Equipped The rearview mirror can", "defrost outlets and demist outlets.  Automatic Dimming Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  This mirror automatically adjusts for headlight glare from vehicles behind you.  The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Note: The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.", "Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the", "form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited", "This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system", "of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use", "or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling,", "to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see \"\u21e8draining fuel/water separator filter \u2014 diesel engine\" .", "When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not", "order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  The Remote Door Lock/Unlock feature provides you the ability to lock or unlock the door on your vehicle without the keys and from virtually any distance.  All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on", "engaged (locked).  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your", "systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide", "center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.", "Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change", "The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is", "cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is", "generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil", "oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change", "SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An", "cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d", "tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "Oil Temperature Warning Light This warning light will illuminate to indicate the engine oil temperature is high.  If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.  Wait for oil temperature to return to normal levels.  This warning light will illuminate to indicate the engine oil temperature is high.  If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.  Wait for oil temperature to return to normal levels.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the", "dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  If the Low Oil Pressure Warning Light turns on while driving, stop the vehicle and shut down the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the lamp.  If the lamp is still illuminated, shut the engine off, contact an authorized dealer, and do not operate the vehicle until the cause is corrected.  If the lamp is no longer illuminated, the engine can be operated, but should be taken to an authorized dealer as soon as possible for further inspection.  This warning light will illuminate to warn of a high transmission fluid temperature.  This may occur with strenuous usage such as trailer towing.  If this light turns on, stop the vehicle and run the engine at idle or slightly faster, with the transmission in PARK (P) or", "the vehicle and run the engine at idle or slightly faster, with the transmission in PARK (P) or NEUTRAL (N), until the light turns off.  Once the light turns off, you may continue to drive normally.  If Manual transmission equipped, this warning will illuminate to warn of high clutch temperature.  This may occur with driver misuse of clutch pedal or resting foot on the clutch pedal or partially engaging the clutch for longer duration.  If the light turns on, it will be with an additional CLUTCH HOT message.  Stop the vehicle safely and run the engine at idle with transmission gear in NEUTRAL (N) until the light turns off.  Once the light turns off, follow the message displayed in the instrument cluster.  Oil Temperature Warning Light This warning light will illuminate to indicate the engine oil temperature is high.  If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.  Wait for oil temperature to return to normal levels.  Oil Pressure Warning Light This warning", "Wait for oil temperature to return to normal levels.  Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  Do Not Operate The Engine With Low Oil Pressure If the Low Oil Pressure Warning Light turns on while", "Not Operate The Engine With Low Oil Pressure If the Low Oil Pressure Warning Light turns on while driving, stop the vehicle and shut down the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the lamp.  If the lamp is still illuminated, shut the engine off, contact an authorized dealer, and do not operate the vehicle until the cause is corrected.  If the lamp is no longer illuminated, the engine can be operated, but should be taken to an authorized dealer as soon as possible for further inspection.  Note: Do not operate the vehicle until the cause is corrected.  This light does not show how much oil is in the engine.  The engine oil level must be checked under the hood.  CAUTION: If oil pressure falls to less than normal readings, shut the engine off immediately.  Failure to do so could result in immediate and severe engine damage.", "To Arm The System Follow these steps to arm the Vehicle Security system: Make sure the vehicle\u2019s ignition is placed in the OFF position.  Perform one of the following methods to lock the vehicle: push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zonePush the lock button on the key fob.  If any doors are open, close them.  Note: The Vehicle Security system will not arm if you lock the doors using the manual door lock.  To Arm The System Follow these steps to arm the Vehicle Security system: Make sure the vehicle\u2019s ignition is placed in the OFF position.  Perform one of the following methods to lock the vehicle: push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone Push the", "Passive Entry door handle with a valid key fob available in the same exterior zone Push the lock button on the key fob.  If any doors are open, close them.  Note: The Vehicle Security system will not arm if you lock the doors using the manual door lock.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic,", "disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two", "but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle", "door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped", "power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.", "Shifting Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Automatic Transmission \u2014 If Equipped  Transmission function is monitored electronically for abnormal conditions.  If a condition is detected that could result in transmission damage, Transmission Limp Home mode is activated.  In this mode, the transmission may operate only in certain gears, or may not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some situations, the", "Vehicle performance may be severely degraded and the engine may stall.  In some situations, the transmission may not re-engage if the engine is turned off and restarted.  The Malfunction Indicator Light (MIL) may be illuminated.  A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary.  It is important to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only manufacturer's specified transmission fluid It is important to maintain the transmission fluid at the correct level using the recommended fluid.  Using a transmission fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or", "failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  Using a lower gear while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  This action will also provide better engine braking.  Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing a heavy trailer), use the AutoStick shift control to select a lower gear Under these conditions, using a lower gear will improve performance and extend transmission", "gear Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  During cold weather, you may experience increased effort in shifting until the transmission fluid warms up.  This", "you may experience increased effort in shifting until the transmission fluid warms up.  This is normal.  Routine fluid and filter changes are not required.  However, change the fluid and filter if the fluid becomes contaminated (with water, etc.  ), or if the transmission is disassembled for any reason.", "The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force", "equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of", "maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure", "situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose", "are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting", "may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of", "in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  The ABS is designed to function with the Original Equipment Manufacturer (OEM) tires.  Modification may result in degraded ABS performance.  Your vehicle is equipped with an advanced Electronic Brake Control (EBC) system.  This system includes Anti-Lock Brake System (ABS), Brake Assist System (BAS), Electronic Brake Force Distribution (EBD), Electronic Roll Mitigation (ERM), Electronic Stability Control (ESC), Hill Start Assist (HSA), and Traction Control System (TCS).  These systems work together to enhance both vehicle stability and control in various driving conditions.  Anti-Lock Brake System (ABS) The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.", "cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the abs activates: abs motor noise or clicking sounds (you may continue to hear for a short time after the stop) brake pedal pulsations a slight drop of the brake pedal at the end of the stop note: the abs is designed to function with the original equipment manufacturer (oem) tires.  Modification may result in degraded ABS performance.  WARNING: The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting", "may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of", "in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.", "TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles", "a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension", "may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled", "using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension", "may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Recreational Towing \u2014 Four-Wheel Drive Models Note: The transfer case must be shifted into N (Neutral), automatic transmission must be in PARK, and manual transmission must be in gear (NOT in NEUTRAL) for recreational towing.  CAUTION: DO NOT dolly tow any 4WD vehicle.  Towing with only one set of wheels on the ground (front or rear) will cause severe transmission and/or transfer case damage.  Tow with all four wheels either ON the ground, or OFF the ground (using a vehicle trailer).  Tow only in the forward direction.  Towing this vehicle backwards can cause severe damage to the transfer case.  Automatic transmissions must be placed in PARK for recreational towing.  Manual transmissions must be placed in gear (not in Neutral) for recreational towing.  Before recreational towing, perform the procedure outlined under \u201cShifting Into N", "towing.  Before recreational towing, perform the procedure outlined under \u201cShifting Into N (Neutral)\u201d to be certain that the transfer case is fully in N (Neutral).  Otherwise, internal damage will result.  Towing this vehicle in violation of the previously listed requirements can cause severe transmission and/or transfer case damage.  Damage from improper towing is not covered under the New Vehicle Limited Warranty.  Do not use a bumper-mounted clamp-on tow bar on your vehicle.  The bumper face bar will be damaged.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If", "if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.", "may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or", "will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the", "when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the", "with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It", "a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel", "is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d,", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.", "Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201dWARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING:", "Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may", "safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle", "unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for", "switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid", "for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.  If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  To close the tailgate, lift upward until both sides latch into place.", "Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.  OCCUPANT RESTRAINT SYSTEMS Some of the most important safety features in your vehicle are the restraint systems:  SAFETY FEATURES When the Safety/Driving Assistance button is", "vehicle are the restraint systems:  SAFETY FEATURES When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Note: depending on the vehicle\u2019s options, feature settings may vary.  OCCUPANT RESTRAINT SYSTEMS Some of the most important safety features in your vehicle are the restraint systems:", "Automatic SOS \u2014 If Equipped Automatic SOS is a hands-free safety service that can immediately connect you with help in the event that your vehicle\u2019s airbags deploy.  Please refer to your provided radio supplement for complete information.  SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant", "the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice", "with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An", "and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.", "when you need it.  You could be injured if the air bag system is not there to help protect you.  Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.", "Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.  SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of", "on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is", "the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke", "and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s", "equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  Sos call system limitations vehicles sold in mexico do not have sos call system capabilities.  SOS or other emergency line operators in Mexico may not answer or respond to SOS system calls.  If the SOS Call system detects a malfunction, any of the following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires", "be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d an in-vehicle audio message will state \u201cvehicle device requires service.  Please contact an authorized dealer.\u201d even if the sos call system is fully functional, factors beyond fca us llc\u2019s control may prevent or stop the sos call system operation.  These include, but are not limited to, the following factors: the ignition is in the off position the vehicle\u2019s electrical systems are not intact the sos call system software and/or hardware are damaged during a crash the vehicle battery loses power or becomes disconnected during a vehicle crash lte (voice/data) or 4g (data) network and/or global positioning satellite signals are unavailable or obstructed equipment malfunction at the sos operator facility operator error by the sos operator lte (voice/data) or 4g (data) network congestion weather buildings, structures, geographic terrain, or tunnels warning: ignoring the", "congestion weather buildings, structures, geographic terrain, or tunnels warning: ignoring the rearview mirror light could mean you will not have sos call services.  If the Rearview Mirror light is illuminated, have an authorized dealer service the SOS Call system immediately.  The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.  If the Air Bag Warning Light is illuminated, have an authorized dealer service the Occupant Restraint Control system immediately.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the", "serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber.  Never place anything on or near the vehicle\u2019s LTE (voice/data) or 4G (data) and GPS antennas.  You could prevent LTE (voice/data) or 4G (data) and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable LTE (voice/data) or 4G (data) network connection and a GPS signal is required for the SOS Call system to function properly.  Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.", "Adding Diesel Exhaust Fluid The DEF gauge (located on the instrument cluster display) will display the level of DEF remaining in the tankNote: Driving conditions (altitude, vehicle speed, load, etc.)  will affect the amount of DEF that is used in your vehicle.  System Overview This vehicle is equipped with a Diesel Exhaust Fluid (DEF) injection system and a Selective Catalytic Reduction (SCR) catalyst to meet the emission requirements.  The def injection system consists of the following components: def tank def pump def injector electronically-heated def lines nox sensors temperature sensors scr catalyst the def injection system and scr catalyst enable the achievement of diesel emissions requirements; while maintaining outstanding fuel economy, drivability, torque and power ratings.  For system messages and warnings see Note: Your vehicle is equipped with a DEF injection system.  You may occasionally hear an audible clicking noise from under the vehicle at a stop.  This is normal operation.  The DEF pump", "audible clicking noise from under the vehicle at a stop.  This is normal operation.  The DEF pump will run for a period of time after engine shutdown to purge the DEF system.  This is normal operation and may be audible from the rear of the vehicle.  DEF tank DEF pump DEF injector Electronically-heated DEF Lines NOx sensors Temperature sensors SCR catalyst DEF is subject to freezing at the lowest temperatures.  For example, DEF may freeze at temperatures at or below 12\u00b0F (-11\u00b0C).  The system has been designed to operate in this environment.  Any containers or parts that come into contact with DEF must be DEF compatible (plastic or stainless steel).  Copper, brass, aluminum, iron or non-stainless steel should be avoided as they are subject to corrosion by DEF.  If DEF is spilled, it should be wiped up completely.  The DEF gauge (located on the instrument cluster display) will display the level of DEF remaining in the tank", "Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio.  This condition may be lessened or eliminated by repositioning the mobile phone within the vehicle.  This condition is not harmful to the radio.  If your radio performance does not satisfactorily improve from repositioning the mobile phone, it is recommended that the volume be turned down or off during mobile phone operation when not using the Uconnect system.  Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors.  Installing some form of aftermarket window tinting that affects radio wave signals.  Lots of snow or ice around the wheels or wheel housings.  Using tire chains on the vehicle.  Using wheels/tires not equipped with TPMS sensors.  The radio unit is acting as the amplifier for audio output from the Auxiliary device.  Therefore, if the volume control on the Auxiliary device is set too low, there will be", "device.  Therefore, if the volume control on the Auxiliary device is set too low, there will be insufficient audio signal for the radio unit to play the music on the device.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn", "on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.  After going off-road, it is always a good idea to check for damage.  That way you can get any problems taken care of right away and have", "good idea to check for damage.  That way you can get any problems taken care of right away and have your vehicle ready when you need it.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and", "Note: inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Warning: abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  WARNING: If the gross trailer weight is 2,000 lb (907 kg) or more, it is recommended to use a weight-distributing hitch to ensure stable handling of your vehicle.  If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.  The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.  The entire weight of the trailer must be supported by the scale.  The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW", "temporary) loaded in or on the trailer in its \"loaded and ready for operation\" condition.  GVWR GTW GAWR Tongue weight rating for the trailer hitch utilized Position the truck to be ready to connect to the trailer (do not connect the trailer).  Measure the height from the top of the front fender to ground, this is height H1.  Measuring Height (H) Attach the trailer to the vehicle without the weight distribution bars connected.  Measure the height from the top of the front fender to ground, this is height H2.  Install and adjust the tension in the weight distributing bars per the manufacturer\u2019s recommendations so that the height of the front fender is approximately H1 (H2=H1).  The truck can now be driven.  Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.  Trailer And Tongue Weight Never exceed the maximum tongue weight stamped on your bumper or trailer hitch.  Consider the following items when computing the weight on the", "on your bumper or trailer hitch.  Consider the following items when computing the weight on the rear axle of the vehicle: the tongue weight of the trailer the weight of any other type of cargo or equipment put in or on your vehicle the weight of the driver and all passengers note: remember that everything put into or on the trailer adds to the load on your vehicle.  Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.  Refer to the Tire And Loading Information Placard for the maximum combined weight of occupants and cargo for your vehicle.  Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo.  The label also specifies maximum capacities of front and rear Gross Axle Weight Rating (GAWR).  Total load must be limited so GVWR on front and rear GAWR are not exceeded.", "If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.", "tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.  The ASSIST and SOS Call Buttons On Your Rearview Mirror Or Overhead Console If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a", "console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons  ASSIST Call The ASSIST button is used to automatically connect you to any one of the following support centers: Roadside Assistance \u2013 If you get a flat tire, or need a tow, just push the ASSIST button and you\u2019ll be connected to someone who can help.  Roadside Assistance will know what vehicle you\u2019re driving and its location.  Additional fees may apply for roadside assistance.  SiriusXM Guardian\u2122 Customer Care \u2013 In-vehicle support for SiriusXM Guardian\u2122.  Vehicle Customer Care \u2013 Total support for all other vehicle issues.  Uconnect Customer Care - Total support for Radio, Phone and NAV issues.", "For information on the Door Off Mirror Kit (if equipped) when the front doors are removed, see If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Door Off Mirror To install the Door Off Mirrors, proceed as follows:  Door Off Mirror Kit \u2014 If Equipped If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  To install the Door Off Mirrors, proceed as follows: Remove both front doorsRemove the cowl bolt closest to the door opening using a #40 Torx head driver, and store in a safe location.  Cowl bolt location push the mirror bracket forward onto the a-pillar, making sure to align the bottom of the bracket with the upper door hinge, and the hole from the removed cowl bolt.  Push bracket onto a-pillar place the bracket bushing behind the mirror bracket (over the cowl bolt hole), then insert the bracket", "the bracket bushing behind the mirror bracket (over the cowl bolt hole), then insert the bracket bolt into the mirror bracket, through the bracket bushing.  Attaching mirror bracket to the vehicle 1 \u2014 bracket bushing 2 \u2014 bracket bolt insert the hinge shoulder bolt through the bottom of the upper door hinge up into the mirror bracket, then rotate the bracket knob toward the rear of the vehicle to secure the mirror bracket to the a-pillar.  Attaching mirror bracket to the vehicle 1 \u2014 bracket knob 2 \u2014 hinge shoulder bolt tighten both the bracket bolt and the hinge shoulder bolt with a #40 torx head driver.  Recommended torque specification for the bracket bolt is 6 ft-lb (8 N\u00b7m), and 7.5 ft-lb (10 N\u00b7m) for the hinge shoulder bolt.  Lower the mirror assembly onto the mirror bracket.  Lower mirror assembly onto bracket insert the three mirror screws into the mirror assembly, and tighten into the mirror bracket using a #30 torx head driver.  Recommended torque specification for the mirror screws is 4 ft-lb (5.5", "a #30 torx head driver.  Recommended torque specification for the mirror screws is 4 ft-lb (5.5 N\u00b7m).  Mirror screw locations repeat the steps on the other side of the vehicle.  WARNING: All occupants must wear seat belts during off-road operation with doors removed.  For off-road driving tips, see Do not store detached doors inside of the vehicle, as they may fly around and cause personal injury or death in the event of a sudden stop, rough terrain, or a collision.  Note: If this kit is being installed with the optional lamp bracket, the bracket bushing from step 4 is not needed.  Use the spacer from the lamp bracket.  The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  If equipped with the Door Off Mirror Kit, exterior rearview mirrors can be installed on to the upper body door hinges after the front doors have been removed.  Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an", "Outside rearview mirrors are mounted on the doors.  If you choose to remove the doors, see an authorized dealer for a replacement cowl-mounted outside mirror.  Federal law requires outside mirrors on vehicles for on-road use.", "A/C Button Press and release this button on the touchscreen, or push the button on the faceplate to change the current setting.  The A/C indicator illuminates when A/C is ON.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  Note: If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system.  When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into", "the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service Press and release this button to turn the Climate Control ON/OFF.  When the Key Off Options/Engine Off Options button is pressed on the touchscreen, the system displays the options related to vehicle shutoff.  These settings will only activate when the ignition is set to OFF.  Depending on the vehicle\u2019s options, feature settings may vary.  Press and release this button on the touchscreen, or push and release the button on the blower knob to turn the Climate Control ON/OFF.  To Turn Off The Engine Using The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C", "The ENGINE START/STOP Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Push of the ESC OFF Button: Traction Control will turn off, but Stability Control will remain active.  Hold the ESC OFF Button for five seconds: Traction Control and Stability Control will turn off.  The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition is placed in the ON/RUN mode.  Each time the ignition is placed in the ON/RUN position, the ESC system will be on even if it was turned off previously.  The ESC system will make buzzing or clicking sounds when it is active.  This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner", "the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  A/C Button Push the A/C button to engage the Air Conditioning (A/C).  The A/C indicator illuminates when A/C is on.  Note: For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the", "seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.", "Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Extreme Cold Weather The cartridge block heater", "are available from an authorized Mopar\u00ae dealer.  Extreme Cold Weather The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  Note: The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.", "equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Power Outlets There is a 12 Volt (13 A) auxiliary power outlet that can provide power for accessories designed for use with the standard power outlet adapters.  The front power outlet is located in the center of the instrument panel below the climate controls, and is powered from the ignition switch.  Power is available when the ignition switch is in the ACC or ON/RUN position.  WARNING: To avoid serious injury or death: Do not insert any objects into the receptacles.  Do not touch with wet hands.  Close the lid when not in use.  If this outlet is mishandled, it may cause an electric shock and failure.  CAUTION: Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and", "plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of", "vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  The cartridge block heater clips into the engine block near the water jacket and transfers heat to the coolant.  It requires a 110\u2013115 Volt AC electrical outlet with a grounded, three-wire extension cord.  Its use is recommended for environments that routinely fall below -10\u00b0F (-23\u00b0C).  It should be used when the vehicle has not been running overnight or longer periods and should be plugged in two hours prior to start.  Its use is required for cold starts with temperatures under -20\u00b0F (-28\u00b0C).  To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available", "at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  The engine block heater and heater cord are factory installed options.  If your vehicle is not equipped, engine block heaters and heater cords are available from an authorized Mopar\u00ae dealer.  Do not exceed the maximum power of 160 W (13 A) at 12 Volts.  If the 160 W (13 A) power rating is exceeded, the fuse protecting the system will need to be replaced.  Power outlets are designed for accessory plugs only.  Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.  Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.  Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.).  Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine", "the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.  Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.  ), will degrade the battery even more quickly.  Only use these intermittently and with greater caution.  After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle's battery.  Power outlets are designed for accessory plugs only.  Do not hang any type of accessory or accessory bracket from the plug.  Improper use of the power outlet can cause damage Turn off the Fuel Filter Heater, Turn off the HVAC Blower Motor, Close the HVAC Circulation Door Cut off battery power to the: Engine Electric Motor (if equipped) Electric power steering Brake booster Electric park brake Automatic transmission gear selector Horn Front wiper", "Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry (If Equipped) The Passive Entry system is a feature that allows you to lock and unlock the vehicle\u2019s door(s) and tailgate without having to push the key fob lock or unlock buttons.  Note: Passive Entry may be programmed on/off through Uconnect Settings The key fob may not be detected by the vehicle Passive Entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may interfere with the key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.  Passive Entry Unlock initiates Headlight Illumination On Approach (low beams, license plate lamp, parking lights) for whichever duration is set within the Uconnect Settings between 0, 30, 60 or 90 seconds.  Passive Entry Unlock also initiates two flashes of the turn signal lights.  If wearing gloves, if it has been raining/snowing, or there is salt/dirt covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a", "covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.  The doors may unlock when water is sprayed on the Passive Entry door handles if the key fob is located outside of the vehicle within 5 ft (1.5 m) of the handle.  If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will relock and, if equipped, will arm the Vehicle Security system.  Keyless Enter \u2018n Go\u2122 \u2014 Passive Entry (If Equipped) The Passive Entry system is a feature that allows you to lock and unlock the vehicle\u2019s door(s) and tailgate without having to push the key fob lock or unlock buttons.  Note: Passive Entry may be programmed on/off through Uconnect Settings The key fob may not be detected by the vehicle Passive Entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may interfere with the key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.", "key fob\u2019s wireless signal and prevent the Passive Entry system from locking/unlocking the vehicle.  Passive Entry Unlock initiates Headlight Illumination On Approach (low beams, license plate lamp, parking lights) for whichever duration is set within the Uconnect Settings between 0, 30, 60 or 90 seconds.  Passive Entry Unlock also initiates two flashes of the turn signal lights.  If wearing gloves, if it has been raining/snowing, or there is salt/dirt covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.  The doors may unlock when water is sprayed on the Passive Entry door handles if the key fob is located outside of the vehicle within 5 ft (1.5 m) of the handle.  If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will relock and, if equipped, will arm the Vehicle Security system.  Frequency Operated Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive", "Button Integrated Key (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function only if the ignition switch is in the OFF position.  FOBIK-Safe only executes in vehicles with Passive Entry.  There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: A lock request is made by a valid Passive Entry key fob while a door is open.  A lock request is made by the Passive Entry door handle while a door is open.  A lock request is made by the door panel switch while the door is open.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  Note: The", "system, the key fob protection described in this section remains active/functional.  Note: The vehicle will only unlock the doors during a FOBIK-Safe operation when a valid Passive Entry key fob is detected inside the vehicle.  The vehicle will not unlock the doors when any of the following conditions are true: A second valid Passive Entry key fob is detected outside of the vehicle (within 5 ft (1.5 m) of a Passive Entry door handle).  The doors are manually locked using the door lock knobs.  Three attempts are made to lock the doors using the door panel switch, and then the doors are closed.  To Lock The Vehicle\u2019s Doors With one of the vehicle\u2019s Passive Entry key fobs within 5 ft (1.5 m) of the driver or passenger front door handles, pushing the Passive Entry lock button will lock the vehicle doors.  Note: When pushing the door handle lock button, DO NOT grab the door handle.  This could unlock the door(s).  Note: After pushing the door handle button, the driver must wait three seconds before locking or", "Note: After pushing the door handle button, the driver must wait three seconds before locking or unlocking the doors, using any Passive Entry door handle.  This is done to allow the driver to check if the vehicle is locked by pulling the door handle without the vehicle unlocking.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in \u201cPreventing Inadvertent Locking Of Passive Entry Key Fob In Vehicle\u201d remains active/functional.  The Passive Entry system will not operate if the key fob battery is depleted  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking", "system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.", "If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the", "parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  When the parking brake is applied and the automatic transmission is placed in gear, the Brake Warning Light will flash.  If vehicle speed is detected, a chime will sound to alert the driver.  Fully release the parking brake before attempting to move the vehicle.  This light only shows that the parking brake is applied.  It does not show the degree of brake application.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  When the parking brake is applied", "illuminate, have the light inspected by an authorized dealer.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  If the headlights or parking lights are left on after the ignition is placed in the OFF position, the vehicle will chime when the driver\u2019s door is opened.  Vehicle parking brake is applied Stability event occurs Gear selector is moved out of DRIVE Engine overspeed occurs Clutch pedal is pressed (manual transmission only) Vehicle is operating at a low RPM (manual transmission only) Always apply the parking brake.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  A delay of the start of up to five seconds is possible under very cold conditions.  The \u201cWait to Start\u201d telltale will be illuminated during the preheat process.  When the engine \u201cWait To Start\u201d telltale turns off the engine will automatically crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before", "crank.  If the Water in Fuel Indicator Light remains on, DO NOT START the engine before you drain the water from the fuel filters to avoid engine damage The system will automatically engage the starter to crank the engine.  If the vehicle fails to start, the starter will disengage automatically after 25 seconds.  If you wish to stop the cranking of the engine prior to the engine starting, push the ENGINE START/STOP button again.  Check that the Oil Pressure Warning Light has turned off.  release the parking brake  Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and", "Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.  This warning light will illuminate when the ignition is in the ON/RUN position before engine start.  If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will", "is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following:  Air Bag Warning Light The Air Bag Warning Light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in the ON/RUN position.  If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.  This light will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is removed.  If the light comes on intermittently or remains on while driving,", "on until the fault is removed.  If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately \"\u21e8air bag warning light\" .", "The power windows feature allows for movement of the windows with the push of a button.  The power window switches are located on the instrument panel below the climate controls.  Push the switch downward to open the window and pull upward to close the window.  The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  Power Window Switches Never leave children unattended in a vehicle, and do not let children play with power windows.  Do not leave the key fob in or near the vehicle, or in a location accessible to children.  Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.  Such entrapment may result in serious injury or death.  The power window switches will remain active for up to 10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel", "10 minutes after the ignition is placed in the OFF position.  Opening either front door will cancel this feature.  There are window switches located on the rear of the center console for the rear passenger windows.  Auto-Down Feature The driver door power window switch and the front passenger door power window switch have an Auto-Down feature.  Push the window switch down, past the detent, and release and the window will go down automatically.  To open the window part way, push the window switch down briefly, without going past the detent, and release it when you want the window to stop.  To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.  WARNING: There is no anti-pinch protection when the window is almost closed.  Be sure to clear all objects from the window before closing.  Power Door Locks \u2014 If Equipped The power door lock switch is located on each front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.", "front door panel.  Push the switch forward to unlock the doors, and rearward to lock the doors.  WARNING: For personal security reasons and safety in a collision, lock the vehicle doors when you drive, as well as when you park and exit the vehicle.  When exiting the vehicle, always place the ignition in the OFF position and remove the key from the vehicle.  Unsupervised use of vehicle equipment may cause severe personal injuries and death.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle or in a location accessible to children.  A child could operate power windows, other controls, or move the vehicle.", "Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable", "battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain", "could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump", "pack, follow the manufacturer's operating instructions and precautions.  Preparations For Jump Start The battery in your vehicle is located in the right rear of the engine compartment.  If your vehicle is equipped with a Stop/Start system, it will be equipped with two batteries See the following steps to prepare for jump starting: Apply the parking brake, shift the automatic transmission into PARK (P) (manual transmission in NEUTRAL) and place the ignition in OFF mode.  Turn off the heater, radio, and all electrical accessories.  If using another vehicle to jump start the battery, park the vehicle within the jumper cable\u2019s reach, apply the parking brake and make sure the ignition is OFF.  WARNING: Only use the positive battery post on the main battery to jump start your vehicle.  Serious injury or death could result if you attempt to jump start using the supplemental battery.  Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other", "explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting.  Note: the positive (+) battery post is covered with a protective cap.  Lift up on the cap to gain access to the post.  WARNING: Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.  Take care to avoid the radiator cooling fan whenever the hood is raised.  It can start anytime the ignition switch is ON.  You can be injured by moving fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an", "fan blades.  Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.  You could be seriously injured.  Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.  Keep open flames or sparks away from the battery.  Jump Starting Procedure WARNING: Failure to follow this jump starting procedure could result in personal injury or property damage due to battery explosion.  CAUTION: Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.  Note: Make sure at all times that unused ends of jumper cables are not contacting each other or either vehicle while making connections.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so", "or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.", "To Deactivate A soft tap on the brake pedal, pushing the CANC (cancel) button, or normal brake pressure while slowing the vehicle will deactivate the Cruise Control without erasing the set speed from memory.  The following conditions will also deactivate the cruise control without erasing the set speed from memory: vehicle parking brake is applied stability event occurs gear selector is moved out of drive engine overspeed occurs clutch pedal is pressed (manual transmission only) vehicle is operating at a low rpm (manual transmission only) pushing the on/off button or placing the ignition in the off position, erases the set speed from memory.  Adaptive Cruise Control Off When ACC is deactivated, the display will read \u201cAdaptive Cruise Control Off.\u201d To Deactivate A soft tap on the brake pedal, pushing the CANC (cancel) button, or normal brake pressure while slowing the vehicle will deactivate the Cruise Control without erasing the set speed from memory.  The following conditions will also deactivate the cruise", "erasing the set speed from memory.  The following conditions will also deactivate the cruise control without erasing the set speed from memory: vehicle parking brake is applied stability event occurs gear selector is moved out of drive engine overspeed occurs clutch pedal is pressed (manual transmission only) vehicle is operating at a low rpm (manual transmission only) pushing the on/off button or placing the ignition in the off position, erases the set speed from memory.  To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) on/off button.  The ACC menu in the instrument cluster display will read \u201cACC Ready.\u201d To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again.  At this time, the system will turn off and the instrument cluster display will read \u201cAdaptive Cruise Control (ACC) Off.\u201d WARNING: Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous.  You could accidentally set the system or cause it to go faster than you", "not in use is dangerous.  You could accidentally set the system or cause it to go faster than you want.  You could lose control and have a collision.  Always leave the system off when you are not using it.  When ACC is deactivated, the display will read \u201cAdaptive Cruise Control Off.\u201d The following conditions will also deactivate the Cruise Control without erasing the set speed from memory: When the condition that deactivated the system is no longer present, the system will return to the \u201cAdaptive Cruise Control Off\u201d state and will resume function by simply reactivating it.  A soft tap on the brake pedal, pushing the CANC (cancel) button, or normal brake pressure while slowing the vehicle will deactivate the Cruise Control without erasing the set speed from memory.  Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will", "and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.", "Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat buildup may cause serious injury or death.  It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.  In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.  Be sure everyone in your vehicle is in a seat and using a seat belt properly.  Protection From Atmospheric Agents Vehicle body care requirements vary according to geographic locations and usage.  Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.  Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and", "contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather, and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.  The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or", "Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Glove Compartment The glove compartment is located on the passenger side of the instrument panel.  To open the glove compartment, pull the release handle.  WARNING: Do not operate this vehicle with the glove compartment in the open position.  Driving with the glove compartment open may result in injury in a collision.  Starting Fluids The engine is equipped with a glow plug preheating system.  If the instructions in this manual are followed, the engine should start in all conditions and no type of", "instructions in this manual are followed, the engine should start in all conditions and no type of starting fluid should be used.  WARNING: Do not leave children or animals inside parked vehicles in hot weather.  Interior heat build-up may cause serious injury or death.  When leaving the vehicle, always make sure the keyless ignition node is in the OFF position, remove the key fob from the vehicle and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the gear selector.  Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter \u2018n Go\u2122 in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.", "If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around.  To do so may result in tipping and rolling the vehicle, which may result in severe injury.  Always back carefully straight down a hill in REVERSE.  Never back down a hill in NEUTRAL using only the vehicle brakes.  Never drive diagonally across a hill, always drive straight up or down.  Before driving down a steep hill, you need to determine if it is too steep for a safe descent.  What is the surface traction?  Is the grade too steep to maintain a slow, controlled descent?  Are there obstacles?  Is it a straight descent?  Is there plenty of distance at the base of the hill to regain control if the vehicle descends too fast?  If you feel confident in your ability to proceed, then make sure you are in 4L and proceed with caution.  Allow engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  Moving from a high gear down to a lower", "brakes, if necessary, but do not allow the tires to lock.  Moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills.  In addition, downshifting at the right time provides better acceleration when you desire to resume speed.  Downshift progressively.  Do not skip gears to avoid overspeeding the engine and clutch.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Downhill Before driving down a steep hill, you need to determine if it is too steep for a safe descent.  What is the surface", "a steep hill, you need to determine if it is too steep for a safe descent.  What is the surface traction?  Is the grade too steep to maintain a slow, controlled descent?  Are there obstacles?  Is it a straight descent?  Is there plenty of distance at the base of the hill to regain control if the vehicle descends too fast?  If you feel confident in your ability to proceed, then make sure you are in 4L and proceed with caution.  Allow engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: Do not descend a steep grade in NEUTRAL.  Use vehicle brakes in conjunction with engine braking.  Descending a grade too fast could cause you to lose control and be seriously injured or killed.  Off-Road Driving Tips  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the", "possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which", "or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.", "Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the", "the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.", "To Lock/Unlock The Doors And Tailgate Push and release the unlock button on the key fob once to unlock the driver\u2019s door, or twice to unlock all the doors.  To lock all the doors, push the lock button once.  When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated.  When the doors are locked, the turn signals will flash and the horn will chirp.  Note: All doors can be programmed to unlock on the first push of the unlock button through Uconnect Settings The mechanical flip key can be used to lock or unlock the doors, tailgate, glove compartment, storage compartments (if equipped), and rear seatbacks.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  When a door is", "system, the key fob protection described in this section remains active/functional.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless", "is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter \u2018n Go\u2122 (if equipped), and Remote Start (if equipped).  The key fob allows you to lock or unlock the doors and tailgate from distances up to approximately 66 ft (20 m).  The key fob does not need to be pointed at the vehicle to activate the system.  The key fob also contains a mechanical key.  When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks.  In order to ensure complete effectiveness of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is", "devices inside of the key fob, avoid exposing the key fob to direct sunlight.  Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.  Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.  Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  Key Fob The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.", "Autostop Mode The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  WARNING: Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument clusterVehicle speed must be less than 2 mph (3 km/h).  The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.", "The gear selector must be in the NEUTRAL position and the clutch pedal must be fully released.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The Autostop Mode, The Following Must Occur: The system must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument", "must be in STOP/START READY state.  A STOP/START READY message will be displayed in the instrument cluster display within the Stop/Start sectionThe vehicle must be completely stopped.  The gear selector must be in a forward gear and the brake pedal pressed.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  To Activate The Autostop Mode, The Following Must Occur: Conditions That Will Cause The Engine To Start Automatically While In Autostop Mode: To Activate The STOP/START AUTOSTOP ACTIVE Mode, The Following Must Occur: Conditions that will cause the engine to start automatically while in STOP/START AUTOSTOP ACTIVE mode, the engine will start automatically when: This indicator light will illuminate when the Stop/Start function is in \u201cAutostop\u201d mode.  The Stop/Start feature is enabled after every normal engine start.  It will", "is in \u201cAutostop\u201d mode.  The Stop/Start feature is enabled after every normal engine start.  It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h).  At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTOSTOP ACTIVE mode.  While in an Autostop, the Climate Control system may automatically adjust airflow to maintain cabin comfort.  Customer settings will be maintained upon return to an engine running condition.  The engine will shut down, the tachometer will move to the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop.  Customer settings will be maintained upon return to an engine-running condition.  The engine will shut down, the tachometer will fall to the stop/start position, the stop/start autostop active message will appear, and the heater/air conditioning (hvac) air flow will be reduced.  This light alerts the driver that the vehicle is in", "conditioning (hvac) air flow will be reduced.  This light alerts the driver that the vehicle is in the neutral mode", "To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To Set A Desired Speed Turn the Cruise Control on.  When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release.  Release the accelerator and the vehicle will operate at the selected speed.  Note: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button.  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when", "20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set", "ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.  Cruise Control SET Indicator Light \u2014 If Equipped With A Premium Instrument Cluster This indicator light will illuminate when the cruise control is set to the desired speed  To set a desired speed when the vehicle reaches the speed desired, push the set (+) button or the set (-) button and release.  The instrument cluster display will show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed", "show the set speed.  If acc is set when the vehicle speed is below 20 mph (32 km/h), the set speed will default to 20 mph (32 km/h).  If either system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle.  Note: Fixed Speed Cruise Control can be used without ACC enabled.  To change between the different modes, push the ACC on/off button which turns the ACC and the Fixed Speed Cruise Control off.  Pushing the Fixed Speed Cruise Control on/off button will result in turning on (changing to) Fixed Speed Cruise Control mode.  WARNING: In Fixed Speed Cruise Control mode (ACC not enabled), the system will not react to vehicles ahead.  In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected.  Be sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which", "sure to maintain a safe distance between your vehicle and the vehicle ahead.  Always be aware which mode is selected.  Note: Fixed Speed Cruise Control cannot be set below 20 mph (32 km/h).  Note: Keeping your foot on the accelerator pedal can cause the vehicle to continue to accelerate beyond the set speed.  If this occurs, the message \u201cDRIVER OVERRIDE\u201d will display in the instrument cluster display.  If you continue to accelerate beyond the set speed while ACC is enabled, the system will not be controlling the distance between your vehicle and the vehicle ahead.  The vehicle speed will only be determined by the position of the accelerator pedal.", "Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still", "This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote", "serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Warm up the engine before placing it under load.  Do not operate the engine at idle for prolonged periods.  Use the appropriate transmission gear to prevent engine lugging.  Observe vehicle oil pressure and temperature indicators.  Check the coolant and oil levels frequently.  Vary throttle position at highway speeds when carrying or towing significant weight.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full", "operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  After full load operation, idle the engine for a few minutes before shutting it down.  This idle period will allow the lubricating oil and coolant to carry excess heat away from the turbocharger.", "Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the", "start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: The message will stay active until the ignition is placed in the ON/RUN position.  Starting with the ignition in the OFF position.  Push the ENGINE START/STOP button once to place the ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP", "ignition to the ACC position (instrument cluster will display \u201cACC\u201d).  Push the ENGINE START/STOP button a second time to place the ignition to the RUN position (instrument cluster will display \u201cON/RUN\u201d).  Push the ENGINE START/STOP button a third time to return the ignition to the OFF position (instrument cluster will display \u201cOFF\u201d).  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  To insert an Auxiliary device, gently insert the Auxiliary device cable into the AUX port.  If you insert an Auxiliary device with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system", "with the ignition and the radio on, the unit will switch to AUX Mode and begin to play.  The system will automatically time out and the ignition will cycle to the OFF position after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine not running) position and the transmission is in PARK.  For Keyless Enter \u2018n Go\u2122 equipped vehicles, the engine will turn off and the ignition will change to ACC position.  After 30 minutes the ignition switches to OFF automatically, unless the driver turns the ignition OFF.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  The Power Inverter will only turn on if the ignition is in the ACC or ON/RUN position.  Due to built-in overload protection, the power inverter will turn off if the power rating is exceeded.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is", "which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on", "obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "Daytime Running Lights (DRLs) \u2014 If Equipped The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  Note: For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be", "Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  BeltAlert can be activated or deactivated by an authorized dealer.  FCA US LLC does not recommend deactivating BeltAlert.  The Daytime Running Lights (DRLs) are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are", "are in a dedicated position below the headlight assembly.  DRLs are active when the low beams are not on while the vehicle\u2019s transmission is in any position (automatic transmission), or when the vehicle begins to move (manual transmission).  Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent.  Headlights will be deactivated when the headlight switch is placed in the parking lights position.  However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights.  The DRLs may be deactivated when the parking brake is engaged.  For vehicles sold in Canada, the DRLs will automatically deactivate when the front fog lights are turned on.  On some vehicles, the Daytime Running Lights may deactivate, or reduce intensity, on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).  \"R\" means radial construction, or \"D\" means", "(when the hazard warning lights are activated).  \"R\" means radial construction, or \"D\" means diagonal or bias construction Apple CarPlay\u00ae is a trademark of Apple\u00ae Inc. iPhone\u00ae is a trademark of Apple\u00ae Inc., registered in the US and other countries.  Apple\u00ae terms of use and privacy statements apply.", "Windshield Wiper Operation Rotate the end of the lever upward to the first detent past the intermittent settings for low-speed wiper operation.  Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation.  CAUTION: In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  Mist Push upward on the wiper lever to activate a single wipe to clear off-road mist or spray from a passing vehicle.  As long as the lever is held up, the wipers will continue to operate.  For information on wiper care and replacement, see Note: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.  The washer function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND", "function must be used in order to spray the windshield with washer fluid.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.  Windshield Washers To use the washer, pull the lever toward you and hold until desired spray is reached.  If the lever is pulled while in the delay range, the wiper will start and continue to operate for two or three wipe cycles after the lever is released.  Then, the intermittent interval previously selected will resume.  If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles.  Then, the wipers will turn off.  Note: As a protective measure, the washer will stop if the switch is held for more than 20 seconds.  Once the switch is released the washer will resume normal operation.  WARNING: Sudden loss of visibility through the windshield", "the washer will resume normal operation.  WARNING: Sudden loss of visibility through the windshield could lead to a collision.  You might not see other vehicles or other obstacles.  To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.  WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column; it operates the multiple wiper options.  The front wipers are operated by rotating a switch, located at the end of the lever.", "If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  To fold down the rear seat, pull the release strap located on the upper outboard side of the rear seat to release the seat.  The", "the release strap located on the upper outboard side of the rear seat to release the seat.  The head restraints are folded independently Position the latch plate as close as possible to the anchor point.  At about 6 to 12 inches (15 to 30 cm) above the latch plate, grab and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.  Slide the latch plate upward over the folded webbing.  The folded webbing must enter the slot at the top of the latch plate.  Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.  Be sure that the front seats are fully upright and positioned forward.  This will allow the rear seat to fold down easily.  The center head restraints must be in the lowest position to avoid contact with the center console when folding the seat.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye", "Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  If required for certain off-road uses, the windshield can be folded down.  However, the protection afforded by the windshield is then lost.  If you fold down the windshield, drive slowly and cautiously.  It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if", "that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down.  The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Do not drive your vehicle on-road with the windshield down.  Do not drive your vehicle unless the windshield is securely fastened, either up or down.  Eye protection, such as goggles, should be worn at all times when the windshield is down.  Be sure that you carefully follow the instructions for raising the windshield.  Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle.  Failure to follow these instructions may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.", "may prevent your vehicle from providing you and your passengers\u2019 protection in some accidents.  If you remove the doors, store them outside the vehicle.  In the event of an accident, a loose door may cause personal injury.  Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving.  Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.  Lowering the soft top lowering the soft top \u00b9 use this qr code to access your digital experience.  If the temperature is below 72\u00b0F (24\u00b0C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up.  This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.  Place the vehicle in a warm area.  Pull steadily on the top fabric.  The vinyl will stretch back to its original size and the top can then be", "on the top fabric.  The vinyl will stretch back to its original size and the top can then be installed.  If the temperature is 41\u00b0F (5\u00b0C) or below, do not attempt to put the top down or roll the rear or side curtains.  WARNING: Do not drive the vehicle with the rear window up/removed unless the quarter windows are also removed.  Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers.  The fabric quarter windows and fabric top are designed only for protection against the elements.  Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident.  Remember, always wear seat belts.  Make sure hands and fingers are clear of all pinch points when installing and removing the soft top.  The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.  CAUTION: The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or", "any additional loads such as roof racks, spare tires, building, hunting or camping supplies, and/or luggage, etc.  Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).  CAUTION: Do not run a fabric top through an automatic car wash.  Window scratches and wax buildup may result.  Do not lower the top when the temperature is below 41\u00b0F (5\u00b0C).  Damage to the top may result.  Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.  Follow the proper steps for cleaning and caring for your vehicle\u2019s fabric top Do not use any tools (screwdrivers, etc.)  to pry or force any of the clamps, clips, or retainers securing the soft top.  Do not force or pry the soft top framework when opening or closing.  Damage to the top may result.  Failure to follow these cautions may cause interior water damage, stains, or mildew on the top material: It is recommended", "cautions may cause interior water damage, stains, or mildew on the top material: It is recommended that the top be free of water prior to opening it.  Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle's interior.  The soft top must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  If you get hung up or high-centered on an object,", "jacking on locations other than those indicated.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.", "get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand,", "brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change", "changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.", "Opening To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The tailgate is dampened to provide a slower, more controlled lowering.  Closing To close the tailgate, lift upward until both sides latch into place.  CAUTION: After closing, pull back on the tailgate firmly to ensure it is securely latched.  Failure to securely latch the tailgate could result in damage to the vehicle or cargo.  Note: If the Tonneau Cover is installed, make sure the Tonneau Cover is fully closed before closing the tailgate.  Due to the presence of the Center High-Mounted Stop Lamp, removal of the tailgate is not recommended.  Secure the tailgate in this position by looping the tailgate straps behind the circular retainer on both sides.  The tailgate is dampened to provide a slower, more controlled lowering.  To open the tailgate, pull the release handle located on the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set", "the center of the tailgate and guide it to the lowered position.  The vehicle\u2019s tailgate can be set to three positions: open, mid, or closed.  The mid position can be used to provide a loading surface for transporting sheet goods.  To use the mid position, open the tailgate and lower it to near mid position.  If the tailgate is lowered, the jack extension with hook can be added to this assembly to enable lowering of the spare tire without having to raise the tailgate.  To close the tailgate, lift upward until both sides latch into place.", "Shifting Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident,", "recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall", "DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals", "Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.", "Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  Tonneau Cover Removal To remove the", "straps are secure, before removing.  Store in a safe location.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.", "be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll", "straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be", "Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  Tonneau Cover Installation To install the Tonneau Cover, proceed as follows: Position the rolled up Tonneau Cover on the truck bed and align it to the two fastener locations at the front of the bed.  Fastener locations using a #t50 torx head driver, secure the fasteners to the bed.  Lower the tailgate to the fully open position before unrolling the Tonneau Cover.  Release the stowage straps used to secure the Tonneau Cover in the rolled up position.  Release stowage strap roll the tonneau cover rearward toward the back of the truck bed.  Roll tonneau cover rearward position both tonneau cover latches over the locking mechanisms (one on each side of the truck bed),", "both tonneau cover latches over the locking mechanisms (one on each side of the truck bed), making sure the plastic retainer is correctly seated in the forward part of the latch.  Correctly seated retainer incorrectly seated retainer once the rear tonneau cover bar is positioned over the locking mechanism, grab the back of the tonneau cover and push downward on the center to engage the locking mechanisms.  Make sure an audible \u201cclick\u201d from both sides of the Tonneau Cover is heard to confirm that the latch is completely engaged.  Push downward to lock note: if desired, the tonneau cover can be left in this position (rear panel folded forward) while the tailgate is closed, or the tailgate can be raised to the mid-position.  Tonneau cover with tailgate in mid-position fold the rear panel down; the tailgate can now be raised and secured in place.  Note: if not leaving the tailgate in the mid-position, the tonneau cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the", "cover must be closed completely prior to fully closing the tailgate.  CAUTION: Do not sit on the Tonneau Cover; damage to the cover and/or cargo will occur.  TONNEAU COVER \u2014 IF EQUIPPED The Tonneau Cover can be installed on the truck bed to keep cargo out of view, and protect from inclement weather.  The tonneau cover consists of the following features: easy roll up cover tonneau fore/aft locator crossbar inside bed locator rear latches stowage straps note: the tonneau cover can be rolled up and secured at the front of the truck bed without removing it completely.  Tonneau Cover Removal To remove the Tonneau Cover, proceed as follows: Open the tailgate.  Fold the rear panel of the Tonneau Cover forward to reveal the red release straps.  Release strap location pull one of the red release straps to release the tonneau cover latch.  Note: pulling either strap will release the latches to roll the tonneau cover up; there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the", "there is no need to pull both at the same time.  Roll the Tonneau Cover forward, starting with the rear bar and continue to roll toward the front of the truck bed.  Roll tonneau cover forward using the stowage straps, secure the tonneau cover in the rolled up position.  Secured tonneau cover using a #t50 torx head driver, remove the two fasteners securing the tonneau cover to the front of the truck bed.  Fastener locations utilizing two people, lift the tonneau cover up and away from the truck bed.  Note: be sure the tonneau cover has been completely rolled up, and straps are secure, before removing.  Store in a safe location.", "Heated Seats \u2014 If Equipped The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  Press the heated seat button once to turn the HI setting on.  Press the heated seat button a second time to turn the MED setting on.  Press the heated seat button a third time to turn the LO setting on.  Press the heated seat button a fourth time to turn the heating elements off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated seats to operate.  The level of heat selected will stay on until the operator changes it.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.  It may cause burns even at low temperatures, especially if used for long periods of time.  Do not place anything on the seat or", "temperatures, especially if used for long periods of time.  Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion.  This may cause the seat heater to overheat.  Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.  Setting name description auto-on driver heated/ventilated seat & heated steering wheel with vehicle start this setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  Remote Start Comfort Systems \u2014 If Equipped When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and", "front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Setting Name Description Auto-On Driver Heated/Ventilated Seat & Heated Steering Wheel With Vehicle Start This setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The", "started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  The engine must be running for the heated steering wheel to operate.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel", "as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings The heated seat control buttons are located on the center instrument panel below the touchscreen and also in the Climate Control touchscreen menu.  The engine must be running for the heated seats to operate.  The level of heat selected will stay on until the operator changes it.  Heated Seat/Vented Seats/Heated Wheel Rear Defroster And Heated Mirrors HVAC System 115 Volt AC Power Inverter System Audio and Telematics System  Setting name description auto-on driver heated/ventilated seat & heated steering wheel with vehicle start this setting will activate the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote", "the vehicle\u2019s comfort system and heated seats or heated steering wheel when the vehicle is remote started or ignition is started.  The \u201cOff\u201d setting will not activate the comfort systems.  The \u201cRemote Start\u201d setting will only activate the comfort systems when using Remote Start.  The \u201cAll Start\u201d setting will activate the comfort systems whenever the vehicle is started.", "Half-Door Installation To install the front or rear half-doors, proceed as follows: Remove the full doors from the vehicle.  For front door removal, see For rear door removal, see Locate the upper and lower hinge pins on the lower half-door, and lower them into the body hinges on the vehicle.  Note: the upper hinge pin is longer, which can be used to assist in guiding the door into place during installation.  Lower half-door hinge pins insert the upper and lower hinge pin screws into the body hinges.  Tighten the screws using a #T50 Torx head driver to 3.8 ft\u00b7 lb / 5.2 N\u00b7m.  Caution: do not close the door before reattaching the door check to the body.  Damage may occur to the door check.  Do not overtighten Torx fasteners, damage to the vehicle\u2019s parts will occur.  Hinge pins can break if overtightened during door install (Max Torque: 6.0 ft\u00b7 lb/8.1 N\u00b7m).  Attach the cloth strap of the lower half-door to the metal hook just inside the vehicle.  Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap connect", "metal hook just inside the vehicle.  Cloth strap attachment 1 \u2014 metal hook 2 \u2014 cloth strap connect the wiring harness on the lower half-door to the connection just inside the vehicle.  Note: for front doors, make sure the wiring harness is closed completely.  Front door wiring harness 1 \u2014 open wiring harness 2 \u2014 closed wiring harness replace wiring access doors.  When the half-doors are shipped with the vehicle, the lower half-doors will have plugs in the post holes that must be removed prior to upper half-door installation.  To remove these plugs, proceed as follows: locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place tool into service hole of plug to remove using the tool, slowly pull upwards from the center of the plug to remove.  Making sure the window on the upper half-door is completely zipped closed, insert the upper half-door into the lower half-door by placing", "is completely zipped closed, insert the upper half-door into the lower half-door by placing the posts into the post holes.  Lower the upper half-door into post holes push down firmly on the inside of the upper half-door until it is fully seated in the lower half.  Push Down To Fully Seat Upper Half-Door  To remove the half-doors, repeat the installation steps in reverse order.  Install the front door frame first.  Ensure the windshield is in the \u201cup\u201d position.  Carefully place the front door frame in the rubber seal at the top of the windshield, and line up the holes for the Torx head fasteners (two for each door).  Swing the frame bracket around the side of the door frame, and insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the following table for the appropriate torque specifications for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners", "for the door frame fasteners.  Tighten Fasteners Target Torque Specification For Torx Fasteners Maximum Minimum 44.2 in-lb (5 N\u00b7m) 53.1 in-lb (6 N\u00b7m) 35.4 in-lb (4 N\u00b7m) Do not overtighten Torx fasteners.  You can strip the fasteners if they are overtightened.  Set the rear door frame pin into the hole on top of the body side, just behind the rear door opening.  Carefully position the top of the door frame onto the rear belt rail and the rear of the front door frame, making sure the rubber seals lie flat.  Ensure the seals are installed correctly to avoid water leaks.  Step Five Step Five Insert the fasteners from underneath.  Tighten with the #T40 Torx head driver until they are snug, being careful not to cross-thread the fasteners or overtighten.  Refer to the previous table for the appropriate torque specifications for the door frame fasteners.  If the check arm is stuck inside the door, follow these instructions to install the check arm.  To reinstall the door(s), perform the previous steps in the reverse", "to install the check arm.  To reinstall the door(s), perform the previous steps in the reverse order.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  To install the front door exterior mirrors on the half-doors, proceed as follows: To install the front or rear half-doors, proceed as follows: Locate the service hole in the center of each plug of the lower half-door (two on each front and rear door).  Place a tool (hook tool or trim stick is recommended) in the service hole.  Place Tool Into Service Hole Of Plug To Remove Using the tool, slowly pull upwards from the center of the plug to remove.  Upon first installation of the half-doors, slowly set the door almost to the closing position and check how the door latch aligns with the body striker.  Touch condition between these components can result in damage to both the door and the", "striker.  Touch condition between these components can result in damage to both the door and the striker.  Only adjust the door to fit correctly against the striker.  DO NOT adjust the striker, as this could affect the positioning of the full door.  Half-doors \u2014 if equipped half-doors \u2014 if equipped \u00b9 use this qr code to access your digital experience.  This vehicle may be equipped with half-doors.  To install the half-doors in the vehicle, follow the instruction sheet packaged in the box the doors were received in.  Replacement parts may be purchased through Mopar\u00ae Service.  CAUTION: Do not run half-doors through an automatic car wash.  This may result in scratches and wax buildup on the windows.  Careless handling and storage of the half-doors may damage the seals resulting in water leaks into the interior of the vehicle.  The upper half-doors must be positioned properly to ensure sealing.  Improper installation can cause water leaks into the interior of the vehicle.  Store the zipper pulls of the upper", "can cause water leaks into the interior of the vehicle.  Store the zipper pulls of the upper half-door windows at the upper B-pillar area for both front and rear doors to avoid damage to the windows when not in use.  Do not attempt to operate the half-door zipper in temperatures of 41\u00b0F (5\u00b0C) or below.  Damage to the window may occur.", "Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial", "DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When", "the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Requirements To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended: WARNING: Improper towing can lead to a collision.  Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel.  When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.  You could lose control of your vehicle and have a collision.  When hauling cargo, or towing a trailer, do not overload your vehicle or trailer.  Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis", "poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires.  Safety chains must always be used between your vehicle and trailer.  Always connect the chains to the frame or hook retainers of the vehicle hitch.  Cross the chains under the trailer tongue and allow enough slack for turning corners.  Vehicles with trailers should not be parked on a grade.  When parking, apply the parking brake on the tow vehicle.  Put the tow vehicle transmission in PARK.  Always block or \"chock\" the trailer wheels.  GCWR must not be exceeded.  Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: gvwr gtw gawr tongue weight rating for the trailer hitch utilized caution: do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven.  The engine, axle or other parts could be damaged.  Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50", "damaged.  Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.  This helps the engine and other parts of the vehicle wear in at the heavier loads.", "When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.", "jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  JUMP STARTING If your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a portable battery booster pack.  Jump starting can be dangerous if done improperly, so please follow the procedures in this section carefully.  WARNING: Do not attempt jump starting if the battery is frozen.  It could rupture or explode and cause personal injury.  CAUTION: Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or", "with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.  Note: When using a portable battery booster pack, follow the manufacturer's operating instructions and precautions.  Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery.  You will never have to add water, and periodic maintenance is not required.  WARNING: Battery fluid is a corrosive acid solution and can burn or even blind you.  Do not allow battery fluid to contact your eyes, skin, or clothing.  Do not lean over a battery when attaching clamps.  If acid splashes in eyes or on skin, flush the area immediately with large amounts of water Battery gas is flammable and explosive.  Keep flame or sparks away from the battery.  Do not use a booster battery or any other booster source with an output greater than 12 Volts.  Do not allow cable clamps to touch each other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash", "other.  Battery posts, terminals, and related accessories contain lead and lead compounds.  Wash hands after handling.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  Serious injury or death could result if you do not disconnect both batteries.  To learn how to properly disconnect, see an authorized dealer.  CAUTION: It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.  Battery posts are marked positive (+) and negative (-) and are identified on the battery case.  Cable clamps should be tight on the terminal posts and free of corrosion.  If a \u201cfast charger\u201d is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.", "connecting the charger to the battery.  Do not use a \u201cfast charger\u201d to provide starting voltage.  Vehicles with the Stop/Start system will be equipped with two batteries.  Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system.  If the negative battery cables are not isolated properly it can cause a potential power spike or surge in the system, resulting in damage to essential electrical components.  Disconnecting the jumper cables disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery.  Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery.  Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery.  Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the", "post of the discharged vehicle.  Reinstall the protective cover over the positive (+) post of the discharged vehicle.  If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer.  CAUTION: Accessories plugged into the vehicle power outlets draw power from the vehicle\u2019s battery, even when not in use (i.e., cellular devices, etc.).  Eventually, if plugged in long enough without engine operation, the vehicle\u2019s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.", "Adaptive Cruise Control (ACC) Operation The buttons on the right side of the steering wheel operate the ACC system.  Adaptive Cruise Control (ACC) is a convenience system.  It is not a substitute for active driver involvement.  It is always the driver\u2019s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.  Your complete attention is always required while driving to maintain safe control of your vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  The ACC system: Does not react to pedestrians, oncoming vehicles, and stationary objects (e.g., a stopped vehicle in a traffic jam or a disabled vehicle).  Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions.  Does not always fully recognize complex driving conditions,", "adverse sight distance conditions.  Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.  ACC The Adaptive Cruise Control (ACC) on/off button is pushed The Fixed Speed Cruise Control on/off button is pushed The ignition is placed in the OFF position 4WD Low is engaged  Using ACC On Hills ACC performance may be limited when driving on hills.  ACC may not detect a vehicle in your lane depending on the speed, vehicle load, traffic conditions, and the steepness of the hill.", "Heated Steering Wheel \u2014 If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  For information on use with the Remote Start system, see Note: The engine must be running for the heated steering wheel to operate.  WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must", "spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  Press the heated steering wheel button once to turn the heating element on.", "wheel if equipped.  Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  The steering wheel contains a heating element that helps warm your hands in cold weather.  The heated steering wheel has only one temperature setting.  Once the heated steering wheel has been turned on, it will stay on until the operator turns it off.  The heated steering wheel may not turn on when it is already warm.  Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater.  It may cause burns even at low temperatures, especially if used for long periods.  Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.  This may cause the steering wheel heater to", "or steering wheel covers of any type and material.  This may cause the steering wheel heater to overheat.  The heated steering wheel button is located on the center of the instrument panel below the radio screen, and within the Climate or Controls screen of the touchscreen.  When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather.  The heated steering wheel and driver heated seat feature will also turn on if programmed in the Comfort menu screen within Uconnect Settings Press the heated steering wheel button once to turn the heating element on.  Press the heated steering wheel button a second time to turn the heating element off.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The engine must be running for the heated steering wheel to operate.", "Anti-Lock Brake System (ABS) Warning Light This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However,", "anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible.  However, the conventional brake system will continue to operate", "is required as soon as possible.  However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should", "by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.  When the parking brake is applied with the ignition switch ON, the Brake Warning Light in the instrument cluster will illuminate.  This warning light will turn on when there's a fault with the EPS system", "When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Depending on the vehicle\u2019s options, feature settings may vary.  Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  Depending on the vehicle\u2019s options, feature settings may vary.  When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Note: depending on the vehicle\u2019s options, feature settings may vary.  When the Reset/Restore Default Settings button is pressed on the touchscreen, the system displays the options related to resetting the Uconnect system", "on the touchscreen, the system displays the options related to resetting the Uconnect system back to its default settings.  These settings can clear personal data and reset selected settings from other menus.  Note: depending on the vehicle\u2019s options, feature settings may vary.  Adjustable Chime Volume Settings The Front and Rear chime volume settings are programmable.  The settings may be programmed through the Uconnect system The chime volume settings include low, medium, and high.  The factory default volume setting is medium.  ParkSense will retain its last known configuration state through ignition cycles.  When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will", "access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Note: depending on the vehicle\u2019s options, feature settings may vary.", "Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Across An Incline If at all possible, avoid driving across an incline.  If it is necessary, know your vehicle's abilities.  Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover.  Make sure the surface has good traction with firm and stable soils.  If possible, transverse the incline at an angle heading slightly up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result", "up or down.  WARNING: Driving across an incline increases the risk of a rollover, which may result in severe injury.  Driving Downhill Before driving down a steep hill, you need to determine if it is too steep for a safe descent.  What is the surface traction?  Is the grade too steep to maintain a slow, controlled descent?  Are there obstacles?  Is it a straight descent?  Is there plenty of distance at the base of the hill to regain control if the vehicle descends too fast?  If you feel confident in your ability to proceed, then make sure you are in 4L and proceed with caution.  Allow engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock.  WARNING: Do not descend a steep grade in NEUTRAL.  Use vehicle brakes in conjunction with engine braking.  Descending a grade too fast could cause you to lose control and be seriously injured or killed.  Off-Road Driving Tips  Driving Up Hill Once you have determined your ability to proceed and have shifted into the", "Tips  Driving Up Hill Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run.  Accelerate with an easy constant throttle and apply more power as you start up the hill.  Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control.  If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground.  As you approach the crest of the hill, ease off the throttle and slowly proceed over the top.  If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than a quarter turn quickly back and forth.  This will provide a fresh \"bite\" into the surface and will usually provide enough traction to complete the climb.  If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle", "vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.  WARNING: Never attempt to climb a hill at an angle or turn around on a steep grade.  Driving across an incline increases the risk of a rollover, which may result in severe injury.", "In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  Example: dot ma l9 abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance", "abcd 0301 dot = department of transportation this symbol certifies that the tire is in compliance with the us department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code representing the tire size (two digits) abcd = code used by the tire manufacturer (one to four digits) 03 = number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.  Example: 031 could represent the 3rd week of 1981 or 1991 American Petroleum Institute (API) Approved Engine Oil These symbols mean that the oil has been certified by the API.  The manufacturer only recommends API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.", "API trademark oils.  The API Starburst trademark certifies 0W-20, 0W-30 and 5W-30 engine oils.  The API Donut trademark certifies 0W-40 and 5W-40 engine oil.  CAUTION: Do not use chemical flushes in your engine oil as the chemicals can damage your engine.  Such damage is not covered by the New Vehicle Limited Warranty.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c.20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause a", "authorized dealer or FCA US LLC.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  In The 50 United States And Washington, D.C.  If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying FCA US LLC.  If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.  However, NHTSA cannot become involved in individual problems between you, an authorized dealer or FCA US LLC.  To contact nhtsa, you may call the vehicle safety hotline toll free at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue,", "or go to http://www.safercar.gov ; or write to: administrator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.c. 20590.  You can also obtain other information about motor vehicle safety from http://www.safercar.gov .", "Carbon Monoxide Warnings WARNING: Carbon monoxide (CO) in exhaust gases is deadly.  Follow the precautions below to prevent carbon monoxide poisoning: Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when", "is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Exhaust gases can injure or kill.  They contain carbon monoxide (CO), which is colorless and odorless.  Breathing it can make you unconscious and can eventually poison you.  To avoid breathing (CO), follow these safety tips: Carbon monoxide (CO) in exhaust gases is deadly.  Follow the precautions below to prevent carbon monoxide poisoning: Exhaust gases can injure or kill.  They contain carbon monoxide (CO), which is colorless and odorless.  Breathing it can make you unconscious and can eventually poison you.  To avoid breathing CO see A hot exhaust system can start a fire if you park over materials that can burn, such as grass or leaves, and those items that come into contact with your exhaust system.  Do not park or operate your vehicle in areas where", "come into contact with your exhaust system.  Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.  For further information For further information For further information The VIN is found on the left front corner of the A-pillar, visible from outside of the vehicle through the windshield.  Android\u2122 is a trademark of Google Inc. es posible que este equipo o dispositivo no cause interferencia perjudicial y este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operaci\u00f3n no deseada.  Exhaust Gas The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.  Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have an authorized dealer inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or", "inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.  Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.  In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change.  Replace as required.  WARNING: Exhaust gases can injure or kill.  They contain carbon monoxide (CO), which is colorless and odorless.  Breathing it can make you unconscious and can eventually poison you.  To avoid breathing (CO), follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.  If you are required to drive with the trunk/liftgate/rear doors open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed.  DO NOT use the recirculation mode.  If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling", "it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle.  Set the blower at high speed.  Carbon Monoxide Warnings WARNING: Carbon monoxide (CO) in exhaust gases is deadly.  Follow the precautions below to prevent carbon monoxide poisoning: Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Charge Air Cooler \u2014 Inter-Cooler (Diesel", "Until repaired, drive with all side windows fully open.  Charge Air Cooler \u2014 Inter-Cooler (Diesel Engine) The charge air cooler is positioned in front of the radiator and the air conditioner condenser.  Air enters the engine through the air cleaner and passes through the turbocharger, where it is pressurized.  This pressurized air rapidly reaches high temperature.  The air is then directed through a hose to the charge air cooler and through another hose to the intake manifold of the engine.  This cooling process enables more efficient burning of fuel resulting in fewer emissions.  To guarantee optimum performance of the system, keep the surfaces of the charge air cooler, condenser and radiator clean and free of debris.  Periodically check the hoses leading to and from the charge air cooler for cracks or loose clamps resulting in loss of pressure and reduced engine performance.", "Get started the vr button is used to activate/deactivate your voice recognition system.  Helpful hints for using Voice Recognition: Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Helpful hints for using Voice Recognition: Voice commands can be used to operate the Uconnect Phone and to navigate its menu structure.  Voice commands are required after most Uconnect Phone prompts.  There are two general methods for how Voice Command works: Prior to giving a voice command, one must wait for the beep, which follows the \u201cListen\u201d prompt or another prompt.  For certain operations, compound commands can be used.  For example,", "prompt or another prompt.  For certain operations, compound commands can be used.  For example, instead of saying \u201cCall\u201d and then \u201cJohn Smith\u201d and then \u201cmobile\u201d, the following compound command can be said: \u201cCall John Smith mobile.\u201d For each feature explanation in this section, only the compound command form of the voice command is given.  You can also break the commands into parts and say each part of the command when you are asked for it.  For example, you can use the compound command form voice command \u201cSearch for John Smith,\u201d or you can break the compound command form into two voice commands: \u201cSearch Contacts\u201d and when asked, \u201cJohn Smith.\u201d Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.  The following basic Voice Commands can be given at any point while using your Uconnect system.  The button on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command", "on your steering wheel is also used to access the Voice Commands for the Uconnect Voice Command features if your vehicle is equipped.  Did you know: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say \u201c help \u201d.  The system provides you with a list of commands.  Did you know: voice command for climate may only be used to adjust the interior temperature of your vehicle.  Voice Command will not work to adjust the heated seats or steering wheel if equipped.  The Voice Command button on your steering wheel is only used for \u201cbarge in\u201d and when you are already in a call or want to make another call.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by", "the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.", "Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  When the Voice button is pressed on the touchscreen, the system displays the options related to the vehicle\u2019s Voice Recognition feature.  Depending on the vehicle\u2019s options, feature settings may vary.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Push and hold the VR button on the steering wheel to activate a Siri voice recognition session.  Apple CarPlay\u00ae allows you to use Siri to send or reply to text messages.  Siri can also read incoming text messages, but drivers will not be able to read messages, as everything is done via voice.  Reduce background noise.  Wind noise and passenger conversations are examples of noise that may impact recognition.  Speak clearly at a normal pace and volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button,", "volume while facing straight ahead.  Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command.  You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold", "which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Push and hold the Voice Recognition (VR) button on the steering wheel until the beep or tap the Microphone icon to ask Google to take you to a desired destination by voice.  You can also touch the Navigation icon in Android Auto\u2122 to access other navigation apps.  Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  Natural Speech Your Uconnect Phone Voice system uses a Natural Language Voice Recognition (VR) engine.  Natural speech allows the user to speak commands in phrases or complete sentences.  The system filters out certain non-word utterances and sounds such as", "or complete sentences.  The system filters out certain non-word utterances and sounds such as \u201cah\u201d and \u201ceh.\u201d The system handles fill-in words such as \u201cI would like to\u201d.  The system handles multiple inputs in the same phrase or sentence such as \u201cmake a phone call\u201d and \u201cto Kelly Smith\u201d.  For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as \u201cWho do you want to call?\u201d in the case where a phone call was requested but the specific name was not recognized.  The system utilizes continuous dialog.  When the system requires more information from the user, it will ask a question to which the user can respond without pushing the Voice Command button on the steering wheel.  Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c", "cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.  Introducing Voice Recognition Start using Uconnect Voice Recognition with these helpful quick tips.  It provides the key Voice Commands and tips you need to know to control your vehicle\u2019s Voice Recognition (VR) system.  If you see the NAV icon on the bottom bar or in the Apps menus of your 8.4-inch touchscreen, you have the Uconnect 4C NAV system.  If not, you have a Uconnect 4C with 8.4-inch display system.  UCONNECT VOICE RECOGNITION Basic Voice Commands The following basic Voice Commands can be given at any point while using your Uconnect system.  Push the VR button After the beep, say: \u201c cancel \u201d to stop a current voice session.  \u201c help \u201d to hear a list of suggested voice commands.  \u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of", "\u201c repeat \u201d to listen to the system prompts again.  Notice the visual cues that inform you of your Voice Recognition system\u2019s status.", "Off-Road Driving Tips  The Basics Of Off-Road Driving You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled", "you are currently driving over.  Note: It is recommended that the Stop/Start system be disabled during off-road use.  WARNING: Always wear your seat belt and firmly tie down cargo.  Unsecured cargo can become projectiles in an off-road situation.  CAUTION: Never park your vehicle over dry grass or other combustible materials.  The heat from your vehicle exhaust system could cause a fire.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  You will encounter many types of terrain driving off-road.  You should be familiar with the terrain and area before proceeding.  There are many types of surface", "should be familiar with the terrain and area before proceeding.  There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.  Every surface has a different effect on your vehicle's steering, handling and traction.  Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture.  Avoid sudden accelerations, turns or braking.  In most cases, there are no road signs, posted speed limits or signal lights.  Therefore, you will need to use your own good judgment on what is safe and what is not.  When on a trail, you should always be looking ahead for surface obstacles and changes in terrain.  The key is to plan your future driving route while remembering what you are currently driving over.  As you approach a hill, consider its grade or steepness.  Determine if it is too steep.  Look to see what the traction is on the hill side trail.  Is the trail straight up and down?", "Look to see what the traction is on the hill side trail.  Is the trail straight up and down?  What is on top and the other side?  Are there ruts, rocks, branches or other obstacles on the path?  Can you safely recover the vehicle if something goes wrong?  If everything looks good and you feel confident, shift the transmission into a lower gear with 4L engaged, and proceed with caution, maintaining your momentum as you climb the hill.  When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires.  This will lift your undercarriage over the obstacle.  The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse.  Always look ahead and make every effort to cross the large rocks with your tires.", "For the proper maintenance intervals see \"\u21e8maintenance plan\" for gas engines or \"\u21e8maintenance plan \u2014 diesel fuel up to b5 biodiesel\" for diesel engines.  Diesel fuel is seldom completely free of water.  To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided on the fuel filter housing.  If you buy good quality fuel and follow the listed cold weather recommendations, fuel conditioners should not be required in your vehicle.  If available in your area, a high cetane \u201cpremium\u201d diesel fuel may offer improved cold-starting and warm-up performance.  A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling.  It is controlled by a built-in thermostat.  A Diesel Pre-Heat system both improves engine starting and reduces the amount of white smoke generated by a warming engine.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the", "maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster", "the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited", "the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle", "avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an", "injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Fuel System Cautions CAUTION: Follow these guidelines to maintain your vehicle\u2019s performance: The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of", "use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  Note: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.", "Shifting Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Shifting Out of N (Neutral) Use the following procedure to prepare your vehicle for normal usage.  Bring the vehicle to a complete stop, leaving it connected to the tow vehicle.  Firmly apply the parking brake.  Start the engine.  Press and hold the brake pedal.  Shift the transmission into NEUTRAL.  Turn the engine off.  Shift the transfer case lever to the desired position.  Note: when shifting the transfer case out of", "the transfer case lever to the desired position.  Note: when shifting the transfer case out of n (neutral), the engine should remain off to avoid gear clash.  Shift the automatic transmission into PARK, or place manual transmission in NEUTRAL.  Release the brake pedal.  Disconnect vehicle from the tow vehicle.  Start the engine.  Press and hold the brake pedal.  Release the parking brake.  Shift the transmission into gear, release the brake pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally.  NEUTRAL (N) Use this range when the vehicle is standing for prolonged periods with the engine running.  Apply the parking brake and shift the transmission into PARK if you must exit the vehicle.  WARNING: Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.  These are unsafe practices that limit your response to changing traffic or road conditions.  You might lose control of the vehicle and have a collision.  CAUTION: Towing the vehicle, coasting, or", "might lose control of the vehicle and have a collision.  CAUTION: Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle N (Neutral) Neutral \u2014 This range disengages both the front and rear driveshafts from the powertrain.  To be used for flat towing behind another vehicleWARNING: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.  The transfer case N (Neutral) position disengages both the front and rear driveshafts from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in PARK (or manual transmission is in gear).  The parking brake should always be applied when the driver is not in the vehicle.  Five-position transfer case \u2014 if equipped the transfer case provides five positions: 2h (two-wheel drive high range) 4h", "case \u2014 if equipped the transfer case provides five positions: 2h (two-wheel drive high range) 4h auto (four-wheel drive auto high range) 4h part time (four-wheel drive part time high range) n (neutral) 4l (four-wheel drive low range) for additional information on the appropriate use of each transfer case position, see the following information:.", "CRUISE CONTROL SYSTEMS \u2014 IF EQUIPPED Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system: Cruise Control will keep your vehicle at a constant preset speed.  Adaptive Cruise Control (ACC) will adjust the vehicle speed up to the preset speed to maintain a distance with the vehicle ahead.  Note: In vehicles equipped with ACC, if ACC is not enabled, Fixed Speed Cruise Control will not detect vehicles directly ahead of you.  Always be aware of the feature selected.  Only one Cruise Control feature can operate at a time.  For example, if Fixed Speed Cruise Control is enabled, Adaptive Cruise Control will be unavailable, and vice versa.  Cruise Control When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  The Cruise Control buttons are located on the right side of the steering wheel.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too", "can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Using Cruise Control On Hills The transmission may downshift on hills to maintain the vehicle set speed.  The Cruise Control system maintains speed up and down hills.  A slight speed change on moderate hills is normal.  On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Cruise Control.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Cruise Control When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20", "When engaged, the Cruise Control system takes over accelerator operations at speeds greater than 20 mph (32 km/h).  The Cruise Control buttons are located on the right side of the steering wheel.  WARNING: Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control", "However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Push the on/off button to activate the Cruise Control.  The cruise indicator light in the instrument cluster display will illuminate.  To turn the system off, push the on/off button a second time.  The cruise indicator light will turn off.  The system should be turned off when not in use.", "See the following steps to use the Manual Park Release: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a", "See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the", "Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  MANUAL PARK RELEASE \u2014 IF EQUIPPED In order to move the vehicle in cases where the transmission will not shift out of Park (P) (such as a depleted battery), a Manual Park Release is available.  See the following steps to use the Manual Park Release: Firmly apply the parking brake.  Using a small screwdriver or similar tool, remove the manual park release cover located in front of the gear selector, to access the release tether strap.  Manual park release cover fish the tether strap up through the opening in the console base.  Tether strap press and maintain firm pressure on the brake pedal.  Pull the tether strap until the release lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can", "lever locks into place in the vertical position.  The vehicle is now out of PARK (P) and can be moved.  Release the parking brake only when the vehicle is securely connected to a tow vehicle.  Vertical Released Position WARNING: Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release.  In addition, you should be seated in the driver\u2019s seat with your foot firmly on the brake pedal when activating the Manual Park Release.  Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake, or by proper connection to a tow vehicle.  Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.  To Reset The Manual Park Release: Pull upward on the tether strap, releasing it from the \u201clocked\u201d position.  Lower the Manual Park Release lever downward into its original position.  Original tether position tuck the tether strap into the base of the", "into its original position.  Original tether position tuck the tether strap into the base of the console, and reinstall the cover.  Extended Park Starting Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.  Press and hold the brake pedal while pushing the ENGINE START/STOP button once.  If the engine fails to start within 10 seconds, place the ignition in the OFF position, wait 10 to 15 seconds to allow the starter to cool, then repeat the \u201cExtended Park Starting\u201d procedure.  If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure.  Note: Extended Park condition occurs when the vehicle has not been started or driven for at least 30 days.  CAUTION: To prevent damage to the starter, do not crank continuously for more than 10 seconds at a time.  Wait 10 to 15 seconds before trying again.", "Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.", "the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by", "operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant", "for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service \"\u21e8if your", "reading does not return to normal, turn the engine off immediately and call for service \"\u21e8if your engine overheats\" .  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control", "help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential", "and call for service.  Cooling System Tips \u2014 Automatic Transmission To reduce the potential for engine and transmission overheating in high ambient temperature conditions, take the following actions: City Driving \u2014 When stopped, shift the transmission into NEUTRAL (N) and increase engine idle speed.  Highway Driving \u2014 Reduce your speed.  Up Steep Hills \u2014 Select a lower transmission gear.  Air Conditioning \u2014 Turn it off temporarily.  Note: if the coolant temperature is too high, the a/c will automatically turn off.  Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  If the light turns on while driving, safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.", "safely pull over and stop the vehicle.  If the Air Conditioning (A/C) system is on, turn it off.  Also, shift the transmission into NEUTRAL and idle the vehicle.  If the temperature reading does not return to normal, turn the engine off immediately and call for service", "Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet", "clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.  Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for", "front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Rear Carpet Remove the grommets under the front seat (one left and one right).  Carpet split then pull the carpet out, to the rear and open the carpet split around the front seat brackets.  Remove the rear Under Seat storage bin (if equipped), by removing the four bolts that hold it to the floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and", "floor.  Remove the fastener bin from the rear floor, it is held in by clips.  Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then lift the assembly out from under the seat.  Lift carpet off of the rear retainers (one left and one right).  Rear retainers remove carpet from the vehicle.  When reinstalling the carpet, perform these steps in reverse order making sure that the carpet is tucked under the scuffs, B-pillar, console, and then refasten the grommets.  Front Carpets: Remove the front grommets.  Front carpet 1 \u2014 grommets pull the carpet out from the front to the rear.  Front carpet pulled away remove the grommets under the front seat.  First for the rear carpet and then the front carpet.  Front and rear carpet split under the back of the front seat, open the carpet split and then pull out the rear edge and slide the carpet to the front (do not remove the harness).  Rear underside of front seat carpet split finally open the carpet split around seat bracket", "Rear underside of front seat carpet split finally open the carpet split around seat bracket and then remove the last two grommets.  When reinstalling carpet, perform these steps in reverse order, making sure that the carpet is tucked under the scuffs, B-pillar, and console, and then refasten the grommets.  Carpet Safety Information Always use carpet designed to fit your vehicle.  Only use carpet that does not interfere with the operation of the pedal assemblies.  Only operate the vehicle when the carpet is securely attached by the grommets so it cannot slip out of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways.  WARNING: If operating the vehicle without carpet in place the floor may become hot, and there is a risk of burns.  An improperly attached, damaged, folded, or damaged grommets may cause your carpet to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS", "or clutch pedals and cause a loss of vehicle control.  To prevent SERIOUS INJURY or DEATH: ALWAYS securely attach your carpet using the grommets.  ALWAYS make sure objects cannot fall or slide into the driver\u2019s side floor area when the vehicle is moving.  Objects can become trapped under accelerator, brake, or clutch pedals and could cause a loss of vehicle control.  NEVER place any objects under the carpet (e.g., towels, keys, etc.).  These objects could change the position of the carpet and may cause interference with the accelerator, brake, or clutch pedals.  ONLY install carpet designed to fit your vehicle.  NEVER install carpet that cannot be properly attached and secured to your vehicle.  If the carpet needs to be replaced, only use manufacturer approved carpet for the specific make, model, and year of your vehicle.  If the vehicle carpet has been removed and re-installed, always properly attach carpet to the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress", "the floor and check that the floor mat fasteners are secure to the vehicle carpet.  Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-install the floor mats.", "OFF-ROAD PAGES \u2014 IF EQUIPPED If your vehicle is equipped with Off-Road Pages, it will provide you vehicle status while operating on off-road conditions.  It supplies information relating to the vehicle ride height, the status of the transfer case, the pitch and roll of the vehicle.  To access Off-Road Pages, press the Apps button on the touchscreen, and then select Off-Road Pages.  OFF-ROAD PAGES \u2014 IF EQUIPPED If your vehicle is equipped with Off-Road Pages, it will provide you vehicle status while operating on off-road conditions.  It supplies information relating to the vehicle ride height, the status of the transfer case, the pitch and roll of the vehicle.  To access Off-Road Pages, press the Apps button on the touchscreen, and then select Off-Road Pages.  Off-Road Pages Status Bar The Off-Road Pages Status Bar is located along the bottom of Off-Road Pages and is present in each of the selectable page options.  It provides information for the following items: transfer case status latitude/longitude", "options.  It provides information for the following items: transfer case status latitude/longitude altitude of the vehicle status of selec-speed control and selected speed in mph (km/h).  Off-Road Driving Tips", "In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  Do not inhale exhaust gases.  They contain carbon monoxide, a colorless and odorless gas, which can kill.  Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.  If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.  Guard against carbon monoxide with proper maintenance.  Have the exhaust system inspected every time the vehicle is raised.  Have any abnormal conditions repaired promptly.  Until repaired, drive with all side windows fully open.  Your vehicle is equipped with a Selective Catalytic Reduction (SCR) system to meet the very stringent diesel emissions standards required by the Environmental Protection Agency.  EMISSIONS INSPECTION", "diesel emissions standards required by the Environmental Protection Agency.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or", "ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently", "is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button", "and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an", "Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a", "to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate", "OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.", "Music apps, playlists, and stations must be set up on your smartphone prior to using Android Auto\u2122 for them to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates", "and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs", "needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android", "the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Plugging in a smartphone device to a USB port may activate Android Auto\u2122 or Apple CarPlay\u00ae features, if equipped.  For further information, refer to the Uconnect Radio Instruction Manual or With Android Auto\u2122 connected, push and hold the VR button on the steering wheel to activate voice recognition specific to Android Auto\u2122.  This allows you to send and reply to text messages, have incoming text messages read out loud, and place and receive hands-free calls.  Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect", "the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and", "with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122", "Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on", "Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Be sure to use the factory-provided USB cable that came with your phone, as aftermarket cables may not work.  Android Auto\u2122 And LTE Data Coverage To use Android Auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone", "the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  How long does it take to sound my horn and flash the lights?  Depending on various conditions, it can take three minutes or more for the request to get through to your vehicle.  Which is faster, my key fob or the Vehicle Branded App?  Your key fob will sound the horn and flash the lights quicker; however, its range is limited.  How do I turn off the horn and lights after I turn them on?  If you are close enough to the vehicle, you can use the key fob to turn off the horn and lights by pressing the red Panic button.  Otherwise, Remote Horn & Lights will continue for a maximum of three minutes.  Why can\u2019t all mobile devices use the Vehicle Branded App?  The Vehicle Branded App has been designed to work on most devices with the Apple\u00ae and Android\u2122 operating systems.  The capabilities of these devices allow us to remotely command your vehicle.", "operating systems.  The capabilities of these devices allow us to remotely command your vehicle.  Other operating systems may be supported in the future.  Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the VR button on the steering wheel, or press and hold the Microphone icon within Android Auto\u2122, to activate its VR, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the", "apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Apple CarPlay\u00ae uses a USB connection while Android Auto\u2122 uses both USB and Bluetooth\u00ae connections to function.  The connected device is unavailable to other devices when connected using Android Auto\u2122 or Apple CarPlay\u00ae.  Once Android Auto\u2122 is up and running on your Uconnect system, the following features can be utilized using your smartphone\u2019s data plan: Android Auto\u2122 allows you to access and stream your favorite music with apps like YouTube Music, iHeartRadio, and Spotify.  Using your smartphone\u2019s data plan, you can stream endless music on the road.", "Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.  SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of", "on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is", "the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke", "and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s", "equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  ASSIST AND SOS SYSTEM \u2014 IF EQUIPPED If equipped, the overhead console contains an ASSIST and an SOS button.  WARNING: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: Your vehicle may", "to do so may result in an accident involving serious injury or death.  Note: Your vehicle may be transmitting data as authorized by the subscriber The ASSIST and SOS buttons will only function if you are connected to an operable LTE (voice/data) or 4G (data) network, which comes as a built-in function.  These and other connected services will only be operable if your SiriusXM Guardian\u2122 service is active and you are connected to an operable LTE (voice/data) or 4G (data) network.  Off Road+ Display \u2014 If Equipped When the Off Road+ button is pushed in the switch bank, the Instrument Cluster Display will begin to show messages related to the feature.  Depending on the Four-Wheel Drive mode in use, the messages will differ, and after five seconds, all messages will clear from the display.  The messages are as follows: 2h: off road+ unavailable, shift to 4wd 4h: 4wd high off road+ active 4l: 4wd low off road+ active adaptive cruise control (acc) and cruise control are not available when using off road+.  If either", "adaptive cruise control (acc) and cruise control are not available when using off road+.  If either option is selected, a dedicated message will display indicating that the features are not usable concurrently.  Messages are as follows: 4h: cruise control \u2014 cruise control unavailable in off road+ 4h: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in off road+ 4l: cruise control \u2014 cruise control unavailable in 4wd low 4l: adaptive cruise control \u2014 adaptive cruise control (acc) unavailable in 4wd low note: the behavior of electronic stability control while in off road+ varies depending on the 4wd status.  If the vehicle is in 4WD High, Traction Control is automatically turned off.  Also, holding the ESC OFF button for five seconds will turn off ESC.  In 4WD Low, Electronic Stability Control automatically shuts off regardless of the Off Road Status.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or", "SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  For further information about the ASSIST and SOS buttons", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  Press the settings button on the touchscreen.  Press the paired phones or audio sources button.  Press to select the particular phone or the particular audio device.  A pop-up menu will appear; press \u201cConnect Phone\u201d.  Press the X to exit out of the Settings screen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The MAX A/C button is only available on", "you to toggle up or down through the available settings.  The MAX A/C button is only available on the touchscreen.  Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, etc.  ), which could scratch the surface.  Do not spray any liquid or chemicals directly on the screen!  Use a clean and dry microfiber lens cleaning cloth in order to clean the touchscreen.  If necessary, use a lint-free cloth dampened with a cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50.  Be sure to follow the solvent manufacturer's precautions and directionsThe SYNC button is only available on the touchscreen.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of", "to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Press the Phone button.  Press the Dial/Keypad button on the touchscreen.  The Touch-Tone screen will be displayed.  Use the numbered buttons on the touchscreens to enter the number and press \u201cDial/Call\u201d.  To access Bluetooth\u00ae Mode, press the Bluetooth\u00ae button on the left side of the touchscreen or under the Source Select/Select Source button (if equipped).  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or", "press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the", "To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.", "will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.", "The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  Bed Rail Tie Down Locations Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.  The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction", "between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Supplemental Seat-Mounted Side Air Bags (SABs) are located in the outboard side of the front seats.  The SABs are marked with a \u201cSRS AIRBAG\u201d or \u201cAIRBAG\u201d on a label or on the seat trim on the outboard side of the seats.  Four auxiliary switches are located in the lower switch bank of the instrument panel and can be used to power various electrical devices.  1 \u2014 Retainers 2 \u2014 Fuel Filter Protective Cover The fold-down windshield on your vehicle is a structural element that can provide protection in some accidents.  The windshield also provides protection against weather, road debris and intrusion of small branches and other objects.  Weight-Distributing Hitch A Weight-Distributing Hitch system works by applying leverage through spring (load) bars.  They are typically used for heavier loads to distribute trailer", "through spring (load) bars.  They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s).  When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.  The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.  Trailer sway control and a Weight-Distributing (load equalizing) Hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements.  WARNING: An improperly adjusted Weight-Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision.  Weight-Distributing Hitch systems may not be compatible with surge brake couplers.  Consult with your", "Hitch systems may not be compatible with surge brake couplers.  Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.  BED RAIL TIE DOWN SYSTEM \u2014 IF EQUIPPED The Bed Rail Tie Down system allows you to properly secure cargo in the truck bed.  There are two adjustable utility rail cleats on each side of the bed that can be used to assist in securing cargo.  Each utility rail cleat must be tightened down in one of the detents along either utility rail in order to keep cargo properly secured.  To move the utility rail cleat to any position on the utility rail, turn the cleat retainer nut counterclockwise several times.  Then, pull out on the utility rail cleat and slide it to the detent nearest the desired location.  Make sure the utility rail cleat is seated in the detent, and tighten the nut.  To remove the utility rail cleats from the side utility rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front", "rails, slide the cleat to the rectangular cutout located at the end of the rail toward the front of the vehicle.  To remove the utility rail cleat from the front utility rail, slide the cleat to the rectangular cutout located on the left side of the rail.  CAUTION: The maximum load per cleat should not exceed 250 lb (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur.  Lower Anchors And Tethers For CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.  The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.  There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.  These anchorages are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some", "are used to install LATCH-equipped child seats without using the vehicle\u2019s seat belts.  Some seating positions may have a top tether anchorage but no lower anchorages.  In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint.  Please see the following table for more information.", "It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have", "speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system:  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of", "Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  The Apple CarPlay\u00ae App plays all compatible apps that are available to use, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Apple CarPlay\u00ae.  Anywhere using your mobile device and Vehicle Branded App From your computer on the Owner\u2019s Site (not available on all functions) Contacting SiriusXM Guardian\u2122 Customer Care (not available on all functions) Select the Vehicle Finder function within the Vehicle Branded App and select the Location tab at the bottom of the App.", "function within the Vehicle Branded App and select the Location tab at the bottom of the App.  Then, press the Vehicle icon to find your vehicle.  Apps The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  Apps The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a", "auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use", "your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may", "depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Description SmartWatch Integration puts the Vehicle Branded App right on your Apple\u00ae Watch or Android\u2122 Wear.  To get started, follow these steps: Download the Vehicle Branded App from the App Store\u00ae or Google Play.  Log onto the app from your smartphone using the username and password you created when you first set up your account.  Make sure your watch and smartphone are connected through Bluetooth\u00ae.  The Vehicle Branded App should appear on your SmartWatch.  Once the app is downloaded on your SmartWatch, you can enjoy these features: Lock or unlock your vehicle by tapping the remote lock button in the app and entering your security PIN.  Remote start or stop your vehicle.  View important vehicle", "the app and entering your security PIN.  Remote start or stop your vehicle.  View important vehicle stats, such as fuel level, vehicle location, tire pressure warning, and more.", "Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Engine Warm-Up Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  If temperatures are below 32\u00b0F (0\u00b0C), operate the engine at moderate speeds for five minutes before full loads are applied.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather,", "a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To", "other controls could cause serious injury or death.  Extreme Cold Weather (Below \u201322\u00b0F Or \u221230\u00b0C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from an authorized dealer) is recommended.  Weather control settings hot weather and vehicle interior is very hot set the mode control to (panel mode), (max a/c) on, and blower on high.  Roll down the windows for a minute to flush out the hot air.  Adjust the controls as needed to achieve comfort.  Warm weather turn (a/c) on and set the mode control to (panel mode).  Cool sunny operate in (bi-level mode).  Cool & humid conditions set the mode control to (mix mode) and turn on (a/c) to keep windows clear.  Cold weather set the mode control to (floor mode).  If windshield fogging starts to occur, move the control to (mix mode).  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system", "the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or", "Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.", "Charging The Speaker Before using the Jeep\u00ae wireless speaker for the first time, fully charge your Jeep\u00ae wireless speaker until the battery indicator light stays solid green.  The Jeep\u00ae wireless speaker in-vehicle dock is the most ideal way to fully charge the speaker with the ignition in ON/RUN or ACC.  The speaker can also be charged with a power adapter.  To charge the Jeep\u00ae wireless speaker with a power adapter, insert the power adapter into a wall outlet.  Next, plug the power adapter into the Jeep\u00ae wireless speaker charging port on the back of the speaker.  Note: Jeep\u00ae wireless speaker will not charge within vehicle dock while the ignition is fully off.  Note: Power adapter needed for the Jeep\u00ae wireless speaker has to have a range of 14 VDC to 16.5 VDC, with a minimum of 2.7A and a barrel connector dimension of 5.5 mm by 2.5 mm.  Power adapter is not included.  Phone & Bluetooth\u00ae Pairing A feature of the Jeep\u00ae wireless speaker is the ability for the Jeep\u00ae wireless speaker to connect to devices using", "Jeep\u00ae wireless speaker is the ability for the Jeep\u00ae wireless speaker to connect to devices using Bluetooth\u00ae.  Follow these simple steps to connect a Bluetooth\u00ae-enabled device to the Jeep\u00ae wireless speaker: Press and hold the power button for 2-3 seconds to turn the Jeep\u00ae wireless speaker on.  Turn \u201con\u201d Bluetooth\u00ae for the device you desire to be connected to the Jeep\u00ae wireless speaker.  For instructions on how to turn on and off Bluetooth\u00ae settings for the desired device, refer to the device\u2019s user manual.  When powered on, the Jeep\u00ae wireless speaker will automatically enter pairing mode.  To pair a second device, press and hold the Bluetooth\u00ae button for 2-3 seconds, until an audio cue is heard.  Then go to the devices\u2019 Bluetooth\u00ae settings and select \u201cJeep\u00ae Speaker\u201d from the list.  The Jeep\u00ae wireless speaker will remember the last eight devices it has paired with.  Note: If the Jeep\u00ae wireless speaker is left on with an inactive Bluetooth\u00ae connection for 30 minutes, it will automatically turn off.  The Jeep\u00ae", "with an inactive Bluetooth\u00ae connection for 30 minutes, it will automatically turn off.  The Jeep\u00ae wireless speaker can be turned on again by pressing and holding the power button for 2-3 seconds.  The Jeep\u00ae wireless speaker is located behind the right rear passenger seat.  In order to access the Jeep\u00ae wireless speaker, the seat will need to be folded down or tilted forward.  A feature of the Jeep\u00ae wireless speaker is the ability for the Jeep\u00ae wireless speaker to connect to devices using Bluetooth\u00ae.  Follow these simple steps to connect a Bluetooth\u00ae-enabled device to the Jeep\u00ae wireless speaker: To remove the Jeep\u00ae wireless speaker, pull on the strap located on top of the mount for the speaker.  When the strap is pulled, the Jeep\u00ae wireless speaker can easily be lifted from the mount.", "Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights.  Once a month or before a long trip: check engine oil level check windshield washer fluid level check the tire pressures and look for unusual wear or damage check the fluid levels of the coolant reservoir, brake master cylinder, and fill as needed check function of all interior and exterior lights once a month or before a long trip: check engine oil level.  Check windshield washer fluid level Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights What to do when an electrical load reduction action", "function of all interior and exterior lights What to do when an electrical load reduction action message is present (\u201cbattery saver on\u201d or \u201cbattery saver mode\u201d) during a trip: reduce power to unnecessary loads if possible: turn off redundant lights (interior or exterior) check what may be plugged in to power outlets +12 volt, 115 volts ac, usb ports check hvac settings (blower, temperature) check the audio settings (volume) after a trip: check if any aftermarket equipment was installed (additional lights, upfitter electrical accessories, audio systems, alarms) and review specifications if any (load and ignition off draw currents).  Evaluate the latest driving cycles (distance, driving time and parking time).  The vehicle should have service performed if the message is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not help to identify the cause.  Never use the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when", "the PARK position as a substitute for the parking brake.  Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage.  Your vehicle could move and injure you and others if it is not in PARK.  Check by trying to move the transmission gear selector out of PARK with the brake pedal released.  Make sure the transmission is in PARK before exiting the vehicle.  The transmission may not engage PARK if the vehicle is moving.  Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking.  Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.  It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.  If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the", "pedal, the vehicle could accelerate quickly forward or in reverse.  You could lose control of the vehicle and hit someone or something.  Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.  Unintended movement of a vehicle could injure those in or near the vehicle.  As with all vehicles, you should never exit a vehicle while the engine is running.  Before exiting a vehicle, always come to a complete stop, then apply the parking brake, shift the transmission into PARK, and turn the ignition OFF.  When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.  When exiting the vehicle, always make sure the ignition is in the OFF position, remove the key fob from the vehicle, and lock the vehicle.  Never leave children alone in a vehicle, or with access to an unlocked vehicle.  Allowing children to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be", "to be in a vehicle unattended is dangerous for a number of reasons.  A child or others could be seriously or fatally injured.  Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.  Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the ACC or ON/RUN position.  A child could operate power windows, other controls, or move the vehicle.  Always do a visual check that your vehicle is in park by looking for the \u201cp\u201d in the instrument cluster display and on the gear selector.  As an added precaution, always apply the parking brake when exiting the vehicle.  Check engine oil level.  Check windshield washer fluid level.  Check the tire pressures and look for unusual wear or damage, rotate at the first sign of irregular wear.  Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and fill as needed.  Check function of all interior and exterior lights.", "Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.", "the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by", "operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant", "for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Instrument cluster descriptions tachometer indicates the engine speed in revolutions per minute (rpm x 1000).  Caution: do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature gauge the temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others", "of the normal operating range.  Warning: a hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Caution: driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument cluster display the instrument cluster display features a driver interactive display.  Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer indicates vehicle speed.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to", "indicates vehicle speed.  IF YOUR ENGINE OVERHEATS If the vehicle is overheating, it will need to be serviced by an authorized dealer.  Potential signs of vehicle overheating: temperature gauge is at hot (h) strong smell of coolant white smoke coming from engine or exhaust coolant bottle coolant has bubbles present in the event it is observed that the temperature gauge is moving towards or close to the hot (h) position, you can reduce the potential for overheating by taking the appropriate action.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement", "to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  WARNING: You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.  If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.  Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.  CAUTION: Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  Accessory Gauge The Accessory Gauge page displays the current status of the vehicle\u2019s Coolant Temperature, Oil Temperature, Oil Pressure, Transmission Temperature, and", "of the vehicle\u2019s Coolant Temperature, Oil Temperature, Oil Pressure, Transmission Temperature, and Battery Voltage.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper", "up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle", "to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized", "range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.", "Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II.  This system monitors the performance of the emissions, engine, and transmission control systems.  When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.  Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all", "system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle's emissions control system.  Failure to pass could prevent vehicle registration.  For states and/or provinces that require an Inspection and Maintenance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a", "testing.  The obd ii system may not be ready if your vehicle was recently serviced, recently had a depleted battery or a battery replacement.  If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  Note: if you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you", "ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  If your obd ii system is not ready, you should see an authorized dealer or repair facility.  If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.  A recheck with the previously mentioned test routine may then indicate that the system is now ready.  Regardless of whether your vehicle's OBD II system is ready, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the", "going to the I/M station.  The I/M station can fail your vehicle because the MIL is on with the engine running.  Keyless Enter \u2018n Go\u2122 Ignition This feature allows the driver to operate the ignition switch with the push of a START/STOP ignition button as long as the key fob is in the passenger compartment.  The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position.  These modes are OFF, ACC, RUN, and START.  The push button ignition can be placed in the following modes: Enhanced Accident Response System Reset Procedure In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.  Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.  After an accident, if the vehicle will not start after performing the reset procedure, the", "engine.  After an accident, if the vehicle will not start after performing the reset procedure, the vehicle must be towed to an authorized dealer to be inspected and to have the Enhanced Accident Response System reset.  Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.  To check if your vehicle's OBD II system is ready, you must do the following: Cycle the ignition switch to the ON position, but do not crank or start the engine.  If you crank or start the engine, you will have to start this test over.  As soon as you cycle the ignition switch to the ON position, you will see the Malfunction Indicator Light (MIL) symbol come on as part of a normal bulb check.  Approximately 15 seconds later, one of two things will happen: The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine.  This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m", "This means that your vehicle's obd ii system is not ready and you should not proceed to the i/m station.  The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.  This means that your vehicle's obd ii system is ready and you can proceed to the i/m station.  Prolonged driving with the MIL on could cause further damage to the emission control system.  It could also affect fuel economy and driveability.  The vehicle must be serviced before any emissions tests can be performed.  If the MIL is flashing while the vehicle is running, severe catalytic converter damage and power loss will soon occur.  Immediate service is required.", "Passengers should not remain in the vehicle when the vehicle is being jacked in position.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Do not attempt to raise the vehicle by jacking on locations other than those indicated.  Jacking and tire changing jacking and tire", "by jacking on locations other than those indicated.  Jacking and tire changing jacking and tire changing \u00b9 use this qr code to access your digital experience.  WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  If you get hung up or high-centered on an object, get out of", "only.  Avoid ice or slippery areas.  If you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.  Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down.  You can also try rocking the vehicle or winching the vehicle off the object.  Do not attempt to change a tire on the side of the vehicle close to moving traffic.  Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.  Being under a jacked-up vehicle is dangerous.  The vehicle could slip off the jack and fall on you.  You could be crushed.  Never put any part of your body under a vehicle that is on a jack.  If you need to get under a raised vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or", "vehicle, take the vehicle to a service center where it can be raised on a lift.  Never start or run the engine while the vehicle is on a jack.  The jack is designed to be used as a tool for changing tires only.  The jack should not be used to lift the vehicle for service purposes.  The vehicle should be jacked on a firm level surface only.  Avoid ice or slippery areas.  Completely inspect the underbody of your vehicle.  Check tires, body structure, steering, suspension, driveline, and exhaust system for damage.  Inspect the radiator for mud and debris and clean as required.  Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and suspension.  Retighten them, if required, and torque to the values specified in the Service Manual.  Check for accumulations of plants or brush.  These things could be a fire hazard.  They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar", "axle pinion seals, and propeller shafts.  After extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible.  Inspect the clutch vent holes in the manual transmission bell housing for mud and debris and clean as required.  Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.  You might not have full braking power when you need it to prevent a collision.  If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.  If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.  Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation.", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press", "Low.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the", "km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that", "while in 4WD Low.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the", "Manual Activation Of The TrailCam TrailCam view can be activated via the below methods: Press the FWD Camera button on the controls screen.  Press the Forward Facing Camera button on the apps menu.  Press the TrailCam button on the Off Road Pages.  Press the Off Road+ button when Auto Launch Off Road+ (if equipped) has been selected under camera settings.  The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  When the vehicle is shifted out of REVERSE with Camera Delay turned off and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera Delay turned on and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen", "transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the TrailCam view is pressed.  Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Note: If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.  The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to", "Low.  Cleaning The TrailCam Press and hold the Clean Camera button located on the TrailCam view to wash the TrailCam.  Washer fluid will stop when the button is released.  The camera can be washed up to 20 seconds at a time while holding the button.  The Clean Camera system is not available when windshield washing is in process.  When enabled, active dynamic Tire Lines are projected on the ground plane of the TrailCam view based on the steering wheel position.  TRAILCAM SYSTEM \u2014 IF EQUIPPED Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle.  The image will be displayed on the touchscreen display along with a caution note \u201cCheck Entire Surroundings\u201d across the top of the screen.  The TrailCam system has programmable settings that may be selected through the Uconnect system Note: The system will stay active while in 4WD Low.", "SOS Call Push the SOS Call button on the overhead console.  Note: in case the sos call button is pushed in error, there will be a 10 second delay before the sos call system initiates a call to an sos operator.  To cancel the SOS Call connection, push the SOS call button on the overhead console or press the cancellation button on the Device Screen.  Termination of the SOS Call will turn off the green LED light on the overhead console.  The LED light located within the ASSIST and SOS buttons on the overhead console will turn green once a connection to an SOS operator has been made.  Once a connection between the vehicle and an sos operator is made, the sos call system may transmit the following important vehicle information to an sos operator: indication that the occupant placed an sos call.  The vehicle brand.  The last known GPS coordinates of the vehicle.  You should be able to speak with the SOS operator through the vehicle audio system to determine if additional help is needed.  Warning: always obey", "through the vehicle audio system to determine if additional help is needed.  Warning: always obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Note: your vehicle may be transmitting data as authorized by the subscriber.  Once a connection is made between the vehicle\u2019s SOS Call system and the SOS operator, the SOS operator may be able to open a voice connection with the vehicle to determine if additional help is needed.  Once the SOS operator opens a voice connection with the vehicle\u2019s SOS Call system, the operator should be able to speak with the vehicle occupants, and hear sounds occurring in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS", "in the vehicle.  The vehicle\u2019s SOS Call system will attempt to remain connected with the SOS operator until the SOS operator terminates the connection.  The SOS operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates.  WARNING: If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from an Emergency Services Agent.  All occupants should exit the vehicle immediately and move to a safe location.  Never place anything on or near the vehicle\u2019s operable network and GPS antennas.  You could prevent operable network and GPS signal reception, which can prevent your vehicle from placing an emergency call.  An operable network and GPS signal reception is required for the SOS Call system to function properly.  The SOS Call system is embedded into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s", "into the vehicle\u2019s electrical system.  Do not add aftermarket electrical equipment to the vehicle\u2019s electrical system.  This may prevent your vehicle from sending a signal to initiate an emergency call.  To avoid interference that can cause the SOS Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.)  to your vehicle\u2019s electrical system or modify the antennas on your vehicle.  IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.  Modifications to any part of the SOS Call system could cause the air bag system to fail when you need it.  You could be injured if the air bag system is not there to help protect you.  Connected Services SOS FAQs \u2014 If Equipped What happens if I accidentally push the SOS Call button on the mirror or overhead console?  You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call,", "You have 10 seconds after pushing the SOS Call button to cancel the call.  To cancel the call, either push the SOS Call button again, or press the Cancel button on the in-vehicle touchscreen.  What type of information is sent when I use the SOS Call button from my vehicle?  Certain vehicle information, such as make and model, is transmitted along with the last known GPS location.  When could I use the SOS Call button?  You can use the SOS Call button to make a call if you or someone else needs emergency assistance.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  For further information about the ASSIST and SOS buttons The ASSIST button is used to automatically connect you to any one of the following support centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button", "centers: 1 \u2014 Assist Button 2 \u2014 SOS Button If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.", "Driver Assist \u2014 If Equipped The Driver Assist menu displays the status of the ACC system.  Push and release the up or down arrow button until the driver assist menu is displayed in the instrument cluster display.  The Driver Assist menu displays the status of the ACC system.  Push and release the up or down arrow button until the driver assist menu is displayed in the instrument cluster display.  Simply push the ASSIST button in the vehicle and you will be presented with your ASSIST options on the touchscreen.  Make your selection by pressing the touchscreen.  When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Depending on the", "the available options related to that feature will then display on the screen.  Depending on the vehicle\u2019s options, feature settings may vary.  If equipped, vehicles with an ASSIST and an SOS button are connected vehicles.  These buttons will be located on either the rearview mirror or overhead console, depending on the vehicle.  If these buttons are present in your vehicle, you have a connected radio and can take advantage of the many connected vehicle features.  If equipped, the ASSIST Button is used for contacting Roadside Assistance, Vehicle Care, Uconnect Care, and SiriusXM Guardian\u2122 Customer Care.  The SOS Call button connects you directly to SiriusXM Guardian\u2122 Customer Care for assistance in an emergency.  The light located within the ASSIST and SOS buttons will continuously be illuminated red.  The Device Screen will display the following message \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please", "dealer.\u201d An In-Vehicle Audio message will state \u201cVehicle device requires service.  Please contact an authorized dealer.\u201d With SiriusXM Guardian\u2122, your vehicle has onboard assistance features located on the rearview mirror or overhead console designed to enhance your driving experience if you should ever need assistance or support.  Favorite Menus Speedometer Vehicle Info Off Road \u2014 If Equipped (show/hide) Driver Assist \u2014 If Equipped (show/hide) Fuel Economy (show/hide) Trip Info (show/hide) Stop / Start \u2014 If Equipped Audio (show/hide) Messages Screen Setup Vehicle Settings \u2014 If Equipped What is the phone number for roadside assistance call?  The phone number is: US: 1-800-521-2779 Canada: 1-800-363-4869 If I am subscribed to SiriusXM Guardian\u2122, does it cover towing or other expenses incurred by using roadside assistance?  No, however your new vehicle may include Roadside Assistance Call services.  SAFETY FEATURES When the Safety/Driving Assistance button is selected on the touchscreen, the system displays", "When the Safety/Driving Assistance button is selected on the touchscreen, the system displays the options related to the vehicle\u2019s safety settings.  These options will differ depending on the features equipped on the vehicle.  The settings may display in list form or within subfolders on the screen.  To access a subfolder, select the desired folder; the available options related to that feature will then display on the screen.  Note: depending on the vehicle\u2019s options, feature settings may vary.  OCCUPANT RESTRAINT SYSTEMS Some of the most important safety features in your vehicle are the restraint systems:", "With Remote Start, the engine will only run for 15 minutes.  Remote Start can only be used twice.  If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.  The parking lights will turn on and remain on during Remote Start mode.  For security, power window operation is disabled when the vehicle is in the Remote Start mode.  The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.  For information on use with the Remote Start system, see These features will stay on through the duration of Remote Start, or until the ignition is placed in the ON/RUN position.  The climate control settings will change if manually adjusted by the driver while the vehicle is in remote start mode.  This includes turning the climate controls off using the OFF button.  Description The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any", "you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  You can also send a command to turn off an engine that has been started using Remote Vehicle Start.  After 15 minutes, if you have not entered your vehicle with the key, the engine will shut off automatically.  This remote function requires your vehicle to be equipped with a factory-installed Remote Start system.  You can set up push notifications every time a command is sent to activate or cancel Remote Start.  REMOTE START \u2014 IF EQUIPPED (DIESEL) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of approximately 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be", "climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.  WARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  REMOTE START \u2014 IF EQUIPPED (GASOLINE) This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security.  The system has", "the engine conveniently from outside the vehicle while still maintaining security.  The system has a range of 328 ft (100 m).  Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the driver enters the vehicle.  Note: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and key fob may reduce this rangeWARNING: Do not start or run an engine in a closed garage or confined area.  Exhaust gas contains carbon monoxide (CO) which is odorless and colorless.  Carbon monoxide is poisonous and can cause serious injury or death when inhaled.  Keep key fobs away from children.  Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.  In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.  If the wiper switch is left on and the wipers freeze", "park position before turning off the engine.  If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.  The Remote Vehicle Start feature provides you with the ability to start the engine on your vehicle without the keys and from virtually any distance.  Once started, the preset climate controls in your vehicle can warm up or cool down the interior.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  Avoid full throttle operation when the engine is cold.  When starting a cold engine, bring the engine up to operating speed slowly to allow the oil pressure to stabilize as the engine warms up.  The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.  Obstructions between the vehicle and the key fob may reduce this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish", "this range.  The Remote Start system will wait for the Wait To Start yellow telltale to extinguish before cranking the engine This allows time for the engine preheat cycle to heat the cylinder air, and is normal in cold weather.", "The trailcam view can also be activated by pressing the icon on the back up camera view.  The back up camera view can also be activated by pressing the icon on the trailcam view.  If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rearview mirror.  They may require cleaning or removal of an obstruction.  Rear Cross Path Detection (RCP) is not a backup aid system.  It is intended to be used to help a driver detect an oncoming vehicle in a parking lot situation.  Drivers must be careful when backing up, even when using RCP.  Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up.  Failure to do so can result in serious injury or death.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a", "button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  Different colored zones indicate the distance to the rear of the vehicle.  The ParkView Rear Back Up Camera allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is in REVERSE.  The image will be displayed in the touchscreen display along with a caution note to \u201cCheck Entire Surroundings\u201d across the top of the screen.  After five seconds this note will disappear.  The ParkView camera is located on the tailgate, above the vehicle license plate.  Manual Activation Of The Rear View Camera Go to the Controls screen by pressing the Controls button located on the bottom of the Uconnect display, and then press Back Up Camera.  Press the Back Up Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE", "Camera button to turn the Rear View Camera system on.  When the vehicle is shifted out of REVERSE with Camera delay turned off, the rear Camera mode is exited and the previous screen appears again.  When the vehicle is shifted out of REVERSE with Camera delay turned on, the rear Camera image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen X button to disable display of the Rear View Camera image is pressed.  Whenever the Rear View Camera image is activated through the Back Up Camera button in the Controls menu, and the vehicle speed is greater than, or equal to 8 mph (13 km/h), a display timer for the image is initiated.  The image will continue to be displayed until the display timer exceeds 10 seconds.  When enabled, active guidelines are overlaid on the image to illustrate the width of the vehicle and its projected back up path based on the steering wheel position.", "the width of the vehicle and its projected back up path based on the steering wheel position.  A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.  Different colored zones indicate the distance to the rear of the vehicle.  The following table shows the approximate distances for each zone: Note: If the vehicle speed remains below 8 mph (13 km/h), the Rear View Camera image will be displayed continuously until deactivated via the touchscreen X button, the transmission is shifted into PARK, or the ignition is placed in the OFF position.  The touchscreen X button to disable display of the camera image is made available ONLY when the vehicle is not in REVERSE.  WARNING: Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.  Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.  You are responsible for the", "other vehicles, obstructions, or blind spots before backing up.  You are responsible for the safety of your surroundings and must continue to pay attention while backing up.  Failure to do so can result in serious injury or death.  CAUTION: To avoid vehicle damage, ParkView should only be used as a parking aid.  The ParkView camera is unable to view every obstacle or object in your drive path.  To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen.  It is recommended that the driver look frequently over his/her shoulder when using ParkView.  Note: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.  Do not cover the lens.", "Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently", "ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  VEHICLE MODIFICATIONS/ALTERATIONS WARNING: Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in", "methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as ethanol.  Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void the New Vehicle Limited Warranty.  CAUTION: DO NOT use E-85, gasoline containing methanol, or gasoline containing more than 15% ethanol (E-15).  Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator", "cause emissions to exceed the applicable standard, and/or cause the Malfunction Indicator Light to illuminate.  Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15).  Do Not Use E-85 In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15).  Use of gasoline with higher ethanol content may void the New Vehicle Limited Warranty.  If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: Operate in a lean mode.  OBD II Malfunction Indicator Light on.  Poor engine performance.  Poor cold start and cold drivability.  Increased risk for fuel system component corrosion.  Reformulated Gasoline Many areas of the country require the use of cleaner-burning gasoline referred to as \u201creformulated gasoline\u201d.  Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.  The use of", "and are specifically blended to reduce vehicle emissions and improve air quality.  The use of reformulated gasoline is recommended.  Properly blended reformulated gasoline will provide improved performance and durability of engine and fuel system components.", "For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  See Engine Fluids and Lubricants for the correct engine oil viscositySynthetic engine oils which do not have both the correct API trademark and the correct SAE viscosity grade numbers should not be used.  Lubricant should be approximately 1/8 inch (3 mm) below the bottom edge of the oil fill hole.  Use only the manufacturer\u2019s recommended fluid Trac-Lok is especially helpful during slippery driving conditions.  With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction.  Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure", "may increase from 2 to 6 psi (13 to 40 kPa) during operation.  DO NOT reduce this normal pressure build-up or your tire pressure will be too low.  1 \u2014 Coolant Temperature 2 \u2014 Oil Temperature 3 \u2014 Battery Voltage 4 \u2014 Transmission Temperature 5 \u2014 Oil Pressure Operation in ambient temperature below 32\u00b0F (0\u00b0C) may require special considerations.  The following charts suggest these options:  Use only the manufacturer\u2019s recommended fluid For the recommended viscosity and quality grades seeThe engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality gradesNON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will", "should be consistent with anticipated climate conditions under which vehicle operations will occur.  The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.  Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.  For recommended viscosity and quality grades NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as", "illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).", "Outside Air Intake Make sure the air intake, located directly in front of the windshield, is free of obstructions, such as leaves.  Leaves collected in the air intake may reduce airflow, and if they enter the air distribution box, they could plug the water drains.  In Winter months, make sure the air intake is clear of ice, slush, and snow.  Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather.  To clear the windows, select Defrost or Mix mode and increase the front blower speed.  Do not use the Recirculation mode without A/C for long periods, as fogging may occur.  On the highways \u2014 slow down.  In city traffic \u2014 while stopped, place the transmission in NEUTRAL (N), but do not increase the engine idle speed while preventing vehicle motion with the brakes.  If your Air Conditioner (A/C) is on, turn it off.  The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat,", "the A/C off can help remove this heat.  You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.  This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.  For Manual Climate Controls, if the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows.  If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.  If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.  Clean with a gentle water spray from the front of the radiator and through the condenser.  In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the", "a scorching odor may suggest severe and abnormal catalyst overheating.  If this occurs, stop the vehicle, turn off the engine and allow it to cool.  Service, including a tune-up to manufacturer's specifications, should be obtained immediately.", "Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.", "your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil", "to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no", "completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator", "within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To", "this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will", "(805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on", "system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak", "a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by", "or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.  Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a", "indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.  A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below", "Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.  The light will remain on until the cause is corrected.  If brake failure is indicated, immediate repair is necessary.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily", "is applied with the ignition switch in the ON/RUN position.  Note: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions.  The vehicle should have service performed, and the brake fluid level checked.  WARNING: Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  Note: This light shows only that the parking brake is applied.  It does not show the degree of brake application.  Brake System Warning Light The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the", "is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Anti-Lock Brake System (ABS) Warning Light The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  If the Brake System Warning Light remains on or comes on while driving, it indicates that the brake system is not functioning properly", "on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is required.  If the Brake System Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position.  The light should illuminate for approximately two seconds.  The light should then turn off unless the parking brake is applied or a brake fault is detected.  If the light does not illuminate, have the light inspected by an authorized dealer.  This warning light will illuminate to signal a fault with the 4WD system.  If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.  It is recommend you drive to the nearest service center and have the vehicle serviced immediately.  This warning light monitors various brake functions,", "and have the vehicle serviced immediately.  This warning light monitors various brake functions, including brake fluid level and parking brake application.  If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir.  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  This light may turn on if the accelerator and brake pedals are pressed at the same time.  The red Brake System Warning Light will turn on when the ignition is placed in the ON/RUN mode, and may stay on for as long as four seconds.  If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible", "and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system.  In this case, the light will remain on until the condition has been corrected.  If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.  Driving a vehicle with the red brake light on is dangerous.  Part of the brake system may have failed.  It will take longer to stop the vehicle.  You could have a collision.  Have the vehicle checked immediately.  If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated.  Have the brake system serviced by an authorized dealer immediately.", "Apps The Android Auto\u2122 App displays all the compatible apps that are available to use with Android Auto\u2122, every time it is launched.  You must have the compatible app downloaded, and you must be signed in to the app through your mobile device for it to work with Android Auto\u2122.  Refer to https://play.google.com/store/apps/ to see the latest list of available apps for android auto\u2122.  Android auto\u2122 android auto\u2122 \u00b9 use this qr code to access your digital experience.  Android Auto\u2122 is a feature of your Uconnect system, and your Android\u2122 6.0 or higher powered smartphone with a data plan, that allows you to project your smartphone and a number of its apps onto the touchscreen radio display.  Android Auto\u2122 brings you useful information, and organizes it into simple cards that appear just when they are needed.  Android Auto\u2122 can be used with speech technology, the steering wheel controls, the knobs and buttons on your radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android", "radio faceplate, and the radio display\u2019s touchscreen to control many of your apps.  To use Android Auto\u2122, perform the following procedure: Download the Android Auto\u2122 app from the Google Play store on your Android\u2122-powered smartphone.  Connect your Android\u2122-powered smartphone to one of the media USB ports in your vehicle.  If the Android Auto\u2122 app was not downloaded, the first time you plug your device in the app begins to download.  Your vehicle should be in PARK the first time you use the app.  Note: be sure to use the factory-provided usb cable that came with your phone, as aftermarket cables may not work.  Android auto\u2122 and lte data coverage note: to use android auto\u2122, make sure you are in an area with cellular coverage.  Android Auto\u2122 may use cellular data and your cellular coverage is shown in the upper right corner of the radio screen.  Data plan rates apply.  Once the device is connected and recognized, the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122", "the Phone icon on the drag & drop menu bar changes to the Android Auto\u2122 icon.  Once android auto\u2122 is up and running on your uconnect system, the following features can be utilized using your smartphone\u2019s data plan: google maps\u2122 for navigation youtube music, spotify, iheart radio, etc.  For music hands-free calling and texting for communication various compatible apps note: feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: Android Auto\u2122 is set to launch immediately once a compatible device is connected.  You can also launch it by pressing the Android Auto\u2122 icon on the touchscreen.  Description SmartWatch Integration puts the Vehicle Branded App right on your Apple\u00ae Watch or Android\u2122 Wear.  To get started, follow these steps: Download the Vehicle Branded App from the App Store\u00ae or Google Play.  Log onto the app from your smartphone using the username and password you created when you first", "Log onto the app from your smartphone using the username and password you created when you first set up your account.  Make sure your watch and smartphone are connected through Bluetooth\u00ae.  The Vehicle Branded App should appear on your SmartWatch.  Once the app is downloaded on your SmartWatch, you can enjoy these features: Lock or unlock your vehicle by tapping the remote lock button in the app and entering your security PIN.  Remote start or stop your vehicle.  View important vehicle stats, such as fuel level, vehicle location, tire pressure warning, and more.  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon", "of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc.Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .  Android", "plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .  Android Auto\u2122 Voice Command Android Auto\u2122 allows you to use your voice to interact with its best-in-class speech technology through your vehicle\u2019s voice recognition system, and use your smartphone\u2019s data plan to project your Android\u2122-powered smartphone and a number of its apps onto your Uconnect touchscreen.  Connect your Android\u2122 6.0 or higher to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto\u2122 icon that replaces your Phone icon on the main menu bar to begin Android Auto\u2122.  Push and hold the vr button on the steering wheel, or press and hold the microphone icon within android auto\u2122, to activate its vr, which recognizes natural voice commands, to use a list of your smartphone\u2019s features: maps music phone text messages additional apps android\u2122 is a trademark of google inc. Note: Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122", "Feature availability depends on your carrier and mobile phone manufacturer.  Some Android Auto\u2122 features may or may not be available in every region and/or language.  Note: To use Android Auto\u2122 on your car display, you\u2019ll need an Android\u2122 phone running Android\u2122 6.0 or higher, an active data plan, and the Android Auto\u2122 app.  To wirelessly use Android Auto\u2122 on your car display, you need a compatible Android\u2122 smartphone with an active data plan.  You can check which smartphones are compatible at g.co/androidauto/requirements .", "Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.  When TSC is functioning, the ESC Activation/Malfunction Indicator Light will flash, the engine power may be reduced, and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying.  TSC is disabled when the ESC system is in the \u201cPartial Off\u201d or \u201cFull Off\u201d modes.  Note: TSC cannot stop all trailers from swaying.  Always use caution when towing a trailer and follow the trailer tongue weight recommendations.  See \"\u21e8trailer towing\" for further information.  WARNING: If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway.  Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction", "between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Trailer Sway Control (TSC) \u2014 If Equipped The TSC is a telescoping link that can be installed between the hitch receiver and the trailer tongue.  It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.  Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.  It also allows you to lengthen or shorten the steering column.  The tilt/telescoping control is located below the steering wheel at the end of the steering column.  To unlock the steering column, push the control downward (toward the floor).  To tilt the steering column, move the steering wheel upward or downward as desired.  To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as", "To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.  To lock the steering column in position, push the control upward until fully engaged.  WARNING: Do not adjust the steering column while driving.  Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.  Failure to follow this warning may result in serious injury or death.", "When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  The Favorites menu provides a means to edit the Favorites list and to configure the Alert Settings, along with providing a list of Channels currently airing any of the items in the Favorites list.  They allow you to change the Main Screen area and Menu Title area.  The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.  While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward.  Release the bar once you have", "under the seat cushion and move the seat forward or rearward.  Release the bar once you have reached the desired position.  Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.  Press the Game Zone button, located at the left of the Browse screen.  This feature provides you with the ability to select teams, edit the selection, and set alerts.  Press the Favorites button on the touchscreen to activate the favorites menu, which will time out within 20 seconds in absence of user interaction.  Press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Push the ok button to access/select the information screens or submenu screens of a main menu item.  To reset displayed/selected features push and hold the ok button for two seconds.  Once in the Browse Presets screen, you can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow", "can scroll the preset list by rotation of the TUNE/SCROLL knob or by pressing the Up or Down Arrow key, located on the right of the screen.  Using the up or down arrow button allow you to cycle through the main menu items.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Setting Name Description Display Mode This setting will allow you to set the brightness manually or have the system set it automatically.  The \u201cAuto\u201d setting has the system automatically adjust the display brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.", "brightness.  The \u201cManual\u201d setting will allow the user to adjust the brightness of the display.  Display Brightness With Headlights ON/Brightness This setting will allow you to set the brightness when the headlights are on.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Display Brightness With Headlights OFF/Brightness This setting will allow you to set the brightness when the headlights are off.  To access this setting, Display Mode must be set to Manual.  The \u201c+\u201d setting will increase the brightness; the \u201c-\u201d will decrease the brightness.  Set Theme This setting will allow you to change the display theme.  Keyboard This setting will change the keyboard type on the display.  The selectable keyboards are \u201cABCDEF Keyboard\u201d, \u201cQWERTY Keyboard\u201d, and \u201cAZERTY Keyboard\u201d.  Touchscreen Beep This setting will allow you to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the", "to turn the touchscreen beep on or off.  Control Screen Timeout This setting allows you to set the Control Screen to turn off automatically after five seconds or stay open until manually closed.  Navigation Next Turn Pop-ups Displayed in Cluster This setting will display navigation prompts in the Instrument Cluster Display.  Phone Pop-ups Displayed In Cluster This setting will display smartphone notifications and messages in the Instrument Cluster Display.  Auto Launch with Off-Road+ This setting will determine how the Off-Road feature is launched through the radio when turning the vehicle on.  The options are \u201cOff\u201d, \u201cForward Camera\u201d (if equipped), and \u201cOff Road Pages\u201d.  In Bluetooth\u00ae Mode, press and release the Seek Up button on the touchscreen for the next selection on the Bluetooth\u00ae device.  Press and release the Seek Down button on the touchscreen to return to the beginning of the current selection, or return to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second", "to the beginning of the previous selection if the Bluetooth\u00ae device is within the first second of the current selection.  Drag & Drop Menu Bar The Uconnect features and services in the main menu bar are easily customized for your preference.  Simply follow these steps: press the apps button to open the app screen.  Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar.  Note: This feature is only available if the vehicle is in PARK.  Uconnect 4 with 7-inch display and uconnect 4/4c/4c nav with 8.4-inch display press the apps button, then press the settings button on the touchscreen to display the menu setting screen.  In this mode the Uconnect system allows you to access programmable features.  When making a selection, only press one button at a time to enter the desired menu.  Once in the desired menu, press and release the preferred setting option until a check mark appears next to the setting, showing that setting has been selected.  Once the setting is complete,", "appears next to the setting, showing that setting has been selected.  Once the setting is complete, press the X button on the touchscreen to close out of the settings screen.  Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or down through the available settings.  Note: Depending on the vehicle\u2019s options, feature settings may vary.  All settings should be changed with the ignition in the ON/RUN position.  UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel.  These buttons allow you to access and change the Customer Programmable Features.  Many features can vary by vehicle.  Buttons on the faceplate are located below and/or beside the Uconnect system in the center of the instrument panel.  In addition, there is a SCROLL/ENTER control knob located on the right side.  Turn the control knob to scroll through menus and change settings.  Push the center of", "right side.  Turn the control knob to scroll through menus and change settings.  Push the center of the control knob one or more times to select or change a setting.  Your Uconnect system may also have SCREEN OFF and MUTE buttons on the faceplate.  Push the SCREEN OFF button on the faceplate to turn off the Uconnect screen.  Push the button again or tap the screen to turn the screen on.  Press the Back Arrow button to exit out of a Menu or certain option on the Uconnect system.", "For the recommended viscosity and quality grades seeThe Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.  For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.  The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.  The following tire grading categories were established by the National Highway Traffic Safety Administration.  The specific grade rating assigned by the tire's manufacturer in each category is shown on the sidewall of the tires on your vehicle.  The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government", "ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction", "traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.  All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.  For devices which are not made a favorite, the device priority is determined by the order in which it was paired.  The most recent device paired will have the higher priority.  Temperature Grades The Temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.  Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.  The grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the", "Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law.  WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.  Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.  Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C.These grades represent the tire's ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.  A tire marked C may have poor traction performance.  WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.", "Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACC Your vehicle may be equipped with the Cruise Control system, or the Adaptive Cruise Control (ACC) system:  Cruise Control can be dangerous where the system cannot maintain a constant speed.  Your vehicle could go too fast for the conditions, and you could lose control and have an accident.  Do not use Cruise Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC)", "traffic or on roads that are winding, icy, snow-covered or slippery.  Adaptive Cruise Control (ACC) increases the driving convenience provided by Cruise Control while traveling on highways and major roadways.  However, it is not a safety system and not designed to prevent collisions.  The Cruise Control function performs differently if your vehicle is not equipped with ACCThis indicator light will illuminate when the cruise control is set to the desired speed  It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information", "in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.", "The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Automatic Dimming Mirror The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.  With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights.  Rotating the dimmer control will also adjust the interior and ambient light levels (e.g.  courtesy lights in the footwell, illuminated cupholders, and front door handles).  Mode Control Turn the mode control knob or press one of the Mode buttons on the touchscreen to adjust airflow distribution.  The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.  Automatic Dimming Mirror \u2014 If Equipped The rearview mirror can", "defrost outlets and demist outlets.  Automatic Dimming Mirror \u2014 If Equipped The rearview mirror can be adjusted up, down, left, and right.  The mirror should be adjusted to center on the view through the rear window.  This mirror automatically adjusts for headlight glare from vehicles behind you.  The Automatic Dimming feature can be turned on or off through the Uconnect Controls button on the touchscreen.  Note: The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver\u2019s rear view.  CAUTION: To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.  Apply the solution onto a clean cloth and wipe the mirror clean.", "Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  The fuel filler cap is located on the driver's side of the vehicle.  If the fuel filler cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle.  If you store quantities of fuel, good maintenance of the stored fuel is also essential.  Fuel contaminated with water will promote the growth of \u201cmicrobes.\u201d These microbes form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the", "form \u201cslime\u201d that will clog the fuel filtration system and lines.  Drain condensation from the supply tank and change the line filter on a regular basis.  Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.  This could result in flash fire causing serious personal injury.  Do not attempt to push or tow your vehicle to get it started.  Vehicles equipped with an automatic transmission cannot be started this way.  Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.  If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.  This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited", "This type of start can be dangerous if done improperly The use of leaded gasoline is prohibited by Federal law.  Using leaded gasoline can impair engine performance and damage the emissions control system.  An out-of-tune engine, certain fuel or ignition malfunctions can cause the catalytic converter to overheat.  If you notice a pungent burning odor or some light smoke, your engine may be out-of-tune or malfunctioning and may require immediate service.  Contact an authorized dealer for service assistance.  The use of fuel additives, which are now being sold as octane enhancers, is not recommended.  Most of these products contain high concentrations of methanol.  Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of The manufacturer and may void or not be covered under the New Vehicle Limited Warranty.  The engine requires the use of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system", "of ultra low sulfur diesel fuel.  Use of incorrect fuel could result in engine and exhaust system damage If climatized or Number 1 ULSD fuel is not available, and you are operating below 20\u00b0F (-6\u00b0C), in sustained arctic conditions, Mopar\u00ae Premium Diesel Fuel Treatment (or equivalent) is recommended to avoid gelling (see Fuel Operating Range Chart).  Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.  Damage to the fuel system or emission control system could result from using an improper fuel filler cap.  A poorly fitting cap could let impurities into the fuel system.  Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system.  To avoid fuel spillage and overfilling, do not \u201ctop off\u201d the fuel tank after filling.  If the vehicle is exposed to extreme cold (below 20\u00b0F or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use", "or -7\u00b0C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel.  This will provide better protection from fuel gelling or wax-plugging of the fuel filters.  Use of biodiesel mixture in excess of 20% can negatively impact the fuel filter's ability to separate water from the fuel, resulting in high pressure fuel system corrosion or damage.  In addition, commercially available fuel additives are not necessary for the proper operation of your diesel engine.  For extreme cold conditions, \"Mopar\u00ae Premium Diesel Fuel Treatment\" is recommended to assist with cold starting.  The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation.  If the indicator light is illuminated, contact an authorized dealer as soon as possible to bleed the system.  If the previously mentioned indicators come on immediately after refueling,", "to bleed the system.  If the previously mentioned indicators come on immediately after refueling, water or AdBlue\u00ae (UREA) have probably been poured into the tank: switch the engine off immediately and contact an authorized dealer.  Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.  Proper maintenance of the engine fuel filter and fuel tank is essential see \"\u21e8draining fuel/water separator filter \u2014 diesel engine\" .", "When any of these situations occur, after all open doors are closed, the FOBIK-Safe search will be executed.  If it detects a Passive Entry key fob inside the vehicle, the vehicle will unlock and alert the customer.  If Passive Entry is disabled using the Uconnect system, the key fob protection described in this section remains active/functional.  When a door is open and the interior lights are on, rotating the instrument panel dimmer control to the extreme bottom position will cause all the interior lights to turn off.  This allows the doors to stay open for extended periods of time without discharging the vehicle\u2019s battery.  Be sure the hood is fully latched before driving your vehicle.  If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.  Failure to follow this warning could result in serious injury or death.  The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not", "order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.  These alerts will not be activated in situations where the vehicle\u2019s engine is left running with the key fob inside.  The Remote Door Lock/Unlock feature provides you the ability to lock or unlock the door on your vehicle without the keys and from virtually any distance.  All occupants must wear seat belts during off-road operation with doors removed.  For information on off-road driving tips, see Do not store detached doors inside of the vehicle, as they may cause personal injury in the event of an accident.  Assistance to remove doors may by required due to the weight of the door to avoid personal injury.  Avoid trapping anyone in a vehicle in a collision.  Remember that the rear doors can only be opened from the outside when the Child-Protection Door Lock system is engaged (locked).  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on", "engaged (locked).  DOOR FRAME \u2014 IF EQUIPPED WITH A SOFT TOP WARNING: Do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide.  This procedure is furnished for use during off-road operation only.  CAUTION: Failure to follow these cautions may cause interior water damage, stains or mildew: Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle's interior.  Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle's interior.  The door frame(s) must be positioned properly to ensure sealing.  Improper installation can cause water to leak into the vehicle's interior.", "It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Access, or allow others to access, information stored in your vehicle systems, including personal information.  When the ACC system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.  Failure to follow these warnings can result in a collision and death or serious personal injury.  Some of the most important safety features in your vehicle are the restraint systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your", "systems: ALWAYS obey traffic laws and pay attention to the road.  ALWAYS drive safely with your hands on the steering wheel.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications when it is safe to do so.  Failure to do so may result in an accident involving serious injury or death.  Always drive safely with your hands on the steering wheel and obey all applicable laws.  You have full responsibility and assume all risks related to the use of the features and applications in this vehicle.  Only use the features and applications in this vehicle when it is safe to do so.  Failure to comply may result in an accident involving in serious injury or death.  ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.  This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles.  It is capable of performing better in a wide", "center of gravity than many passenger vehicles.  It is capable of performing better in a wide variety of off-road applications.  Driven in an unsafe manner, all vehicles can go out of control.  Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.  Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control.  Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury.  Drive carefully.  Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury.  In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually.  In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.  Always buckle up.", "Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change", "The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is", "cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is", "generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the message Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil", "oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.  Oil life reset \u2014 if equipped oil life reset \u2014 if equipped \u00b9 use this qr code to access your digital experience.  Your vehicle may be equipped with an engine oil change indicator system.  The \u201cOil Change Required\u201d message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.  The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style.  Unless reset, this message will continue to display each time you place the ignition in the ON/RUN position.  To turn off the message temporarily, push and release the ok button.  To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure.  SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change", "SCHEDULED SERVICING \u2014 GASOLINE ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, or extremely hot or cold ambient temperatures will influence when the \u201cChange Oil\u201d or \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  On vehicles equipped with an instrument cluster display, \u201cOil Change Required\u201d will be displayed and a single chime will sound, indicating that an oil change is necessary.  On vehicles not equipped with an instrument cluster display, \u201cChange Oil\u201d will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An", "cluster odometer and a single chime will sound, indicating that an oil change is necessary.  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  To reset the system follow the steps described Note: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), 12 months or 350 hours of engine run time, whichever comes first.  The 350 hours of engine run or idle time is generally only a concern for fleet customers.  SCHEDULED SERVICING \u2014 DIESEL ENGINE Your vehicle is equipped with an automatic oil change indicator system.  The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.  Based on engine operation conditions, the oil change indicator message will illuminate.  This means that service is required for your vehicle.  Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d", "tow, extremely hot or cold ambient temperatures will influence when the \u201cOil Change Required\u201d message is displayed.  Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).  An authorized dealer will reset the oil change indicator message after completing the scheduled oil change.  If a scheduled oil change is performed by someone other than an authorized dealer, to reset the messageNote: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or 12 months, whichever comes first.", "Oil Temperature Warning Light This warning light will illuminate to indicate the engine oil temperature is high.  If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.  Wait for oil temperature to return to normal levels.  This warning light will illuminate to indicate the engine oil temperature is high.  If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.  Wait for oil temperature to return to normal levels.  This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the", "dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  If the Low Oil Pressure Warning Light turns on while driving, stop the vehicle and shut down the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the lamp.  If the lamp is still illuminated, shut the engine off, contact an authorized dealer, and do not operate the vehicle until the cause is corrected.  If the lamp is no longer illuminated, the engine can be operated, but should be taken to an authorized dealer as soon as possible for further inspection.  This warning light will illuminate to warn of a high transmission fluid temperature.  This may occur with strenuous usage such as trailer towing.  If this light turns on, stop the vehicle and run the engine at idle or slightly faster, with the transmission in PARK (P) or", "the vehicle and run the engine at idle or slightly faster, with the transmission in PARK (P) or NEUTRAL (N), until the light turns off.  Once the light turns off, you may continue to drive normally.  If Manual transmission equipped, this warning will illuminate to warn of high clutch temperature.  This may occur with driver misuse of clutch pedal or resting foot on the clutch pedal or partially engaging the clutch for longer duration.  If the light turns on, it will be with an additional CLUTCH HOT message.  Stop the vehicle safely and run the engine at idle with transmission gear in NEUTRAL (N) until the light turns off.  Once the light turns off, follow the message displayed in the instrument cluster.  Oil Temperature Warning Light This warning light will illuminate to indicate the engine oil temperature is high.  If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.  Wait for oil temperature to return to normal levels.  Oil Pressure Warning Light This warning", "Wait for oil temperature to return to normal levels.  Oil Pressure Warning Light This warning light will illuminate, and a chime will sound, to indicate low engine oil pressure.  If the light and chime turn on while driving, safely stop the vehicle and turn off the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the Oil Pressure Warning Light.  If the Oil Pressure Warning Light is still illuminated, turn the engine OFF and contact an authorized dealer for further assistance.  Do not operate the vehicle until the cause is corrected.  If the light is no longer illuminated, the engine can be operated but it is recommended to take the vehicle to an authorized dealer as soon as possible.  Do not operate the vehicle until the cause is corrected.  This light does not indicate how much oil is in the engine.  The engine oil level must be checked under the hood.  Do Not Operate The Engine With Low Oil Pressure If the Low Oil Pressure Warning Light turns on while", "Not Operate The Engine With Low Oil Pressure If the Low Oil Pressure Warning Light turns on while driving, stop the vehicle and shut down the engine as soon as possible.  After the vehicle is safely stopped, restart the engine and monitor the lamp.  If the lamp is still illuminated, shut the engine off, contact an authorized dealer, and do not operate the vehicle until the cause is corrected.  If the lamp is no longer illuminated, the engine can be operated, but should be taken to an authorized dealer as soon as possible for further inspection.  Note: Do not operate the vehicle until the cause is corrected.  This light does not show how much oil is in the engine.  The engine oil level must be checked under the hood.  CAUTION: If oil pressure falls to less than normal readings, shut the engine off immediately.  Failure to do so could result in immediate and severe engine damage.", "To Arm The System Follow these steps to arm the Vehicle Security system: Make sure the vehicle\u2019s ignition is placed in the OFF position.  Perform one of the following methods to lock the vehicle: push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zonePush the lock button on the key fob.  If any doors are open, close them.  Note: The Vehicle Security system will not arm if you lock the doors using the manual door lock.  To Arm The System Follow these steps to arm the Vehicle Security system: Make sure the vehicle\u2019s ignition is placed in the OFF position.  Perform one of the following methods to lock the vehicle: push the lock button on the interior power door lock switch with the driver and/or passenger door open.  Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone Push the", "Passive Entry door handle with a valid key fob available in the same exterior zone Push the lock button on the key fob.  If any doors are open, close them.  Note: The Vehicle Security system will not arm if you lock the doors using the manual door lock.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.  SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine.  The system does not need to be armed or activated.  Operation is automatic,", "disabling the engine.  The system does not need to be armed or activated.  Operation is automatic, regardless of whether the vehicle is locked or unlocked.  The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation.  Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle.  The system cannot reprogram a key fob obtained from another vehicle.  After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check.  If the light remains on after the bulb check, it indicates that there is a problem with the electronics.  In addition, if the light begins to flash after the bulb check, it indicates that someone attempted to start the engine with an invalid key fob.  In the event that a valid key fob is used to start the engine but there is an issue with the vehicle electronics, the engine will start and shut off after two", "but there is an issue with the vehicle electronics, the engine will start and shut off after two seconds.  If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics.  Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.  All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics CAUTION: The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.  Use of these systems may result in vehicle starting problems and loss of security protection.  Note: A key fob that has not been programmed is also considered an invalid key.  To Disarm The System The Vehicle Security system can be disarmed using any of the following methods: Push the unlock button on the key fob.  Grab the Passive Entry door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle", "door handle (if equipped) Cycle the vehicle ignition system out of the OFF position.  The Vehicle Security system is designed to protect your vehicle.  However, you can create conditions where the system will give you a false alarm.  If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether you are in the vehicle or not.  If you remain in the vehicle and open a door, the alarm will sound.  If this occurs, disarm the Vehicle Security system.  If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound.  If this occurs, disarm the Vehicle Security system.  Note: The driver's door key cylinder cannot arm or disarm the Vehicle Security system.  When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped", "power door lock switches will not unlock the doors.  Vehicle Security Warning Light \u2014 If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.  Rearming Of The System If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.", "Shifting Fully press the clutch pedal before shifting gears.  As you release the clutch pedal, lightly press the accelerator pedal.  You should always use FIRST gear when starting from a standing position.  Note: A certain amount of noise from the transmission is normal.  This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving.  The noise may also be more noticeable when the transmission is warm.  This noise is normal and is not an indication of a problem with your clutch or transmission.  Automatic Transmission \u2014 If Equipped  Transmission function is monitored electronically for abnormal conditions.  If a condition is detected that could result in transmission damage, Transmission Limp Home mode is activated.  In this mode, the transmission may operate only in certain gears, or may not shift at all.  Vehicle performance may be severely degraded and the engine may stall.  In some situations, the", "Vehicle performance may be severely degraded and the engine may stall.  In some situations, the transmission may not re-engage if the engine is turned off and restarted.  The Malfunction Indicator Light (MIL) may be illuminated.  A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary.  It is important to use the proper transmission fluid to ensure optimum transmission performance and life.  Use only manufacturer's specified transmission fluid It is important to maintain the transmission fluid at the correct level using the recommended fluid.  Using a transmission fluid other than manufacturer\u2019s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or", "failure.  If you continue to operate the vehicle when the CLUTCH HOT message is displayed or Transmission Temperature Warning Light is illuminated, you could cause the clutch to overheat and cause severe clutch damage, transmission damage or failure.  Using a lower gear while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  This action will also provide better engine braking.  Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.  For Recreational Towing For Towing A Disabled Vehicle When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing a heavy trailer), use the AutoStick shift control to select a lower gear Under these conditions, using a lower gear will improve performance and extend transmission", "gear Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat build-up.  Racing the engine or spinning the wheels may lead to transmission overheating and failure.  Allow the engine to idle with the transmission in NEUTRAL (N) for at least one minute after every five rocking-motion cycles.  This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.  When \u201crocking\u201d a stuck vehicle by shifting between DRIVE/SECOND gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.  Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.  It can also damage the tires.  Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).  During cold weather, you may experience increased effort in shifting until the transmission fluid warms up.  This", "you may experience increased effort in shifting until the transmission fluid warms up.  This is normal.  Routine fluid and filter changes are not required.  However, change the fluid and filter if the fluid becomes contaminated (with water, etc.  ), or if the transmission is disassembled for any reason.", "The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the ABS activates: If the ABS Warning Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.  If the ABS Warning Light does not come on when the ignition is placed in the ON/RUN mode, have the light repaired as soon as possible.  This warning light monitors the ABS.  The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds.  The yellow ABS Warning Light will turn on when the ignition is placed in the ON/RUN mode and may stay on for as long as four seconds.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force", "equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of", "maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.  The BAS is designed to optimize the vehicle\u2019s braking capability during emergency braking maneuvers.  The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure", "situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes.  This can help reduce braking distances.  The BAS complements the Anti-Lock Brake System (ABS) by applying the brakes very quickly, creating the most efficient braking assistance possible.  To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not \u201cpump\u201d the brakes).  Do not reduce brake pedal pressure unless braking is no longer desired.  Once the brake pedal is released, the BAS is deactivated.  Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD).  In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.  Immediate repair to the ABS system is required.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose", "are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  If the ABS Warning Light remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.  However, the conventional brake system will continue to operate normally if the ABS Warning Light is on.  The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting", "may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of", "in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.  The ABS is designed to function with the Original Equipment Manufacturer (OEM) tires.  Modification may result in degraded ABS performance.  Your vehicle is equipped with an advanced Electronic Brake Control (EBC) system.  This system includes Anti-Lock Brake System (ABS), Brake Assist System (BAS), Electronic Brake Force Distribution (EBD), Electronic Roll Mitigation (ERM), Electronic Stability Control (ESC), Hill Start Assist (HSA), and Traction Control System (TCS).  These systems work together to enhance both vehicle stability and control in various driving conditions.  Anti-Lock Brake System (ABS) The ABS provides increased vehicle stability and brake performance under most braking conditions.  The system automatically prevents wheel lock and enhances vehicle control during braking.  The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started and driven.", "cycle to ensure that the ABS is working properly each time the vehicle is started and driven.  During this self-check, you may hear a slight clicking sound, as well as some related motor noises.  The ABS is activated during braking when the system detects one or more wheels are beginning to lock.  Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s).  You also may experience the following normal characteristics when the abs activates: abs motor noise or clicking sounds (you may continue to hear for a short time after the stop) brake pedal pulsations a slight drop of the brake pedal at the end of the stop note: the abs is designed to function with the original equipment manufacturer (oem) tires.  Modification may result in degraded ABS performance.  WARNING: The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting", "may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.  This interference can cause possible loss of anti-lock braking capability.  Installation of such equipment should be performed by qualified professionals.  Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.  Pumping makes the stopping distance longer.  Just press firmly on your brake pedal when you need to slow down or stop.  The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.  The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.  The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of", "in a reckless or dangerous manner that could jeopardize the user\u2019s safety or the safety of others.", "TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  Towing Service Our towing service gives you peace of mind and confidence.  If your vehicle becomes disabled as a result of a mechanical breakdown, Roadside Assistance will dispatch a towing service to transport your vehicle to the closest authorized Chrysler, Dodge, Jeep\u00ae, or Ram dealer.  If you choose to go to another dealer, you will be responsible for the cost if the extra distance exceeds 10 miles.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles", "a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension", "may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Towing Tips Before towing, practice turning, stopping and backing the trailer in an area away from heavy traffic.  If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.  TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.  Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.  To maintain the New Vehicle Limited Warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.  TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.  If the transmission and drivetrain are operable, disabled", "using a commercial towing service.  If the transmission and drivetrain are operable, disabled vehicles may also be towed as described on Proper towing or lifting equipment is required to prevent damage to your vehicle.  Use only tow bars and other equipment designed for this purpose, following equipment manufacturer\u2019s instructions.  Use of safety chains is mandatory.  Attach a tow bar or other towing device to main structural members of the vehicle, not to fascia/bumpers or associated brackets.  State and local laws regarding vehicles under tow must be observed.  If you must use the accessories (wipers, defrosters, etc.)  while being towed, the ignition must be in the ON/RUN position, not the ACC position.  If the vehicle's battery is discharged, instructions on shifting the automatic transmission out of PARK (P) in order to move the vehicle CAUTION: Do not use sling type equipment when towing.  Vehicle damage may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension", "may occur.  When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components.  Damage to your vehicle may result from improper towing.  Recreational Towing \u2014 Four-Wheel Drive Models Note: The transfer case must be shifted into N (Neutral), automatic transmission must be in PARK, and manual transmission must be in gear (NOT in NEUTRAL) for recreational towing.  CAUTION: DO NOT dolly tow any 4WD vehicle.  Towing with only one set of wheels on the ground (front or rear) will cause severe transmission and/or transfer case damage.  Tow with all four wheels either ON the ground, or OFF the ground (using a vehicle trailer).  Tow only in the forward direction.  Towing this vehicle backwards can cause severe damage to the transfer case.  Automatic transmissions must be placed in PARK for recreational towing.  Manual transmissions must be placed in gear (not in Neutral) for recreational towing.  Before recreational towing, perform the procedure outlined under \u201cShifting Into N", "towing.  Before recreational towing, perform the procedure outlined under \u201cShifting Into N (Neutral)\u201d to be certain that the transfer case is fully in N (Neutral).  Otherwise, internal damage will result.  Towing this vehicle in violation of the previously listed requirements can cause severe transmission and/or transfer case damage.  Damage from improper towing is not covered under the New Vehicle Limited Warranty.  Do not use a bumper-mounted clamp-on tow bar on your vehicle.  The bumper face bar will be damaged.", "The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If", "if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.  Engine start-up in very low ambient temperature could result in evident white smoke.  This condition will disappear as the engine warms up.  During extremely cold temperatures (-22\u00b0F [-30\u00b0C] or below), transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.", "may be modified depending on engine and transmission temperature as well as vehicle speed.  Normal operation will resume once the transmission temperature has risen to a suitable level.  The voltmeter may show a gauge fluctuation at various engine temperatures.  This is caused by the glow plug heating system.  The number of cycles and the length of the cycling operation is controlled by the engine control module.  Glow plug heater operation can run for several minutes.  Once the heater operation is complete the voltmeter needle will stabilize.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or", "will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the", "when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the", "with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  All message center lights are off.  Malfunction Indicator Light (MIL) is off.  Engine Oil Pressure telltale is not illuminated.  Voltmeter operation.  Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.  Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000).  Do not operate the engine with the tachometer pointer in the red area.  Engine damage will occur.  Temperature Gauge The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It", "a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Instrument Cluster Display The instrument cluster display features a driver interactive display Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel", "is in the ON/RUN position.  The fuel pump symbol points to the side of the vehicle where the fuel filler door is located Speedometer Indicates vehicle speed.  The temperature gauge shows engine coolant temperature.  Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.  The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.  It should not be allowed to exceed the upper limits of the normal operating range.  A hot engine cooling system is dangerous.  You or others could be badly burned by steam or boiling coolant.  It is recommended that you call an authorized dealer for service if your vehicle overheats.  Driving with a hot engine cooling system could damage your vehicle.  If the temperature gauge reads \u201cH\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d,", "turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d, turn the engine off immediately and call an authorized dealer for service.  Driving with a hot cooling system could damage your vehicle.  If the temperature gauge reads \u201cH,\u201d pull over and stop the vehicle.  Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.  If the pointer remains on the \u201cH\u201d and you hear continuous chimes, turn the engine off immediately and call for service.  This warning light warns of an overheated engine condition.  If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound.  If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first.", "Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201dWARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING:", "Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  Connected Vehicles Privacy of any wireless and wired communications cannot be assured.  Third parties may unlawfully intercept information and private communications without your consent.  For further information, refer to \u201cData Collection & Privacy\u201d in your Uconnect Radio Instruction Manual or \u201cOnboard Diagnostic System (OBD II) Cybersecurity\u201d WARNING: It is not possible to know or to predict all of the possible outcomes if your vehicle\u2019s systems are breached.  It may be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may", "safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death.  CYBERSECURITY Depending on applicability, your vehicle may be able to send or receive information from a wired or wireless network.  This information allows systems and features in your vehicle to function properly.  Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful access to vehicle systems and wireless communications.  Vehicle software technology continues to evolve over time and FCA US LLC, working with its suppliers, evaluates and takes appropriate steps as needed.  As always, if you experience unusual behavior, contact an authorized dealer immediately, \"\u21e8if you need assistance\" , or refer to your uconnect radio instruction manual for additional contact information.  The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle", "unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as Uconnect software) is installed.  WARNING: ONLY insert trusted media devices/components into your vehicle.  Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached.  As always, if you experience unusual vehicle behavior, contact an authorized dealer immediately.  Note: to help further improve user experience, features, stability, etc., and minimize the potential risk of a security breach, vehicle owners should routinely check www.driveuconnect.com (us residents) or www.driveuconnect.ca (canadian residents) to learn about available uconnect software updates.  VEHICLE SECURITY SYSTEM \u2014 IF EQUIPPED The Vehicle Security system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation.  When the system is activated, the interior switches for", "switch for unauthorized operation.  When the system is activated, the interior switches for door locks are disabled.  The Vehicle Security system provides both audible and visible signals.  If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals: the horn will pulse, the parking lights and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash."]
\ No newline at end of file