Datasets:

ramixpe
/

adjusted_dataset

+text
+"<｜begin▁of▁sentence｜>
+### Instruction:
+XLNC-4-FAILED_TO_CREATE_NNS
+### Response:
+(Severity: 4), (Category: INFRA), (Description: XLNCd mirrors VRFs into linux by creating network namespaces. The creation of a NNS has failed, and so the linux network namespaces are out of sync with the XR vrf configuration.), (Recommended Action: Replay the VRF configuration that caused the syslog. If the same error is seen, restart the XLNCd process. If the problem persists through process restarts, If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)
+<|EOT|>
+"
+"<｜begin▁of▁sentence｜>
+### Instruction:
+EDRM_DLL-3-ADD_NPU
+### Response:
+(Severity: 3), (Category: L2), (Description: Addition of the NP instance failed due to the reason indicated.), (Recommended Action: None. The NP addition will be retried automatically.)
+<|EOT|>
+"
+"<｜begin▁of▁sentence｜>
+### Instruction:
+ENVMON-4-SAT_SPEED_DUP_UPGRADE
+### Response:
+(Severity: 4), (Category: PLATFORM), (Description: This is a notification to user that the speed / duplex parameters of a particular port set to auto negotiate has upgraded post negotiation from its minimum capability due to either higher capability of the peer or the the peer not able to engage in auto negotiation.), (Recommended Action: This might require some manual config changes for other dependent features such as Sat QoS.)
+<|EOT|>
+"
+"<｜begin▁of▁sentence｜>
+### Instruction:
+BCDL2-6-MSG_GENERIC_ERROR
+### Response:
+(Severity: 6), (Category: OS), (Description: BCLS process has hit some error condition.), (Recommended Action: Contact support.)
+<|EOT|>
+"
+"<｜begin▁of▁sentence｜>
+### Instruction:
+CLKCTRL_T-2-EEPROM_OVERCURRENT
+### Response:
+(Severity: 2), (Category: PLATFORM), (Description: ClkCtrl detected an EEPROM overcurrent condition), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)
+<|EOT|>
+"
+"<｜begin▁of▁sentence｜>
+### Instruction:
+LIB_VMAN-3-SET_VTX_ROMVAR_SPACE
+### Response:
+(Severity: 3), (Category: OS), (Description: Failed to set ENABLE_VTX ROM monitor variable due to no space in Monitor Variable Table.), (Recommended Action: Verify number of entries in Monitor Variable Table.)
+<|EOT|>
+"
+"<｜begin▁of▁sentence｜>
+### Instruction:
+QSFP_PLUS-2-LANE_3_HIGH_RX_POWER_ALARM
+### Response:
+(Severity: 2), (Category: PLATFORM), (Description: Environmental monitoring has detected a QSFP+ Rx power greater than or equal to the high Rx power alarm threshold. The QSFP+ is the pluggable optics on the line cards. The Rx power threshold values are read from the QSFP+.), (Recommended Action: Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. Replace the attenuator with working one (if any) to isolate bad attenuator. Replace the optics with working one (if any) to isolate bad optics. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands 'show tech-support ethernet interface location <loc>', 'show hw-module fpd location all' and 'admin show inventory'.)
+<|EOT|>
+"
+"<｜begin▁of▁sentence｜>
+### Instruction:
+JACKET-3-CPU_CTRL_REG_ACCESS
+### Response:
+(Severity: 3), (Category: L2), (Description: Unable to read/write to a CPU Ctrl register.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Copy the error message exactly as it appears on the console or in the system log. Issue the <CmdBold>show controllers CPUCtrl ltrace <><noCmdBold> command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the <CmdBold>show controllers CPUCtrl ltrace <><noCmdBold> output, call your Cisco technical support representative and provide the representative with the gathered information.)
+<|EOT|>
+"
+"<｜begin▁of▁sentence｜>
+### Instruction:
+SPA_ETHER-2-SPA_JKT_ERR
+### Response:
+(Severity: 2), (Category: L2), (Description: The Jacket driver failed to parse spa driver argument.), (Recommended Action: --)
+<|EOT|>
+"