title: Rectangular Waveguide HOM Couplers for a TESLA Superstructure

abstract: Some modifications of a Rectangular Waveguide HOM couplers for TESLA superstructure have been investigated. These RWG HOM couplers are to be installed between the cavities of the superstructure and also at the both ends of it. We investigated a RWG HOM coupler attached to the beam pipe through the slots orientated along beam pipe axis (longitudinal slots), perpendicular to it (azimutal slots) and at some angle to this axis. For dipole modes of both polarizations damping two RWG in every design were used. This paper presents the results obtained for scaled-up setup at 3 GHz at room temperature. The advantages of HOM coupler with longitudinal slots for damping dipole modes and compact HOM coupler with slots at some angle to the axis are shown. Arrangement of HOM coupler in cryostat and heating due to HOM and FM losses are presented. Calculations and design of the feeding RWG coupler for superstructure are also presented.


title: Circular photogalvanic effect induced by monopolar spin orientation in p-GaAs/AlGaAs MQW

abstract: The circular photogalvanic effect (CPGE) has been observed in (100)-oriented $p$-GaAs/AlGaAs quantum wells at normal incidence of far-infrared radiation. It is shown that monopolar optical spin orientation of free carriers causes an electric current which reverses its direction upon changing from left to right circularly polarized radiation. CPGE at normal incidence and the occurence of the linear photogalvanic effect indicate a reduced point symmetry of studied multi-layered heterostructures. As proposed, CPGE can be utilized to investigate separately spin polarization of electrons and holes and the symmetry of quantum wells.


title: Two large-area anode-pad MICROMEGAS chambers as the basic elements of a pre-shower detector

abstract: The design of a detector based on MICROMEGAS (MICRO MEsh GAseous Structure) technology is presented. Our detector is characterized by a large active area of 398(\times)281 mm(^{2}), a pad read-out with 20(\times)22 mm(^{2}) segmentation, and an uniform amplification gap obtained by insulating spacers (100 (\mu)m high and 200 (\mu)m in diameter). The performances of several prototypes have been evaluated under irradiation with secondary beams of 2 GeV/c momentum charged pions and electrons. We consider such a detector as the basic element for a pre-shower detector to equip the PHOton Spectrometer (PHOS) of the ALICE experiment. Its assets are modularity, small amount of material, robustness and low cost.


title: Acceleration for the mu-Storage Ring Neutrino Source

abstract: A muon storage ring neutrino source uses an induction linac for muon capture, a 200 MHz copper cavity system for cooling, and 200 and 400 MHz superconducting rf systems for acceleration to a final energy of up to 50 GeV. These systems and their requirements are discussed in this paper.


title: A Fast Switchyard for the TESLA FEL-Beam Using a Superconducting Transverse Mode Cavity

abstract: In the present design of the TESLA Linear Collider with integrated X-ray Laser Facility it is necessary that 1 ms long bunch trains with about 10000 bunches are generated and distributed to several free electron laser (FEL) beam lines. The different scientific applications of the X-ray FELs need specific filling patterns of the bunches in the bunch train. It is shown that a fast switch-yard based on a superconducting transverse mode cavity can be used to generate the required bunch pattern in a flexible way while keeping the beam loading in the main linear accelerator constant. The conceptual design of the beam optics and the transverse mode cavity are presented.


title: On electromagnetic induction

abstract: A general law for electromagnetic induction phenomena is derived from Lorentz force and Maxwell equation connecting electric field and time variation of magnetic field. The derivation provides with a unified mathematical treatment the statement according to which electromagnetic induction is the product of two independent phenomena: time variation of magnetic field and effects of magnetic field on moving charges. The general law deals easily-without ad hoc assumptions-with typical cases usually considered as exceptions to the flux rule and contains the flux rule as a particular case.


title: Quadrupole Misalignments and Steering in Long Linacs

abstract: We present a study of orbit jitter and emittance growth in a long linac caused by misalignment of quadrupoles. First, assuming a FODO lattice, we derive analytical formulae for the RMS deviation of the orbit and the emittance growth caused by random uncorrelated misalignments of all quadrupoles. We then consider an alignment algorithm based on minimization of BPM readings with a given BPM resolution and finite mover steps.


title: Suppression of beam breakup instability in a long train by introducing energy spread between the bunches

abstract: Interaction between the bunches in the NLC main linac via long range wakefields can cause a beam breakup instability. Although the magnitude of the long range wakefields for an ideal NLC structure is below the instability threshold, the wake increases when structure manufacturing errors are taken into account. In case of large errors, the developing instability can result in the projected emittance dilution of the bunch train. To suppress the instability, we propose to introduce an energy spread between the bunches, similar to the BNS energy spread for damping of the beam breakup within a single bunch. Based on simple estimates, we show that the energy spread of order of 1-2% should be enough for suppression of the instability. The results of computer simulations with the simulation code LIAR confirm theoretical estimates and indicate that both the tolerances for structure misalignments and the incoming beam jitter can be considerably loosened by introducing the energy spread within the beam.


title: Numerical Analysis of a Beam-Energy-Spread Monitor Using Multi-Stripline Electrodes

abstract: A beam-energy-spread monitor is under development in order to control and stabilize the energy spread of high-current single-bunch electron beams for producing a sufficient number of positrons. The author has proposed a new monitor using multi-stripline electrodes in order to reinforce this purpose. This report describes the basic design of the monitor based on a numerical analysis. The analysis result shows that the resolution of an energy-spread measurement is expected to be less than 0.3% for nominal operation conditions.


title: Universal quantification for deterministic chaos in dynamical systems

abstract: A cell dynamical system model for deterministic chaos enables precise quantification of the round-off error growth,i.e., deterministic chaos in digital computer realizations of mathematical models of continuum dynamical systems. The model predicts the following: (a) The phase space trajectory (strange attractor) when resolved as a function of the computer accuracy has intrinsic logarithmic spiral curvature with the quasiperiodic Penrose tiling pattern for the internal structure. (b) The universal constant for deterministic chaos is identified as the steady-state fractional round-off error k for each computational step and is equal to 1 /sqr(tau) (=0.382) where tau is the golden mean. (c) The Feigenbaum's universal constants a and d are functions of k and, further, the expression 2(a**2) = (pie)*d quantifies the steady-state ordered emergence of the fractal geometry of the strange attractor. (d) The power spectra of chaotic dynamical systems follow the universal and unique inverse power law form of the statistical normal distribution.


title: A Variational Approach in the Dissipative Nonlinear Schr\"{o}dinger Equation

abstract: The properties of pulse propagation in a nonlinear fiber including linear damped term added in the usual nonlinear Schr\"odinger equation is analyzed analytically. We apply variational modified approach based on the lagrangian that describe the dynamic of system and with a trial function we obtain a solution which is more accuracy when compared with a pertubative solution. As a result, the problem of pulse propagation in a fiber with loss can be described in good agreement with exact results.


title: The interpretations by experimenters of experiments on 'time dilation': 1940-1970 circa

abstract: Experimental tests on `time dilation' began in 1938 with Ives and Stilwell's work of the transverse Doppler effect due to atoms in inertial flight. Rossi and Hall (1941) inaugurated the era of fast moving elementary particles that dominated the scene until the discovery of the Mossbauer effect (1957). This discovery suggested the use of photons emitted without recoil in crystalline solids for testing both time dilation and gravitational red shift. Finally, around 1970, Hafele and Keating dealt again with time dilation by sending macroscopic atomic clocks around the Earth. The interpretations of these experiments by experimenters have been characterized by the use of additional hypotheses not necessary for the formal development of the theories under test (the idea that all clocks measure proper time) or hypotheses completely extraneous to the theories themselves (the idea that atoms are clocks). If these assumptions are dropped, it turns out that the only experiments concerning time dilation are those performed with elementary particles in inertial flight. The historical and epistemological implications are discussed.


title: Negative Group Velocity

abstract: The group velocity for pulses in an optical medium can be negative at frequencies between those of a pair of laser-pumped spectral lines. The gain medium then can amplify the leading edge of a pulse resulting in a time advance of the pulse when it exits the medium, as has been recently demonstrated in the laboratory. This effect has been called superluminal, but, as a classical analysis shows, it cannot result in signal propgation at speeds greater than that of light in vacuum.


title: Energy Absorber R&D

abstract: We describe the program of research and development being undertaken by a consortium of Illinois university groups to develop liquid-hydrogen energy absorbers for muon-beam cooling for a possible stored-muon-beam neutrino factory.


title: Multipactoring Code for 3D Accelerating Structures

abstract: The simulation code has been developed to investigate possible electron multi- pacting in the 3D RF cavities using preliminary calculated field components. The code provides different options of numerical study of the electron multi- pacting including search of the resonant trajectories and simulation of an electron multiplication.


title: Heart Rate Variability: Measures and Models

abstract: We focus on various measures of the fluctuations of the sequence of intervals between beats of the human heart, and how such fluctuations can be used to assess the presence or likelihood of cardiovascular disease. We examine sixteen such measures and their suitability for correctly classifying heartbeat records of various lengths as normal or revealing the presence of cardiac dysfunction, particularly congestive heart failure. Using receiver-operating-characteristic analysis we demonstrate that scale-dependent measures prove substantially superior to scale-independent ones. The wavelet-transform standard deviation at a scale near 32 heartbeat intervals, and its spectral counterpart near 1/32 cycles/interval, turn out to provide reliable results using heartbeat records just minutes long. We further establish for all subjects that the human heartbeat has an underlying stochastic origin rather than arising from a chaotic attractor. Finally, we develop a mathematical point process that emulates the human heartbeat time series for both normal subjects and heart-failure patients.

categories: physics.bio-ph nlin.CD physics.data-an physics.med-ph q-bio.QM q-bio.TO


title: Inelastic Collisions of Ultracold Polar Molecules

abstract: The collisional stability of ultracold polar molecules in electrostatic traps is considered. Rate constants for collisions that drive molecules from weak-field-seeking to strong-field-seeking states are estimated using a simple model. The rates are found to be quite large, of order 10^{-12} - 10^{-10} cm^3/sec, and moreover to grow rapidly in an externally applied electric field. It is argued that these results are generic for polar molecules, and that therefore polar molecules should be trapped by other than electrostatic means.


title: Recent Advances in Electron and Positron Sources

abstract: Recent advances in electron and positron sources have resulted in new capabilities driven in most cases by the increasing demands of advanced accelerating systems. Electron sources for brighter beams and for high average-current beams are described. The status and remaining challenges for polarized electron beams are also discussed. For positron sources, recent activity in the development of polarized positron beams for future colliders is reviewed. Finally, a new proposal for combining laser cooling with beam polarization is presented.


title: Four-wave mixing at maximum coherence and eliminated Doppler broadening controlled with the driving fields

abstract: New feasibity of coherent quantum control of four-wave mixing processes in a resonant Doppler-broadened medium are studied. We propose a technique which enables one to enhance the quantum efficiency of nonlinear optical conversion. At the same time, it allows one to decrease the required intensities of the fundamental beams compared to those necessary in the approach based on coherent population trapping. The major outcomes of the analysis are illustrated with numerical simulation addressed within a practical medium.


title: IHEP Experience on Creation and Operation of RFQS

abstract: The new 1.8 MeV proton RFQ was completed and started operation in the IHEP in 1997. It was built according to the plan of modernization of the injection system to the booster of the IHEP proton synchrotron.


title: Ienversionless gain in an optically-dense resonant Doppler-broadened medium

abstract: Resonant nonlinear-optical interference processes in four-level Doppler-broadened media are studied. Specific features of amplification and optical switching of short-wavelength radiation in a strongly-absorbing resonant gas under coherent quantum control with two longer wavelength radiations, are investigated. The major outcomes are illustrated with virtual experiments aimed at inversionless short-wavelength amplification, which also address deficiencies in this regard in recent experiments. With numerical simulations related to the proposed experiment in optically-dense sodium dimer vapor, we show optimal condition for optical switching and the expected gain of the probe radiation, which is above the oscillation threshold.


title: New Tasks and New Codes for RFQ Beam Simulation

abstract: Proton linear accelerator is the base Accelerator Driven Power System (ADS). Such ADS are dedicated to various purposes: weapon plutonium conversion, "energy amplifier", transmutation of radionuclear wastes etc. Solution of these tasks requires proton beams with energy 1 GeV and average current up to 30 mA. At the moment there are no problems of fundamental nature in such linac construction. The main problems have economic and technical aspects. Problems of CW linac will be demonstrated on the base beam dynamics requirements. New code package LIDOS.RFQ.Designer makes possible to simulate beam dynamics in RF fields of real vane shape (including gaps between RFQ section) as well as to determine channel parameters tolerances for reliable operation


title: RFQ Parameter Choice by Multi-Parameter Optimization

abstract: Experts in different accelerator laboratories accumulated wide experience in RFQ designing. Nevertheless new tasks on high-power, high-energy CW linac designing (for example, for ADT applications) were appeared recently. Such accelerators must be practically free of beam losses. This main condition placed more stringent requirements upon beam quality at the input of each linac part. Because RFQ is used as beginning part in above accelerators beam high-quality requirements is related to RFQ primarily. It means that existing experience in RFQ designing must be enriching by new approaches and new methodology


title: Measurements of RF Cavity Voltages by X-ray Spectrum Measurements

abstract: Measurement of the endpoints of X-ray spectra emitted from RF cavities is a useful non-invasive technique for measuring peak voltages within the cavities. The matching of calculated X-ray spectra to measured spectra is described, with emphasis upon the endpoint region.


title: The "W" Particle and the Weak Force Mechanism

abstract: A transformation mechanism is proposed for the "W" weak force IVB particle. The W is a dense "metric" boson which catalyzes transformations by combining reactants with virtual particle-antiparticle pairs created from the virtual vacuum particle-antiparticle "sea". "W" and "Z" IVB mass functions to recreate the original ("Big Bang") metric energy and density (the "electroweak" force unification era or symmetric energy state) in which elementary particles were first formed and transformed, thereby maintaining the invariance of charge and other conserved parameters of elementary particles in the contemporary universe. Common weak force decays of leptons, mesons, and baryons are illustrated. A single electromagnetic transformation is also considered. A table of three IVB "families" and associated Higgs bosons is appended, illustrating the (hypothetical) higher-energy structure and cosmological role of the weak force.


title: Longitudinal Laser Shaping in Laser Wakefield Accelerators

abstract: We study the energetics of wake excitation during the laser-plasma interaction in application to laser wakefield accelerators. We find that both the wake amplitude and the accelerating efficiency (transformer ratio) can be maximized by properly shaping the longitudinal profile of the driving laser pulse. The corresponding family of laser pulse shapes is derived in the nonlinear regime of laser-plasma interaction. Such shapes provide theoretical upper limit on the magnitude of the wakefield and efficiency by allowing for uniform photon deceleration inside the laser pulse. We also construct realistic optimal pulse shapes that can be produced in finite-bandwidth laser systems.


title: Laser Shaping and Optimization of the Laser-Plasma Interaction

abstract: The physics of energy transfer between the laser and the plasma in laser wakefield accelerators is studied. We find that wake excitation by arbitrary laser shapes can be parameterized using the total pulse energy and pulse depletion length. A technique for determining laser profiles that produce the required plasma excitation is developed. We show that by properly shaping the longitudinal profile of the driving laser pulse, it is possible to maximize both the transformer ratio and the wake amplitude, achieving optimal laser-plasma coupling. The corresponding family of laser pulse shapes is derived in the nonlinear regime of laser-plasma interaction. Such shapes provide theoretical upper limit on the magnitude of the wakefield and efficiency of the accelerating stage by allowing for uniform photon deceleration inside the laser pulse. We also construct realistic optimal pulse shapes that can be produced in finite-bandwidth laser systems and propose a two-pulse wake amplification scheme using the optimal solution.


title: Spatial coherence of thermal near fields

abstract: We analyze the spatial coherence of the electromagnetic field emitted by a half-space at temperature T close to the interface. An asymptotic analysis allows to identify three different contributions to the cross-spectral density tensor in the near-field regime. It is shown that the coherence length can be either much larger or much shorter than the wavelength depending on the dominant contribution.


title: Discrete solvent effects on the effective interaction between charged colloids

abstract: Using computer simulations of two charged colloidal spheres with their counterions in a hard sphere solvent, we show that the granular nature of the solvent significantly influences the effective colloidal interaction. For divalent counterions, the total effective force can become attractive generated by counterion hydration, while for monovalent counterions the forces are repulsive and well-described by a solvent-induced colloidal charge renormalization. Both effects are not contained in the traditional "primitive" approaches but can be accounted for in a solvent-averaged primitive model.


title: RBF neural net based classifier for the AIRIX accelerator fault diagnosis

abstract: The AIRIX facility is a high current linear accelerator (2-3.5kA) used for flash-radiography at the CEA of Moronvilliers France. The general background of this study is the diagnosis and the predictive maintenance of AIRIX. We will present a tool for fault diagnosis and monitoring based on pattern recognition using artificial neural network. Parameters extracted from the signals recorded on each shot are used to define a vector to be classified. The principal component analysis permits us to select the most pertinent information and reduce the redundancy. A three layer Radial Basis Function (RBF) neural network is used to classify the states of the accelerator. We initialize the network by applying an unsupervised fuzzy technique to the training base. This allows us to determine the number of clusters and real classes, which define the number of cells on the hidden and output layers of the network. The weights between the hidden and the output layers, realising the non-convex union of the clusters, are determined by a least square method. Membership and ambiguity rejection enable the network to learn unknown failures, and to monitor accelerator operations to predict future failures. We will present the first results obtained on the injector.


title: Theory and Suppression of Multibunch Beam Breakup in Linear Colliders

abstract: We recently developed an analytic theory of cumulative multibunch beam breakup that includes a linear variation of transverse focusing across the bunch train. The focusing variation saturates the exponential growth of the beam breakup and establishes an algebraic decay of the transverse bunch displacement versus bunch number. In this paper we illustrate how the focusing variation works to suppress multibunch beam breakup, as well as how the mechanism scales with accelerator and beam parameters.


title: Driver Accelerator Design for the 10 kW Upgrade of the Jefferson Lab IR FEL

abstract: An upgrade of the Jefferson Lab IR FEL is now under construction. It will provide 10 kW output light power in a wavelength range of 2-10 microns. The FEL will be driven by a modest-sized 80-210 MeV, 10 mA energy-recovering superconducting RF (SRF) linac. Stringent phase space requirements at the wiggler, low beam energy, and high beam current subject the design to numerous constraints. These are imposed by the need for both transverse and longitudinal phase space management, the potential impact of collective phenomena (space charge, wakefields, beam break-up (BBU), and coherent synchrotron radiation (CSR)), and interactions between the FEL and the accelerator RF system. This report addresses these issues and presents an accelerator design solution meeting the requirements imposed by physical phenomena and operational necessities.


title: Results of an RF Pulsed Heating Experiment at SLAC

abstract: Results are reported from an experiment on RF pulsed heating of copper at SLAC. Damage in the form of cracks may be induced on the surface after the application of many pulses of RF. The experiment consists of two circularly cylindrical cavities operated in the TE011 mode at a resonant frequency of 11.424 GHz. Each cavity received 8.5 MW, 1.2 microsecond pulses at 60 Hz corresponding to a calculated temperature rise of 120 K on the copper surface. After 5.5 x 10^7 pulses, the experiment was stopped and the copper surfaces were examined. Damage is present on the area of the surface where the maximum heating occurred.


title: Energy stabilization of 1.5 GeV S-Band linac

abstract: KEK-ATF is studying low emittance, multi-bunch electron beam for the future linear collider. The energy instability of the 1.5 GeV linac has been a problem making the beam injection to the damping ring unstable. Because the unstable beam generates also large amount of the radiation, the beam current is limited by the KEK radiation safety policy much lower than what we expect. Stabilizing the S-band linac is therefore important not only to improve the beam quality, but also to clear the radiation safety limit to start the multi-bunch operation. We have made various modifications to solve the problem on the electron gun, modulator, klystron etc. For the modulator, we have developed a feed-forward controlled De-Q module. This module compensates the voltage jitter by controlling the deQ timing with a feed-forward circuit because the amount of the excessive charge up is strongly correlated to the charge up slope that can be measured prior to the deQ timing. The energy stability was examined and was improved by a factor of 3, from 0.6% to 0.2% of itself. Modification for the feed-forward circuit to get more stability was made. The test for the new circuit is in progress. For the long term instability, phase-lock system for klystron RF is being installed. In the test operation, it showed a good performance and compensate the phase drift less than 1 deg.


title: 2.856-GHz Modulation of Conventional Triode Electron Gun

abstract: For the generation of picosecond (< 100 ps) electron beam pulses, we studied the RF modulation of a conventional triode electron gun. The feasibility study for this scheme has been experimentally investigated by modulating a triode gun of the Y-824 cathode-grid (KG) structure provided by the CPI Eimac, with 2.856-GHz pulsed RF generated by a solid-state amplifier (SSA). In this paper, we present the methods and results of this investigation.


title: Experimental Determination of the Characteristics of a Positron Source Using Channeling

abstract: Numerical simulations and `proof of principle' experiments showed clearly the interest of using crystals as photon generators dedicated to intense positron sources for linear colliders. An experimental investigation, using a 10 GeV secondary electron beam, of the SPS-CERN, impinging on an axially oriented thick tungsten crystal, has been prepared and operated between May and August 2000. After a short recall on the main features of positron sources using channeling in oriented crystals, the experimental set-up is described. A particular emphasis is put on the positron detector made of a drift chamber, partially immersed in a magnetic field. The enhancement in photon and positron production in the aligned crystal have been observed in the energy range 5 to 40 GeV, for the incident electrons, in crystals of 4 and 8 mm as in an hybrid target. The first results concerning this experiment are presented hereafter.


title: Elliptical X-Ray Spot Measurement

abstract: The so-called roll bar measurement uses a heavy metal material, optically thick to x-rays, to form a shadow of the x-ray origination spot. This spot is where an energetic electron beam interacts with a high Z target. The material (the "roll bar") is slightly curved to avoid alignment problems. The roll bar is constructed and positioned so that the x-rays are shadowed in the horizontal and vertical directions, so information is obtained in two dimensions. If a beam profile is assumed (or measured by other means), the equivalent x-ray spot size can be calculated from the x-ray shadow cast by the roll bar. Thus the ellipticity of the beam can be calculated, assuming the ellipse of the x-ray spot is aligned with the roll bar. The data is recorded using a scintillator and gated camera. Data will be presented from measurements using the ETA II induction LINAC. The accuracy of the measurement is checked using small elliptical targets.


title: High-intensity single-bunch electron beam generation with the 38 MeV L-band linac in Osaka University

abstract: The characteristics of the high-intensity single-bunch electron beam of the 38 MeV L-band electron linac at the Institute of Scientific and Industrial Research in Osaka University were investigated.


title: The effects of the rotation in plasma

abstract: Electric and magnetic self-fields can exist in the rotating plasma. A self-sustained rotation can be established in the plasma. The disturbed distribution function of rotating plasma is derived from the Vlasov equation. The propagation of waves in rotating plasma differs from that in the usual plasma. New terms for Landau damping appear. The local rotational behaviour may become prevailing.


title: The RF source of the 60-MeV Linac for the KEK/JAERI Joint Project

abstract: The construction of the 60-MeV proton linac has started as a low-energy front of the KEK/JAERI Joint Project for a high-intensity proton accelerator facility at KEK. The accelerating frequency is 324 MHz. Five UHF klystrons are used as an rf source; their ratings have a maximum power of 3 MW, a beam pulse width of a 700 micro-sec (an rf pulse width is 650 micro-sec) and a repetition rate of 50 pps. We have manufactured a proto-type rf source (a power-supply system with a modulating-anode pulse modulator and prototype klystrons). In this paper, the specifications and developments of the rf source, including the WR-2300 waveguide system, are summarized. During the manufacturing process, strong oscillations due to back-going electrons from the collector were observed. This phenomenon was analyzed both experimentally and theoretically. We have tested up to an output power of nearly 3 MW, and succeeded to test the DTL hot-model structure.


title: High-Brightness Beams from a Light Source Injector: The Advanced Photon Source Low-Energy Undulator Test Line Linac

abstract: The use of existing linacs, and in particular light source injectors, for free-electron laser (FEL) experiments is becoming more common due to the desire to test FELs at ever shorter wavelengths. The high-brightness, high-current beams required by high-gain FELs impose technical specifications that most existing linacs were not designed to meet. Moreover, the need for specialized diagnostics, especially shot-to-shot data acquisition, demands substantial modification and upgrade of conventional linacs. Improvements have been made to the Advanced Photon Source (APS) injector linac in order to produce and characterize high-brightness beams. Specifically, effort has been directed at generating beams suitable for use in the low-energy undulator test line (LEUTL) FEL in support of fourth-generation light source research. The enhancements to the linac technical and diagnostic capabilities that allowed for self-amplified spontaneous emission (SASE) operation of the FEL at 530 nm are described. Recent results, including details on technical systems improvements and electron beam measurement techniques, will be discussed. The linac is capable of accelerating beams to over 650 MeV. The nominal FEL beam parameters used are as follows: 217 MeV energy; 0.1-0.2% rms energy spread; 4-8 um normalized rms emittance; 80-120 A peak current from a 0.2-0.7 nC charge at a 2-7 ps FWHM bunch.


title: The Flat Beam Experiment at the FNAL Photoinjector

abstract: A technique for production of an electron beam with a high transverse emittance ratio. a "flat" beam, has been proposed by Brinkmann, Derbenev, and Floettmann.[1] The cathode of an RF-laser gun is immersed in a solenoidal magnetic field; as a result the beam emitted from a round laser spot has a net angular momentum. Subsequent passage through a quadrupole channel that has a 90 degree difference in phase advance between the transverse degrees of freedom results in a flat beam. Experimental study is underway at the Fermilab A0 Photoinjector. Thus far, transverse emittance ratios as high as 50 have been observed, and the results are in substantial agreement with simulation. [1] R. Brinkmann, Ya. Derbenev, K. Floettmann, "A Flat Beam Electron Source for Linear Colliders." TESLA Note 99-09, April 1999.


title: Multiscale Analysis of RMS Envelope Dynamics

abstract: We present applications of variational -- wavelet approach to different forms of nonlinear (rational) rms envelope equations. We have the representation for beam bunch oscillations as a multiresolution (multiscales) expansion in the base of compactly supported wavelet bases.

categories: physics.acc-ph math-ph math.MP nlin.CD physics.comp-ph


title: DFQ--Double Frequency RFQ

abstract: RFQ with a harmonic higher order quadrupole mode is studied. Assuming that we superpose a higher order mode with twice the frequency of the fundamental mode, a sawtooth waveform is approximated. In such a case, the bunching function is enhanced while the transverse stability is modified. Second order longitudinal harmonic component is also required to enable the effect.


title: Multiresolution Representation for Orbital Dynamics in Multipolar Fields

abstract: We present the applications of variation -- wavelet analysis to polynomial/rational approximations for orbital motion in transverse plane for a single particle in a circular magnetic lattice in case when we take into account multipolar expansion up to an arbitrary finite number and additional kick terms. We reduce initial dynamical problem to the finite number (equal to the number of n-poles) of standard algebraical problems. We have the solution as a multiresolution (multiscales) expansion in the base of compactly supported wavelet basis.

categories: physics.acc-ph math-ph math.MP nlin.PS physics.comp-ph


title: Nonlinear Beam Dynamics and Effects of Wigglers

abstract: We present the applications of variational--wavelet approach for the analytical/numerical treatment of the effects of insertion devices on beam dynamics. We investigate the dynamical models which have polynomial nonlinearities and variable coefficients. We construct the corresponding wavelet representation for wigglers and undulator magnets.

categories: physics.acc-ph math-ph math.MP nlin.AO physics.comp-ph


title: Spin-Orbital Motion: Symmetry and Dynamics

abstract: We present the applications of variational--wavelet approach to nonlinear (rational) model for spin-orbital motion: orbital dynamics and Thomas-BMT equations for classical spin vector. We represent the solution of this dynamical system in framework of periodical wavelets via variational approach and multiresolution.


title: Local Analysis of Nonlinear RMS Envelope Dynamics

abstract: We present applications of variational -- wavelet approach to nonlinear (rational) rms envelope dynamics. We have the solution as a multiresolution (multiscales) expansion in the base of compactly supported wavelet basis.


title: Multiscale Representations for Solutions of Vlasov-Maxwell Equations for Intense Beam Propagation

abstract: We present the applications of variational--wavelet approach for computing multiresolution/multiscale representation for solution of some approximations of Vlasov-Maxwell equations.


title: Quasiclassical Calculations in Beam Dynamics

abstract: We present some applications of general harmonic/wavelet analysis approach (generalized coherent states, wavelet packets) to numerical/analytical calculations in (nonlinear) quasiclassical/quantum beam dynamics problems. (Naive) deformation quantization, multiresolution representations and Wigner transform are the key points.


title: Some possibilities for laboratory searches for variations of fundamental constants

abstract: We consider different options for the search for possible variations of the fundamental constants. We give a brief overview of the results obtained with several methods. We discuss their advantages and disadvantages with respect to simultaneous variations of all constants in both time and space in the range 10^{8}-10^{10} yr. We also suggest a few possibilities for the laboratory search. Particularly, we propose some experiments with the hyperfine structure of hydrogen, deuterium and ytterbium-171 and of some atoms with a small magnetic moment. Other suggestions are for some measurements of the fine structure associated with the ground state. Special attention is paid to the interpretation of the hfs measurements in terms of variations of the fundamental constants.


title: Design of a 3 GHz Accelerator Structure for the CLIC Test Facility (CTF 3) Drive Beam

abstract: For the CLIC two-beam scheme, a high-current, long-pulse drive beam is required for RF power generation. Taking advantage of the 3 GHz klystrons available at the LEP injector once LEP stops, a 180 MeV electron accelerator is being constructed for a nominal beam current of 3.5 A and 1.5 microsecond pulse length. The high current requires highly effective suppression of dipolar wakes. Two concepts are investigated for the accelerating structure design: the "Tapered Damped Structure" developed for the CLIC main beam, and the "Slotted Iris - Constant Aperture" structure. Both use 4 SiC loads per cell for effective higher-order mode damping. A full-size prototype of the TDS structure has been built and tested successfully at full power. A first prototype of the SICA structure is being built.


title: The Physicist's Guide to the Orchestra

abstract: An experimental study of strings, woodwinds (organ pipe, flute, clarinet, saxophone and recorder), and the voice was undertaken to illustrate the basic principles of sound production in music instruments. The setup used is simple and consists of common laboratory equipment. Although the canonical examples (standing wave on a string, in an open and closed pipe) are easily reproduced, they fail to explain the majority of the measurements. The reasons for these deviations are outlined and discussed.


title: Lifetime Testing 700 MHz RF Windows for the Accelerator Production of Tritium Program

abstract: Radio frequency (RF) windows are historically a point where failure occurs in input-power couplers for accelerators. To understand more about the reliability of high power RF windows, lifetime testing was done on 700 MHz coaxial RF windows for the Low Energy Demonstration Accelerator (LEDA) project of the Accelerator Production of Tritium (APT) program. The RF windows, made by Marconi Applied Technologies (formerly EEV), were tested at 800 kW for an extended period of time. Changes in the reflected power, vacuum, air outlet temperature, and surface temperature were monitored over time. The results of the life testing are summarized.


title: Funneling with the Two-Beam RFQ

abstract: New high current accelerator facilities like proposed for HIDIF or ESS require a beam with a high brilliance. These beams can not be produced by a single pass rf-linac. The increase in brightness in such a driver linac is done by several funneling stages at low energies, in which two identically bunched ion beams are combined into a single beam with twice the frequency current and brightness. Our Two-Beam-RFQ funneling experiment is a setup of two ion sources, a two beam RFQ, a funnel deflector and beam diagnostic equipment to demonstrate funneling of ion beams as a model for the first funneling stage of a HIIF driver. The progress of the funneling experiment and results of simulations will be presented.


title: Overview of the APT Accelerator Design

abstract: The accelerator for the APT Project is a 100 mA CW proton linac with an output energy of 1030 MeV. A High Energy Beam Transport (HEBT) conveys the beam to a raster expander, that provides a large rectangular distribution at a target/blanket (T/B) assembly. Spallation neutrons generated by the proton beam in the T/B reacts with Helium-3 to produce tritium. The design of the APT linac is an integrated normal-conducting (NC)/superconducting (SC) proton linac; the machine architecture has been discussed elsewhere [1]. The NC linac consists of a 75 keV injector, a 6.7-MeV 350-MHz RFQ (radio frequency quadrupole), a 96-MeV 700-MHz CCDTL (coupled-cavity drift-tube linac), and a 700-MHz CCL (coupled-cavity linac), with an output energy of 211 MeV. This is followed by a SC linac, that employs 700-MHz elliptical niobium 5-cell cavities to accelerate the beam to the final energy. The SC linac has two sections, optimized for beam velocities of b =0.64 and b =0.82. Each section is made up of cryomodules containing two, three, or four 5-cell cavities, driven by 1-MW 700-MHz klystrons. The singlet FODO lattice in the NC linac transitions to a doublet focusing lattice in the SC linac, with conventional quadrupole magnets in the warm inter-module spaces. This doublet lattice is continued in the HEBT. An overview of the current linac design will be presented.


title: Reconstruction of Initial Beam Conditions at the Exit of the DARHT II Accelerator

abstract: We consider a technique to determine the initial beam conditions of the DARHT II Accelerator by measuring the beam size under three different magnetic transport settings. This may be time gated to resolve the parameters as a function of time within the 2000 nsec pulse. This technique leads to three equations in three unknowns with solution giving the accelerator exit beam radius, tilt and emittance. We find that systematic errors cancel and so are not a problem in unfolding the initial beam conditions. Random uncorrelated shot to shot errors can be managed by one of three strategies: 1) make the transport system optically de-magnifying; 2) average over many individual shots; or 3) make the random uncorrelated shot to shot errors sufficiently small. The high power of the DARHT II beam requires that the beam transport system leading to a radius measuring apparatus be optically magnifying. This means that the shot to shot random errors must either be made small (less than about 1%) or that we average each of the three beam radius determinations over many individual shots.


title: Quantum string field theory and psychophysics

abstract: The quantum string field theoretic structure of interactive phenomena is discussed


title: The Mechanical Design for the Darht-II Downstream Beam Transport Line

abstract: This paper describes the mechanical design of the downstream beam transport line for the second axis of the Dual Axis Radiographic Hydrodynamic Test (DARHT II) Facility. The DARHT-II project is a collaboration between LANL, LBNL and LLNL. DARHT II is a 20-MeV, 2000-Amperes, 2-msec linear induction accelerator designed to generate short bursts of x-rays for the purpose of radiographing dense objects. The down-stream beam transport line is approximately 20-meter long region extending from the end of the accelerator to the bremsstrahlung target. Within this proposed transport line there are 15 conventional solenoid, quadrupole and dipole magnets; as well as several speciality magnets, which transport and focus the beam to the target and to the beam dumps. There are two high power beam dumps, which are designed to absorb 80-kJ per pulse during accelerator start-up and operation. Aspects of the mechanical design of these elements are presented.


title: Theoretical study of the absorption spectra of the sodium dimer

abstract: Absorption of radiation from the sodium dimer molecular states correlating to Na(3s)-Na(3s) is investigated theoretically. Vibrational bound and continuum transitions from the singlet X Sigma-g+ state to the first excited singlet A Sigma-u+ and singlet B Pi-u states and from the triplet a Sigma-u+ state to the first excited triplet b Sigma-g+ and triplet c Pi-g states are studied quantum-mechanically. Theoretical and experimental data are used to characterize the molecular properties taking advantage of knowledge recently obtained from ab initio calculations, spectroscopy, and ultra-cold atom collision studies. The quantum-mechanical calculations are carried out for temperatures in the range from 500 to 3000 K and are compared with previous calculations and measurements where available.


title: Production And Studies Of Photocathodes For High Intensity Electron Beams

abstract: For short, high-intensity electron bunches, alkali-tellurides have proved to be a reliable photo-cathode material. Measurements of lifetimes in an RF gun of the CLIC Test Facility II at field strengths greater than 100 MV/m are presented. Before and after using them in this gun, the spectral response of the Cs-Te and Rb-Te cathodes were determined with the help of an optical parametric oscillator. The behaviour of both materials can be described by Spicer's 3-step model. Whereas during the use the threshold for photo-emission in Cs-Te was shifted to higher photon energies, that of Rb-Te did not change. Our latest investigations on the stoichiometric ratio of the components are shown. The preparation of the photo-cathodes was monitored with 320 nm wavelength light, with the aim of improving the measurement sensitivity. The latest results on the protection of Cs-Te cathode surfaces with CsBr against pollution are summarized. New investigations on high mean current production are presented.


title: A "hybrid"-type system for an achromatic focusing of ions

abstract: It is known, that at high energies of ions (more than 10 MeV for light ions) the focusing by magnetic quadrupole fields is most effective, whereas at small energies (less than 1 MeV) - the focusing by electrical quadrupole fields. At intermediate energies of ions (from 1 to 10 MeV) the efficiency of each of these types of a focusing is reduced. The authors offer to utilize for this purpose the "hybrid" type of focusing systems consisting of sequence of electrical and magnetic quadrupole lenses, which are localized in the same space. For making fields of electrical quadrupole lenses it is offered to utilize RF quadrupoles. The RF electrical quadrupoles are created due to the relevant configuration of drift tubes in the vicinity of an accelerating gap. As a result of the general theoretical analysis and calculation of concrete versions of practical realizations it is shown that the given system has advantage as contrasted to by known analogs in the field of medium energies. The velocity band of ions, in which the stable motion is ensured, is essentially changed, and the focusing becomes "achromatic". The calculations have been performed for protons with velocities 0.5-1.0 % of light velocity, at the gradients of electrical field up to 50 kV per square cm, and the gradients of magnetic field up to 1 T/m. Achromaticity of this system allows to lower a radiative activation of accelerator and to reduce damage of electrode surfaces by lost ions.


title: Fractal Statistics

abstract: We consider the recent description of elementary particles in terms of Quantum Mechanical Kerr-Newman Black Holes, a description which provides a rationale for and at the same time reconciles the Bohm-hydrodynamical formulation on the one hand and the Nelsonian stochastiic formulation on the other. The Boson-Fermion divide is discussed, and it is pointed out that in special situations, anomalous statistics, rather than Bose-Einstein or Fermi-Dirac states, can be encountered.


title: CLIC, a Two-Beam Multi-TeV e+e- Linear Collider

abstract: The CLIC study of a high-energy (0.5 - 5 TeV), high-luminosity (1034 - 1035 cm-2 sec-1) e+e- linear collider is presented. Beam acceleration using high frequency (30 GHz) normal-conducting structures operating at high accelerating fields (150 MV/m) significantly reduces the length and, in consequence, the cost of the linac. Using parameters derived from general scaling laws for linear colliders, the beam stability is shown to be similar to lower frequency designs in spite of the strong wake-field dependency on frequency. A new cost-effective and efficient drive beam generation scheme for RF power production by the so-called "Two-Beam Acceleration" method is described. It uses a thermionic gun and a fully-loaded normal-conducting linac operating at low frequency (937 MHz) to generate and accelerate the drive beam bunches, and RF multiplication by funnelling in compressor rings to produce the desired bunch structure. Recent 30 GHz hardware developments and CLIC Test Facility (CTF) results are described.


title: Phase Rotation, Cooling And Acceleration Of Muon Beams: A Comparison Of Different Approaches

abstract: Experimental and theoretical activities are underway at CERN with the aim of examining the feasibility of a very-high-flux neutrino source. In the present scheme, a high-power proton beam (some 4 MW) bombards a target where pions are produced. The pions are collected and decay to muons under controlled optical condition. The muons are cooled and accelerated to a final energy of 50 GeV before being injected into a decay ring where they decay under well-defined conditions of energy and emittance. We present the most challenging parts of the whole scenario, the muon capture, the ionisation-cooling and the first stage of the muon acceleration. Different schemes, their performance and the technical challenges are compared.


title: Superconducting H-mode Structures for Medium Energy Beams

abstract: Room temperature IH-type drift tube structures are used at different places now for the acceleration of ions with mass over charge ratios up to 65 and velocities between 0.016 c and 0.1 c. These structures have a high shunt impedance and allow the acceleration of very intense beams at high accelerating gradients. The overall power consumption of room temperature IH-mode structures is comparable with superconducting (sc) structures up to 2 MeV/u. With the KONUS [1] beam dynamics, the required transversal focusing elements, e.g. quadrupole triplets can be placed outside of multicell cavities, which is favourable for building sc H-mode cavities. The design principles and consequences to the geometry compared to room temperature (rt) cavities will be described. The results gained from numerical simulations show that a sc multi-gap H21(0)-mode cavity (CH-type) can be an alternative to the sc spoke-type or reentrant cavity structures up to beam energies around 150 MeV/u. The main cavity parameters and possible fabrication options will be discussed. [1] U. Ratzinger, Nucl. Intr. Meth., A 415 (1998) 229.


title: An injector for the CLIC test Facility (CTF3)

abstract: The CLIC Test Facility (CTF3) is an intermediate step to demonstrate the technical feasibility of the key concepts of the new RF power source for CLIC. CTF3 will use electron beams with an energy range adjustable from 170 MeV (3.5 A) to 380 MeV (with low current). The injector is based on a thermionic gun followed by a classical bunching system embedded in a long solenoidal field. As an alternative, an RF photo-injector is also being studied. The beam dynamics studies on how to reach the stringent beam parameters at the exit of the injector are presented. Simulations performed with the EGUN code showed that a current of 7 A can be obtained with an emittance less than 10 mm.mrad at the gun exit. PARMELA results are presented and compared to the requested beam performance at the injector exit. Sub-Harmonic Bunchers (SHB) are foreseen, to switch the phase of the bunch trains by 180 degrees from even to odd RF buckets. Specific issues of the thermionic gun and of the SHB with fast phase switch are discussed.


title: Pulsed Neutron Source using 100-MeV electron Linac at Pohang Accelerator Laboratory

abstract: The Pohang Accelerator Laboratory operates an electron linac for the pulsed neutron source as one of the long-term nuclear R&D programs at the Korea Atomic Energy Research Institute. The designed beam parameters are as follows; The nominal beam energy is 100 MeV, the maximum beam power is 10 kW, and the beam current is varied from 300 mA to 5A depends on the pulse repetition. The linac has two operating modes: one for short pulse modes with the various repetitions between 2 ns and 100 ns and the other for long pulse modes with 1 ms repetition. We have constructed and tested an electron linac based on the existing equipment such as a SLAC-5045 klystron, two constant gradient accelerating sections, and a thermionic RF-gun. We present the characteristics of the linac and report the status of the pulsed neutron source facilities include a target system and time-of-flight paths.


title: Collector Failures on 350 MHz, 1.2 MW CW Klystrons at the Low Energy Demonstration Accelerator (LEDA)

abstract: We are currently operating the front end of the accelerator production of tritium (APT) accelerator, a 7 MeV radio frequency quadrapole (RFQ) using three, 1.2 MW CW klystrons. These klystrons are required and designed to dissipate the full beam power in the collector. The klystrons have less than 1500 operational hours. One collector has failed and all collectors are damaged. This paper will discuss the damage and the difficulties in diagnosing the cause. The collector did not critically fail. Tube operation was still possible and the klystron operated up to 70% of full beam power with excellent vacuum. The indication that finally led us to the collector failure was variable emission. This information will be discussed. A hydrophonic system was implemented to diagnose collector heating. The collectors are designed to allow for mixed-phase cooling and with the hydrophonic test equipment we are able to observe: normal, single-phase cooling, mixed-phase cooling, and a hard boil. These data will be presented. The worst case beam profile from a collector heating standpoint is presented. The paper will also discuss the steps taken to halt the collector damage on the remaining 350 MHz klystrons and design changes that are being implemented to correct the problem.


title: The Spallation Neutron Source (SNS) Linac RF System

abstract: The SNS linac accelerates an average beam current of 2 mA to an energy of 968 MeV. The linac is pulsed at 60 Hz with an H- beam pulse of 1 ms. The first 185 Mev of the linac uses normal conducting cavities, and the remaining length of the linac uses superconducting cavities. The linac operates at 402.5 MHz up to 87 MeV and then changes to 805 MHz for the remainder. This paper gives an overview of the Linac RF system. The overview includes a description and configuration of the high power RF components, the HV converter/modulator, and the RF controls. Issues and tradeoffs in the RF system will be discussed, especially with regards to the use of pulsed superconducting cavities.


title: Beam Emittance Measurements for the Low-Energy Demonstration Accelerator Radio-Frequency Quadrupole

abstract: The Low-Energy Demonstration Accelerator (LEDA) radio-frequency quadrupole (RFQ) is a 100% duty factor (CW) linac that delivers >100 mA of H+ beam at 6.7 MeV. The 8-m-long, 350-MHz RFQ structure accelerates a dc, 75-keV, 110-mA H+ beam from the LEDA injector with >90% transmission. LEDA [1,2] consists of a 75-keV proton injector, 6.7-MeV, 350-MHz CW RFQ with associated high-power and low-level rf systems, a short high-energy beam transport (HEBT) and high-power (670-kW CW) beam stop. The beam emittance is inferred from wire scanner measurements of the beam profile at a single location in the HEBT. The beam profile is measured as a function of the magnetic field gradient in one of the HEBT quadrupoles. As the gradient is changed the spot size passes through a transverse waist. Measurements are presented for peak currents between 25 and 100 mA.


title: New Developments in Linear Colliders Final Focus Systems

abstract: The length, complexity and cost of the present Final Focus designs for linear colliders grows very quickly with the beam energy. In the paper, a novel final focus system is presented and compared with the one proposed for NLC. This new design is simpler, shorter and cheaper, with comparable bandwidth, tolerances and tunability. Moreover, the length scales slower than linearly with energy allowing for a more flexible design which is applicable over a much larger energy range.


title: CCT, a Code to Automate the Design of Coupled Cavities

abstract: The CCT (Coupled Cavity Tuning) code automates the RF calculations and sizing of RF cavities for the CCL (Coupled Cavity Linac) structures of APT. It is planned to extend the code to the CCDTL (Coupled Cavity Drift Tube Linac). The CCT code controls the CCLFISH code, a member of the Poisson Superfish series of codes [1]. CCLFISH performs RF calculations and tunes the geometry of individual cavities, including an accelerating cavity (AC) and a coupling cavity (CC). CCT also relates the AC and CC by means of equations that describe the coupling slot between cavities. These equations account for the direct coupling, the next nearest neighbor coupling between adjacent AC's, and the frequency shifts in the AC and CC caused by the slot. Given design objectives of a coupling coefficient k, the pi/2 mode frequency, and the net frequency of the CC, the CCT code iterates to solve for the geometry of the AC and CC and the separation distance between them (this controls the slot size), satisfying the design objectives. The resulting geometry is used to automate CAD drawing preparation. The code can also be used in "as-designed" mode to calculate the frequencies and coupling of a specified configuration. An overview of the code is presented.


title: High-Power Testing of the APT Power Coupler

abstract: For the baseline APT (Accelerator Production of Tritium) linac design, power couplers are required to transmit 210-kW of CW RF power to the superconducting cavities. These APT couplers operate at 700 MHz, have a coaxial design and an adjustable coupling to the superconducting cavities. Since May 1999, we have been testing couplers of this design on a room-temperature test stand. We completed tests at transmitted-power and reflected-power conditions up to 1 MW. We also tested the couplers with a portion of the outer conductor cooled by liquid nitrogen. Under this latter condition, we studied the effects of condensed gases on coupler performance. The results of these tests indicate that the APT couplers are capable of delivering more than 500 kW to the cavities. We are in the process of increasing the baseline coupler design requirement to 420 kW of transmitted power to take advantage of this successful development. In this paper, we describe the results of our high-power coupler tests.


title: Possibility of a Light Pulse with Speed Greater than c

abstract: In two models it is shown that a light pulse propagates from a vacuum into certain media with velocity greater than that of a light in a vacuum (c). By numerical calculation the propagating properties of such a light are given.


title: Energy focusing inside a dynamical cavity

abstract: We study the exact classical solutions for a real scalar field inside a cavity with a wall whose motion is self-consistently determined by the pressure of the field itself. We find that, regardless of the system parameters, the long-time solution always becomes nonadiabatic and the field's energy concentrates into narrow peaks, which we explain by means of a simple mechanical system. We point out implications for the quantized theory.


title: Annealing of radiation induced defects in silicon in a simplified phenomenological model

abstract: The concentration of primary radiation induced defects has been previously estimated considering both the explicit mechanisms of the primary interaction between the incoming particle and the nuclei of the semiconductor lattice, and the recoil energy partition between ionisation and displacements, in the frame of the Lindhard theory. The primary displacement defects are vacancies and interstitials, that are essentially unstable in silicon. They interact via migration, recombination, annihilation or produce other defects. In the present work, the time evolution of the concentration of defects induced by pions in medium and high resistivity silicon for detectors is modelled, after irradiation. In some approximations, the differential equations representing the time evolution processes could be decoupled. The theoretical equations so obtained are solved analytically in some particular cases, with one free parameter, for a wide range of particle fluences and/or for a wide energy range of the incident particles, for different temperatures; the corresponding stationary solutions are also presented.


title: Latest Developments from the S-DALINAC*

abstract: The S-DALINAC is a 130 MeV superconducting recirculating electron accelerator serving several nuclear and radiation physics experiments as well as driving an infrared free-electron laser. A system of normal conducting rf resonators for noninvasive beam position and current measurement was established. For the measurement of gamma-radiation inside the accelerator cave a system of Compton diodes has been developed and tested. Detailed investigations of the transverse phasespace were carried out with a tomographical reconstruction method of optical transition radiation spots. The method can be applied also to non-Gaussian phasespace distributions. The results are in good accordance with simulations. To improve the quality factor of the superconducting 3 GHz cavities, an external 2K testcryostat was commissioned. The influence of electro-chemical polishing and magnetic shielding is currently under investigation. A digital rf-feedback-system for the accelerator cavities is being developed in order to improve the energy spread of the beam of the S-DALINAC. * Supported by the BMBF under contract no. 06 DA 820, the DFG under contract no. Ri 242/12-1 and -2 and the DFG Graduiertenkolleg 'Physik und Technik von Beschleunigern'


title: Linac Lue200. First Testing Results

abstract: "LUE200" - 200 MeV electron linac is being created at JINR as a driver of the pulsed neutron source "IREN" [1]. The special full-scale facilities for testing the main systems of LUE-200 (FSTF) are used at JINR, BINP, MEPhI and YerPhI [2]. The verification of the linac accelerating system is providing at the VEPP-5 preinjector constructed at BINP [3]. The accelerating system of LUE200 includes two S-band (2856 MHz) accelerating sections of 3 m long. The sections are connected with modulator based one 5045 klystron (SLAC production). There are SLED-systems for the multiplying the pulse RF power. The first results of the accelerating system test on the VEPP-5 preinjector are presented. The electron beam energy up to 92 MeV and consequently average rate of acceleration of the electron beam more than 30 MeV/m were achieved after acceleration in one section.


title: A Super-Conducting Linac Injector for the BNL-Ags

abstract: This paper reports on the feasibility study of a proton Super-Conducting Linac (SCL) as a new injector to the Alternating Gradient Synchrotron (AGS) of the Brookhaven National Laboratory (BNL). The Linac beam energy is in the range of 1.5 to 2.4 GeV. The Beam intensity is adjusted to provide an average beam power of 4 MW at the top energy of 24 GeV. The repetition rate of the SCL-AGS facility is 5 beam pulses per second.


title: A Super-Conducting Linac Driver for the HFBR

abstract: This paper reports on the feasibility study of a proton Super-Conducting Linac (SCL) as a driver gor the High-Flux Breader Reactor (HFBR) at Brookhaven National Laboratory (BNL). The Linac operates in Continuos Wave (CW) mode to produce an average 10 MW of beam power. The Linac energy is 1.0 GeV. The average proton beam intensity is 10 mA.


title: On the Confidence Interval for the parameter of Poisson Distribution

abstract: The possibility of construction of continuous analogue of Poisson distribution with the search of bounds of confidence intervals for parameter of Poisson distribution is discussed. Also, in the article is shown that the true value of a parameter of Poisson distribution for the observed value $\hat x$ has Gamma distribution with the scale parameter, which is equal to one, and the shape parameter, which is equal to $\hat x$. The results of numerical construction of confidence intervals are presented.


title: Theory of nuclear spin conversion in ethylene

abstract: First theoretical analysis of the nuclear spin conversion in ethylene molecules (13^CCH4) has been performed. The conversion rate was found equal approx. 3x10^{-4} 1/s*Torr, which is in qualitative agreement with the recently obtained experimental value. It was shown that the ortho-para mixing in 13^CCH4 is dominated by the spin-rotation coupling. Mixing of only two pairs of ortho-para levels were found to contribute significantly to the spin conversion.


title: Wire Scanners for Small Emittance Beam Measurement in Atf

abstract: The wire scanners are used for a measurement of the very small beam size and the emittance in Accelerator Test Facility (ATF). They are installed in the extraction beam line of ATF damping ring. The extracted beam emittance are ex=1.3x10-9 m.rad, ey=1.7x10-11 m.rad with 2x109 electrons/bunch intensity and 1.3GeV energy. The wire scanners scan the beam by a tungsten wire with beam repetition 0.78Hz. The scanning speed is, however, very slow(~500um/sec). Since the extracted beam is quite stable by using the double kicker system, precision of the size measurement is less than 2um for 50 - 150um horizontal beam size and 0.3um for 8 - 16um vertical beam size. The detail of the system and the performance are described.


title: Energy Stability in a High Intensity Pulsed SC Proton Linac

abstract: Spallation source dedicated for neutron scattering experiments, as well as multi-purpose facilities serving several applications call for pulsed mode operation of a high intensity proton linac. There is general agreement on the superconducting technology for the high-energy part, which offers some advantages, like higher gradient capabilities or operational costs reduction, as compared to room-temperatures accelerating structures. This mode of operation however could spoil the energy stability of the proton beam and needs thus to be carefully studied. First, transient beam-loading effects, arising from the large beam phase slippage along a multi-cell cavity and associated with the finite RF energy propagation, can induce significant energy modulation with a too small cell-to-cell coupling or a too large number of cells. Second, due to beam phase slippage effects along the linac, energy spread exhibits a larger sensitivity to cavity fields fluctuations than relativistic particles. A computer code, initially developed for electron beams has been extended to proton beams. It solves the 6xN coupled differential equations, needed to describe cavity fields and beam-cavity interactions of a high-energy linac composed of N cavities. Simulation examples on a typical pulsed accelerator are given with various error sources, like Lorentz forces or microphonics detuning, beam injection energy offsets, intensity jitters ...


title: The Low Energy Beam Transport System of the New GSI High Current Injector

abstract: The UNILAC was improved for high current performance by replacing the Wideroe prestripper accelerator by an RFQ and an IH-type DTL. In addition, one of two ion source terminals was equipped with high current sources of MUCIS- and MEVVA-type. Therefore, a redesign of the LEBT from the ion source to the RFQ entrance was necessary. The new LEBT was installed at the beginning of 1999. The commissioning was carried mainly with a high intense argon beam. The achieved 17 emA Ar+ are 6 emA above the RFQ design intensity. The expected performance of the new LEBT was achieved: full transmission for high current beams, preservation of brilliance along the beam line, isotope separation for all elements, transverse phase space matching to the RFQ linac, and macropulse shaping. In particular, the high degree of space charge compensation was confirmed.


title: Commissioning of the 1.4 Mev/u High Current Heavy Ion Linac at Gsi

abstract: The disassembly of the Unilac prestripper linac of the Wideroe type took place at the beginning of 1999. An increase of more than two orders of magnitude in particle number for the most heavy elements in the SIS had to be gained. Since that time the new High Current Injector (HSI) consisting of H-type RFQ and DTL-structures for dual beam operation was installed and successfully commissioned. The High Charge Injector (HLI) supplied the main linac during that time. Simultaneously conditioning and running in of the rf-transmitters and rf-structures were done. The HSI commissioning strategy included beam investigation after each transport and acceleration section, using a versatile diagnostic test stand. Results of the extensive commissioning measurements (e.g. transverse emittance, bunch width, beam transmission) behind LEBT, RFQ, Super Lens, IH tank I and II and stripping section will be discussed. An 40Ar1+ beam coming from a MUCIS ion source was used to fill the linac up to the theoretical space charge limit. Routine operation started in November 1999.


title: The New Gas Stripper and Charge State Separator of the Gsi High Current Injector

abstract: The GSI Unilac was upgraded as a high current injector for the SIS in 1999. Therefore, the stripping section [1] at 1.4 MeV/u, where a beam transport under highest space charge conditions and multi beam operation had to be established, was completely new designed. Results of the commissioning of the stripper section will be presented. The beam transport to the new gas stripper, and the charge state analysis under space charge conditions confirmed the calculations. A 238U4+ beam - coming from a MEVVA ion source and accelerated by the new injector linac- was stripped (with the expected stripping efficiency) to the charge state 28+ and successfully separated by the new spectrometer (15 degree and 30 degree kicker magnets). The transport and matching to the poststripper accelerator under highest space charge conditions was investigated with a 15 emA 40Ar10+ beam. Especially space charge and charge state dependent emittance growth effects in 6d-phase space will be discussed.


title: High-power Circulator Test Results at 350 MHz and 700 MHz

abstract: The high-power RF systems for the Accelerator Production of Tritium (APT) program require high-power circulators at 350 MHz and 700 MHz to protect 1 MW Continuous Wave (CW) klystrons from reflected power. The 350 MHz circulator is based on the CERN, ESRF, and APS designs and has performed very well. The 700 MHz circulator is a new design. Prototype 700 MHz circulators have been high-power tested at Los Alamos National Laboratory (LANL). The first of these circulators has satisfied performance requirements. The circulator requirements, results from the testing, and lessons learned from this development are presented and discussed.


title: Industrial Fabrication of Medium-Beta SCRF Cavities for a High-Intensity Proton Linac

abstract: During 1999, four 700-MHz, medium-beta (b = 0.64), superconducting radio frequency (SCRF) cavities for a high-intensity proton linac project at Los Alamos National Laboratory (LANL) were manufactured by industry. The SCRF cavities were designed by a LANL team in Los Alamos, New Mexico, USA, and manufactured at a CERCA plant in Romans, France. The cavities were made of 4-mm-thick, solid niobium sheets with a residual resistivity ratio (RRR) greater than 250. These niobium sheets were supplied by Wah Chang (USA), Heraeus AG (Germany), and Tokyo Denkai (Japan). The SCRF cavities were shipped to LANL for performance testing. This paper describes the experience gained during the manufacturing process at CERCA.


title: The Diffraction Model and its Applicability for Wakefield Calculations

abstract: The operation of a Free Electron Laser (FEL) in the ultraviolet or in the X-ray regime requires the acceleration of electron bunches with an rms length of 25 to 50 micro meters. The wakefields generated by these sub picosecond bunches extend into the frequency range well beyond the threshold for Cooper pair breakup (about 750 GHz) in superconducting niobium at 2 K. It is shown, that the superconducting cavities can indeed be operated with 25 micro meter bunches without suffering a breakdown of superconductivity (quench), however at the price of a reduced quality factor and an increased heat transfer to the superfluid helium bath. This was first shown by wakefield calculations based on the diffraction model. In the meantime a more conventional method of computing wake fields in the time domain by numerical methods was developed and used for the wakefield calculations. Both methods lead to comparable results: the operation of TESLA with 25 micro meter bunches is possible but leads to an additional heat load due to the higher order modes (HOMs). Therefore HOM dampers for these high frequencies are under construction. These dampers are located in the beam pipes between the 9-cell cavities. So it is of interest, if there are trapped modes in the cavity due to closed photon orbits. In this paper we investigate the existence of trapped modes and the distribution of heat load over the surface of the TESLA cavity by numerical photon tracking.


title: Spectroscopic investigations of a dielectric-surface-discharge plasma source

abstract: Spectroscopic investigations of the properties of a plasma produced by a flashboard plasma source, commonly used in pulsed plasma experiments, are presented. The plasma is used to prefill a planar 0.4-ms-conduction time plasma opening switch (POS). A novel gas-doping technique and a secondary surface flashover plasma source are used to locally dope the plasma with gaseous and solid materials, respectively, allowing for spatially-resolved measurements. The electron density, temperature, and plasma composition are determined from spectral line intensities and line profiles. Detailed collisional-radiative modeling is used to analyze the observed line intensities. The propagation velocity and divergence angle of various ions are determined from time-of-flight measurements and Doppler broadening of spectral lines, respectively. This allows for distinguishing the secondary plasma ejected from the POS electrodes from the plasma of the flashboard source.


title: Automated Operation of the APS LINAC using the Procedure Execution Manager

abstract: The Advanced Photon Source (APS) linear accelerator has two thermionic cathode rf guns and one photocathode rf gun. The thermionic guns are used primarily for APS operations while the photocathode gun is used as a free-electron laser (FEL) driver. With each gun requiring a different lattice and timing configuration, the need to change quickly between guns puts great demands on the accelerator operators. Using the Procedure Execution Manager (PEM), a software environment for managing automated procedures, we have made start-up and switch-over of the linac systems both easier and more reliable. The PEM is a graphical user interface written in Tcl/Tk that permits the user to invoke "machine procedures" and control their execution. It allows construction of procedures in a hierarchical, parallel fashion, which makes for efficient execution and development. In this paper, we discuss the features and advantages of the PEM environment as well the specifics of our procedures for the APS linac.


title: The quantum vacuum, fractal geometry, and the quest for a new theory of gravity

abstract: In this letter recent developments are shown in experimental and theoretical physics which brings into question the validity of General Relativity. This letter emphasizes the construction of a fractal 3+\phi^3 spacetime, in N-dimensions in order to formalize a physical and consistent theory of `quantum gravity.' It is then shown that a `quantum gravity' effect could arise by means of the Strong Equivalence Principle. Which is made possible through a pressure of the form -kappa(R^{ca}_{b}-{1\over 2}g^{c sigma}_{ab}R^c)=kappa T^{c sigma}_{ab}. Where it is seen that nuclear pressures can be added to rethe gravitational field equations by means of twistor spaces.


title: Beam Position-Phase Monitors for SNS Linac

abstract: Electromagnetic modeling with MAFIA of the combined beam position-phase monitors (BPPMs) for the Spallation Neutron Source (SNS) linac has been performed. Time-domain 3-D simulations are used to compute the signal amplitudes and phases on the BPPM electrodes for a given processing frequency, 402.5 MHz or 805 MHz, as functions of the beam transverse position. Working with a summed signal from all the BPPM electrodes provides a good way to measure accurately the beam phase. While for an off-axis beam the signal phases on the individual electrodes can differ from those for a centered beam by a few degrees, the phase of the summed signal is found to be independent of the beam transverse position inside the device. Based on the analysis results, an optimal BPPM design with 4 one-end-shorted 60-degree electrodes has been chosen. It provides a good linearity and sufficient signal power for both position and phase measurements, while satisfying the linac geometrical constrains and mechanical requirements.


title: Bridge Coupler for APT

abstract: The Coupled Cavity Drift Tube Linac (CCDTL) used in the Accelerator for the Production of Tritium (APT) is fully described elsewhere [1]. The modules are composed of several machined and brazed segments that must account for the accumulation of dimensional tolerances in the build up of the stack. In addition, space requirements dictate that power fed to the accelerator cannot be through the accelerating cavities. As well, we would like to remove a single segment of the accelerator without removing additional segments. These requirements combined with phasing relationships of the design and space limitations have resulted in a different bridge coupling method used in the module comprising 3-gap segments. The coupling method, phasing relationships and other features that enhance the flexibility of the design will be discussed.


title: LEDA Beam Operations Milestone and Observed Beam Transmission Characteristics

abstract: Recently, the Low-Energy Demonstration Accelerator (LEDA) portion of the Accelerator Production of Tritium (APT) project reached its 100-mA, 8-hr CW beam operation milestone. LEDA consists of a 75-keV proton injector, 6.7-MeV, 350-MHz CW radio-frequency quadrupole (RFQ) with associated high-power and low-level rf systems, a short high-energy beam transport (HEBT) and high-power (670-kW CW) beam dump. During the commissioning phase it was discovered that the RFQ field level must to be approximately 5-10% higher than design in order to accelerate the full 100-mA beam with low losses. Measurements of a low-duty-factor, 100-mA beam show the beam transmission is unexpectedly low for RFQ field levels between ~90 and 105% of design. This paper will describe some aspects of LEDA operations critical to achieving the above milestone. Measurement and simulation results for reduced RFQ beam transmission near design operating conditions are also presented.


title: RF Control System for the NLC Linacs

abstract: The proposed Next Linear Collider contains a large number of linac RF systems with new requirements for wideband klystron modulation and accurate RF vector detection. The system will be capable of automatically phasing each klystron and compensating for beam loading effects. Accelerator structure alignment is determined by detection of the beam induced dipole modes with a receiver similar to that used for measuring the accelerator RF and is incorporated into the RF system topology. This paper describes the proposed system design, signal processing techniques and includes preliminary test results.


title: RF Cell Modeling and Experiments for Wakefield Minimization in DARHT-II

abstract: Electron beams of linear induction accelerators experience deflective forces caused by RF fields building up as a result of accelerating cavities of finite size. These forces can significantly effect the beam when a long linac composed of identical cells is assembled. Recent techniques in computational modeling, simulation, and experiments for 20 MeV DARHT-II (Dual Axis Radiographic Hydrodynamic Test) accelerator cells were found to reduce the wakefield impedance of the cells from 800 ohms/meter to 350 ohms/meter and experimental results confirm the results of the modeling efforts. Increased performance of the cell was obtained through a parametric study of the accelerator structure, materials, material tuning, and geometry. As a result of this effort, it was found that thickness-tuned ferrite produced a 50% deduction in the wakefield impedance in the low frequency band and was easily tunable based on the material thickness. It was also found that shaped metal sections allow for high-Q resonances to be de-tuned, thus decreasing the amplitude of the resonance and increasing the cell s performance. For the geometries used for this cell, a roughly 45 degree angle had the best performance in affecting the wakefield modes.


title: Test of accelerating structure for VEPP-5 preinjector

abstract: Preinjector VEPP-5 electron linac consists of two linear accelerators on energy 300 MeV and 510 MeV and includes 14 accelerating structures [1]. First accelerating structures both linacs have increased average rate of acceleration 25-30 MeV/m, and other regular sections up to 17-20 MeV/m. This paper presents the results of basic test of 3-meter long accelerating structure. Average rate of acceleration of an electron beam 35 MeV/m was achieved. The electron beam energy up to 105 MeV was obtained.


title: The CLIC Main Linac Accelerating Structure

abstract: This paper outlines the RF design of the CLIC (Compact Linear Collider) 30 GHz main linac accelerating structure and gives the resulting longitudinal and transverse mode properties. The critical requirement for multibunch operation, that transverse wakefields be suppressed by two orders of magnitude within 0.7 ns (twenty fundamental mode cycles), has been demonstrated in a recent ASSET experiment. The feasibility of operating the structure at an accelerating gradient of 150 MV/m for 130 ns has yet to be demonstrated. Damage of the internal copper surfaces due to high electric fields or resulting from metal fatigue induced by cyclic surface heating effects are a major concern requiring further study.


title: Tests of the CERN Proton Linac Performance for LHC-Type Beams

abstract: As the pre-injector of the LHC injector chain, the proton linac at CERN is required to provide a high-intensity (180mA) beam to the Proton Synchrotron Booster. The results of measurements at this intensity will be presented. Furthermore, the linac is now equipped with bunch shape monitors from INR, Moscow, which have allowed the comparison of the Alvarez tank RF settings with simulations.


title: Measurement of the six Dimensional Phase Space at the New GSI High Current Linac

abstract: For the characterization of the 10 mA ion beam delivered by the new High Current Linac at GSI, sophisticated, mainly non-intersepting diagnostic devices were developed. Besides the general set-up of a versatile test bench, we discuss in particular bunch shape and emittance measurements. A direct time-of-flight technique with a diamond particle detector is used to observe the micro-bunch distribution with a resolution of $\sim 25 $ ps equals 0.3$^{o}$ in phase. For the determination of the energy spread a coincidence technique is applied, using secondary electrons emitted by the ion passing through an aluminum foil 80 cm upstream of the diamond detector. The transverse emittance is measured within one macro pulse with a pepper-pot system equipped with a high performance CCD camera.


title: Superconducting Superstructure for the TESLA Collider: New Results

abstract: A new cavity-chain layout has been proposed for the main linac of the TESLA linear collider. This superstructure-layout is based upon four 7-cell superconducting standing-wave cavities, coupled by short beam pipes. The main advantages of the superstructure are an increase in the active accelerating length in TESLA and a saving in rf components, especially power couplers, as compared to the present 9-cell cavities. The proposed scheme allows to handle the field-flatness tuning and the HOM damping at sub-unit level, in contrast to standard multi-cell cavities. The superstructure-layout is extensively studied at DESY since 1999. Computations have been performed for the rf properties of the cavity-chain, the bunch-to-bunch energy spread and multibunch dynamics. A copper model of the superstructure has been built in order to compare with the simulations and for testing the field-profile tuning and the HOM damping scheme. A "proof of principle" niobium prototype of the superstructure is now under construction and will be tested with beam at the TESLA Test Facility in 2001. In this paper we present latest results of these investigations.


title: Beam Dynamics Studies for a High Current Ion Injector

abstract: Recent ion source developments resulted in the generation of high brilliance, high current beams of protons and light ions. After extraction and transport the beams with large internal space charge forces have to be captured, bunched and preaccelerated for the injection into the following driver part of a new generation of high intensity beam facilities for neutron sources, energy production, transmutation e.g. A combination of RFQ and DTL is considered to be a good solution for such a high current ion injector. Some preliminary beam dynamics layouts have been investigated by multiparticle simulations. Basic parameters like frequency, ion energy and sparking have been varied for the International Fusion Material Irradiation Facility (IFMIF) scenario as an example. The main interest was directed to high transmission, low losses and emittance conservation. The beam matching to the RFQ is shortly discussed as well as the matching between RFQ and DTL.


title: High Current Beam Dynamics in an Ess SC Linac

abstract: Three alternative designs of the European Spallation Source (ESS) high energy linac are described. The most promising ones are either a normalconducting (nc) coupled cavity linac (CCL) up tofinal energy or a change at 407 MeV to only one group of 6 cell superconducting (sc) elliptical cavities. Fully 3d Monte Carlo simulations are presented for both options, optimized for reduced halo formation at the linac end. For the error free matched case, especially the halo formation in the longitudinal plane is more pronounced for the hybrid solution with its superconducting cavities, caused by the unavoidable phase slippage, but still quite well acceptable for loss free ring injection. Simulations however for a 30% mismatched dense core, surrounded in addition by 1.5% halo particles are showing few particles with very large amplitudes even in real space. This case represents halo formation in front to end simulations, caused by current fluctuations, filamented RFQ output distribution and enhanced by accumulated field errors.


title: Studies of Coupled Cavity Linac (CCL) Accelerating Structures with 3-D Codes

abstract: The cw CCL being designed for the Accelerator Production of Tritium (APT) project accelerates protons from 96MeV to 211MeV. It consists of 99 segments each containing up to seven accelerating cavities. Segments are coupled by intersegment coupling cavities and grouped into supermodules. The design method needs to address not only basic cavity sizing for a given coupling and pi/2 mode frequency, but also the effects of high power densities on the cavity frequency, mechanical stresses, and the structure's stop band during operation. On the APT project, 3-D RF (Ansoft Corp.'s HFSS) and coupled RF/structural (Ansys Inc.'s ANSYS) codes are being used to develop tools to address the above issues and guide cooling channel design. The code's predictions are being checked against available low power Aluminum models. Stop band behavior under power will be checked once the tools are extended to CCDTL structures that have been tested at high power. A summary of calculations made to date and agreement with measured results will be presented.


title: Estimates of dispersive effects in a bent NLC main linac

abstract: An alternative being considered for the Next Linear Collider (NLC) is not to tunnel in a straight line but to bend the Main Linac into an arc so as to follow an equipotential. We begin here an examination of the effects that this would have on vertical dispersion, with its attendant consequences on synchrotron radiation and emittance growth by looking at two scenarios: a gentle continuous bending of the beam to follow an equipotential surface, and an introduction of sharp bends at a few sites in the linac so as to reduce the maximum sagitta produced.


title: Analyses of klystron modulator approaches for NLC

abstract: Analyze of experimental results shows that the energy discharge efficiency of the modern modulators is 0.92-0.93. The energy transfer efficiency can be reached up to 0.7 for 1.5 usec pulse width and up to 0.8 for 3.0 usec accordingly. The geometry and core material of the transformer is one element of modulator, which limits the efficiency due to limitation if transmission band of the pulse power. Ways of the rise of energy transfer efficiency had been discussed. The use of features of coupled transmission lines lies in the base of an idea how the energy transfer efficiency can be improved up to 0.85 in the frame of the conventional approach. In the second part of the paper the transformerless modulator approaches are presented upon a modified Marx method of voltage multiplication using on/off IGBT instead of on switches.


title: Operational Aspects of the High Current Upgrade at the Unilac

abstract: With the new GSI High Current Injector, the beam pulse intensity will be increased by more than two orders of magnitude. The high beam power and the short stopping range at particle energies below 12 MeV/u can destroy accelerator components even during a single beam pulse. Therefore, the operation of the whole accelerator facility has required major changes in hardware, software and operating strategy. A sophisticated beam diagnostic system is indispensable for a safe operation. Preferably non-destructive devices were installed. Destructive elements, e.g. beam stoppers, slits, apertures, were improved in order to withstand the high beam power. Automatic damage prevention was realised by beam loss monitors comparing and evaluating very fast beam current transformer signals. Additionally, the component status will be controlled permanently. For foil stripping at 11.4 MeV/u, a magnetic beam sweeping system was installed Thereby, the hit area will be increased during one 100 micro sec pulse. During operation, manual variation of parameters has to be reduced. Set-up and automatic beam adjustment procedures have to exclude uncontrolled beam loss. The versatility of the UNILAC is enhanced by the possible three-beam operation on a pulse-to-pulse basis. Since November 1999 the upgraded UNILAC is serving the experiments.


title: Looking Forward to Pricing Options from Binomial Trees

abstract: We reconsider the valuation of barrier options by means of binomial trees from a "forward looking" prospective rather than the more conventional "backward induction" one used by standard approaches. This reformulation allows us to write closed-form expressions for the value of European and American put barrier-options on a non-dividend-paying stock.


title: Design and Performance Simulations of the Bunch Compressor for the APS LEUTL FEL

abstract: A magnetic bunch compressor has been designed and is being commissioned for the APS linac to provide higher peak current for the LEUTL FEL. Of primary concern is control of emittance growth due to coherent synchrotron radiation (CSR). In addition, tolerances must be carefully evaluated in order to choose the most stable operating conditions and ensure that the system can meet operational goals. The computer code ELEGANT was used to design the bunch compressor, set tolerances, and simulate likely performance. This 6-D code includes a fast, simple simulation of CSR effects as well as longitudinal and transverse wakefields. It also is believed to be unique in allowing optimization of actual tracking results, such as bunch length, energy spread, and emittance. Automated setup and analysis of matching and tolerance simulations allowed consideration of numerous configurations without excessive effort. This permitted choosing configurations that reduce sensitivity to errors. Simulations indicate that emittance growth should be tolerable for up to 600 A peak current, for which the normalized emittance will increase from 5 to about 6.8 pi-um. The simulations also provide predictions of emittance variation with chicance parameters, which we hope to verify experimentally. * Work supported by the U.S. Department of Energy, Office of Basic Energy Sciences, under Contract No. W-31-109-ENG-38.


title: Design of the SNS Normal Conducting Linac RF Control System

abstract: The Spallation Neutron Source (SNS) is being designed for operation in 2004. The SNS is a 1 GeV machine consisting of a combination normal-conducting and super-conducting linac as well as a ring and target area. The linac front end is a 402.5 MHz RFQ being developed by Lawrence Berkeley Lab. The DTL (at 402.5 MHz) and the CCL (at 805 MHz) stages are being developed by Los Alamos National Laboratory. The expected output energy of the DTL is 87 MeV and that of the CCL is 185 MeV. The RF control system under development for the linac is based on the Low Energy Demonstration Accelerator (LEDA) control system with some new features. This paper will discuss the new design approach and its benefits. Block diagrams and circuit specifics will be addressed. The normal conducting RF control system will be described in detail with references to the super-conducting control system where appropriate.


title: A Highly Flexible Bunch Compressor for the APS LEUTL FEL

abstract: The LEUTL FEL at the APS has achieved gain at 530 nm with peak beam current \~100 A. In an effort to push to 120 nm and beyond, we have designed and are commissioning a bunch compressor to increase the peak current to 600 A or more. The bunch compressor uses a four-dipole chicane at an energy of 100 to 210 MeV. To provide options for control of emittance growth due to coherent synchrotron radiation (CSR), the chicane has variable R56. The central pair of dipoles is movable, accommodating variable R56 with less concern about emittance dilution from nonuniformity of the dipole field. The symmetry of the chicane is also variable via longitudinal motion of the final dipole, which is predicted to have an effect on emittance growth. Following the chicane, a three-screen emittance measurement system should permit resolution of the difference in emittance growth between various chicane configurations. A vertical bending magnet analysis line is present to permit imaging of correlations between transverse and energy coordinates. This paper reviews the features and expected performance of the chicane. A companion paper discusses the physics design in detail. Work supported by the U.S. Department of Energy, Office of Basic Energy Sciences, under Contract No. W-31-109-ENG-38.


title: Space Charge Effects in Bunch Shape Monitors

abstract: The operation and parameters of Bunch Shape Monitors using coherent transformation of time structure of an analyzed beam into a spatial one of low energy secondary electrons emitted from a wire target is influenced by the characteristics of a beam under study. The electromagnetic field of a bunch disturbs the trajectories of secondary electrons, thus resulting in a degradation of phase resolution and in errors of phase reading. Another effect is the perturbation of the target potential due to the current in the wire induced by a bunch as well as due to current compensating emission of the secondary electrons. The methods, the models and the results of simulations are presented.


title: Use of Coherent Transition Radiation to Set Up the APS RF Thermionic Gun to Produce High-Brightness Beams for SASE FEL Experiments

abstract: We describe use of the Advanced Photon Source (APS) rf thermionic gun, alpha magnet beamline, and linac to produce a stable high-brightness beam in excess of 100 amperes peak current with normalized emittance of 10 pi mm-mrad. To obtain peak currents greater than 100 amperes, the rf gun system must be tuned to produce a FWHM bunch length on the order of 350 fs. Bunch lengths this short are measured using coherent transition radiation (CTR) produced when the rf gun beam, accelerated to 40 MeV, strikes a metal foil. The CTR is detected using a Golay detector attached to one arm of a Michelson interferometer. The alpha magnet current and gun rf phase are adjusted so as to maximize the CTR signal at the Golay detector, which corresponds to the minimum bunch length. The interferometer is used to measure the autocorrelation of the CTR radiation. The minimum phase approximation is used to derive the bunch profile from the autocorrelation. The high-brightness beam is accelerated to 217 MeV and used to produce SASE in five APS undulators installed in the Low- Energy Undulator Test Line (LEUTL) experiment hall. Initial optical measurements showed a gain length of 1.3 m at 530 nm. * Work supported by U. S. Department of Energy, Office of Basic Energy Sciences, under Contract No. W-31-109-ENG-38.


title: Coherent Synchrotron Radiation Measurements in the CLIC Test Facility (CTF II)

abstract: Bunches of high charge (up to 10 nC) are compressed in length in the CTF II magnetic chicane to less than 0.2 mm rms. The short bunches radiate coherently in the chicane magnetic field, and the horizontal and longitudinal phase space density distributions are affected. This paper reports the results of beam emittance and momentum measurements. Horizontal and vertical emittances and momentum spectra were measured for different bunch compression factors and bunch charges. In particular, for 10 nC bunches, the mean beam momentum decreased by about 5% while the FWHM momentum spread increased from 5% to 19%. The experimental results are compared with simulations made with the code TraFiC4.